All MIBs › TIMETRA-SAS-QOS-MIB
Organization: Alcatel
Last Updated: 2007-01-01
Description: TIMETRA-SAS-QOS-MIB module
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is TIMETRA-SAS-QOS-MIB?
TIMETRA-SAS-QOS-MIB is part of Alcatel-Lucent's (now Nokia) TiMOS MIB family, providing Quality of Service management specifically for the SAS (Service Access Switch) variants of the Alcatel 7x50 platform, covering MPLS EXP-bit profile mapping and access/egress QoS policy objects. It exposes configuration data for mapping MPLS LSP EXP bits to QoS profiles, defining EXP profile tables, and managing access-egress QoS objects, which govern how traffic is classified and scheduled across the device. Its monitoring value is primarily around configuration/software state: operators verify that MPLS EXP-to-QoS profile mappings (tMplsLspExpProfMapTable) and EXP profile definitions (tMplsLspExpProfileTable) are correctly provisioned and unchanged, since a misconfigured mapping can cause traffic to receive the wrong forwarding treatment. Each TIMETRA-SAS-QOS-MIB OID within these tables corresponds to a specific EXP-bit-to-profile mapping or profile definition that operators check against the intended QoS policy. It depends heavily on the broader TIMETRA MIB family (chassis, VRTR, and related QoS modules) and on standard MPLS DiffServ/EXP-bit conventions for its semantics. It is deployed on Alcatel-Lucent/Nokia 7x50 SAS platforms used by service providers needing MPLS-aware QoS at the network access edge.
IPNetwork Monitor allows you to monitor SNMP objects defined in TIMETRA-SAS-QOS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Nokia/Alcatel-Lucent 7210 SAS service access switch product line, entire range (MPLS EXP-to-QoS profile mapping status)
Monitoring Examples
An operator would walk tMplsLspExpProfMapTable/tMplsLspExpProfMapEntry indexed by tMplsLspExpProfMapIndex to confirm each EXP-to-profile mapping's tMplsLspExpProfMapRowStatus and tMplsLspExpProfMapDescription match the intended QoS policy, and check tMplsLspExpProfileTable/tMplsLspExpProfileEntry for the tMplsLspExpProfileBits assigned to each profile. Monitoring tMplsLspExpProfMapLastChanged or tMplsLspExpProfileLastChanged lets an operator detect unexpected QoS policy changes without polling every mapping entry. An EXP profile mapping that doesn't match its documented tMplsLspExpProfMapDescription would signal drift between intended and actual MPLS QoS treatment.
What Can Be Monitored
- MPLS EXP-to-QoS profile mappings
- EXP profile bit definitions
- QoS mapping/profile row status
- last configuration change timestamps for QoS profiles
This MIB depends on
Related MIBs
Imported Objects
From ATM-TC-MIB
| AtmServiceCategory | |
| AtmTrafficDescrParamIndex |
From INET-ADDRESS-MIB
| InetAddressIPv6 | |
| InetAddressPrefixLength |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter64 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| MacAddress | |
| RowStatus | |
| StorageType | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
From TIMETRA-QOS-MIB
| tNetworkEgressFCEntry | OBJECT-TYPE |
| tNetworkPolicyEntry | OBJECT-TYPE |
| tNetworkPolicyIndex | OBJECT-TYPE |
| tNetworkQueueEntry | OBJECT-TYPE |
| tNetworkQueuePolicyEntry | OBJECT-TYPE |
| tPortSchedulerPlcyEntry | OBJECT-TYPE |
| tSapEgressEntry | OBJECT-TYPE |
| tSapEgressQueueEntry | OBJECT-TYPE |
| tSapIngressEntry | OBJECT-TYPE |
| tSapIngressFCEntry | OBJECT-TYPE |
| tSapIngressIPCriteriaEntry | OBJECT-TYPE |
| tSapIngressIPv6CriteriaEntry | OBJECT-TYPE |
| tSapIngressIndex | OBJECT-TYPE |
| tSapIngressMacCriteriaEntry | OBJECT-TYPE |
| tSapIngressQueueEntry | OBJECT-TYPE |
| tSlopePolicy | OBJECT-TYPE |
| tSlopePolicyEntry | OBJECT-TYPE |
From TIMETRA-SAP-MIB
| sapEncapValue | OBJECT-TYPE |
| sapPortId | OBJECT-TYPE |
| timetraSASConfs | OBJECT-IDENTITY |
| timetraSASModules | OBJECT-IDENTITY |
| timetraSASNotifyPrefix | OBJECT-IDENTITY |
| timetraSASObjs | OBJECT-IDENTITY |
From TIMETRA-SERV-MIB
| svcId | OBJECT-TYPE |
From TIMETRA-TC-MIB
| Dot1PPriority | |
| IpAddressPrefixLength | |
| ServiceAccessPoint | |
| TDEValue | |
| TDSCPName | |
| TDSCPNameOrEmpty | |
| TDSCPValue | |
| TDSCPValueOrNone | |
| TEgressQueueId | |
| TFCName | |
| TFCType | |
| TFrameType | |
| TIngressMeterId | |
| TIngressQueueId | |
| TIpProtocol | |
| TItemDescription | |
| TLspExpValue | |
| TMplsLspExpProfMapID | |
| TNamedItem | |
| TNamedItemOrEmpty | |
| TNetworkIngressMeterId | |
| TPortSchedulerCIR | |
| TPortSchedulerPIR | |
| TQueueId | |
| TSapIngressMeterId | |
| TTcpUdpPort | |
| TTcpUdpPortOperator |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| timetraSASQosMIBModule | 1.3.6.1.4.1.6527.6.2.1.1.5 | This document is the SNMP MIB module to manage and provision Quality of Service features on Alcatel 7x50 systems. Copyright 2003-2014 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel's proprietary intellectual property. Alcatel retains all title and ownership in the Specification, including any revisions. Alcatel grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification. | ||
| tmnxSASQosConformance | 1.3.6.1.4.1.6527.6.2.2.1.1 | |||
| tmnxSASQosCompliances | 1.3.6.1.4.1.6527.6.2.2.1.1.1 | |||
| tmnxSASQoSComp7210V1v0 | 1.3.6.1.4.1.6527.6.2.2.1.1.1.1 | The compliance statement for revision 1.0 of TIMETRA-SAS-QOS-MIB. | ||
| tmnxSASQoSComp7210V2v0 | 1.3.6.1.4.1.6527.6.2.2.1.1.1.2 | The compliance statement for revision 2.0 of TIMETRA-SAS-QOS-MIB. | ||
| tmnxSASQosGroups | 1.3.6.1.4.1.6527.6.2.2.1.1.2 | |||
| tmnxSASQoSV1v0Group | 1.3.6.1.4.1.6527.6.2.2.1.1.2.1 | sas group object definition | ||
| tmnxSASMQoSV1v0Group | 1.3.6.1.4.1.6527.6.2.2.1.1.2.2 | SAS M specific group object definition | ||
| tmnxSASQoSV2v0Group | 1.3.6.1.4.1.6527.6.2.2.1.1.2.3 | sas group object definition | ||
| tmnxSASQosObsolete7210V2v0Group | 1.3.6.1.4.1.6527.6.2.2.1.1.2.4 | The group of objects which are obsoleted from version 2.0 of Alcatel 7210 series systems. | ||
| tmnxSASQos7210V4v0Group | 1.3.6.1.4.1.6527.6.2.2.1.1.2.5 | The group of objects which are obsoleted from version 4.0 of Alcatel 7210 series systems. | ||
| tmnxSASQoSV10v0Group | 1.3.6.1.4.1.6527.6.2.2.1.1.2.6 | sas group object definition version 7.0 | ||
| tSASQosObjects | 1.3.6.1.4.1.6527.6.2.2.2.1 | |||
| tAccessEgressObjects | 1.3.6.1.4.1.6527.6.2.2.2.1.1 | |||
| tAccessEgressTable | 1.3.6.1.4.1.6527.6.2.2.2.1.1.1 | not-accessible | Information about all Access-egress policies. | |
| tAccessEgressEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.1.1.1 | not-accessible | Access Egress QoS information for a particular port | |
| TAC tAccessEgressIndex | 1.3.6.1.4.1.6527.6.2.2.2.1.1.1.1.1 | TAccessEgressPolicyID | not-accessible | the sap-egress policy ID is used as index for the table. |
| ROW tAccessEgressRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.1.1.1.2 | RowStatus | read-create | Row Status of this policy's entry. |
| TIT tAccessEgressScope | 1.3.6.1.4.1.6527.6.2.2.2.1.1.1.1.3 | TItemScope | read-create | scope of the sap-egress policy. |
| TIT tAccessEgressDescription | 1.3.6.1.4.1.6527.6.2.2.2.1.1.1.1.4 | TItemDescription | read-create | user-supplied description of this sap-egress policy. |
| TIM tAccessEgressLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.1.1.1.1.5 | TimeStamp | read-only | timestamp of last change to this row in tAccessEgressTable. |
| T/F tAccessEgressRemark | 1.3.6.1.4.1.6527.6.2.2.2.1.1.1.1.6 | TruthValue | read-create | This object specifies if the system will remark the egress packets or not. DEf val is TRUE for STU and FALSE for MTU |
| TRE tAccessEgressRemarkPolicyId | 1.3.6.1.4.1.6527.6.2.2.2.1.1.1.1.7 | TRemarkPolicyID | read-create | Remark Policy Id that be used when remarking is enabled. |
| INT tAccessEgressRemarkType | 1.3.6.1.4.1.6527.6.2.2.2.1.1.1.1.8 | INTEGER | read-create | This object specifies system remark type, tAccessEgressRemark will be set to true and tAccessEgressRemarkType will specify the remark type. |
