| OID symbolic | OID numeric | Type | Access | Description |
|---|
| xdslIfConfigMIBObjects | 1.3.6.1.4.1.1795.2.24.9.2 | | | |
| xdslDevGenericIfConfig | 1.3.6.1.4.1.1795.2.24.9.2.1 | | | |
| xdslDevGenericIfConfigTable | 1.3.6.1.4.1.1795.2.24.9.2.1.1 | | not-accessible | The xdslDevGenericIfConfigTable provides config information
generic to a xDSL device, or system. The table is indexed by an
object which corresponds to ifIndex. These ifIndex entries,
themselves, denote and identify specific xdsl interfaces on
the board or module. Also the configuration parameters are
grouped into two broad categories, 'up' and 'down'. 'up'
reflects the upstream direction (from the customer premises
to the central office). 'Down' reflects the downstream
direction (from the central office to the customer premises) |
| xdslDevGenericIfConfigEntry | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1 | | not-accessible | Describes a specific xDSL interface entry. |
| INT xdslDevGenericIfConfigPortSpeedBehaviour | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.1 | INTEGER | read-write | The value of this object corresponds to the
behaviour of the specified port. The default
value for this object is fixed (1). |
| INT xdslDevGenericIfConfigMarginThreshold | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.2 | INTEGER | read-write | The value of this object corresponds to the offset from
the startup margin. The threshold margin is calculated
by subtracting the offset from the startup margin.
Permissible range of values are between -7 and 14.
A value of -9999 disables the threshold check. The default
value of this object is 3 |
| STR xdslDevGenericIfConfigPortID | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.3 | DisplayString | read-write | The value of this object corresponds to 40 character
information only field that identifies what the DSL
port is connected to (Circuit ID, MDF location,
Customer name, etc.) |
| INT xdslDevGenericIfConfigLinkUpDownTransitionThreshold | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.4 | INTEGER | read-write | The value of this object corresponds to the threshold
value for link up-down transitions. If link up-down's exceed
this threshold value a xdslLinkupDownTransitions
trap is generated. This value would represent the number
of link up-down transitions in a 15 minute interval. A value
of -9999 disables the threshold check. The default value for this
object is 0 |
| INT xdslDevGenericIfConfigLineEncodeType | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.5 | INTEGER | read-only | The value of this object corresponds to the line
encoding technology used for data transmission over
the the dsl link. |
| INT xdslDevGenericIfConfigLineRateMode | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.6 | INTEGER | read-write | The value of this object is used to choose the line
rate list for data transmission over the dsl link.
The default value is standard(1). |
| xdslDevRADSLSpecificIfConfig | 1.3.6.1.4.1.1795.2.24.9.2.2 | | | |
| xdslDevRADSLSpecificIfConfigTable | 1.3.6.1.4.1.1795.2.24.9.2.2.1 | | not-accessible | The xdslDevRADSLSpecificIfConfigTable provides config information
specific to a xDSL device, or system. The table is indexed by
an object which corresponds to ifIndex. These ifIndex entries,
themselves, denote and identify specific xdsl interfaces on
the board or module. Also the configuration parameters are
grouped into two broad categories, 'up' and 'down'. 'up'
reflects the upstream direction (from the customer premises
to the central office). 'Down' reflects the downstream
direction (from the central office to the customer premises) |
| xdslDevRADSLSpecificIfConfigEntry | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1 | | not-accessible | Describes a specific xDSL interface entry. |
| INT xdslDevRADSLSpecificIfConfigUpFixedPortSpeed | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.1 | INTEGER | read-write | The value of this object corresponds to the upstream
speed of the specified port for fixed port speed
behaviour. All the speeds are in kbps.
If the port speed behaviour is adaptive an error
of noSuchName will be returned by the agent. |
| INT xdslDevRADSLSpecificIfConfigDownFixedPortSpeed | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.2 | INTEGER | read-write | The value of this object corresponds to the downstream
speed of the specified port for fixed port speed
behaviour. All the speeds are in kbps.
