All MIBs › SWL2MGMT-MIB
Organization: enterprise, Inc.
Last Updated: 2000-07-15
Category: Switch Management - D-Link
Description: Manages Layer 2 switch functions including MAC learning, VLANs, and spanning tree per D-Link platforms.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is SWL2MGMT-MIB?
SWL2MGMT-MIB is a D-Link proprietary module defining Layer 2 network management structure for D-Link switch platforms, covering MAC address learning, VLAN configuration, and spanning tree operation. It exposes configuration data (VLAN membership, spanning tree parameters) as well as status data (learned MAC/forwarding-database entries, spanning tree port states). This lets an administrator monitor the software/hardware-level health of the switching fabric, since a spanning tree port stuck in a blocking or discarding state indicates a topology change or loop, and forwarding-database growth indicates how actively the switch is learning addresses. It builds on the concepts of the standard BRIDGE-MIB and Q-BRIDGE-MIB (IEEE 802.1D/802.1Q) as a proprietary parallel implementation for D-Link hardware. It is deployed on D-Link managed Layer 2 Ethernet switches in small-to-midsize enterprise LANs. Engineers can download the SWL2MGMT-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in SWL2MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- D-Link managed Layer 2 Ethernet switches
Monitoring Examples
No sample objects were provided for this module, so specific object names cannot be cited with confidence. Based on the description, it would plausibly expose a MAC address/forwarding-database table and a spanning-tree port-state table; an administrator would poll per-port spanning tree state to detect a port stuck in a blocking or discarding state, indicating a network loop or recent topology change.
What Can Be Monitored
- MAC address/forwarding-database entries
- VLAN membership configuration
- spanning tree port state
- Layer 2 forwarding status
This MIB depends on
Related MIBs
Imported Objects
From RFC-1215
| TRAP-TYPE |
From RFC1213-MIB
| DisplayString |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Gauge32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| MacAddress | |
| RowStatus | |
| TruthValue |
From SWPRIMGMT-MIB
| privateMgmt | OBJECT-IDENTITY |
How to Use in IPNetwork Monitor
Example using swL2PortUtilTxSec OID:
Select a D-Link managed Layer 2 Ethernet switch (MAC learning/VLAN/spanning-tree status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type swL2PortUtilTxSec into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Indicates how many packets transmitted per second. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Gauge32-type OID, Value bounds is the most useful condition here — trigger an alert if the value drifts significantly from its normal baseline, since an unexpected change often points to a real underlying issue. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| swL2MgmtMIB | 1.3.6.1.4.1.2272.1.201.1.2 | The Structure of Layer 2 Network Management Information for the proprietary enterprise. | ||
| NTF managementPortLinkUp | 1.3.6.1.4.1.2272.1.201.1.2.0.1 | The trap is sent whenever the management port is link up. | ||
| NTF managementPortLinkDown | 1.3.6.1.4.1.2272.1.201.1.2.0.2 | The trap is sent whenever the management port is link down. | ||
| swL2DevMgmt | 1.3.6.1.4.1.2272.1.201.1.2.1 | |||
| swL2DevInfo | 1.3.6.1.4.1.2272.1.201.1.2.1.1 | |||
| TIK swDevInfoSystemUpTime | 1.3.6.1.4.1.2272.1.201.1.2.1.1.1 | TimeTicks | read-only | The value of sysUpTime at the time the switch entered its current operational state. If the current state was entered prior to the last re-initialization, then this object contains a zero value. This value is in units of seconds. |
| INT swDevInfoTotalNumOfPort | 1.3.6.1.4.1.2272.1.201.1.2.1.1.2 | INTEGER | read-only | The number of ports within this switch. This value is the sum of the ports within this switch. |
| INT swDevInfoNumOfPortInUse | 1.3.6.1.4.1.2272.1.201.1.2.1.1.3 | INTEGER | read-only | The number of ports in this switch connected to the segment or the end stations. |
| INT swDevInfoConsoleInUse | 1.3.6.1.4.1.2272.1.201.1.2.1.1.4 | INTEGER | read-only | This usage indication of console system. |
| OCT swDevInfoFrontPanelLedStatus | 1.3.6.1.4.1.2272.1.201.1.2.1.1.5 | OCTET STRING | read-only | This object is a set of system LED indications. The first three octets is defined as system LED. The first LED is primary power LED. The second LED is redundant power LED. The third LED is console LED. The other octets following the second octets are the logical port LED (following dot1dBasePort ordering). Every two bytes are presented to a port. The first byte is presentd to the Link/Activity LED. The second byte is presented to the Speed LED. Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0. |
| INT swL2DevCtrlUpDownloadState | 1.3.6.1.4.1.2272.1.201.1.2.1.1.6 | INTEGER | read-only | status of upload/download control. If the value is 'other', means never firmware updated since device started up. |
| INT swDevInfoSaveCfg | 1.3.6.1.4.1.2272.1.201.1.2.1.1.7 | INTEGER | read-only | This object indicates the status of the device configuration. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. proceeding(2) - the device configuration is saving into the NV-RAM. ready(3) �V the device configuration has been ready to save into NV-RAM. failed(4) - The processing of saving device configuration is failed. |
| swL2DevCtrl | 1.3.6.1.4.1.2272.1.201.1.2.1.2 | |||
| INT swL2DevCtrlStpState | 1.3.6.1.4.1.2272.1.201.1.2.1.2.1 | INTEGER | read-write | This object can be enabled or disabled spanning tree algorithm during runtime of the system. |
| INT swL2DevCtrlIGMPSnooping | 1.3.6.1.4.1.2272.1.201.1.2.1.2.2 | INTEGER | read-write | This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled. |
| INT swL2DevCtrlRmonState | 1.3.6.1.4.1.2272.1.201.1.2.1.2.3 | INTEGER | read-write | This object can be enabled or disabled RMON. |
| STR swL2DevCtrlUpDownloadImageFileName | 1.3.6.1.4.1.2272.1.201.1.2.1.2.4 | DisplayString | read-write | The name of the image file to be uploaded/Downloaded from the device to TFTP server when enabling image upload/download function (by writing swL2DevCtrlUpDownloadImage). |
| IP swL2DevCtrlUpDownloadImageSourceAddr | 1.3.6.1.4.1.2272.1.201.1.2.1.2.5 | IpAddress | read-write | The ip address where been uploaded/Downloaded image file. |
| INT swL2DevCtrlUpDownloadImage | 1.3.6.1.4.1.2272.1.201.1.2.1.2.6 | INTEGER | read-write | Image file upload/download control. After setting, it will immediately invoke image upload/download function. While retrieving the value of this object, it always returns 'other' normally. |
| INT swL2DevCtrlSaveCfg | 1.3.6.1.4.1.2272.1.201.1.2.1.2.7 | INTEGER | read-write | As the object is set to active, the current device configuration is save into to NV-RAM.If set to normal, do nothing. |
| INT swL2DevCtrlCleanAllStatisticCounter | 1.3.6.1.4.1.2272.1.201.1.2.1.2.8 | INTEGER | read-write | As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing. |
| INT swL2DevCtrlStpForwardBPDU | 1.3.6.1.4.1.2272.1.201.1.2.1.2.9 | INTEGER | read-write | This object allow the forwarding of STP BPDU packets from other network device or not when STP is disabled on the device. |
| swL2DevAlarm | 1.3.6.1.4.1.2272.1.201.1.2.1.3 | |||
| INT swL2DevAlarmNewRoot | 1.3.6.1.4.1.2272.1.201.1.2.1.3.1 | INTEGER | read-write | When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap. |
| INT swL2DevAlarmTopologyChange | 1.3.6.1.4.1.2272.1.201.1.2.1.3.2 | INTEGER | read-write | This object determine to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other. |
