WHISP-SM-MIB

All MIBs › WHISP-SM-MIB

Organization: Cambium Networks

Last Updated: 2003-04-15

Category: Cambium/Motorola Wireless Broadband

Description: Manages Cambium Networks Canopy Subscriber Module radio link statistics, signal levels, and session parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is WHISP-SM-MIB?

WHISP-SM-MIB is a vendor-specific MIB from Cambium Networks (formerly Motorola) for the Canopy Subscriber Module, a fixed wireless broadband radio used in point-to-multipoint access networks. It groups objects into configuration, security, status, group membership, and event/DFS-event categories, exposing radio link parameters, session state, and dynamic frequency selection activity. Its monitoring focus is on wireless hardware and link status: signal levels, session statistics, and radio link quality that reveal whether a subscriber's wireless connection is healthy or degraded, along with security and DFS event logs that flag interference or regulatory channel-switch conditions. It is a self-contained vendor MIB, typically used alongside the companion WHISP-BOX (AP) MIBs and standard interface MIBs in the same deployment. It is deployed on Canopy Subscriber Modules at customer premises, polled by WISP network operations centers for link-quality assurance using the WHISP-SM-MIB MIB as the reference for the exposed radio and session objects.

IPNetwork Monitor allows you to monitor SNMP objects defined in WHISP-SM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cambium/Motorola Canopy Subscriber Module (SM)
fixed wireless broadband CPE radio

Monitoring Examples

An operator would query objects under whispSmStatus to check current signal strength and session uptime for a subscriber radio, and check whispSmDfsEvent to see if the module recently vacated a channel due to detected radar. whispSmConfig and whispSmSecurity expose the configured RF and authentication settings that would be compared against expected values during a link-quality troubleshooting session. A spike in whispSmEvent entries alongside falling signal metrics typically indicates a subscriber link is experiencing interference or hardware degradation.

What Can Be Monitored

radio signal strength
session status
security/authentication state
group membership
DFS channel-switch events
link quality events

Imported Objects

From SNMPv2-CONF

OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
PhysAddress

From WHISP-BOX-MIBV2-MIB

dhcpRfPublicIp	OBJECT-TYPE
whispBoxEsn	OBJECT-TYPE

From WHISP-GLOBAL-REG-MIB

whispAps	OBJECT-IDENTITY
whispBox	OBJECT-IDENTITY
whispModules	OBJECT-IDENTITY
whispSm	OBJECT-IDENTITY

From WHISP-TCV2-MIB

WhispLUID
WhispMACAddress

How to Use in IPNetwork Monitor

Example using nbBitsRcvd OID:

