TRANGOM5800S-MIB

All MIBs › TRANGOM5800S-MIB

Category: Wireless Backhaul

Description:

Manages Trango M5800S point-to-multipoint wireless backhaul radio configuration and link statistics.

Imported Objects

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
IpAddress
enterprises

What Is TRANGOM5800S-MIB?

TRANGOM5800S-MIB is a Trango Systems (enterprise OID 5454) proprietary MIB for the M5800S fixed-wireless access-point platform, reporting radio and operating-mode configuration alongside throughput logging. Its objects cover hardware/firmware/FPGA version, checksum, device/base/AP ID, default/current operating mode and activation trigger, IP address/subnet/gateway, read/write community strings, broadcast/multicast blocking, subscriber-unit-to-subscriber-unit (SU-to-SU) flag, TFTP/HTTP daemon enable, MIR (Minimum Information Rate) threshold, and Ethernet/RF receive/transmit average-throughput logs and octet counters. As a configuration/performance MIB it lets an administrator confirm operating mode and watch RF vs. Ethernet throughput trends on a Trango M5800S access point. It is deployed on Trango Systems M5800S fixed-wireless access points. Engineers can download the TRANGOM5800S-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in TRANGOM5800S-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

operating mode and RF/Ethernet throughput trends

Supported Devices

Trango Systems M5800S fixed-wireless access points

Monitoring Examples

An administrator compares apsysRfRxAvgThroughputLog against apsysEthRxAvgThroughputLog to identify whether a throughput bottleneck is on the RF or Ethernet side of a Trango M5800S access point.