| INT swL2DevAlarmLinkChange | 1.3.6.1.4.1.2272.1.201.1.2.1.3.3 | INTEGER | read-write | This object determine to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other. |
| swL2UnitMgmt | 1.3.6.1.4.1.2272.1.201.1.2.2 | |||
| swL2UnitCtrl | 1.3.6.1.4.1.2272.1.201.1.2.2.1 | |||
| swL2ModuleMgmt | 1.3.6.1.4.1.2272.1.201.1.2.3 | |||
| swL2PortMgmt | 1.3.6.1.4.1.2272.1.201.1.2.4 | |||
| swL2PortInfoTable | 1.3.6.1.4.1.2272.1.201.1.2.4.1 | not-accessible | A table that contains information about every port. | |
| swL2PortInfoEntry | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1 | not-accessible | A list of information for each port of the device. | |
| INT swL2PortInfoPortIndex | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.1 | INTEGER | read-only | This object indicates the module's port number.(1..Max port number in the module) |
| INT swL2PortInfoUnitIndex | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.2 | INTEGER | read-only | Indicates ID of the unit in the device |
| INT swL2PortInfoType | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.3 | INTEGER | read-only | This object indicates the connector type of this port. |
| INT swL2PortInfoLinkStatus | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.4 | INTEGER | read-only | This object indicates the port link status. |
| INT swL2PortInfoNwayStatus | 1.3.6.1.4.1.2272.1.201.1.2.4.1.1.5 | INTEGER | read-only | This object indicates the port speed and duplex mode. |
| swL2PortCtrlTable | 1.3.6.1.4.1.2272.1.201.1.2.4.2 | not-accessible | A table that contains control information about every port. | |
| swL2PortCtrlEntry | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1 | not-accessible | A list of control information for each port of the device. | |
| INT swL2PortCtrlPortIndex | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.1 | INTEGER | read-only | This object indicates the module's port number.(1..Max port number in the module) |
| INT swL2PortCtrlUnitIndex | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.2 | INTEGER | read-only | Indicates ID of the unit in the device |
| INT swL2PortCtrlAdminState | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.3 | INTEGER | read-write | This object decide the port enabled or disabled. |
| INT swL2PortCtrlNwayState | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.4 | INTEGER | read-write | Chose the port speed, duplex mode, and N-Way function mode. |
| INT swL2PortCtrlFlowCtrlState | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.5 | INTEGER | read-write | The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames. |
| INT swL2PortCtrlAddressLearningState | 1.3.6.1.4.1.2272.1.201.1.2.4.2.1.6 | INTEGER | read-write | This object decide the address learning state on this port is enabled or disabled. |
| swL2PortUtilTable | 1.3.6.1.4.1.2272.1.201.1.2.4.3 | not-accessible | A table that contains information of utilization about every port. | |
| swL2PortUtilEntry | 1.3.6.1.4.1.2272.1.201.1.2.4.3.1 | not-accessible | A list of information of utilization for each port of the device. | |
| INT swL2PortUtilPortIndex | 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.1 | INTEGER | read-only | This object indicates the module's port number.(1..Max port number in the module) |
| G32 swL2PortUtilTxSecEx | 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.2 | Gauge32 | read-only | Indicates how many packets transmitted per second. |
| G32 swL2PortUtilRxSec | 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.3 | Gauge32 | read-only | Indicates how many packets received per second. |
| INT swL2PortUtilUtilization | 1.3.6.1.4.1.2272.1.201.1.2.4.3.1.4 | INTEGER | read-only | This object indicates the port utilization. |
| swL2FilterMgmt | 1.3.6.1.4.1.2272.1.201.1.2.6 | |||
| swL2FilterAddrConfig | 1.3.6.1.4.1.2272.1.201.1.2.6.1 | |||
| INT swL2FilterAddrMaxSupportedEntries | 1.3.6.1.4.1.2272.1.201.1.2.6.1.1 | INTEGER | read-only | Maximum number of entries in the MAC address filtering table (swL2FilterAddrCtrlTable). |
| INT swL2FilterAddrCurrentTotalEntries | 1.3.6.1.4.1.2272.1.201.1.2.6.1.2 | INTEGER | read-only | Current applied number of entries in the MAC address filtering table. |
| swL2FilterAddrCtrlTable | 1.3.6.1.4.1.2272.1.201.1.2.6.1.3 | not-accessible | This table defines information for the device to filter packets with specific MAC address (either as the DA and/or as the SA). The MAC address can be a unicast address or a multicast address. This table has higher priority than both static FDB table and IGMP table. It means that if a MAC address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet. | |
| swL2FilterAddrCtrlEntry | 1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1 | not-accessible | A list of information about a specific unicast/multicast MAC address for which the switch has filtering information. | |
| MAC swL2FilterAddrMacIndex | 1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1.1 | MacAddress | read-only | This object indicates a unicast/multicast MAC address for which the switch has filtering information. But if the swL2FilterAddrState = src-addr then the object can not be a multicast MAC address. |
| INT swL2FilterAddrState | 1.3.6.1.4.1.2272.1.201.1.2.6.1.3.1.2 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. dst-addr(2) - recieved frames's destination address are currently used to be filtered as it meets with the MAC address entry of the table. src-addr(3) - recieved frames's source address are currently used to be filtered as it meets with the MAC address entry of the table. dst-src-addr(4) - recieved frames's destination address or source address are currently used to be filtered as it meets with the MAC address entry of the table. invalid(5) - writing this value to the object, and then the corresponding entry will be removed from the table. |
| swL2VlanMgmt | 1.3.6.1.4.1.2272.1.201.1.2.7 | |||
| swL2StaticVlanTable | 1.3.6.1.4.1.2272.1.201.1.2.7.1 | not-accessible | A table containing static configuration information for each VLAN configured into the device by (local or network) management. | |
| swL2StaticVlanEntry | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1 | not-accessible | Static information for a VLAN configured into the device by (local or network) management. | |
| INT swL2StaticVlanIndex | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.1 | INTEGER | read-only | A value that uniquely identifies the Virtual LAN associated with this entry. |
| STR swL2StaticVlanName | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.2 | DisplayString | read-write | An administratively-assigned name for this VLAN. |
| INT swL2StaticVlanType | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.3 | INTEGER | read-write | The type of VLAN, distinguished according to the policy used to define its port membership. |
| INT swL2StaticVlanProtocolId | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.4 | INTEGER | read-write | The protocol identifier of this VLAN. This value is meaningful only if swL2StaticVlanType is equal to byProtocolId(3). For other VLAN types it should have the value none(0). |
| IP swL2StaticVlanIpSubnetAddr | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.5 | IpAddress | read-write | The IP subnet address of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0. |
| IP swL2StaticVlanIpSubnetMask | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.6 | IpAddress | read-write | The IP subnet mask of this VLAN. This value is meaningful only if rcVlanType is equal to byIpSubnet(2). For other VLAN types it should have the value 0.0.0.0. |
| OCT swL2StaticVlanUserDefinedPid | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.7 | OCTET STRING | read-write | When swL2StaticVlanProtocolId is set to userDefined(16) in a protocol-based VLAN, this field represents the 16-bit user defined protocol identifier. Otherwise, this object should be zero. |
