All MIBs › WHISP-BOX-MIBV2-MIB
Organization: Cambium Networks
Last Updated: 2003-04-15
Category: Cambium/Motorola Wireless Broadband
Description: Manages Cambium Networks Canopy wireless broadband radio hardware status, link metrics, and configuration parameters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is WHISP-BOX-MIBV2-MIB?
WHISP-BOX-MIBV2-MIB is a Cambium Networks (Motorola Canopy/WHISP fixed-wireless heritage, built on WHISP-GLOBAL-REG-MIB/WHISP-TCV2-MIB) proprietary MIB reporting generic box-level status for Canopy radios. Its objects cover software/FPGA version, ESN, boot info, box temperature/device type/encryption, Ethernet link status, RF frequency, platform version/type, DHCP LAN/RF-public IP/subnet/gateway settings, LAN/RF-public DHCP status, in-sync/out-of-sync counts, PLL-out-lock count, TX-calibration-failure flag, and software version. As a status/configuration MIB it lets an administrator confirm RF sync status and network provisioning on a Cambium (Motorola Canopy) fixed-wireless radio. It is deployed on Cambium Networks Canopy fixed-wireless radios. Engineers can download the WHISP-BOX-MIBV2-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in WHISP-BOX-MIBV2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Cambium Networks Canopy fixed-wireless radios
Monitoring Examples
An administrator checks inSyncCount and boxTemperature to confirm RF synchronization and thermal health on a Cambium Networks Canopy radio.
What Can Be Monitored
- RF synchronization status and box-level hardware health
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-CONF
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Gauge32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress |
From WHISP-GLOBAL-REG-MIB
| whispBox | OBJECT-IDENTITY |
| whispModules | OBJECT-IDENTITY |
From WHISP-TCV2-MIB
| EventString | |
| WhispLUID | |
| WhispMACAddress |
How to Use in IPNetwork Monitor
Example using packetOverloadCounter OID:
Select a Cambium Networks Canopy fixed-wireless radio (RF sync/temperature/network-provisioning status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type packetOverloadCounter into the Find box to locate it in the OID tree, then select it and click OK. It reports the total packet overload count. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| whispBoxLevelMibModule | 1.3.6.1.4.1.161.19.1.1.8 | This module contains generic Box-Level MIB definitions for Canopy Radios. | ||
| whispBoxStatus | 1.3.6.1.4.1.161.19.3.3.1 | |||
| STR whispBoxSoftwareVer | 1.3.6.1.4.1.161.19.3.3.1.1 | DisplayString | read-only | Version of software. Should be noted in the event customer has technical difficulties and need to contact technical support. |
| STR whispBoxFPGAVer | 1.3.6.1.4.1.161.19.3.3.1.2 | DisplayString | read-only | Version of FPGA. |
| STR whispBoxEsn | 1.3.6.1.4.1.161.19.3.3.1.3 | DisplayString | read-only | Electronic serial number(MAC address) assigned to Radio. |
| STR whispBoxBoot | 1.3.6.1.4.1.161.19.3.3.1.4 | DisplayString | read-only | Software boot version. |
| STR boxTemperature | 1.3.6.1.4.1.161.19.3.3.1.5 | DisplayString | read-only | Radio temperature. |
| STR boxDeviceType | 1.3.6.1.4.1.161.19.3.3.1.6 | DisplayString | read-only | The type of the device. |
| STR boxDeviceTypeID | 1.3.6.1.4.1.161.19.3.3.1.7 | DisplayString | read-only | Device type ID. |
| STR boxEncryption | 1.3.6.1.4.1.161.19.3.3.1.8 | DisplayString | read-only | Device encryption type. |
| STR etherLinkStatus | 1.3.6.1.4.1.161.19.3.3.1.9 | DisplayString | read-only | Ethernet link status. |
| STR boxFrequency | 1.3.6.1.4.1.161.19.3.3.1.10 | DisplayString | read-only | Frequency band of the device. |
| INT platformVer | 1.3.6.1.4.1.161.19.3.3.1.11 | INTEGER | read-only | Hardware platform version. For internal use. |
| STR platformType | 1.3.6.1.4.1.161.19.3.3.1.12 | DisplayString | read-only | Platform type: Canopy, Canopy Lite, Canopy Lite - Advantage, Advantage, Russian, Russian - Advantage. |
| IP dhcpLanIp | 1.3.6.1.4.1.161.19.3.3.1.13 | IpAddress | read-only | LAN interface IP obtained through DHCP. |
| IP dhcpLanSubnetMask | 1.3.6.1.4.1.161.19.3.3.1.14 | IpAddress | read-only | LAN interface Subnet Mask obtained through DHCP. |
| IP dhcpLanGateway | 1.3.6.1.4.1.161.19.3.3.1.15 | IpAddress | read-only | LAN interface Gateway obtained through DHCP. |
| IP dhcpRfPublicIp | 1.3.6.1.4.1.161.19.3.3.1.16 | IpAddress | read-only | RF Public interface IP obtained through DHCP. |
| IP dhcpRfPublicSubnetMask | 1.3.6.1.4.1.161.19.3.3.1.17 | IpAddress | read-only | RF Public interface Subnet Mask obtained through DHCP. |
| IP dhcpRfPublicGateway | 1.3.6.1.4.1.161.19.3.3.1.18 | IpAddress | read-only | RF Public interface Gateway obtained through DHCP. |
| STR lanDhcpStatus | 1.3.6.1.4.1.161.19.3.3.1.19 | DisplayString | read-only | Display LAN interface current DHPC status. |
| STR rfPublicDhcpStatus | 1.3.6.1.4.1.161.19.3.3.1.20 | DisplayString | read-only | Display RF Public interface current DHPC status. |
| INT inSyncCount | 1.3.6.1.4.1.161.19.3.3.1.21 | INTEGER | read-only | Counter for number of In Synchronization. |
| INT outSyncCount | 1.3.6.1.4.1.161.19.3.3.1.22 | INTEGER | read-only | Counter for number of Out of Synchronization. |
| INT pllOutLockCount | 1.3.6.1.4.1.161.19.3.3.1.23 | INTEGER | read-only | Counter for number of PLL out of Lock. |
| INT txCalFailure | 1.3.6.1.4.1.161.19.3.3.1.24 | INTEGER | read-only | Counter for number of TX Calibration failure. |
| STR swVersion | 1.3.6.1.4.1.161.19.3.3.1.25 | DisplayString | read-only | Software version information. |
| STR pldVersion | 1.3.6.1.4.1.161.19.3.3.1.26 | DisplayString | read-only | PLD version information. |
| STR platformInfo | 1.3.6.1.4.1.161.19.3.3.1.27 | DisplayString | read-only | Platform information. |
| STR antPolarization | 1.3.6.1.4.1.161.19.3.3.1.28 | DisplayString | read-only | Antenna polarization for FSK radios. |
| C32 packetOverloadCounterEx | 1.3.6.1.4.1.161.19.3.3.1.29 | Counter32 | read-only | Total packet overload count. |
| STR whispBoxP11Personality | 1.3.6.1.4.1.161.19.3.3.1.30 | DisplayString | read-only | Board Personality Configuration of P11 and P12 radios. |
| STR whispBoxP11FPGAType | 1.3.6.1.4.1.161.19.3.3.1.31 | DisplayString | read-only | FPGA Type on P11 and P12 radios. |
| STR whispBoxP11BstrapFPGAVer | 1.3.6.1.4.1.161.19.3.3.1.32 | DisplayString | read-only | P11 Bootstrap FPGA Version. |
| C32 numDFSDetections | 1.3.6.1.4.1.161.19.3.3.1.33 | Counter32 | read-only | Number of DFS/LBT Detections since last boot. |
| C32 rxOverrunPkts | 1.3.6.1.4.1.161.19.3.3.1.34 | Counter32 | read-only | Counter for number of received overrun packets error. |
| INT boxTemperatureC | 1.3.6.1.4.1.161.19.3.3.1.35 | INTEGER | read-only | Radio temperature in Celsius. |
| INT boxTemperatureF | 1.3.6.1.4.1.161.19.3.3.1.36 | INTEGER | read-only | Radio temperature in Fahrenheit. |
| C32 bridgeCbFecStatbin | 1.3.6.1.4.1.161.19.3.3.1.37 | Counter32 | read-only | Bridge CB FEC Stats bin |
| C32 bridgeCbFecStatbout | 1.3.6.1.4.1.161.19.3.3.1.38 | Counter32 | read-only | Bridge CB FEC Stats bout |
| C32 bridgeCbFecStatbtoss | 1.3.6.1.4.1.161.19.3.3.1.39 | Counter32 | read-only | Bridge CB FEC Stats btoss |
| C32 bridgeCbFecStatbtosscap | 1.3.6.1.4.1.161.19.3.3.1.40 | Counter32 | read-only | Bridge CB FEC Stats btosscap |
| C32 bridgeCbFecStatuin | 1.3.6.1.4.1.161.19.3.3.1.41 | Counter32 | read-only | Bridge CB FEC Stats uin |
| C32 bridgeCbFecStatuout | 1.3.6.1.4.1.161.19.3.3.1.42 | Counter32 | read-only | Bridge CB FEC Stats uout |
