All MIBs › TRANGOP5830S-RU-MIB
Category: Wireless Backhaul
Description: Manages Trango P5830S remote unit radio configuration, association state, and link quality statistics.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TRANGOP5830S-RU-MIB?
TRANGOP5830S-RU-MIB is a Trango Systems MIB for the P5830S remote unit, a subscriber-side wireless radio used in Trango's point-to-point or point-to-multipoint wireless links. It is described as covering radio configuration, association state, and link quality statistics for the remote unit. Its monitoring purpose centers on hardware/link status: confirming the remote radio has associated with its base station and tracking link-quality metrics that reveal a degraded or dropped RF connection. As a vendor-specific radio MIB it stands alongside other Trango Apex/P-series MIBs in the same family, sharing similar conventions for radio status reporting. It is deployed on Trango P5830S subscriber/remote radios in fixed wireless access and backhaul networks operated by WISPs, who rely on the TRANGOP5830S-RU-MIB MIB to poll association and link-quality status remotely.
IPNetwork Monitor allows you to monitor SNMP objects defined in TRANGOP5830S-RU-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Trango Systems P5830S remote/subscriber wireless radio
Monitoring Examples
No sample object names were provided for this module, so specific object identifiers cannot be cited here. Based on its description, an admin would typically poll the remote unit's association-state object to confirm it is currently linked to its base station, and link-quality counters (such as signal level or error-rate statistics) to detect a weak or unstable connection. A radio reporting a non-associated state or a marked drop in link quality would indicate an antenna alignment problem or RF interference affecting the subscriber link.
What Can Be Monitored
- radio association state
- link quality statistics
- radio configuration parameters
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| IpAddress | |
| enterprises |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| mibinfo | 1.3.6.1.4.1.5454.1.24.5 | |||
| STR mibinfoVersion | 1.3.6.1.4.1.5454.1.24.5.1 | DisplayString | read-only | Trango remote unit MIB Version. |
| p5830sru | 1.3.6.1.4.1.5454.1.24 | |||
| ruipconfig | 1.3.6.1.4.1.5454.1.24.1.13 | |||
| IP ruipconfigDefaultGateway | 1.3.6.1.4.1.5454.1.24.1.13.3 | IpAddress | read-write | New Default gateway. It will be saved to non-volatile memory and activated in 5 secs. |
| IP ruipconfigIpAddress | 1.3.6.1.4.1.5454.1.24.1.13.1 | IpAddress | read-write | New IP address. It will be saved to non-volatile memory and activated in 5 secs. |
| IP ruipconfigSubnet | 1.3.6.1.4.1.5454.1.24.1.13.2 | IpAddress | read-write | New Subnet mask. It will be saved to non-volatile memory and activated in 5 secs. |
| ruism | 1.3.6.1.4.1.5454.1.24.2.5 | |||
| INT ruismRxThreshold | 1.3.6.1.4.1.5454.1.24.2.5.4 | INTEGER | read-write | ISM RF rx threshold (in dBm). It specifies the receiver sensitivity of the remote. By default, the radio's sensitivity is -82dBm. The higher the threshold is, the less sensitive the radio will be. In M5800S, the value -90 represents the rfrxthreshold is disabled. |
| INT ruismTxPower | 1.3.6.1.4.1.5454.1.24.2.5.3 | INTEGER | read-write | ISM RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters remoteismTxPowerMax and remoteismTxPowerMin for power setting range. |
| INT ruismTxPowerMax | 1.3.6.1.4.1.5454.1.24.2.5.1 | INTEGER | read-only | The maximum ISM Tx power value can be set (in dBm). |
| INT ruismTxPowerMin | 1.3.6.1.4.1.5454.1.24.2.5.2 | INTEGER | read-only | The minimum ISM Tx power value can be set (in dBm). |
| rurf | 1.3.6.1.4.1.5454.1.24.2 | |||
| INT rurfRSSI | 1.3.6.1.4.1.5454.1.24.2.1 | INTEGER | read-only | Remote unit RSSI (in dBm). |
| rurftable | 1.3.6.1.4.1.5454.1.24.2.4 | |||