| INT swL2StaticVlanEncap | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.8 | INTEGER | read-write | This value is meaningful only if swL2StaticVlanProtocolId is set to userDefined(16). Otherwise, this object should be un-used(5). If If this set to ethernet2(2), the Detagged Frame uses Type-encapsulated 802.3 format. If this set to llc(3), the Detagged Frame contains both a DSAP and an SSAP address field in the positions. If this set to snap(4), the Detagged Frame is of the format specified by IEEE Std. 802.1H for the encoding of an IEEE 802.3 Type Field in an 802.2/SNAP header. |
| INT swL2StaticVlanUserPriority | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.9 | INTEGER | read-write | User priority level. This value is meaningful only if swL2StaticVlanType is set to byIpSubnet(2) or byProtocolId(3). |
| POR swL2StaticVlanEgressPorts | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.10 | PortList | read-write | The set of ports which are permanently assigned to the egress list for this VLAN by management. The default value of this object is a string of zeros of appropriate length. |
| POR swL2StaticVlanUntaggedPorts | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.11 | PortList | read-write | The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN is a string of appropriate length including all ports. There is no specified default for other VLANs. |
| ROW swL2StaticVlanStatus | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.12 | RowStatus | read-write | This object indicates the status of this entry. |
| INT swL2StaticVlanIpSubnetArpClassId | 1.3.6.1.4.1.2272.1.201.1.2.7.1.1.13 | INTEGER | read-write | This object indicates the ARP classification ID. If the swL2StaticVlanType is not byIpSubnet(2), this value must be 0. If the swL2StaticVlanType is byIpSubnet(2), the range of this object is 1 to 4094. This object is useful when create the first IpSubnet entry, and not allow to modify. |
| swL2VlanPortTable | 1.3.6.1.4.1.2272.1.201.1.2.7.2 | not-accessible | A table containing per port control and status information for VLAN configuration in the device. | |
| swL2VlanPortEntry | 1.3.6.1.4.1.2272.1.201.1.2.7.2.1 | not-accessible | Information controlling VLAN configuration for a port on the device. | |
| INT swL2VlanPortIndex | 1.3.6.1.4.1.2272.1.201.1.2.7.2.1.1 | INTEGER | read-only | An unique index used to identify a particular port in the system. |
| INT swL2VlanPortPvid | 1.3.6.1.4.1.2272.1.201.1.2.7.2.1.2 | INTEGER | read-only | The PVID, the VLAN ID assigned to untagged frames or Priority- Tagged frames received on this port. |
| INT swL2VlanPortIngressChecking | 1.3.6.1.4.1.2272.1.201.1.2.7.2.1.3 | INTEGER | read-write | When this is enabled(3) the device will discard incoming frames for VLANs which do not include this Port in its Member set. When disabled(2), the port will accept all incoming frames. |
| swL2TrunkMgmt | 1.3.6.1.4.1.2272.1.201.1.2.8 | |||
| INT swL2TrunkMaxSupportedEntries | 1.3.6.1.4.1.2272.1.201.1.2.8.1 | INTEGER | read-only | Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable). |
| INT swL2TrunkCurrentNumEntries | 1.3.6.1.4.1.2272.1.201.1.2.8.2 | INTEGER | read-only | Current actived number of entries in the trunk configuration table. |
| swL2TrunkCtrlTable | 1.3.6.1.4.1.2272.1.201.1.2.8.3 | not-accessible | This table specifys which ports group a set of ports(up to 8) into a single logical link. | |
| swL2TrunkCtrlEntry | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1 | not-accessible | A list of information specifies which ports group a set of ports(up to 8) into a single logical link. | |
| INT swL2TrunkIndex | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.1 | INTEGER | read-only | The index of logical port trunk. The trunk group number depend on the existence of unit and module. |
| STR swL2TrunkName | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.2 | DisplayString | read-write | The name of logical port trunk. |
| INT swL2TrunkMasterPort | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.3 | INTEGER | read-write | The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on). |
| POR swL2TrunkMember | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.4 | PortList | read-write | Indicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 4 for one trunks. |
| INT swL2TrunkFloodingPort | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.5 | INTEGER | read-only | The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port. |
| INT swL2TrunkState | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.6 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the port trunk disabled. enabled(3) - the port trunk enabled. invalid(4) - writing this value to the object, and then the corresponding entry will be removed from the table. |
| INT swL2TrunkBPDU8600InterState | 1.3.6.1.4.1.2272.1.201.1.2.8.3.1.7 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the trunk member doesn't send BPDU. enabled(3) - the trunk member can send BPDU. |
| INT swL2TrunkAlgorithm | 1.3.6.1.4.1.2272.1.201.1.2.8.4 | INTEGER | read-write | This object configures to part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data. This feature is only available using the address-based load-sharing algorithm. |
| swL2MirrorMgmt | 1.3.6.1.4.1.2272.1.201.1.2.9 | |||
| INT swL2MirrorLogicTargetPort | 1.3.6.1.4.1.2272.1.201.1.2.9.1 | INTEGER | read-write | This object indicates switch which port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to bridge MIB, etc. |
| POR swL2MirrorPortSourceIngress | 1.3.6.1.4.1.2272.1.201.1.2.9.2 | PortList | read-write | The represent the ingress into the source port packet to sniffed. |
| POR swL2MirrorPortSourceEgress | 1.3.6.1.4.1.2272.1.201.1.2.9.3 | PortList | read-write | The represent the egress from the source port packet to sniffed. |
| INT swL2MirrorPortState | 1.3.6.1.4.1.2272.1.201.1.2.9.4 | INTEGER | read-write | This object indicates the port mirroring state. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - writing this value to the object, and then the corresponding entry will be removed from the table. enabled(3) - this entry is reside in the table. |
| swL2IGMPMgmt | 1.3.6.1.4.1.2272.1.201.1.2.10 | |||
| INT swL2IGMPMaxSupportedVlans | 1.3.6.1.4.1.2272.1.201.1.2.10.1 | INTEGER | read-only | Maximum number of Vlans in the layer 2 IGMP control table (swL2IGMPCtrlTable). |
| INT swL2IGMPMaxIpGroupNumPerVlan | 1.3.6.1.4.1.2272.1.201.1.2.10.2 | INTEGER | read-only | Maximum number of multicast ip group per Vlan in the layer 2 IGMP information table (swL2IGMPQueryInfoTable). |
| swL2IGMPCtrlTable | 1.3.6.1.4.1.2272.1.201.1.2.10.3 | not-accessible | The table controls the Vlan's IGMP function. Its scale depends on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled mode, there is only one entry in the table, with index 1. If VLAN is in Port-Base or 802.1q mode, the number of entries can be up to 12, with index range from 1 to 12. | |
| swL2IGMPCtrlEntry | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1 | not-accessible | The entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP capture switch (swL2DevCtrlIGMPSnooping) is enabled. | |
| INT swL2IGMPCtrlVid | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.1 | INTEGER | read-only | This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the Vid setting can vary from 1 to 4094 by management user, and the Vid in each entry must be unique in the IGMP Control Table. |
| INT swL2IGMPQueryInterval | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.2 | INTEGER | read-write | The frequency at which IGMP Host-Query packets are transmitted on this switch. |