| C32 bridgeCbFecStatutoss | 1.3.6.1.4.1.161.19.3.3.1.43 | Counter32 | read-only | Bridge CB FEC Stats utoss |
| C32 bridgeCbFecStatutosscap | 1.3.6.1.4.1.161.19.3.3.1.44 | Counter32 | read-only | Bridge CB FEC Stats utosscap |
| C32 bridgeCbRFStatbin | 1.3.6.1.4.1.161.19.3.3.1.45 | Counter32 | read-only | Bridge CB RF Stats bin |
| C32 bridgeCbRFStatbout | 1.3.6.1.4.1.161.19.3.3.1.46 | Counter32 | read-only | Bridge CB RF Stats bout |
| C32 bridgeCbRFStatbtoss | 1.3.6.1.4.1.161.19.3.3.1.47 | Counter32 | read-only | Bridge CB RF Stats btoss |
| C32 bridgeCbRFStatbtosscap | 1.3.6.1.4.1.161.19.3.3.1.48 | Counter32 | read-only | Bridge CB RF Stats btosscap |
| C32 bridgeCbRFStatuin | 1.3.6.1.4.1.161.19.3.3.1.49 | Counter32 | read-only | Bridge CB RF Stats uin |
| C32 bridgeCbRFStatuout | 1.3.6.1.4.1.161.19.3.3.1.50 | Counter32 | read-only | Bridge CB RF Stats uout |
| C32 bridgeCbRFStatutoss | 1.3.6.1.4.1.161.19.3.3.1.51 | Counter32 | read-only | Bridge CB RF Stats utoss |
| C32 bridgeCbRFStatutosscap | 1.3.6.1.4.1.161.19.3.3.1.52 | Counter32 | read-only | Bridge CB RF Stats utosscap |
| C32 bridgeCbErrStatNI1QSend | 1.3.6.1.4.1.161.19.3.3.1.53 | Counter32 | read-only | Bridge CB Error Stats ErrNI1QSend |
| C32 bridgeCbErrStatNI2QSend | 1.3.6.1.4.1.161.19.3.3.1.54 | Counter32 | read-only | Bridge CB Error Stats ErrNI2QSend |
| C32 bridgeCbErrStatBridgeFull | 1.3.6.1.4.1.161.19.3.3.1.55 | Counter32 | read-only | Bridge CB Error Stats BridgeFull |
| C32 bridgeCbErrStatSendMsg | 1.3.6.1.4.1.161.19.3.3.1.56 | Counter32 | read-only | Bridge CB Error Stats SendMsg |
| C32 bridgeCbErrStatAPFecQSend | 1.3.6.1.4.1.161.19.3.3.1.57 | Counter32 | read-only | Bridge CB Error Stats APFecQSend |
| C32 bridgeCbErrStatApRfQSend | 1.3.6.1.4.1.161.19.3.3.1.58 | Counter32 | read-only | Bridge CB Error Stats ApRfQSend |
| C32 rfStatXmtUDataCnt | 1.3.6.1.4.1.161.19.3.3.1.59 | Counter32 | read-only | RF Scheduler Stats Transmit Unicast Data Count |
| C32 rfStatXmtBDataCnt | 1.3.6.1.4.1.161.19.3.3.1.60 | Counter32 | read-only | RF Scheduler Stats Transmit Broadcast Data Count |
| C32 rfStatRcvUDataCnt | 1.3.6.1.4.1.161.19.3.3.1.61 | Counter32 | read-only | RF Scheduler Stats Receive Unicast Data Count |
| C32 rfStatRcvBDataCnt | 1.3.6.1.4.1.161.19.3.3.1.62 | Counter32 | read-only | RF Scheduler Stats Receive Broadcast Data Count |
| C32 rfStatXmtCntlCnt | 1.3.6.1.4.1.161.19.3.3.1.63 | Counter32 | read-only | RF Scheduler Stats Transmit Control Count |
| C32 rfStatRcvCntlCnt | 1.3.6.1.4.1.161.19.3.3.1.64 | Counter32 | read-only | RF Scheduler Stats Receive Control Count |
| C32 rfStatInSyncCount | 1.3.6.1.4.1.161.19.3.3.1.65 | Counter32 | read-only | RF Scheduler Stats In Sync Count |
| C32 rfStatOutSyncCount | 1.3.6.1.4.1.161.19.3.3.1.66 | Counter32 | read-only | RF Scheduler Stats Out Sync Count |
| C32 rfStatOverrunCount | 1.3.6.1.4.1.161.19.3.3.1.67 | Counter32 | read-only | RF Scheduler Stats Overrun Count |
| C32 rfStatUnderrunCount | 1.3.6.1.4.1.161.19.3.3.1.68 | Counter32 | read-only | RF Scheduler Stats Underrun Count |
| C32 rfStatRcvCorruptDataCount | 1.3.6.1.4.1.161.19.3.3.1.69 | Counter32 | read-only | RF Scheduler Stats Receive Corrupt Data Count |
| C32 rfStatBadBcastCtlCnt | 1.3.6.1.4.1.161.19.3.3.1.70 | Counter32 | read-only | RF Scheduler Stats Bad Broadcast Control Count |
| C32 rfStatPLLOutOfLockCnt | 1.3.6.1.4.1.161.19.3.3.1.71 | Counter32 | read-only | RF Scheduler Stats PLL Out of Lock Count |
| C32 rfStatBeaconVerMismatchCnt | 1.3.6.1.4.1.161.19.3.3.1.72 | Counter32 | read-only | RF Scheduler Stats Beacon version Mismatch Count |
| C32 rfStatBadFreqBcnRcvCnt | 1.3.6.1.4.1.161.19.3.3.1.73 | Counter32 | read-only | RF Scheduler Stats Wrong Frequency Beacon Received Count |
| C32 rfStatnonLiteBcnRcvCnt | 1.3.6.1.4.1.161.19.3.3.1.74 | Counter32 | read-only | RF Scheduler Stats Non Lite Beacon Received Count |
| C32 rfStatUnsupFeatBcnRcvCnt | 1.3.6.1.4.1.161.19.3.3.1.75 | Counter32 | read-only | RF Scheduler Stats Unsupported Feature Beacon Received Count |
| C32 rfStatUnkwnFeatBcnRcvCnt | 1.3.6.1.4.1.161.19.3.3.1.76 | Counter32 | read-only | RF Scheduler Stats Unknown Feature Beacon Received Count |
| C32 rfStatTxCalFailCnt | 1.3.6.1.4.1.161.19.3.3.1.77 | Counter32 | read-only | RF Scheduler Stats TX Calibration Failures Count |
| C32 rfStatBadInSyncIDRcv | 1.3.6.1.4.1.161.19.3.3.1.78 | Counter32 | read-only | RF Scheduler Stats Bad In Sync ID Received Count |
| C32 rfStatTempOutOfRange | 1.3.6.1.4.1.161.19.3.3.1.79 | Counter32 | read-only | RF Scheduler Stats Temperature Out of Range Count |
| C32 rfStatRSSIOutOfRange | 1.3.6.1.4.1.161.19.3.3.1.80 | Counter32 | read-only | RF Scheduler Stats RSSI Out of Range Count |
| C32 rfStatRangeCapEnf | 1.3.6.1.4.1.161.19.3.3.1.81 | Counter32 | read-only | RF Scheduler Stats Range Cap Enforced Count |
| C32 rfStatRcvLTStart | 1.3.6.1.4.1.161.19.3.3.1.82 | Counter32 | read-only | RF Scheduler Stats Rcv LT Start Count |
| C32 rfStatRcvLTStartHS | 1.3.6.1.4.1.161.19.3.3.1.83 | Counter32 | read-only | RF Scheduler Stats Rcv LT Start HS Count |
| C32 rfStatRcvLTResult | 1.3.6.1.4.1.161.19.3.3.1.84 | Counter32 | read-only | RF Scheduler Stats Rcv LT Result Count |
| C32 rfStatXmtLTResult | 1.3.6.1.4.1.161.19.3.3.1.85 | Counter32 | read-only | RF Scheduler Stats Xmt LT Result Count |
| STR whispFeatureKeyOrigin | 1.3.6.1.4.1.161.19.3.3.1.86 | DisplayString | read-only | Origin of Feature Key which includes GMT time and location of the Key programming (if time is 0 the key was converted locally) |
| STR radioMSN | 1.3.6.1.4.1.161.19.3.3.1.87 | DisplayString | read-only | MSN of the radio. |
| INT updateStatus | 1.3.6.1.4.1.161.19.3.3.1.88 | INTEGER | read-only | Current Status of Device Update |
| INT syslogStatTxSuccesses | 1.3.6.1.4.1.161.19.3.3.1.89 | INTEGER | read-only | The count of Syslog messages sent to UDP layer. |
| INT syslogStatDropped | 1.3.6.1.4.1.161.19.3.3.1.90 | INTEGER | read-only | Number of dropped syslog messages due to device overload and/or resource limitations. |
| C32 fecStatLinkLost | 1.3.6.1.4.1.161.19.3.3.1.91 | Counter32 | read-only | Ethernet link lost count |
| C32 fecStatLinkDetected | 1.3.6.1.4.1.161.19.3.3.1.92 | Counter32 | read-only | Ethernet link detected count |
| STR natDhcpStatus | 1.3.6.1.4.1.161.19.3.3.1.93 | DisplayString | read-only | Display NAT Public interface current DHPC status. |
| U32 fecInDiscardsCount | 1.3.6.1.4.1.161.19.3.3.1.94 | Unsigned32 | read-only | Ethernet in discards count. |
| U32 fecInErrorsCount | 1.3.6.1.4.1.161.19.3.3.1.95 | Unsigned32 | read-only | Ethernet in errors count. |
| U32 fecOutDiscardsCount | 1.3.6.1.4.1.161.19.3.3.1.96 | Unsigned32 | read-only | Ethernet out discards count. |
| U32 fecOutErrorsCount | 1.3.6.1.4.1.161.19.3.3.1.97 | Unsigned32 | read-only | Ethernet out errors count. |
| U32 rfInDiscardsCount | 1.3.6.1.4.1.161.19.3.3.1.98 | Unsigned32 | read-only | RF in discards count. |
| U32 rfInErrorsCount | 1.3.6.1.4.1.161.19.3.3.1.99 | Unsigned32 | read-only | RF in errors count. |
| U32 rfOutDiscardsCount | 1.3.6.1.4.1.161.19.3.3.1.100 | Unsigned32 | read-only | RF out discards count. |
| U32 rfOutErrorsCount | 1.3.6.1.4.1.161.19.3.3.1.101 | Unsigned32 | read-only | RF out errors count. |
| C32 fecInDiscardsOverloadCount | 1.3.6.1.4.1.161.19.3.3.1.102 | Counter32 | read-only | Ethernet in discards overload. |
| C32 fecOutDiscardsOverloadCount | 1.3.6.1.4.1.161.19.3.3.1.103 | Counter32 | read-only | Ethernet out discards overload. |
| C32 rfInDiscardsOverloadCount | 1.3.6.1.4.1.161.19.3.3.1.104 | Counter32 | read-only | Rf in discards overload. |