Select a Cambium/Motorola Canopy Subscriber Module (SM), fixed wireless broadband CPE radio (signal-level/session/DFS-event status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type nbBitsRcvd into the Find box to locate it in the OID tree, then select it and click OK. It reports the number of BER bits received (non MIMO platforms only). On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
whispSmMibModule	1.3.6.1.4.1.161.19.1.1.13			This module contains MIB definitions for Subscriber Modem.
whispSmConfig	1.3.6.1.4.1.161.19.3.2.1
STR rfScanList	1.3.6.1.4.1.161.19.3.2.1.1	DisplayString	read-write	RF scan list. The frequencies are: 2.4 radios:24150,24175,24200,24225,24250,24275,24300,24325,24350,24375, 24400,24425,24450,24475,24500,24525,24550,24575. 3.5 radios:340000-360000 added and removed dynamically. 4.9 radios:494500-498500 added and removed dynamically. 5.1 radios:5175,5180,5185,5190,5195,5200,5205,5210,5215,5220,5225,5230,5240, 5245,5250,5255,5260,5265,5270,5275,5280,5285,5290,5295,5300,5305, 5310,5315,5320,5325. 5.2 radios:5275,5280,5285,5290,5295,5300,5305,5310,5315,5320,5325. 5.4 FSK radios:5495,5500,5505,5510,5515,5520,5525, 5530,5535,5540,5545,5550,5555,5560,5565,5570,5575,5580,5585,5590,5595, 5600,5605,5610,5615,5620,5625,5630,5635,5640,5645,5650,5655,5660,5665, 5670,5675,5680,5685,5690,5695,5700,5705. 5.4 OFDM radios 5 mhz channels: 547250,547500,547750,548000,548500,548750,549000,549250,549500,549750,550000,550250,550500,550750,551000,551250,551500,551750,552000,552250,552500,552750, 553000,553250,553500,553750,554000,554250,554500,554750,555000,555250,555500,555750,556000,556250,556500,556750,557000,557250,557500,557750,558000,558250,558500,558750,559000,559250,559500,559750, 560000,560250,560500,560750,561000,561250,561500,561750,562000,562250,562500,562750,563000,563250,563500,563750,564000,564250,564500,564750,565000,565250,565500,565750,566000,566250,566500,566750, 567000,567250,567500,567750,568000,568250,568500,568750,569000,569250,569500,569750,570000,570250,570500,570750,571000,571250,571500,571750. 5.4 OFDM radios 10 mhz channels: 547500,548500,549000,549500,550000,550500,551000,551500,552000,552500, 553000,553500,554000,554500,555000,555500,556000,556500,557000,557500,558000,558500,559000,559500, 560000,560500,561000,561500,562000,562500,563000,563500,564000,564500,565000,565500,566000,566500, 567000,567500,568000,568500,569000,569500,570000,570500,571000,571500. 5.4 OFDM radios 20 mhz channels: 547500,548500,549000,549500,550000,550500,551000,551500,552000,552500, 553000,553500,554000,554500,555000,555500,556000,556500,557000,557500,558000,558500,559000,559500, 560000,560500,561000,561500,562000,562500,563000,563500,564000,564500,565000,565500,566000,566500, 567000,567500,568000,568500,569000,569500,570000,570500,571000,571500. 5.7 FSK radios with ISM enabled :5735,5740,5745,5750,5755,5760,5765,5770,5775, 5780,5785,5790,5795,5800,5805,5810,5815,5820,5825,5830,5835,5840. 5.7 OFDM radios 5 mhz channels :572750,573000,573250,573500,573750,574000,574250,574500,574750,575000,575250,575500,575750,576000,576250,576500,576750,577000,577250,577500,577750, 578000,578250,578500,578750,579000,579250,579500,579750,580000,580250,580500,580750,581000,581250,581500,581750,582000,582250,582500,582750,583000,583250,583500,583750,584000, 584250,584500,584750,585000,585250,585500,585750,586000,586250,586500,586750,587000,587250. 5.7 OFDM radios 10 mhz channels:573000,573500,574000,574500,575000,575500,576000,576500,577000,577500, 578000,578500,579000,579500,580000,580500,581000,581500,582000,582500,583000,583500,584000,584500,585000,585500,586000,586500,587000. 5.7 OFDM radios 20 mhz channels :573500,574000,574500,575000,575500,576000,576500,577000,577500, 578000,578500,579000,579500,580000,580500,581000,581500,582000,582500,583000,583500,584000,584500,585000,585500,586000,586500. 5.8 radios:5860,5865,5870,5875,5880,5885,5890,5895,5900,5905,5910. 5805,5810,5815,5820,5825,5830,5835,5840,5845,5850,5855,5860,5865,5870,5875,5880, 5885,5890,5895,5900,5905,5910,5915,5920,5925,5930,5935,5940,5945,5950. 5.9 radios:5735,5740,5745,5750,5755,5760,5765,5770,5775,5780,5785,5790,5795,5800, 5805,5810,5815,5820,5825,5830,5835,5840,5845,5850,5855,5860,5865,5870,5875,5880, 5885,5890,5895,5900,5905,5910,5915,5920,5925,5930,5935,5940,5945,5950. 6.050 radios:5850,5855,5860,5865,5870,5875,5880,5885,5890,5895,5900,5905,5910,5915,5920, 5925,5930,5935,5940,5945,5950,5955,5960,5965,5970,5975,5980,5985,5990,5995,6000, 6005,6010,6015,6020,6025,6030,6035,6040,6045,6050. 900 radios:9060,9070,9080,9090,9100,9110,9120,9130,9140,9150,9160,9170,9180,9190,9200,9220,9230,9240. 0: none. all: All frequencies in the band(s) supported by the radio will be selected. all54: All frequencies in the 5.4 band will be selected (only available on dual band radios). all57: All frequencies in the 5.7 band will be selected (only available on dual band radios). When doing a set, separate values with comma with no white space between values.
INT powerUpMode	1.3.6.1.4.1.161.19.3.2.1.2	INTEGER	read-write	SM Power Up Mode With No 802.3 Link. 1 -- Power up in Aim mode 2 -- Power up in Operational mode.
IP lanIpSm	1.3.6.1.4.1.161.19.3.2.1.3	IpAddress	read-write	LAN IP.
IP lanMaskSm	1.3.6.1.4.1.161.19.3.2.1.4	IpAddress	read-write	LAN subnet mask.
IP defaultGwSm	1.3.6.1.4.1.161.19.3.2.1.5	IpAddress	read-write	Default gateway.
INT networkAccess	1.3.6.1.4.1.161.19.3.2.1.6	INTEGER	read-write	Network accessibility. Public or local IP. For multipoint only.
STR authKeySm	1.3.6.1.4.1.161.19.3.2.1.7	DisplayString	read-write	Authentication key. It should be equal or less than 32 characters long.
INT enable8023link	1.3.6.1.4.1.161.19.3.2.1.8	INTEGER	read-write	To enable or disable 802.3 link. For SMs only.
INT authKeyOption	1.3.6.1.4.1.161.19.3.2.1.9	INTEGER	read-write	This option is for SMs only. Backhaul timing slave always uses the set key. 0 - Use default key. 1 - Use set key.
INT timingPulseGated	1.3.6.1.4.1.161.19.3.2.1.10	INTEGER	read-write	0 - Disable (Always propagate the frame timing pulse). 1 - Enable (If SM out of sync then dont propagate the frame timing pulse).
IP naptPrivateIP	1.3.6.1.4.1.161.19.3.2.1.11	IpAddress	read-write	NAPT private IP address. Only the first three bytes can be changed when NAPT is enabled.
IP naptPrivateSubnetMask	1.3.6.1.4.1.161.19.3.2.1.12	IpAddress	read-write	NAPT private subnet mask. Only the last byte can be changed when NAPT is enabled. The address will always be: 255.255.255.x.
IP naptPublicIP	1.3.6.1.4.1.161.19.3.2.1.13	IpAddress	read-write	IP Address of NAPT Public Interface. The variable is available only when NAPT is enabled.
IP naptPublicSubnetMask	1.3.6.1.4.1.161.19.3.2.1.14	IpAddress	read-write	Subnet mask for NAPT Public Interface. The variable is available only when NAPT is enabled.
IP naptPublicGatewayIP	1.3.6.1.4.1.161.19.3.2.1.15	IpAddress	read-write	IP Address of NAPT Public Interface Gateway. The variable is available only when NAPT is enabled.
IP naptRFPublicIP	1.3.6.1.4.1.161.19.3.2.1.16	IpAddress	read-write	IP Address of RF Public Interface. The variable is available only when NAPT is enabled.