| INT swL2IGMPMaxResponseTime | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.3 | INTEGER | read-write | The maximum query response time on this switch. |
| INT swL2IGMPRobustness | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.4 | INTEGER | read-write | The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses. |
| INT swL2IGMPLastMemberQueryInterval | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.5 | INTEGER | read-write | The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages. |
| INT swL2IGMPHostTimeout | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.6 | INTEGER | read-write | The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please reference RFC2236-1997. |
| INT swL2IGMPRouteTimeout | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.7 | INTEGER | read-write | The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages. |
| INT swL2IGMPLeaveTimer | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.8 | INTEGER | read-write | When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left. |
| INT swL2IGMPQueryState | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.9 | INTEGER | read-write | This object decide the IGMP query enabled or disabled. |
| INT swL2IGMPCurrentState | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.10 | INTEGER | read-only | This object indicates the current IGMP query state. |
| INT swL2IGMPCtrlState | 1.3.6.1.4.1.2272.1.201.1.2.10.3.1.11 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - IGMP funtion is disabled for this entry. enabled(3) - IGMP funtion is enabled for this entry. |
| swL2IGMPQueryInfoTable | 1.3.6.1.4.1.2272.1.201.1.2.10.4 | not-accessible | The table contains the number current IGMP query packets which is captured by this device, as well as the IGMP query packets sent by the device. | |
| swL2IGMPQueryInfoEntry | 1.3.6.1.4.1.2272.1.201.1.2.10.4.1 | not-accessible | Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled. | |
| INT swL2IGMPInfoVid | 1.3.6.1.4.1.2272.1.201.1.2.10.4.1.1 | INTEGER | read-only | This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable). |
| INT swL2IGMPInfoQueryCount | 1.3.6.1.4.1.2272.1.201.1.2.10.4.1.2 | INTEGER | read-only | This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis. |
| INT swL2IGMPInfoTxQueryCount | 1.3.6.1.4.1.2272.1.201.1.2.10.4.1.3 | INTEGER | read-only | This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1. |
| swL2IGMPGroupTable | 1.3.6.1.4.1.2272.1.201.1.2.10.5 | not-accessible | The table containing current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also. | |
| swL2IGMPGroupEntry | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1 | not-accessible | Information about current IGMP information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. | |
| INT swL2IGMPVid | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.1 | INTEGER | read-only | This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network. |
| IP swL2IGMPGroupIpAddr | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.2 | IpAddress | read-only | This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis. |
| MAC swL2IGMPMacAddr | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.3 | MacAddress | read-only | This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis. |
| POR swL2IGMPPortMap | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.4 | PortList | read-only | This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero. |
| INT swL2IGMPIpGroupReportCount | 1.3.6.1.4.1.2272.1.201.1.2.10.5.1.5 | INTEGER | read-only | This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis. |
| swL2IGMPForwardTable | 1.3.6.1.4.1.2272.1.201.1.2.10.6 | not-accessible | The table containing current IGMP forwarding information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. See swL2FilterMgmt description also. | |
| swL2IGMPForwardEntry | 1.3.6.1.4.1.2272.1.201.1.2.10.6.1 | not-accessible | Information about current IGMP forwarding information which captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. | |
| INT swL2IGMPForwardVid | 1.3.6.1.4.1.2272.1.201.1.2.10.6.1.1 | INTEGER | read-only | This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report forward information captured on network. |
| IP swL2IGMPForwardGroupIpAddr | 1.3.6.1.4.1.2272.1.201.1.2.10.6.1.2 | IpAddress | read-only | This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis. |
| POR swL2IGMPForwardPortMap | 1.3.6.1.4.1.2272.1.201.1.2.10.6.1.3 | PortList | read-only | This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'(Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets is represent one unit port according its logic port. If the unit less 32 port, the other port don't care just fill zero. |
| swL2IGMPRPTable | 1.3.6.1.4.1.2272.1.201.1.2.10.7 | not-accessible | The table allows you to designate a range of ports as being connected to multicast-enabled routers. This will ensure that all packets with such a router as its destination will reach the multicast-enabled router, regardless of protocol, etc. | |
| swL2IGMPRPEntry | 1.3.6.1.4.1.2272.1.201.1.2.10.7.1 | not-accessible | A list of swL2IGMPRPTable. | |
| INT swL2IGMPRPVid | 1.3.6.1.4.1.2272.1.201.1.2.10.7.1.1 | INTEGER | read-only | The Vid of the VLAN on which the router port resides. |
| POR swL2IGMPRPStaticRouterPort | 1.3.6.1.4.1.2272.1.201.1.2.10.7.1.2 | PortList | read-write | Specifies a range of ports which will be configured as router ports. |
| POR swL2IGMPRPDynamicRouterPort | 1.3.6.1.4.1.2272.1.201.1.2.10.7.1.3 | PortList | read-only | Displays router ports that have been dynamically configued. |
| INT swL2IGMPMulticastRouterOnly | 1.3.6.1.4.1.2272.1.201.1.2.10.8 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the switch forwards all mulitcast traffic to any IP router. enabled(3) - the switch will forward all multicast traffic to the multicast router, only. |
| swL2IGMPGroupPortTable | 1.3.6.1.4.1.2272.1.201.1.2.10.9 | not-accessible | This table describe the detail information of the member ports of the swL2IGMPGroupTable. | |
| swL2IGMPGroupPortEntry | 1.3.6.1.4.1.2272.1.201.1.2.10.9.1 | not-accessible | Information about member ports of current swL2IGMPGroupTable. | |
| INT swL2IGMPPortMember | 1.3.6.1.4.1.2272.1.201.1.2.10.9.1.1 | INTEGER | read-only | This object indicates which ports are belong to the same multicast group, in per-Vlan basis, in swL2IGMPGroupTable. |
| INT swL2IGMPPortAgingTime | 1.3.6.1.4.1.2272.1.201.1.2.10.9.1.2 | INTEGER | read-only | This object indicate the aging out timer. This value is in units of seconds. |
| INT swL2IGMPMulticastFilter | 1.3.6.1.4.1.2272.1.201.1.2.10.10 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - the un-registered multicast traffic will be flooded. enabled(3) - the un-registered multicast traffic will be filtered. |
| swL2TrafficMgmt | 1.3.6.1.4.1.2272.1.201.1.2.12 | |||
| swL2TrafficCtrlTable | 1.3.6.1.4.1.2272.1.201.1.2.12.1 | not-accessible | This table specifys the storm traffic control configuration. | |
| swL2TrafficCtrlEntry | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1 | not-accessible | A list of information specifies the storm traffic control configuration. | |
| INT swL2TrafficCtrlGroupIndex | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.1 | INTEGER | read-only | The index of logical port trunk. The trunk group number depend on the existence of unit and module. |
| INT swL2TrafficCtrlUnitIndex | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.2 | INTEGER | read-only | Indicates ID of the unit in the device |
