All MIBs › TRANGOP5830S-MU-MIB
Category: Wireless Backhaul
Description: Manages Trango P5830S master unit radio configuration, subscriber registration, and link management.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TRANGOP5830S-MU-MIB?
TRANGOP5830S-MU-MIB is a Trango Systems enterprise MIB for the P5830S master unit, a point-to-multipoint wireless radio product that manages subscriber unit registration and link configuration for its associated remote/subscriber radios. It exposes configuration and status data typical of a wireless master unit: radio parameters, the list/table of registered subscriber units, and per-link management settings. Given its role, it is expected to support hardware/software status monitoring of the radio link itself — signal quality, link/registration state of subscribers, and radio configuration — though no specific runtime object names were included in the available source excerpt to confirm exact identifiers. It complements the standard IF-MIB and general wireless-radio monitoring concepts rather than replacing them, being entirely Trango/P5830S-specific. It is deployed at a wireless base-station site managing multiple subscriber (customer) radios in a point-to-multipoint network, and administrators can download the TRANGOP5830S-MU-MIB file to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TRANGOP5830S-MU-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Trango P5830S wireless master unit radio
Monitoring Examples
No specific object or table names were provided in the source excerpt for this module, so concrete identifiers cannot be cited. Based on its purpose as a master-unit MIB, an administrator would typically poll a subscriber registration table to confirm which remote radios are currently registered and linked, and would check radio link-quality objects to catch a subscriber unit experiencing degraded signal before it drops offline entirely.
What Can Be Monitored
- subscriber unit registration status
- radio link configuration
- link quality/signal status
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| IpAddress | |
| enterprises |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| mibinfo | 1.3.6.1.4.1.5454.1.22.5 | |||
| STR mibinfoVersion | 1.3.6.1.4.1.5454.1.22.5.1 | DisplayString | read-only | Trango master unit MIB Version. |
| muipconfig | 1.3.6.1.4.1.5454.1.22.1.13 | |||
| IP muipconfigDefaultGateway | 1.3.6.1.4.1.5454.1.22.1.13.3 | IpAddress | read-write | New Default gateway. It will be saved to non-volatile memory and activated in 5 secs. |
| IP muipconfigIpAddress | 1.3.6.1.4.1.5454.1.22.1.13.1 | IpAddress | read-write | New IP address. It will be saved to non-volatile memory and activated in 5 secs. |
| IP muipconfigSubnet | 1.3.6.1.4.1.5454.1.22.1.13.2 | IpAddress | read-write | New Subnet mask. It will be saved to non-volatile memory and activated in 5 secs. |
| muism | 1.3.6.1.4.1.5454.1.22.2.5 | |||
| INT muismRxThreshold | 1.3.6.1.4.1.5454.1.22.2.5.4 | INTEGER | read-write | ISM RF rx threshold (in dBm). It specifies the receiver sensitivity of the master. By default, the radio's sensitivity is -82dBm. The higher the threshold is, the less sensitive the radio will be. In M5800S, the value -90 represents the rfrxthreshold is disabled. |
| INT muismTargetRSSI | 1.3.6.1.4.1.5454.1.22.2.5.5 | INTEGER | read-write | ISM RF RSSI (in dBm). It specifies the target RSSI from the remote unit to the master unit. Based on this parameter, the master unit can power level the remote unit so that it receives same level of signal strength from the remote unit, regardless far or near. Note that when you set the Target RSSI from the remote unit, you need to consider master unit's RF Rx Threshold value. The Target RSSI from the remote unit must be 5dB higher than the RF Rx Threshold. When the RF Rx Threshold is disabled, the setting of the Target RSSI from remote unit shall be no less than -75dBm. |