| C32 rfOutDiscardsOverloadCount | 1.3.6.1.4.1.161.19.3.3.1.105 | Counter32 | read-only | Rf out discards overload. |
| STR fpgaCompileInfo | 1.3.6.1.4.1.161.19.3.3.1.106 | DisplayString | read-only | Display the fpga compiled attributes. (Engineering Only) |
| STR fpgaBuildDate | 1.3.6.1.4.1.161.19.3.3.1.107 | DisplayString | read-only | Display the entire fpga build date string. (Engineering Only) |
| INT aggregateBandwidthCap | 1.3.6.1.4.1.161.19.3.3.1.108 | INTEGER | read-only | The maximum aggregate (uplink + downlink) the radio is capable of. |
| INT calibrationStatusBool | 1.3.6.1.4.1.161.19.3.3.1.109 | INTEGER | read-only | Boolean OID to show if device is calibrated. Applicable to FSK and MIMO radios only. |
| STR calibrationStatusBox | 1.3.6.1.4.1.161.19.3.3.1.110 | DisplayString | read-only | String to show if radio is calibrated. Applicable to FSK and MIMO radios only. |
| INT radioEngKeyed | 1.3.6.1.4.1.161.19.3.3.1.111 | INTEGER | read-only | This will be set either as 0 if the engineering key patch is not applied to the radio or 1 if it is applied. |
| C32 bridgeCbFecStatfloods | 1.3.6.1.4.1.161.19.3.3.1.112 | Counter32 | read-only | Bridge CB RF Stats Floods (Multipoint AP only) |
| C32 bridgeCbRFStatfloods | 1.3.6.1.4.1.161.19.3.3.1.113 | Counter32 | read-only | Bridge CB RF Stats Floods (Multipoint AP only) |
| INT agcGainRxCH1 | 1.3.6.1.4.1.161.19.3.3.1.114 | INTEGER | read-only | Rcv Gain on Catalina Rx CH1 of SM. |
| INT agcGainRxCH2 | 1.3.6.1.4.1.161.19.3.3.1.115 | INTEGER | read-only | Rcv Gain on Catalina Rx CH2 of SM. |
| INT antType | 1.3.6.1.4.1.161.19.3.3.1.116 | INTEGER | read-only | Indicates whether the antenna is integrated or external (connectorized). |
| C32 rfStatRcvCorruptControlCount | 1.3.6.1.4.1.161.19.3.3.1.117 | Counter32 | read-only | RF Scheduler Stats Receive Corrupt Control Data Count |
| C32 rfStatXmtMDataCnt | 1.3.6.1.4.1.161.19.3.3.1.217 | Counter32 | read-only | RF Scheduler Stats Transmit Multicast Data Count |
| C32 rfStatRcvMDataCnt | 1.3.6.1.4.1.161.19.3.3.1.218 | Counter32 | read-only | RF Scheduler Stats Receive Multicast Data Count |
| whispBoxConfig | 1.3.6.1.4.1.161.19.3.3.2 | |||
| STR linkNegoSpeed | 1.3.6.1.4.1.161.19.3.3.2.1 | DisplayString | read-write | Link negotiation speeds. H10BT -- 10 Base T Half Duplex, F10BT -- 10 Base T Full Duplex, H100BT -- 100 Base T Half Duplex, F100BT -- 100 Base T Full Duplex. Separate the values with comma when doing a set. e.g. H10BT,F10BT,H100BT,F100BT |
| INT colorCode | 1.3.6.1.4.1.161.19.3.3.2.2 | INTEGER | read-write | Color code. |
| STR displayOnlyAccess | 1.3.6.1.4.1.161.19.3.3.2.3 | DisplayString | read-write | This variable is deprecated. |
| STR fullAccess | 1.3.6.1.4.1.161.19.3.3.2.4 | DisplayString | read-write | Full access password. |
| INT webAutoUpdate | 1.3.6.1.4.1.161.19.3.3.2.5 | INTEGER | read-write | Web page auto update in seconds. 0 means disabled. |
| STR pass1Status | 1.3.6.1.4.1.161.19.3.3.2.6 | DisplayString | read-only | Password 1(display only) status. |
| STR pass2Status | 1.3.6.1.4.1.161.19.3.3.2.7 | DisplayString | read-only | Password 2(full access) status. |
| INT bridgeEntryTimeout | 1.3.6.1.4.1.161.19.3.3.2.8 | INTEGER | read-write | Bridge table time out Range : 25 -- 1440 Minutes. |
| INT snmpMibPerm | 1.3.6.1.4.1.161.19.3.3.2.9 | INTEGER | read-write | Read/Write permission for MIB groups. |
| INT bhTimingMode | 1.3.6.1.4.1.161.19.3.3.2.10 | INTEGER | read-write | Variable to switch between Timing Master and Timing Slave. For Backhaul units only. |
| INT bhModulation | 1.3.6.1.4.1.161.19.3.3.2.11 | INTEGER | read-write | Modulation scheme. For Backhaul units only. Only level 4 backhaul can be changed to 20Mbits/Second. |
| INT powerControl | 1.3.6.1.4.1.161.19.3.3.2.12 | INTEGER | read-write | Power control. |
| INT extFilterDelay | 1.3.6.1.4.1.161.19.3.3.2.13 | INTEGER | read-write | External Filters Delay. For 900MHz radios only. |
| INT antennaGain | 1.3.6.1.4.1.161.19.3.3.2.14 | INTEGER | read-write | External Antenna Gain. For radios that uses an external antenna or the DFS feature. |
| INT eirp | 1.3.6.1.4.1.161.19.3.3.2.15 | INTEGER | read-write | This variable is deprecated. |
| INT dynamicLearning | 1.3.6.1.4.1.161.19.3.3.2.16 | INTEGER | read-write | To enable VLAN dynamic learning. |
| INT managementVID | 1.3.6.1.4.1.161.19.3.3.2.17 | INTEGER | read-write | Management VLAN VID. |
| INT agingTimeout | 1.3.6.1.4.1.161.19.3.3.2.18 | INTEGER | read-write | Aging timeout. |
| INT frameType | 1.3.6.1.4.1.161.19.3.3.2.19 | INTEGER | read-write | Allow only tagged frame. |
| INT addVlanMember | 1.3.6.1.4.1.161.19.3.3.2.20 | INTEGER | read-write | Add VLAN memeber. |
| INT removeVlanMember | 1.3.6.1.4.1.161.19.3.3.2.21 | INTEGER | read-write | Remove VLAN memeber. |
| INT scheduling | 1.3.6.1.4.1.161.19.3.3.2.22 | INTEGER | read-write | To use hardware or software scheduling |
| INT transmitterOP | 1.3.6.1.4.1.161.19.3.3.2.23 | INTEGER | read-write | Transmitter output power. This is not available on OFDM SMs. |
| INT bridgeEnable | 1.3.6.1.4.1.161.19.3.3.2.24 | INTEGER | read-write | Disable or enable bridging functionality for a BH unit. |
| INT fecEnable | 1.3.6.1.4.1.161.19.3.3.2.25 | INTEGER | read-write | Disable or enable FEC error correction functionality for multipoint units. |
| IP trapIP1 | 1.3.6.1.4.1.161.19.3.3.2.26 | IpAddress | read-write | Obsoleted. Configure with whispBoxDNS.trap1. |
| IP trapIP2 | 1.3.6.1.4.1.161.19.3.3.2.27 | IpAddress | read-write | Obsoleted. Configure with whispBoxDNS.trap2. |
| IP trapIP3 | 1.3.6.1.4.1.161.19.3.3.2.28 | IpAddress | read-write | Obsoleted. Configure with whispBoxDNS.trap3. |
| IP trapIP4 | 1.3.6.1.4.1.161.19.3.3.2.29 | IpAddress | read-write | Obsoleted. Configure with whispBoxDNS.trap4. |
| IP trapIP5 | 1.3.6.1.4.1.161.19.3.3.2.30 | IpAddress | read-write | Obsoleted. Configure with whispBoxDNS.trap5. |
| IP trapIP6 | 1.3.6.1.4.1.161.19.3.3.2.31 | IpAddress | read-write | Obsoleted. Configure with whispBoxDNS.trap6. |
| IP trapIP7 | 1.3.6.1.4.1.161.19.3.3.2.32 | IpAddress | read-write | Obsoleted. Configure with whispBoxDNS.trap7. |
| IP trapIP8 | 1.3.6.1.4.1.161.19.3.3.2.33 | IpAddress | read-write | Obsoleted. Configure with whispBoxDNS.trap8. |
| IP trapIP9 | 1.3.6.1.4.1.161.19.3.3.2.34 | IpAddress | read-write | Obsoleted. Configure with whispBoxDNS.trap9. |
| IP trapIP10 | 1.3.6.1.4.1.161.19.3.3.2.35 | IpAddress | read-write | Obsoleted. Configure with whispBoxDNS.trap10. |
| STR commStringRWrite | 1.3.6.1.4.1.161.19.3.3.2.36 | DisplayString | read-write | Read/Write Community string. This is a write-only OID. |
| INT subnetMask | 1.3.6.1.4.1.161.19.3.3.2.37 | INTEGER | read-write | Subnet mask for the management IP 1. |
| IP mngtIP | 1.3.6.1.4.1.161.19.3.3.2.38 | IpAddress | read-write | Management IP address 1. |
| INT allowVIDAccess | 1.3.6.1.4.1.161.19.3.3.2.39 | INTEGER | read-write | Allow or disallow local SM management VID access. |
| INT setDefaultPlug | 1.3.6.1.4.1.161.19.3.3.2.40 | INTEGER | read-write | If enable parameters are set to Factory Defaults upon default plug detection. |
| INT hwsCompatibility | 1.3.6.1.4.1.161.19.3.3.2.41 | INTEGER | read-write | If enable, it ensures 6.0 compatibility with HWS. |
| INT gpsInput | 1.3.6.1.4.1.161.19.3.3.2.42 | INTEGER | read-write | Values 1, 2, 3 have been deprecated. (0) Generate AP sync signal. (1) Deprecated. Sync AP to received signal (Timing Port/UGPS). It will set AutoSync. (2) Deprecated. Sync AP to received signal (Power Port). It will set AutoSync plus Free Run. (3) Deprecated. Sync AP using iGPS (Only on devices which support it). It will set AutoSync plus Free Run. (4) AutoSync. (5) AutoSync plus Free Run. |
