All MIBs › SWL3MGMT-MIB
Organization: enterprise, Inc.
Last Updated: 2000-07-15
Category: Routing and Layer 3, Switch Management - D-Link
Description: Manages Layer 3 switch routing functions including IP interfaces, static routes, and ARP on D-Link platforms.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is SWL3MGMT-MIB?
SWL3MGMT-MIB is a proprietary D-Link enterprise MIB module that defines management objects for Layer 3 switching functions on D-Link's managed switch platforms. It exposes configuration and status data for IP interfaces, static routing tables, and ARP entries used in inter-VLAN routing. The practical monitoring surface centers on confirming a switch's routing engine is healthy and correctly forwarding traffic between subnets, rather than on hardware sensors, since no environmental or CPU/memory objects are part of this module. It likely depends on or complements standard IETF MIBs such as IF-MIB and IP-MIB for base interface and IP addressing semantics. It is deployed in enterprise and campus networks using D-Link Layer 3 managed switches as core or distribution-layer routing devices. Engineers can download the SWL3MGMT-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in SWL3MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- D-Link Layer 3 managed switches
Monitoring Examples
No concrete object or table names were captured from this MIB's parsed source, so a precise polling scenario can't be grounded in specific identifiers. In practice, an administrator would poll IP interface, static route, and ARP table objects to confirm routes are present and reachable, with a missing static route or a stale/incomplete ARP table pointing to an inter-VLAN routing or connectivity fault on the switch.
What Can Be Monitored
- IP interface status
- static route table entries
- ARP table entries
- L3 routing configuration state
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| ifIndex | OBJECT-TYPE |
From OSPF-MIB
| AreaID | |
| Metric | |
| TOSType |
From SNMPv2-SMI
| Counter32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| PhysAddress | |
| RowStatus | |
| TimeStamp | |
| TruthValue |
From SWPRIMGMT-MIB
| privateMgmt | OBJECT-IDENTITY |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| swL3DevCtrl | 1.3.6.1.4.1.2272.1.201.1.3.1.1 | |||
| INT swL3DevCtrlDVMRPState | 1.3.6.1.4.1.2272.1.201.1.3.1.1.3 | INTEGER | read-write | This object indicates DVMRP protocol is enabled or disabled. |
| INT swL3DevCtrlOSPFState | 1.3.6.1.4.1.2272.1.201.1.3.1.1.2 | INTEGER | read-write | This object indicates OSPF protocol is enabled or disabled. |
| INT swL3DevCtrlRIPState | 1.3.6.1.4.1.2272.1.201.1.3.1.1.1 | INTEGER | read-write | This object indicates Routing Information Protocol (RIP) version 2 function is enabled or disabled. |
| INT swL3DevCtrlVRRPPingVirtualAddrState | 1.3.6.1.4.1.2272.1.201.1.3.1.1.5 | INTEGER | read-write | This object let host can ping the virtual ip address or not. Default is disabled(2). |
| INT swL3DevCtrlVRRPState | 1.3.6.1.4.1.2272.1.201.1.3.1.1.4 | INTEGER | read-write | This object indicates VRRP protocol is enabled or disabled. |
| swL3DevMgmt | 1.3.6.1.4.1.2272.1.201.1.3.1 | |||
| swL3DvmrpInterfaceEntry | 1.3.6.1.4.1.2272.1.201.1.3.9.1 | not-accessible | An entry (conceptual row) in the swL3DvmrpInterfaceTable. | |
| INT swL3DvmrpInterfaceIfIndex | 1.3.6.1.4.1.2272.1.201.1.3.9.1.1 | INTEGER | not-accessible | The ifIndex value of the interface for which DVMRP is enabled. |
| INT swL3DvmrpInterfaceNeighborTimeout | 1.3.6.1.4.1.2272.1.201.1.3.9.1.2 | INTEGER | read-write | The time period for DVMRP will hold Neithbor Router reports before issuing poison route messages. The unit is second. |
| INT swL3DvmrpInterfaceProbe | 1.3.6.1.4.1.2272.1.201.1.3.9.1.3 | INTEGER | read-write | DVMRP defines an extension to IGMP that allows routers to query other routers to determine if a multicast group is present on an given router subnetwork or not. This is referred to as a 'probe'. The unit is second. |
| swL3DvmrpInterfaceTable | 1.3.6.1.4.1.2272.1.201.1.3.9 | not-accessible | The (conceptual) table listing the router's multicast- capable interfaces. | |