| tAccessEgressQueueTable | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2 | not-accessible | information about all access-egress policies' queues. | |
| tAccessEgressQueueEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1 | not-accessible | Information about a particular sap-egress queue. Entries are created/deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile. | |
| TEG tAccessEgressQueueIndex | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.1 | TEgressQueueId | not-accessible | the number of a queue. zero is not allowed. for sap-egress, only three queues are allowed, so the queue index range is restricted. |
| ROW tAccessEgressQueueRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.2 | RowStatus | read-create | Row Status of the entry. |
| TBU tAccessEgressQueueCBS | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.3 | TBurstSize | read-create | The amount of reserved buffer space (in kilo bytes) for the queue. |
| TBU tAccessEgressQueueMBS | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.4 | TBurstSize | read-create | The maximum amount of buffer space (in kilo bytes) allowed for the queue. |
| TAD tAccessEgressQueuePIRAdaptation | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.5 | TAdaptationRule | read-create | The adaptation rule to be used while computing the operational PIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset. |
| TAD tAccessEgressQueueCIRAdaptation | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.6 | TAdaptationRule | read-create | The adaptation rule to be used while computing the operational CIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset. |
| TPI tAccessEgressQueueAdminPIR | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.7 | TPIRRate | read-create | The administrative PIR specified by the user. |
| TCI tAccessEgressQueueAdminCIR | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.8 | TCIRRate | read-create | The administrative CIR specified by the user. |
| TPI tAccessEgressQueueOperPIR | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.9 | TPIRRate | read-only | The administrative PIR specified by the user. |
| TCI tAccessEgressQueueOperCIR | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.10 | TCIRRate | read-only | The operational value derived by computing the CIR value from the administrative CIR and PIR values and their corresponding adaptation rules. |
| TIM tAccessEgressQueueLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.11 | TimeStamp | read-only | timestamp of last change to this row in tAccessEgressQueueTable. |
| TNA tAccessEgressQueuePolicyName | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.12 | TNamedItem | read-create | SapEgressQueuePolicyName determines the queue management policy attached to this SAP Egress queue. |
| INT tAccessEgressQueuePolicyQueueMode | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.13 | INTEGER | read-create | tAccessEgressQueuePolicyQueueMode specifies this policies mode. It has to be set when the policy is created. |
| INT tAccessEgressQueuePolicyWeight | 1.3.6.1.4.1.6527.6.2.2.2.1.1.2.1.14 | INTEGER | read-create | tAccessEgressQueuePolicyWeight specifies this policies weight. It is applicable only if queue mode is weighted. |
| tAccessEgressFCTable | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3 | not-accessible | ||
| tAccessEgressFCEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1 | not-accessible | Information about a particular access-egress policy's forwarding class mappings to queues and dot1p values. Entries are created/deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile. | |
| TFC tAccessEgressFCName | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1.1 | TFCName | not-accessible | forwarding class name. |
| ROW tAccessEgressFCRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1.2 | RowStatus | read-create | Row Status. |
| TEG tAccessEgressFCQueue | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1.3 | TEgressQueueId | read-create | The queue to use for packets in this forwarding class. No FC can map to the same queue being used by 'premium' class. You must specify a valid queue-id before setting the row status to active. |
| DOT tAccessEgressFCDot1PInProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1.4 | Dot1PPriority | read-create | the Dot1p to use for in-profile traffic. |
| DOT tAccessEgressFCDot1POutProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1.5 | Dot1PPriority | read-create | the Dot1p to use for in-profile traffic. |
| TIM tAccessEgressFCLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1.6 | TimeStamp | read-only | timestamp of last change to this row in tAccessEgressFCTable. |
| TDS tAccessEgressFCDscpInProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1.7 | TDSCPNameOrEmpty | read-write | The DSCP to use for in-profile traffic. |
| TDS tAccessEgressFCDscpOutProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1.8 | TDSCPNameOrEmpty | read-write | The DSCP to use for out-profile traffic. |
| DOT tAccessEgressFCDot1PProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1.9 | Dot1PPriority | read-create | the Dot1p to use for profile traffic. |
| TDE tAccessEgressFCForceDEValue | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1.10 | TDEValue | read-write | The value of tAccessEgressFCForceDEValue specifies the DE value to set for Access egress packets in this forwarding class regardless of profile status of the frames. An inconsistentValue error is returned if this object is set to any value other than '-1', when tAccessEgressFCDEMark object is set to 'false'. |
| T/F tAccessEgressFCDEMark | 1.3.6.1.4.1.6527.6.2.2.2.1.1.3.1.11 | TruthValue | read-write | The value of tAccessEgressFCDEMark specifies whether to set DE value in the frames of this forwarding class. An inconsistentValue error is returned if this object is set to 'false' when tAccessEgressFCForceDEValue object is not set to '-1'. |
| tSASSapIngressObjects | 1.3.6.1.4.1.6527.6.2.2.2.1.2 | |||
| tSapIngressMeterTable | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1 | not-accessible | Information about all sap-ingress policies' Meters. | |
| tSapIngressMeterEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1 | not-accessible | Information about a particular meter for a sap-ingress policy. Meter (1) is the used as a default for unicast and meter (11) is used as a default for multicast. Both these are created by the agent and can be edited but not removed from the system. Other entries are created by user. | |
| TSA tSapIngressMeter | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.1 | TSapIngressMeterId | not-accessible | The Meter ID is used as the secondary index to the table entry. |
| ROW tSapIngressMeterRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.2 | RowStatus | read-create | Row Status of the entry. This allows creation/deletion of rows in this table. |
| T/F tSapIngressMeterMCast | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.8 | TruthValue | read-create | This object specifies if this is a multicast meter or not. |
| TIN tSapIngressMeterCBS | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.10 | TIngressBurstSize | read-create | The amount of committed burst size (in kilo bits) for the meter. |
| TIN tSapIngressMeterMBS | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.11 | TIngressBurstSize | read-create | The maximum amount of burst size (in kilo bits) allowed for the meter. |
| TAD tSapIngressMeterPIRAdaptation | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.13 | TAdaptationRule | read-create | The adaptation rule to be used while computing the operational PIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset. |
| TAD tSapIngressMeterCIRAdaptation | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.14 | TAdaptationRule | read-create | The adaptation rule to be used while computing the operational CIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset. |
