All MIBs › TN-CES-MIB
Organization: Transition Networks, Inc.
Last Updated: 2015-11-25
Category: Circuit Emulation, Transition Networks Media Converters
Description: Manages Transition Networks media converter circuit emulation service provisioning and status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TN-CES-MIB?
This is a Transition Networks proprietary MIB for its media-conversion/access product line, managing Circuit Emulation Service (CES), a technology that carries legacy TDM traffic transparently over a packet (Ethernet/IP) network. It exposes protocol configuration for the emulated circuit -- underlying transport type, UDP base port, SSRC checking, clock recovery algorithm/filter and its allowed maximum deviation -- plus event thresholds and notification objects. Its monitoring emphasis is on signal/clock integrity of the emulated circuit: the clock-recovery deviation and underrun objects directly reveal jitter-buffer underrun events and clock slip, which are the classic failure modes of TDM-over-packet circuits, and tnCesNotifications/tnCesEventId surface these as traps. As a device-specific MIB it doesn't lean on a broader standards MIB beyond generic SNMP conventions, though it parallels the general concept behind IETF pseudowire/CESoPSN work. It's typically deployed on Transition Networks media converters or NIDs providing TDM circuit emulation at the edge of a packet transport network. Network engineers evaluating or troubleshooting this functionality can download the TN-CES-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in TN-CES-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Transition Networks media converter/NID (Circuit Emulation Service device)
Monitoring Examples
An operator monitors tnCesClockRecoveryAlgorithm and tnCesClockRecoveryMaxDeviation together to confirm the clock-recovery mechanism is staying within tolerance, and watches tnCesProtocolUnderrunFixed/tnCesProtocolUnderrunValue for jitter-buffer underrun counts that indicate the emulated TDM circuit is experiencing packet-network congestion or delay variation. When tnCesEventThreshold is crossed within a tnCesEventReportingInterval window, the device raises a notification via tnCesNotifications/tnCesEventId, alerting the operator to a circuit-emulation quality event such as excessive underruns or an SSRC mismatch (tnCesProtocolEnableSSRCChecking).
What Can Be Monitored
- clock recovery deviation
- jitter-buffer underrun count
- event threshold crossings
- SSRC checking status
- UDP base port configuration
This MIB depends on
Related MIBs
Imported Objects
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressType |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| DisplayString | |
| MacAddress | |
| TruthValue |
From TRANSITION-SMI
| tnProducts | OBJECT-IDENTITY |
How to Use in IPNetwork Monitor
Example using tnCesProcessorProtocolMatch1 OID:
Select a Transition Networks media converter/NID, Circuit Emulation Service device (clock-recovery/jitter-buffer status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type tnCesProcessorProtocolMatch1 into the Find box to locate it in the OID tree, then select it and click OK. The number of frames which hit protocol matching rule 1. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| tnCesMIB | 1.3.6.1.4.1.868.2.5.60 | The MIB module for the Circuit Emulation Service. | ||
| tnCesNotifications | 1.3.6.1.4.1.868.2.5.60.0 | |||
| STR tnCesEventDetails | 1.3.6.1.4.1.868.2.5.60.0.1 | DisplayString | read-only | Text information describing the event that has occurred. |
| U32 tnCesEventPriority | 1.3.6.1.4.1.868.2.5.60.0.2 | Unsigned32 | read-only | Priority of this event. |
| tnCesEventId | 1.3.6.1.4.1.868.2.5.60.0.3 | |||
| tnCesEventIdGeneral | 1.3.6.1.4.1.868.2.5.60.0.3.0 | |||
| NTF tnCesGeneralEvent | 1.3.6.1.4.1.868.2.5.60.0.3.0.1 | Notification of an event relating to CES. | ||
| tnCesObjects | 1.3.6.1.4.1.868.2.5.60.1 | |||
| tnCesProtocol | 1.3.6.1.4.1.868.2.5.60.1.1 | |||
| INT tnCesProtocolType | 1.3.6.1.4.1.868.2.5.60.1.1.1 | INTEGER | read-write | Which network protocol to use for TDM over IP packets. Note that MPLS is not currenly supported. |
| T/F tnCesProtocolUnderrunFixed | 1.3.6.1.4.1.868.2.5.60.1.1.2 | TruthValue | read-write | Determins the underrun value in a TDM timeslot when no data was available in the logical link jitter buffer. When true, use the fixed value specified by tnCesProtocolUnderrunValue. When false, use the last value sent on the timeslot. |
| U32 tnCesProtocolUnderrunValue | 1.3.6.1.4.1.868.2.5.60.1.1.3 | Unsigned32 | read-write | Determins the underrun value in a TDM timeslot when no data was available in the logical link jitter buffer. Used when tnCesProtocolUnderrunFixed is false. |
| U32 tnCesProtocolUDPBasePort | 1.3.6.1.4.1.868.2.5.60.1.1.4 | Unsigned32 | read-write | The UDP port number used for the first logical link. The 2nd logical link uses this value plus one, and so on. Only relevent when tnCesProtocolType is ipUdpRtp. |
| T/F tnCesProtocolEnableSSRCChecking | 1.3.6.1.4.1.868.2.5.60.1.1.5 | TruthValue | read-write | Whether to check the RTP SSRC value on received packets. Disabling the check can be useful in aiding compatibility with equipment from other vendors. Only used when tnCesProtocolType is ipUdpRtp. |
| tnCesClockingAlternate | 1.3.6.1.4.1.868.2.5.60.1.2 | |||
| T/F tnCesClockingAlternateEnable | 1.3.6.1.4.1.868.2.5.60.1.2.1 | TruthValue | read-write | Whether to use the alternate clocking architecure which supports asymmeric and plesiosynchronous operation. |
| tnCesClockRecovery | 1.3.6.1.4.1.868.2.5.60.1.3 | |||
| INT tnCesClockRecoveryAlgorithm | 1.3.6.1.4.1.868.2.5.60.1.3.1 | INTEGER | read-write | Which algorithm to use for TDM over IP clock recovery. |
