SILVERPEAK-MGMT-MIB

All MIBs › SILVERPEAK-MGMT-MIB

Organization: Silver Peak Systems, Inc.

Last Updated: 2012-01-06

Category: Silver Peak WAN Optimization, WAN and Routing

Description: Manages Silver Peak WAN optimization appliance tunnel configuration and traffic optimization policy.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is SILVERPEAK-MGMT-MIB?

SILVERPEAK-MGMT-MIB is Silver Peak Systems' proprietary MIB for managing and monitoring its WAN optimization/SD-WAN appliances. It exposes system identity data (software version, product model, serial number), overall operational status, system uptime, and a table of currently active alarms. It places strong emphasis on hardware/software health monitoring: spsSystemVersion tracks installed software version, spsSystemUptime confirms how long the appliance has been running since last reboot, spsOperStatus reports overall operational health, and spsActiveAlarmTable/spsActiveAlarmCount give a real-time view of active fault conditions with severity and name. It relies on its own private enterprise MIB tree (silverpeakMgmtMIBObjects/Notifications/Conformance) following standard SMIv2 conformance structure rather than importing heavily from external standard MIBs. It's deployed on Silver Peak WAN optimization/SD-WAN appliances at branch and data-center sites, polled by NMS platforms to track appliance health and active alarms. Engineers can download the SILVERPEAK-MGMT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in SILVERPEAK-MGMT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Silver Peak WAN optimization/SD-WAN appliance

Monitoring Examples

An operator polling spsOperStatus alongside spsActiveAlarmCount can immediately see whether the appliance is healthy or degraded; walking spsActiveAlarmTable by spsActiveAlarmIndex then reveals each active alarm's spsActiveAlarmSeverity and spsActiveAlarmName. Cross-referencing spsSystemUptime and spsSystemVersion helps determine whether a recent firmware upgrade or unplanned reboot coincided with the onset of the alarm condition.

What Can Be Monitored

system software version
system uptime
overall operational status
active alarm count and severity
system serial number/model

Imported Objects

From SILVERPEAK-SMI

silverpeakMgmt	OBJECT-IDENTITY
silverpeakNotifications	OBJECT-IDENTITY

From SILVERPEAK-TC

SilverpeakAlarmSeverity
SilverpeakSeqNum
SilverpeakYesNo

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString

How to Use in IPNetwork Monitor

Example using spsActiveAlarmCount OID:

Select a Silver Peak WAN optimization/SD-WAN appliance (system version/uptime/active-alarm status) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type spsActiveAlarmCount into the Find box to locate it in the OID tree, then select it and click OK. The number of active alarm entries in the alarm table - spsActiveAlarmTable, defined under silverpeakMgmtMIBTables subtree. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if the count changes from its expected baseline, since that would indicate the underlying set of items changed unexpectedly. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
silverpeakMgmtMIB	1.3.6.1.4.1.23867.3.1			This module defines the management variables used to manage and monitor appliance status.
silverpeakMgmtMIBObjects	1.3.6.1.4.1.23867.3.1.1
silverpeakMgmtMIBScalars	1.3.6.1.4.1.23867.3.1.1.1
STR spsSystemVersion	1.3.6.1.4.1.23867.3.1.1.1.1	DisplayString	read-only	System software version string
STR spsProductModel	1.3.6.1.4.1.23867.3.1.1.1.2	DisplayString	read-only	System product model
STR spsOperStatus	1.3.6.1.4.1.23867.3.1.1.1.3	DisplayString	read-only	The current operational state of the appliance.
INT spsActiveAlarmCountEx	1.3.6.1.4.1.23867.3.1.1.1.4	INTEGER	read-only	The number of active alarm entries in the alarm table - spsActiveAlarmTable, defined under silverpeakMgmtMIBTables subtree.
TIK spsSystemUptime	1.3.6.1.4.1.23867.3.1.1.1.5	TimeTicks	read-only	The amount of time in hundredth of a second since this NX was last initialized. Note that this is different from sysUpTime in the SNMPv2-MIB [RFC1907] because sysUpTime is the uptime of the network management portion of the system.
STR spsSystemSerial	1.3.6.1.4.1.23867.3.1.1.1.6	DisplayString	read-only	System serial number string
silverpeakMgmtMIBTables	1.3.6.1.4.1.23867.3.1.1.2
spsActiveAlarmTable	1.3.6.1.4.1.23867.3.1.1.2.1		not-accessible	A list of the active alarm entries. This represents the fault conditions that are still active in the appliance.
activeAlarmEntry	1.3.6.1.4.1.23867.3.1.1.2.1.1		not-accessible	The active alarm entries that are still valid system faults.
INT spsActiveAlarmIndex	1.3.6.1.4.1.23867.3.1.1.2.1.1.1	INTEGER	not-accessible	An index that uniquely identifies an entry in the active alarm table.
SIL spsActiveAlarmSeqNum	1.3.6.1.4.1.23867.3.1.1.2.1.1.2	SilverpeakSeqNum	read-only	The active alarm's sequence number at the time it was generated.
SIL spsActiveAlarmSeverity	1.3.6.1.4.1.23867.3.1.1.2.1.1.3	SilverpeakAlarmSeverity	read-only	The alarm severity for the active alarm.
STR spsActiveAlarmName	1.3.6.1.4.1.23867.3.1.1.2.1.1.4	DisplayString	read-only	A short name for the active alarm.
STR spsActiveAlarmDescr	1.3.6.1.4.1.23867.3.1.1.2.1.1.5	DisplayString	read-only	A description for the active alarm.
STR spsActiveAlarmSource	1.3.6.1.4.1.23867.3.1.1.2.1.1.6	DisplayString	read-only	The source for the active alarm.
STR spsActiveAlarmType	1.3.6.1.4.1.23867.3.1.1.2.1.1.7	DisplayString	read-only	The alarm type for the active alarm.
SIL spsActiveAlarmAcked	1.3.6.1.4.1.23867.3.1.1.2.1.1.8	SilverpeakYesNo	read-only	Identifies if the user has acknowledged the alarm.
SIL spsActiveAlarmActive	1.3.6.1.4.1.23867.3.1.1.2.1.1.9	SilverpeakYesNo	read-only	Identifies if the alarm is currently active.
SIL spsActiveAlarmClearable	1.3.6.1.4.1.23867.3.1.1.2.1.1.10	SilverpeakYesNo	read-only	Identifies if the user can manually clear the alarm.
OCT spsActiveAlarmLogTime	1.3.6.1.4.1.23867.3.1.1.2.1.1.11	OCTET STRING	read-only	The value of sysUpTime when the alarm was generated.
SIL spsActiveAlarmServiceAffect	1.3.6.1.4.1.23867.3.1.1.2.1.1.12	SilverpeakYesNo	read-only	Identifies if the alarm is service affecting.
INT spsActiveAlarmTypeId	1.3.6.1.4.1.23867.3.1.1.2.1.1.13	INTEGER	read-only	An ID that uniquely identifies a type of alarm. The following is a list of currently defined type IDs (ID listed below is in hexadecimal): ID Description ----- ------------------------------------------ 10000 Tunnel remote ID is misconfigured 10001 Tunnel state is Down 10002 Tunnel VRRP IP is misconfigured 10003 Tunnel keepalive version mismatch 10004 Tunnel WCCP GID is misconfigured 10005 Tunnel software version mismatch 10006 Connecting to a non-VX-X is not supported. Please contact sales@silver-peak.com to discuss your options. 10007 Duplicate Silver Peak license detected on peer device. 10008 Tunnel local IP address not owned by this appliance 10009 Tunnel software version mismatch results in reduced functionality. 1000a Tunnel peer encapsulation mode mismatch detected. 1000b UDP Destination Port is the same as flow redirection port 20000 Tunnel has unexpected traffic class error 30000 RAID array is degraded 30001 Disk is failed 30002 Disk is degraded 30003 Fan failure detected 30004 System bypass mode 30005 LAN/WAN fail-to-wire card failure 30006 LAN/WAN fail-to-wire card relay failure 30007 Encryption card hardware failure 30008 Network interface admin down 30009 Network interface link down 3000a Management interface link down 3000b Interface is half duplex 3000c Interface speed is 10 Mbps 3000d Config DB disk full 3000e Operating System disk full 3000f File system disk full 30010 Datapath internal loopback test failed 30011 WAN next-hop unreachable 30012 VRRP instance is down 30013 VRRP state changed from Master to Backup 30014 WAN next-hop router discovered on a LAN port (box is in backwards) 30015 Disk is not in service 30016 Disk is rebuilding 30017 Disk removed by operator 30018 LAN/WAN interfaces have different admin states 30019 LAN/WAN interfaces have different link carrier states 3001a LAN/WAN interface has been shutdown due to link propagation of paired interface 3001b Disk SMART threshold exceeded 3001c Flow redirection cluster peer is down 3001d Bonding members have different speed/duplex 3001e WCCP adjacency(ies) down 3001f WCCP assignment table mismatch 30020 Power supply not connected, not powered or failed 30021 NIC interface failure 30022 LAN next-hop unreachable 30023 Unexpected system restart 30024 Insufficient configured memory size for this virtual appliance 30025 Insufficient configured processor count for this virtual appliance 30026 Insufficient configured disk storage for this virtual appliance 30027 Interfaces have different MTUs 30028 Interfaces have different MTUs 30029 Bridge loop is detected 3002a Bridge creation failed 3002b Network interface is unassigned 3002c System optimization turned off 3002d Sub-optimal configured memory size for this virtual appliance 3002e Sub-optimal configured processor count for this virtual appliance 3002f Sub-optimal configured disk storage for this virtual appliance 40000 Software upgrade process has failed 40001 System is low on resources 40002 Significant change in time of day has occurred, and might compromise statistics. 40003 The licensing for this virtual appliance has expired. 40004 There is no license installed on this virtual appliance. 40005 A disk self test has been performed. The system will require a reboot after the test. 40006 The SSL private key is invalid. 40007 The SSL certificate is not yet valid. 40008 The SSL certificate has expired. 40009 The NTP server is unreachable. 4000a Virtual appliance license expires on yyyy/mm/dd. 4000b Virtual appliance license expires on yyyy/mm/dd. 4000c Invalid virtual appliance license. 4000d Dual Wan-nexthop topology configuration no longer supported. 4000e Setting system wan-nexthop to VLAN nhop is no longer necessary. 4000f Minor inconsistencies during QOS upgrade. 40010 Major inconsistencies during QOS upgrade. 40011 Tunnel IP hdr disable setting was discarded during upgrade. 40012 A very large range has been configured for a local subnet. 40013 A peer name has been specified in a route-map that can't be resolved. 40014 Shaper max bandwidth exceeds system bandwidth 40015 Software capability token exceeds warning threshold 40016 Software capability token has exceeded the required limit 40017 Silvepeak Portal is unreachable 40018 Silverpeak Portal is unreachable for setting up a remote help session 40019 An application has been deleted on the Silver Peak portal 4001a Boost Limiting MTS 4001b Bad portal registration data 4001c EdgeConnect Base license not granted 4001d Orchestrator is unreachable from appliance using HTTPS 4001e Silver Peak Portal is unreachable for licensing 4001f Silver Peak Portal hostname cannot be resolved 40020 Edge Connect Plus license not granted 40021 Edge Connect Boost license not granted 40022 Appliance has not been approved for licensing by Orchestrator 40023 Software capability token related alarm 40024 A NATed interface connected to Internet has no public IP address 40025 Initial admin password is not yet changed 40026 DHCP server mis-configuration 40027 Subnet table has exceeded high-water level for BGP/OSPF entries 40028 Subnet table has reached maximum capacity 40029 Unable to resolve Orchestrator DNS name 4002a Builtin CA certificate is not valid 4002b CA certificate Bundle is not valid 4002c A BGP peer session is no longer in Established state 4002d An IP SLA monitor is in Down state 4002e An OSPF neighbor session is no longer in Full state 4002f DNS Proxy is down 40030 EC Licensing Warning 50001 WAN-side transmit throughput TCA 50002 LAN-side receive throughput TCA 50003 Total number of optimized flows TCA 50004 Total number of flows TCA 50005 File-system utilization TCA 50006 Tunnel latency TCA 50007 Tunnel loss pre-FEC TCA 50008 Tunnel loss post-FEC TCA 50009 Tunnel OOP pre-POC TCA 5000a Tunnel OOP post-POC TCA 5000b Tunnel utilization TCA 5000c Tunnel reduction TCA 5000d Appliance capacity TCA ----- ------------------------------------------
silverpeakMgmtMIBConformance	1.3.6.1.4.1.23867.3.1.2
silverpeakMgmtMIBCompliances	1.3.6.1.4.1.23867.3.1.2.1
silverpeakMgmtCompliance	1.3.6.1.4.1.23867.3.1.2.1.1			The compliance statement for agents implementing silverpeakMgmtMIB.
silverpeakMgmtMIBGroups	1.3.6.1.4.1.23867.3.1.2.2
silverpeakMgmtGroup	1.3.6.1.4.1.23867.3.1.2.2.1			A collection of objects used to retrieve management information from Silverpeak Systems appliances.
silverpeakMgmtNotifyGroup	1.3.6.1.4.1.23867.3.1.2.2.3			A collection of the Notifications supported in the management MIB.
silverpeakMgmtMIBNotifications	1.3.6.1.4.1.23867.4.1
NTF spsNotifyAlarm	1.3.6.1.4.1.23867.4.1.1			A notification that the system has just generated and alarm.

RFC description

Management and monitoring of Silver Peak Systems appliance status, system version, product model, and operational state.

Start monitoring Silver Peak WAN optimization/SD-WAN appliance (system version/uptime/active-alarm status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download SILVERPEAK-MGMT-MIB