REDLINE-SYSTEM-MIB

All MIBs › REDLINE-SYSTEM-MIB

Organization: Redline Communications Inc.

Last Updated: 2005-03-31

Category: Wireless and Radio

Description: Manages system-level configuration and status for Redline Communications WiMAX devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is REDLINE-SYSTEM-MIB?

REDLINE-SYSTEM-MIB provides Redline Communications' vendor extensions to the standard SNMPv2 MIB System Group, adding system-level configuration and status objects for its WiMAX wireless broadband devices. It exposes objects covering device identity (serial number), reboot control, and networking configuration such as DHCP server address, static IP/subnet/gateway, and remote syslog server address. Its monitoring value lies in tracking core software/system status, confirming the device's serial number for asset tracking, verifying reboot events, and confirming that IP addressing and syslog forwarding configuration are correct and unchanged, which helps detect unexpected reboots or configuration drift. It explicitly extends the standard SNMPv2-MIB System Group (sysDescr/sysUpTime), so it depends on and complements that IETF standard rather than replacing it. It is typically deployed alongside other Redline product MIBs by WISPs managing Redline WiMAX base stations and subscriber units, making REDLINE-SYSTEM-MIB SNMP monitoring a routine part of tracking asset identity and configuration drift across the network.

IPNetwork Monitor allows you to monitor SNMP objects defined in REDLINE-SYSTEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Redline Communications WiMAX base station/subscriber unit

Monitoring Examples

An operator can poll redlineSystemSerialNumber to confirm asset identity of a deployed unit, and monitor redlineSystemSystemReboot to detect whether the device was recently rebooted (planned or unplanned), which would explain a temporary service interruption. Checking redlineSystemIpAddress, redlineSystemSubnetMask, and redlineSystemDefGatewayAddress against expected values helps catch IP misconfiguration that could isolate the device from management access. redlineSystemSyslogServerIpAddress verifies that the unit is still forwarding log events to the correct central syslog collector.

What Can Be Monitored

device serial number
reboot status/control
IP address/subnet/gateway configuration
DHCP server address
syslog server destination