| INT ism | 1.3.6.1.4.1.161.19.3.3.2.43 | INTEGER | read-write | Enable ISM on 5.7GHz frequency band radios. |
| INT hiPriority | 1.3.6.1.4.1.161.19.3.3.2.44 | INTEGER | read-write | Enable Hi Priority Data Queue on BH radios. |
| STR userName | 1.3.6.1.4.1.161.19.3.3.2.45 | DisplayString | read-write | User name. |
| STR userPassword | 1.3.6.1.4.1.161.19.3.3.2.46 | DisplayString | read-write | User password. |
| INT userAccessLevel | 1.3.6.1.4.1.161.19.3.3.2.47 | INTEGER | read-write | User access level. |
| STR deleteUser | 1.3.6.1.4.1.161.19.3.3.2.48 | DisplayString | read-write | User name to remove. |
| INT twoXRate | 1.3.6.1.4.1.161.19.3.3.2.49 | INTEGER | read-write | To enable or disable double rate. |
| INT lanDhcpState | 1.3.6.1.4.1.161.19.3.3.2.50 | INTEGER | read-write | To enable or disable LAN Interface DHCP feature. |
| INT sessionTimeout | 1.3.6.1.4.1.161.19.3.3.2.51 | INTEGER | read-write | Timer for Telnet, Web and FTP sessions. |
| INT vlanMemberSource | 1.3.6.1.4.1.161.19.3.3.2.52 | INTEGER | read-write | Specified the VLAN member source to display. 0=configured, 1=active configuration. Note that this OID is internal to SNMP and is not available at the Web Interface. |
| STR addCustomFreqList | 1.3.6.1.4.1.161.19.3.3.2.53 | DisplayString | read-write | Add Custom Frequencies. Frequencies can be added in a list separated by commas. Example: 355000, 345000 Frequencies must be in increments of .05 MHz. Examples: 340025, 340050 A get will return the current custom frequency list. Max string length entered cannot exceed 128 character. Note if there is not enough room for all the frequencies none will be added. For use on 3.5/3.6 GHz MIMO OFDM Radios only. |
| STR removeCustomFreqList | 1.3.6.1.4.1.161.19.3.3.2.54 | DisplayString | read-write | Remove Custom Frequencies. Frequencies can be removed in a list separated by commas. Example: 355000, 345000 A get will return the current custom frequencies. For use on 3.5 GHz OFDM Radios only. |
| INT allowColocation | 1.3.6.1.4.1.161.19.3.3.2.55 | INTEGER | read-write | Allow or disallow Colocation for software scheduling Backhaul Timing Masters with hardware scheduling Backhaul Timing Masters. |
| STR changeUsrPwd | 1.3.6.1.4.1.161.19.3.3.2.56 | DisplayString | read-write | Allow to change the password of a given user of a given user. Usage: userName,password. |
| IP mngtIP2 | 1.3.6.1.4.1.161.19.3.3.2.57 | IpAddress | read-write | Management IP address 2. |
| INT subnetMask2 | 1.3.6.1.4.1.161.19.3.3.2.58 | INTEGER | read-write | Subnet mask for the management IP 2. |
| IP mngtIP3 | 1.3.6.1.4.1.161.19.3.3.2.59 | IpAddress | read-write | Management IP address 3. |
| INT subnetMask3 | 1.3.6.1.4.1.161.19.3.3.2.60 | INTEGER | read-write | Subnet mask for the management IP 3. |
| IP mngtIP4 | 1.3.6.1.4.1.161.19.3.3.2.61 | IpAddress | read-write | Management IP address 4. |
| INT subnetMask4 | 1.3.6.1.4.1.161.19.3.3.2.62 | INTEGER | read-write | Subnet mask for the management IP 4. |
| IP mngtIP5 | 1.3.6.1.4.1.161.19.3.3.2.63 | IpAddress | read-write | Management IP address 5. |
| INT subnetMask5 | 1.3.6.1.4.1.161.19.3.3.2.64 | INTEGER | read-write | Subnet mask for the management IP 5. |
| IP mngtIP6 | 1.3.6.1.4.1.161.19.3.3.2.65 | IpAddress | read-write | Management IP address 6. |
| INT subnetMask6 | 1.3.6.1.4.1.161.19.3.3.2.66 | INTEGER | read-write | Subnet mask for the management IP 6. |
| IP mngtIP7 | 1.3.6.1.4.1.161.19.3.3.2.67 | IpAddress | read-write | Management IP address 7. |
| INT subnetMask7 | 1.3.6.1.4.1.161.19.3.3.2.68 | INTEGER | read-write | Subnet mask for the management IP 7. |
| IP mngtIP8 | 1.3.6.1.4.1.161.19.3.3.2.69 | IpAddress | read-write | Management IP address 8. |
| INT subnetMask8 | 1.3.6.1.4.1.161.19.3.3.2.70 | INTEGER | read-write | Subnet mask for the management IP 8. |
| IP mngtIP9 | 1.3.6.1.4.1.161.19.3.3.2.71 | IpAddress | read-write | Management IP address 9. |
| INT subnetMask9 | 1.3.6.1.4.1.161.19.3.3.2.72 | INTEGER | read-write | Subnet mask for the management IP 9. |
| IP mngtIP10 | 1.3.6.1.4.1.161.19.3.3.2.73 | IpAddress | read-write | Management IP address 10. |
| INT subnetMask10 | 1.3.6.1.4.1.161.19.3.3.2.74 | INTEGER | read-write | Subnet mask for the management IP 10. |
| INT bhvlanEnable | 1.3.6.1.4.1.161.19.3.3.2.75 | INTEGER | read-write | To enable or disable VLAN for Backhaul Master/Slave. |
| INT lldpBroadcastEnable | 1.3.6.1.4.1.161.19.3.3.2.76 | INTEGER | read-write | To enable Broadcast of LLDP message, if disabled LLDP uses multicast |
| INT regionCode | 1.3.6.1.4.1.161.19.3.3.2.77 | INTEGER | read-write | Set Region Code for the Unit. Used the individual region[Region] OIDs instead. |
| INT russiaRegion | 1.3.6.1.4.1.161.19.3.3.2.78 | INTEGER | read-write | Set Category Region for Russian 5.9/6.05 GHz Radio Only. Use setting under regionAsia now. |
| STR commStringROnly | 1.3.6.1.4.1.161.19.3.3.2.79 | DisplayString | read-write | Set Read Only commnunity string. |
| INT ethernetLinkSpeed | 1.3.6.1.4.1.161.19.3.3.2.80 | INTEGER | read-write | Set/Get Ethernet link speed and duplex settings. Note that the Gigabit options are only valid for boards that support Gigabit speeds. |
| INT cyclicPrefix | 1.3.6.1.4.1.161.19.3.3.2.81 | INTEGER | read-write | Cyclic Prefix value, for OFDM Radios only. Deprecated for MIMO SMs. For PMP430 SMs, this value is only used while in PMP430 mode (1/16 is forced in PMP450 mode). |
| INT numberCustomFreq | 1.3.6.1.4.1.161.19.3.3.2.82 | INTEGER | read-only | Number of custom frequencies added. There is a maximum of 100. For use on 3.5 GHz OFDM Radios only. |
| STR channelBandwidth | 1.3.6.1.4.1.161.19.3.3.2.83 | DisplayString | read-only | The current channel bandwidth in MHz. For use on OFDM Radios only. Obsoleted for MIMO SMs. |
| INT setDefaults | 1.3.6.1.4.1.161.19.3.3.2.84 | INTEGER | read-write | Setting this to 1 will set the radio to Factory Defaults after the next reboot. Setting this to 0 will undo Factory Defaults if and only if Factory Defaults have been set previously without rebooting. Reading this OID will return 0 if Factory Defaults are not set, or a 2 if Factory Defaults are set and we are now awaiting a reboot. NOTE: this operation is reversible as long as you write a 0 to this OID prior to reboot. As a security measure, this OID is only valid when the radio was booted with the default plug inserted. If the default plug was not inserted on boot, then attempting to set this OID will fail. |
| INT radioRateAdapt | 1.3.6.1.4.1.161.19.3.3.2.85 | INTEGER | read-write | Rate adaptation parameter. 0: no rate adaptation. 1: 1x and 2x adaptation. 2: 1x, 2x and 3x adaptation (OFDM only). 3: 1x, 2x, 3x and 4x adaption (OFDM only). 4: 1x (MIMO duplicate on both paths). 5: 1x/2x (MIMO). 7: 1x/2x/4x (MIMO). 8: 1x/2x/4x/6x (MIMO). 9: 1x/2x/4x/6x/8x (MIMO). For PMP430 radios this applies to Downlink Rate Adapt only. Use radioRateAdaptUL for setting uplink rate adapt on PMP430 radios. |
| INT siteInfoViewable | 1.3.6.1.4.1.161.19.3.3.2.86 | INTEGER | read-write | Enable non login users the ability to view Site Information |
| INT largeVCQ | 1.3.6.1.4.1.161.19.3.3.2.87 | INTEGER | read-write | Enable or disable Large VC Qs for SM or PTP radios. Enable when Uplink is being used for camera video feed. |
| STR latitude | 1.3.6.1.4.1.161.19.3.3.2.88 | DisplayString | read-write | The latitude setting of this unit in decimal degrees. |