| INT swL2TrafficCtrlBMStormthreshold | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.3 | INTEGER | read-write | This object to decide how much thousand packets per second broadcast/multicast (depend on swL2TrafficCtrlBcastStormCtrl, swL2TrafficCtrlMcastStormCtrl or swL2TrafficCtrlDlfStormCtrl objects whether is enabled) will active storm control. Whenever a port reaches its configured amount of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet. |
| INT swL2TrafficCtrlBcastStormCtrl | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.4 | INTEGER | read-write | This object indicates broadcast storm control function is enabled or disabled. |
| INT swL2TrafficCtrlMcastStormCtrl | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.5 | INTEGER | read-write | This object indicates multicast storm control function is enabled or disabled. |
| INT swL2TrafficCtrlDlfStormCtrl | 1.3.6.1.4.1.2272.1.201.1.2.12.1.1.6 | INTEGER | read-write | This object indicates destination lookup fail function is enabled or disabled. |
| swL2QosMgmt | 1.3.6.1.4.1.2272.1.201.1.2.13 | |||
| swL2QosSchedulingTable | 1.3.6.1.4.1.2272.1.201.1.2.13.1 | not-accessible | The switch contains 4 hardware priority queues. Incoming packets must be mapped to one of these four queues. Each hardware queue will transmit all of the packets in its buffer before allowing the next lower priority queue to transmit its packets. When the lowest hardware priority queue has finished transmitting all of its packets, the highest hardware priority queue can again transmit any packets it may have received. | |
| swL2QosSchedulingEntry | 1.3.6.1.4.1.2272.1.201.1.2.13.1.1 | not-accessible | A list of information specifies the Qos output scheduling Table. | |
| INT swL2QosSchedulingClassId | 1.3.6.1.4.1.2272.1.201.1.2.13.1.1.1 | INTEGER | read-only | This specifies which of the four hardware priority queues. The four hardware priority queues are identified by number, from 0 to 3, with the 0 queue being the lowest priority. |
| INT swL2QosSchedulingMaxPkts | 1.3.6.1.4.1.2272.1.201.1.2.13.1.1.2 | INTEGER | read-write | Specifies the maximium number of packets the above specified hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. |
| INT swL2QosSchedulingMaxLatency | 1.3.6.1.4.1.2272.1.201.1.2.13.1.1.3 | INTEGER | read-write | Specifies the maximum amount of time the above specified hardware priority queue will be allowed to transmit packets before allowing the next lowest hardware priority queue to begin transmitting its packets. A value between 0 and 255 can be specified. With this value multiplied by 16 ms to arrive at the total allowed time for the queue to transmit packets. |
| swL2QosPriorityTable | 1.3.6.1.4.1.2272.1.201.1.2.13.2 | not-accessible | This table display the current priority settings on the switch. | |
| swL2QosPriorityEntry | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1 | not-accessible | A list of information display the current priority settings on the switch. | |
| INT swL2QosPriorityType | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.1 | INTEGER | read-only | These parameters define what characteristics an incoming packet must meet. One or more of the above parameters must be defined. |
| OCT swL2QosPriorityValue | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.2 | OCTET STRING | read-only | This object must match with swL2QosPriorityType. If the type is type-dscp(2), the range of this object is 0~63. If the type is type-8021p(3), the range of this object is 0~7. If the type is type-tcp(4) or type-udp(5), the range of this object is 1~65535. |
| INT swL2QosPriorityPriority | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.3 | INTEGER | read-write | Allows to specify a priority value to be written to the 802.1p priority field of an incoming packet that meets the criteria. |
| INT swL2QosPriorityPriorityState | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.4 | INTEGER | read-write | This object indicates 802.1p priority function is enabled or disabled. |
| INT swL2QosPriorityReplaceDscp | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.5 | INTEGER | read-write | Allows to specify a value to be written to the DSCP field of an incoming packet that meets the criteria. |
| INT swL2QosPriorityReplaceDscpState | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.6 | INTEGER | read-write | This object indicates DSCP function is enabled or disabled. |
| INT swL2QosPriorityReplacePriority | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.7 | INTEGER | read-write | This object indicates the 802.1p user priority with the priority specified above will be replaced or not. |
| INT swL2QosPriorityState | 1.3.6.1.4.1.2272.1.201.1.2.13.2.1.8 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| swL2MgmtMIBTraps | 1.3.6.1.4.1.2272.1.201.1.2.14 | |||
| swL2StormCtrlMgmt | 1.3.6.1.4.1.2272.1.201.1.2.15 | |||
| swL2StormCtrlTable | 1.3.6.1.4.1.2272.1.201.1.2.15.1 | not-accessible | This table specifys the storm traffic control configuration. | |
| swL2StormCtrlEntry | 1.3.6.1.4.1.2272.1.201.1.2.15.1.1 | not-accessible | A list of information specifies the storm traffic control configuration. | |
| INT swL2StormCtrlPortIndex | 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.1 | INTEGER | read-only | The index of logical port. |
| INT swL2StormCtrlBcastStormCtrl | 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.2 | INTEGER | read-write | This object indicates broadcast storm control function is enabled or disabled. |
| INT swL2StormCtrlMcastStormCtrl | 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.3 | INTEGER | read-write | This object indicates multicast storm control function is enabled or disabled. |
| INT swL2StormCtrlBMStormThreshold | 1.3.6.1.4.1.2272.1.201.1.2.15.1.1.4 | INTEGER | read-write | This object to decide how much percentage packets per second broadcast/multicast (depend on swL2StormCtrlBcastStormCtrl or swL2StormCtrlMcastStormCtrl objects whether is enabled) will active storm control. Whenever a port reaches its configured percent of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet. |
| INT swL2StormCtrlDlfState | 1.3.6.1.4.1.2272.1.201.1.2.15.2 | INTEGER | read-write | This object indicates destination lookup fail function is enabled or disabled. |
| INT swL2StormCtrlDlfThreshold | 1.3.6.1.4.1.2272.1.201.1.2.15.3 | INTEGER | read-write | This object to decide how much packets per second destination lookup fail (depend on swL2StormCtrlDlfState objects whether is enabled) will active storm control. Whenever the device reaches its configured packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will start forwarding that type of packet. This value must be the multiples of 8192. |
| swL2CpuRateLimitTable | 1.3.6.1.4.1.2272.1.201.1.2.15.4 | not-accessible | This table specifys the CPU rate limit per port. Once too much broadcast/multicast traffic, exceed CP-Limit, comes in from a port, the port state will be disabled. | |
| swL2CpuRateLimitEntry | 1.3.6.1.4.1.2272.1.201.1.2.15.4.1 | not-accessible | A list of information specifies the CPU rate limit of the port configuration. | |
| INT swL2CpuRateLimitPortIndex | 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.1 | INTEGER | read-only | The index of logical port. |
| INT swL2CpuRateLimitState | 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.2 | INTEGER | read-write | This object indicates CPU rate limit function is enabled or disabled. |
| INT swL2CpuRateLimitBcastThreshold | 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.3 | INTEGER | read-write | This object to decide how much packets per second broadcast will active traffic control. Whenever a port reaches its configured packets in the one second time interval, the port will be disabled. |