Imported Objects

From INET-ADDRESS-MIB

InetAddress
InetAddressType
InetPortNumber

From REDLINE-MIB

redlineSystem

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
NTF redlineSWUpgradeStatusTrap	1.3.6.1.4.1.10728.2.1.1.4.3.1			Event that reports SW Upgrade progress and status changes.
redlineSystemAccessControlObjects	1.3.6.1.4.1.10728.2.1.1.5
redlineSystemAccessCtrlEntry	1.3.6.1.4.1.10728.2.1.1.5.5.1		not-accessible	This entry contains privacy information about a host allowed to access the system.
U32 redlineSystemAccessCtrlIndex	1.3.6.1.4.1.10728.2.1.1.5.5.1.1	Unsigned32	not-accessible	The index of the Snmp Access Control table.
IP redlineSystemAccessCtrlManagerIpAddr	1.3.6.1.4.1.10728.2.1.1.5.5.1.3	InetAddress	read-create	The INET address of the host allowed to access the system.
IPt redlineSystemAccessCtrlManagerIpAddrType	1.3.6.1.4.1.10728.2.1.1.5.5.1.2	InetAddressType	read-create	The INET address type of the host allowed to access the system. IPv4 type supported only.
STR redlineSystemAccessCtrlReadCommunity	1.3.6.1.4.1.10728.2.1.1.5.5.1.4	DisplayString	read-create	The read community string associated with redlineSystemAccessCtrlManagerIpAddress.
ROW redlineSystemAccessCtrlStatus	1.3.6.1.4.1.10728.2.1.1.5.5.1.6	RowStatus	read-create	This object is used to create and delete rows in the redlineSystemTrapReceiverTable table. Only the 'createAndGo' and 'destroy' values can be specified in a set operation when an entry is created or destroyed, respectively.
redlineSystemAccessCtrlTable	1.3.6.1.4.1.10728.2.1.1.5.5		not-accessible	This table contains a list of hosts which are allowed to access the system. Each entry associated with the host, has ip address and read and write passwords. Only hosts identified by a right combination of ipAddress and password will be allowed to access the system. An entry can contain Ip address of '0.0.0.0'. In which case all hosts using password associated with this address will be granted access to the system. Initially, the table will contain only one entry with Ip address set to '0.0.0.0', read community set to 'public' and write community set to 'private'. The maximum number of entries in this table is eight
STR redlineSystemAccessCtrlWriteCommunity	1.3.6.1.4.1.10728.2.1.1.5.5.1.5	DisplayString	read-create	The write community string associated with redlineSystemAccessCtrlManagerIpAddress.
redlineSystemBasicGroup	1.3.6.1.4.1.10728.2.1.1.6.1.1			Basic objects.
redlineSystemCompliance	1.3.6.1.4.1.10728.2.1.1.6.2.1			The compliance statement for SNMP entities that implement this MIB module.
redlineSystemCompls	1.3.6.1.4.1.10728.2.1.1.6.2
INT redlineSystemConfigBackupConfigType	1.3.6.1.4.1.10728.2.1.1.3.1.1.2	INTEGER	read-create	Specifies the type of configuration to be backup.
redlineSystemConfigBackupEntry	1.3.6.1.4.1.10728.2.1.1.3.1.1		not-accessible	This entry contains information about a current or last configuration backup.
STR redlineSystemConfigBackupFailureReason	1.3.6.1.4.1.10728.2.1.1.3.1.1.9	DisplayString	read-only	The short explanation of why configuration backup failed. In a case of success this object will contain empty string.
IP redlineSystemConfigBackupFtpAddress	1.3.6.1.4.1.10728.2.1.1.3.1.1.4	InetAddress	read-create	The INET address of the FTP server.
IPt redlineSystemConfigBackupFtpAddressType	1.3.6.1.4.1.10728.2.1.1.3.1.1.3	InetAddressType	read-create	The INET address type of the configuration backup FTP server. IPv4 type supported only.
STR redlineSystemConfigBackupFtpFile	1.3.6.1.4.1.10728.2.1.1.3.1.1.7	DisplayString	read-create	The full software image file path name as required by the FTP server.
STR redlineSystemConfigBackupFtpPassword	1.3.6.1.4.1.10728.2.1.1.3.1.1.6	DisplayString	read-create	The FTP user password. After this object is created it is not accessible.
STR redlineSystemConfigBackupFtpUser	1.3.6.1.4.1.10728.2.1.1.3.1.1.5	DisplayString	read-create	The FTP user name.
INT redlineSystemConfigBackupIndex	1.3.6.1.4.1.10728.2.1.1.3.1.1.1	INTEGER	not-accessible	The index of the software download table. The only value allowed is 1.
INT redlineSystemConfigBackupStatus	1.3.6.1.4.1.10728.2.1.1.3.1.1.8	INTEGER	read-only	The status of the current or last configuration backup.
redlineSystemConfigBackupTable	1.3.6.1.4.1.10728.2.1.1.3.1		not-accessible	This table contains at most one entry representing a configuration backup process that is either currently in progress or one that was completed. A management station can create this entry if and only if either the table is empty or the only entry is for a backup that has already been completed. An attempt to create or write this entry when a backup is already in progress results in the 'resourceUnavailable' error status.