| INT tnCesClockRecoveryFilter | 1.3.6.1.4.1.868.2.5.60.1.3.2 | INTEGER | read-write | Which filter setting to use for TDM over IP clock recovery. |
| U32 tnCesClockRecoveryMaxDeviation | 1.3.6.1.4.1.868.2.5.60.1.3.3 | Unsigned32 | read-write | The maximum step change allowed in the recovered clock in PPM. |
| tnCesEvent | 1.3.6.1.4.1.868.2.5.60.1.4 | |||
| U32 tnCesEventThreshold | 1.3.6.1.4.1.868.2.5.60.1.4.1 | Unsigned32 | read-write | Priority threshold for reporting events related to CES. Events with a priority above this level are not reported to the system log or notified in SNMP traps. |
| U32 tnCesEventReportingInterval | 1.3.6.1.4.1.868.2.5.60.1.4.2 | Unsigned32 | read-write | How frequently to report certain CES events when thesholds are exceeded. The interval is specicifed in minutes. |
| U32 tnCesEventThresholdEarly | 1.3.6.1.4.1.868.2.5.60.1.4.3 | Unsigned32 | read-write | Threshold above which to report early packet errors. When this value is zero, reporting is disabled. |
| U32 tnCesEventThresholdLate | 1.3.6.1.4.1.868.2.5.60.1.4.4 | Unsigned32 | read-write | Threshold above which to report late packet errors. When this value is zero, reporting is disabled. |
| U32 tnCesEventThresholdUnderrun | 1.3.6.1.4.1.868.2.5.60.1.4.5 | Unsigned32 | read-write | Threshold above which to report underrun errors. When this value is zero, reporting is disabled. |
| U32 tnCesEventThresholdDCO | 1.3.6.1.4.1.868.2.5.60.1.4.6 | Unsigned32 | read-write | Threshold above which to report clock recovery DCO changes. When this value is zero, reporting is disabled. |
| tnCesProcessor | 1.3.6.1.4.1.868.2.5.60.1.5 | |||
| STR tnCesProcessorVersion | 1.3.6.1.4.1.868.2.5.60.1.5.1 | DisplayString | read-only | CES packet processor hardware and software version information. |
| C32 tnCesProcessorProtocolMatch1Ex | 1.3.6.1.4.1.868.2.5.60.1.5.2 | Counter32 | read-only | The number of frames which hit protocol matching rule 1. |
| C32 tnCesProcessorProtocolMatch2 | 1.3.6.1.4.1.868.2.5.60.1.5.3 | Counter32 | read-only | The number of frames which hit protocol matching rule 2. |
| C32 tnCesProcessorProtocolMatch3 | 1.3.6.1.4.1.868.2.5.60.1.5.4 | Counter32 | read-only | The number of frames which hit protocol matching rule 3. |
| C32 tnCesProcessorProtocolMatch4 | 1.3.6.1.4.1.868.2.5.60.1.5.5 | Counter32 | read-only | The number of frames which hit protocol matching rule 4. |
| C32 tnCesProcessorProtocolNoMatch | 1.3.6.1.4.1.868.2.5.60.1.5.6 | Counter32 | read-only | The number of frames which hit no protocol matching rules. |
| C32 tnCesProcessorClassifyFail | 1.3.6.1.4.1.868.2.5.60.1.5.7 | Counter32 | read-only | The number of frames which fail to classify. |
| C32 tnCesProcessorVerifyFail | 1.3.6.1.4.1.868.2.5.60.1.5.8 | Counter32 | read-only | The number of frames which fail to verify. |
| C32 tnCesProcessorIpv4ChecksumFail | 1.3.6.1.4.1.868.2.5.60.1.5.9 | Counter32 | read-only | The number of frames with IPV4 checksum failures. |
| C32 tnCesProcessorUdpChecksumFail | 1.3.6.1.4.1.868.2.5.60.1.5.10 | Counter32 | read-only | The number of frames with UDP checksum failures. |
| tnCesClockStatus | 1.3.6.1.4.1.868.2.5.60.1.6 | |||
| INT tnCesClockStatusLock | 1.3.6.1.4.1.868.2.5.60.1.6.1 | INTEGER | read-only | The CES processor DPLL lock status. |
| T/F tnCesClockStatusSlaveMode | 1.3.6.1.4.1.868.2.5.60.1.6.2 | TruthValue | read-only | Whether the CES processor clock is in slave (true) or master (false) mode. |
| STR tnCesClockStatusSource | 1.3.6.1.4.1.868.2.5.60.1.6.3 | DisplayString | read-only | Name of the current clock source. |
| tnCesTemperature | 1.3.6.1.4.1.868.2.5.60.1.7 | |||
| U32 tnCesTemperatureBoardWhole | 1.3.6.1.4.1.868.2.5.60.1.7.1 | Unsigned32 | read-only | Temperature measurement of circuit board. Whole part before the decimal point. |
| U32 tnCesTemperatureBoardFrac | 1.3.6.1.4.1.868.2.5.60.1.7.2 | Unsigned32 | read-only | Temperature measurement of circuit board. Fractional part after the decimal point. |
| U32 tnCesTemperatureProcessorWhole | 1.3.6.1.4.1.868.2.5.60.1.7.3 | Unsigned32 | read-only | Temperature measurement of processor. Whole part before the decimal point. |
| U32 tnCesTemperatureProcessorFrac | 1.3.6.1.4.1.868.2.5.60.1.7.4 | Unsigned32 | read-only | Temperature measurement of processor. Fractional part after the decimal point. |
| tnCesIP | 1.3.6.1.4.1.868.2.5.60.1.8 | |||
| IPt tnCesIpv4AddrType | 1.3.6.1.4.1.868.2.5.60.1.8.1 | InetAddressType | read-only | The IP address type associated with tnCesIpv4Addr. Has the value ipv4. |
| IP tnCesIpv4Addr | 1.3.6.1.4.1.868.2.5.60.1.8.2 | InetAddress | read-write | The IPv4 address to use for TDM over IP packets. Applies when the remote end of a circuit has an IPv4 address. |
| U32 tnCesIpv4PrefixLength | 1.3.6.1.4.1.868.2.5.60.1.8.3 | Unsigned32 | read-write | The prefix length associated with the CES IPv4 address. |
| IPt tnCesIpv6AddrType | 1.3.6.1.4.1.868.2.5.60.1.8.4 | InetAddressType | read-only | The IP address type associated with tnCesIpv6Addr. Has the value ipv6. |
| IP tnCesIpv6Addr | 1.3.6.1.4.1.868.2.5.60.1.8.5 | InetAddress | read-write | The IPv6 address to use for TDM over IP packets. Applies when the remote end of a circuit has an IPv6 address. |
| U32 tnCesIpv6PrefixLength | 1.3.6.1.4.1.868.2.5.60.1.8.6 | Unsigned32 | read-write | The prefix length associated with the CES IPv6 address. |
| tnCesClockPriority | 1.3.6.1.4.1.868.2.5.60.1.9 | |||
| tnCesMiscClockPriorityTable | 1.3.6.1.4.1.868.2.5.60.1.9.1 | not-accessible | Table of clock priorities for miscellaneous sources. | |
| tnCesMiscClockPriorityEntry | 1.3.6.1.4.1.868.2.5.60.1.9.1.1 | not-accessible | Each entry has the clock priority for a particular clock source. | |