IP naptRFPublicSubnetMask	1.3.6.1.4.1.161.19.3.2.1.17	IpAddress	read-write	Subnet mask of RF Public Interface. The variable is available only when NAPT is enabled.
IP naptRFPublicGateway	1.3.6.1.4.1.161.19.3.2.1.18	IpAddress	read-write	IP Address of RF Public Interface Gateway. The variable is available only when NAPT is enabled.
INT naptEnable	1.3.6.1.4.1.161.19.3.2.1.19	INTEGER	read-write	To enable or disable NAPT. For multipoint only. 1=Enable NAPT, 0=Disable NAPT.
INT arpCacheTimeout	1.3.6.1.4.1.161.19.3.2.1.20	INTEGER	read-write	ARP cache time out in unit of minutes. For multipoint only. Range from 1-30.
INT tcpGarbageCollectTmout	1.3.6.1.4.1.161.19.3.2.1.21	INTEGER	read-write	Units of minutes for TCP garbage collection. For multipoint only. Range 4-1440.
INT udpGarbageCollectTmout	1.3.6.1.4.1.161.19.3.2.1.22	INTEGER	read-write	Units of minutes for UDP garbage collection. For multipoint only. Range 1-1440.
INT dhcpClientEnable	1.3.6.1.4.1.161.19.3.2.1.23	INTEGER	read-write	To enable or disable DHCP client. For multipoint SM's with NAPT enabled.
INT dhcpServerEnable	1.3.6.1.4.1.161.19.3.2.1.24	INTEGER	read-write	To enable or disable DHCP server. For multipoint SM's with NAPT enabled.
INT dhcpServerLeaseTime	1.3.6.1.4.1.161.19.3.2.1.25	INTEGER	read-write	Units of days for DHCP server lease time. For multipoint SM's with NAPT enabled. Range from 1-30.
IP dhcpIPStart	1.3.6.1.4.1.161.19.3.2.1.26	IpAddress	read-write	The last byte will be set for the starting IP that our DHCP server gives away. The first 3 bytes of the starting IP are the same as those of NAPT private IP
INT dnsAutomatic	1.3.6.1.4.1.161.19.3.2.1.27	INTEGER	read-write	To have DHCP Server obtain DNS information automatically or manually.
IP prefferedDNSIP	1.3.6.1.4.1.161.19.3.2.1.28	IpAddress	read-write	The preferred DNS IP when we are configured for static DNS (Not used when configured for automatic DNS).
IP alternateDNSIP	1.3.6.1.4.1.161.19.3.2.1.29	IpAddress	read-write	The alternate DNS IP when we are configured for static DNS (Not used when configured for automatic DNS).
IP dmzIP	1.3.6.1.4.1.161.19.3.2.1.30	IpAddress	read-write	Only the last byte of DMZ Host IP will be set. The first 3 bytes of DMZ IP are the same as those of NAPT private IP.
INT dmzEnable	1.3.6.1.4.1.161.19.3.2.1.31	INTEGER	read-write	To enable or disable DMZ host functionality.
INT dhcpNumIPsToLease	1.3.6.1.4.1.161.19.3.2.1.32	INTEGER	read-write	Number of IP addresses that our DHCP server can give away.
INT pppoeFilter	1.3.6.1.4.1.161.19.3.2.1.33	INTEGER	read-write	To set PPPoE packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT smbFilter	1.3.6.1.4.1.161.19.3.2.1.34	INTEGER	read-write	To set SMB packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT snmpFilter	1.3.6.1.4.1.161.19.3.2.1.35	INTEGER	read-write	To set SNMP packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT userP1Filter	1.3.6.1.4.1.161.19.3.2.1.36	INTEGER	read-write	To set user defined port 1 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT userP2Filter	1.3.6.1.4.1.161.19.3.2.1.37	INTEGER	read-write	To set user defined port 2 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT userP3Filter	1.3.6.1.4.1.161.19.3.2.1.38	INTEGER	read-write	To set user defined port 3 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT allOtherIpFilter	1.3.6.1.4.1.161.19.3.2.1.39	INTEGER	read-write	To set all other IPv4 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT upLinkBCastFilter	1.3.6.1.4.1.161.19.3.2.1.40	INTEGER	read-write	This variable is currently obsolete.
INT arpFilter	1.3.6.1.4.1.161.19.3.2.1.41	INTEGER	read-write	To set ARP packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT allOthersFilter	1.3.6.1.4.1.161.19.3.2.1.42	INTEGER	read-write	To set all other packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT userDefinedPort1	1.3.6.1.4.1.161.19.3.2.1.43	INTEGER	read-write	An integer value of number one user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT port1TCPFilter	1.3.6.1.4.1.161.19.3.2.1.44	INTEGER	read-write	To set user defined port 1 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT port1UDPFilter	1.3.6.1.4.1.161.19.3.2.1.45	INTEGER	read-write	To set user defined port 1 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT userDefinedPort2	1.3.6.1.4.1.161.19.3.2.1.46	INTEGER	read-write	An integer value of number two user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT port2TCPFilter	1.3.6.1.4.1.161.19.3.2.1.47	INTEGER	read-write	To set user defined port 2 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT port2UDPFilter	1.3.6.1.4.1.161.19.3.2.1.48	INTEGER	read-write	To set user defined port 2 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT userDefinedPort3	1.3.6.1.4.1.161.19.3.2.1.49	INTEGER	read-write	An integer value of number three user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT port3TCPFilter	1.3.6.1.4.1.161.19.3.2.1.50	INTEGER	read-write	To set user defined port 3 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT port3UDPFilter	1.3.6.1.4.1.161.19.3.2.1.51	INTEGER	read-write	To set user defined port 3 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT bootpcFilter	1.3.6.1.4.1.161.19.3.2.1.52	INTEGER	read-write	To set bootp client sourced packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT bootpsFilter	1.3.6.1.4.1.161.19.3.2.1.53	INTEGER	read-write	To set bootp server sourced packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT ip4MultFilter	1.3.6.1.4.1.161.19.3.2.1.54	INTEGER	read-write	To set IPv4 MultiCast packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT ingressVID	1.3.6.1.4.1.161.19.3.2.1.55	INTEGER	read-write	Untagged ingress VID.
INT lowPriorityUplinkCIR	1.3.6.1.4.1.161.19.3.2.1.56	INTEGER	read-write	Low priority uplink CIR.
INT lowPriorityDownlinkCIR	1.3.6.1.4.1.161.19.3.2.1.57	INTEGER	read-write	Low priority downlink CIR.
INT hiPriorityChannel	1.3.6.1.4.1.161.19.3.2.1.58	INTEGER	read-write	To enable or disable high priority channel.
INT hiPriorityUplinkCIR	1.3.6.1.4.1.161.19.3.2.1.59	INTEGER	read-write	High priority uplink CIR.
INT hiPriorityDownlinkCIR	1.3.6.1.4.1.161.19.3.2.1.60	INTEGER	read-write	High priority downlink CIR.
INT smRateAdapt	1.3.6.1.4.1.161.19.3.2.1.61	INTEGER	read-write	Rate adaptation parameter. 0: no rate adaptation. 1: 1x and 2x adaptation. 2: 1x,2x and 3x adaptation.
INT upLnkDataRate	1.3.6.1.4.1.161.19.3.2.1.62	INTEGER	read-write	Sustained uplink bandwidth cap.
INT upLnkLimit	1.3.6.1.4.1.161.19.3.2.1.63	INTEGER	read-write	Burst uplink bandwidth cap.
INT dwnLnkDataRate	1.3.6.1.4.1.161.19.3.2.1.64	INTEGER	read-write	Sustained downlink bandwidth cap.
INT dwnLnkLimit	1.3.6.1.4.1.161.19.3.2.1.65	INTEGER	read-write	Burst downlink bandwidth cap.
INT dfsConfig	1.3.6.1.4.1.161.19.3.2.1.66	INTEGER	read-write	To configure proper regions for Dynamic Frequency Shifting. For 5.2/5.4/5.7 GHz radios.
INT ethAccessFilterEnable	1.3.6.1.4.1.161.19.3.2.1.67	INTEGER	read-write	To enable or disable Ethernet Port access filtering to SM Management Functions. (0) - Ethernet access to SM Management allowed. (1) - Ethernet access to SM Management blocked.
INT ipAccessFilterEnable	1.3.6.1.4.1.161.19.3.2.1.68	INTEGER	read-write	To enable or disable IP access filtering to Management functions. (0) - IP access will be allowed from all addresses. (1) - IP access will be controlled using allowedIPAccess1-3 entries.