| STR longitude | 1.3.6.1.4.1.161.19.3.3.2.89 | DisplayString | read-write | The longitude setting of this unit in decimal degrees. |
| INT height | 1.3.6.1.4.1.161.19.3.3.2.90 | INTEGER | read-write | The height setting of this unit in meters. |
| INT bandwidth | 1.3.6.1.4.1.161.19.3.3.2.91 | INTEGER | read-write | Radio bandwidth setting. Deprecated for MIMO SMs. Instead use bandwidthScan. |
| INT dataScramblingMethod | 1.3.6.1.4.1.161.19.3.3.2.92 | INTEGER | read-only | This OID is for OFDM only and is obsolete. |
| INT portVID | 1.3.6.1.4.1.161.19.3.3.2.93 | INTEGER | read-write | Backhaul Port VID (PVID). |
| INT radioRateAdaptUL | 1.3.6.1.4.1.161.19.3.3.2.94 | INTEGER | read-write | Uplink Rate adaptation parameter (OFDM PMP430 only). 0: no rate adaptation. 1: 1x and 2x adaptation. 2: 1x, 2x and 3x adaptation. 3: 1x, 2x, 3x and 4x adaption. For PMP430 radios this applies to Uplink Rate Adapt only. Use radioRateAdapt for setting downlink rate adapt. 4x rate adapt not permitted on AES, 20MHz, 1/16 CP radios. |
| INT providerVID | 1.3.6.1.4.1.161.19.3.3.2.95 | INTEGER | read-write | Provider VID for QinQ VLAN. |
| MAC mac1VIDMapAddr | 1.3.6.1.4.1.161.19.3.3.2.96 | MacAddress | read-write | MAC Address for Entry 1 in MAC Address VID Mapping Table. |
| INT mac1VIDMapVid | 1.3.6.1.4.1.161.19.3.3.2.97 | INTEGER | read-write | VID for Entry 1 in MAC Address VID Mapping Table. |
| MAC mac2VIDMapAddr | 1.3.6.1.4.1.161.19.3.3.2.98 | MacAddress | read-write | MAC Address for Entry 2 in MAC Address VID Mapping Table. |
| INT mac2VIDMapVid | 1.3.6.1.4.1.161.19.3.3.2.99 | INTEGER | read-write | VID for Entry 2 in MAC Address VID Mapping Table. |
| MAC mac3VIDMapAddr | 1.3.6.1.4.1.161.19.3.3.2.100 | MacAddress | read-write | MAC Address for Entry 3 in MAC Address VID Mapping Table. |
| INT mac3VIDMapVid | 1.3.6.1.4.1.161.19.3.3.2.101 | INTEGER | read-write | VID for Entry 3 in MAC Address VID Mapping Table. |
| MAC mac4VIDMapAddr | 1.3.6.1.4.1.161.19.3.3.2.102 | MacAddress | read-write | MAC Address for Entry 4 in MAC Address VID Mapping Table. |
| INT mac4VIDMapVid | 1.3.6.1.4.1.161.19.3.3.2.103 | INTEGER | read-write | VID for Entry 4 in MAC Address VID Mapping Table. |
| MAC mac5VIDMapAddr | 1.3.6.1.4.1.161.19.3.3.2.104 | MacAddress | read-write | MAC Address for Entry 5 in MAC Address VID Mapping Table. |
| INT mac5VIDMapVid | 1.3.6.1.4.1.161.19.3.3.2.105 | INTEGER | read-write | VID for Entry 5 in MAC Address VID Mapping Table. |
| MAC mac6VIDMapAddr | 1.3.6.1.4.1.161.19.3.3.2.106 | MacAddress | read-write | MAC Address for Entry 6 in MAC Address VID Mapping Table. |
| INT mac6VIDMapVid | 1.3.6.1.4.1.161.19.3.3.2.107 | INTEGER | read-write | VID for Entry 6 in MAC Address VID Mapping Table. |
| MAC mac7VIDMapAddr | 1.3.6.1.4.1.161.19.3.3.2.108 | MacAddress | read-write | MAC Address for Entry 7 in MAC Address VID Mapping Table. |
| INT mac7VIDMapVid | 1.3.6.1.4.1.161.19.3.3.2.109 | INTEGER | read-write | VID for Entry 7 in MAC Address VID Mapping Table. |
| MAC mac8VIDMapAddr | 1.3.6.1.4.1.161.19.3.3.2.110 | MacAddress | read-write | MAC Address for Entry 8 in MAC Address VID Mapping Table. |
| INT mac8VIDMapVid | 1.3.6.1.4.1.161.19.3.3.2.111 | INTEGER | read-write | VID for Entry 8 in MAC Address VID Mapping Table. |
| MAC mac9VIDMapAddr | 1.3.6.1.4.1.161.19.3.3.2.112 | MacAddress | read-write | MAC Address for Entry 9 in MAC Address VID Mapping Table. |
| INT mac9VIDMapVid | 1.3.6.1.4.1.161.19.3.3.2.113 | INTEGER | read-write | VID for Entry 9 in MAC Address VID Mapping Table. |
| MAC mac10VIDMapAddr | 1.3.6.1.4.1.161.19.3.3.2.114 | MacAddress | read-write | MAC Address for Entry 10 in MAC Address VID Mapping Table. |
| INT mac10VIDMapVid | 1.3.6.1.4.1.161.19.3.3.2.115 | INTEGER | read-write | VID for Entry 10 in MAC Address VID Mapping Table. |
| INT vlanPortType | 1.3.6.1.4.1.161.19.3.3.2.116 | INTEGER | read-write | VLAN Port Type for VLAN interface. Default is Q. |
| INT vlanAcceptQinQFrames | 1.3.6.1.4.1.161.19.3.3.2.117 | INTEGER | read-write | Allow/Disallow packets already doubly-tagged (QinQ) to ingress the FEC of BHM, BHS, or MP SM. Not configurable on MP AP. |
| INT whispWebUserAccessMode | 1.3.6.1.4.1.161.19.3.3.2.118 | INTEGER | read-write | This variable selects if web page users for the radio should be authenticated locally or via a centralised remote Radius server |
| INT usrAccountEnableAccounting | 1.3.6.1.4.1.161.19.3.3.2.119 | INTEGER | read-write | Select the level of accounting information to be reported to the server |
| INT allowRejectThenLocal | 1.3.6.1.4.1.161.19.3.3.2.120 | INTEGER | read-write | Control for allowing local authenication if the AAA remote server |
| INT snrCalculation | 1.3.6.1.4.1.161.19.3.3.2.121 | INTEGER | read-write | This OID is deprecated. Receive quality calulation is always on since it no longer affects packet per second performance. |
| INT priorityPrecedence | 1.3.6.1.4.1.161.19.3.3.2.122 | INTEGER | read-write | Allows user to decide if 802.1p or DiffServ priority bits should be used first when making priority decisions. |
| INT installationColorCode | 1.3.6.1.4.1.161.19.3.3.2.123 | INTEGER | read-write | Installation Color Code. Allows non-configured SMs to register to an AP with UCC enabled in order to facilitate remote provisioning. |
| INT apSmMode | 1.3.6.1.4.1.161.19.3.3.2.124 | INTEGER | read-write | Set AP to SM or SM to AP. Useful for facillitating scripting of running Spectrum Analyzer on an AP. Radio must have AP Feature Key. 1 - Set to SM, 0 - Set to AP. |
| INT pppoeFilter | 1.3.6.1.4.1.161.19.3.3.2.125 | INTEGER | read-write | To set PPPoE packet filter. |
| INT smbFilter | 1.3.6.1.4.1.161.19.3.3.2.126 | INTEGER | read-write | To set SMB packet filter. |
| INT snmpFilter | 1.3.6.1.4.1.161.19.3.3.2.127 | INTEGER | read-write | To set SNMP packet filter. |
| INT userP1Filter | 1.3.6.1.4.1.161.19.3.3.2.128 | INTEGER | read-write | To set user defined port 1 packet filter. |
| INT userP2Filter | 1.3.6.1.4.1.161.19.3.3.2.129 | INTEGER | read-write | To set user defined port 2 packet filter. |
| INT userP3Filter | 1.3.6.1.4.1.161.19.3.3.2.130 | INTEGER | read-write | To set user defined port 3 packet filter. |
| INT allOtherIpFilter | 1.3.6.1.4.1.161.19.3.3.2.131 | INTEGER | read-write | To set all other IPv4 packet filter. |
| INT allIpv4Filter | 1.3.6.1.4.1.161.19.3.3.2.132 | INTEGER | read-write | To set all IPv4 packet filter. Enabling this will automatically enable all of the known IP filters (SMB, SNMP, Bootp, IPv4 Mcast, User Defined Ports, and All Other IPv4). |
| INT arpFilter | 1.3.6.1.4.1.161.19.3.3.2.133 | INTEGER | read-write | To set ARP packet filter. |
| INT allOthersFilter | 1.3.6.1.4.1.161.19.3.3.2.134 | INTEGER | read-write | To set all other packet filter when. |
| INT userDefinedPort1 | 1.3.6.1.4.1.161.19.3.3.2.135 | INTEGER | read-write | An integer value of number one user defined port. Range:0-65535 |
| INT port1TCPFilter | 1.3.6.1.4.1.161.19.3.3.2.136 | INTEGER | read-write | To set user defined port 1 TCP traffic filter. |
| INT port1UDPFilter | 1.3.6.1.4.1.161.19.3.3.2.137 | INTEGER | read-write | To set user defined port 1 UDP traffic filter. |
| INT userDefinedPort2 | 1.3.6.1.4.1.161.19.3.3.2.138 | INTEGER | read-write | An integer value of number two user defined port. Range:0-65535 |
| INT port2TCPFilter | 1.3.6.1.4.1.161.19.3.3.2.139 | INTEGER | read-write | To set user defined port 2 TCP traffic filter. |
| INT port2UDPFilter | 1.3.6.1.4.1.161.19.3.3.2.140 | INTEGER | read-write | To set user defined port 2 UDP traffic filter. |