| INT swL2CpuRateLimitMcastThreshold | 1.3.6.1.4.1.2272.1.201.1.2.15.4.1.4 | INTEGER | read-write | This object to decide how much packets per second multicast will active traffic control. Whenever a port reaches its configured packets in the one second time interval, the port will be disabled. |
| INT swL2CpuUtilization | 1.3.6.1.4.1.2272.1.201.1.2.15.5 | INTEGER | read-only | The utilization of CPU. |
| swL2ACLQosMgmt | 1.3.6.1.4.1.2272.1.201.1.2.16 | |||
| INT swL2ACLQosTemplate1Mode | 1.3.6.1.4.1.2272.1.201.1.2.16.1 | INTEGER | read-write | This object decide the operate mode of template_1. |
| INT swL2ACLQosTemplate2Mode | 1.3.6.1.4.1.2272.1.201.1.2.16.2 | INTEGER | read-write | This object decide the operate mode of template_2. |
| swL2ACLQosFlowClassifierTable | 1.3.6.1.4.1.2272.1.201.1.2.16.3 | not-accessible | This table specifys the template of flow classifier. | |
| swL2ACLQosFlowClassifierEntry | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1 | not-accessible | A list of information specifies the template of flow classifier. | |
| INT swL2ACLQosFlowClassifierTemplateId | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.1 | INTEGER | read-only | The index of template ID. |
| INT swL2ACLQosFlowClassifierCurrentMode | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.2 | INTEGER | read-only | The current operated mode of this template. |
| IP swL2ACLQosFlowClassifierSecuritySrcMask | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.3 | IpAddress | read-write | This object indicates a source IP subnet rule for the switch. If the swL2ACLQosFlowClassifierCurrentMode is not security(2), then this object must be 0.0.0.0. |
| INT swL2ACLQosFlowClassifierQosFlavor | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.4 | INTEGER | read-write | These parameters define what characteristics an incoming packet must meet. One or more of the above parameters must be defined. If the swL2ACLQosFlowClassifierCurrentMode is not qos(3), then this object must be flavor-un-used(6). |
| INT swL2ACLQosFlowClassifierL4SwitchTCPDstIp | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.5 | INTEGER | read-write | This object indicate the destination ipaddress in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchTCPSrcIp | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.6 | INTEGER | read-write | This object indicate the source ipaddress in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchTCPTos | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.7 | INTEGER | read-write | This object indicate the type of service in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchTCPDstPort | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.8 | INTEGER | read-write | This object indicate the destination TCP port number in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchTCPSrcPort | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.9 | INTEGER | read-write | This object indicate the source TCP port number in the configured L4 TCP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchTCPFlags | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.10 | INTEGER | read-write | This object indicate the TCP flags in the configured L4 TCP- session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchUDPDstIp | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.11 | INTEGER | read-write | This object indicate the destination ipaddress in the configured L4 UDP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchUDPSrcIp | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.12 | INTEGER | read-write | This object indicate the source ipaddress in the configured L4 UDP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchUDPTos | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.13 | INTEGER | read-write | This object indicate the type of service in the configured L4 UDP-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchUDPDstPort | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.14 | INTEGER | read-write | This object indicate the destination UDP port number in the configured L4 UDP session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchUDPSrcPort | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.15 | INTEGER | read-write | This object indicate the source UDP port number in the configured L4 UDP session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchOtherDstIp | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.16 | INTEGER | read-write | This object indicate the destination ipaddress in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchOtherSrcIp | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.17 | INTEGER | read-write | This object indicate the source ipaddress in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchOtherTos | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.18 | INTEGER | read-write | This object indicate the type of service in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchOtherL4Protocol | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.19 | INTEGER | read-write | This object indicate the l4_protocol in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchOtherICMPMessage | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.20 | INTEGER | read-write | This object indicate the ICMP message in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierL4SwitchOtherIGMPType | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.21 | INTEGER | read-write | This object indicate the IGMP type in the configured L4 OTHER-session rule entries must be checked or not. If the swL2ACLQosFlowClassifierCurrentMode is not l4-switch(4), then this object must be un-used(3). |
| INT swL2ACLQosFlowClassifierActiveRuleNumber | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.22 | INTEGER | read-only | This object indicates the number of active rule. |
| IP swL2ACLQosFlowClassifierSecurityDstMask | 1.3.6.1.4.1.2272.1.201.1.2.16.3.1.23 | IpAddress | read-write | This object indicates a destination IP subnet rule for the switch. If the swL2ACLQosFlowClassifierCurrentMode is not security(2), then this object must be 0.0.0.0. |
| swL2ACLQosFlowClassifierVlanTable | 1.3.6.1.4.1.2272.1.201.1.2.16.4 | not-accessible | This table specifys which vlan has been binded in the template. | |
| swL2ACLQosFlowClassifierVlanEntry | 1.3.6.1.4.1.2272.1.201.1.2.16.4.1 | not-accessible | A list of information which vlan has been binded in the template. | |
| INT swL2ACLQosFlowClassifierVlanTemplateId | 1.3.6.1.4.1.2272.1.201.1.2.16.4.1.1 | INTEGER | read-only | The index of template ID. |
| STR swL2ACLQosFlowClassifierVlanVlanName | 1.3.6.1.4.1.2272.1.201.1.2.16.4.1.2 | DisplayString | read-only | The existence of VLAN name. |
| INT swL2ACLQosFlowClassifierVlanState | 1.3.6.1.4.1.2272.1.201.1.2.16.4.1.3 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. attached(2) - this entry is reside in the table. detached(3) - writing this value to the object, and then the corresponding entry will be removed from the table. |
| swL2ACLQosTemplateRuleTable | 1.3.6.1.4.1.2272.1.201.1.2.16.5 | not-accessible | This table specifys the template-depend rules. | |
| swL2ACLQosTemplateRuleEntry | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1 | not-accessible | A list of information specifies the template-depend rules. | |
| INT swL2ACLQosTemplateRuleTemplateId | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.1 | INTEGER | read-only | The index of template ID. |
| INT swL2ACLQosTemplateRuleIndex | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.2 | INTEGER | read-only | The index of template rule. |
| INT swL2ACLQosTemplateRuleMode | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.3 | INTEGER | read-only | This object indicates the rule type of the entry. |