| INT tnCesMiscClockPriorityItem | 1.3.6.1.4.1.868.2.5.60.1.9.1.1.1 | INTEGER | not-accessible | Which clock source this clock priority is for. |
| U32 tnCesMiscClockPriority | 1.3.6.1.4.1.868.2.5.60.1.9.1.1.2 | Unsigned32 | read-write | The clock priority of a clock source. A lower numeric value indicates a higher priority. |
| tnCesPRIClockPriorityTable | 1.3.6.1.4.1.868.2.5.60.1.9.2 | not-accessible | Table of clock priorities for TDM ports. | |
| tnCesPRIClockPriorityEntry | 1.3.6.1.4.1.868.2.5.60.1.9.2.1 | not-accessible | Each entry has the clock priority for a TDM port. | |
| U32 tnCesPRIClockPriorityIndex | 1.3.6.1.4.1.868.2.5.60.1.9.2.1.1 | Unsigned32 | not-accessible | Which TDM port this clock priority is for. |
| U32 tnCesPRIClockPriority | 1.3.6.1.4.1.868.2.5.60.1.9.2.1.2 | Unsigned32 | read-write | The clock priority of a TDM port. A lower numeric value indicates a higher priority. |
| tnCesLLClockPriorityTable | 1.3.6.1.4.1.868.2.5.60.1.9.3 | not-accessible | Table of clock priorities for logical link clock streams. | |
| tnCesLLClockPriorityEntry | 1.3.6.1.4.1.868.2.5.60.1.9.3.1 | not-accessible | Each entry has the clock priority for a logical link clock stream. | |
| U32 tnCesLLClockPriorityIndex | 1.3.6.1.4.1.868.2.5.60.1.9.3.1.1 | Unsigned32 | not-accessible | Which logical link clocking stream this clock priority is for. |
| U32 tnCesLLClockPriority | 1.3.6.1.4.1.868.2.5.60.1.9.3.1.2 | Unsigned32 | read-write | The clock priority of a logical link clock stream. A lower numeric value indicates a higher priority. |
| tnCesMulticastJoinTable | 1.3.6.1.4.1.868.2.5.60.1.10 | not-accessible | Table of multicast groups to join. | |
| tnCesMulticastJoinEntry | 1.3.6.1.4.1.868.2.5.60.1.10.1 | not-accessible | Each entry has the configuration for a multicast group to join. | |
| U32 tnCesMulticastJoinIndex | 1.3.6.1.4.1.868.2.5.60.1.10.1.1 | Unsigned32 | not-accessible | Index of multicast group. |
| T/F tnCesMulticastJoinAction | 1.3.6.1.4.1.868.2.5.60.1.10.1.2 | TruthValue | read-write | Whether to join a multicast group. When true, join the group specified by tnCesMulticastJoinAddr. When false, do not join any group and leave any previously joined goup. |
| IPt tnCesMulticastJoinAddrType | 1.3.6.1.4.1.868.2.5.60.1.10.1.3 | InetAddressType | read-write | The IP address type of the multicast group to join. Must be ipv4 or ipv6. |
| IP tnCesMulticastJoinAddr | 1.3.6.1.4.1.868.2.5.60.1.10.1.4 | InetAddress | read-write | The IP address of the multicast group to join. This must be a multicast address. |
| tnCesTDMTable | 1.3.6.1.4.1.868.2.5.60.1.11 | not-accessible | Table of TDM ports. | |
| tnCesTDMEntry | 1.3.6.1.4.1.868.2.5.60.1.11.1 | not-accessible | Each entry has the configuration for a TDM port. | |
| U32 tnCesTDMPortNumber | 1.3.6.1.4.1.868.2.5.60.1.11.1.1 | Unsigned32 | not-accessible | The TDM port number. |
| INT tnCesTDMPresentation | 1.3.6.1.4.1.868.2.5.60.1.11.1.2 | INTEGER | read-write | Network or user presentation. This options is not supported on all products. Modifications will be ignore on such products. |
| INT tnCesTDMFraming | 1.3.6.1.4.1.868.2.5.60.1.11.1.3 | INTEGER | read-write | Whether the TDM port operates in framed fractional or unframed full mode. It is not possible to set a port mode which would exclude any TDM channels that are assigned to a logical link (see tnCesLLChanSelectUsed). Any such channel must be deassigned first. |
| INT tnCesTDMMode | 1.3.6.1.4.1.868.2.5.60.1.11.1.4 | INTEGER | read-write | TDM port mode T1 or E1. It is not possible to set a port mode which would exclude any TDM channels that are assigned to a logical link (see tnCesLLChanSelectUsed). Any such channel must be deassigned first. |
| T/F tnCesTDMTS0Passthrough | 1.3.6.1.4.1.868.2.5.60.1.11.1.5 | TruthValue | read-write | Whether timeslot zero is passed in E1 fractional mode. Only valid when tnCesTDMFraming is fractional and tnCesTDMMode is E1. |
| T/F tnCesTDMCRC4 | 1.3.6.1.4.1.868.2.5.60.1.11.1.6 | TruthValue | read-write | Whether the TDM framing uses CRC4. Only valid when tnCesTDMFraming is fractional. |
| T/F tnCesTDMShutdownCallsOnFail | 1.3.6.1.4.1.868.2.5.60.1.11.1.7 | TruthValue | read-write | Whether to shutdown the CES connections or ISDN calls using this port when the port fails. |
| INT tnCesTDMImpedance | 1.3.6.1.4.1.868.2.5.60.1.11.1.8 | INTEGER | read-write | Electrical impedance of the TDM port, 75ohms or 120ohms. |
| INT tnCesTDMT1Framing | 1.3.6.1.4.1.868.2.5.60.1.11.1.9 | INTEGER | read-write | The frame structure in T1 mode. Only used when tnCesTDMMode is T1. |
| INT tnCesTDMT1LineCode | 1.3.6.1.4.1.868.2.5.60.1.11.1.10 | INTEGER | read-write | The line code in T1 mode. Only used when tnCesTDMMode is T1. |
| INT tnCesTDMT1LoopCodeType | 1.3.6.1.4.1.868.2.5.60.1.11.1.11 | INTEGER | read-write | The type of loop code which when detected on the port will cause loops to be switched on or off. |
| T/F tnCesTDMT1LoopCodeRxEnable | 1.3.6.1.4.1.868.2.5.60.1.11.1.12 | TruthValue | read-write | Whether detection of loop codes is enabled or disabled on the port. |
| U32 tnCesTDMT1LoopCodeUserUp | 1.3.6.1.4.1.868.2.5.60.1.11.1.13 | Unsigned32 | read-write | User defined bit pattern to cause loop up for the FACU option. |
| U32 tnCesTDMT1LoopCodeUserDown | 1.3.6.1.4.1.868.2.5.60.1.11.1.14 | Unsigned32 | read-write | User defined bit pattern to cause loop down for the FACU option. |
| U32 tnCesTDMT1LoopCodeUserLength | 1.3.6.1.4.1.868.2.5.60.1.11.1.15 | Unsigned32 | read-write | The number of bits in tnCesTDMT1LoopCodeUserUp and tnCesTDMT1LoopCodeUserDown. |
| T/F tnCesTDMDTE | 1.3.6.1.4.1.868.2.5.60.1.11.1.16 | TruthValue | read-write | Whether the port is configured as DTE (true) or DCE (false). Only applies to Contra ports. |