IP allowedIPAccess1	1.3.6.1.4.1.161.19.3.2.1.69	IpAddress	read-write	Allow access to SM Management from this IP. 0 is default setting to allow from all IPs.
IP allowedIPAccess2	1.3.6.1.4.1.161.19.3.2.1.70	IpAddress	read-write	Allow access to SM Management from this IP. 0 is default setting to allow from all IPs.
IP allowedIPAccess3	1.3.6.1.4.1.161.19.3.2.1.71	IpAddress	read-write	Allow access to SM Management from this IP. 0 is default setting to allow from all IPs.
INT rfDhcpState	1.3.6.1.4.1.161.19.3.2.1.72	INTEGER	read-write	To enable or disable RF Interface DHCP feature.
INT bCastMIR	1.3.6.1.4.1.161.19.3.2.1.73	INTEGER	read-write	To enable and set Broadcast/ Multicast MIR feature. Use value of 0 to disable. Units are in kbps
INT bhsReReg	1.3.6.1.4.1.161.19.3.2.1.74	INTEGER	read-write	Allows BHS re-registration every 24 hours. Enable allows re-registration and Disable does not. 24 Hour Encryption Refresh.
INT smLEDModeFlag	1.3.6.1.4.1.161.19.3.2.1.75	INTEGER	read-write	To set LED Panel Operation to Revised Mode(1) or to Legacy Mode(0)
INT ethAccessEnable	1.3.6.1.4.1.161.19.3.2.1.76	INTEGER	read-write	To enable or disable Ethernet Port access to SM Management Functions. (1) - Ethernet access to SM Management allowed. (0) - Ethernet access to SM Management blocked.
INT pppoeEnable	1.3.6.1.4.1.161.19.3.2.1.77	INTEGER	read-write	Enable or disable PPPoE on the SM. NAT MUST be enabled prior and Translation Bridging MUST be DISABLED on the AP.
INT pppoeAuthenticationType	1.3.6.1.4.1.161.19.3.2.1.78	INTEGER	read-write	Set the PPPoE Authentication Type to either None or CHAP/pap
STR pppoeAccessConcentrator	1.3.6.1.4.1.161.19.3.2.1.79	DisplayString	read-write	Set the PPPoE Access Concentrator Name. Less than or equal to 32 characters
STR pppoeServiceName	1.3.6.1.4.1.161.19.3.2.1.80	DisplayString	read-write	Set the PPPoE Service Name. Less than or equal to 32 characters
STR pppoeUserName	1.3.6.1.4.1.161.19.3.2.1.81	DisplayString	read-write	Set the PPPoE Username. Less than or equal to 32 characters
STR pppoePassword	1.3.6.1.4.1.161.19.3.2.1.82	DisplayString	read-write	Set the PPPoE Password. Less than or equal to 32 characters
INT pppoeTCPMSSClampEnable	1.3.6.1.4.1.161.19.3.2.1.83	INTEGER	read-write	Enable or disable TCP MSS Clamping. Enabling this will cause the SM to edit the TCP MSS in TCP SYN and SYN-ACK packets. This will allow for a workaround for MTU issues so that the TCP session will only go up to the clamped MSS. If you are using PMTUD reliably, this should not be needed.
INT pppoeMTUOverrideEnable	1.3.6.1.4.1.161.19.3.2.1.84	INTEGER	read-write	Enable the overriding of the PPP link's MTU. Normally, the PPP link will set the MTU to the MRU of the PPPoE Server, but this may be overridden. If the MRU of the PPPoE server is smaller than the desired MTU, the smaller MTU will be used.
INT pppoeMTUOverrideValue	1.3.6.1.4.1.161.19.3.2.1.85	INTEGER	read-write	Enable the overriding of the PPP link's MTU. Normally, the PPP link will set the MTU to the MRU of the PPPoE Server, but this may be overridden. If the MRU of the PPPoE server is smaller than the desired MTU, the smaller MTU will be used. Max MTU of a PPPoE link is 1492.
INT pppoeTimerType	1.3.6.1.4.1.161.19.3.2.1.86	INTEGER	read-write	Set the PPPoE Timer type. Can be a Keep Alive timer where the link will be checked periodically and automatically redialed if the link is down. Also could be an Idle Timeout where the link will be automatically dropped after an idle period and redialed if user data is present. Keep Alive timers are in seconds while Idle Timeout timers are in minutes.
INT pppoeTimeoutPeriod	1.3.6.1.4.1.161.19.3.2.1.87	INTEGER	read-write	The Timeout Period. The use of this depends on the Timer Type. If the Timer Type is KeepAlive, then the timeout period is in seconds. If the Timer Type is Idle Timeout, then the timeout period is in minutes. Minimum values are 20 seconds for KeepAlive timer, and 5 minutes for Idle Timeout.
INT timedSpectrumAnalysisDuration	1.3.6.1.4.1.161.19.3.2.1.88	INTEGER	read-write	As of release 13.0.2 this value is depricated. Please use the OID in whispBoxConfig. Value in seconds for a timed spectrum analysis. Range is 10-1000 seconds.
INT spectrumAnalysisOnBoot	1.3.6.1.4.1.161.19.3.2.1.89	INTEGER	read-write	To enable or disable Spectrum Analysis on boot up for one scan through the band. (0) - Disabled (1) - Enabled
INT spectrumAnalysisAction	1.3.6.1.4.1.161.19.3.2.1.90	INTEGER	read-write	As of release 13.0.2, this OID has been deprecated. Please use the OID in whispBoxConfig. Start or stop timed or continuous Spectrum Analysis and also give status. (0) - Stop Spectrum Analysis (1) - Start Timed Spectrum Analysis (2) - Start Continuous Spectrum Analysis (3) - Idle, no Spectrum Analysis results. (4) - Idle, Spectrum Analysis results available. (5) - Timed or Remote Spectrum Analysis in progress. (6) - Continuous Spectrum Analysis in progress. Note: Continuous mode has a max of 24 hours.
INT pppoeConnectOD	1.3.6.1.4.1.161.19.3.2.1.91	INTEGER	read-write	Force a manual PPPoE connection attempt.
INT pppoeDisconnectOD	1.3.6.1.4.1.161.19.3.2.1.92	INTEGER	read-write	Force a manual PPPoE disconnection.
INT smAntennaType	1.3.6.1.4.1.161.19.3.2.1.93	INTEGER	read-write	Deprecated. See whispBoxStatus.antType for antenna type information.
INT natConnectionType	1.3.6.1.4.1.161.19.3.2.1.94	INTEGER	read-write	To configure the SM NAT connection type. Options are Static IP, DHCP, or PPPoE.
INT wanPingReplyEnable	1.3.6.1.4.1.161.19.3.2.1.95	INTEGER	read-write	Allow Ping replies from SM WAN interface. Applies to both NAT and PPPoE WAN interfaces.
INT packetFilterDirection	1.3.6.1.4.1.161.19.3.2.1.96	INTEGER	read-write	To packet filter direction when NAT is disabled. Upstream is default. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT colorCode2	1.3.6.1.4.1.161.19.3.2.1.97	INTEGER	read-write	Second Color code.
INT colorCodepriority2	1.3.6.1.4.1.161.19.3.2.1.98	INTEGER	read-write	Priority setting for second color code.
INT colorCode3	1.3.6.1.4.1.161.19.3.2.1.99	INTEGER	read-write	Third Color code.
INT colorCodepriority3	1.3.6.1.4.1.161.19.3.2.1.100	INTEGER	read-write	Priority setting for the third color code.
INT colorCode4	1.3.6.1.4.1.161.19.3.2.1.101	INTEGER	read-write	Fourth Color code.
INT colorCodepriority4	1.3.6.1.4.1.161.19.3.2.1.102	INTEGER	read-write	Priority setting for the fourth color code.
INT colorCode5	1.3.6.1.4.1.161.19.3.2.1.103	INTEGER	read-write	Fifth Color code.
INT colorCodepriority5	1.3.6.1.4.1.161.19.3.2.1.104	INTEGER	read-write	Priority setting for the fifth color code.
INT colorCode6	1.3.6.1.4.1.161.19.3.2.1.105	INTEGER	read-write	Sixth Color code.
INT colorCodepriority6	1.3.6.1.4.1.161.19.3.2.1.106	INTEGER	read-write	Priority setting for the sixth color code.
INT colorCode7	1.3.6.1.4.1.161.19.3.2.1.107	INTEGER	read-write	Seventh Color code.
INT colorCodepriority7	1.3.6.1.4.1.161.19.3.2.1.108	INTEGER	read-write	Priority setting for the seventh color code.
INT colorCode8	1.3.6.1.4.1.161.19.3.2.1.109	INTEGER	read-write	Eighth Color code.
