PDN-XDSL-INTERFACE-MIB DEFINITIONS ::= BEGIN

-- Version :  0.2
-- Added xdslDevGenericIfConfigLineRateMode in xdslDevGenericIfConfigTable
-- Added xdslDevSDSLSpecificIfConfigFixedPortSpeedNx128Mode and
--       xdslDevSDSLSpecificIfConfigMaxPortSpeedNx128Mode
-- Updated by Z. Pan

-- Version :  0.1 DRAFT
-- Enterprise Time mib
-- Copyright (C) 1999 Paradyne Corporation.

-- Created by : Rajesh Gowda

IMPORTS
     
   TAddress, TruthValue,
   RowStatus,DisplayString
    FROM SNMPv2-TC
   IpAddress, Counter,TimeTicks
    FROM RFC1155-SMI
   OBJECT-TYPE
     FROM RFC-1212
   TRAP-TYPE
     FROM RFC-1215
   ifIndex
     FROM RFC1213-MIB
   pdn-xdsl
     FROM PDN-HEADER-MIB
     ;

 xdslIfConfigMIBObjects        OBJECT IDENTIFIER ::= { pdn-xdsl 2 }
 xdslIfConfigMIBTraps          OBJECT IDENTIFIER ::= { pdn-xdsl 4 }
 xdslDevGenericIfConfig        OBJECT IDENTIFIER ::= { xdslIfConfigMIBObjects 1 }
 xdslDevRADSLSpecificIfConfig  OBJECT IDENTIFIER ::= { xdslIfConfigMIBObjects 2 }
 xdslDevMVLSpecificIfConfig    OBJECT IDENTIFIER ::= { xdslIfConfigMIBObjects 3 }
 xdslDevSDSLSpecificIfConfig   OBJECT IDENTIFIER ::= { xdslIfConfigMIBObjects 4 }
 xdslDevIDSLSpecificIfConfig   OBJECT IDENTIFIER ::= { xdslIfConfigMIBObjects 5 }

 -- The xdslDevGenericIfConfig group. Implementation of this group is
 -- mandatory for all type of DSL.

 xdslDevGenericIfConfigTable OBJECT-TYPE
   SYNTAX SEQUENCE OF XdslDevGenericIfConfigEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
     "The xdslDevGenericIfConfigTable provides config information 
      generic to a xDSL device, or system. The table is indexed by an 
      object which corresponds to ifIndex. These ifIndex entries, 
      themselves, denote and identify specific xdsl interfaces on
      the board or module. Also the configuration parameters are
      grouped into two broad categories, 'up' and 'down'. 'up'
      reflects the upstream direction (from the customer premises
      to the central office). 'Down' reflects the downstream
      direction (from the central office to the customer premises)"
 ::= { xdslDevGenericIfConfig 1 }

 xdslDevGenericIfConfigEntry OBJECT-TYPE
   SYNTAX XdslDevGenericIfConfigEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
     "Describes a specific xDSL interface entry."
   INDEX { ifIndex }
 ::= { xdslDevGenericIfConfigTable 1 }

 XdslDevGenericIfConfigEntry ::=
   SEQUENCE {
     xdslDevGenericIfConfigPortSpeedBehaviour
       INTEGER,
     xdslDevGenericIfConfigMarginThreshold 
       INTEGER,
     xdslDevGenericIfConfigPortID
       DisplayString (SIZE (1..40)),
     xdslDevGenericIfConfigLinkUpDownTransitionThreshold
       INTEGER,
     xdslDevGenericIfConfigLineEncodeType
       INTEGER,
     xdslDevGenericIfConfigLineRateMode
       INTEGER
  }

 xdslDevGenericIfConfigPortSpeedBehaviour OBJECT-TYPE
   SYNTAX INTEGER {
     fixed (1),
     adaptive (2)
   }
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the
      behaviour of the specified port. The default
      value for this object is fixed (1). "
 ::= { xdslDevGenericIfConfigEntry 1 }