If the port speed behaviour is adaptive an error of noSuchName
will be returned by the agent. |
| INT xdslDevRADSLSpecificIfConfigUpAdaptiveUpperBoundPortSpeed | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.3 | INTEGER | read-write | The value of this object corresponds to the
upper bound for the upstream port speed of the specified port
for adaptive port speed behaviour. The speeds are measured
in kbps. If the port speed behaviour is fixed
an error of noSuchName will be returned by the agent. |
| INT xdslDevRADSLSpecificIfConfigUpAdaptiveLowerBoundPortSpeed | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.4 | INTEGER | read-write | The value of this object corresponds to the
lower bound for the upstream port speed of the
specified port for adaptive port speed behaviour
in kbps. If the port speed behaviour is fixed an
error of noSuchName will be returned by the agent.
The value -9999 should be used to disable the lower
bound threshold check. The default value for this
object is -9999 |
| INT xdslDevRADSLSpecificIfConfigDownAdaptiveUpperBoundPortSpeed | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.5 | INTEGER | read-write | The value of this object corresponds to
the upper bound allowed for the downstream port speed
of the specified port for adaptive port speed
behaviour. The speeds are measured in kbps.
If the port speed behaviour is fixed an error of noSuchName
will be returned by the agent. |
| INT xdslDevRADSLSpecificIfConfigDownAdaptiveLowerBoundPortSpeed | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.6 | INTEGER | read-write | The value of this object corresponds to the
Minimum lower bound allowed for the downstream port speed
of the specified port for adaptive port speed behaviour.
If the port speed behaviour is fixed an error of noSuchName
will be returned by the agent. The speeds are measured in kbps.
The value -9999 is used to disable the lower bound threshold
check.The default value for this object is -9999 |
| INT xdslDevRADSLSpecificIfConfigReedSolomonDownFwdErrCorrection | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.7 | INTEGER | read-write | The value of this object corresponds to the
Reed-Solomon forward error correction in the downstream
direction. The default value of this object should be
minimizeError (1). |
| INT xdslDevRADSLSpecificIfConfigStartUpMargin | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.8 | INTEGER | read-write | The value of this object corresponds to the startup value
of the margin for a DSL interface (specified by ifIndex).
The unit is db (decibels. The higher the margin the better
the quality of the line. The default value of this object is 3. |
| INT xdslDevRADSLSpecificIfConfigTxPowerAttenuation | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.9 | INTEGER | read-write | This value corresponds to the Transmitt Power Attenuation in
dB for the access node. This value represents the downstream
power level in dB. Permissible values are -6, -3 and 0.
The default value of this object is 0 dB. The power levels +3
and +6 may be used in future. |
| INT xdslDevRADSLSpecificIfConfigSnTxPowerAttenuation | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.10 | INTEGER | read-write | This value corresponds to the Transmitt Power Attenuation in dB
for the service node. This value represents the upstream power
level in dB. Permissible values are -9, -6, -3 and 0. The
default value of this object is -6 dB. |
| xdslDevMVLSpecificIfConfig | 1.3.6.1.4.1.1795.2.24.9.2.3 | | | |
| xdslDevMVLSpecificIfConfigTable | 1.3.6.1.4.1.1795.2.24.9.2.3.1 | | not-accessible | The xdslDevMVLSpecificIfConfigTable provides config information specific
to a xDSL(MVL) device, or system. The table is indexed by an
object which corresponds to ifIndex. These ifIndex entries,
themselves, denote and identify specific xdsl(Mvl) interfaces on
the board or module. |
| xdslDevMVLSpecificIfConfigEntry | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1 | | not-accessible | Describes a specific xDSL(MVL) interface entry. |
| INT xdslDevMVLSpecificIfConfigMaxPortSpeed | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.1 | INTEGER | read-write | The value of this object corresponds to the upper bound