| TIN tSapIngressMeterAdminPIR | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.15 | TIngressPIRRate | read-create | The administrative PIR specified by the user. |
| TIN tSapIngressMeterAdminCIR | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.16 | TIngressCIRRate | read-create | The administrative CIR specified by the user. |
| TPI tSapIngressMeterOperPIR | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.17 | TPIRRate | read-only | The operational value derived by computing the PIR value from the administrative PIR value and their corresponding adaptation rules. |
| TCI tSapIngressMeterOperCIR | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.18 | TCIRRate | read-only | The operational value derived by computing the CIR value from the administrative CIR value and their corresponding adaptation rules. |
| TIM tSapIngressMeterLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.19 | TimeStamp | read-only | Timestamp of last change to this row in tSapIngressMeterTable. |
| TME tSapIngressMeterMode | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.21 | TMeterMode | read-create | This object is not used on SAS platform currently |
| TME tSapIngressMeterRateMode | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.22 | TMeterRateMode | read-create | Sap Ingress Meter Rate mode.The mode can be configured as Two Rate Three Color Marker (trTCM) or Single Rate Three Color Marker (srTCM). The mode command can be executed at anytime. |
| TIN tSapIngressMeterAdminCBS | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.23 | TIngressBurstSize | read-create | The administrative CBS specified by the user. The amount of committed burst size (in kilo bits) for the meter. |
| TIN tSapIngressMeterAdminMBS | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.24 | TIngressBurstSize | read-create | The administrative MBS specified by the user. The maximum amount of burst size (in kilo bits) allowed for the meter. |
| TIN tSapIngressMeterOperCBS | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.25 | TIngressBurstSize | read-only | The operational value derived by computing the CBS value from the administrative CBS value |
| TIN tSapIngressMeterOperMBS | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.26 | TIngressBurstSize | read-only | The operational value derived by computing the MBS value from the administrative MBS value |
| T/F tSapIngressMeterProfileMode | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.27 | TruthValue | read-create | The value of this object specifies whether the meter mode is color aware or color blind |
| INT tSapIngressMeterColorMode | 1.3.6.1.4.1.6527.6.2.2.2.1.2.1.1.28 | INTEGER | read-create | Set meter color mode |
| tSasSapIngressFCTable | 1.3.6.1.4.1.6527.6.2.2.2.1.2.2 | not-accessible | This table maintains the mapping of a particular forwarding class traffic into the specified meter. | |
| tSasSapIngressFCEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.2.2.1 | not-accessible | Information about a particular sap-ingress policy's forwarding class mappings to meters. | |
| TSA tSapIngressFCMeter | 1.3.6.1.4.1.6527.6.2.2.2.1.2.2.1.1 | TSapIngressMeterId | read-create | The specific meter to be used for packets in this forwarding class. A value of zero implies that the default meter should be used. |
| TSA tSapIngressFCMCastMeter | 1.3.6.1.4.1.6527.6.2.2.2.1.2.2.1.2 | TSapIngressMeterId | read-create | The specific multicast meter to be used for packets in this forwarding class. The meter is used only for specific entities and will be ignored wherever it is irrelevant. A value of zero implies that the default meters should be used. |
| TSA tSapIngressFCBCastMeter | 1.3.6.1.4.1.6527.6.2.2.2.1.2.2.1.3 | TSapIngressMeterId | read-create | The specific broadcast meter to be used for packets in this forwarding class. The meter is used only for specific entities and will be ignored wherever it is irrelevant. A value of zero implies that the default meters should be used. |
| TSA tSapIngressFCUnknownMeter | 1.3.6.1.4.1.6527.6.2.2.2.1.2.2.1.4 | TSapIngressMeterId | read-create | The specific unknown destination meter to be used for packets in this forwarding class. The meter is used only for specific entities and will be ignored wherever it is irrelevant. A value of zero implies that the default meters should be used. |
| sapIngQosMeterStatsTable | 1.3.6.1.4.1.6527.6.2.2.2.1.2.3 | not-accessible | A table that contains ingress QoS meter SAP statistics. | |
| sapIngQosMeterStatsEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.2.3.1 | not-accessible | Ingress statistics about a specific SAP's QoS meter. | |
| TSA sapIngQosMeterId | 1.3.6.1.4.1.6527.6.2.2.2.1.2.3.1.1 | TSapIngressMeterId | read-only | The index of the ingress QoS meter of this SAP. |
| C64 sapIngQosMeterStatsForwardedInProfPackets | 1.3.6.1.4.1.6527.6.2.2.2.1.2.3.1.10 | Counter64 | read-only | The number of in-profile packets (rate below CIR) forwarded by the ingress Qchip. |
| C64 sapIngQosMeterStatsForwardedOutProfPackets | 1.3.6.1.4.1.6527.6.2.2.2.1.2.3.1.11 | Counter64 | read-only | The number of out-of-profile packets (rate above CIR) forwarded by the ingress Qchip. |
| C64 sapIngQosMeterStatsForwardedInProfOctets | 1.3.6.1.4.1.6527.6.2.2.2.1.2.3.1.12 | Counter64 | read-only | The number of in-profile octets (rate below CIR) forwarded by the ingress Qchip. |
| C64 sapIngQosMeterStatsForwardedOutProfOctets | 1.3.6.1.4.1.6527.6.2.2.2.1.2.3.1.13 | Counter64 | read-only | The number of out-of-profile octets (rate above CIR) forwarded by the ingress Qchip. |
| C64 sapIngQosMeterStatsForwardedPackets | 1.3.6.1.4.1.6527.6.2.2.2.1.2.3.1.14 | Counter64 | read-only | The number of packets forwarded by the ingress Qchip. |
| C64 sapIngQosMeterStatsForwardedOctets | 1.3.6.1.4.1.6527.6.2.2.2.1.2.3.1.15 | Counter64 | read-only | The number of octets forwarded by the ingress Qchip. |
| C64 sapIngQosMeterStatsDroppedPackets | 1.3.6.1.4.1.6527.6.2.2.2.1.2.3.1.16 | Counter64 | read-only | The number of packets dropped by the ingress Qchip. |
| C64 sapIngQosMeterStatsDroppedOctets | 1.3.6.1.4.1.6527.6.2.2.2.1.2.3.1.17 | Counter64 | read-only | The number of octets dropped by the ingress Qchip. |
| tSapIngressExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4 | not-accessible | ||
| tSapIngressExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1 | not-accessible | ||
| U32 tSapIngressNumQosClassifiers | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.1 | Unsigned32 | read-create | The number of ingress QoS classifiers to be allocated to the SAP on which this policy is applied. The number of QoS classifiers required by a SAP ingress QoS policy should be less than or equal to its tSapIngressNumQosClassifiers. The number of Meters required by a SAP ingress QoS policy should be less than or equal to half the number of tSapIngressNumQosClassifiers. |
| U32 tSapIngressQosClassifiersUsed | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.2 | Unsigned32 | read-only | This value indicates the number of ingress QoS classifiers required when this policy is applied on a SAP. This value is calculated based on the number of classifiers required for a VPLS SAP. |
| U32 tSapIngressQosMetersUsed | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.3 | Unsigned32 | read-only | This value indicates the number of ingress QoS meters required when this policy is applied on a SAP. This value is calculated based on the number of meters required for a VPLS SAP. |
| U32 tSapIngressQosClassifiersRequiredInVpls | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.4 | Unsigned32 | read-only | This value indicates the number of ingress QoS classifiers required when this policy is applied on a SAP. This value is calculated based on the number of classifiers required for a VPLS SAP. |