| INT swL3IpArpAgingTime | 1.3.6.1.4.1.2272.1.201.1.3.2.4 | INTEGER | read-write | The timeout period in minutes for aging out dynamically learned arp information. |
| INT swL3IpArpDynamicAgingTime | 1.3.6.1.4.1.2272.1.201.1.3.2.6.1.5 | INTEGER | read-only | The timeout period in seconds for aging out dynamically learned arp information. If the swL3IpArpType is not dynamic(3), this object will display zero. |
| swL3IpArpEntry | 1.3.6.1.4.1.2272.1.201.1.3.2.6.1 | not-accessible | Each entry contains one IpAddress to `physical' address equivalence. | |
| INT swL3IpArpIfIndex | 1.3.6.1.4.1.2272.1.201.1.3.2.6.1.1 | INTEGER | read-only | The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex. |
| IP swL3IpArpNetAddress | 1.3.6.1.4.1.2272.1.201.1.3.2.6.1.2 | IpAddress | read-only | The IpAddress corresponding to the media-dependent `physical' address. |
| MAC swL3IpArpPhysAddress | 1.3.6.1.4.1.2272.1.201.1.3.2.6.1.3 | MacAddress | read-create | The media-dependent `physical' address. |
| INT swL3IpArpReqRateLimitState | 1.3.6.1.4.1.2272.1.201.1.3.2.7 | INTEGER | read-write | To enable limit ARP requests trapped to CPU or disabled. |
| INT swL3IpArpReqRateLimitValue | 1.3.6.1.4.1.2272.1.201.1.3.2.8 | INTEGER | read-write | To configure how much frames per second that ARP request limit. This value will be usefull only when swL3IpArpReqRateLimitState is enabled. |
| swL3IpArpTable | 1.3.6.1.4.1.2272.1.201.1.3.2.6 | not-accessible | The ARP table used for mapping from IP addresses to physical addresses. | |
| INT swL3IpArpType | 1.3.6.1.4.1.2272.1.201.1.3.2.6.1.4 | INTEGER | read-create | The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the swL3IpArpTable. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant swL3IpArpType object. |
| swL3IpCtrlEntry | 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1 | not-accessible | A list of information about a specific IP interface. | |
| INT swL3IpCtrlIfIndex | 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.2 | INTEGER | read-only | This object uniquely identifies the IP interface number in the swL3IpCtrlTable. |
| STR swL3IpCtrlInterfaceName | 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.1 | DisplayString | read-only | This object indicates the name of the IP interface. |
| IP swL3IpCtrlIpAddr | 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.3 | IpAddress | read-write | The IP address of the interface. This object only can take the value of the unicast IP address. |
| IP swL3IpCtrlIpSubnetMask | 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.4 | IpAddress | read-write | The IP net mask for this interface. |
| swL3IpCtrlMgmt | 1.3.6.1.4.1.2272.1.201.1.3.2.1 | |||
| INT swL3IpCtrlMode | 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.6 | INTEGER | read-write | This object indicates the IP operation mode. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. manual(2) - the IP address will be set by manual. bootp(3) - the IP address will be set automatically from BOOTP server. dhcp(4) - the IP address will be set automatically from DHCP server. |
| INT swL3IpCtrlOperState | 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.8 | INTEGER | read-only | The current operational state of the IP interface. |
| ROW swL3IpCtrlState | 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.7 | RowStatus | read-create | This variable displays the status of the entry. The status used for creating, modifying, and deleting instances of the objects in this table. |
| swL3IpCtrlTable | 1.3.6.1.4.1.2272.1.201.1.3.2.1.1 | not-accessible | This table contain IP interface information. | |
| STR swL3IpCtrlVlanName | 1.3.6.1.4.1.2272.1.201.1.3.2.1.1.1.5 | DisplayString | read-write | This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table. |
| swL3IpFdbInfoEntry | 1.3.6.1.4.1.2272.1.201.1.3.2.2.1.1 | not-accessible | Information about a specific IP address for which the bridge has some forwarding and/or filtering information. | |
| IP swL3IpFdbInfoIpAddr | 1.3.6.1.4.1.2272.1.201.1.3.2.2.1.1.1 | IpAddress | read-only | A IP address for which switch has forwarding and/or filtering information. |