OIDs

OID symbolic	OID numeric	Type	Access	Description
apism	1.3.6.1.4.1.5454.1.10.2.4
NTF apOpModeFailure	1.3.6.1.4.1.5454.1.10.16.0.9			The SNMP trap that is generated when a specific AP not being in ap mode during boot up sequence.
aprf	1.3.6.1.4.1.5454.1.10.2
INT aprfActiveChannel	1.3.6.1.4.1.5454.1.10.2.1	INTEGER	read-write	It specifies the current channel number the radio operates on.
STR aprfActivePolarization	1.3.6.1.4.1.5454.1.10.2.2	DisplayString	read-write	It specifies the current polarization the radio operates on.
INT aprfChannel1	1.3.6.1.4.1.5454.1.10.2.3.1	INTEGER	read-write	RF channel 1 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel10	1.3.6.1.4.1.5454.1.10.2.3.10	INTEGER	read-write	RF channel 10 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel11	1.3.6.1.4.1.5454.1.10.2.3.11	INTEGER	read-write	RF channel 11 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel12	1.3.6.1.4.1.5454.1.10.2.3.12	INTEGER	read-write	RF channel 12 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel13	1.3.6.1.4.1.5454.1.10.2.3.13	INTEGER	read-write	RF channel 13 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel14	1.3.6.1.4.1.5454.1.10.2.3.14	INTEGER	read-write	RF channel 14 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel15	1.3.6.1.4.1.5454.1.10.2.3.15	INTEGER	read-write	RF channel 15 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel16	1.3.6.1.4.1.5454.1.10.2.3.16	INTEGER	read-write	RF channel 16 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel17	1.3.6.1.4.1.5454.1.10.2.3.17	INTEGER	read-write	RF channel 17 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel18	1.3.6.1.4.1.5454.1.10.2.3.18	INTEGER	read-write	RF channel 18 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel19	1.3.6.1.4.1.5454.1.10.2.3.19	INTEGER	read-write	RF channel 19 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel2	1.3.6.1.4.1.5454.1.10.2.3.2	INTEGER	read-write	RF channel 2 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel20	1.3.6.1.4.1.5454.1.10.2.3.20	INTEGER	read-write	RF channel 20 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel21	1.3.6.1.4.1.5454.1.10.2.3.21	INTEGER	read-write	RF channel 21 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel22	1.3.6.1.4.1.5454.1.10.2.3.22	INTEGER	read-write	RF channel 22 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel23	1.3.6.1.4.1.5454.1.10.2.3.23	INTEGER	read-write	RF channel 23 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel24	1.3.6.1.4.1.5454.1.10.2.3.24	INTEGER	read-write	RF channel 24 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel25	1.3.6.1.4.1.5454.1.10.2.3.25	INTEGER	read-write	RF channel 25 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel26	1.3.6.1.4.1.5454.1.10.2.3.26	INTEGER	read-write	RF channel 26 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel27	1.3.6.1.4.1.5454.1.10.2.3.27	INTEGER	read-write	RF channel 27 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel28	1.3.6.1.4.1.5454.1.10.2.3.28	INTEGER	read-write	RF channel 28 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel29	1.3.6.1.4.1.5454.1.10.2.3.29	INTEGER	read-write	RF channel 29 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel3	1.3.6.1.4.1.5454.1.10.2.3.3	INTEGER	read-write	RF channel 3 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel30	1.3.6.1.4.1.5454.1.10.2.3.30	INTEGER	read-write	RF channel 30 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel4	1.3.6.1.4.1.5454.1.10.2.3.4	INTEGER	read-write	RF channel 4 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel5	1.3.6.1.4.1.5454.1.10.2.3.5	INTEGER	read-write	RF channel 5 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel6	1.3.6.1.4.1.5454.1.10.2.3.6	INTEGER	read-write	RF channel 6 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel7	1.3.6.1.4.1.5454.1.10.2.3.7	INTEGER	read-write	RF channel 7 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel8	1.3.6.1.4.1.5454.1.10.2.3.8	INTEGER	read-write	RF channel 8 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel9	1.3.6.1.4.1.5454.1.10.2.3.9	INTEGER	read-write	RF channel 9 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfismRxThreshold	1.3.6.1.4.1.5454.1.10.2.4.5	INTEGER	read-write	ISM RF rx threshold (in dBm). It specifies the receiver sensitivity of the AP. By default, the radio's sensitivity is -82dBm. The higher the threshold is, the less sensitive the radio will be. In M5800S, the value -90 represents the rfrxthreshold is disabled.
INT aprfismServiceRadius	1.3.6.1.4.1.5454.1.10.2.4.4	INTEGER	read-write	ISM RF service radius (in mile). It specifies the distance of the furthest SU the AP will serve. Based on this information, the AP will determine the maximum wait time for a SU to response to a poll before it starts to poll the next one.
INT aprfismTargetRSSI	1.3.6.1.4.1.5454.1.10.2.4.6	INTEGER	read-write	ISM RF target RSSI (in dBm). It specifies the target RSSI from all SUs to the AP. Based on this parameter, the AP can power level each SU so that it receives same level of signal strength from all SUs, regardless far or near. Note that when you set the Target RSSI from SU, you need to consider AP's RF Rx Threshold value. The Target RSSI from SU must be 5dB higher than the RF Rx Threshold. When the RF Rx Threshold is disabled, the setting of the Target RSSI from SU shall be no less than -75dBm.
INT aprfismTxPower	1.3.6.1.4.1.5454.1.10.2.4.3	INTEGER	read-write	ISM RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters aprfismTxPowerMax and aprfismTxPowerMin for power setting range.
INT aprfismTxPowerMax	1.3.6.1.4.1.5454.1.10.2.4.1	INTEGER	read-only	The maximum ISM Tx power value can be set (in dBm).
INT aprfismTxPowerMin	1.3.6.1.4.1.5454.1.10.2.4.2	INTEGER	read-only	The minimum ISM Tx power value can be set (in dBm).
aprftable	1.3.6.1.4.1.5454.1.10.2.3
INT aprfuniiRxThreshold	1.3.6.1.4.1.5454.1.10.2.5.5	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF rx threshold (in dBm). It specifies the receiver sensitivity of the AP.
INT aprfuniiServiceRadius	1.3.6.1.4.1.5454.1.10.2.5.4	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF service radius (in mile). It specifies the distance of the furthest SU the AP will serve. Based on this information, the AP will determine the maximum wait time for a SU to response to a poll before it starts to poll the next one.
INT aprfuniiTargetRSSI	1.3.6.1.4.1.5454.1.10.2.5.6	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF target RSSI (in dBm). It specifies the target RSSI from all SUs to the AP. Based on this parameter, the AP can power level each SU so that it receives same level of signal strength from all SUs, regardless far or near. Note that when you set the Target RSSI from SU, you need to consider AP's RF Rx Threshold value. The Target RSSI from SU must be 5dB higher than the RF Rx Threshold.
INT aprfuniiTxPower	1.3.6.1.4.1.5454.1.10.2.5.3	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters aprfuniiTxPowerMax and aprfuniiTxPowerMin for power setting range.
INT aprfuniiTxPowerMax	1.3.6.1.4.1.5454.1.10.2.5.1	INTEGER	read-only	This object is only applicable to M5830S radio. The maximum UNII Tx power value can be set (in dBm).
INT aprfuniiTxPowerMin	1.3.6.1.4.1.5454.1.10.2.5.2	INTEGER	read-only	This object is only applicable to M5830S radio. The minimum UNII Tx power value can be set (in dBm).
apswitches	1.3.6.1.4.1.5454.1.10.1.13
INT apsysActivateOpmode	1.3.6.1.4.1.5454.1.10.1.7	INTEGER	read-write	Engage AP unit to ap operation mode.
INT apsysAPId	1.3.6.1.4.1.5454.1.10.1.4	INTEGER	read-write	AP ID. Each AP in a cluster shall have unique AP ID.
INT apsysBaseId	1.3.6.1.4.1.5454.1.10.1.3	INTEGER	read-write	Cluster that the AP belongs to. All APs and SUs in the same cluster shall have the same Base ID.
INT apsysBlockBroadcastMulticast	1.3.6.1.4.1.5454.1.10.1.13.1	INTEGER	read-write	This switch enables or disables the blocking of Ethernet control packet except ICMP and ARP to reduce the amount of uneccessary overhead introduced to the wireless link.
OCT apsysChecksum	1.3.6.1.4.1.5454.1.10.1.1.4	OCTET STRING	read-only	AP firmware checksum.
INT apsysCurOpMode	1.3.6.1.4.1.5454.1.10.1.6	INTEGER	read-only	Radio's current operation mode.
IP apsysDefaultGateway	1.3.6.1.4.1.5454.1.10.1.10	IpAddress	read-write	Default gateway.
INT apsysDefOpMode	1.3.6.1.4.1.5454.1.10.1.5	INTEGER	read-write	The operation mode (ap or off) the radio is on after reboot/power cycle.
OCT apsysDeviceId	1.3.6.1.4.1.5454.1.10.1.2	OCTET STRING	read-only	MAC address.
CTR apsysEthInOctets	1.3.6.1.4.1.5454.1.10.1.15.5	Counter	read-only	Number of payload octets received on Ethernet port.
CTR apsysEthOutOctets	1.3.6.1.4.1.5454.1.10.1.15.6	Counter	read-only	Number of payload octets transmitted on Ethernet port.
INT apsysEthRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.1	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on Ethernet port over the last 60 seconds.
INT apsysEthTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.2	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on Ethernet port over the last 60 seconds.
OCT apsysFPGA	1.3.6.1.4.1.5454.1.10.1.1.3	OCTET STRING	read-only	FPGA firmware version.
STR apsysFW	1.3.6.1.4.1.5454.1.10.1.1.2	DisplayString	read-only	Main firmware version. Format: HD.
INT apsysHTTPD	1.3.6.1.4.1.5454.1.10.1.13.5	INTEGER	read-write	When it is turned on, then the AP is accessible for configuring via web browser (e.g. IE or Nescape).
OCT apsysHW	1.3.6.1.4.1.5454.1.10.1.1.1	OCTET STRING	read-only	Hardware version.
IP apsysIPAddr	1.3.6.1.4.1.5454.1.10.1.8	IpAddress	read-write	IP address.
INT apsysMIRThreshold	1.3.6.1.4.1.5454.1.10.1.14	INTEGER	read-write	Maximum Information Rate (in Kbps), the AP allows the network to utilize before enforcing CIR on each subscriber.