| INT userDefinedPort3 | 1.3.6.1.4.1.161.19.3.3.2.141 | INTEGER | read-write | An integer value of number three user defined port. Range:0-65535 |
| INT port3TCPFilter | 1.3.6.1.4.1.161.19.3.3.2.142 | INTEGER | read-write | To set user defined port 3 TCP traffic filter. |
| INT port3UDPFilter | 1.3.6.1.4.1.161.19.3.3.2.143 | INTEGER | read-write | To set user defined port 3 UDP traffic filter. |
| INT bootpcFilter | 1.3.6.1.4.1.161.19.3.3.2.144 | INTEGER | read-write | To set bootp client sourced packets filter. |
| INT bootpsFilter | 1.3.6.1.4.1.161.19.3.3.2.145 | INTEGER | read-write | To set bootp server sourced packets filter. |
| INT ip4MultFilter | 1.3.6.1.4.1.161.19.3.3.2.146 | INTEGER | read-write | To set IPv4 MultiCast packets filter when NAT is disabled. |
| INT packetFilterDirection | 1.3.6.1.4.1.161.19.3.3.2.147 | INTEGER | read-write | To set packet filter direction. Upstream is default. |
| INT encryptionConfig | 1.3.6.1.4.1.161.19.3.3.2.148 | INTEGER | read-write | For supported radio, set the encryption algorithm to use. DES by default. Cannot be set if encryption is disabled. |
| INT pppoeCtlPriority | 1.3.6.1.4.1.161.19.3.3.2.149 | INTEGER | read-write | Prioritization of PPPoE Control packets. |
| INT ftpPort | 1.3.6.1.4.1.161.19.3.3.2.150 | INTEGER | read-write | Port used to for FTP. Default is 21. |
| INT httpPort | 1.3.6.1.4.1.161.19.3.3.2.151 | INTEGER | read-write | Port used to for HTTP. Default is 80. |
| INT snmpPort | 1.3.6.1.4.1.161.19.3.3.2.153 | INTEGER | read-write | Port used to for SNMP. Default is 161. |
| INT snmpTrapPort | 1.3.6.1.4.1.161.19.3.3.2.154 | INTEGER | read-write | Port used to for SNMP Traps. Default is 162. |
| INT syslogDomainNameAppend | 1.3.6.1.4.1.161.19.3.3.2.156 | INTEGER | read-write | Select whether to append the configured management domain name to the Syslog server name. For example, if dnsMgmtDomainName is set to 'example.com', syslogServerAddr is set to 'syslog1', and syslogDomainNameAppend is set to appendDomain, the Syslog Server name used would be 'syslog1.example.com'. |
| STR syslogServerAddr | 1.3.6.1.4.1.161.19.3.3.2.157 | DisplayString | read-write | Syslog server address either in dotted decimal notation or a Fully Qualified Domain Name |
| INT syslogServerPort | 1.3.6.1.4.1.161.19.3.3.2.158 | INTEGER | read-write | Listening port on the Syslog server. Default is 514. |
| INT syslogMinLevel | 1.3.6.1.4.1.161.19.3.3.2.159 | INTEGER | read-write | Sets the minimum syslog severity to transmit. Messages with a lower severity value (i.e. numerically higher) than this will not be transmitted. |
| INT lan1DhcpRelease | 1.3.6.1.4.1.161.19.3.3.2.201 | INTEGER | read-write | Setting the variable to '1' will release LAN1's IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is disabled. |
| INT lan1DhcpRenew | 1.3.6.1.4.1.161.19.3.3.2.202 | INTEGER | read-write | Setting the variable to '1' will renew LAN1's lease time for its current IP address. Applicable only when NAT is disabled. |
| INT lan3DhcpRelease | 1.3.6.1.4.1.161.19.3.3.2.203 | INTEGER | read-write | Setting the variable to '1' will release LAN3's (RF Public) IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is enabled. |
| INT lan3DhcpRenew | 1.3.6.1.4.1.161.19.3.3.2.204 | INTEGER | read-write | Setting the variable to '1' will renew LAN3's (RF Public) lease time for its current IP address. Applicable only when NAT is enabled. |
| INT natDhcpRelease | 1.3.6.1.4.1.161.19.3.3.2.205 | INTEGER | read-write | Setting the variable to '1' will release WAN's (NAT Public) IP address and send a DHCP Release Message to the DHCP server. Applicable only when NAT is enabled. |
| INT natDhcpRenew | 1.3.6.1.4.1.161.19.3.3.2.206 | INTEGER | read-write | Setting the variable to '1' will renew WAN's (NAT Public) lease time for its current IP address. Applicable only when NAT is enabled. |
| INT region | 1.3.6.1.4.1.161.19.3.3.2.207 | INTEGER | read-only | Set Region Code for the Unit. |
| INT regionAsia | 1.3.6.1.4.1.161.19.3.3.2.208 | INTEGER | read-write | Country Code for Asia. |
| INT regionEurope | 1.3.6.1.4.1.161.19.3.3.2.209 | INTEGER | read-write | Country Code for Europe. |
| INT regionNorthAmerica | 1.3.6.1.4.1.161.19.3.3.2.210 | INTEGER | read-write | Country Code for North America. |
| INT regionOceania | 1.3.6.1.4.1.161.19.3.3.2.211 | INTEGER | read-write | Country Code for Oceania. |
| INT regionSouthAmerica | 1.3.6.1.4.1.161.19.3.3.2.212 | INTEGER | read-write | Country Code for South America. |
| INT regionOtherRegulatory | 1.3.6.1.4.1.161.19.3.3.2.213 | INTEGER | read-write | Regulatory setting for governing regulatory body. |
| INT interleave | 1.3.6.1.4.1.161.19.3.3.2.214 | INTEGER | read-write | Engineering use only. |
| INT receiveQualityDebug | 1.3.6.1.4.1.161.19.3.3.2.215 | INTEGER | read-write | Enable or disable receive quality calculations for every packet. Enabling(1) will calulate receive quality on all receiving packets. Due to load on CPU, will slightly packet per second capabilities on AP/BH. Default to disabled for all radios. Only applicable to GenII OFDM products and up. |
| INT apType | 1.3.6.1.4.1.161.19.3.3.2.216 | INTEGER | read-write | AP Mode of Operation. In standardAP mode, all possible sync sources will be made availble and used for autoSync operation. In remoteAP mode, sync over power port will not be available as a sync source. Remote AP mode is where the AP's timing port is connected to an SM's timing port via a sync cable. In this mode, GPS data is unavailable and sync over power port shouldn't be used. If sync over power is desired, and a CMM or other sync over power device is in use, then select standardAP mode. |
| INT regionAfrica | 1.3.6.1.4.1.161.19.3.3.2.217 | INTEGER | read-write | Country Code for Africa. |
| STR addCustomFreqMimo | 1.3.6.1.4.1.161.19.3.3.2.218 | DisplayString | read-write | Adds a particular frequency, applicable for both the AP and SM. |
| STR removeCustomFreqMimo | 1.3.6.1.4.1.161.19.3.3.2.219 | DisplayString | read-write | Removes a particular frequency, applicable for both the AP and SM. |
| INT timedSpectrumAnalysisDurationBox | 1.3.6.1.4.1.161.19.3.3.2.220 | INTEGER | read-write | Value in seconds for a timed spectrum analysis. Range is 10-1000 seconds. |
| INT spectrumAnalysisActionBox | 1.3.6.1.4.1.161.19.3.3.2.221 | INTEGER | read-write | Start or stop timed or continuous Spectrum Analysis and also give status. (0) - Stop Spectrum Analysis (1) - Start Timed Spectrum Analysis (2) - Start Continuous Spectrum Analysis (3) - Idle, no Spectrum Analysis results. (4) - Idle, Spectrum Analysis results available. (5) - Timed or Remote Spectrum Analysis in progress. (6) - Continuous Spectrum Analysis in progress. Note: Continuous mode has a max of 24 hours. (7) - Spectrum Analyzer not ready. |
| whispBoxControls | 1.3.6.1.4.1.161.19.3.3.3 | |||
| INT saveFlash | 1.3.6.1.4.1.161.19.3.3.3.1 | INTEGER | read-write | This variable is currently deprecated. |
| INT reboot | 1.3.6.1.4.1.161.19.3.3.3.2 | INTEGER | read-write | Setting the variable to 1 will reboot the unit. When the unit finishes rebooting, it will be in finishedReboot state. |
| INT clearEventLog | 1.3.6.1.4.1.161.19.3.3.3.3 | INTEGER | read-write | Setting the variable to 1 will clear the event log. |
| INT rebootIfRequired | 1.3.6.1.4.1.161.19.3.3.3.4 | INTEGER | read-write | Setting the variable to 1 will reboot the unit if reboot is required. |
| INT clearBERStats | 1.3.6.1.4.1.161.19.3.3.3.5 | INTEGER | read-write | Set to clear the BER statistics by sending a 'clearBERStats'. Value is set back to 'doNotClearBERStats' When action is complete. |