port speed of the specified port. The speeds are measured
in kbps. |
| INT xdslDevMVLSpecificIfConfigOnHookTxPowerAttenuation | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.2 | INTEGER | read-write | This value corresponds to the On-hook Transmitt Power Attenuation
in dB for the access node and the service node. This value represents
both downstream and upstream power level in dB while the phone is
On-hook. Permissible values are -2, 1, 4, 7, and +10. The
default value of this object is 10 dB. |
| INT xdslDevMVLSpecificIfConfigOffHookTxPowerAttenuation | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.3 | INTEGER | read-write | This value corresponds to the Off-hook Transmitt Power Attenuation
in dB for the access node and the service node. This value represents
both downstream and upstream power level in dB while the phone is
Off-hook. Permissible values are -11, -8, -5, -2, 1, 4, -2, 1, 4
and +7. The default value of this object is 7 dB. |
| xdslDevSDSLSpecificIfConfig | 1.3.6.1.4.1.1795.2.24.9.2.4 | | | |
| xdslDevSDSLSpecificIfConfigTable | 1.3.6.1.4.1.1795.2.24.9.2.4.1 | | not-accessible | The xdslDevSDSLSpecificIfConfigTable provides configuration
specific to the SDSL link. |
| xdslDevSDSLSpecificIfConfigEntry | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1 | | not-accessible | Describes a specific SDSL configuration entry. |
| INT xdslDevSDSLSpecificIfConfigFixedPortSpeed | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.1 | INTEGER | read-write | The value of this object corresponds to both upstream
and downstream speed of the specified port. All the
speeds are in kbps. The value of this object is used
only when the port behaviour is fixed. |
| INT xdslDevSDSLSpecificIfConfigMaxPortSpeed | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.2 | INTEGER | read-write | The value of this object corresponds to the upper bound
port speed of the specified port when the port behaviour
is adaptive. The speeds are measured in kbps. |
| INT xdslDevSDSLSpecificIfConfigFixedPortSpeedNx128Mode | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.3 | INTEGER | read-write | The value of this object applies to both upstream
and downstream speed of the specified port when the
line rate mode is configured as Nx128 mode. All the
speeds are in kbps. The value of this object is used
only when the port behaviour is fixed and the line rate
is Nx128 mode, and doesn't take effect in the standard mode. |
| INT xdslDevSDSLSpecificIfConfigMaxPortSpeedNx128Mode | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.4 | INTEGER | read-write | The value of this object corresponds to the upper bound
port speed of the specified port when the port behaviour
is adaptive and the line rate is Nx128 mode, and doesn't
take effect in the standard mode. The speeds are measured
in kbps. |
| xdslDevIDSLSpecificIfConfig | 1.3.6.1.4.1.1795.2.24.9.2.5 | | | |
| xdslDevIDSLSpecificIfConfigTable | 1.3.6.1.4.1.1795.2.24.9.2.5.1 | | not-accessible | The xdslDevIDSLSpecificIfConfigTable provides configuration
specific to the IDSL link. |
| xdslDevIDSLSpecificIfConfigEntry | 1.3.6.1.4.1.1795.2.24.9.2.5.1.1 | | not-accessible | Describes a specific IDSL configuration entry. |
| INT xdslDevIDSLSpecificIfConfigPortSpeed | 1.3.6.1.4.1.1795.2.24.9.2.5.1.1.1 | INTEGER | read-write | The value of this object corresponds to both upstream
and downstream speed of the specified port. All the
speeds are in kbps. Allowed speeds are 64, 128 and 144
kbps. The default value for this object is 128 kbps. |
| INT xdslDevIDSLSpecificIfConfigTimingPortTransceiverMode | 1.3.6.1.4.1.1795.2.24.9.2.5.1.1.2 | INTEGER | read-write | The transceiver mode selected on the timing source port.
Only one IDSL port can be set to NT mode. This timing
will then be distributed to all other IDSL ports in the
chassis that are set to LT.
The selected xdslDevIDSLPrimaryTimingSourcePort provides clocking
signals to the DSLAM when the transceiver mode is set to Network
timing. The port selected for Network Timing mode will probably not
used for customer data, but will receive a 2.048 Mhz Network clocking
signal from a central office timing source and distribute this timing
to other IDSL port cards. |
| xdslIfConfigMIBTraps | 1.3.6.1.4.1.1795.2.24.9.4 | | | |