| INT muismTxPower | 1.3.6.1.4.1.5454.1.22.2.5.3 | INTEGER | read-write | ISM RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters muismTxPowerMax and masterismTxPowerMin for power setting range. |
| INT muismTxPowerMax | 1.3.6.1.4.1.5454.1.22.2.5.1 | INTEGER | read-only | The maximum ISM Tx power value can be set (in dBm). |
| INT muismTxPowerMin | 1.3.6.1.4.1.5454.1.22.2.5.2 | INTEGER | read-only | The minimum ISM Tx power value can be set (in dBm). |
| murf | 1.3.6.1.4.1.5454.1.22.2 | |||
| INT murfActiveChannel | 1.3.6.1.4.1.5454.1.22.2.2 | INTEGER | read-write | It specifies the current channel number the master unit operates on. |
| STR murfActivePolarization | 1.3.6.1.4.1.5454.1.22.2.3 | DisplayString | read-write | It specifies the current polarization the master unit operates on. |
| INT murfRSSI | 1.3.6.1.4.1.5454.1.22.2.1 | INTEGER | read-only | Remote unit RSSI (in dBm). |
| murftable | 1.3.6.1.4.1.5454.1.22.2.4 | |||
| INT murftableChannel1 | 1.3.6.1.4.1.5454.1.22.2.4.1 | INTEGER | read-write | RF channel 1 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel10 | 1.3.6.1.4.1.5454.1.22.2.4.10 | INTEGER | read-write | RF channel 10 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel11 | 1.3.6.1.4.1.5454.1.22.2.4.11 | INTEGER | read-write | RF channel 11 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel12 | 1.3.6.1.4.1.5454.1.22.2.4.12 | INTEGER | read-write | RF channel 12 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel13 | 1.3.6.1.4.1.5454.1.22.2.4.13 | INTEGER | read-write | RF channel 13 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel14 | 1.3.6.1.4.1.5454.1.22.2.4.14 | INTEGER | read-write | RF channel 14 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel15 | 1.3.6.1.4.1.5454.1.22.2.4.15 | INTEGER | read-write | RF channel 15 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel16 | 1.3.6.1.4.1.5454.1.22.2.4.16 | INTEGER | read-write | RF channel 16 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel17 | 1.3.6.1.4.1.5454.1.22.2.4.17 | INTEGER | read-write | RF channel 17 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel18 | 1.3.6.1.4.1.5454.1.22.2.4.18 | INTEGER | read-write | RF channel 18 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel19 | 1.3.6.1.4.1.5454.1.22.2.4.19 | INTEGER | read-write | RF channel 19 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel2 | 1.3.6.1.4.1.5454.1.22.2.4.2 | INTEGER | read-write | RF channel 2 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel20 | 1.3.6.1.4.1.5454.1.22.2.4.20 | INTEGER | read-write | RF channel 20 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel21 | 1.3.6.1.4.1.5454.1.22.2.4.21 | INTEGER | read-write | RF channel 21 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel22 | 1.3.6.1.4.1.5454.1.22.2.4.22 | INTEGER | read-write | RF channel 22 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel23 | 1.3.6.1.4.1.5454.1.22.2.4.23 | INTEGER | read-write | RF channel 23 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel24 | 1.3.6.1.4.1.5454.1.22.2.4.24 | INTEGER | read-write | RF channel 24 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel25 | 1.3.6.1.4.1.5454.1.22.2.4.25 | INTEGER | read-write | RF channel 25 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel26 | 1.3.6.1.4.1.5454.1.22.2.4.26 | INTEGER | read-write | RF channel 26 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel27 | 1.3.6.1.4.1.5454.1.22.2.4.27 | INTEGER | read-write | RF channel 27 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel28 | 1.3.6.1.4.1.5454.1.22.2.4.28 | INTEGER | read-write | RF channel 28 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel29 | 1.3.6.1.4.1.5454.1.22.2.4.29 | INTEGER | read-write | RF