| IP swL3IpFdbInfoIpSubnetMask | 1.3.6.1.4.1.2272.1.201.1.3.2.2.1.1.2 | IpAddress | read-only | A IP net mask for this interface.for which switch has forwarding and/or filtering information. |
| INT swL3IpFdbInfoPort | 1.3.6.1.4.1.2272.1.201.1.3.2.2.1.1.3 | INTEGER | read-only | Either the value '0', or the port number of the port on which packet having a IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that switch does have some forwarding/filtering information about this address. |
| swL3IpFdbInfoTable | 1.3.6.1.4.1.2272.1.201.1.3.2.2.1 | not-accessible | A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets. | |
| INT swL3IpFdbInfoType | 1.3.6.1.4.1.2272.1.201.1.3.2.2.1.1.4 | INTEGER | read-only | The status of this entry. |
| swL3IpFdbMgmt | 1.3.6.1.4.1.2272.1.201.1.3.2.2 | |||
| swL3IpFilterAddrConfig | 1.3.6.1.4.1.2272.1.201.1.3.2.3.1 | |||
| swL3IpFilterAddrCtrlEntry | 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.3.1 | not-accessible | A list of information about a specific unicast/multicast IP address for which the switch has filtering information. | |
| INT swL3IpFilterAddrCtrlState | 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.3.1.2 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. dst-addr(2) - recieved frames's destination address are currently used to be filtered as it meets with the IP address entry of the table. src-addr(3) - recieved frames's source address are currently used to be filtered as it meets with the IP address entry of the table. dst-src-addr(4) - recieved frames's destination address or source address are currently used to be filtered as it meets with the IP address entry of the table. invalid(5) - writing this value to the object, and then the corresponding entry will be removed from the table. |
| swL3IpFilterAddrCtrlTable | 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.3 | not-accessible | This table defines information for the device to filter packets with specific IP address (either as the DA and/or as the SA). The IP address can be a unicast address or multicast address. This table has higher priority than both static FDB table and IGMP table. It means that if a IP address appears on this table also appears on the static FDB table, the device will use the information provide by this table to process the packet. | |
| INT swL3IpFilterAddrCurrentTotalEntries | 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.2 | INTEGER | read-only | Current applied number of entries in the IP address filtering table. If the swL3IpFilterAddrCtrlState = dst-src-addr, then it means there are two entries in swL3IpFilterAddrCtrlTable. |
| IP swL3IpFilterAddrIpAddr | 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.3.1.1 | IpAddress | read-only | This object indicates a unicast/multicast IP address for which the switch has filtering information. But if the swL3IpFilterAddrCtrlState = src-addr, then the object can not be a multicast IP address (Class D IP address). |
| INT swL3IpFilterAddrMaxSupportedEntries | 1.3.6.1.4.1.2272.1.201.1.3.2.3.1.1 | INTEGER | read-only | Maximum number of entries in the IP address filtering table (swL3IpFilterAddrCtrlTable) . |
| swL3IpFilterMgmt | 1.3.6.1.4.1.2272.1.201.1.3.2.3 | |||
| swL3IpMgmt | 1.3.6.1.4.1.2272.1.201.1.3.2 | |||
| IP swL3IpStaticRouteDest | 1.3.6.1.4.1.2272.1.201.1.3.2.5.1.1 | IpAddress | read-only | The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteMask object is not equal to x. |
| swL3IpStaticRouteEntry | 1.3.6.1.4.1.2272.1.201.1.3.2.5.1 | not-accessible | A particular route to a particular destination, under a particular policy. | |
| IP swL3IpStaticRouteMask | 1.3.6.1.4.1.2272.1.201.1.3.2.5.1.2 | IpAddress | read-only | Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpStaticRouteMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteDest object is not equal to swL3IpStaticRouteDest. |
| INT swL3IpStaticRouteMetric | 1.3.6.1.4.1.2272.1.201.1.3.2.5.1.4 | INTEGER | read-create | The routing metric for this route. |
| IP swL3IpStaticRouteNextHop | 1.3.6.1.4.1.2272.1.201.1.3.2.5.1.3 | IpAddress | read-only | On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0. |