STR apsysReadCommStr	1.3.6.1.4.1.5454.1.10.1.11	DisplayString	read-write	SNMP agent read community string. It is used for authentication purpose.
INT apsysReboot	1.3.6.1.4.1.5454.1.10.1.18	INTEGER	read-write	Reboot the radio.
CTR apsysRfInOctets	1.3.6.1.4.1.5454.1.10.1.15.7	Counter	read-only	Number of octets of SUs payload received from RF port.
CTR apsysRfOutOctets	1.3.6.1.4.1.5454.1.10.1.15.8	Counter	read-only	Number of octets of SUs payload transmitted to RF port.
INT apsysRfRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.3	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on RF port over the last 60 seconds.
INT apsysRfTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.4	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on RF port over the last 60 seconds.
IP apsysSubnet	1.3.6.1.4.1.5454.1.10.1.9	IpAddress	read-write	Subnet mask.
INT apsysSUtoSU	1.3.6.1.4.1.5454.1.10.1.13.2	INTEGER	read-write	This switch enables or disables the peer-to-peer feature among SUs through the AP. Before this switch is turned on, all SUs that want to communicate with each other have to be assigned to the same group.
apsystem	1.3.6.1.4.1.5454.1.10.1
INT apsysTemperature	1.3.6.1.4.1.5454.1.10.1.16	INTEGER	read-only	Current AP temperature value (in Celsius).
INT apsysTFTPD	1.3.6.1.4.1.5454.1.10.1.13.4	INTEGER	read-write	This switch enables or disables the TFTP operation. When it is turned on, then the AP will be ready for code download.
INT apsysUpdateFlashAndActivate	1.3.6.1.4.1.5454.1.10.1.17	INTEGER	read-write	Save system setting values to Flash and activate the settings.
STR apsysWriteCommStr	1.3.6.1.4.1.5454.1.10.1.12	DisplayString	read-write	SNMP agent write community string. It is used for authentication purpose.
aptraffic	1.3.6.1.4.1.5454.1.10.1.15
STR aptrpCommStr	1.3.6.1.4.1.5454.1.10.4.4.1.3	DisplayString	read-write	Specific trap community string.
INT aptrpCount	1.3.6.1.4.1.5454.1.10.4.1	INTEGER	read-only	Types of trap.
IP aptrpDest1IPAddress	1.3.6.1.4.1.5454.1.10.4.2	IpAddress	read-write	Trap destination 1 IP address.
IP aptrpDest2IPAddress	1.3.6.1.4.1.5454.1.10.4.3	IpAddress	read-write	Trap destination 2 IP address.
INT aptrpEnable	1.3.6.1.4.1.5454.1.10.4.4.1.4	INTEGER	read-write	Enable a specific Trango trap event or not.
aptrpEntry	1.3.6.1.4.1.5454.1.10.4.4.1		not-accessible	Information about a specific Trango trap event.
INT aptrpID	1.3.6.1.4.1.5454.1.10.4.4.1.2	INTEGER	read-only	Specific trap ID.
INT aptrpIndex	1.3.6.1.4.1.5454.1.10.4.4.1.1	INTEGER	read-only	Trap index.
aptrpTable	1.3.6.1.4.1.5454.1.10.4.4		not-accessible	A table that contains information of Trango trap events .
apunii	1.3.6.1.4.1.5454.1.10.2.5
apversion	1.3.6.1.4.1.5454.1.10.1.1
m5800sap	1.3.6.1.4.1.5454.1.10
m5800straps	1.3.6.1.4.1.5454.1.10.16
mibinfo	1.3.6.1.4.1.5454.1.10.5
STR mibinfoVersion	1.3.6.1.4.1.5454.1.10.5.1	DisplayString	read-only	Trango MIB Version.
su	1.3.6.1.4.1.5454.1.10.3
INT suAdd	1.3.6.1.4.1.5454.1.10.3.5.7	INTEGER	read-write	Add a subscriber (specified in object suAddOrDeleteID) to the subscriber database.
INT suAddCIR	1.3.6.1.4.1.5454.1.10.3.5.5	INTEGER	read-write	It is the Committed Information Rate (in Kbps) the AP allocates to SU.
OCT suAddMAC	1.3.6.1.4.1.5454.1.10.3.5.2	OCTET STRING	read-write	It is the MAC address of the subscriber unit, which can be found on the back of the SU.
INT suAddMIR	1.3.6.1.4.1.5454.1.10.3.5.6	INTEGER	read-write	It is the Maximum Information Rate (in Kbps) the AP allocates to SU.
INT suAddOrDeleteID	1.3.6.1.4.1.5454.1.10.3.5.1	INTEGER	read-write	Subscriber unit ID (1..8190). Each subscriber in a sector shall have a unique ID.
INT suAddPolling	1.3.6.1.4.1.5454.1.10.3.5.3	INTEGER	read-write	It is service level value, regular or priority, of a SU. The AP will poll priority user more often, thus better network latency as the result. As the network latency varies based on the number of subscriber units the AP serves, priority user is guaranteed that the latency is NOT greater than 100ms regardless of the size of the network.
INT suAddSUtoSU	1.3.6.1.4.1.5454.1.10.3.5.4	INTEGER	read-write	It is peer-to-peer group this SU belongs to. With the SU to SU switch is turned on, SUs in the same peer-to-peer group can communicate to each other via the AP. There are totally 15 groups available. Note that the SU shall be set to priority user for this feature to improve latency.
INT suAssociation	1.3.6.1.4.1.5454.1.10.3.6.1.13	INTEGER	read-only	Subscriber unit association status.
OCT suChecksum	1.3.6.1.4.1.5454.1.10.3.6.1.12	OCTET STRING	read-only	Subscriber unit firmware checksum.
INT suCIR	1.3.6.1.4.1.5454.1.10.3.6.1.5	INTEGER	read-only	It is the Committed Information Rate (in Kbps) the AP allocates to SU.
sudb	1.3.6.1.4.1.5454.1.10.3.5
INT suDelete	1.3.6.1.4.1.5454.1.10.3.5.8	INTEGER	read-write	Delete a subscriber (specified in object suAddOrDeleteID) from the subscriber database.
INT suDIstance	1.3.6.1.4.1.5454.1.10.3.6.1.14	INTEGER	read-only	Distance of SU (in mile).
INT suEthRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.18	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on the Ethernet port over the period specified by suStatisticsSamplePeriod.
INT suEthTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.19	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on the Ethernet port over the period specified by suStatisticsSamplePeriod.
OCT suFPGAVer	1.3.6.1.4.1.5454.1.10.3.6.1.11	OCTET STRING	read-only	Subscriber unit FPGA firmware version.
STR suFWVer	1.3.6.1.4.1.5454.1.10.3.6.1.10	DisplayString	read-only	Subscriber unit main firmware version.
OCT suHWVer	1.3.6.1.4.1.5454.1.10.3.6.1.9	OCTET STRING	read-only	Subscriber unit Hardware Version.
INT suID	1.3.6.1.4.1.5454.1.10.3.6.1.1	INTEGER	read-only	Subscriber unit ID. Each subscriber in a sector shall have a unique ID.
suInfoEntry	1.3.6.1.4.1.5454.1.10.3.6.1		not-accessible	Information about a specific subscriber unit retrieved by its ID number.
suInfoTable	1.3.6.1.4.1.5454.1.10.3.6		not-accessible	A table that contains subscriber unit entities.
IP suIPAddr	1.3.6.1.4.1.5454.1.10.3.6.1.7	IpAddress	read-only	Subscriber unit IP Address.
NTF suLinkDown	1.3.6.1.4.1.5454.1.10.16.0.8			The SNMP trap that is generated when a specific SU Powered Off.
NTF suLinkUp	1.3.6.1.4.1.5454.1.10.16.0.7			The SNMP trap that is generated when a specific SU Associated.
OCT suMAC	1.3.6.1.4.1.5454.1.10.3.6.1.2	OCTET STRING	read-only	Subscriber unit MAC Address. Format: 00 01 DE xx xx xx.
INT suMIR	1.3.6.1.4.1.5454.1.10.3.6.1.6	INTEGER	read-only	It is the Maximum Information Rate (in Kbps) the AP allocates to SU.
INT suPolling	1.3.6.1.4.1.5454.1.10.3.6.1.3	INTEGER	read-only	It is service level value, regular or priority, of a SU. The AP will poll priority user more often, thus better network latency as the result. As the network latency varies based on the number of subscriber units the AP serves, priority user is guaranteed that the latency is NOT greater than 100ms regardless of the size of the network.
INT suPowerLevel	1.3.6.1.4.1.5454.1.10.3.6.1.24	INTEGER	read-write	It is a feature that is typically found in more elaborate mobile systems such as cellular CDMA networks. Using this feature, the SU has its RF power output adjusted until its signal strength received in the AP is roughly the same.
INT suPowerLvlAll	1.3.6.1.4.1.5454.1.10.3.2	INTEGER	read-write	It is a feature that is typically found in more elaborate mobile systems such as cellular CDMA networks. Using this feature, all SUs have their RF power output adjusted until the signal strength for each SU as received in the AP is roughly the same.
INT suReboot	1.3.6.1.4.1.5454.1.10.3.6.1.26	INTEGER	read-write	AP issues reboot command to a specific subscriber unit.
INT suRebootAll	1.3.6.1.4.1.5454.1.10.3.4	INTEGER	read-write	AP broadcasts reboot command to all subscriber units.
STR suRemarks	1.3.6.1.4.1.5454.1.10.3.6.1.8	DisplayString	read-only	Subscriber unit Remark.
CTR suRfInOctets	1.3.6.1.4.1.5454.1.10.3.6.1.22	Counter	read-only	Number of payload octets received on the RF port.
CTR suRfOutOctets	1.3.6.1.4.1.5454.1.10.3.6.1.23	Counter	read-only	Number of payload octets transmitted on the RF port.
INT suRfRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.20	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on the RF port over the period specified by suStatisticsSamplePeriod.
INT suRfTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.21	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on the RF port over the period specified by suStatisticsSamplePeriod.
INT suRSSIFromAP	1.3.6.1.4.1.5454.1.10.3.6.1.16	INTEGER	read-only	Subscriber unit RSSI from AP (in dBm).
INT suRSSIFromSU	1.3.6.1.4.1.5454.1.10.3.6.1.15	INTEGER	read-only	Subscriber unit RSSI from SU (in dBm).
INT suStatisticsSamplePeriod	1.3.6.1.4.1.5454.1.10.3.3	INTEGER	read-write	A period (in minute) AP requests update on SU Info Table from all associated SUs.
INT suSUCount	1.3.6.1.4.1.5454.1.10.3.1	INTEGER	read-only	Number of subscriber units in the subscriber database.
INT suSUtoSU	1.3.6.1.4.1.5454.1.10.3.6.1.4	INTEGER	read-only	It is peer-to-peer group this SU belongs to. With the SU to SU switch is turned on, SUs in the same peer-to-peer group can communicate to each other via the AP. There are totally 15 groups available. Note that the SU shall be set to priority user for this feature to improve latency.
INT suTemperature	1.3.6.1.4.1.5454.1.10.3.6.1.25	INTEGER	read-only	Subscriber Unit temperature reading value (in Celsius).
INT suTxPower	1.3.6.1.4.1.5454.1.10.3.6.1.17	INTEGER	read-only	Subscriber unit Tx Power Level (in dBm).
tbw	1.3.6.1.4.1.5454.1
trango	1.3.6.1.4.1.5454
trapconfig	1.3.6.1.4.1.5454.1.10.4