| U32 tSapIngressQosClassifiersRequiredInEpipe | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.5 | Unsigned32 | read-only | This value indicates the number of ingress QoS classifiers required when this policy is applied on a SAP. This value is calculated based on the number of classifiers required for a EPIPE SAP. |
| U32 tSapIngressQosMetersRequiredInVpls | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.6 | Unsigned32 | read-only | This value indicates the number of ingress QoS meters required when this policy is applied on a SAP. This value is calculated based on the number of meters required for a VPLS SAP. |
| U32 tSapIngressQosMetersRequiredInEpipe | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.7 | Unsigned32 | read-only | This value indicates the number of ingress QoS meters required when this policy is applied on a SAP. This value is calculated based on the number of meters required for a EPIPE SAP. |
| INT tSapIngressIPCriteriaMatch | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.8 | INTEGER | read-create | This object specifies the basic match criteria as 'any' or 'dscp-only' based on ip. The default value is 'dscp-only' |
| INT tSapIngressMacCriteriaMatch | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.9 | INTEGER | read-create | This object specifies the basic match criteria as 'any' or 'dot1p-only' based on Mac Address. The default value is 'any' |
| TPR tSapIngressDefaultFCProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.10 | TProfileOrDei | read-create | tSapIngressDefaultFCProfile specifies the profile for the default fc |
| T/F tSapIngressIPv6CriteriaEnable | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.11 | TruthValue | read-create | tSapIngressIPv6CriteriaEnable is a boolean flag which allows/disallows configuring match criteria based on ipv6 address |
| INT tSapIngressIPv6CriteriaMatch | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.12 | INTEGER | read-create | This object specifies the basic match criteria as 'any' or 'dscp-only' based on ipv6. The default value is 'dscp-only' |
| INT tSapIngressIPMacMatch | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.13 | INTEGER | read-create | This object specifies the basic match criteria whether to match ip or mac criteria first |
| U32 tSapIngressQosClassifiersRequiredInIes | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.14 | Unsigned32 | read-only | This value indicates the number of ingress QoS classifiers required when this policy is applied on a SAP. This value is calculated based on the number of classifiers required for a IES SAP. |
| U32 tSapIngressQosMetersRequiredInIes | 1.3.6.1.4.1.6527.6.2.2.2.1.2.4.1.15 | Unsigned32 | read-only | This value indicates the number of ingress QoS classifiers required when this policy is applied on a SAP. This value is calculated based on the number of classifiers required for a IES SAP. |
| tSapIngressQueueExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.2.5 | not-accessible | Extension table to tSapIngressQueueTable | |
| tSapIngressQueueExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.2.5.1 | not-accessible | ||
| TNA tSapIngressQueuePolicyName | 1.3.6.1.4.1.6527.6.2.2.2.1.2.5.1.1 | TNamedItem | read-create | SapIngressQueuePolicyName determines the queue management policy attached to this SAP Ingress queue. |
| tSapIngressIPCriteriaExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.2.6 | not-accessible | information about sap-ingress policies extenstion to tSapIngressIPCriteriaEntry | |
| tSapIngressIPCriteriaExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.2.6.1 | not-accessible | Information about a particular ip-criteria entry for a sap-ingress policy. This is an extenstion to tSapIngressIPCriteriaEntry. | |
| TPR tSapIngressIPCriteriaActionProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.2.6.1.1 | TProfileOrDei | read-create | tSapIngressIPCriteriaActionProfile specifies the profile of the traffic that matches the specific IP criteria. The value none indicates that the profile is derived from ingress classification and profiling functions. |
| tSapIngressMacCriteriaExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.2.7 | not-accessible | Information about mac-criteria entries. Extenstion to tSapIngressMacCriteriaEntry | |
| tSapIngressMacCriteriaExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.2.7.1 | not-accessible | Information about a particular mac-criteria entry for a sap-ingress policy. Entries are created by user. Entries are deleted by user. There is no StorageType object, entries have a presumed StorageType of nonVolatile. | |
| TPR tSapIngressMacCriteriaActionProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.2.7.1.1 | TProfileOrDei | read-create | tSapIngressMacCriteriaActionProfile specifies the profile of the traffic that matches the specific MAC criteria. The value none indicates that the profile is derived from ingress classification and profiling functions. |
| tSapIngressIPv6CriteriaExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.2.8 | not-accessible | information about sap-ingress policies extenstion to tSapIngressIPv6CriteriaEntry | |
| tSapIngressIPv6CriteriaExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.2.8.1 | not-accessible | Information about a particular ip-criteria entry for a sap-ingress policy. This is an extenstion to tSapIngressIPv6CriteriaEntry. | |
| TPR tSapIngressIPv6CriteriaActionProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.2.8.1.1 | TProfileOrDei | read-create | tSapIngressIPv6CriteriaActionProfile specifies the profile of the traffic that matches the specific IP criteria. The value none indicates that the profile is derived from ingress classification and profiling functions. |
| tSASNetworkIngressObjects | 1.3.6.1.4.1.6527.6.2.2.2.1.3 | |||
| tNetworkIngressFCExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.3.1 | not-accessible | This table maintains the mapping of a particular forwarding class traffic into the specified meter. | |
| tNetworkIngressFCExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.3.1.1 | not-accessible | Information about a particular network-ingress policy's forwarding class mappings to meter. Entries are created and deleted by user. They have a presumed StorageType of nonVolatile. | |
| TNA tNetworkIngressFCExtnName | 1.3.6.1.4.1.6527.6.2.2.2.1.3.1.1.1 | TNamedItem | not-accessible | tNetworkIngressFCExtnName specifies the forwarding class for which this mapping is defined. |
| ROW tNetworkIngressFCExtnRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.3.1.1.2 | RowStatus | read-create | Row Status for this Entry. |
| TNE tNetworkIngressFCExtnMeter | 1.3.6.1.4.1.6527.6.2.2.2.1.3.1.1.3 | TNetworkIngressMeterId | read-create | The specific meter to be used for packets in this forwarding class. A value of zero implies that the default meters should be used. |
| TNE tNetworkIngressFCExtnMCastMeter | 1.3.6.1.4.1.6527.6.2.2.2.1.3.1.1.4 | TNetworkIngressMeterId | read-create | The specific multicast meter to be used for packets in this forwarding class. The meter is used only for specific entities and will be ignored wherever it is irrelevant. A value of zero implies that the default meters should be used. |
| TIM tNetworkIngressFCExtnLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.1.3.1.1.5 | TimeStamp | read-only | tNetworkIngressFCExtnLastChanged indicates the value of sysUpTime when the forwarding class entry was last modified. |
| tNetworkIngressMeterTable | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2 | not-accessible | information about all network policies' meters. | |
| tNetworkIngressMeterEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1 | not-accessible | Information about a particular meter for a network policy. Meter (1) is the used as a default for unicast and meter (9) is used as a default for multicast. Both these are created by the agent and can be edited but not removed from the system. Other entries are created by user. | |