 xdslDevGenericIfConfigMarginThreshold OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
    "The value of this object corresponds to the offset from
     the startup margin. The threshold margin is calculated
     by subtracting the offset from the startup margin. 
     Permissible range of values are between -7 and 14.
     A value of -9999 disables the threshold check. The default
     value of this object is 3"
 ::= { xdslDevGenericIfConfigEntry 2 }

 xdslDevGenericIfConfigPortID OBJECT-TYPE
   SYNTAX DisplayString (SIZE (1..40))
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to  40 character
      information only field that identifies what the DSL
      port is connected to (Circuit ID, MDF location, 
      Customer name, etc.)"
 ::= { xdslDevGenericIfConfigEntry 3 }

 xdslDevGenericIfConfigLinkUpDownTransitionThreshold OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the threshold
      value for link up-down transitions. If link up-down's exceed
      this threshold value a xdslLinkupDownTransitions
      trap is generated. This value would represent the number
      of link up-down transitions in a 15 minute interval. A value
      of -9999 disables the threshold check. The default value for this
      object is 0"
 ::= { xdslDevGenericIfConfigEntry 4 }
 
 xdslDevGenericIfConfigLineEncodeType OBJECT-TYPE
   SYNTAX INTEGER {
       other  (1),
       cap    (2),
       twoB1q (3),
       mvl    (4),
       g-lite (5),
       dmt    (6)
    }
   ACCESS read-only
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the line
      encoding technology used for data transmission over
      the the dsl link."
 ::= { xdslDevGenericIfConfigEntry 5 }
     
 xdslDevGenericIfConfigLineRateMode OBJECT-TYPE
   SYNTAX INTEGER {
       standard (1),
       nx128    (2)
    }
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object is used to choose the line
      rate list for data transmission over the dsl link.
      The default value is standard(1). "
 ::= { xdslDevGenericIfConfigEntry 6 }
 
 -- The xdslDevRADSLSpecificIfConfig group. Implementation of this
 -- group is mandatory for RADSL.

 xdslDevRADSLSpecificIfConfigTable OBJECT-TYPE
   SYNTAX SEQUENCE OF XdslDevRADSLSpecificIfConfigEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
     "The xdslDevRADSLSpecificIfConfigTable provides config information
      specific to a xDSL device, or system. The table is indexed by
      an object which corresponds to ifIndex. These ifIndex entries, 
      themselves, denote and identify specific xdsl interfaces on
      the board or module. Also the configuration parameters are
      grouped into two broad categories, 'up' and 'down'. 'up'
      reflects the upstream direction (from the customer premises
      to the central office). 'Down' reflects the downstream
      direction (from the central office to the customer premises)"
 ::= { xdslDevRADSLSpecificIfConfig 1 }

 xdslDevRADSLSpecificIfConfigEntry OBJECT-TYPE
   SYNTAX XdslDevRADSLSpecificIfConfigEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
     "Describes a specific xDSL interface entry."
   INDEX { ifIndex }
 ::= { xdslDevRADSLSpecificIfConfigTable 1 }

 XdslDevRADSLSpecificIfConfigEntry ::=
   SEQUENCE {
     xdslDevRADSLSpecificIfConfigUpFixedPortSpeed 
       INTEGER,
     xdslDevRADSLSpecificIfConfigDownFixedPortSpeed 
       INTEGER,
     xdslDevRADSLSpecificIfConfigUpAdaptiveUpperBoundPortSpeed 
       INTEGER,
     xdslDevRADSLSpecificIfConfigUpAdaptiveLowerBoundPortSpeed 
       INTEGER,
     xdslDevRADSLSpecificIfConfigDownAdaptiveUpperBoundPortSpeed 
       INTEGER,
     xdslDevRADSLSpecificIfConfigDownAdaptiveLowerBoundPortSpeed 
       INTEGER,
     xdslDevRADSLSpecificIfConfigReedSolomonDownFwdErrCorrection 
       INTEGER,
     xdslDevRADSLSpecificIfConfigStartUpMargin
       INTEGER (-3..9),
     xdslDevRADSLSpecificIfConfigTxPowerAttenuation
       INTEGER,
     xdslDevRADSLSpecificIfConfigSnTxPowerAttenuation
       INTEGER
  }