| INT rurftableChannel1 | 1.3.6.1.4.1.5454.1.24.2.4.1 | INTEGER | read-write | RF channel 1 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel10 | 1.3.6.1.4.1.5454.1.24.2.4.10 | INTEGER | read-write | RF channel 10 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel11 | 1.3.6.1.4.1.5454.1.24.2.4.11 | INTEGER | read-write | RF channel 11 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel12 | 1.3.6.1.4.1.5454.1.24.2.4.12 | INTEGER | read-write | RF channel 12 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel13 | 1.3.6.1.4.1.5454.1.24.2.4.13 | INTEGER | read-write | RF channel 13 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel14 | 1.3.6.1.4.1.5454.1.24.2.4.14 | INTEGER | read-write | RF channel 14 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel15 | 1.3.6.1.4.1.5454.1.24.2.4.15 | INTEGER | read-write | RF channel 15 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel16 | 1.3.6.1.4.1.5454.1.24.2.4.16 | INTEGER | read-write | RF channel 16 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel17 | 1.3.6.1.4.1.5454.1.24.2.4.17 | INTEGER | read-write | RF channel 17 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel18 | 1.3.6.1.4.1.5454.1.24.2.4.18 | INTEGER | read-write | RF channel 18 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel19 | 1.3.6.1.4.1.5454.1.24.2.4.19 | INTEGER | read-write | RF channel 19 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel2 | 1.3.6.1.4.1.5454.1.24.2.4.2 | INTEGER | read-write | RF channel 2 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel20 | 1.3.6.1.4.1.5454.1.24.2.4.20 | INTEGER | read-write | RF channel 20 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel21 | 1.3.6.1.4.1.5454.1.24.2.4.21 | INTEGER | read-write | RF channel 21 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel22 | 1.3.6.1.4.1.5454.1.24.2.4.22 | INTEGER | read-write | RF channel 22 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel23 | 1.3.6.1.4.1.5454.1.24.2.4.23 | INTEGER | read-write | RF channel 23 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel24 | 1.3.6.1.4.1.5454.1.24.2.4.24 | INTEGER | read-write | RF channel 24 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel25 | 1.3.6.1.4.1.5454.1.24.2.4.25 | INTEGER | read-write | RF channel 25 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel26 | 1.3.6.1.4.1.5454.1.24.2.4.26 | INTEGER | read-write | RF channel 26 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel27 | 1.3.6.1.4.1.5454.1.24.2.4.27 | INTEGER | read-write | RF channel 27 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel28 | 1.3.6.1.4.1.5454.1.24.2.4.28 | INTEGER | read-write | RF channel 28 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel29 | 1.3.6.1.4.1.5454.1.24.2.4.29 | INTEGER | read-write | RF channel 29 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel3 | 1.3.6.1.4.1.5454.1.24.2.4.3 | INTEGER | read-write | RF channel 3 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel30 | 1.3.6.1.4.1.5454.1.24.2.4.30 | INTEGER | read-write | RF channel 30 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel4 | 1.3.6.1.4.1.5454.1.24.2.4.4 | INTEGER | read-write | RF channel 4 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel5 | 1.3.6.1.4.1.5454.1.24.2.4.5 | INTEGER | read-write | RF channel 5 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel6 | 1.3.6.1.4.1.5454.1.24.2.4.6 | INTEGER | read-write | RF channel 6 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel7 | 1.3.6.1.4.1.5454.1.24.2.4.7 | INTEGER | read-write | RF channel 7 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel8 | 1.3.6.1.4.1.5454.1.24.2.4.8 | INTEGER | read-write | RF channel 8 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| INT rurftableChannel9 | 1.3.6.1.4.1.5454.1.24.2.4.9 | INTEGER | read-write | RF channel 9 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the remote unit. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S/P5830S radio. |
| ruswitches | 1.3.6.1.4.1.5454.1.24.1.8 | |||
| INT ruswitchesAutoScanMasterSignal | 1.3.6.1.4.1.5454.1.24.1.8.6 | INTEGER | read-write | This switch enables or disables the auto scan master unit signal operation on the remote unit only. |