| TNE tNetworkIngressMeterIndex | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.1 | TNetworkIngressMeterId | not-accessible | The Meter ID is used as the secondary index to the table entry. |
| ROW tNetworkIngressMeterRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.2 | RowStatus | read-create | Row Status of the entry. This allows creation/deletion of rows in this table. |
| TIN tNetworkIngressMeterCBS | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.3 | TIngressBurstSize | read-create | The amount of committed burst size (in kilo bits) for the meter. |
| TIN tNetworkIngressMeterMBS | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.4 | TIngressBurstSize | read-create | The maximum amount of burst size (in kilo bits) allowed for the meter. |
| TAD tNetworkIngressMeterCIRAdaptation | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.5 | TAdaptationRule | read-create | The adaptation rule to be used while computing the operational CIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset. |
| TAD tNetworkIngressMeterPIRAdaptation | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.6 | TAdaptationRule | read-create | The adaptation rule to be used while computing the operational PIR value. The adaptation rule specifies the rules to compute the operational values while maintaining minimum offset. |
| TIN tNetworkIngressMeterAdminPIR | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.7 | TIngressPIRRate | read-create | The administrative PIR specified by the user. |
| TIN tNetworkIngressMeterAdminCIR | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.8 | TIngressCIRRate | read-create | The administrative CIR specified by the user. |
| TPI tNetworkIngressMeterOperPIR | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.9 | TPIRRate | read-only | The operational value derived by computing the PIR value from the administrative PIR value and their corresponding adaptation rules. |
| TCI tNetworkIngressMeterOperCIR | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.10 | TCIRRate | read-only | The operational value derived by computing the CIR value from the administrative CIR value and their corresponding adaptation rules. |
| TIM tNetworkIngressMeterLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.11 | TimeStamp | read-only | Timestamp of last change to this row. |
| TME tNetworkIngressMeterMode | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.12 | TMeterMode | read-create | Network Ingress Meter Mode |
| T/F tNetworkIngressMeterMCast | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.13 | TruthValue | read-create | This object specifies if this is a multicast meter or not. |
| TME tNetworkIngressMeterRateMode | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.14 | TMeterRateMode | read-create | Network Ingress Meter Rate mode.The mode can be configured as Two Rate Three Color Marker (trTCM) or Single Rate Three Color Marker (srTCM). The mode command can be executed at anytime. |
| TIN tNetworkIngressMeterAdminCBS | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.15 | TIngressBurstSize | read-create | The administrative CBS specified by the user. The amount of committed burst size (in kilo bits) for the meter. |
| TIN tNetworkIngressMeterAdminMBS | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.16 | TIngressBurstSize | read-create | The administrative MBS specified by the user. The maximum amount of burst size (in kilo bits) allowed for the meter. |
| TIN tNetworkIngressMeterOperCBS | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.17 | TIngressBurstSize | read-only | The operational value derived by computing the CBS value from the administrative CBS value |
| TIN tNetworkIngressMeterOperMBS | 1.3.6.1.4.1.6527.6.2.2.2.1.3.2.1.26 | TIngressBurstSize | read-only | The operational value derived by computing the MBS value from the administrative MBS value |
| tSASSlopeObjects | 1.3.6.1.4.1.6527.6.2.2.2.1.4 | |||
| tSasSlopePolicyExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1 | not-accessible | Slope Policy Table. Additions for sas platform | |
| tSasSlopePolicyExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1 | not-accessible | Slope Policy Entry additions for sas platform. | |
| TSL tSlopeHiQueue1DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.1 | TSlopeDropRate | read-create | High Queue Drop Rate |
| TSL tSlopeHiQueue2DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.2 | TSlopeDropRate | read-create | High Queue Drop Rate |
| TSL tSlopeHiQueue3DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.3 | TSlopeDropRate | read-create | High Queue Drop Rate |
| TSL tSlopeHiQueue4DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.4 | TSlopeDropRate | read-create | High Queue Drop Rate |
| TSL tSlopeHiQueue5DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.5 | TSlopeDropRate | read-create | High Queue Drop Rate |
| TSL tSlopeHiQueue6DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.6 | TSlopeDropRate | read-create | High Queue Drop Rate |
| TSL tSlopeHiQueue7DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.7 | TSlopeDropRate | read-create | High Queue Drop Rate |
| TSL tSlopeHiQueue8DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.8 | TSlopeDropRate | read-create | High Queue Drop Rate |
| TSL tSlopeLoQueue1DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.9 | TSlopeDropRate | read-create | Low Queue Drop Rate |
| TSL tSlopeLoQueue2DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.10 | TSlopeDropRate | read-create | Low Queue Drop Rate |
| TSL tSlopeLoQueue3DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.11 | TSlopeDropRate | read-create | Low Queue Drop Rate |
| TSL tSlopeLoQueue4DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.12 | TSlopeDropRate | read-create | Low Queue Drop Rate |
| TSL tSlopeLoQueue5DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.13 | TSlopeDropRate | read-create | Low Queue Drop Rate |
| TSL tSlopeLoQueue6DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.14 | TSlopeDropRate | read-create | Low Queue Drop Rate |
| TSL tSlopeLoQueue7DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.15 | TSlopeDropRate | read-create | Low Queue Drop Rate |
| TSL tSlopeLoQueue8DropRate | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.16 | TSlopeDropRate | read-create | Low Queue Drop Rate |
| TSL tSlopeHiStartThreshold | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.17 | TSlopeThreshold | read-create | High slope Start Threshold.This object implies that once the shared buffer utilization reaches the start-threshold level then high-priority packets egressing out from a particular queue would be dropped at configured drop rate. |
| TSL tSlopeLoStartThreshold | 1.3.6.1.4.1.6527.6.2.2.2.1.4.1.1.18 | TSlopeThreshold | read-create | Low slope Start Threshold.This implies that once the shared buffer utilization reaches the start-threshold level then low-priority packets egressing out from a particular queue would be dropped at configured drop rate. |
| tSlopePolicyQueueTable | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2 | not-accessible | Slope Policy Per Queue Per Port additions for SAS-M platform. In SAS-M there are three slopes associated with a queue. One slope for Tcp Green packets, one for Tcp Yellow packets and one for Non Tcp Packets(both green and yellow packets). Each slope in turn can have four parameters defining its behavior | |
| tSlopePolicyQueueEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1 | not-accessible | ||
| TQU tSlopePolicyQueueId | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.1 | TQueueId | not-accessible | Queue for which slope policy is being defined |
| ROW tSlopePolicyQueueRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.2 | RowStatus | read-create | Row Status of the entry. This allows creation/deletion of rows in this table. |