INT redlineSystemConfigRestoreConfigType	1.3.6.1.4.1.10728.2.1.1.3.2.1.2	INTEGER	read-create	Specifies the type of configuration to be restored.
redlineSystemConfigRestoreEntry	1.3.6.1.4.1.10728.2.1.1.3.2.1		not-accessible	This entry contains information about a current or last configuration restore.
STR redlineSystemConfigRestoreFailureReason	1.3.6.1.4.1.10728.2.1.1.3.2.1.9	DisplayString	read-only	The short explanation of why configuration restore failed. In a case of success this object will contain empty string.
IP redlineSystemConfigRestoreFtpAddress	1.3.6.1.4.1.10728.2.1.1.3.2.1.4	InetAddress	read-create	The INET address of the FTP server.
IPt redlineSystemConfigRestoreFtpAddressType	1.3.6.1.4.1.10728.2.1.1.3.2.1.3	InetAddressType	read-create	The INET address type of the configuration restore FTP server. IPv4 type supported only.
STR redlineSystemConfigRestoreFtpFile	1.3.6.1.4.1.10728.2.1.1.3.2.1.7	DisplayString	read-create	The full software image file path name as required by the FTP server.
STR redlineSystemConfigRestoreFtpPassword	1.3.6.1.4.1.10728.2.1.1.3.2.1.6	DisplayString	read-create	The FTP user password. After this object is created it is not accessible.
STR redlineSystemConfigRestoreFtpUser	1.3.6.1.4.1.10728.2.1.1.3.2.1.5	DisplayString	read-create	The FTP user name.
INT redlineSystemConfigRestoreIndex	1.3.6.1.4.1.10728.2.1.1.3.2.1.1	INTEGER	not-accessible	The index of the software download table. The only value allowed is 1.
INT redlineSystemConfigRestoreStatus	1.3.6.1.4.1.10728.2.1.1.3.2.1.8	INTEGER	read-only	The status of the current or last configuration restore.
redlineSystemConfigRestoreTable	1.3.6.1.4.1.10728.2.1.1.3.2		not-accessible	This table contains at most one entry representing a configuration restore process that is either currently in progress or one that was completed. A management station can create this entry if and only if either the table is empty or the only entry is for a restore that has already been completed. An attempt to create or write this entry when a restore is already in progress results in the 'resourceUnavailable' error status. After the process is finished with the status set to 'success', then (and only then) the system will be automatically rebooted in order for the newly restored parameters to become active.
redlineSystemConfigurationObjects	1.3.6.1.4.1.10728.2.1.1.3
redlineSystemConformance	1.3.6.1.4.1.10728.2.1.1.6
IP redlineSystemDefGatewayAddress	1.3.6.1.4.1.10728.2.1.1.1.4.6	InetAddress	read-write	The INET address of the default gateway. Note: This object can not be set if usage of DHCP server is enabled. An attempt to set the address will fail and return 'resourceUnavailable' error
IPt redlineSystemDefGatewayAddressType	1.3.6.1.4.1.10728.2.1.1.1.4.5	InetAddressType	read-write	The INET address type of the default gateway. IPv4 type supported only.
IP redlineSystemDHCPServerIpAddress	1.3.6.1.4.1.10728.2.1.1.1.3.2	InetAddress	read-write	The INET address of DHCP server. Note: This object can not be set if usage of DHCP server is disabled. An attempt to set the address will fail and return 'resourceUnavailable' error
IPt redlineSystemDHCPServerIpAddressType	1.3.6.1.4.1.10728.2.1.1.1.3.1	InetAddressType	read-write	The INET address type of Ip address of DHCP server. IPv4 type supported only.
redlineSystemGroups	1.3.6.1.4.1.10728.2.1.1.6.1
IP redlineSystemIpAddress	1.3.6.1.4.1.10728.2.1.1.1.4.2	InetAddress	read-write	The INET address of the system. Note: This object can not be set if usage of DHCP server is enabled. An attempt to set the address will fail and return 'resourceUnavailable' error
IPt redlineSystemIpAddressType	1.3.6.1.4.1.10728.2.1.1.1.4.1	InetAddressType	read-write	The INET address type of Ip address of the system. IPv4 type supported only.
redlineSystemMib	1.3.6.1.4.1.10728.2.1.1			This MIB module contains Redline extensions to the SNMPv2 MIB System Group.
redlineSystemNotificationGroup	1.3.6.1.4.1.10728.2.1.1.6.1.2
redlineSystemNotificationObjects	1.3.6.1.4.1.10728.2.1.1.4
NTF redlineSystemPingTrap	1.3.6.1.4.1.10728.2.1.1.4.3.999			A ping trap notification.
INT redlineSystemPingTrapTrigger	1.3.6.1.4.1.10728.2.1.1.4.1.999	INTEGER	read-write	Causes a ping trap to be sent
STR redlineSystemSerialNumber	1.3.6.1.4.1.10728.2.1.1.1.1	DisplayString	read-only	The serial number of the unit.