channel 29 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel3 | 1.3.6.1.4.1.5454.1.22.2.4.3 | INTEGER | read-write | RF channel 3 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel30 | 1.3.6.1.4.1.5454.1.22.2.4.30 | INTEGER | read-write | RF channel 30 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel4 | 1.3.6.1.4.1.5454.1.22.2.4.4 | INTEGER | read-write | RF channel 4 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel5 | 1.3.6.1.4.1.5454.1.22.2.4.5 | INTEGER | read-write | RF channel 5 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel6 | 1.3.6.1.4.1.5454.1.22.2.4.6 | INTEGER | read-write | RF channel 6 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel7 | 1.3.6.1.4.1.5454.1.22.2.4.7 | INTEGER | read-write | RF channel 7 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel8 | 1.3.6.1.4.1.5454.1.22.2.4.8 | INTEGER | read-write | RF channel 8 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT murftableChannel9 | 1.3.6.1.4.1.5454.1.22.2.4.9 | INTEGER | read-write | RF channel 9 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the master unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| muswitches | 1.3.6.1.4.1.5454.1.22.1.8 | |||
| INT muswitchesAutoPowerLevelRemoteUnit | 1.3.6.1.4.1.5454.1.22.1.8.7 | INTEGER | read-write | When it is turned on, then the master unit will command the remote unit to do power leveling. |
| INT muswitchesBlockBroadcastMulticast | 1.3.6.1.4.1.5454.1.22.1.8.1 | INTEGER | read-write | This switch enables or disables the blocking of Ethernet control packet except ICMP and ARP to reduce the amount of uneccessary overhead introduced to the wireless link. |
| INT muswitchesHTTPD | 1.3.6.1.4.1.5454.1.22.1.8.5 | INTEGER | read-write | When it is turned on, then the master unit is accessible for configuring via web browser (e.g. IE or Nescape). |
| musys | 1.3.6.1.4.1.5454.1.22.1 | |||
| INT musysActivateOpmode | 1.3.6.1.4.1.5454.1.22.1.5 | INTEGER | read-write | Engage master unit to on operation mode. |
| INT musysCurOpMode | 1.3.6.1.4.1.5454.1.22.1.4 | INTEGER | read-only | Master unit's current operation mode. |
| INT musysDefOpMode | 1.3.6.1.4.1.5454.1.22.1.3 | INTEGER | read-write | The operation mode (on or off) the master unit is on after reboot/power cycle. |
| OCT musysDeviceId | 1.3.6.1.4.1.5454.1.22.1.2 | OCTET STRING | read-only | Master unit device Id. Each master unit in a cluster shall have unique ID. |
| STR musysReadCommStr | 1.3.6.1.4.1.5454.1.22.1.6 | DisplayString | read-write | SNMP agent read community string. It is used for authentication purpose. |
| INT musysReboot | 1.3.6.1.4.1.5454.1.22.1.12 | INTEGER | read-write | Reboot the master unit. |
| INT musysTemperature | 1.3.6.1.4.1.5454.1.22.1.10 | INTEGER | read-only | Current master unit's temperature value (in Celsius). |
| INT musysUpdateFlashAndActivate | 1.3.6.1.4.1.5454.1.22.1.11 | INTEGER | read-write | Save system setting values to Flash and activate the settings. |
| STR musysWriteCommStr | 1.3.6.1.4.1.5454.1.22.1.7 | DisplayString | read-write | SNMP agent write community string. It is used for authentication purpose. |
| mutraffic | 1.3.6.1.4.1.5454.1.22.1.9 | |||
| CTR mutrafficEthInOctets | 1.3.6.1.4.1.5454.1.22.1.9.1 | Counter | read-only | Number of payload octets received on Ethernet port. |
| CTR mutrafficEthOutOctets | 1.3.6.1.4.1.5454.1.22.1.9.2 | Counter | read-only | Number of payload octets transmitted on Ethernet port. |
| CTR mutrafficRfInOctets | 1.3.6.1.4.1.5454.1.22.1.9.3 | Counter | read-only | Number of octets of remote's payload received from RF port. |
| CTR mutrafficRfOutOctets | 1.3.6.1.4.1.5454.1.22.1.9.4 | Counter | read-only | Number of octets of remote's payload transmitted to RF port. |
| muunii | 1.3.6.1.4.1.5454.1.22.2.6 | |||