| INT updateDevice | 1.3.6.1.4.1.161.19.3.3.3.6 | INTEGER | read-write | Use to update the software on the device |
| whispBoxBridgeTable | 1.3.6.1.4.1.161.19.3.3.4 | not-accessible | Bridge table. | |
| whispBoxBridgeEntry | 1.3.6.1.4.1.161.19.3.3.4.1 | not-accessible | Bridge entry. | |
| MAC whispBridgeMacAddr | 1.3.6.1.4.1.161.19.3.3.4.1.1 | MacAddress | read-only | MAC Address of the registered enity. |
| WHI whispBridgeDesLuid | 1.3.6.1.4.1.161.19.3.3.4.1.2 | WhispLUID | read-only | This is the Local Unit Identifier assigned to Subscriber Modems. |
| INT whispBridgeAge | 1.3.6.1.4.1.161.19.3.3.4.1.3 | INTEGER | read-only | Table entry last access age in minutes. |
| INT whispBridgeExt | 1.3.6.1.4.1.161.19.3.3.4.1.4 | INTEGER | read-only | Timeout extension flag for entries which also reside in the PNA APR cache. |
| INT whispBridgeHash | 1.3.6.1.4.1.161.19.3.3.4.1.5 | INTEGER | read-only | Hash table array index. |
| INT whispBridgeCAM | 1.3.6.1.4.1.161.19.3.3.4.1.6 | INTEGER | read-only | This entry is deprecated. |
| whispBoxEventLog | 1.3.6.1.4.1.161.19.3.3.5 | |||
| STR whispBoxEvntLog | 1.3.6.1.4.1.161.19.3.3.5.1 | EventString | read-only | Event log for AP and SM. |
| whispBoxConf | 1.3.6.1.4.1.161.19.3.3.6 | |||
| whispBoxGroups | 1.3.6.1.4.1.161.19.3.3.6.1 | |||
| whispBoxAttributesGroup | 1.3.6.1.4.1.161.19.3.3.6.1.1 | Canopy Box Level Attributes group. | ||
| whispBoxControlGroup | 1.3.6.1.4.1.161.19.3.3.6.1.2 | Canopy Box Level control group. | ||
| whispBoxBTGroup | 1.3.6.1.4.1.161.19.3.3.6.1.3 | Canopy Box Bridging Table group. | ||
| whispBoxVLANTableGroup | 1.3.6.1.4.1.161.19.3.3.6.1.4 | Canopy Box VLAN member Table group. | ||
| whispBoxCPTableGroup | 1.3.6.1.4.1.161.19.3.3.6.1.5 | Code Point Table group. | ||
| whispBoxUserTableGroup | 1.3.6.1.4.1.161.19.3.3.6.1.6 | Canopy Box User Information Table group. | ||
| whispLayer2NeighborTableGroup | 1.3.6.1.4.1.161.19.3.3.6.1.7 | Canopy Box Layer 2 Neighbor information. | ||
| whispBoxNotifGroup | 1.3.6.1.4.1.161.19.3.3.6.1.8 | Canopy Box Notification Group. | ||
| whispBoxBridgeVar | 1.3.6.1.4.1.161.19.3.3.7 | |||
| INT whispBridgeTbUsed | 1.3.6.1.4.1.161.19.3.3.7.1 | INTEGER | read-only | Number of used entries in bridging table. |
| INT whispBridgeTbFree | 1.3.6.1.4.1.161.19.3.3.7.2 | INTEGER | read-only | Number of free entries in bridging table. |
| INT whispBridgeTbErr | 1.3.6.1.4.1.161.19.3.3.7.3 | INTEGER | read-only | Bridging table errors. |
| whispVLANTable | 1.3.6.1.4.1.161.19.3.3.8 | not-accessible | VLAN member table. | |
| whispVLANEntry | 1.3.6.1.4.1.161.19.3.3.8.1 | not-accessible | VLAN entry. | |
| INT whispVID | 1.3.6.1.4.1.161.19.3.3.8.1.1 | INTEGER | read-only | VLAN member ID. |
| STR whispVType | 1.3.6.1.4.1.161.19.3.3.8.1.2 | DisplayString | read-only | VLAN member type. |
| INT whispVAge | 1.3.6.1.4.1.161.19.3.3.8.1.3 | INTEGER | read-only | VLAN member age. |
| whispBoxCPVar | 1.3.6.1.4.1.161.19.3.3.9 | |||
| INT codePoint0 | 1.3.6.1.4.1.161.19.3.3.9.1 | INTEGER | read-only | Code Point 0. |
| INT codePoint1 | 1.3.6.1.4.1.161.19.3.3.9.2 | INTEGER | read-write | Code Point 1. |
| INT codePoint2 | 1.3.6.1.4.1.161.19.3.3.9.3 | INTEGER | read-write | Code Point 2. |
| INT codePoint3 | 1.3.6.1.4.1.161.19.3.3.9.4 | INTEGER | read-write | Code Point 3. |
| INT codePoint4 | 1.3.6.1.4.1.161.19.3.3.9.5 | INTEGER | read-write | Code Point 4. |
| INT codePoint5 | 1.3.6.1.4.1.161.19.3.3.9.6 | INTEGER | read-write | Code Point 5. |
| INT codePoint6 | 1.3.6.1.4.1.161.19.3.3.9.7 | INTEGER | read-write | Code Point 6. |
| INT codePoint7 | 1.3.6.1.4.1.161.19.3.3.9.8 | INTEGER | read-write | Code Point 7. |
| INT codePoint8 | 1.3.6.1.4.1.161.19.3.3.9.9 | INTEGER | read-write | Code Point 8. |
| INT codePoint9 | 1.3.6.1.4.1.161.19.3.3.9.10 | INTEGER | read-write | Code Point 9. |
| INT codePoint10 | 1.3.6.1.4.1.161.19.3.3.9.11 | INTEGER | read-write | Code Point 10. |
| INT codePoint11 | 1.3.6.1.4.1.161.19.3.3.9.12 | INTEGER | read-write | Code Point 11. |
| INT codePoint12 | 1.3.6.1.4.1.161.19.3.3.9.13 | INTEGER | read-write | Code Point 12. |
| INT codePoint13 | 1.3.6.1.4.1.161.19.3.3.9.14 | INTEGER | read-write | Code Point 13. |
| INT codePoint14 | 1.3.6.1.4.1.161.19.3.3.9.15 | INTEGER | read-write | Code Point 14. |
| INT codePoint15 | 1.3.6.1.4.1.161.19.3.3.9.16 | INTEGER | read-write | Code Point 15. |
| INT codePoint16 | 1.3.6.1.4.1.161.19.3.3.9.17 | INTEGER | read-write | Code Point 16. |
| INT codePoint17 | 1.3.6.1.4.1.161.19.3.3.9.18 | INTEGER | read-write | Code Point 17. |
| INT codePoint18 | 1.3.6.1.4.1.161.19.3.3.9.19 | INTEGER | read-write | Code Point 18. |
| INT codePoint19 | 1.3.6.1.4.1.161.19.3.3.9.20 | INTEGER | read-write | Code Point 19. |
| INT codePoint20 | 1.3.6.1.4.1.161.19.3.3.9.21 | INTEGER | read-write | Code Point 20. |
| INT codePoint21 | 1.3.6.1.4.1.161.19.3.3.9.22 | INTEGER | read-write | Code Point 21. |
| INT codePoint22 | 1.3.6.1.4.1.161.19.3.3.9.23 | INTEGER | read-write | Code Point 22. |
| INT codePoint23 | 1.3.6.1.4.1.161.19.3.3.9.24 | INTEGER | read-write | Code Point 23. |
| INT codePoint24 | 1.3.6.1.4.1.161.19.3.3.9.25 | INTEGER | read-write | Code Point 24. |
| INT codePoint25 | 1.3.6.1.4.1.161.19.3.3.9.26 | INTEGER | read-write | Code Point 25. |
| INT codePoint26 | 1.3.6.1.4.1.161.19.3.3.9.27 | INTEGER | read-write | Code Point 26. |
| INT codePoint27 | 1.3.6.1.4.1.161.19.3.3.9.28 | INTEGER | read-write | Code Point 27. |
| INT codePoint28 | 1.3.6.1.4.1.161.19.3.3.9.29 | INTEGER | read-write | Code Point 28. |
| INT codePoint29 | 1.3.6.1.4.1.161.19.3.3.9.30 | INTEGER | read-write | Code Point 29. |
| INT codePoint30 | 1.3.6.1.4.1.161.19.3.3.9.31 | INTEGER | read-write | Code Point 30. |
| INT codePoint31 | 1.3.6.1.4.1.161.19.3.3.9.32 | INTEGER | read-write | Code Point 31. |
| INT codePoint32 | 1.3.6.1.4.1.161.19.3.3.9.33 | INTEGER | read-write | Code Point 32. |
| INT codePoint33 | 1.3.6.1.4.1.161.19.3.3.9.34 | INTEGER | read-write | Code Point 33. |
| INT codePoint34 | 1.3.6.1.4.1.161.19.3.3.9.35 | INTEGER | read-write | Code Point 34. |
| INT codePoint35 | 1.3.6.1.4.1.161.19.3.3.9.36 | INTEGER | read-write | Code Point 35. |
| INT codePoint36 | 1.3.6.1.4.1.161.19.3.3.9.37 | INTEGER | read-write | Code Point 36. |
| INT codePoint37 | 1.3.6.1.4.1.161.19.3.3.9.38 | INTEGER | read-write | Code Point 37. |
| INT codePoint38 | 1.3.6.1.4.1.161.19.3.3.9.39 | INTEGER | read-write | Code Point 38. |
| INT codePoint39 | 1.3.6.1.4.1.161.19.3.3.9.40 | INTEGER | read-write | Code Point 39. |
| INT codePoint40 | 1.3.6.1.4.1.161.19.3.3.9.41 | INTEGER | read-write | Code Point 40. |
| INT codePoint41 | 1.3.6.1.4.1.161.19.3.3.9.42 | INTEGER | read-write | Code Point 41. |
| INT codePoint42 | 1.3.6.1.4.1.161.19.3.3.9.43 | INTEGER | read-write | Code Point 42. |
| INT codePoint43 | 1.3.6.1.4.1.161.19.3.3.9.44 | INTEGER | read-write | Code Point 43. |
| INT codePoint44 | 1.3.6.1.4.1.161.19.3.3.9.45 | INTEGER | read-write | Code Point 44. |
| INT codePoint45 | 1.3.6.1.4.1.161.19.3.3.9.46 | INTEGER | read-write | Code Point 45. |
| INT codePoint46 | 1.3.6.1.4.1.161.19.3.3.9.47 | INTEGER | read-write | Code Point 46. |
| INT codePoint47 | 1.3.6.1.4.1.161.19.3.3.9.48 | INTEGER | read-write | Code Point 47. |
| INT codePoint48 | 1.3.6.1.4.1.161.19.3.3.9.49 | INTEGER | read-only | Code Point 48. |
| INT codePoint49 | 1.3.6.1.4.1.161.19.3.3.9.50 | INTEGER | read-write | Code Point 49. |
| INT codePoint50 | 1.3.6.1.4.1.161.19.3.3.9.51 | INTEGER | read-write | Code Point 50. |