redlineSystemSoftwareObjects	1.3.6.1.4.1.10728.2.1.1.2
IP redlineSystemSubnetMask	1.3.6.1.4.1.10728.2.1.1.1.4.4	InetAddress	read-write	The Subnet Mask of the system. Note: This object can not be set if usage of DHCP server is enabled. An attempt to set the address will fail and return 'resourceUnavailable' error
IPt redlineSystemSubnetMaskAddressType	1.3.6.1.4.1.10728.2.1.1.1.4.3	InetAddressType	read-write	The INET address type of subnet mask of the system. IPv4 type supported only.
INT redlineSystemSwActivateAlternate	1.3.6.1.4.1.10728.2.1.1.2.3	INTEGER	read-write	Setting this to 2 triggers the switch-over to the alternate s/w image and reboot of the system. Before the switch-over a validation of the alternate image is performed and if it fails the 'inconsistentValue' error status is returned.
STR redlineSystemSwActiveVersion	1.3.6.1.4.1.10728.2.1.1.2.1	DisplayString	read-only	The s/w version of the active (running) image.
STR redlineSystemSwAlternateVersion	1.3.6.1.4.1.10728.2.1.1.2.2	DisplayString	read-only	The s/w version of the alternate (non-active) image.
redlineSystemSwDownloadEntry	1.3.6.1.4.1.10728.2.1.1.2.5.1		not-accessible	This entry contains information about a current or last software download.
STR redlineSystemSwDownloadFailureReason	1.3.6.1.4.1.10728.2.1.1.2.5.1.9	DisplayString	read-only	The short explanation of why software download failed. In a case of success this object will contain empty string.
IP redlineSystemSwDownloadFtpAddress	1.3.6.1.4.1.10728.2.1.1.2.5.1.3	InetAddress	read-create	The INET address of the FTP server.
IPt redlineSystemSwDownloadFtpAddressType	1.3.6.1.4.1.10728.2.1.1.2.5.1.2	InetAddressType	read-create	The INET address type of the software upgrade FTP server. IPv4 type supported only.
STR redlineSystemSwDownloadFtpFile	1.3.6.1.4.1.10728.2.1.1.2.5.1.6	DisplayString	read-create	The full software image file path name as required by the FTP server.
STR redlineSystemSwDownloadFtpPassword	1.3.6.1.4.1.10728.2.1.1.2.5.1.5	DisplayString	read-create	The FTP user password. After this object is created it is not accessible.
STR redlineSystemSwDownloadFtpUser	1.3.6.1.4.1.10728.2.1.1.2.5.1.4	DisplayString	read-create	The FTP user name.
INT redlineSystemSwDownloadIndex	1.3.6.1.4.1.10728.2.1.1.2.5.1.1	INTEGER	not-accessible	The index of the software download table. The only value allowed is 1.
INT redlineSystemSwDownloadProgress	1.3.6.1.4.1.10728.2.1.1.4.2.1	INTEGER	accessible-for-notify	The software download progress states.
INT redlineSystemSwDownloadStatus	1.3.6.1.4.1.10728.2.1.1.2.5.1.7	INTEGER	read-only	The status of the current or last software download.
redlineSystemSwDownloadTable	1.3.6.1.4.1.10728.2.1.1.2.5		not-accessible	This table contains at most one entry representing a software download process that is either currently in progress or one that was completed. A management station can create this entry if and only if either the table is empty or the only entry is for a download that has already been completed. An attempt to create or write this entry when a download is already in progress results in the 'resourceUnavailable' error status. The redlineSystemSwDownloadStatus state object is used to control and monitor a s/w download process. Setting it to the 'download' value starts a new download if none is active at the time (otherwise an error status is returned).
DAT redlineSystemSwDownloadTimeEnded	1.3.6.1.4.1.10728.2.1.1.2.5.1.8	DateAndTime	read-only	The date and time this software download finished.
INT redlineSystemSwSyncAlternate	1.3.6.1.4.1.10728.2.1.1.2.4.1.2	INTEGER	read-write	Setting it to 2 will synchronize the alternate s/w image and configuration database, i.e. the active s/w image and the active configuration are copied to the alternate s/w image and configuration, respectively.
redlineSystemSwSyncAlternateEntry	1.3.6.1.4.1.10728.2.1.1.2.4.1		not-accessible	This entry contains information about a current or last software synchronization.
INT redlineSystemSwSyncAlternateIndex	1.3.6.1.4.1.10728.2.1.1.2.4.1.1	INTEGER	not-accessible	The index of the software isynchronization table. The only value allowed is 1.
INT redlineSystemSwSyncAlternateStatus	1.3.6.1.4.1.10728.2.1.1.2.4.1.3	INTEGER	read-only	The status of the current or last software synchronization.