 xdslDevRADSLSpecificIfConfigUpFixedPortSpeed OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the upstream
      speed of the specified port for fixed port speed
      behaviour. All the speeds are in kbps.
      If the port speed behaviour is adaptive an error
      of noSuchName will be returned by the agent."
 ::= { xdslDevRADSLSpecificIfConfigEntry 1 }

 xdslDevRADSLSpecificIfConfigDownFixedPortSpeed OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the downstream
      speed of the specified port for fixed port speed
      behaviour. All the speeds are in kbps. 
      If the port speed behaviour is adaptive an error of noSuchName
      will be returned by the agent.  "
 ::= { xdslDevRADSLSpecificIfConfigEntry 2 }

 xdslDevRADSLSpecificIfConfigUpAdaptiveUpperBoundPortSpeed OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the 
      upper bound for the upstream port speed of the specified port
      for adaptive port speed behaviour. The speeds are measured
      in kbps. If the port speed behaviour is fixed
      an error of noSuchName will be returned by the agent."
 ::= { xdslDevRADSLSpecificIfConfigEntry 3 }

 xdslDevRADSLSpecificIfConfigUpAdaptiveLowerBoundPortSpeed OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the
      lower bound for the upstream port speed of the 
      specified port for adaptive port speed behaviour
      in kbps. If the port speed behaviour is fixed an 
	  error of noSuchName will be returned by the agent.  
	  The value -9999 should be used to disable the lower
      bound threshold check. The default value for this 
	  object is -9999 "
 ::= { xdslDevRADSLSpecificIfConfigEntry 4 }

 xdslDevRADSLSpecificIfConfigDownAdaptiveUpperBoundPortSpeed OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to 
      the upper bound allowed for the downstream port speed 
      of the specified port for adaptive port speed 
      behaviour. The speeds are measured in kbps. 
      If the port speed behaviour is fixed an error of noSuchName
      will be returned by the agent."
 ::= { xdslDevRADSLSpecificIfConfigEntry 5 }

 xdslDevRADSLSpecificIfConfigDownAdaptiveLowerBoundPortSpeed OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the
      Minimum lower bound allowed for the downstream port speed 
      of the specified port for adaptive port speed behaviour.
      If the port speed behaviour is fixed an error of noSuchName
      will be returned by the agent.  The speeds are measured in kbps.
      The value -9999 is used to disable the lower bound threshold 
      check.The default value for this object is -9999"
 ::= { xdslDevRADSLSpecificIfConfigEntry 6 }

 xdslDevRADSLSpecificIfConfigReedSolomonDownFwdErrCorrection OBJECT-TYPE
   SYNTAX INTEGER {
     minimizeError (1),
     minimizeDelay (2),
     reedSolomonNotSupported(3)
   }
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the
      Reed-Solomon forward error correction in the downstream
      direction. The default value of this object should be 
      minimizeError (1)."
 ::= { xdslDevRADSLSpecificIfConfigEntry 7 }

 xdslDevRADSLSpecificIfConfigStartUpMargin OBJECT-TYPE
   SYNTAX INTEGER (-3..9)
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     " The value of this object corresponds to the startup value
       of the margin for a DSL interface (specified by ifIndex).
       The unit is db (decibels. The higher the margin the better
       the quality of the line. The default value of this object is 3."
 ::= { xdslDevRADSLSpecificIfConfigEntry 8 }

 xdslDevRADSLSpecificIfConfigTxPowerAttenuation OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     " This value corresponds to the Transmitt Power Attenuation in
       dB for the access node. This value represents the downstream
       power level in dB. Permissible values are -6, -3 and 0.
       The default value of this object is 0 dB. The power levels +3
       and +6 may be used in future."
 ::= { xdslDevRADSLSpecificIfConfigEntry 9 }

 xdslDevRADSLSpecificIfConfigSnTxPowerAttenuation OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     " This value corresponds to the Transmitt Power Attenuation in dB
       for the service node. This value represents the upstream power
       level in dB. Permissible values are -9, -6, -3 and 0. The 
       default value of this object is -6 dB."