OID symbolic	OID numeric	Type	Access	Description
trango	1.3.6.1.4.1.5454
tbw	1.3.6.1.4.1.5454.1
m5800sap	1.3.6.1.4.1.5454.1.10
apsystem	1.3.6.1.4.1.5454.1.10.1
apversion	1.3.6.1.4.1.5454.1.10.1.1
OCT apsysHW	1.3.6.1.4.1.5454.1.10.1.1.1	OCTET STRING	read-only	Hardware version.
STR apsysFW	1.3.6.1.4.1.5454.1.10.1.1.2	DisplayString	read-only	Main firmware version. Format: HD.
OCT apsysFPGA	1.3.6.1.4.1.5454.1.10.1.1.3	OCTET STRING	read-only	FPGA firmware version.
OCT apsysChecksum	1.3.6.1.4.1.5454.1.10.1.1.4	OCTET STRING	read-only	AP firmware checksum.
OCT apsysDeviceId	1.3.6.1.4.1.5454.1.10.1.2	OCTET STRING	read-only	MAC address.
INT apsysBaseId	1.3.6.1.4.1.5454.1.10.1.3	INTEGER	read-write	Cluster that the AP belongs to. All APs and SUs in the same cluster shall have the same Base ID.
INT apsysAPId	1.3.6.1.4.1.5454.1.10.1.4	INTEGER	read-write	AP ID. Each AP in a cluster shall have unique AP ID.
INT apsysDefOpMode	1.3.6.1.4.1.5454.1.10.1.5	INTEGER	read-write	The operation mode (ap or off) the radio is on after reboot/power cycle.
INT apsysCurOpMode	1.3.6.1.4.1.5454.1.10.1.6	INTEGER	read-only	Radio's current operation mode.
INT apsysActivateOpmode	1.3.6.1.4.1.5454.1.10.1.7	INTEGER	read-write	Engage AP unit to ap operation mode.
IP apsysIPAddr	1.3.6.1.4.1.5454.1.10.1.8	IpAddress	read-write	IP address.
IP apsysSubnet	1.3.6.1.4.1.5454.1.10.1.9	IpAddress	read-write	Subnet mask.
IP apsysDefaultGateway	1.3.6.1.4.1.5454.1.10.1.10	IpAddress	read-write	Default gateway.
STR apsysReadCommStr	1.3.6.1.4.1.5454.1.10.1.11	DisplayString	read-write	SNMP agent read community string. It is used for authentication purpose.
STR apsysWriteCommStr	1.3.6.1.4.1.5454.1.10.1.12	DisplayString	read-write	SNMP agent write community string. It is used for authentication purpose.
apswitches	1.3.6.1.4.1.5454.1.10.1.13
INT apsysBlockBroadcastMulticast	1.3.6.1.4.1.5454.1.10.1.13.1	INTEGER	read-write	This switch enables or disables the blocking of Ethernet control packet except ICMP and ARP to reduce the amount of uneccessary overhead introduced to the wireless link.
INT apsysSUtoSU	1.3.6.1.4.1.5454.1.10.1.13.2	INTEGER	read-write	This switch enables or disables the peer-to-peer feature among SUs through the AP. Before this switch is turned on, all SUs that want to communicate with each other have to be assigned to the same group.
INT apsysTFTPD	1.3.6.1.4.1.5454.1.10.1.13.4	INTEGER	read-write	This switch enables or disables the TFTP operation. When it is turned on, then the AP will be ready for code download.
INT apsysHTTPD	1.3.6.1.4.1.5454.1.10.1.13.5	INTEGER	read-write	When it is turned on, then the AP is accessible for configuring via web browser (e.g. IE or Nescape).
INT apsysMIRThreshold	1.3.6.1.4.1.5454.1.10.1.14	INTEGER	read-write	Maximum Information Rate (in Kbps), the AP allows the network to utilize before enforcing CIR on each subscriber.
aptraffic	1.3.6.1.4.1.5454.1.10.1.15
INT apsysEthRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.1	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on Ethernet port over the last 60 seconds.
INT apsysEthTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.2	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on Ethernet port over the last 60 seconds.
INT apsysRfRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.3	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on RF port over the last 60 seconds.
INT apsysRfTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.4	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on RF port over the last 60 seconds.
CTR apsysEthInOctets	1.3.6.1.4.1.5454.1.10.1.15.5	Counter	read-only	Number of payload octets received on Ethernet port.
CTR apsysEthOutOctets	1.3.6.1.4.1.5454.1.10.1.15.6	Counter	read-only	Number of payload octets transmitted on Ethernet port.
CTR apsysRfInOctets	1.3.6.1.4.1.5454.1.10.1.15.7	Counter	read-only	Number of octets of SUs payload received from RF port.
CTR apsysRfOutOctets	1.3.6.1.4.1.5454.1.10.1.15.8	Counter	read-only	Number of octets of SUs payload transmitted to RF port.
INT apsysTemperature	1.3.6.1.4.1.5454.1.10.1.16	INTEGER	read-only	Current AP temperature value (in Celsius).
INT apsysUpdateFlashAndActivate	1.3.6.1.4.1.5454.1.10.1.17	INTEGER	read-write	Save system setting values to Flash and activate the settings.
INT apsysReboot	1.3.6.1.4.1.5454.1.10.1.18	INTEGER	read-write	Reboot the radio.
aprf	1.3.6.1.4.1.5454.1.10.2
INT aprfActiveChannel	1.3.6.1.4.1.5454.1.10.2.1	INTEGER	read-write	It specifies the current channel number the radio operates on.
STR aprfActivePolarization	1.3.6.1.4.1.5454.1.10.2.2	DisplayString	read-write	It specifies the current polarization the radio operates on.
aprftable	1.3.6.1.4.1.5454.1.10.2.3
INT aprfChannel1	1.3.6.1.4.1.5454.1.10.2.3.1	INTEGER	read-write	RF channel 1 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel2	1.3.6.1.4.1.5454.1.10.2.3.2	INTEGER	read-write	RF channel 2 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel3	1.3.6.1.4.1.5454.1.10.2.3.3	INTEGER	read-write	RF channel 3 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel4	1.3.6.1.4.1.5454.1.10.2.3.4	INTEGER	read-write	RF channel 4 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel5	1.3.6.1.4.1.5454.1.10.2.3.5	INTEGER	read-write	RF channel 5 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel6	1.3.6.1.4.1.5454.1.10.2.3.6	INTEGER	read-write	RF channel 6 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel7	1.3.6.1.4.1.5454.1.10.2.3.7	INTEGER	read-write	RF channel 7 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel8	1.3.6.1.4.1.5454.1.10.2.3.8	INTEGER	read-write	RF channel 8 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel9	1.3.6.1.4.1.5454.1.10.2.3.9	INTEGER	read-write	RF channel 9 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel10	1.3.6.1.4.1.5454.1.10.2.3.10	INTEGER	read-write	RF channel 10 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel11	1.3.6.1.4.1.5454.1.10.2.3.11	INTEGER	read-write	RF channel 11 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel12	1.3.6.1.4.1.5454.1.10.2.3.12	INTEGER	read-write	RF channel 12 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel13	1.3.6.1.4.1.5454.1.10.2.3.13	INTEGER	read-write	RF channel 13 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel14	1.3.6.1.4.1.5454.1.10.2.3.14	INTEGER	read-write	RF channel 14 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel15	1.3.6.1.4.1.5454.1.10.2.3.15	INTEGER	read-write	RF channel 15 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel16	1.3.6.1.4.1.5454.1.10.2.3.16	INTEGER	read-write	RF channel 16 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel17	1.3.6.1.4.1.5454.1.10.2.3.17	INTEGER	read-write	RF channel 17 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel18	1.3.6.1.4.1.5454.1.10.2.3.18	INTEGER	read-write	RF channel 18 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel19	1.3.6.1.4.1.5454.1.10.2.3.19	INTEGER	read-write	RF channel 19 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel20	1.3.6.1.4.1.5454.1.10.2.3.20	INTEGER	read-write	RF channel 20 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel21	1.3.6.1.4.1.5454.1.10.2.3.21	INTEGER	read-write	RF channel 21 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel22	1.3.6.1.4.1.5454.1.10.2.3.22	INTEGER	read-write	RF channel 22 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel23	1.3.6.1.4.1.5454.1.10.2.3.23	INTEGER	read-write	RF channel 23 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel24	1.3.6.1.4.1.5454.1.10.2.3.24	INTEGER	read-write	RF channel 24 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel25	1.3.6.1.4.1.5454.1.10.2.3.25	INTEGER	read-write	RF channel 25 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel26	1.3.6.1.4.1.5454.1.10.2.3.26	INTEGER	read-write	RF channel 26 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel27	1.3.6.1.4.1.5454.1.10.2.3.27	INTEGER	read-write	RF channel 27 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel28	1.3.6.1.4.1.5454.1.10.2.3.28	INTEGER	read-write	RF channel 28 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel29	1.3.6.1.4.1.5454.1.10.2.3.29	INTEGER	read-write	RF channel 29 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel30	1.3.6.1.4.1.5454.1.10.2.3.30	INTEGER	read-write	RF channel 30 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
apism	1.3.6.1.4.1.5454.1.10.2.4
INT aprfismTxPowerMax	1.3.6.1.4.1.5454.1.10.2.4.1	INTEGER	read-only	The maximum ISM Tx power value can be set (in dBm).
INT aprfismTxPowerMin	1.3.6.1.4.1.5454.1.10.2.4.2	INTEGER	read-only	The minimum ISM Tx power value can be set (in dBm).
INT aprfismTxPower	1.3.6.1.4.1.5454.1.10.2.4.3	INTEGER	read-write	ISM RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters aprfismTxPowerMax and aprfismTxPowerMin for power setting range.
INT aprfismServiceRadius	1.3.6.1.4.1.5454.1.10.2.4.4	INTEGER	read-write	ISM RF service radius (in mile). It specifies the distance of the furthest SU the AP will serve. Based on this information, the AP will determine the maximum wait time for a SU to response to a poll before it starts to poll the next one.
INT aprfismRxThreshold	1.3.6.1.4.1.5454.1.10.2.4.5	INTEGER	read-write	ISM RF rx threshold (in dBm). It specifies the receiver sensitivity of the AP. By default, the radio's sensitivity is -82dBm. The higher the threshold is, the less sensitive the radio will be. In M5800S, the value -90 represents the rfrxthreshold is disabled.
INT aprfismTargetRSSI	1.3.6.1.4.1.5454.1.10.2.4.6	INTEGER	read-write	ISM RF target RSSI (in dBm). It specifies the target RSSI from all SUs to the AP. Based on this parameter, the AP can power level each SU so that it receives same level of signal strength from all SUs, regardless far or near. Note that when you set the Target RSSI from SU, you need to consider AP's RF Rx Threshold value. The Target RSSI from SU must be 5dB higher than the RF Rx Threshold. When the RF Rx Threshold is disabled, the setting of the Target RSSI from SU shall be no less than -75dBm.