| tnCesLLTable | 1.3.6.1.4.1.868.2.5.60.1.12 | not-accessible | Table of logical link configuration. | |
| tnCesLLEntry | 1.3.6.1.4.1.868.2.5.60.1.12.1 | not-accessible | Each entry has the current configuration of a logical link. | |
| U32 tnCesLLNumber | 1.3.6.1.4.1.868.2.5.60.1.12.1.1 | Unsigned32 | not-accessible | The logical link number. |
| STR tnCesLLname | 1.3.6.1.4.1.868.2.5.60.1.12.1.2 | DisplayString | read-write | An optional name for the logical link. |
| INT tnCesLLDirection | 1.3.6.1.4.1.868.2.5.60.1.12.1.3 | INTEGER | read-write | Direction of data flow over the packet network for a logical link. |
| IPt tnCesLLRemoteIpAddrType | 1.3.6.1.4.1.868.2.5.60.1.12.1.4 | InetAddressType | read-write | The IP address type of the remote end of the logical link. Must be ipv4 or ipv6. |
| IP tnCesLLRemoteIpAddr | 1.3.6.1.4.1.868.2.5.60.1.12.1.5 | InetAddress | read-write | The IP address of the remote end of the logical link. If tnCesLLDirection is tx or both then this may be a unicast or multicast address. If tnCesLLDirection is rx then this must be a unicast address. |
| IPt tnCesLLSecondaryRemoteIpAddrType | 1.3.6.1.4.1.868.2.5.60.1.12.1.6 | InetAddressType | read-write | The secondary IP address type of the remote end of the logical link. Must be ipv4 or ipv6. |
| IP tnCesLLSecondaryRemoteIpAddr | 1.3.6.1.4.1.868.2.5.60.1.12.1.7 | InetAddress | read-write | The secondary IP address of the remote end of the logical link. If tnCesLLDirection is tx or both then this may be a unicast or multicast address. If tnCesLLDirection is rx then this must be a unicast address. |
| INT tnCesLLQosType | 1.3.6.1.4.1.868.2.5.60.1.12.1.8 | INTEGER | read-write | Whether logical link QOS is encoded as Type of Service (TOS) or Diffserv. |
| U32 tnCesLLQosTOS | 1.3.6.1.4.1.868.2.5.60.1.12.1.9 | Unsigned32 | read-write | Type Of Service value for logical link QOS. Only used when tnCesLLQosType is tos. |
| U32 tnCesLLQosDiffserv | 1.3.6.1.4.1.868.2.5.60.1.12.1.10 | Unsigned32 | read-write | Diffserv codepoint value for logical link QOS. Only used when tnCesLLQosType is diffserv. |
| T/F tnCesLLVlanTag | 1.3.6.1.4.1.868.2.5.60.1.12.1.11 | TruthValue | read-write | Whether Ethernet frames for this logical link are VLAN tagged. |
| U32 tnCesLLVlanId | 1.3.6.1.4.1.868.2.5.60.1.12.1.12 | Unsigned32 | read-write | VLAN ID for Ethernet frames for this logical link. Only applies when tnCesLLVlanTag is true. |
| U32 tnCesLLVlanPriority | 1.3.6.1.4.1.868.2.5.60.1.12.1.13 | Unsigned32 | read-write | Priority value for Ethernet frames for this logical link. Only applies when tnCesLLVlanTag is true. |
| U32 tnCesLLJitterBufferLength | 1.3.6.1.4.1.868.2.5.60.1.12.1.14 | Unsigned32 | read-write | Jitter buffer length in ms for this logical link. |
| U32 tnCesLLFramesPerPacket | 1.3.6.1.4.1.868.2.5.60.1.12.1.15 | Unsigned32 | read-write | In framed mode, the number of TDM frames in the packet payload for this logical link. |
| U32 tnCesLLRemoteLinkNumber | 1.3.6.1.4.1.868.2.5.60.1.12.1.16 | Unsigned32 | read-write | The remote logical link number that this link exchanges packets with. |
| tnCesLLSchedTable | 1.3.6.1.4.1.868.2.5.60.1.13 | not-accessible | Table of logical link schedule configuration. | |
| tnCesLLSchedEntry | 1.3.6.1.4.1.868.2.5.60.1.13.1 | not-accessible | Each entry has the current configuration of a logical link schedule. | |
| U32 tnCesLLSchedNumber | 1.3.6.1.4.1.868.2.5.60.1.13.1.1 | Unsigned32 | not-accessible | The logical link number. |
| T/F tnCesLLSchedEnable | 1.3.6.1.4.1.868.2.5.60.1.13.1.2 | TruthValue | read-write | Whether to enable the logical link schedule. When false, there is no scheduling and this link is always on. When true, the link is enabled according to its schedule. |
| U32 tnCesLLSchedStartTimeMonHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.3 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStartTimeMonMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.4 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStopTimeMonHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.5 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStopTimeMonMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.6 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStartTimeTueHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.7 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStartTimeTueMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.8 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStopTimeTueHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.9 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStopTimeTueMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.10 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStartTimeWedHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.11 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStartTimeWedMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.12 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStopTimeWedHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.13 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStopTimeWedMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.14 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStartTimeThuHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.15 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStartTimeThuMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.16 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStopTimeThuHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.17 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStopTimeThuMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.18 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStartTimeFriHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.19 