INT colorCodepriority8	1.3.6.1.4.1.161.19.3.2.1.110	INTEGER	read-write	Priority setting for the eighth color code.
INT colorCode9	1.3.6.1.4.1.161.19.3.2.1.111	INTEGER	read-write	Ninth Color code.
INT colorCodepriority9	1.3.6.1.4.1.161.19.3.2.1.112	INTEGER	read-write	Priority setting for the ninth color code.
INT colorCode10	1.3.6.1.4.1.161.19.3.2.1.113	INTEGER	read-write	Tenth Color code.
INT colorCodepriority10	1.3.6.1.4.1.161.19.3.2.1.114	INTEGER	read-write	Priority setting for the tenth color code.
INT natDNSProxyEnable	1.3.6.1.4.1.161.19.3.2.1.115	INTEGER	read-write	If enabled, the SM will advertise itself as the DNS server when it sends out DHCP client leases and forward DNS queries automatically. If disabled, the SM will forward on upstream DNS server information when it sends out DHCP client leases.
INT allIpv4Filter	1.3.6.1.4.1.161.19.3.2.1.116	INTEGER	read-write	To set all IPv4 packet filter when NAT is disabled. Enabling this will automatically enable all of the known IP filters (SMB, SNMP, Bootp, IPv4 Mcast, User Defined Ports, and All Other IPv4). Obsolete - Use corresponding OID in whipsBoxConfig MIB.
INT spectrumAnalysisDisplay	1.3.6.1.4.1.161.19.3.2.1.117	INTEGER	read-write	The display for Spectrum Analyzer: (0) - Averaging over entire period (1) - Instantaneous showing the last reading
INT syslogSMXmitSetting	1.3.6.1.4.1.161.19.3.2.1.118	INTEGER	read-write	Obtains Syslog transmit configuration from AP/BHM if set to 0, overrides if 1 or 2. Transmits syslog data to Syslog server if enabled(1), stops if disabled (2).
INT syslogServerApPreferred	1.3.6.1.4.1.161.19.3.2.1.119	INTEGER	read-write	Uses Syslog server configuration from AP/BHM if enabled and available, otherwise uses local configuration.
INT syslogMinLevelApPreferred	1.3.6.1.4.1.161.19.3.2.1.120	INTEGER	read-write	Uses Syslog minimum transmit level configuration from AP/BHM if available, otherwise uses local configuration.
INT syslogSMXmitControl	1.3.6.1.4.1.161.19.3.2.1.121	INTEGER	read-write	Obtains Syslog transmit configuration from AP/BHM if available, or specifies the local transmit state.
STR eapPeerAAAServerCommonName	1.3.6.1.4.1.161.19.3.2.1.126	DisplayString	read-write	THIS OID IS CURRENTLY UNUSED: EAP Peer Server Common Name
INT rfScanListBandFilter	1.3.6.1.4.1.161.19.3.2.1.127	INTEGER	read-write	This element is obsolete.
INT upLnkMaxBurstDataRate	1.3.6.1.4.1.161.19.3.2.1.128	INTEGER	read-write	Maximum burst uplink rate.
INT dwnLnkMaxBurstDataRate	1.3.6.1.4.1.161.19.3.2.1.129	INTEGER	read-write	Maximum burst downlink rate.
STR cyclicPrefixScan	1.3.6.1.4.1.161.19.3.2.1.130	DisplayString	read-write	Cyclic Prefix value for frequency scanning used by MIMO SMs only. When setting use a comma delimited list of cyclic prefixes with no spaces. For example: 1/8,1/16
STR bandwidthScan	1.3.6.1.4.1.161.19.3.2.1.131	DisplayString	read-write	Bandwidth values for frequency scanning used by MIMO SMs only. When setting use a comma delimited list of bandwidths. For example: 10, 20
INT apSelection	1.3.6.1.4.1.161.19.3.2.1.132	INTEGER	read-write	This OID affects what AP to attempt to register to when Canopy SMs scan see more than one AP that are valid in it's configuration. (0) - Default, Canopy radios after scanning select the best AP that will optimize for estimated throughput. (1) - Select the AP with the best receive power level. Note this is only if multiple APs fit the current scan configuration, and will be overriden by color codes, RADIUS, etc.
INT radioBandscanConfig	1.3.6.1.4.1.161.19.3.2.1.133	INTEGER	read-write	Used to determine when frequency, cyclic prefix and bandwidth settings take effect for band scanning MIMO SMs. 0 - Instant 1 - Delayed 2 - Apply changes
INT forcepoweradjust	1.3.6.1.4.1.161.19.3.2.1.134	INTEGER	read-write	This will force a multipoint SM to initiate an asynchronous power adjust sequence.
INT clearBerrResults	1.3.6.1.4.1.161.19.3.2.1.135	INTEGER	read-write	This will clear the BERR results.
INT berrautoupdateflag	1.3.6.1.4.1.161.19.3.2.1.136	INTEGER	read-write	This indicates if the once a second BERR updating of counters is enabled. 1 = enabled 0 = disabled
INT testSMBER	1.3.6.1.4.1.161.19.3.2.1.137	INTEGER	read-write	0 - Disable (Return the SM to a normal operation state). 1 - Enable (Set SM into a BERR test state).
INT allowedIPAccessNMLength1	1.3.6.1.4.1.161.19.3.2.1.138	INTEGER	read-write	Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed
INT allowedIPAccessNMLength2	1.3.6.1.4.1.161.19.3.2.1.139	INTEGER	read-write	Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed
INT allowedIPAccessNMLength3	1.3.6.1.4.1.161.19.3.2.1.140	INTEGER	read-write	Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed
INT naptRemoteManage	1.3.6.1.4.1.161.19.3.2.1.141	INTEGER	read-write	To enable or disable Remote Management. For multipoint only. 0=Disable Remote Management, 1=Enable - Standalone Config, 2=Enable - Use WAN Interface.
INT spectrumAnalysisScanBandwidth	1.3.6.1.4.1.161.19.3.2.1.142	INTEGER	read-write	Scanning Bandwidth used for the Spectrum Analyzer. Only available on PMP 450.
INT berDeModSelect	1.3.6.1.4.1.161.19.3.2.1.143	INTEGER	read-write	The BER demodulation level the SM is set. 0 for QPSK, 1 for 16-QAM, 2 for 64-QAM, and 3 for 256-QAM.
STR multicastVCRcvRate	1.3.6.1.4.1.161.19.3.2.1.144	DisplayString	read-only	Multicast VC Receive Rate
INT pmp430ApRegistrationOptions	1.3.6.1.4.1.161.19.3.2.1.145	INTEGER	read-write	Selects AP types (430 and/or 450) that are available for the PMP430 SM. When both AP types are selected, if the SM does not register to an AP, it will reboot to scan the other AP type.
INT switchRadioModeAndReboot	1.3.6.1.4.1.161.19.3.2.1.146	INTEGER	read-write	Setting this to 1 will force switch the SM to the other radio mode and immediately reboot the unit. When the unit finishes rebooting, it will be in finishedReboot state. Only will be allowed to be set if both registration options are configured. PMP 430 SM only. Introduced in release 12.2.
whispSmStatus	1.3.6.1.4.1.161.19.3.2.2
STR sessionStatus	1.3.6.1.4.1.161.19.3.2.2.1	DisplayString	read-only	SM registered or not.
INT rssi	1.3.6.1.4.1.161.19.3.2.2.2	INTEGER	read-only	Radio signal strength index. FSK only.
G32 jitter	1.3.6.1.4.1.161.19.3.2.2.3	Gauge32	read-only	A measure of multipath interference. Applicable to FSK radios only.
U32 airDelay	1.3.6.1.4.1.161.19.3.2.2.4	Unsigned32	read-only	Round trip delay in bits.
INT radioSlicingSm	1.3.6.1.4.1.161.19.3.2.2.5	INTEGER	read-only	This variable is deprecated.
INT radioTxGainSm	1.3.6.1.4.1.161.19.3.2.2.6	INTEGER	read-only	Radio transmission gain setting. Applicable to FSK radios only.
STR calibrationStatus	1.3.6.1.4.1.161.19.3.2.2.7	DisplayString	read-only	Varible deprecated. Please use calibrationStatusBox.
STR radioDbm	1.3.6.1.4.1.161.19.3.2.2.8	DisplayString	read-only	Rx Power level. For MIMO this is the combined power of the horizontal and vertical paths.
STR registeredToAp	1.3.6.1.4.1.161.19.3.2.2.9	DisplayString	read-only	AP MAC address that the SM registered to.
IP dhcpCip	1.3.6.1.4.1.161.19.3.2.2.10	IpAddress	read-only	Assigned IP address to DHCP client.
IP dhcpSip	1.3.6.1.4.1.161.19.3.2.2.11	IpAddress	read-only	Public DHCP server IP.