redlineSystemSwSyncAlternateTable	1.3.6.1.4.1.10728.2.1.1.2.4		not-accessible	This table contains at most one entry representing a software synchronization process that is either currently in progress or one that was completed. When requested synchronization,the active s/w i image and the active configuration are copied to the alternate s/w image and configuration, respectively. A management station can create this entry if and only if either the table is empty or the only entry is for a synchronization that has already been completed. An attempt to create or write this entry when a synchronization is already in progress results in the 'resourceUnavailable' error status. The redlineSystemSwSyncAlternateStatus state object is used to control and monitor a s/w synchronization process. Setting it to the 'synchronizeAlternate' value starts a new synchronization if none is active at the time (otherwise an error status is returned).
DAT redlineSystemSwSyncAlternateTimeEnded	1.3.6.1.4.1.10728.2.1.1.2.4.1.4	DateAndTime	read-only	The date and time this software synchronization finished.
redlineSystemSysControl	1.3.6.1.4.1.10728.2.1.1.1.2
redlineSystemSysDhcpObjects	1.3.6.1.4.1.10728.2.1.1.1.3
redlineSystemSysIpObjects	1.3.6.1.4.1.10728.2.1.1.1.4
IP redlineSystemSyslogServerIpAddress	1.3.6.1.4.1.10728.2.1.1.1.5.2	InetAddress	read-write	The INET address of Syslog server. Note: Entering '0.0.0.0' as an address will indicate to the system that Syslog capability is not to be used.
IPt redlineSystemSyslogServerIpAddressType	1.3.6.1.4.1.10728.2.1.1.1.5.1	InetAddressType	read-write	The INET address type of Ip address of Syslog server. IPv4 type supported only.
redlineSystemSysSyslogObjects	1.3.6.1.4.1.10728.2.1.1.1.5
redlineSystemSystemObjects	1.3.6.1.4.1.10728.2.1.1.1
INT redlineSystemSystemReboot	1.3.6.1.4.1.10728.2.1.1.1.2.1	INTEGER	read-write	Setting this variable to 2 causes a reboot of the system.
redlineSystemTrapActivationEntry	1.3.6.1.4.1.10728.2.1.1.4.1.2.1		not-accessible	This entry contains information about trap acgtivation state.
redlineSystemTrapActivationTable	1.3.6.1.4.1.10728.2.1.1.4.1.2		not-accessible	This table contains information about trap activation in the system i.e. the trap generation can be enabled or disabled. The entries of this table are indexed by the trap OID.
redlineSystemTrapControl	1.3.6.1.4.1.10728.2.1.1.4.1
redlineSystemTrapDefinitions	1.3.6.1.4.1.10728.2.1.1.4.3
INT redlineSystemTrapEnable	1.3.6.1.4.1.10728.2.1.1.4.1.2.1.2	INTEGER	read-write	Indicates whether the system is permitted to generate traps specified by this entry.
OID redlineSystemTrapObjectID	1.3.6.1.4.1.10728.2.1.1.4.1.2.1.1	OBJECT IDENTIFIER	not-accessible	Identifies the trap which generation is to be controlled by this entry.
redlineSystemTrapObjects	1.3.6.1.4.1.10728.2.1.1.4.2
IP redlineSystemTrapReceiverAddress	1.3.6.1.4.1.10728.2.1.1.4.1.1.1.3	InetAddress	read-create	The INET address of the trap receiver.
IPt redlineSystemTrapReceiverAddressType	1.3.6.1.4.1.10728.2.1.1.4.1.1.1.2	InetAddressType	read-create	The INET address type of the trap receiver.
STR redlineSystemTrapReceiverCommunity	1.3.6.1.4.1.10728.2.1.1.4.1.1.1.5	DisplayString	read-create	The community string of the trap receiver.
redlineSystemTrapReceiverEntry	1.3.6.1.4.1.10728.2.1.1.4.1.1.1		not-accessible	This entry contains information about a provisioned trap receiver (a trap destination from the agent's point of view.
U32 redlineSystemTrapReceiverIndex	1.3.6.1.4.1.10728.2.1.1.4.1.1.1.1	Unsigned32	not-accessible
INE redlineSystemTrapReceiverPort	1.3.6.1.4.1.10728.2.1.1.4.1.1.1.4	InetPortNumber	read-create	The UDP port of the trap receiver.
ROW redlineSystemTrapReceiverStatus	1.3.6.1.4.1.10728.2.1.1.4.1.1.1.6	RowStatus	read-create	This object is used to create and delete rows in the redlineSystemTrapReceiverTable table. Only the 'createAndGo' and 'destroy' values can be specified in a set operation when an entry is created or destroyed, respectively.
redlineSystemTrapReceiverTable	1.3.6.1.4.1.10728.2.1.1.4.1.1		not-accessible	This table contains information about provisioned trap receivers i.e. the trap receivers that this agent will send notifications to. The entries of this table are indexed by their IP address and port values. The maximum number of entries in this table is eight.

RFC description

Redline Communications system extensions for device serial number, reboot control, and DHCP configuration.

Start monitoring Redline Communications WiMAX base station/subscriber unit (SNMPv2 System Group extensions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download REDLINE-SYSTEM-MIB

What Is REDLINE-SYSTEM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description