| INT codePoint51 | 1.3.6.1.4.1.161.19.3.3.9.52 | INTEGER | read-write | Code Point 51. |
| INT codePoint52 | 1.3.6.1.4.1.161.19.3.3.9.53 | INTEGER | read-write | Code Point 52. |
| INT codePoint53 | 1.3.6.1.4.1.161.19.3.3.9.54 | INTEGER | read-write | Code Point 53. |
| INT codePoint54 | 1.3.6.1.4.1.161.19.3.3.9.55 | INTEGER | read-write | Code Point 54. |
| INT codePoint55 | 1.3.6.1.4.1.161.19.3.3.9.56 | INTEGER | read-write | Code Point 55. |
| INT codePoint56 | 1.3.6.1.4.1.161.19.3.3.9.57 | INTEGER | read-only | Code Point 56. |
| INT codePoint57 | 1.3.6.1.4.1.161.19.3.3.9.58 | INTEGER | read-write | Code Point 57. |
| INT codePoint58 | 1.3.6.1.4.1.161.19.3.3.9.59 | INTEGER | read-write | Code Point 58. |
| INT codePoint59 | 1.3.6.1.4.1.161.19.3.3.9.60 | INTEGER | read-write | Code Point 59. |
| INT codePoint60 | 1.3.6.1.4.1.161.19.3.3.9.61 | INTEGER | read-write | Code Point 60. |
| INT codePoint61 | 1.3.6.1.4.1.161.19.3.3.9.62 | INTEGER | read-write | Code Point 61. |
| INT codePoint62 | 1.3.6.1.4.1.161.19.3.3.9.63 | INTEGER | read-write | Code Point 62. |
| INT codePoint63 | 1.3.6.1.4.1.161.19.3.3.9.64 | INTEGER | read-write | Code Point 63. |
| whispUserTable | 1.3.6.1.4.1.161.19.3.3.10 | not-accessible | User information table. | |
| whispUserEntry | 1.3.6.1.4.1.161.19.3.3.10.1 | not-accessible | User entry. | |
| INT entryIndex | 1.3.6.1.4.1.161.19.3.3.10.1.1 | INTEGER | read-only | User information table index. |
| STR userLoginName | 1.3.6.1.4.1.161.19.3.3.10.1.2 | DisplayString | read-only | User name. |
| STR userPswd | 1.3.6.1.4.1.161.19.3.3.10.1.3 | DisplayString | read-only | User password. |
| INT accessLevel | 1.3.6.1.4.1.161.19.3.3.10.1.4 | INTEGER | read-only | User access level. |
| INT loginStatus | 1.3.6.1.4.1.161.19.3.3.10.1.5 | INTEGER | read-only | User current status. |
| INT loginMethod | 1.3.6.1.4.1.161.19.3.3.10.1.6 | INTEGER | read-only | User login method. |
| INT sessionTime | 1.3.6.1.4.1.161.19.3.3.10.1.7 | INTEGER | read-only | Users logged in session time. |
| whispLayer2NeighborTable | 1.3.6.1.4.1.161.19.3.3.11 | not-accessible | Neighbor information table. | |
| whispLayer2NeighborEntry | 1.3.6.1.4.1.161.19.3.3.11.1 | not-accessible | Neighbor Entry. | |
| INT entryL2Index | 1.3.6.1.4.1.161.19.3.3.11.1.1 | INTEGER | read-only | Neighbor information table index. |
| STR neighborMAC | 1.3.6.1.4.1.161.19.3.3.11.1.2 | DisplayString | read-only | Neighbor MAC. |
| STR neighborIP | 1.3.6.1.4.1.161.19.3.3.11.1.3 | DisplayString | read-only | Neighbor IP. |
| STR neighborSiteName | 1.3.6.1.4.1.161.19.3.3.11.1.4 | DisplayString | read-only | Neighbor Site Name. |
| whispBoxEvent | 1.3.6.1.4.1.161.19.3.3.12 | |||
| whispBoxDHCPClientEvent | 1.3.6.1.4.1.161.19.3.3.12.1 | |||
| NTF boxLan1DHCPClientEvent | 1.3.6.1.4.1.161.19.3.3.12.1.1 | Lan1 DHCP Client has received a new address via DHCP | ||
| whispBoxDNS | 1.3.6.1.4.1.161.19.3.3.13 | |||
| INT dnsIpState | 1.3.6.1.4.1.161.19.3.3.13.1 | INTEGER | read-write | Configuration for DNS server IP addresses of the management interface are learned: 0 : Manual, must configure dnsPrimaryMgmtIP and dnsAlternateMgmtIP 1 : Automatic, DNS servers IP addresses are learned from DHCP response of the interface |
| IP dnsPrimaryMgmtIP | 1.3.6.1.4.1.161.19.3.3.13.2 | IpAddress | read-write | Primary DNS IP address for the management interface. |
| IP dnsAlternateMgmtIP | 1.3.6.1.4.1.161.19.3.3.13.3 | IpAddress | read-write | Secondary DNS IP address for the management interface. |
| STR dnsMgmtDomainName | 1.3.6.1.4.1.161.19.3.3.13.4 | DisplayString | read-write | Domain Name to use for management DNS configuration. This domain name may be concatonated to DNS names used configured for the management interface. |
| INT trapDomainNameAppend | 1.3.6.1.4.1.161.19.3.3.13.5 | INTEGER | read-write | Select whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', trap1 is set to 'trap1', and trapDomainNameAppend is set to appendDomain, the trap1 name used would be 'trap1.example.com'. |
| STR trap1 | 1.3.6.1.4.1.161.19.3.3.13.6 | DisplayString | read-write | SNMP Trap IP Address 1. Format is either an IP address or DNS name. |
| STR trap2 | 1.3.6.1.4.1.161.19.3.3.13.7 | DisplayString | read-write | SNMP Trap IP Address 2. Format is either an IP address or DNS name. |
| STR trap3 | 1.3.6.1.4.1.161.19.3.3.13.8 | DisplayString | read-write | SNMP Trap IP Address 3. Format is either an IP address or DNS name. |
| STR trap4 | 1.3.6.1.4.1.161.19.3.3.13.9 | DisplayString | read-write | SNMP Trap IP Address 4. Format is either an IP address or DNS name. |
| STR trap5 | 1.3.6.1.4.1.161.19.3.3.13.10 | DisplayString | read-write | SNMP Trap IP Address 5. Format is either an IP address or DNS name. |
| STR trap6 | 1.3.6.1.4.1.161.19.3.3.13.11 | DisplayString | read-write | SNMP Trap IP Address 6. Format is either an IP address or DNS name. |
| STR trap7 | 1.3.6.1.4.1.161.19.3.3.13.12 | DisplayString | read-write | SNMP Trap IP Address 7. Format is either an IP address or DNS name. |
| STR trap8 | 1.3.6.1.4.1.161.19.3.3.13.13 | DisplayString | read-write | SNMP Trap IP Address 8. Format is either an IP address or DNS name. |
| STR trap9 | 1.3.6.1.4.1.161.19.3.3.13.14 | DisplayString | read-write | SNMP Trap IP Address 9. Format is either an IP address or DNS name. |
| STR trap10 | 1.3.6.1.4.1.161.19.3.3.13.15 | DisplayString | read-write | SNMP Trap IP Address 10. Format is either an IP address or DNS name. |
| whispBoxRFPhysical | 1.3.6.1.4.1.161.19.3.3.15 | |||
| whispBoxRFPhysicalRadios | 1.3.6.1.4.1.161.19.3.3.15.1 | not-accessible | Radio information table. | |
| whispBoxRFPhysicalRadioEntry | 1.3.6.1.4.1.161.19.3.3.15.1.1 | not-accessible | Radio information table entry. | |
| INT radioIndex | 1.3.6.1.4.1.161.19.3.3.15.1.1.1 | INTEGER | read-only | Radio Index. |
| INT radioType | 1.3.6.1.4.1.161.19.3.3.15.1.1.2 | INTEGER | read-only | Indicates if the radio is FSK or OFDM. |
| INT radioPaths | 1.3.6.1.4.1.161.19.3.3.15.1.1.3 | INTEGER | read-only | Indicates number of paths. For FSK or OFDM (non-MIMO), this is 1. For MIMO, it can be greater (with a current maximum of 2). |
| whispBoxRFPhysicalRadioPaths | 1.3.6.1.4.1.161.19.3.3.15.2 | not-accessible | Radio path information table. | |
| whispBoxRFPhysicalRadioPathEntry | 1.3.6.1.4.1.161.19.3.3.15.2.1 | not-accessible | Radio path table entry. | |
| INT pathIndex | 1.3.6.1.4.1.161.19.3.3.15.2.1.1 | INTEGER | read-only | Path Index. |
| whispBoxRFPhysicalRadioFrequencies | 1.3.6.1.4.1.161.19.3.3.15.3 | not-accessible | Available frequency information table. | |
| whispBoxRFPhysicalRadioFrequencyEntry | 1.3.6.1.4.1.161.19.3.3.15.3.1 | not-accessible | Available frequency table entry. | |
| INT frequency | 1.3.6.1.4.1.161.19.3.3.15.3.1.1 | INTEGER | read-only | Frequency. |
| whispBoxRFConfig | 1.3.6.1.4.1.161.19.3.3.16 | |||
| whispBoxRFConfigRadios | 1.3.6.1.4.1.161.19.3.3.16.1 | not-accessible | Radio configuration table. | |
| whispBoxRFConfigRadioEntry | 1.3.6.1.4.1.161.19.3.3.16.1.1 | not-accessible | Radio config table entry. | |
| INT radioConfigIndex | 1.3.6.1.4.1.161.19.3.3.16.1.1.1 | INTEGER | read-only | Radio Config Index. |
| INT radioFrequencyBand | 1.3.6.1.4.1.161.19.3.3.16.1.1.2 | INTEGER | read-only | Currently configured radio band. |
RFC description
Contains box-level management objects for Canopy wireless radio equipment including status, configuration, and event logs.
Start monitoring Cambium Networks Canopy fixed-wireless radios (RF sync/temperature/network-provisioning status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.