TIK dhcpClientLease	1.3.6.1.4.1.161.19.3.2.2.12	TimeTicks	read-only	DHCP client lease time.
IP dhcpCSMask	1.3.6.1.4.1.161.19.3.2.2.13	IpAddress	read-only	Public DHCP server subnet mask.
IP dhcpDfltRterIP	1.3.6.1.4.1.161.19.3.2.2.14	IpAddress	read-only	Public default router IP address.
IP dhcpcdns1	1.3.6.1.4.1.161.19.3.2.2.15	IpAddress	read-only	Primary public domain name server.
IP dhcpcdns2	1.3.6.1.4.1.161.19.3.2.2.16	IpAddress	read-only	Secondary public domain name server.
IP dhcpcdns3	1.3.6.1.4.1.161.19.3.2.2.17	IpAddress	read-only	Third public domain name server.
STR dhcpDomName	1.3.6.1.4.1.161.19.3.2.2.18	DisplayString	read-only	Public domain name server.
dhcpServerTable	1.3.6.1.4.1.161.19.3.2.2.19		not-accessible	The table of DHCP server hosts.
dhcpServerEntry	1.3.6.1.4.1.161.19.3.2.2.19.1		not-accessible	Entry of DHCP server hosts.
IP hostIp	1.3.6.1.4.1.161.19.3.2.2.19.1.1	IpAddress	read-only	DHCP server IP address.
PHY hostMacAddress	1.3.6.1.4.1.161.19.3.2.2.19.1.2	PhysAddress	read-only	Private host MAC address.
TIK hostLease	1.3.6.1.4.1.161.19.3.2.2.19.1.3	TimeTicks	read-only	Lease time assigned by DHCP server host.
STR adaptRate	1.3.6.1.4.1.161.19.3.2.2.20	DisplayString	read-only	VC adapt rate.
INT radioDbmInt	1.3.6.1.4.1.161.19.3.2.2.21	INTEGER	read-only	Radio power level(integer). For MIMO radios this is the combined power of the horiztontal and vertical paths.
STR dfsStatus	1.3.6.1.4.1.161.19.3.2.2.22	DisplayString	read-only	Dynamic frequency shifting status. For DFS Radio only.
STR radioTxPwr	1.3.6.1.4.1.161.19.3.2.2.23	DisplayString	read-only	Tx Power level. Valid for FSK and OFDM SMs.
STR activeRegion	1.3.6.1.4.1.161.19.3.2.2.24	DisplayString	read-only	The active region of the radio.
INT snmpBerLevel	1.3.6.1.4.1.161.19.3.2.2.25	INTEGER	read-only	BER level. For PMP450 systems: 2=MIMO QPSK, 4=MIMO 16-QAM, 6=MIMO64-QAM, 8=256-QAM For non PMP450: 2=2 level BER, 4=4 level BER.
C64 nbBitsRcvdEx	1.3.6.1.4.1.161.19.3.2.2.26	Counter64	read-only	Number of BER bits received (non MIMO platforms only).
C32 nbPriBitsErr	1.3.6.1.4.1.161.19.3.2.2.27	Counter32	read-only	Number of Primary bit errors (non MIMO platforms only).
C32 nbSndBitsErr	1.3.6.1.4.1.161.19.3.2.2.28	Counter32	read-only	Number of secondary bit errors (non MIMO platforms only).
INT primaryBER	1.3.6.1.4.1.161.19.3.2.2.29	INTEGER	read-only	Obsoleted, invalid type to represent this data. Measured Primary Bit Error Rate.
INT secondaryBER	1.3.6.1.4.1.161.19.3.2.2.30	INTEGER	read-only	Obsoleted, invalid type to represent this data. Measured Secondary Bit Error Rate.
INT totalBER	1.3.6.1.4.1.161.19.3.2.2.31	INTEGER	read-only	Obsoleted, invalid type to represent this data. Measured Total Bit Error Rate.
INT minRSSI	1.3.6.1.4.1.161.19.3.2.2.32	INTEGER	read-only	Measured Min. RSSI. Applicable to FSK radios only.
INT maxRSSI	1.3.6.1.4.1.161.19.3.2.2.33	INTEGER	read-only	Measured Max. RSSI. Applicable to FSK radios only.
G32 minJitter	1.3.6.1.4.1.161.19.3.2.2.34	Gauge32	read-only	Measured Min. Jitter. Applicable to FSK radios only.
G32 maxJitter	1.3.6.1.4.1.161.19.3.2.2.35	Gauge32	read-only	Measured Max. Jitter. Applicable to FSK radios only.
TIK smSessionTimer	1.3.6.1.4.1.161.19.3.2.2.36	TimeTicks	read-only	SM current session timer.
STR pppoeSessionStatus	1.3.6.1.4.1.161.19.3.2.2.37	DisplayString	read-only	Current PPPoE Session Status
INT pppoeSessionID	1.3.6.1.4.1.161.19.3.2.2.38	INTEGER	read-only	Current PPPoE Session ID
IP pppoeIPCPAddress	1.3.6.1.4.1.161.19.3.2.2.39	IpAddress	read-only	Current PPPoE IPCP IP Address
INT pppoeMTUOverrideEn	1.3.6.1.4.1.161.19.3.2.2.40	INTEGER	read-only	Current PPPoE MTU Override Setting
INT pppoeMTUValue	1.3.6.1.4.1.161.19.3.2.2.41	INTEGER	read-only	Current PPPoE MTU Value
INT pppoeTimerTypeValue	1.3.6.1.4.1.161.19.3.2.2.42	INTEGER	read-only	Current PPPoE Timer Type. 0 is disabled, 1 is Keep Alive timer, and 2 is Idle Timeout timer.
INT pppoeTimeoutValue	1.3.6.1.4.1.161.19.3.2.2.43	INTEGER	read-only	Current PPPoE Timeout Period. The use of this depends on the Timer Type. If the Timer Type is KeepAlive, then the timeout period is in seconds. If the Timer Type is Idle Timeout, then the timeout period is in minutes.
IP pppoeDNSServer1	1.3.6.1.4.1.161.19.3.2.2.44	IpAddress	read-only	PPPoE DNS Server 1
IP pppoeDNSServer2	1.3.6.1.4.1.161.19.3.2.2.45	IpAddress	read-only	PPPoE DNS Server 2
C32 pppoeControlBytesSent	1.3.6.1.4.1.161.19.3.2.2.46	Counter32	read-only	PPPoE Control Bytes Sent
C32 pppoeControlBytesReceived	1.3.6.1.4.1.161.19.3.2.2.47	Counter32	read-only	PPPoE Control Bytes Received
C32 pppoeDataBytesSent	1.3.6.1.4.1.161.19.3.2.2.48	Counter32	read-only	PPPoE Data Bytes Sent
C32 pppoeDataBytesReceived	1.3.6.1.4.1.161.19.3.2.2.49	Counter32	read-only	PPPoE Data Bytes Received
INT pppoeEnabledStatus	1.3.6.1.4.1.161.19.3.2.2.50	INTEGER	read-only	PPPoE Enabled
INT pppoeTCPMSSClampEnableStatus	1.3.6.1.4.1.161.19.3.2.2.51	INTEGER	read-only	PPPoE TCP MSS Clamping Enable
STR pppoeACNameStatus	1.3.6.1.4.1.161.19.3.2.2.52	DisplayString	read-only	Current PPPoE Access Concentrator In Use
STR pppoeSvcNameStatus	1.3.6.1.4.1.161.19.3.2.2.53	DisplayString	read-only	Current PPPoE Service Name In Use
TIK pppoeSessUptime	1.3.6.1.4.1.161.19.3.2.2.54	TimeTicks	read-only	Uptime of current PPPoE Session in ticks
STR primaryBERDisplay	1.3.6.1.4.1.161.19.3.2.2.55	DisplayString	read-only	Measured Primary Bit Error Rate. Non MIMO platforms only.
STR secondaryBERDisplay	1.3.6.1.4.1.161.19.3.2.2.56	DisplayString	read-only	Measured Secondary Bit Error Rate. FSK platforms only.
STR totalBERDisplay	1.3.6.1.4.1.161.19.3.2.2.57	DisplayString	read-only	Measured Total Bit Error Rate. For MIMO this is combined both paths.
INT minRadioDbm	1.3.6.1.4.1.161.19.3.2.2.58	INTEGER	read-only	Maximum receive power of beacon in dBm. For MIMO radios, this is only available in the vertical path.
INT maxRadioDbm	1.3.6.1.4.1.161.19.3.2.2.59	INTEGER	read-only	Maximum receive power of beacon in dBm. For MIMO radios, this is only available in the vertical path.
TIK pppoeSessIdleTime	1.3.6.1.4.1.161.19.3.2.2.60	TimeTicks	read-only	Idle Time of current PPPoE Session in ticks
INT radioDbmAvg	1.3.6.1.4.1.161.19.3.2.2.61	INTEGER	read-only	Average Receive Power of the AP's beacon in dBm. OFDM Radios only. For MIMO this is only the verical path, as the beacon is not transmitted on horizontal.
INT zoltarFPGAFreqOffset	1.3.6.1.4.1.161.19.3.2.2.62	INTEGER	read-only	FPGA peek of 70001088
INT zoltarSWFreqOffset	1.3.6.1.4.1.161.19.3.2.2.63	INTEGER	read-only	FPGA peek of 7000108C
U32 airDelayns	1.3.6.1.4.1.161.19.3.2.2.64	Unsigned32	read-only	Round trip delay in nanoseconds.
INT currentColorCode	1.3.6.1.4.1.161.19.3.2.2.65	INTEGER	read-only	The current Color Code of the Registered AP/BHM. A value of -1 is return when the device is not registered.
INT currentColorCodePri	1.3.6.1.4.1.161.19.3.2.2.66	INTEGER	read-only	The current priority of the Registered color code
U32 currentChanFreq	1.3.6.1.4.1.161.19.3.2.2.67	Unsigned32	read-only	The Current Channel Frequency of the AP/BHM when in session.
STR linkQualityBeacon	1.3.6.1.4.1.161.19.3.2.2.68	DisplayString	read-only	Engineering only. Link Quality for incoming beacons. For Gen II OFDM radios and forward. For PMP450 and forward this is vertical path.