apunii	1.3.6.1.4.1.5454.1.10.2.5
INT aprfuniiTxPowerMax	1.3.6.1.4.1.5454.1.10.2.5.1	INTEGER	read-only	This object is only applicable to M5830S radio. The maximum UNII Tx power value can be set (in dBm).
INT aprfuniiTxPowerMin	1.3.6.1.4.1.5454.1.10.2.5.2	INTEGER	read-only	This object is only applicable to M5830S radio. The minimum UNII Tx power value can be set (in dBm).
INT aprfuniiTxPower	1.3.6.1.4.1.5454.1.10.2.5.3	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters aprfuniiTxPowerMax and aprfuniiTxPowerMin for power setting range.
INT aprfuniiServiceRadius	1.3.6.1.4.1.5454.1.10.2.5.4	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF service radius (in mile). It specifies the distance of the furthest SU the AP will serve. Based on this information, the AP will determine the maximum wait time for a SU to response to a poll before it starts to poll the next one.
INT aprfuniiRxThreshold	1.3.6.1.4.1.5454.1.10.2.5.5	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF rx threshold (in dBm). It specifies the receiver sensitivity of the AP.
INT aprfuniiTargetRSSI	1.3.6.1.4.1.5454.1.10.2.5.6	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF target RSSI (in dBm). It specifies the target RSSI from all SUs to the AP. Based on this parameter, the AP can power level each SU so that it receives same level of signal strength from all SUs, regardless far or near. Note that when you set the Target RSSI from SU, you need to consider AP's RF Rx Threshold value. The Target RSSI from SU must be 5dB higher than the RF Rx Threshold.
su	1.3.6.1.4.1.5454.1.10.3
INT suSUCount	1.3.6.1.4.1.5454.1.10.3.1	INTEGER	read-only	Number of subscriber units in the subscriber database.
INT suPowerLvlAll	1.3.6.1.4.1.5454.1.10.3.2	INTEGER	read-write	It is a feature that is typically found in more elaborate mobile systems such as cellular CDMA networks. Using this feature, all SUs have their RF power output adjusted until the signal strength for each SU as received in the AP is roughly the same.
INT suStatisticsSamplePeriod	1.3.6.1.4.1.5454.1.10.3.3	INTEGER	read-write	A period (in minute) AP requests update on SU Info Table from all associated SUs.
INT suRebootAll	1.3.6.1.4.1.5454.1.10.3.4	INTEGER	read-write	AP broadcasts reboot command to all subscriber units.
sudb	1.3.6.1.4.1.5454.1.10.3.5
INT suAddOrDeleteID	1.3.6.1.4.1.5454.1.10.3.5.1	INTEGER	read-write	Subscriber unit ID (1..8190). Each subscriber in a sector shall have a unique ID.
OCT suAddMAC	1.3.6.1.4.1.5454.1.10.3.5.2	OCTET STRING	read-write	It is the MAC address of the subscriber unit, which can be found on the back of the SU.
INT suAddPolling	1.3.6.1.4.1.5454.1.10.3.5.3	INTEGER	read-write	It is service level value, regular or priority, of a SU. The AP will poll priority user more often, thus better network latency as the result. As the network latency varies based on the number of subscriber units the AP serves, priority user is guaranteed that the latency is NOT greater than 100ms regardless of the size of the network.
INT suAddSUtoSU	1.3.6.1.4.1.5454.1.10.3.5.4	INTEGER	read-write	It is peer-to-peer group this SU belongs to. With the SU to SU switch is turned on, SUs in the same peer-to-peer group can communicate to each other via the AP. There are totally 15 groups available. Note that the SU shall be set to priority user for this feature to improve latency.
INT suAddCIR	1.3.6.1.4.1.5454.1.10.3.5.5	INTEGER	read-write	It is the Committed Information Rate (in Kbps) the AP allocates to SU.
INT suAddMIR	1.3.6.1.4.1.5454.1.10.3.5.6	INTEGER	read-write	It is the Maximum Information Rate (in Kbps) the AP allocates to SU.
INT suAdd	1.3.6.1.4.1.5454.1.10.3.5.7	INTEGER	read-write	Add a subscriber (specified in object suAddOrDeleteID) to the subscriber database.
INT suDelete	1.3.6.1.4.1.5454.1.10.3.5.8	INTEGER	read-write	Delete a subscriber (specified in object suAddOrDeleteID) from the subscriber database.
suInfoTable	1.3.6.1.4.1.5454.1.10.3.6		not-accessible	A table that contains subscriber unit entities.
suInfoEntry	1.3.6.1.4.1.5454.1.10.3.6.1		not-accessible	Information about a specific subscriber unit retrieved by its ID number.
INT suID	1.3.6.1.4.1.5454.1.10.3.6.1.1	INTEGER	read-only	Subscriber unit ID. Each subscriber in a sector shall have a unique ID.
OCT suMAC	1.3.6.1.4.1.5454.1.10.3.6.1.2	OCTET STRING	read-only	Subscriber unit MAC Address. Format: 00 01 DE xx xx xx.
INT suPolling	1.3.6.1.4.1.5454.1.10.3.6.1.3	INTEGER	read-only	It is service level value, regular or priority, of a SU. The AP will poll priority user more often, thus better network latency as the result. As the network latency varies based on the number of subscriber units the AP serves, priority user is guaranteed that the latency is NOT greater than 100ms regardless of the size of the network.
INT suSUtoSU	1.3.6.1.4.1.5454.1.10.3.6.1.4	INTEGER	read-only	It is peer-to-peer group this SU belongs to. With the SU to SU switch is turned on, SUs in the same peer-to-peer group can communicate to each other via the AP. There are totally 15 groups available. Note that the SU shall be set to priority user for this feature to improve latency.
INT suCIR	1.3.6.1.4.1.5454.1.10.3.6.1.5	INTEGER	read-only	It is the Committed Information Rate (in Kbps) the AP allocates to SU.
INT suMIR	1.3.6.1.4.1.5454.1.10.3.6.1.6	INTEGER	read-only	It is the Maximum Information Rate (in Kbps) the AP allocates to SU.
IP suIPAddr	1.3.6.1.4.1.5454.1.10.3.6.1.7	IpAddress	read-only	Subscriber unit IP Address.
STR suRemarks	1.3.6.1.4.1.5454.1.10.3.6.1.8	DisplayString	read-only	Subscriber unit Remark.
OCT suHWVer	1.3.6.1.4.1.5454.1.10.3.6.1.9	OCTET STRING	read-only	Subscriber unit Hardware Version.
STR suFWVer	1.3.6.1.4.1.5454.1.10.3.6.1.10	DisplayString	read-only	Subscriber unit main firmware version.
OCT suFPGAVer	1.3.6.1.4.1.5454.1.10.3.6.1.11	OCTET STRING	read-only	Subscriber unit FPGA firmware version.
OCT suChecksum	1.3.6.1.4.1.5454.1.10.3.6.1.12	OCTET STRING	read-only	Subscriber unit firmware checksum.
INT suAssociation	1.3.6.1.4.1.5454.1.10.3.6.1.13	INTEGER	read-only	Subscriber unit association status.
INT suDIstance	1.3.6.1.4.1.5454.1.10.3.6.1.14	INTEGER	read-only	Distance of SU (in mile).
INT suRSSIFromSU	1.3.6.1.4.1.5454.1.10.3.6.1.15	INTEGER	read-only	Subscriber unit RSSI from SU (in dBm).
INT suRSSIFromAP	1.3.6.1.4.1.5454.1.10.3.6.1.16	INTEGER	read-only	Subscriber unit RSSI from AP (in dBm).
INT suTxPower	1.3.6.1.4.1.5454.1.10.3.6.1.17	INTEGER	read-only	Subscriber unit Tx Power Level (in dBm).
INT suEthRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.18	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on the Ethernet port over the period specified by suStatisticsSamplePeriod.
INT suEthTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.19	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on the Ethernet port over the period specified by suStatisticsSamplePeriod.
INT suRfRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.20	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on the RF port over the period specified by suStatisticsSamplePeriod.
INT suRfTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.21	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on the RF port over the period specified by suStatisticsSamplePeriod.
CTR suRfInOctets	1.3.6.1.4.1.5454.1.10.3.6.1.22	Counter	read-only	Number of payload octets received on the RF port.
CTR suRfOutOctets	1.3.6.1.4.1.5454.1.10.3.6.1.23	Counter	read-only	Number of payload octets transmitted on the RF port.
INT suPowerLevel	1.3.6.1.4.1.5454.1.10.3.6.1.24	INTEGER	read-write	It is a feature that is typically found in more elaborate mobile systems such as cellular CDMA networks. Using this feature, the SU has its RF power output adjusted until its signal strength received in the AP is roughly the same.
INT suTemperature	1.3.6.1.4.1.5454.1.10.3.6.1.25	INTEGER	read-only	Subscriber Unit temperature reading value (in Celsius).
INT suReboot	1.3.6.1.4.1.5454.1.10.3.6.1.26	INTEGER	read-write	AP issues reboot command to a specific subscriber unit.
trapconfig	1.3.6.1.4.1.5454.1.10.4
INT aptrpCount	1.3.6.1.4.1.5454.1.10.4.1	INTEGER	read-only	Types of trap.
IP aptrpDest1IPAddress	1.3.6.1.4.1.5454.1.10.4.2	IpAddress	read-write	Trap destination 1 IP address.
IP aptrpDest2IPAddress	1.3.6.1.4.1.5454.1.10.4.3	IpAddress	read-write	Trap destination 2 IP address.
aptrpTable	1.3.6.1.4.1.5454.1.10.4.4		not-accessible	A table that contains information of Trango trap events .
aptrpEntry	1.3.6.1.4.1.5454.1.10.4.4.1		not-accessible	Information about a specific Trango trap event.
INT aptrpIndex	1.3.6.1.4.1.5454.1.10.4.4.1.1	INTEGER	read-only	Trap index.
INT aptrpID	1.3.6.1.4.1.5454.1.10.4.4.1.2	INTEGER	read-only	Specific trap ID.
STR aptrpCommStr	1.3.6.1.4.1.5454.1.10.4.4.1.3	DisplayString	read-write	Specific trap community string.
INT aptrpEnable	1.3.6.1.4.1.5454.1.10.4.4.1.4	INTEGER	read-write	Enable a specific Trango trap event or not.
mibinfo	1.3.6.1.4.1.5454.1.10.5
STR mibinfoVersion	1.3.6.1.4.1.5454.1.10.5.1	DisplayString	read-only	Trango MIB Version.
m5800straps	1.3.6.1.4.1.5454.1.10.16
NTF suLinkUp	1.3.6.1.4.1.5454.1.10.16.0.7			The SNMP trap that is generated when a specific SU Associated.
NTF suLinkDown	1.3.6.1.4.1.5454.1.10.16.0.8			The SNMP trap that is generated when a specific SU Powered Off.
NTF apOpModeFailure	1.3.6.1.4.1.5454.1.10.16.0.9			The SNMP trap that is generated when a specific AP not being in ap mode during boot up sequence.