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStartTimeFriMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.20 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStopTimeFriHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.21 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStopTimeFriMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.22 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStartTimeSatHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.23 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStartTimeSatMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.24 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStopTimeSatHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.25 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStopTimeSatMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.26 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStartTimeSunHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.27 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStartTimeSunMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.28 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLSchedStopTimeSunHours | 1.3.6.1.4.1.868.2.5.60.1.13.1.29 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLSchedStopTimeSunMins | 1.3.6.1.4.1.868.2.5.60.1.13.1.30 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| tnCesLLJATable | 1.3.6.1.4.1.868.2.5.60.1.14 | not-accessible | Table of logical link dynamic jitter buffer adjustment configuration. | |
| tnCesLLJAEntry | 1.3.6.1.4.1.868.2.5.60.1.14.1 | not-accessible | Each entry has the current dynamic jitter adjustment configuration of a logical link. | |
| U32 tnCesLLJANumber | 1.3.6.1.4.1.868.2.5.60.1.14.1.1 | Unsigned32 | not-accessible | The logical link number. |
| INT tnCesLLJitterAdjustmentMode | 1.3.6.1.4.1.868.2.5.60.1.14.1.2 | INTEGER | read-write | The mode in which automatic jitter buffer adustment is to be run. None - No automatic adjuistment of the jitter buffer will be carried out for this logical link. Always - Automatic jitter buffer adjustment is carried out periodically for this logical link while it is active. Schedule - Automatic jitter buffer adjustment is carried out periodically while this link is active during the specified schedule times. Once - Automatic jitter buffer adjustment is carried out once after this logical link becomes active. |
| U32 tnCesLLJitterAdjustmentAfter | 1.3.6.1.4.1.868.2.5.60.1.14.1.3 | Unsigned32 | read-write | How long to wait in minutes before doing any jitter buffer adjustment once the logical link has become active. Only used when tnCesLLJitterAdjustmentMode is always or once. |
| U32 tnCesLLJASchedStartTimeMonHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.4 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStartTimeMonMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.5 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStopTimeMonHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.6 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStopTimeMonMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.7 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStartTimeTueHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.8 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStartTimeTueMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.9 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStopTimeTueHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.10 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStopTimeTueMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.11 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStartTimeWedHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.12 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStartTimeWedMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.13 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStopTimeWedHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.14 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStopTimeWedMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.15 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStartTimeThuHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.16 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStartTimeThuMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.17 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStopTimeThuHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.18 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStopTimeThuMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.19 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStartTimeFriHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.20 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStartTimeFriMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.21 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStopTimeFriHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.22 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStopTimeFriMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.23 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStartTimeSatHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.24 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStartTimeSatMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.25 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStopTimeSatHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.26 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStopTimeSatMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.27 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStartTimeSunHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.28 | Unsigned32 | read-write | Hours component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStartTimeSunMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.29 | Unsigned32 | read-write | Minutes component of schedule start time. The start time must not be later than the stop time. |