| TIM tSlopePolicyQueueLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.3 | TimeStamp | read-only | Timestamp of last change to this row. |
| INT tSlopePolicyQueueHiAdminStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.4 | INTEGER | read-create | tSlopePolicyQueueHiAdminStatus specifies the admin state for the queue's high profile (Tcp Green Packets )slope. If the tSlopePolicyQueueHiAdminStatus is set to 'down',the slope is inactive. |
| U32 tSlopePolicyQueueHiStartAverage | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.5 | Unsigned32 | read-create | The percentage of the buffer utilized after which the drop probability starts to rise above 0. |
| U32 tSlopePolicyQueueHiMaxAverage | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.6 | Unsigned32 | read-create | The percentage of the buffer utilized after which the drop probability is 100 percent. This implies that all packets beyond this point will be dropped. |
| TMA tSlopePolicyQueueHiMaxProbability | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.7 | TMaxProbability | read-create | High Profile Max Probability.Defines the slope between the Start Average and Max Average |
| INT tSlopePolicyQueueLoAdminStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.8 | INTEGER | read-create | tSlopePolicyQueueLoAdminStatus specifies the admin state for the queue's low profile (Tcp Yellow Packets )slope. If the tSlopePolicyQueueLoAdminStatus is set to 'down',the slope is inactive. |
| U32 tSlopePolicyQueueLoStartAverage | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.9 | Unsigned32 | read-create | The percentage of the buffer utilized after which the drop probability starts to rise above 0. |
| U32 tSlopePolicyQueueLoMaxAverage | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.10 | Unsigned32 | read-create | The percentage of the buffer utilized after which the drop probability is 100 percent. This implies that all packets beyond this point will be dropped. |
| TMA tSlopePolicyQueueLoMaxProbability | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.11 | TMaxProbability | read-create | Low Profile Max Probability.Defines the slope between the Start Average and Max Average |
| INT tSlopePolicyQueueNonTcpAdminStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.12 | INTEGER | read-create | tSlopePolicyQueueNonTcpAdminStatus specifies the admin state for the queue's non tcp profile (Non Tcp Packets )slope. If the tSlopePolicyQueueNonTcpAdminStatus is set to 'down',the slope is inactive. |
| U32 tSlopePolicyQueueNonTcpStartAverage | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.13 | Unsigned32 | read-create | The percentage of the buffer utilized after which the drop probability starts to rise above 0. |
| U32 tSlopePolicyQueueNonTcpMaxAverage | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.14 | Unsigned32 | read-create | The percentage of the buffer utilized after which the drop probability is 100 percent. This implies that all packets beyond this point will be dropped. |
| TMA tSlopePolicyQueueNonTcpMaxProbability | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.15 | TMaxProbability | read-create | Non Tcp Profile Max Probability.Defines the slope between the Start Average and Max Average |
| U32 tSlopePolicyQueueTimeAvgFactor | 1.3.6.1.4.1.6527.6.2.2.2.1.4.2.1.16 | Unsigned32 | read-create | The time average factor describes the weighting between the previous shared buffer average utilization result and the new shared buffer utilization in determining the new shared buffer average utilization. |
| tSasSchedulerObjects | 1.3.6.1.4.1.6527.6.2.2.2.1.5 | |||
| tSasPortSchedulerPlcyTable | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1 | not-accessible | The tSasPortSchedulerPlcyTable has an entry for each port scheduler configured on this system. | |
| tSasPortSchedulerPlcyEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1.1 | not-accessible | Each row represents a particular port scheduler. Entries are created and deleted by the user. | |
| TPL tPortSchedulerPlcyMode | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1.1.1 | TPlcyMode | read-create | Port Scheduler Policy Mode |
| TPL tPortSchedulerPlcyQuanta | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1.1.2 | TPlcyQuanta | read-create | Port Scheduler Policy Quanta |
| TQW tPortSchedulerPlcyQueue1Weight | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1.1.3 | TQWeight | read-create | Port Scheduler Policy Queue 1 Weight |
| TQW tPortSchedulerPlcyQueue2Weight | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1.1.4 | TQWeight | read-create | Port Scheduler Policy Queue 2 Weight |
| TQW tPortSchedulerPlcyQueue3Weight | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1.1.5 | TQWeight | read-create | Port Scheduler Policy Queue 3 Weight |
| TQW tPortSchedulerPlcyQueue4Weight | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1.1.6 | TQWeight | read-create | Port Scheduler Policy Queue 4 Weight |
| TQW tPortSchedulerPlcyQueue5Weight | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1.1.7 | TQWeight | read-create | Port Scheduler Policy Queue 5 Weight |
| TQW tPortSchedulerPlcyQueue6Weight | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1.1.8 | TQWeight | read-create | Port Scheduler Policy Queue 6 Weight |
| TQW tPortSchedulerPlcyQueue7Weight | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1.1.9 | TQWeight | read-create | Port Scheduler Policy Queue 7 Weight |
| TQW tPortSchedulerPlcyQueue8Weight | 1.3.6.1.4.1.6527.6.2.2.2.1.5.1.1.10 | TQWeight | read-create | Port Scheduler Policy Queue 8 Weight |
| tQosFrameBasedAccntObjects | 1.3.6.1.4.1.6527.6.2.2.2.1.6 | |||
| T/F tQosIngressFrameBasedAccnt | 1.3.6.1.4.1.6527.6.2.2.2.1.6.1 | TruthValue | read-create | This object is used to enable frame based accounting for all the ingress meters in use by the system. When this is enabled the ingress meters account for the IFG (12 bytes) + SFD (8 bytes) overhead associated with Ethernet frame. |
| T/F tQosEgressFrameBasedAccnt | 1.3.6.1.4.1.6527.6.2.2.2.1.6.2 | TruthValue | read-create | This object is used to enable frame based accounting for all the egress queue shapers and the port egress rate shaper in use by the system. When this is enabled the shapers account for the IFG (12 bytes) + SFD (8 bytes) overhead associated with Ethernet frame. |
| tSASNetworkObjects | 1.3.6.1.4.1.6527.6.2.2.2.1.7 | |||
| tNetworkPolicyExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.7.1 | not-accessible | Extension table to tNetworkPolicyTable | |
| tNetworkPolicyExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.7.1.1 | not-accessible | ||
| TNE tNetworkPolicyType | 1.3.6.1.4.1.6527.6.2.2.2.1.7.1.1.1 | TNetworkPolicyType | read-create | Network policy Type determines the point of attachment of the network qos policy. Network policy with 'ipInterface' type can be attached to ip interface and 'port' type can be attached to physical port |
| TRE tNetworkPolicyRemarkPolicyId | 1.3.6.1.4.1.6527.6.2.2.2.1.7.1.1.2 | TRemarkPolicyID | read-create | Remark Policy Id that be used. |
| INT tNetworkIngressMeterColorMode | 1.3.6.1.4.1.6527.6.2.2.2.1.7.1.1.3 | INTEGER | read-create | tNetworkIngressMeterColorMode indicates whether the ip interface is color-aware or color-blind. By default every ip interface is color-aware |
| TMP tNetworkIngressMplsLspExpProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.7.1.1.4 | TMplsLspExpProfMapID | read-write | tNetworkIngressMplsLspExpProfile attaches the MPLS LSP EXP Profile to this network policy. |
| INT tNetworkEgressRemarkType | 1.3.6.1.4.1.6527.6.2.2.2.1.7.1.1.5 | INTEGER | read-create | This object specifies system remark type, tNetworkPolicyEgressRemark will be set to true and tNetworkEgressRemarkType will specify the remark type. |
| tNetworkQueueExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.7.2 | not-accessible | Extension table to tNetworkQueueTable | |
| tNetworkQueueExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.7.2.1 | not-accessible | ||
| TNA tNetworkQueuePolicyName | 1.3.6.1.4.1.6527.6.2.2.2.1.7.2.1.1 | TNamedItem | read-create | NetworkQueuePolicyName determines the queue management policy attached to this network queue. |
| INT tNetworkQueuePolicyQueueMode | 1.3.6.1.4.1.6527.6.2.2.2.1.7.2.1.2 | INTEGER | read-create | tNetworkQueuePolicyQueueMode specifies this policies mode. It has to be set when the policy is created. |
| INT tNetworkQueuePolicyWeight | 1.3.6.1.4.1.6527.6.2.2.2.1.7.2.1.3 | INTEGER | read-create | tNetworkQueuePolicyWeight specifies this policies weight. It is applicable only if queue mode is weighted. |
| tNetworkEgressFCExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.7.3 | not-accessible | Information about all network policies' egress FC traffic disposition, this table extends the capabilities available in tNetworkEgressFCTable | |
| tNetworkEgressFCExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.7.3.1 | not-accessible | Information about a particular network policy's egress per-forwarding-class traffic disposition. Entries are created/deleted as an action of creating/deleting a row in the tNetworkPolicyTable. There is no StorageType object, entries have a presumed StorageType of nonVolatile. | |
| DOT tNetworkEgressFCDot1pProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.7.3.1.1 | Dot1PPriority | read-write | the Dot1p to use for in-profile traffic. |
| tSASQueueMgmtObjects | 1.3.6.1.4.1.6527.6.2.2.2.1.8 | |||
| tQueueMgmtPolicyTable | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1 | not-accessible | Queue Management Policy definition for 7210-X platform. | |
| tQueueMgmtPolicyEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1 | not-accessible | ||
| TNA tQueueMgmtPolicyName | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.1 | TNamedItem | not-accessible | The value of tQueueMgmtPolicyName specifies the name of the Queue Management policy. |
| ROW tQueueMgmtPolicyRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.2 | RowStatus | read-create | Row Status of the entry. This allows creation/deletion of rows in this table. |
| TIM tQueueMgmtPolicyLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.3 | TimeStamp | read-only | Timestamp of last change to this row. |
| TIT tQueueMgmtPolicyDescription | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.4 | TItemDescription | read-create | User-provided description of the policy. |
| INT tQueueMgmtPolicyHiAdminStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.5 | INTEGER | read-create | tQueueMgmtPolicyHiAdminStatus specifies the admin state for the queue's high profile (Green Packets) slope. If the tQueueMgmtPolicyHiAdminStatus is set to 'down',the slope is inactive. |
| U32 tQueueMgmtPolicyHiStartAverage | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.6 | Unsigned32 | read-create | The percentage of the buffer utilized after which the drop probability starts to rise above 0. |
| U32 tQueueMgmtPolicyHiMaxAverage | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.7 | Unsigned32 | read-create | The percentage of the buffer utilized after which the drop probability is 100 percent. This implies that all packets beyond this point will be dropped. |
| U32 tQueueMgmtPolicyHiMaxProbability | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.8 | Unsigned32 | read-create | High Profile Max Probability.Defines the slope between the Start Average and Max Average |
| INT tQueueMgmtPolicyLoAdminStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.9 | INTEGER | read-create | tQueueMgmtPolicyLoAdminStatus specifies the admin state for the queue's low profile (Yellow Packets) slope. If the tQueueMgmtPolicyLoAdminStatus is set to 'down',the slope is inactive. |
| U32 tQueueMgmtPolicyLoStartAverage | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.10 | Unsigned32 | read-create | The percentage of the buffer utilized after which the drop probability starts to rise above 0. |
| U32 tQueueMgmtPolicyLoMaxAverage | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.11 | Unsigned32 | read-create | The percentage of the buffer utilized after which the drop probability is 100 percent. This implies that all packets beyond this point will be dropped. |
| U32 tQueueMgmtPolicyLoMaxProbability | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.12 | Unsigned32 | read-create | Low Profile Max Probability.Defines the slope between the Start Average and Max Average |
| INT tQueueMgmtPolicyCBS | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.13 | INTEGER | read-create | The amount of reserved buffer space (in kilo bytes) for the queue. |
| INT tQueueMgmtPolicyMBS | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.14 | INTEGER | read-create | The maximum amount of buffer space (in kilo bytes) allowed for the queue. |
| U32 tQueueMgmtPolicyTimeAvgFactor | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.15 | Unsigned32 | read-create | The time average factor describes the weighting between the previous shared buffer average utilization result and the new shared buffer utilization in determining the new shared buffer average utilization. |
| TIT tQueueMgmtPolicyScope | 1.3.6.1.4.1.6527.6.2.2.2.1.8.1.1.16 | TItemScope | read-create | Scope of the queue management policy. |
| tSASSapEgressObjects | 1.3.6.1.4.1.6527.6.2.2.2.1.9 | |||
| tSapEgressExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.9.1 | not-accessible | Extension table to tSapEgressTable | |
| tSapEgressExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.9.1.1 | not-accessible | ||
| T/F tSapEgressRemark | 1.3.6.1.4.1.6527.6.2.2.2.1.9.1.1.1 | TruthValue | read-create | This object specifies if the system will remark the egress packets on SAP or not. |
| TRE tSapEgressRemarkPolicyId | 1.3.6.1.4.1.6527.6.2.2.2.1.9.1.1.2 | TRemarkPolicyID | read-create | Remark Policy Id that be used. The default value is the default dot1p-dscp policy. |
| tSapEgressQueueExtnTable | 1.3.6.1.4.1.6527.6.2.2.2.1.9.2 | not-accessible | Extension table to tSapEgressQueueTable | |
| tSapEgressQueueExtnEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.9.2.1 | not-accessible | ||
| TNA tSapEgressQueuePolicyName | 1.3.6.1.4.1.6527.6.2.2.2.1.9.2.1.1 | TNamedItem | read-create | SapEgressQueuePolicyName determines the queue management policy attached to this SAP Egress queue. |
| INT tSapEgressQueuePolicyQueueMode | 1.3.6.1.4.1.6527.6.2.2.2.1.9.2.1.2 | INTEGER | read-create | tSapEgressQueuePolicyQueueMode specifies this policies mode. It has to be set when the policy is created. |
| INT tSapEgressQueuePolicyWeight | 1.3.6.1.4.1.6527.6.2.2.2.1.9.2.1.3 | INTEGER | read-create | tSapEgressQueuePolicyWeight specifies this policies weight. It is applicable only if queue mode is weighted. |
| tMplsQosObjects | 1.3.6.1.4.1.6527.6.2.2.2.1.10 | |||
| tMplsLspExpProfMapTable | 1.3.6.1.4.1.6527.6.2.2.2.1.10.1 | not-accessible | Information about all MPLS LSP EXP Profiles. | |
| tMplsLspExpProfMapEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.10.1.1 | not-accessible | Information about one MPLS LSP EXP Profile | |
| TMP tMplsLspExpProfMapIndex | 1.3.6.1.4.1.6527.6.2.2.2.1.10.1.1.1 | TMplsLspExpProfMapID | not-accessible | The tMplsLspExpProfMapIndex is used as index for the table. |
| ROW tMplsLspExpProfMapRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.10.1.1.2 | RowStatus | read-create | Row Status of this profile entry. |
| TIT tMplsLspExpProfMapDescription | 1.3.6.1.4.1.6527.6.2.2.2.1.10.1.1.3 | TItemDescription | read-create | User-provided description of the policy. |
| TIM tMplsLspExpProfMapLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.1.10.1.1.4 | TimeStamp | read-only | timestamp of last change to this row in tMplsLspExpProfMapTable. |
| TMP tGlobalMplsLspExpProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.10.3 | TMplsLspExpProfMapID | read-create | tGlobalMplsLspExpProfile is used by the LDP packets when the ip interface is configured in color aware mode. When the ip interface is configured in color blind mode, tGlobalMplsLspExpProfile is not applied to LDP packets received on that ip interface |
| tMplsLspExpProfileTable | 1.3.6.1.4.1.6527.6.2.2.2.1.10.4 | not-accessible | ||
| tMplsLspExpProfileEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.10.4.1 | not-accessible | Information about MPLS LSP EXP mapping. | |
| TMP tMplsLspExpProfileBits | 1.3.6.1.4.1.6527.6.2.2.2.1.10.4.1.1 | TMplsLspExpProfileValue | not-accessible | The MPLS Exp value to use for MPLS traffic. |
| ROW tMplsLspExpProfileRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.10.4.1.2 | RowStatus | read-create | Row Status of this profile entry. |
| TPR tMplsLspExpProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.10.4.1.3 | TProfile | read-create | tMplsLspExpProfile specifies the profile to be used for this EXP value as indicated by tMplsLspExpProfileBits. |
| TIM tMplsLspExpProfileLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.1.10.4.1.4 | TimeStamp | read-only | timestamp of last change to this row in tMplsLspExpProfileTable. |
| T/F tLdpLocalFcEnableAdminStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.10.5 | TruthValue | read-create | When tLdpLocalFcEnableAdminStatus is not set, the behavior is like SAS release 3.0 here the profile policy will be attached to one qos policy. tLdpLocalFcEnableAdminStatus when set to true the system opertation status .'tLdpLocalFcEnableOperStatus' will also become 'true', When tLdpLocalFcEnableAdminStatus is set then more than one profile policy can be attached to network policy When tLdpLocalFcEnableAdminStatus is reset to 'false', the system oper 'tLdpLocalFcEnableOperStatus' status would continue to be true until the system is reset.tLdpLocalFcEnableAdminStatus will take effect when the system is reset, |
| T/F tLdpLocalFcEnableOperStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.10.6 | TruthValue | read-only | Operational status of how ldp local fc is configured. After the system init, reseting tLdpLocalFcEnableAdminStatus to false from 'true' take effect when the system is reset |
| tSASGeneralQosObjects | 1.3.6.1.4.1.6527.6.2.2.2.1.21 | |||
| tSASRemarkPolicyTable | 1.3.6.1.4.1.6527.6.2.2.2.1.21.1 | not-accessible | ||
| tSASRemarkPolicyEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.21.1.1 | not-accessible | Information about a particular remarking policy's forwarding class mappings to dot1p / dscp / exp values. Entries are created/deleted by user. | |
| TRE tSASRemarkPolicyId | 1.3.6.1.4.1.6527.6.2.2.2.1.21.1.1.1 | TRemarkPolicyID | not-accessible | The remark policy ID is used as index for the table. |
| ROW tSASRemarkPolicyRowStatus | 1.3.6.1.4.1.6527.6.2.2.2.1.21.1.1.2 | RowStatus | read-create | Row Status. |
| TIT tSASRemarkPolicyDescription | 1.3.6.1.4.1.6527.6.2.2.2.1.21.1.1.3 | TItemDescription | read-create | User-provided description of the policy. |
| INT tSASRemarkPolicyType | 1.3.6.1.4.1.6527.6.2.2.2.1.21.1.1.4 | INTEGER | read-create | The remarking type of this policy. This specifies which of the fields will be remarked. |
| TIM tSASRemarkPolicyLastChanged | 1.3.6.1.4.1.6527.6.2.2.2.1.21.1.1.5 | TimeStamp | read-only | Timestamp of last change to this row in tSASRemarkPolicyTable. |
| tSASRemarkPolicyFCTable | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2 | not-accessible | ||
| tSASRemarkPolicyFCEntry | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1 | not-accessible | Information about a particular queue in a remarking policy's forwarding class mappings to dot1p / dscp / exp values. Entries are created/deleted whenever a policy is created/deleted. | |
| TFC tSASRemarkPolicyFCName | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.1 | TFCName | not-accessible | The FC Class Name. |
| DOT tSASRemarkPolicyDot1PInProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.2 | Dot1PPriority | read-write | The Dot1p to use for in-profile traffic. This field is valid only for the following remarking types: dot1p dot1p-dscp |
| DOT tSASRemarkPolicyDot1POutProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.3 | Dot1PPriority | read-write | The Dot1p to use for out-of-profile traffic. This field is valid only for the following remarking types: dot1p dot1p-dscp |
| TDS tSASRemarkPolicyDSCPInProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.4 | TDSCPNameOrEmpty | read-write | The DSCP to use for in-profile traffic. This field is valid only for remarking type of dscp and dot1p-dscp. |
| TDS tSASRemarkPolicyDSCPOutProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.5 | TDSCPNameOrEmpty | read-write | The DSCP to use for out-of-profile traffic. This field is valid only for remarking type of dscp and dot1p-dscp. |
| TLS tSASRemarkPolicyLspExpInProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.6 | TLspExpValue | read-write | The lsp-exp value to use for in-profile traffic. This field is valid only for remarking type of lsp-exp. |
| TLS tSASRemarkPolicyLspExpOutProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.7 | TLspExpValue | read-write | The lsp-exp value to use for out-of-profile traffic. This field is valid only for remarking type of lsp-exp. |
| TDO tSASRemarkPolicyDot1PLspExpInProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.8 | TDot1PLspExpValue | read-write | The Dot1p / MPLS Exp value to use for in-profile traffic. This field is valid only for remarking type of dot1p-lsp-exp-shared. |
| TDO tSASRemarkPolicyDot1PLspExpOutProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.9 | TDot1PLspExpValue | read-write | The Dot1p / MPLS Exp value to use for out-profile traffic. This field is valid only for remarking type of dot1p-lsp-exp-shared. |
| DOT tSASRemarkPolicyDot1PProfile | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.10 | Dot1PPriority | read-write | The Dot1p to use for profile traffic. |
| TDE tSASRemarkPolicyForceDEValue | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.11 | TDEValue | read-write | The value of tSASRemarkPolicyForceDEValue specifies the DE value to set for remark packets in this forwarding class regardless of profile status of the frames. An inconsistentValue error is returned if this object is set to any value other than '-1', when tSASRemarkFCDEMark object is set to 'false'. |
| T/F tSASRemarkPolicyFCDEMark | 1.3.6.1.4.1.6527.6.2.2.2.1.21.2.1.12 | TruthValue | read-write | The value of tSASRemarkPolicyFCDEMark specifies whether to set DE value in the frames of this forwarding class. An inconsistentValue error is returned if this object is set to 'false' when tSASRemarkPolicyFCForceDEValue object is not set to '-1'. |
FAQ
How would TIMETRA-SAS-QOS-MIB help verify QoS on an Alcatel-Lucent/Nokia 7x50 SAS switch?
It exposes the MPLS EXP-bit profile mapping table (tMplsLspExpProfMapTable) and EXP profile definitions (tMplsLspExpProfileTable) used to classify and schedule traffic at the network access edge. An operator can poll these tables to confirm the EXP-to-QoS mapping matches the intended provisioning, since a misconfigured mapping would give traffic the wrong forwarding treatment.
Does TIMETRA-SAS-QOS-MIB report hardware faults like temperature or power?
No — its monitoring value is around configuration/software state: verifying QoS profile mappings and row status and tracking last-configuration-change timestamps, not physical sensor data; hardware health is covered by other MIBs in the TIMETRA family.
RFC description
Alcatel-Lucent 7x50 SAS quality-of-service configuration and statistics management.
Start monitoring Nokia/Alcatel-Lucent 7210 SAS service access switch product line, entire range (MPLS EXP-to-QoS profile mapping status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.