Counter (6)
CTR apsysEthInOctets	1.3.6.1.4.1.5454.1.10.1.15.5	Counter	read-only	Number of payload octets received on Ethernet port.
CTR apsysEthOutOctets	1.3.6.1.4.1.5454.1.10.1.15.6	Counter	read-only	Number of payload octets transmitted on Ethernet port.
CTR apsysRfInOctets	1.3.6.1.4.1.5454.1.10.1.15.7	Counter	read-only	Number of octets of SUs payload received from RF port.
CTR apsysRfOutOctets	1.3.6.1.4.1.5454.1.10.1.15.8	Counter	read-only	Number of octets of SUs payload transmitted to RF port.
CTR suRfInOctets	1.3.6.1.4.1.5454.1.10.3.6.1.22	Counter	read-only	Number of payload octets received on the RF port.
CTR suRfOutOctets	1.3.6.1.4.1.5454.1.10.3.6.1.23	Counter	read-only	Number of payload octets transmitted on the RF port.
DisplayString (8)
STR aprfActivePolarization	1.3.6.1.4.1.5454.1.10.2.2	DisplayString	read-write	It specifies the current polarization the radio operates on.
STR apsysFW	1.3.6.1.4.1.5454.1.10.1.1.2	DisplayString	read-only	Main firmware version. Format: HD.
STR apsysReadCommStr	1.3.6.1.4.1.5454.1.10.1.11	DisplayString	read-write	SNMP agent read community string. It is used for authentication purpose.
STR apsysWriteCommStr	1.3.6.1.4.1.5454.1.10.1.12	DisplayString	read-write	SNMP agent write community string. It is used for authentication purpose.
STR aptrpCommStr	1.3.6.1.4.1.5454.1.10.4.4.1.3	DisplayString	read-write	Specific trap community string.
STR mibinfoVersion	1.3.6.1.4.1.5454.1.10.5.1	DisplayString	read-only	Trango MIB Version.
STR suFWVer	1.3.6.1.4.1.5454.1.10.3.6.1.10	DisplayString	read-only	Subscriber unit main firmware version.
STR suRemarks	1.3.6.1.4.1.5454.1.10.3.6.1.8	DisplayString	read-only	Subscriber unit Remark.
INTEGER (92)
INT aprfActiveChannel	1.3.6.1.4.1.5454.1.10.2.1	INTEGER	read-write	It specifies the current channel number the radio operates on.
INT aprfChannel1	1.3.6.1.4.1.5454.1.10.2.3.1	INTEGER	read-write	RF channel 1 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel10	1.3.6.1.4.1.5454.1.10.2.3.10	INTEGER	read-write	RF channel 10 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel11	1.3.6.1.4.1.5454.1.10.2.3.11	INTEGER	read-write	RF channel 11 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel12	1.3.6.1.4.1.5454.1.10.2.3.12	INTEGER	read-write	RF channel 12 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel13	1.3.6.1.4.1.5454.1.10.2.3.13	INTEGER	read-write	RF channel 13 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel14	1.3.6.1.4.1.5454.1.10.2.3.14	INTEGER	read-write	RF channel 14 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel15	1.3.6.1.4.1.5454.1.10.2.3.15	INTEGER	read-write	RF channel 15 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel16	1.3.6.1.4.1.5454.1.10.2.3.16	INTEGER	read-write	RF channel 16 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel17	1.3.6.1.4.1.5454.1.10.2.3.17	INTEGER	read-write	RF channel 17 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel18	1.3.6.1.4.1.5454.1.10.2.3.18	INTEGER	read-write	RF channel 18 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel19	1.3.6.1.4.1.5454.1.10.2.3.19	INTEGER	read-write	RF channel 19 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel2	1.3.6.1.4.1.5454.1.10.2.3.2	INTEGER	read-write	RF channel 2 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel20	1.3.6.1.4.1.5454.1.10.2.3.20	INTEGER	read-write	RF channel 20 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel21	1.3.6.1.4.1.5454.1.10.2.3.21	INTEGER	read-write	RF channel 21 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel22	1.3.6.1.4.1.5454.1.10.2.3.22	INTEGER	read-write	RF channel 22 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel23	1.3.6.1.4.1.5454.1.10.2.3.23	INTEGER	read-write	RF channel 23 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel24	1.3.6.1.4.1.5454.1.10.2.3.24	INTEGER	read-write	RF channel 24 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel25	1.3.6.1.4.1.5454.1.10.2.3.25	INTEGER	read-write	RF channel 25 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel26	1.3.6.1.4.1.5454.1.10.2.3.26	INTEGER	read-write	RF channel 26 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel27	1.3.6.1.4.1.5454.1.10.2.3.27	INTEGER	read-write	RF channel 27 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel28	1.3.6.1.4.1.5454.1.10.2.3.28	INTEGER	read-write	RF channel 28 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel29	1.3.6.1.4.1.5454.1.10.2.3.29	INTEGER	read-write	RF channel 29 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel3	1.3.6.1.4.1.5454.1.10.2.3.3	INTEGER	read-write	RF channel 3 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel30	1.3.6.1.4.1.5454.1.10.2.3.30	INTEGER	read-write	RF channel 30 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel4	1.3.6.1.4.1.5454.1.10.2.3.4	INTEGER	read-write	RF channel 4 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel5	1.3.6.1.4.1.5454.1.10.2.3.5	INTEGER	read-write	RF channel 5 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel6	1.3.6.1.4.1.5454.1.10.2.3.6	INTEGER	read-write	RF channel 6 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel7	1.3.6.1.4.1.5454.1.10.2.3.7	INTEGER	read-write	RF channel 7 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel8	1.3.6.1.4.1.5454.1.10.2.3.8	INTEGER	read-write	RF channel 8 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfChannel9	1.3.6.1.4.1.5454.1.10.2.3.9	INTEGER	read-write	RF channel 9 frequency (in MHz). It allows you to create your own channel instead of the manufacturing defaults in the AP. Keep in mind that channel width is 20MHz, and the frequency specified here is the center frequency. Frequency (5260MHz - 5340MHz) is only applicable to M5830S radio.
INT aprfismRxThreshold	1.3.6.1.4.1.5454.1.10.2.4.5	INTEGER	read-write	ISM RF rx threshold (in dBm). It specifies the receiver sensitivity of the AP. By default, the radio's sensitivity is -82dBm. The higher the threshold is, the less sensitive the radio will be. In M5800S, the value -90 represents the rfrxthreshold is disabled.
INT aprfismServiceRadius	1.3.6.1.4.1.5454.1.10.2.4.4	INTEGER	read-write	ISM RF service radius (in mile). It specifies the distance of the furthest SU the AP will serve. Based on this information, the AP will determine the maximum wait time for a SU to response to a poll before it starts to poll the next one.
INT aprfismTargetRSSI	1.3.6.1.4.1.5454.1.10.2.4.6	INTEGER	read-write	ISM RF target RSSI (in dBm). It specifies the target RSSI from all SUs to the AP. Based on this parameter, the AP can power level each SU so that it receives same level of signal strength from all SUs, regardless far or near. Note that when you set the Target RSSI from SU, you need to consider AP's RF Rx Threshold value. The Target RSSI from SU must be 5dB higher than the RF Rx Threshold. When the RF Rx Threshold is disabled, the setting of the Target RSSI from SU shall be no less than -75dBm.