| U32 tnCesLLJASchedStopTimeSunHours | 1.3.6.1.4.1.868.2.5.60.1.14.1.30 | Unsigned32 | read-write | Hours component of schedule stop time. The stop time must not be earlier than the start time. |
| U32 tnCesLLJASchedStopTimeSunMins | 1.3.6.1.4.1.868.2.5.60.1.14.1.31 | Unsigned32 | read-write | Minutes component of schedule stop time. The stop time must not be earlier than the start time. |
| tnCesLLChanSelectTable | 1.3.6.1.4.1.868.2.5.60.1.15 | not-accessible | Table of TDM channels selected for a logical link. | |
| tnCesLLChanSelectEntry | 1.3.6.1.4.1.868.2.5.60.1.15.1 | not-accessible | Each entry has the channel selection configuration of a logical link. | |
| U32 tnCesLLChanSelectLLNumber | 1.3.6.1.4.1.868.2.5.60.1.15.1.1 | Unsigned32 | not-accessible | The logical link number. |
| U32 tnCesLLChanSelectPortNumber | 1.3.6.1.4.1.868.2.5.60.1.15.1.2 | Unsigned32 | not-accessible | The TDM or RS530 port number. |
| U32 tnCesLLChanSelectAvailable | 1.3.6.1.4.1.868.2.5.60.1.15.1.3 | Unsigned32 | read-only | Bitmap of whether each channel on this TDM port is available for use by this logical link. Channels are unavailable if they unavailable in the TDM port configuration (full/fractional/E1/T1) or are already selected for another logical link. Bit 0 is for the first channel, bit one for the second, etc. |
| U32 tnCesLLChanSelectUsed | 1.3.6.1.4.1.868.2.5.60.1.15.1.4 | Unsigned32 | read-write | Bitmap of whether each channel on this TDM port is assigned for use by this logical link. A channel cannot be assigned to a logical link if the channel is unavailable in the TDM port configuration (full/fractional/E1/T1), the channel is already assigned to another logical link, the channel is on a different TDM port from other channels in this link, or the logical link would have more than 32 channels assigned. Bit 0 is for the first channel, bit one for the second, etc. For products with RS530 ports, this item is ignored. The channels used will be configured automatically from the serial port bitrate whenever this table entry is updated. |
| tnCesLLAlternateTable | 1.3.6.1.4.1.868.2.5.60.1.16 | not-accessible | Table of logical link configuration items for the alternate clocking mode. | |
| tnCesLLAlternateEntry | 1.3.6.1.4.1.868.2.5.60.1.16.1 | not-accessible | Each entry has the logical link configuration for the alternate clocking mode. | |
| U32 tnCesLLAlternateLLNumber | 1.3.6.1.4.1.868.2.5.60.1.16.1.1 | Unsigned32 | not-accessible | The clocking stream / logical link number. |
| T/F tnCesLLPlesiosynchronous | 1.3.6.1.4.1.868.2.5.60.1.16.1.2 | TruthValue | read-write | Whether clocking for stream is plesiosynchronous. Only used when tnCesClockingAlternateEnable is true. |
| T/F tnCesLLAsymmetric | 1.3.6.1.4.1.868.2.5.60.1.16.1.3 | TruthValue | read-write | Asymmetric clocking mode. Only applies when the associated TDM port is full and when tnCesClockingAlternateEnable is true. |
| U32 tnCesLLBytesPerPacketRx | 1.3.6.1.4.1.868.2.5.60.1.16.1.4 | Unsigned32 | read-write | In unframed mode, the number of bytes in the packet payload for the logical link in the receive direction. |
| U32 tnCesLLBytesPerPacketTx | 1.3.6.1.4.1.868.2.5.60.1.16.1.5 | Unsigned32 | read-write | In unframed mode, the number of bytes in the packet payload for the logical link in the transmit direction. |
| tnCesLLStatusTable | 1.3.6.1.4.1.868.2.5.60.1.17 | not-accessible | Table of logical link status. | |
| tnCesLLStatusEntry | 1.3.6.1.4.1.868.2.5.60.1.17.1 | not-accessible | Each entry has the current status of a logical link. | |
| U32 tnCesLLStatusNumber | 1.3.6.1.4.1.868.2.5.60.1.17.1.1 | Unsigned32 | not-accessible | The logical link number. |
| T/F tnCesLLStatusEnabled | 1.3.6.1.4.1.868.2.5.60.1.17.1.2 | TruthValue | read-only | Whether the logical link is enabled for use. |
| T/F tnCesLLStatusActive | 1.3.6.1.4.1.868.2.5.60.1.17.1.3 | TruthValue | read-only | Whether the logical link is active. |
| T/F tnCesLLStatusArpResolved | 1.3.6.1.4.1.868.2.5.60.1.17.1.4 | TruthValue | read-only | Whether address resolution has been completed for the logical link. |
| U32 tnCesLLStatusNumberOfChannels | 1.3.6.1.4.1.868.2.5.60.1.17.1.5 | Unsigned32 | read-only | The number of TDM channels being transported by this logical link. |
| MAC tnCesLLStatusRemoteMac | 1.3.6.1.4.1.868.2.5.60.1.17.1.6 | MacAddress | read-only | The MAC address of the remote end of the logical link, or the gateway MAC address when the remote end is on a different IP subnet. |
| IPt tnCesLLStatusRemoteIpAddrType | 1.3.6.1.4.1.868.2.5.60.1.17.1.7 | InetAddressType | read-only | The IP address type of the remote end of the logical link. |
| IP tnCesLLStatusRemoteIpAddr | 1.3.6.1.4.1.868.2.5.60.1.17.1.8 | InetAddress | read-only | The IP address of the remote end of the logical link. |
| T/F tnCesLLStatusRemoteContextKnown | 1.3.6.1.4.1.868.2.5.60.1.17.1.9 | TruthValue | read-only | Whether the logical link number on the remote end is known. |
| U32 tnCesLLStatusRemoteContextNumber | 1.3.6.1.4.1.868.2.5.60.1.17.1.10 | Unsigned32 | read-only | The logical link number on the remote end (if known). |
| T/F tnCesLLStatusRemotePortKnown | 1.3.6.1.4.1.868.2.5.60.1.17.1.11 | TruthValue | read-only | Whether the UDP port number of the remote end of the logical link is known. |
| U32 tnCesLLStatusRemotePort | 1.3.6.1.4.1.868.2.5.60.1.17.1.12 | Unsigned32 | read-only | The UDP port number of the remote end of the logical link (if known). |
| T/F tnCesLLStatusQueueLengthValid | 1.3.6.1.4.1.868.2.5.60.1.17.1.13 | TruthValue | read-only | Whether the jitter buffer statistics are available for the logical link. |