| INT muuniiRxThreshold | 1.3.6.1.4.1.5454.1.22.2.6.4 | INTEGER | read-write | This object is only applicable to M5830S/P5830S radio. UNII RF rx threshold (in dBm). It specifies the receiver sensitivity of the master. |
| INT muuniiTargetRSSI | 1.3.6.1.4.1.5454.1.22.2.6.5 | INTEGER | read-write | This object is only applicable to M5830S/P5830S radio. UNII RF target RSSI (in dBm). It specifies the target RSSI from remote unit to the master unit. Based on this parameter, the master can power level the remote unit so that it receives same level of signal strength from the remote unit, regardless far or near. Note that when you set the Target RSSI from the remote unit, you need to consider remote unit's RF Rx Threshold value. The Target RSSI from the remote unit must be 5dB higher than the RF Rx Threshold. |
| INT muuniiTxPower | 1.3.6.1.4.1.5454.1.22.2.6.3 | INTEGER | read-write | This object is only applicable to M5830S/P5830S radio. UNII RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters apuniiTxPowerMax and apuniiTxPowerMin for power setting range. |
| INT muuniiTxPowerMax | 1.3.6.1.4.1.5454.1.22.2.6.1 | INTEGER | read-only | This object is only applicable to M5830S/P5830S radio. The maximum UNII Tx power value can be set (in dBm). |
| INT muuniiTxPowerMin | 1.3.6.1.4.1.5454.1.22.2.6.2 | INTEGER | read-only | This object is only applicable to M5830S/P5830S radio. The minimum UNII Tx power value can be set (in dBm). |
| muversion | 1.3.6.1.4.1.5454.1.22.1.1 | |||
| OCT muversionFPGA | 1.3.6.1.4.1.5454.1.22.1.1.3 | OCTET STRING | read-only | FPGA firmware version. |
| OCT muversionFPGAChecksum | 1.3.6.1.4.1.5454.1.22.1.1.5 | OCTET STRING | read-only | Master unit FPGA checksum. |
| STR muversionFW | 1.3.6.1.4.1.5454.1.22.1.1.2 | DisplayString | read-only | Main firmware version. Format: HD. |
| OCT muversionFWChecksum | 1.3.6.1.4.1.5454.1.22.1.1.4 | OCTET STRING | read-only | Master unit firmware checksum. |
| OCT muversionHW | 1.3.6.1.4.1.5454.1.22.1.1.1 | OCTET STRING | read-only | Hardware version. |
| p5830smu | 1.3.6.1.4.1.5454.1.22 | |||
| INT remoteDownstreamMIR | 1.3.6.1.4.1.5454.1.22.3.3 | INTEGER | read-write | It is the Maximum Information Rate (in Kbps) the master unit allocates to the remote unit. |
| ru | 1.3.6.1.4.1.5454.1.22.3 | |||
| INT ruAssociation | 1.3.6.1.4.1.5454.1.22.3.6 | INTEGER | read-only | Remote unit association status. |
| OCT ruDeviceId | 1.3.6.1.4.1.5454.1.22.3.1 | OCTET STRING | read-write | Remote unit device ID. |
| INT ruDistance | 1.3.6.1.4.1.5454.1.22.3.7 | INTEGER | read-only | Distance of remote unit (in mile). |
| INT ruPowerLvl | 1.3.6.1.4.1.5454.1.22.3.4 | INTEGER | read-write | It is a feature that is typically found in more elaborate mobile systems such as cellular CDMA networks. Using this feature, the remote unit have its RF power output adjusted until its signal strength received in the master unit is roughly the same. |
| INT ruReboot | 1.3.6.1.4.1.5454.1.22.3.5 | INTEGER | read-write | Master unit issues reboot command to remote unit. |
| INT ruUpstreamMIR | 1.3.6.1.4.1.5454.1.22.3.2 | INTEGER | read-write | It is the Maximum Information Rate (in Kbps) the master unit allocates to remote unit. |
| tbw | 1.3.6.1.4.1.5454.1 | |||
| trango | 1.3.6.1.4.1.5454 | |||
| trapconfig | 1.3.6.1.4.1.5454.1.22.4 | |||
| IP trapconfigDest1IPAddress | 1.3.6.1.4.1.5454.1.22.4.2 | IpAddress | read-write | Trap destination 1 IP address. |
| IP trapconfigDest2IPAddress | 1.3.6.1.4.1.5454.1.22.4.3 | IpAddress | read-write | Trap destination 2 IP address. |
RFC description
Trango Systems OP5830S master unit MIB for managing and monitoring Trango wireless backhaul equipment configuration and performance metrics.
Start monitoring Trango P5830S wireless master unit radio (subscriber-unit registration/link status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.