INT aprfismTxPower	1.3.6.1.4.1.5454.1.10.2.4.3	INTEGER	read-write	ISM RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters aprfismTxPowerMax and aprfismTxPowerMin for power setting range.
INT aprfismTxPowerMax	1.3.6.1.4.1.5454.1.10.2.4.1	INTEGER	read-only	The maximum ISM Tx power value can be set (in dBm).
INT aprfismTxPowerMin	1.3.6.1.4.1.5454.1.10.2.4.2	INTEGER	read-only	The minimum ISM Tx power value can be set (in dBm).
INT aprfuniiRxThreshold	1.3.6.1.4.1.5454.1.10.2.5.5	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF rx threshold (in dBm). It specifies the receiver sensitivity of the AP.
INT aprfuniiServiceRadius	1.3.6.1.4.1.5454.1.10.2.5.4	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF service radius (in mile). It specifies the distance of the furthest SU the AP will serve. Based on this information, the AP will determine the maximum wait time for a SU to response to a poll before it starts to poll the next one.
INT aprfuniiTargetRSSI	1.3.6.1.4.1.5454.1.10.2.5.6	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF target RSSI (in dBm). It specifies the target RSSI from all SUs to the AP. Based on this parameter, the AP can power level each SU so that it receives same level of signal strength from all SUs, regardless far or near. Note that when you set the Target RSSI from SU, you need to consider AP's RF Rx Threshold value. The Target RSSI from SU must be 5dB higher than the RF Rx Threshold.
INT aprfuniiTxPower	1.3.6.1.4.1.5454.1.10.2.5.3	INTEGER	read-write	This object is only applicable to M5830S radio. UNII RF tx power (in dBm). It specifies the power output of the radio, excluding the antenna gain. Check parameters aprfuniiTxPowerMax and aprfuniiTxPowerMin for power setting range.
INT aprfuniiTxPowerMax	1.3.6.1.4.1.5454.1.10.2.5.1	INTEGER	read-only	This object is only applicable to M5830S radio. The maximum UNII Tx power value can be set (in dBm).
INT aprfuniiTxPowerMin	1.3.6.1.4.1.5454.1.10.2.5.2	INTEGER	read-only	This object is only applicable to M5830S radio. The minimum UNII Tx power value can be set (in dBm).
INT apsysActivateOpmode	1.3.6.1.4.1.5454.1.10.1.7	INTEGER	read-write	Engage AP unit to ap operation mode.
INT apsysAPId	1.3.6.1.4.1.5454.1.10.1.4	INTEGER	read-write	AP ID. Each AP in a cluster shall have unique AP ID.
INT apsysBaseId	1.3.6.1.4.1.5454.1.10.1.3	INTEGER	read-write	Cluster that the AP belongs to. All APs and SUs in the same cluster shall have the same Base ID.
INT apsysBlockBroadcastMulticast	1.3.6.1.4.1.5454.1.10.1.13.1	INTEGER	read-write	This switch enables or disables the blocking of Ethernet control packet except ICMP and ARP to reduce the amount of uneccessary overhead introduced to the wireless link.
INT apsysCurOpMode	1.3.6.1.4.1.5454.1.10.1.6	INTEGER	read-only	Radio's current operation mode.
INT apsysDefOpMode	1.3.6.1.4.1.5454.1.10.1.5	INTEGER	read-write	The operation mode (ap or off) the radio is on after reboot/power cycle.
INT apsysEthRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.1	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on Ethernet port over the last 60 seconds.
INT apsysEthTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.2	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on Ethernet port over the last 60 seconds.
INT apsysHTTPD	1.3.6.1.4.1.5454.1.10.1.13.5	INTEGER	read-write	When it is turned on, then the AP is accessible for configuring via web browser (e.g. IE or Nescape).
INT apsysMIRThreshold	1.3.6.1.4.1.5454.1.10.1.14	INTEGER	read-write	Maximum Information Rate (in Kbps), the AP allows the network to utilize before enforcing CIR on each subscriber.
INT apsysReboot	1.3.6.1.4.1.5454.1.10.1.18	INTEGER	read-write	Reboot the radio.
INT apsysRfRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.3	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on RF port over the last 60 seconds.
INT apsysRfTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.1.15.4	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on RF port over the last 60 seconds.
INT apsysSUtoSU	1.3.6.1.4.1.5454.1.10.1.13.2	INTEGER	read-write	This switch enables or disables the peer-to-peer feature among SUs through the AP. Before this switch is turned on, all SUs that want to communicate with each other have to be assigned to the same group.
INT apsysTemperature	1.3.6.1.4.1.5454.1.10.1.16	INTEGER	read-only	Current AP temperature value (in Celsius).
INT apsysTFTPD	1.3.6.1.4.1.5454.1.10.1.13.4	INTEGER	read-write	This switch enables or disables the TFTP operation. When it is turned on, then the AP will be ready for code download.
INT apsysUpdateFlashAndActivate	1.3.6.1.4.1.5454.1.10.1.17	INTEGER	read-write	Save system setting values to Flash and activate the settings.
INT aptrpCount	1.3.6.1.4.1.5454.1.10.4.1	INTEGER	read-only	Types of trap.
INT aptrpEnable	1.3.6.1.4.1.5454.1.10.4.4.1.4	INTEGER	read-write	Enable a specific Trango trap event or not.
INT aptrpID	1.3.6.1.4.1.5454.1.10.4.4.1.2	INTEGER	read-only	Specific trap ID.
INT aptrpIndex	1.3.6.1.4.1.5454.1.10.4.4.1.1	INTEGER	read-only	Trap index.
INT suAdd	1.3.6.1.4.1.5454.1.10.3.5.7	INTEGER	read-write	Add a subscriber (specified in object suAddOrDeleteID) to the subscriber database.
INT suAddCIR	1.3.6.1.4.1.5454.1.10.3.5.5	INTEGER	read-write	It is the Committed Information Rate (in Kbps) the AP allocates to SU.
INT suAddMIR	1.3.6.1.4.1.5454.1.10.3.5.6	INTEGER	read-write	It is the Maximum Information Rate (in Kbps) the AP allocates to SU.
INT suAddOrDeleteID	1.3.6.1.4.1.5454.1.10.3.5.1	INTEGER	read-write	Subscriber unit ID (1..8190). Each subscriber in a sector shall have a unique ID.
INT suAddPolling	1.3.6.1.4.1.5454.1.10.3.5.3	INTEGER	read-write	It is service level value, regular or priority, of a SU. The AP will poll priority user more often, thus better network latency as the result. As the network latency varies based on the number of subscriber units the AP serves, priority user is guaranteed that the latency is NOT greater than 100ms regardless of the size of the network.
INT suAddSUtoSU	1.3.6.1.4.1.5454.1.10.3.5.4	INTEGER	read-write	It is peer-to-peer group this SU belongs to. With the SU to SU switch is turned on, SUs in the same peer-to-peer group can communicate to each other via the AP. There are totally 15 groups available. Note that the SU shall be set to priority user for this feature to improve latency.
INT suAssociation	1.3.6.1.4.1.5454.1.10.3.6.1.13	INTEGER	read-only	Subscriber unit association status.
INT suCIR	1.3.6.1.4.1.5454.1.10.3.6.1.5	INTEGER	read-only	It is the Committed Information Rate (in Kbps) the AP allocates to SU.
INT suDelete	1.3.6.1.4.1.5454.1.10.3.5.8	INTEGER	read-write	Delete a subscriber (specified in object suAddOrDeleteID) from the subscriber database.