| U32 tnCesLLStatusMinQueueLength | 1.3.6.1.4.1.868.2.5.60.1.17.1.14 | Unsigned32 | read-only | The minimum fill level of the logical link jitter buffer. |
| U32 tnCesLLStatusMaxQueueLength | 1.3.6.1.4.1.868.2.5.60.1.17.1.15 | Unsigned32 | read-only | The maximum fill level of the logical link jitter buffer. |
| U32 tnCesLLStatusAveQueueLengthWhole | 1.3.6.1.4.1.868.2.5.60.1.17.1.16 | Unsigned32 | read-only | The average fill level of the logical link jitter buffer. Whole part before the decimal point. |
| U32 tnCesLLStatusAveQueueLengthFrac | 1.3.6.1.4.1.868.2.5.60.1.17.1.17 | Unsigned32 | read-only | The average fill level of the logical link jitter buffer. Fractional part after the decimal point. |
| C32 tnCesLLStatusEarly | 1.3.6.1.4.1.868.2.5.60.1.17.1.18 | Counter32 | read-only | The number of packets which arrived too early to be put into the logical link jitter buffer. |
| C32 tnCesLLStatusLate | 1.3.6.1.4.1.868.2.5.60.1.17.1.19 | Counter32 | read-only | The number of packets which arrived too late to be put into the logical link jitter buffer. |
| C32 tnCesLLStatusUnderrun | 1.3.6.1.4.1.868.2.5.60.1.17.1.20 | Counter32 | read-only | The number of underruns on the TDM interface caused by missing packets in the logical link jitter buffer. |
| C32 tnCesLLStatusLastSequence | 1.3.6.1.4.1.868.2.5.60.1.17.1.21 | Counter32 | read-only | The sequence number of the last packet received for the logical link. |
| C32 tnCesLLStatusPacketsRx | 1.3.6.1.4.1.868.2.5.60.1.17.1.22 | Counter32 | read-only | The number of packets received on the logical link. |
| C32 tnCesLLStatusPacketsTx | 1.3.6.1.4.1.868.2.5.60.1.17.1.23 | Counter32 | read-only | The number of packets transmitted on the logical link. |
| C32 tnCesLLStatusSlipsReduceCount | 1.3.6.1.4.1.868.2.5.60.1.17.1.24 | Counter32 | read-only | The number of times the jitter buffer has been slipped to reduced latency. |
| C32 tnCesLLStatusSlipsExtendCount | 1.3.6.1.4.1.868.2.5.60.1.17.1.25 | Counter32 | read-only | The number of times the jitter buffer has been slipped to extend latency. |
| T/F tnCesLLLocalLoop | 1.3.6.1.4.1.868.2.5.60.1.17.1.26 | TruthValue | read-write | Whether the logical link local loop is enabled. |
| T/F tnCesLLRemoteLoop | 1.3.6.1.4.1.868.2.5.60.1.17.1.27 | TruthValue | read-write | Whether the logical link remote loop is enabled. |
| I32 tnCesLLNudge | 1.3.6.1.4.1.868.2.5.60.1.17.1.28 | Integer32 | read-write | The number of packets by which to nudge the jitter buffer for this logical link. A positive number extends the latency, a negative number reduces the latency, zero has no effect. |
| T/F tnCesLLResetErrorStats | 1.3.6.1.4.1.868.2.5.60.1.17.1.29 | TruthValue | read-write | Set to true to reset the jitter buffer error counts for this logical link. |
| tnCesTDMStatusTable | 1.3.6.1.4.1.868.2.5.60.1.18 | not-accessible | Table of TDM port status. | |
| tnCesTDMStatusEntry | 1.3.6.1.4.1.868.2.5.60.1.18.1 | not-accessible | Each entry has the current status of a TDM port. | |
| U32 tnCesTDMStatusNumber | 1.3.6.1.4.1.868.2.5.60.1.18.1.1 | Unsigned32 | not-accessible | The TDM port number. |
| STR tnCesTDMStatusPhysical | 1.3.6.1.4.1.868.2.5.60.1.18.1.2 | DisplayString | read-only | Physical layer state of the TDM port. |
| STR tnCesTDMStatusRxSignalLevel | 1.3.6.1.4.1.868.2.5.60.1.18.1.3 | DisplayString | read-only | Receive signal level on the TDM port. |
| STR tnCesTDMStatusRxError | 1.3.6.1.4.1.868.2.5.60.1.18.1.4 | DisplayString | read-only | Receive error status of the TDM port. |
| T/F tnCesTDMLocalLoop | 1.3.6.1.4.1.868.2.5.60.1.18.1.5 | TruthValue | read-write | Whether the TDM port local loop is enabled. |
| T/F tnCesTDMRemoteLoop | 1.3.6.1.4.1.868.2.5.60.1.18.1.6 | TruthValue | read-write | Whether the TDM port remote loop is enabled. |
| T/F tnCesTDMBreakCalls | 1.3.6.1.4.1.868.2.5.60.1.18.1.7 | TruthValue | read-write | Set to true to break the CES connections or ISDN calls active on this port. |
| tnCesCallStatusTable | 1.3.6.1.4.1.868.2.5.60.1.19 | not-accessible | Table of calls. | |
| tnCesCallStatusEntry | 1.3.6.1.4.1.868.2.5.60.1.19.1 | not-accessible | Each entry has the current status of a CES call. | |
| U32 tnCesCallStatusNumber | 1.3.6.1.4.1.868.2.5.60.1.19.1.1 | Unsigned32 | not-accessible | The CES call number. |
| DAT tnCesCallStatusStartTime | 1.3.6.1.4.1.868.2.5.60.1.19.1.2 | DateAndTime | read-only | Time the call was started. |
| STR tnCesCallStatusSource | 1.3.6.1.4.1.868.2.5.60.1.19.1.3 | DisplayString | read-only | Source interface of the call. |
| STR tnCesCallStatusDestination | 1.3.6.1.4.1.868.2.5.60.1.19.1.4 | DisplayString | read-only | Destination interface of the call. |
| T/F tnCesCallStatusOriginator | 1.3.6.1.4.1.868.2.5.60.1.19.1.5 | TruthValue | read-only | Whether this system originated the call. |
| STR tnCesCallStatusDestinationNumber | 1.3.6.1.4.1.868.2.5.60.1.19.1.6 | DisplayString | read-only | Destination number of the call. |
| STR tnCesCallStatusSourceNumber | 1.3.6.1.4.1.868.2.5.60.1.19.1.7 | DisplayString | read-only | Source number of the call. |
| STR tnCesCallStatusState | 1.3.6.1.4.1.868.2.5.60.1.19.1.8 | DisplayString | read-only | State of the call. |
| tnCesClockStatusTable | 1.3.6.1.4.1.868.2.5.60.1.20 | not-accessible | Table of clock recovery status. | |
| tnCesClockStatusEntry | 1.3.6.1.4.1.868.2.5.60.1.20.1 | not-accessible | Each entry has the current status of a CES clock stream. | |
| U32 tnCesClockStatusStreamNumber | 1.3.6.1.4.1.868.2.5.60.1.20.1.1 | Unsigned32 | not-accessible | The CES clock stream number. |
| INT tnCesClockStatusStreamStatus | 1.3.6.1.4.1.868.2.5.60.1.20.1.2 | INTEGER | read-only | Status of the clock recovery on the clock stream. |