| IP swL2ACLQosTemplateRuleSecuritySrcIp | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.4 | IpAddress | read-write | This object indicates the source IP of flow template. If the swL2ACLQosTemplateRuleMode is not security(2), then this object will be display 0.0.0.0. |
| INT swL2ACLQosTemplateRuleQosFlavor | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.5 | INTEGER | read-only | This object indicates the rule type of the QOS mode. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be flavor-un-used(6). |
| OCT swL2ACLQosTemplateRuleQosValue | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.6 | OCTET STRING | read-write | This object must match with swL2ACLQosTemplateRuleQosFlavor. If the type is flavor-8021p(1), the range of this object is 0~7. If the type is flavor-dscp(2), the range of this object is 0~63. If the type is flavor-tcp(4) or flavor-udp(5), the range of this object is 1~65535. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be NULL. |
| INT swL2ACLQosTemplateRuleQosPriority | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.7 | INTEGER | read-write | This object indicates the priority of ingress packets in QOS mode. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be 0. |
| INT swL2ACLQosTemplateRuleQosDscp | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.8 | INTEGER | read-write | This object indicates the Dscp of ingress packets in QOS mode. If the swL2ACLQosTemplateRuleMode is not qos(3), then this object must be 0. |
| INT swL2ACLQosTemplateRuleL4SwitchSessionType | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.9 | INTEGER | read-write | This object indicates the rule type of the TCP-Session in L4-Switch mode. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(4). |
| IP swL2ACLQosTemplateRuleL4SwitchSessionTCPDstIp | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.10 | IpAddress | read-write | This object indicates the destination ipaddress in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. |
| IP swL2ACLQosTemplateRuleL4SwitchSessionTCPSrcIp | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.11 | IpAddress | read-write | This object indicates the source ipaddress in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. |
| OCT swL2ACLQosTemplateRuleL4SwitchSessionTCPTos | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.12 | OCTET STRING | read-write | This object indicates the type of service in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. |
| INT swL2ACLQosTemplateRuleL4SwitchSessionTCPDstPort | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.13 | INTEGER | read-write | This object indicates the destination TCP port number in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0. |
| INT swL2ACLQosTemplateRuleL4SwitchSessionTCPSrcPort | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.14 | INTEGER | read-write | This object indicates the source TCP port number in the configured L4 TCP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0. |
| INT swL2ACLQosTemplateRuleL4SwitchSessionTCPFlags | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.15 | INTEGER | read-write | This object indicates the TCP flags in the configured L4 TCP- session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(7). This object is deprecated because it just can let user to choose one of these items. |
| IP swL2ACLQosTemplateRuleL4SwitchSessionUDPDstIp | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.16 | IpAddress | read-write | This object indicates the destination ipaddress in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. |
| IP swL2ACLQosTemplateRuleL4SwitchSessionUDPSrcIp | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.17 | IpAddress | read-write | This object indicates the soruce ipaddress in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. |
| OCT swL2ACLQosTemplateRuleL4SwitchSessionUDPTos | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.18 | OCTET STRING | read-write | This object indicates the type of service in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. |
| INT swL2ACLQosTemplateRuleL4SwitchSessionUDPDstPort | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.19 | INTEGER | read-write | This object indicates the destination UDP port number in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0. |
| INT swL2ACLQosTemplateRuleL4SwitchSessionUDPSrcPort | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.20 | INTEGER | read-write | This object indicates the source UDP port number in the configured L4 UDP-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0. |
| IP swL2ACLQosTemplateRuleL4SwitchSessionOtherDstIp | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.21 | IpAddress | read-write | This object indicates the destination ipaddress in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. |
| IP swL2ACLQosTemplateRuleL4SwitchSessionOtherSrcIp | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.22 | IpAddress | read-write | This object indicates the source ipaddress in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be 0.0.0.0. |
| OCT swL2ACLQosTemplateRuleL4SwitchSessionOtherTos | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.23 | OCTET STRING | read-write | This object indicates the type of service in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. |
| INT swL2ACLQosTemplateRuleL4SwitchSessionOtherL4Protocol | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.24 | INTEGER | read-write | This object indicates the l4_protocol in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(3). |
| OCT swL2ACLQosTemplateRuleL4SwitchSessionOtherICMPType | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.25 | OCTET STRING | read-write | This object indicates the type of ICMP message in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. |
| OCT swL2ACLQosTemplateRuleL4SwitchSessionOtherICMPCode | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.26 | OCTET STRING | read-write | This object indicates the code of ICMP message in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. |
| INT swL2ACLQosTemplateRuleL4SwitchSessionOtherIGMPType | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.27 | INTEGER | read-write | This object indicates the IGMP type in the configured L4 OTHER-session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(5). If the object be set to response-version-all(4), it means to create two entries with response-version-1(2) and response-version-2(3). |
| INT swL2ACLQosTemplateRuleL4SwitchActionType | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.28 | INTEGER | read-write | This object indicates the action when a packet matches an entry of l4_switch mode. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be un-used(4). |
| INT swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.29 | INTEGER | read-write | This object decide to sending the packet to one of 8 hardware priority queues or not. |
| INT swL2ACLQosTemplateRuleL4SwitchActionForwardPriority | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.30 | INTEGER | read-write | This object indicates the priority related to one of 8 hardware priority queues. If the swL2ACLQosTemplateRuleMode is not l4-switch(4) or the swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState is not true(2), this object must be 0. |
| INT swL2ACLQosTemplateRuleL4SwitchActionForwardDscp | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.31 | INTEGER | read-write | If the swL2ACLQosTemplateRuleMode is not l4-switch(4) or the swL2ACLQosTemplateRuleL4SwitchActionForwardPriorityState is not true(2),, this object must be 0. |
| IP swL2ACLQosTemplateRuleL4SwitchActionRedirectIp | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.32 | IpAddress | read-write | This object indicates the redirected IP address that when a packet matches an entry of l4_switch mode. If the swL2ACLQosTemplateRuleL4SwitchActionType is not redirect(3), this object must be 0.0.0.0. |