| INT ruswitchesBlockBroadcastMulticast | 1.3.6.1.4.1.5454.1.24.1.8.1 | INTEGER | read-write | This switch enables or disables the blocking of Ethernet control packet except ICMP and ARP to reduce the amount of uneccessary overhead introduced to the wireless link. |
| INT ruswitchesHTTPD | 1.3.6.1.4.1.5454.1.24.1.8.5 | INTEGER | read-write | When it is turned on, then the remote unit is accessible for configuring via web browser (e.g. IE or Nescape). |
| rusys | 1.3.6.1.4.1.5454.1.24.1 | |||
| INT rusysActivateOpmode | 1.3.6.1.4.1.5454.1.24.1.5 | INTEGER | read-write | Engage remote unit to on operation mode. |
| INT rusysCurOpMode | 1.3.6.1.4.1.5454.1.24.1.4 | INTEGER | read-only | Remote unit's current operation mode. |
| INT rusysDefOpMode | 1.3.6.1.4.1.5454.1.24.1.3 | INTEGER | read-write | The operation mode (on or off) the remote unit is on after reboot/power cycle. |
| OCT rusysDeviceId | 1.3.6.1.4.1.5454.1.24.1.2 | OCTET STRING | read-only | Remote unit device Id. Each remote unit in a cluster shall have unique ID. |
| STR rusysReadCommStr | 1.3.6.1.4.1.5454.1.24.1.6 | DisplayString | read-write | SNMP agent read community string. It is used for authenticcation purpose. |
| INT rusysReboot | 1.3.6.1.4.1.5454.1.24.1.12 | INTEGER | read-write | Reboot the remote unit. |
| INT rusysTemperature | 1.3.6.1.4.1.5454.1.24.1.10 | INTEGER | read-only | Current remote unit temperature value (in Celsius). |
| INT rusysUpdateFlashAndActivate | 1.3.6.1.4.1.5454.1.24.1.11 | INTEGER | read-write | Save system setting values to Flash and activate the settings. |
| STR rusysWriteCommStr | 1.3.6.1.4.1.5454.1.24.1.7 | DisplayString | read-write | SNMP agent write community string. It is used for authentication purpose. |
| rutraffic | 1.3.6.1.4.1.5454.1.24.1.9 | |||
| CTR rutrafficEthInOctets | 1.3.6.1.4.1.5454.1.24.1.9.1 | Counter | read-only | Number of octets of remote unit's payload received on Ethernet port. |
| CTR rutrafficEthOutOctets | 1.3.6.1.4.1.5454.1.24.1.9.2 | Counter | read-only | Number of octets of remote unit's payload transmitted on Ethernet port. |
| CTR rutrafficRfInOctets | 1.3.6.1.4.1.5454.1.24.1.9.3 | Counter | read-only | Number of octets of remote unit's payload received from RF port. |
| CTR rutrafficRfOutOctets | 1.3.6.1.4.1.5454.1.24.1.9.4 | Counter | read-only | Number of octets of remote unit's payload transmitted to RF port. |
| ruunii | 1.3.6.1.4.1.5454.1.24.2.6 | |||
| INT ruuniiRxThreshold | 1.3.6.1.4.1.5454.1.24.2.6.4 | INTEGER | read-write | This object is only applicable to M5830S/P5830S radio. UNII RF rx threshold (in dBm). It specifies the receiver sensitivity of the master unit. |
| INT ruuniiTxPower | 1.3.6.1.4.1.5454.1.24.2.6.3 | INTEGER | read-write | This object is only applicable to M5830S/P5830S radio. UNII RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters apuniiTxPowerMax and apuniiTxPowerMin for power setting range. |
| INT ruuniiTxPowerMax | 1.3.6.1.4.1.5454.1.24.2.6.1 | INTEGER | read-only | This object is only applicable to M5830S/P5830S radio. The maximum UNII Tx power value can be set (in dBm). |
| INT ruuniiTxPowerMin | 1.3.6.1.4.1.5454.1.24.2.6.2 | INTEGER | read-only | This object is only applicable to M5830S/P5830S radio. The minimum UNII Tx power value can be set (in dBm). |
| ruversion | 1.3.6.1.4.1.5454.1.24.1.1 | |||
| OCT ruversionFPGA | 1.3.6.1.4.1.5454.1.24.1.1.3 | OCTET STRING | read-only | FPGA firmware version. |
| OCT ruversionFPGAChecksum | 1.3.6.1.4.1.5454.1.24.1.1.5 | OCTET STRING | read-only | Remote unit FPGA checksum. |
| STR ruversionFW | 1.3.6.1.4.1.5454.1.24.1.1.2 | DisplayString | read-only | Main firmware version. Format: HD. |
| OCT ruversionFWChecksum | 1.3.6.1.4.1.5454.1.24.1.1.4 | OCTET STRING | read-only | Remote unit firmware checksum. |
| OCT ruversionHW | 1.3.6.1.4.1.5454.1.24.1.1.1 | OCTET STRING | read-only | Hardware version. |
| tbw | 1.3.6.1.4.1.5454.1 | |||
| trango | 1.3.6.1.4.1.5454 |
RFC description
Vendor management MIB for Transition Networks TRANGOP5830S RU (Remote Unit) fiber/optical equipment.
Start monitoring Trango Systems P5830S remote/subscriber wireless radio (association/link-quality status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.