| INT tnCesClockStatusStreamMode | 1.3.6.1.4.1.868.2.5.60.1.20.1.3 | INTEGER | read-only | The clock recovery algorithm running on the clock stream, or disabled if no clock recovery is running. |
| I32 tnCesClockStatusStreamDCO | 1.3.6.1.4.1.868.2.5.60.1.20.1.4 | Integer32 | read-only | Recovered clock frequency offset in PPB. NB Limited to 32 bit range. |
| I32 tnCesClockStatusStreamDCOMin | 1.3.6.1.4.1.868.2.5.60.1.20.1.5 | Integer32 | read-only | Minimum value of the recovered clock frequency offset in PPB. NB Limited to 32 bit range. |
| I32 tnCesClockStatusStreamDCOMax | 1.3.6.1.4.1.868.2.5.60.1.20.1.6 | Integer32 | read-only | Maximum value of the recovered clock frequency offset in PPB. NB Limited to 32 bit range. |
| I32 tnCesClockStatusStreamDCOAvg | 1.3.6.1.4.1.868.2.5.60.1.20.1.7 | Integer32 | read-only | Average value of the recovered clock frequency offset in PPB. NB Limited to 32 bit range. |
| tnCesDebug | 1.3.6.1.4.1.868.2.5.60.1.21 | |||
| tnCesDebugTDMTable | 1.3.6.1.4.1.868.2.5.60.1.21.1 | not-accessible | Table of TDM port debug settings. | |
| tnCesDebugTDMEntry | 1.3.6.1.4.1.868.2.5.60.1.21.1.1 | not-accessible | Each entry has the debug setting for a TDM port. | |
| U32 tnCesDebugTDMPortNumber | 1.3.6.1.4.1.868.2.5.60.1.21.1.1.1 | Unsigned32 | not-accessible | The TDM port number. |
| T/F tnCesDebugTDMPortEnable | 1.3.6.1.4.1.868.2.5.60.1.21.1.1.2 | TruthValue | read-write | Whether to enable (true) or disable (false) debug on this TDM port. |
| tnCesDebugLLTable | 1.3.6.1.4.1.868.2.5.60.1.21.2 | not-accessible | Table of logical link debug settings. | |
| tnCesDebugLLEntry | 1.3.6.1.4.1.868.2.5.60.1.21.2.1 | not-accessible | Each entry has the current debug setting for a logical link. | |
| U32 tnCesDebugLLNumber | 1.3.6.1.4.1.868.2.5.60.1.21.2.1.1 | Unsigned32 | not-accessible | The logical link number. |
| T/F tnCesDebugLLEnable | 1.3.6.1.4.1.868.2.5.60.1.21.2.1.2 | TruthValue | read-write | Whether to enable (true) or disable (false) debug on this logical link. |
| tnCesDebugMiscTable | 1.3.6.1.4.1.868.2.5.60.1.21.3 | not-accessible | Table of miscellaneous debug settings. | |
| tnCesDebugMiscEntry | 1.3.6.1.4.1.868.2.5.60.1.21.3.1 | not-accessible | Each entry has the current debug setting for a miscellaneous item. | |
| INT tnCesDebugMiscItem | 1.3.6.1.4.1.868.2.5.60.1.21.3.1.1 | INTEGER | not-accessible | The debug item to enable or disable. |
| T/F tnCesDebugMiscEnable | 1.3.6.1.4.1.868.2.5.60.1.21.3.1.2 | TruthValue | read-write | Whether to enable (true) or disable (false) debug for this item. |
| tnCesRS530Table | 1.3.6.1.4.1.868.2.5.60.1.22 | not-accessible | Table of RS530 serial ports. | |
| tnCesRS530Entry | 1.3.6.1.4.1.868.2.5.60.1.22.1 | not-accessible | Each entry has the configuration for a RS530 serial port. | |
| U32 tnCesRS530PortNumber | 1.3.6.1.4.1.868.2.5.60.1.22.1.1 | Unsigned32 | not-accessible | The RS530 serial port number. |
| U32 tnCesRS530Rate | 1.3.6.1.4.1.868.2.5.60.1.22.1.2 | Unsigned32 | read-write | The RS530 serial port bit rate in bits per second. Valid rates are 64K to 2048K in 64K steps, or one of the following subrates: 38400, 19200, 9600, 4800, 2400. |
| T/F tnCesRS530ShutdownCallsOnFail | 1.3.6.1.4.1.868.2.5.60.1.22.1.3 | TruthValue | read-write | Whether to shutdown the CES connections using this port when the port fails. |
| tnCesRS530StatusTable | 1.3.6.1.4.1.868.2.5.60.1.23 | not-accessible | Table of RS530 serial port status. | |
| tnCesRS530StatusEntry | 1.3.6.1.4.1.868.2.5.60.1.23.1 | not-accessible | Each entry has the current status of a RS530 serial port. | |
| U32 tnCesRS530StatusNumber | 1.3.6.1.4.1.868.2.5.60.1.23.1.1 | Unsigned32 | not-accessible | The RS530 serial port number. |
| STR tnCesRS530InterfaceType | 1.3.6.1.4.1.868.2.5.60.1.23.1.2 | DisplayString | read-only | Describes the type of physical interface used by the RS530 serial. |
| T/F tnCesRS530StatusDTR | 1.3.6.1.4.1.868.2.5.60.1.23.1.3 | TruthValue | read-only | Status of the RS530 serial port C/DTR lead. |
| T/F tnCesRS530StatusDCD | 1.3.6.1.4.1.868.2.5.60.1.23.1.4 | TruthValue | read-only | Status of the RS530 serial port I/DCD lead. |
| T/F tnCesRS530StatusRTS | 1.3.6.1.4.1.868.2.5.60.1.23.1.5 | TruthValue | read-only | Status of the RS530 serial port RTS lead. |
| T/F tnCesRS530StatusCTS | 1.3.6.1.4.1.868.2.5.60.1.23.1.6 | TruthValue | read-only | Status of the RS530 serial port CTS lead. |
| T/F tnCesRS530StatusDSR | 1.3.6.1.4.1.868.2.5.60.1.23.1.7 | TruthValue | read-only | Status of the RS530 serial port DSR lead. |
| T/F tnCesRS530LocalLoop | 1.3.6.1.4.1.868.2.5.60.1.23.1.8 | TruthValue | read-write | Whether the RS530 serial port local loop is enabled. |
| T/F tnCesRS530RemoteLoop | 1.3.6.1.4.1.868.2.5.60.1.23.1.9 | TruthValue | read-write | Whether the RS530 port remote loop is enabled. |
| T/F tnCesRS530BreakCalls | 1.3.6.1.4.1.868.2.5.60.1.23.1.10 | TruthValue | read-write | Set to true to break the CES connections or ISDN calls active on this port. |
| tnCesConformance | 1.3.6.1.4.1.868.2.5.60.2 | |||
| tnCesCompliances | 1.3.6.1.4.1.868.2.5.60.2.1 | |||
| tnCesMIBCompliance | 1.3.6.1.4.1.868.2.5.60.2.1.1 | You will comply. Respect my authority! | ||
| tnCesGroups | 1.3.6.1.4.1.868.2.5.60.2.2 | |||
| tnCesGroup | 1.3.6.1.4.1.868.2.5.60.2.2.1 | Objects which implement CES support on a device. | ||
| tnCesTrapGroup | 1.3.6.1.4.1.868.2.5.60.2.2.2 | Notifications which implement CES support on a device. |
RFC description
TANDBERG Networks Circuit Emulation Service (CES) management MIB for video and audio conferencing endpoints.
Start monitoring Transition Networks media converter/NID, Circuit Emulation Service device (clock-recovery/jitter-buffer status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.