| INT swL3IpStaticRouteStatus | 1.3.6.1.4.1.2272.1.201.1.3.2.5.1.5 | INTEGER | read-create | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| swL3IpStaticRouteTable | 1.3.6.1.4.1.2272.1.201.1.3.2.5 | not-accessible | This entity's IP static Routing table. | |
| swL3Md5Entry | 1.3.6.1.4.1.2272.1.201.1.3.4.1 | not-accessible | A list of information display the current MD5 key table. | |
| STR swL3Md5Key | 1.3.6.1.4.1.2272.1.201.1.3.4.1.2 | DisplayString | read-write | An MD5 password of up to 16 bytes. |
| INT swL3Md5KeyId | 1.3.6.1.4.1.2272.1.201.1.3.4.1.1 | INTEGER | read-only | The MD5 key ID. |
| INT swL3Md5State | 1.3.6.1.4.1.2272.1.201.1.3.4.1.3 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| swL3Md5Table | 1.3.6.1.4.1.2272.1.201.1.3.4 | not-accessible | This table display the current MD5 key table. | |
| swL3MgmtMIB | 1.3.6.1.4.1.2272.1.201.1.3 | The Structure of Layer 3 Network Management Information for the proprietary enterprise. | ||
| ARE swL3OspfHostAreaID | 1.3.6.1.4.1.2272.1.201.1.3.6.1.5 | AreaID | read-write | The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF interface is in, or 0.0.0.0 |
| swL3OspfHostEntry | 1.3.6.1.4.1.2272.1.201.1.3.6.1 | not-accessible | A metric to be advertised, for a given type of service, when a given host is reachable. | |
| IP swL3OspfHostIpAddress | 1.3.6.1.4.1.2272.1.201.1.3.6.1.1 | IpAddress | read-only | The IP Address of the Host. |
| MET swL3OspfHostMetric | 1.3.6.1.4.1.2272.1.201.1.3.6.1.3 | Metric | read-write | The Metric to be advertised. |
| ROW swL3OspfHostStatus | 1.3.6.1.4.1.2272.1.201.1.3.6.1.4 | RowStatus | read-write | This variable displays the status of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent. |
| swL3OspfHostTable | 1.3.6.1.4.1.2272.1.201.1.3.6 | not-accessible | The list of Hosts, and their metrics, that the router will advertise as host routes. | |
| TOS swL3OspfHostTOS | 1.3.6.1.4.1.2272.1.201.1.3.6.1.2 | TOSType | read-only | The Type of Service of the route being configured. |
| swL3RelayBootpCtrlEntry | 1.3.6.1.4.1.2272.1.201.1.3.3.1.4.1 | not-accessible | A list of information specifies the IP address as a destination to forward (relay) BOOTP packets to. | |
| STR swL3RelayBootpCtrlInterfaceName | 1.3.6.1.4.1.2272.1.201.1.3.3.1.4.1.1 | DisplayString | read-only | The name of the IP interface. |
| IP swL3RelayBootpCtrlServer | 1.3.6.1.4.1.2272.1.201.1.3.3.1.4.1.2 | IpAddress | read-only | The BOOTP server IP address. |
| INT swL3RelayBootpCtrlState | 1.3.6.1.4.1.2272.1.201.1.3.3.1.4.1.3 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| swL3RelayBootpCtrlTable | 1.3.6.1.4.1.2272.1.201.1.3.3.1.4 | not-accessible | This table specifys the IP address as a destination to forward (relay) BOOTP packets to. | |
| INT swL3RelayBootpHopCount | 1.3.6.1.4.1.2272.1.201.1.3.3.1.2 | INTEGER | read-write | This object indicates the maximum number of router hops that the BOOTP packets can cross. |
| swL3RelayBootpMgmt | 1.3.6.1.4.1.2272.1.201.1.3.3.1 | |||
| INT swL3RelayBootpState | 1.3.6.1.4.1.2272.1.201.1.3.3.1.1 | INTEGER | read-write | This object indicates BOOTP Relay function is enabled or disabled. |
| INT swL3RelayBootpTimeThreshold | 1.3.6.1.4.1.2272.1.201.1.3.3.1.3 | INTEGER | read-write | This object indicates the minimum time in seconds within which the switch must relay the BOOTP request. If this time is exceeded, the switch will drop the BOOTP packet. |
| INT swL3RelayDnsCacheState | 1.3.6.1.4.1.2272.1.201.1.3.3.2.4 | INTEGER | read-write | This object indicates DNS Relay cache is enabled or disabled. |
| STR swL3RelayDnsCtrlDomainName | 1.3.6.1.4.1.2272.1.201.1.3.3.2.6.1.1 | DisplayString | read-only | The domain name of the entry. |
| swL3RelayDnsCtrlEntry | 1.3.6.1.4.1.2272.1.201.1.3.3.2.6.1 | not-accessible | A list of information display the current DNS relay static table. | |
| IP swL3RelayDnsCtrlIpAddr | 1.3.6.1.4.1.2272.1.201.1.3.3.2.6.1.2 | IpAddress | read-only | The IP address of the entry. |