| INT swL2ACLQosTemplateRuleL4SwitchActionRedirectDropUnreachable | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.33 | INTEGER | read-write | This object indicates the action of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. false(2) - routing unreachable packet by using L2/IPv4 router forwarding table. true(3) - dropping unreachable packet |
| INT swL2ACLQosTemplateRuleState | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.34 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| BIT swL2ACLQosTemplateRuleL4SwitchSessionTCPFlagsAll | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.35 | Bits | read-write | This object indicates the TCP flags in the configured L4 TCP- session rule entries. If the swL2ACLQosTemplateRuleMode is not l4-switch(4), then this object must be zero. |
| IP swL2ACLQosTemplateRuleSecurityDstIp | 1.3.6.1.4.1.2272.1.201.1.2.16.5.1.36 | IpAddress | read-write | This object indicates the destination IP of flow template. If the swL2ACLQosTemplateRuleMode is not security(2), then this object will be display 0.0.0.0. |
| swL2ACLQosDestinationIpFilterTable | 1.3.6.1.4.1.2272.1.201.1.2.16.6 | not-accessible | This table defines information for the device to filter packets with specific Destination IP address. The IP address can be a unicast address or multicast address. This table has higher priority than both static FDB table and IGMP table. It means that if a IP address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet. | |
| swL2ACLQosDestinationIpFilterEntry | 1.3.6.1.4.1.2272.1.201.1.2.16.6.1 | not-accessible | A list of information about a specific unicast/multicast IP address for which the switch has filtering information. | |
| INT swL2ACLQosDestinationIpFilterIndex | 1.3.6.1.4.1.2272.1.201.1.2.16.6.1.1 | INTEGER | read-only | The index of this rule. |
| IP swL2ACLQosDestinationIpFilterIpAddr | 1.3.6.1.4.1.2272.1.201.1.2.16.6.1.2 | IpAddress | read-only | This object indicates a unicast IP address for which the switch has filtering information. |
| INT swL2ACLQosDestinationIpFilterState | 1.3.6.1.4.1.2272.1.201.1.2.16.6.1.3 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| swL2ACLQosFDBFilterTable | 1.3.6.1.4.1.2272.1.201.1.2.16.7 | not-accessible | This table defines information for the device to filter packets with specific MAC address (either as the DA and/or as the SA). The MAC address can be a unicast address or a multicast address. This table has higher priority than both static FDB table and IGMP table. It means that if a MAC address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet. | |
| swL2ACLQosFDBFilterEntry | 1.3.6.1.4.1.2272.1.201.1.2.16.7.1 | not-accessible | A list of information about a specific unicast/multicast MAC address for which the switch has filtering information. | |
| INT swL2ACLQosFDBFilterIndex | 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.1 | INTEGER | read-only | The index of this rule. |
| STR swL2ACLQosFDBFilterVlanName | 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.2 | DisplayString | read-only | The existence of VALN name. |
| MAC swL2ACLQosFDBFilterMacAddress | 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.3 | MacAddress | read-only | This object will filter on destination MAC address operates on bridged packets, but not on routed packets. And It will filter on source MAC operates on all packets. |
| INT swL2ACLQosFDBFilterState | 1.3.6.1.4.1.2272.1.201.1.2.16.7.1.4 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| INT swL2ACLQosIpFragmentFilterDropPkts | 1.3.6.1.4.1.2272.1.201.1.2.16.8 | INTEGER | read-write | This object decide to drop fragmented IP packets or not. |
| swL2ACLQosSchedulingTable | 1.3.6.1.4.1.2272.1.201.1.2.16.9 | not-accessible | The switch contains 4 hardware priority queues. Incoming packets must be mapped to one of these four queues. Each hardware queue will transmit all of the packets in its buffer before allowing the next lower priority queue to transmit its packets. When the lowest hardware priority queue has finished transmitting all of its packets, the highest hardware priority queue can again transmit any packets it may have received. | |
| swL2ACLQosSchedulingEntry | 1.3.6.1.4.1.2272.1.201.1.2.16.9.1 | not-accessible | A list of information specifies the Qos output scheduling Table. | |
| INT swL2ACLQosSchedulingPortIndex | 1.3.6.1.4.1.2272.1.201.1.2.16.9.1.1 | INTEGER | read-only | The index of logical port. |
| INT swL2ACLQosSchedulingClassId | 1.3.6.1.4.1.2272.1.201.1.2.16.9.1.2 | INTEGER | read-only | This specifies which of the four hardware priority queues. The four hardware priority queues are identified by number, from 0 to 3, with the 0 queue being the lowest priority. |
| INT swL2ACLQosSchedulingWRRValue | 1.3.6.1.4.1.2272.1.201.1.2.16.9.1.3 | INTEGER | read-write | Specifies the weighted round robin (WRR) the above specified hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. |
| swL2ACLQosMacPriorityTable | 1.3.6.1.4.1.2272.1.201.1.2.16.10 | not-accessible | This table indicates the destination mac priority in flow classifier. | |
| swL2ACLQosMacPriorityEntry | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1 | not-accessible | A list of information specifies the destination mac priority in flow classifier. | |
| INT swL2ACLQosMacPriorityIndex | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.1 | INTEGER | read-only | The index of this rule. |
| STR swL2ACLQosMacPriorityVlanName | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.2 | DisplayString | read-only | The existence VLAN name. |
| MAC swL2ACLQosMacPriorityDstMacAddress | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.3 | MacAddress | read-only | This object will filter on destination MAC address operates on bridged packets, but not on routed packets. And It will filter on source MAC operates on all packets. |
| INT swL2ACLQosMacPriorityPriorityValue | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.4 | INTEGER | read-write | This object indicates the priority related to one of 8 hardware priority queues. |
| INT swL2ACLQosMacPriorityState | 1.3.6.1.4.1.2272.1.201.1.2.16.10.1.5 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| swL2MgmtPortMgmt | 1.3.6.1.4.1.2272.1.201.1.2.17 | |||
| INT swL2MgmtPortCurrentLinkStatus | 1.3.6.1.4.1.2272.1.201.1.2.17.1 | INTEGER | read-only | This object indicates the current management port link status. |
| INT swL2MgmtPortCurrentNwayStatus | 1.3.6.1.4.1.2272.1.201.1.2.17.2 | INTEGER | read-only | This object indicates the current management port speed and duplex mode. |
| INT swL2MgmtPortAdminState | 1.3.6.1.4.1.2272.1.201.1.2.17.3 | INTEGER | read-write | This object decide the management port enabled or disabled. |
| INT swL2MgmtPortNwayState | 1.3.6.1.4.1.2272.1.201.1.2.17.4 | INTEGER | read-write | Chose the management port speed, duplex mode, and N-Way function mode. |
| INT swL2MgmtPortFlowCtrlState | 1.3.6.1.4.1.2272.1.201.1.2.17.5 | INTEGER | read-write | The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames. |
| INT swL2MgmtPortLinkUpDownTrapEnable | 1.3.6.1.4.1.2272.1.201.1.2.17.6 | INTEGER | read-write | Indicates whether linkUp/linkDown traps should be generated for the management port. By default, this object should have the value enabled(3). |
RFC description
D-Link Layer 2 network management MIB that provides management objects for switch port information, spanning tree configuration, IGMP snooping, and other Layer 2 switching features.
Start monitoring D-Link managed Layer 2 Ethernet switch (MAC learning/VLAN/spanning-tree status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.