INT suDIstance	1.3.6.1.4.1.5454.1.10.3.6.1.14	INTEGER	read-only	Distance of SU (in mile).
INT suEthRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.18	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on the Ethernet port over the period specified by suStatisticsSamplePeriod.
INT suEthTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.19	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on the Ethernet port over the period specified by suStatisticsSamplePeriod.
INT suID	1.3.6.1.4.1.5454.1.10.3.6.1.1	INTEGER	read-only	Subscriber unit ID. Each subscriber in a sector shall have a unique ID.
INT suMIR	1.3.6.1.4.1.5454.1.10.3.6.1.6	INTEGER	read-only	It is the Maximum Information Rate (in Kbps) the AP allocates to SU.
INT suPolling	1.3.6.1.4.1.5454.1.10.3.6.1.3	INTEGER	read-only	It is service level value, regular or priority, of a SU. The AP will poll priority user more often, thus better network latency as the result. As the network latency varies based on the number of subscriber units the AP serves, priority user is guaranteed that the latency is NOT greater than 100ms regardless of the size of the network.
INT suPowerLevel	1.3.6.1.4.1.5454.1.10.3.6.1.24	INTEGER	read-write	It is a feature that is typically found in more elaborate mobile systems such as cellular CDMA networks. Using this feature, the SU has its RF power output adjusted until its signal strength received in the AP is roughly the same.
INT suPowerLvlAll	1.3.6.1.4.1.5454.1.10.3.2	INTEGER	read-write	It is a feature that is typically found in more elaborate mobile systems such as cellular CDMA networks. Using this feature, all SUs have their RF power output adjusted until the signal strength for each SU as received in the AP is roughly the same.
INT suReboot	1.3.6.1.4.1.5454.1.10.3.6.1.26	INTEGER	read-write	AP issues reboot command to a specific subscriber unit.
INT suRebootAll	1.3.6.1.4.1.5454.1.10.3.4	INTEGER	read-write	AP broadcasts reboot command to all subscriber units.
INT suRfRxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.20	INTEGER	read-only	Average payload data throughput (in Kbits/sec) received on the RF port over the period specified by suStatisticsSamplePeriod.
INT suRfTxAvgThroughputLog	1.3.6.1.4.1.5454.1.10.3.6.1.21	INTEGER	read-only	Average payload data throughput (in Kbits/sec) transmitted on the RF port over the period specified by suStatisticsSamplePeriod.
INT suRSSIFromAP	1.3.6.1.4.1.5454.1.10.3.6.1.16	INTEGER	read-only	Subscriber unit RSSI from AP (in dBm).
INT suRSSIFromSU	1.3.6.1.4.1.5454.1.10.3.6.1.15	INTEGER	read-only	Subscriber unit RSSI from SU (in dBm).
INT suStatisticsSamplePeriod	1.3.6.1.4.1.5454.1.10.3.3	INTEGER	read-write	A period (in minute) AP requests update on SU Info Table from all associated SUs.
INT suSUCount	1.3.6.1.4.1.5454.1.10.3.1	INTEGER	read-only	Number of subscriber units in the subscriber database.
INT suSUtoSU	1.3.6.1.4.1.5454.1.10.3.6.1.4	INTEGER	read-only	It is peer-to-peer group this SU belongs to. With the SU to SU switch is turned on, SUs in the same peer-to-peer group can communicate to each other via the AP. There are totally 15 groups available. Note that the SU shall be set to priority user for this feature to improve latency.
INT suTemperature	1.3.6.1.4.1.5454.1.10.3.6.1.25	INTEGER	read-only	Subscriber Unit temperature reading value (in Celsius).
INT suTxPower	1.3.6.1.4.1.5454.1.10.3.6.1.17	INTEGER	read-only	Subscriber unit Tx Power Level (in dBm).
IpAddress (6)
IP apsysDefaultGateway	1.3.6.1.4.1.5454.1.10.1.10	IpAddress	read-write	Default gateway.
IP apsysIPAddr	1.3.6.1.4.1.5454.1.10.1.8	IpAddress	read-write	IP address.
IP apsysSubnet	1.3.6.1.4.1.5454.1.10.1.9	IpAddress	read-write	Subnet mask.
IP aptrpDest1IPAddress	1.3.6.1.4.1.5454.1.10.4.2	IpAddress	read-write	Trap destination 1 IP address.
IP aptrpDest2IPAddress	1.3.6.1.4.1.5454.1.10.4.3	IpAddress	read-write	Trap destination 2 IP address.
IP suIPAddr	1.3.6.1.4.1.5454.1.10.3.6.1.7	IpAddress	read-only	Subscriber unit IP Address.
OCTET STRING (9)
OCT apsysChecksum	1.3.6.1.4.1.5454.1.10.1.1.4	OCTET STRING	read-only	AP firmware checksum.
OCT apsysDeviceId	1.3.6.1.4.1.5454.1.10.1.2	OCTET STRING	read-only	MAC address.
OCT apsysFPGA	1.3.6.1.4.1.5454.1.10.1.1.3	OCTET STRING	read-only	FPGA firmware version.
OCT apsysHW	1.3.6.1.4.1.5454.1.10.1.1.1	OCTET STRING	read-only	Hardware version.
OCT suAddMAC	1.3.6.1.4.1.5454.1.10.3.5.2	OCTET STRING	read-write	It is the MAC address of the subscriber unit, which can be found on the back of the SU.
OCT suChecksum	1.3.6.1.4.1.5454.1.10.3.6.1.12	OCTET STRING	read-only	Subscriber unit firmware checksum.
OCT suFPGAVer	1.3.6.1.4.1.5454.1.10.3.6.1.11	OCTET STRING	read-only	Subscriber unit FPGA firmware version.
OCT suHWVer	1.3.6.1.4.1.5454.1.10.3.6.1.9	OCTET STRING	read-only	Subscriber unit Hardware Version.
OCT suMAC	1.3.6.1.4.1.5454.1.10.3.6.1.2	OCTET STRING	read-only	Subscriber unit MAC Address. Format: 00 01 DE xx xx xx.
No type (23)
apism	1.3.6.1.4.1.5454.1.10.2.4
NTF apOpModeFailure	1.3.6.1.4.1.5454.1.10.16.0.9			The SNMP trap that is generated when a specific AP not being in ap mode during boot up sequence.
aprf	1.3.6.1.4.1.5454.1.10.2
aprftable	1.3.6.1.4.1.5454.1.10.2.3
apswitches	1.3.6.1.4.1.5454.1.10.1.13
apsystem	1.3.6.1.4.1.5454.1.10.1
aptraffic	1.3.6.1.4.1.5454.1.10.1.15
aptrpEntry	1.3.6.1.4.1.5454.1.10.4.4.1		not-accessible	Information about a specific Trango trap event.
aptrpTable	1.3.6.1.4.1.5454.1.10.4.4		not-accessible	A table that contains information of Trango trap events .
apunii	1.3.6.1.4.1.5454.1.10.2.5
apversion	1.3.6.1.4.1.5454.1.10.1.1
m5800sap	1.3.6.1.4.1.5454.1.10
m5800straps	1.3.6.1.4.1.5454.1.10.16
mibinfo	1.3.6.1.4.1.5454.1.10.5
su	1.3.6.1.4.1.5454.1.10.3
sudb	1.3.6.1.4.1.5454.1.10.3.5
suInfoEntry	1.3.6.1.4.1.5454.1.10.3.6.1		not-accessible	Information about a specific subscriber unit retrieved by its ID number.
suInfoTable	1.3.6.1.4.1.5454.1.10.3.6		not-accessible	A table that contains subscriber unit entities.
NTF suLinkDown	1.3.6.1.4.1.5454.1.10.16.0.8			The SNMP trap that is generated when a specific SU Powered Off.
NTF suLinkUp	1.3.6.1.4.1.5454.1.10.16.0.7			The SNMP trap that is generated when a specific SU Associated.
tbw	1.3.6.1.4.1.5454.1
trango	1.3.6.1.4.1.5454
trapconfig	1.3.6.1.4.1.5454.1.10.4

RFC description

Management information for Trango M5800S wireless broadband access point and subscriber units.

Start monitoring Trango Systems M5800S fixed-wireless access point (operating-mode/RF-Ethernet throughput status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download TRANGOM5800S-MIB

This MIB depends on

Related MIBs

What Is TRANGOM5800S-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

RFC description