| INT swL3RelayDnsCtrlState | 1.3.6.1.4.1.2272.1.201.1.3.3.2.6.1.3 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| swL3RelayDnsCtrlTable | 1.3.6.1.4.1.2272.1.201.1.3.3.2.6 | not-accessible | This table display the current DNS relay static table. | |
| swL3RelayDnsMgmt | 1.3.6.1.4.1.2272.1.201.1.3.3.2 | |||
| IP swL3RelayDnsPrimaryServer | 1.3.6.1.4.1.2272.1.201.1.3.3.2.2 | IpAddress | read-write | This object indicates the address of the primary DNS server. |
| IP swL3RelayDnsSecondaryServer | 1.3.6.1.4.1.2272.1.201.1.3.3.2.3 | IpAddress | read-write | This object indicates the address of the secondary DNS server. |
| INT swL3RelayDnsState | 1.3.6.1.4.1.2272.1.201.1.3.3.2.1 | INTEGER | read-write | This object indicates DNS Relay function is enabled or disabled. |
| INT swL3RelayDnsStaticTableState | 1.3.6.1.4.1.2272.1.201.1.3.3.2.5 | INTEGER | read-write | This object indicates DNS Relay static table is enabled or disabled. |
| swL3RelayMgmt | 1.3.6.1.4.1.2272.1.201.1.3.3 | |||
| swL3RoutePrefEntry | 1.3.6.1.4.1.2272.1.201.1.3.8.1 | not-accessible | An entry of Ip Route Pref Table. | |
| INT swL3RoutePrefProtocol | 1.3.6.1.4.1.2272.1.201.1.3.8.1.1 | INTEGER | read-only | Protocol |
| swL3RoutePrefTable | 1.3.6.1.4.1.2272.1.201.1.3.8 | not-accessible | IP Route Pref table. | |
| INT swL3RoutePrefValue | 1.3.6.1.4.1.2272.1.201.1.3.8.1.2 | INTEGER | read-write | This value is a preference value for the given protocol. |
| INT swL3RouteRedistriDstProtocol | 1.3.6.1.4.1.2272.1.201.1.3.5.1.2 | INTEGER | read-only | Allows the selection of the protocol of the destination device. |
| swL3RouteRedistriEntry | 1.3.6.1.4.1.2272.1.201.1.3.5.1 | not-accessible | A list of information display the route redistribution table. | |
| INT swL3RouteRedistriMetric | 1.3.6.1.4.1.2272.1.201.1.3.5.1.4 | INTEGER | read-write | Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value. |
| INT swL3RouteRedistriSrcProtocol | 1.3.6.1.4.1.2272.1.201.1.3.5.1.1 | INTEGER | read-only | Allows the selection of the protocol of the source device. |
| INT swL3RouteRedistriState | 1.3.6.1.4.1.2272.1.201.1.3.5.1.5 | INTEGER | read-write | This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table. |
| swL3RouteRedistriTable | 1.3.6.1.4.1.2272.1.201.1.3.5 | not-accessible | Route redistribution allows routers on the network. That are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the vairous router��s routing tables and assinging appropriate metrics. This information is then exchanged among the various routers according to the individual routers current routing protocol. | |
| INT swL3RouteRedistriType | 1.3.6.1.4.1.2272.1.201.1.3.5.1.3 | INTEGER | read-write | Allows the selection of one of the methods for calcalculating the metric value. |
| swL3VrrpMgmt | 1.3.6.1.4.1.2272.1.201.1.3.7 | |||
| IP swL3VrrpOperCriticalIpAddr | 1.3.6.1.4.1.2272.1.201.1.3.7.1.1.2 | IpAddress | read-write | To make sure the ip interface connected by this virtual router is alive or not. |
| INT swL3VrrpOperCriticalIpState | 1.3.6.1.4.1.2272.1.201.1.3.7.1.1.3 | INTEGER | read-write | To enable or disable the feature of critical IP. |
| swL3VrrpOperEntry | 1.3.6.1.4.1.2272.1.201.1.3.7.1.1 | not-accessible | An entry in the swL3VrrpOperTable containing the operational characteristics of a virtual router. On a VRRP router, a given virtual router is identified by a combination of the IF index and VRID. | |
| INT swL3VrrpOperHoldDownTimer | 1.3.6.1.4.1.2272.1.201.1.3.7.1.1.4 | INTEGER | read-write | When VRRP is started, it need to spend this period of time to let the routing would be leared as well. The unit of this object is second. |
| swL3VrrpOperTable | 1.3.6.1.4.1.2272.1.201.1.3.7.1 | not-accessible | Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of 'swL3VrrpOperEntry' items. | |
| INT swL3VrrpOperVrId | 1.3.6.1.4.1.2272.1.201.1.3.7.1.1.1 | INTEGER | not-accessible | This object contains the Virtual Router Identifier (VRID). |
RFC description
Manages Layer 3 routing protocols including RIP, OSPF and relay services like BOOTP and DNS.
Start monitoring D-Link Layer 3 managed switch (IP interface/static route/ARP config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.