C32 dhcpServerPktXmt	1.3.6.1.4.1.161.19.3.2.2.72	Counter32	read-only	Number of packets transmitted by SM DHCP Server
C32 dhcpServerPktRcv	1.3.6.1.4.1.161.19.3.2.2.73	Counter32	read-only	Number of packets received by SM DHCP Server
C32 dhcpServerPktToss	1.3.6.1.4.1.161.19.3.2.2.74	Counter32	read-only	Number of packets tossed by SM DHCP Server
STR receiveFragmentsModulationPercentage	1.3.6.1.4.1.161.19.3.2.2.86	DisplayString	read-only	Engineering use only. The percentage of recent fragments received at which modulation. For Gen II OFDM only and forward.
C32 fragmentsReceived1XVertical	1.3.6.1.4.1.161.19.3.2.2.87	Counter32	read-only	Engineering use only. Number of fragments received in 1x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.
C32 fragmentsReceived2XVertical	1.3.6.1.4.1.161.19.3.2.2.88	Counter32	read-only	Engineering use only. Number of fragments received in 2x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.
C32 fragmentsReceived3XVertical	1.3.6.1.4.1.161.19.3.2.2.89	Counter32	read-only	Engineering use only. Number of fragments received in 3x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.
C32 fragmentsReceived4XVertical	1.3.6.1.4.1.161.19.3.2.2.90	Counter32	read-only	Engineering use only. Number of fragments received in 4x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path.
STR linkQualityData1XVertical	1.3.6.1.4.1.161.19.3.2.2.91	DisplayString	read-only	Engineering use only. Link Quality for the data VC for QPSK modulation (1X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.
STR linkQualityData2XVertical	1.3.6.1.4.1.161.19.3.2.2.92	DisplayString	read-only	Engineering use only. Link Quality for the data VC for 16-QAM modulation (2X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.
STR linkQualityData3XVertical	1.3.6.1.4.1.161.19.3.2.2.93	DisplayString	read-only	Engineering use only. Link Quality for the data VC for 64-QAM modulation (3X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.
STR linkQualityData4XVertical	1.3.6.1.4.1.161.19.3.2.2.94	DisplayString	read-only	Engineering use only. Link Quality for the data VC for 256-QAM modulation (4X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path.
INT signalToNoiseRatioSMVertical	1.3.6.1.4.1.161.19.3.2.2.95	INTEGER	read-only	An estimated signal to noise ratio based on the last received data. For GenII OFDM only and forward. For MIMO this is the vertical antenna. Will return zero if Signal to Noise Ratio Calculation is disabled.
C32 rfStatTxSuppressionCount	1.3.6.1.4.1.161.19.3.2.2.96	Counter32	read-only	RF Scheduler Stats DFS TX Suppression Count
U32 bridgecbUplinkCreditRate	1.3.6.1.4.1.161.19.3.2.2.97	Unsigned32	read-only	Sustained uplink data rate.
U32 bridgecbUplinkCreditLimit	1.3.6.1.4.1.161.19.3.2.2.98	Unsigned32	read-only	Uplink Burst Allocation.
U32 bridgecbDownlinkCreditRate	1.3.6.1.4.1.161.19.3.2.2.99	Unsigned32	read-only	Sustained uplink data rate.
U32 bridgecbDownlinkCreditLimit	1.3.6.1.4.1.161.19.3.2.2.100	Unsigned32	read-only	Uplink Burst Allocation.
STR mimoQpskBerDisplay	1.3.6.1.4.1.161.19.3.2.2.101	DisplayString	read-only	QPSK BER statistics. MIMO platforms only.
STR mimo16QamBerDisplay	1.3.6.1.4.1.161.19.3.2.2.102	DisplayString	read-only	16-QAM BER statistics MIMO platforms only. Engineering use only.
STR mimo64QamBerDisplay	1.3.6.1.4.1.161.19.3.2.2.103	DisplayString	read-only	64-QAM BER statistics MIMO platforms only. Engineering use only.
STR mimo256QamBerDisplay	1.3.6.1.4.1.161.19.3.2.2.104	DisplayString	read-only	256-QAM BER statistics MIMO platforms only. Engineering use only.
STR mimoBerRcvModulationType	1.3.6.1.4.1.161.19.3.2.2.105	DisplayString	read-only	Receive modulation type. MIMO platforms only.
INT signalToNoiseRatioSMHorizontal	1.3.6.1.4.1.161.19.3.2.2.106	INTEGER	read-only	An estimated signal to noise ratio based on the last received data for horizontal antenna. MIMO radios only. Will return zero if Signal to Noise Ratio Calculation is disabled.
INT maxRadioDbmDeprecated	1.3.6.1.4.1.161.19.3.2.2.107	INTEGER	read-only	This OID was inadvertently moved in 12.0.2. Please use maxRadioDbm. This OID is deprecated and kept for backwards compatibility.
STR signalStrengthRatio	1.3.6.1.4.1.161.19.3.2.2.108	DisplayString	read-only	Signal Strength Ratio in dB is the power received by the vertical antenna input (dB) - power received by the horizontal antenna input (dB). MIMO radios only.
C32 fragmentsReceived1XHorizontal	1.3.6.1.4.1.161.19.3.2.2.109	Counter32	read-only	Engineering use only. Number of fragments received in 1x modulation. For MIMO radios only. For MIMO this is the horizontal path.
C32 fragmentsReceived2XHorizontal	1.3.6.1.4.1.161.19.3.2.2.110	Counter32	read-only	Engineering use only. Number of fragments received in 2x modulation. For MIMO radios only. For MIMO this is the horizontal path.
C32 fragmentsReceived3XHorizontal	1.3.6.1.4.1.161.19.3.2.2.111	Counter32	read-only	Engineering use only. Number of fragments received in 3x modulation. For MIMO radios only. For MIMO this is the horizontal path.
C32 fragmentsReceived4XHorizontal	1.3.6.1.4.1.161.19.3.2.2.112	Counter32	read-only	Engineering use only. Number of fragments received in 4x modulation. For MIMO radios only. For MIMO this is the horizontal path.
STR linkQualityData1XHorizontal	1.3.6.1.4.1.161.19.3.2.2.113	DisplayString	read-only	Engineering use only. Link Quality for the data VC for QPSK modulation (1X). For MIMO radios only. For MIMO this is the horizontal path.
STR linkQualityData2XHorizontal	1.3.6.1.4.1.161.19.3.2.2.114	DisplayString	read-only	Engineering use only. Link Quality for the data VC for 16-QAM modulation (2X). For MIMO radios only. For MIMO this is the horizontal path.
STR linkQualityData3XHorizontal	1.3.6.1.4.1.161.19.3.2.2.115	DisplayString	read-only	Engineering use only. Link Quality for the data VC for 64-QAM modulation (3X). For MIMO radios only. For MIMO this is the horizontal path.
STR linkQualityData4XHorizontal	1.3.6.1.4.1.161.19.3.2.2.116	DisplayString	read-only	Engineering use only. Link Quality for the data VC for 256-QAM modulation (4X). For MIMO radios only. For MIMO this is the horizontal path.
STR radioDbmHorizontal	1.3.6.1.4.1.161.19.3.2.2.117	DisplayString	read-only	Receive power level of the horizontal antenna in dBm. MIMO radios only.
STR radioDbmVertical	1.3.6.1.4.1.161.19.3.2.2.118	DisplayString	read-only	Receive power level of the vertical antenna in dBm. MIMO radios only.
U32 bridgecbDownlinkMaxBurstBitRate	1.3.6.1.4.1.161.19.3.2.2.119	Unsigned32	read-only	Maximum burst downlink rate.
U32 bridgecbUplinkMaxBurstBitRate	1.3.6.1.4.1.161.19.3.2.2.120	Unsigned32	read-only	Maximum burst uplink Rate.
INT currentCyclicPrefix	1.3.6.1.4.1.161.19.3.2.2.121	INTEGER	read-only	The Current Cyclic Prefix of the AP/BHM when in session.
INT currentBandwidth	1.3.6.1.4.1.161.19.3.2.2.122	INTEGER	read-only	The Current Bandwidth of the AP/BHM when in session.
INT berPwrRxFPGAPathA	1.3.6.1.4.1.161.19.3.2.2.123	INTEGER	read-only	BER power level on FPGA Rx Path A of SM.
INT berPwrRxFPGAPathB	1.3.6.1.4.1.161.19.3.2.2.124	INTEGER	read-only	BER power level on FPGA Rx Path B of SM.
INT rawBERPwrRxPathA	1.3.6.1.4.1.161.19.3.2.2.125	INTEGER	read-only	Raw unadjusted BER power level on FPGA Rx Path A of SM.
INT rawBERPwrRxPathB	1.3.6.1.4.1.161.19.3.2.2.126	INTEGER	read-only	Raw unadjusted BER power level on FPGA Rx Path B of SM.
INT radioModeStatus	1.3.6.1.4.1.161.19.3.2.2.127	INTEGER	read-only	The current radio mode that SM is operating in. PMP 430 SMs only. Introduced in release 12.2.
INT adaptRateLowPri	1.3.6.1.4.1.161.19.3.2.2.128	INTEGER	read-only	The current transmitting rate of the low priority VC. 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMO
INT adaptRateHighPri	1.3.6.1.4.1.161.19.3.2.2.129	INTEGER	read-only	The current transmitting rate of the high priority VC. -1 : High Priority Channel not configured 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMO
C64 bitErrorsQSPKpathA	1.3.6.1.4.1.161.19.3.2.2.130	Counter64	read-only	Number of bit errors received from BER packet at QPSK path A. Valid MIMO platforms only.
C64 bitErrorsQSPKpathB	1.3.6.1.4.1.161.19.3.2.2.131	Counter64	read-only	Number of bit errors received from BER packet at QPSK path B. Valid MIMO platforms only.
C64 bitErrors16QAMpathA	1.3.6.1.4.1.161.19.3.2.2.132	Counter64	read-only	Number of bit errors received from BER packet at 16-QAM path A. Valid MIMO platforms only. Engineering use only.
C64 bitErrors16QAMpathB	1.3.6.1.4.1.161.19.3.2.2.133	Counter64	read-only	Number of bit errors received from BER packet at 16-QAM path B. Valid MIMO platforms only. Engineering use only.
C64 bitErrors64QAMpathA	1.3.6.1.4.1.161.19.3.2.2.134	Counter64	read-only	Number of bit errors received from BER packet at 64-QAM path A. Valid MIMO platforms only. Engineering use only.
C64 bitErrors64QAMpathB	1.3.6.1.4.1.161.19.3.2.2.135	Counter64	read-only	Number of bit errors received from BER packet at 64-QAM path B. Valid MIMO platforms only. Engineering use only.
C64 bitErrors256QAMpathA	1.3.6.1.4.1.161.19.3.2.2.136	Counter64	read-only	Number of bit errors received from BER packet at 256-QAM path A. Valid MIMO platforms only. Engineering use only.
C64 bitErrors256QAMpathB	1.3.6.1.4.1.161.19.3.2.2.137	Counter64	read-only	Number of bit errors received from BER packet at 256-QAM path B. Valid MIMO platforms only. Engineering use only.
C64 bitsReceivedPerPathModulation	1.3.6.1.4.1.161.19.3.2.2.138	Counter64	read-only	Number of bit received from BER. To calculate Bit Error Rate, take bit errors at a modulation and path and divide by this OID. To get combined BER add errors and divide by this multiplied by each path and modulation. i.e. MIMO QPSK combined BER = ((errors on path A) + (errors on path B))/(bits recieved per path modulation * 2) Valid MIMO platforms only.
whispSmGroups	1.3.6.1.4.1.161.19.3.2.3
whispSmConfigGroup	1.3.6.1.4.1.161.19.3.2.3.1			Canopy Subscriber Module configuration group.
whispSmStatusGroup	1.3.6.1.4.1.161.19.3.2.3.2			Canopy Subscriber Module status group.
whispSmNotifGroup	1.3.6.1.4.1.161.19.3.2.3.3			WHiSP SMs notification group.
whispMappingTableGroup	1.3.6.1.4.1.161.19.3.2.3.4			Canopy SM NAT port mapping Table group.
whispSmEvent	1.3.6.1.4.1.161.19.3.2.4
whispSmDfsEvent	1.3.6.1.4.1.161.19.3.2.4.1
NTF whispRadarDetected	1.3.6.1.4.1.161.19.3.2.4.1.1			Radar detected transmit stopped.
NTF whispRadarEnd	1.3.6.1.4.1.161.19.3.2.4.1.2			Radar ended back to normal transmit.
whispSmSpAnEvent	1.3.6.1.4.1.161.19.3.2.4.2
NTF enterSpectrumAnalysis	1.3.6.1.4.1.161.19.3.2.4.2.1			Entering spectrum analysis. physAddress - MAC address of the SM
NTF availableSpectrumAnalysis	1.3.6.1.4.1.161.19.3.2.4.2.2			Spectrum analysis is complete, SM is re-registered with AP and results are available. physAddress - MAC address of the SM
whispSmDHCPClientEvent	1.3.6.1.4.1.161.19.3.2.4.3
NTF smNatWanDHCPClientEvent	1.3.6.1.4.1.161.19.3.2.4.3.1			NAT WAN DHCP Client has received a new address via DHCP.
NTF smNatRFPubDHCPClientEvent	1.3.6.1.4.1.161.19.3.2.4.3.2			NAT RF Public DHCP Client has received a new address via DHCP.
whispMappingTable	1.3.6.1.4.1.161.19.3.2.5		not-accessible	NAT port mapping information table.
whispMappingEntry	1.3.6.1.4.1.161.19.3.2.5.1		not-accessible	Mapping table entry.
INT tableIndex	1.3.6.1.4.1.161.19.3.2.5.1.1	INTEGER	read-only	User information table index.
INT protocol	1.3.6.1.4.1.161.19.3.2.5.1.2	INTEGER	read-write	Protocol type: 0:both UDP and TCP, 1:UDP, 2:TCP.
INT port	1.3.6.1.4.1.161.19.3.2.5.1.3	INTEGER	read-write	Application port number. e.g. 23=telnet, 21=ftp etc. Should be a positive integer.
IP localIp	1.3.6.1.4.1.161.19.3.2.5.1.4	IpAddress	read-write	IP of local host to which the incoming packet mapped to an application should be forwarded.
whispSmTranslationTable	1.3.6.1.4.1.161.19.3.2.6		not-accessible	Translation Table.
whispSmTranslationTableEntry	1.3.6.1.4.1.161.19.3.2.6.1		not-accessible	Translation Table Entry.
INT whispTranslationTableIndex	1.3.6.1.4.1.161.19.3.2.6.1.1	INTEGER	read-only	Index into translation table.
MAC whispTranslationTableMacAddr	1.3.6.1.4.1.161.19.3.2.6.1.2	MacAddress	read-only	MAC Address of the registered enity.
IP whispTranslationTableIpAddr	1.3.6.1.4.1.161.19.3.2.6.1.3	IpAddress	read-only	Ip Address of the registered entity.
C32 whispTranslationTableAge	1.3.6.1.4.1.161.19.3.2.6.1.4	Counter32	read-only	Age of the registered entity.
whispSmSecurity	1.3.6.1.4.1.161.19.3.2.7
certTable	1.3.6.1.4.1.161.19.3.2.7.1		not-accessible	The table of CA Certificates on SM.
certEntry	1.3.6.1.4.1.161.19.3.2.7.1.1		not-accessible	Entry of Certifcates.
INT certIndex	1.3.6.1.4.1.161.19.3.2.7.1.1.1	INTEGER	read-only	User information table index.
INT cert	1.3.6.1.4.1.161.19.3.2.7.1.1.2	INTEGER	read-only	0: Inactive 1: Active
INT action	1.3.6.1.4.1.161.19.3.2.7.1.1.3	INTEGER	read-write	0: No Operation 1: Delete Certificate
STR certificateDN	1.3.6.1.4.1.161.19.3.2.7.1.1.4	DisplayString	read-only	Distinguished Name of Certificate 2
INT numAuthCerts	1.3.6.1.4.1.161.19.3.2.7.2	INTEGER	read-only	can have a max value of 2
INT authenticationEnforce	1.3.6.1.4.1.161.19.3.2.7.3	INTEGER	read-write	enforce SM to register with specifed Auth Enabled AP
INT phase1	1.3.6.1.4.1.161.19.3.2.7.4	INTEGER	read-write	Select the outer method for EAP Authentication
INT phase2	1.3.6.1.4.1.161.19.3.2.7.5	INTEGER	read-write	Select the outer method for EAP Authentication
OCT authOuterId	1.3.6.1.4.1.161.19.3.2.7.6	OCTET STRING	read-write	EAP Peer Username
STR authPassword	1.3.6.1.4.1.161.19.3.2.7.7	DisplayString	read-write	EAP Peer password
STR authUsername	1.3.6.1.4.1.161.19.3.2.7.8	DisplayString	read-write	EAP Peer Identity
INT useRealm	1.3.6.1.4.1.161.19.3.2.7.9	INTEGER	read-write	Enable or disable the use of realm option.
STR realm	1.3.6.1.4.1.161.19.3.2.7.10	DisplayString	read-write	EAP Peer Realm
whispSmControls	1.3.6.1.4.1.161.19.3.2.8
INT clearLinkStats	1.3.6.1.4.1.161.19.3.2.8.1	INTEGER	read-write	Setting this to a nonzero value will clear the link stats.

RFC description

Whisp wireless systems management MIB; defines management objects for wireless access point and controller systems in Whisp networks.

Start monitoring Cambium/Motorola Canopy Subscriber Module (SM), fixed wireless broadband CPE radio (signal-level/session/DFS-event status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download WHISP-SM-MIB