 ::= { xdslDevRADSLSpecificIfConfigEntry 10 }

 -- The xdslDevMVLSpecificConfig group. Implementation of this group is
 -- mandatory for MVL 

 xdslDevMVLSpecificIfConfigTable OBJECT-TYPE
   SYNTAX SEQUENCE OF XdslDevMVLSpecificIfConfigEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
     "The xdslDevMVLSpecificIfConfigTable provides config information specific 
      to a xDSL(MVL) device, or system. The table is indexed by an 
      object which corresponds to ifIndex. These ifIndex entries, 
      themselves, denote and identify specific xdsl(Mvl) interfaces on
      the board or module. "
 ::= { xdslDevMVLSpecificIfConfig 1 }

 xdslDevMVLSpecificIfConfigEntry OBJECT-TYPE
   SYNTAX XdslDevMVLSpecificIfConfigEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
     "Describes a specific xDSL(MVL) interface entry."
   INDEX { ifIndex }
 ::= { xdslDevMVLSpecificIfConfigTable 1 }

 XdslDevMVLSpecificIfConfigEntry ::=
   SEQUENCE {
     xdslDevMVLSpecificIfConfigMaxPortSpeed 
       INTEGER,
     xdslDevMVLSpecificIfConfigOnHookTxPowerAttenuation
       INTEGER,
     xdslDevMVLSpecificIfConfigOffHookTxPowerAttenuation
       INTEGER
  }

 xdslDevMVLSpecificIfConfigMaxPortSpeed OBJECT-TYPE
   SYNTAX INTEGER 
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the upper bound
      port speed of the specified port. The speeds are measured 
      in kbps."
 ::= { xdslDevMVLSpecificIfConfigEntry 1 }

 xdslDevMVLSpecificIfConfigOnHookTxPowerAttenuation OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     " This value corresponds to the On-hook Transmitt Power Attenuation 
       in dB for the access node and the service node. This value represents
       both downstream and upstream power level in dB while the phone is
       On-hook. Permissible values are -2, 1, 4, 7, and +10. The
       default value of this object is 10 dB."
 ::= { xdslDevMVLSpecificIfConfigEntry 2 }

 xdslDevMVLSpecificIfConfigOffHookTxPowerAttenuation OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     " This value corresponds to the Off-hook Transmitt Power Attenuation 
       in dB for the access node and the service node. This value represents
       both downstream and upstream power level in dB while the phone is
       Off-hook. Permissible values are -11, -8, -5, -2, 1, 4, -2, 1, 4 
       and +7. The default value of this object is 7 dB. "
 ::= { xdslDevMVLSpecificIfConfigEntry 3 }

 -- The xdslDevSDSLSpecificIfConfig group. Implementation of this group is
 -- mandatory for SDSL 

 xdslDevSDSLSpecificIfConfigTable OBJECT-TYPE
   SYNTAX SEQUENCE OF XdslDevSDSLSpecificIfConfigEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
     "The xdslDevSDSLSpecificIfConfigTable provides configuration 
      specific to the SDSL link."
 ::= { xdslDevSDSLSpecificIfConfig 1 }

 xdslDevSDSLSpecificIfConfigEntry OBJECT-TYPE
   SYNTAX XdslDevSDSLSpecificIfConfigEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
     "Describes a specific SDSL configuration entry."
   INDEX { ifIndex }
 ::= { xdslDevSDSLSpecificIfConfigTable 1 }

 XdslDevSDSLSpecificIfConfigEntry ::=
   SEQUENCE {
     xdslDevSDSLSpecificIfConfigFixedPortSpeed
       INTEGER,
    xdslDevSDSLSpecificIfConfigMaxPortSpeed
       INTEGER,
    xdslDevSDSLSpecificIfConfigFixedPortSpeedNx128Mode
       INTEGER,
    xdslDevSDSLSpecificIfConfigMaxPortSpeedNx128Mode
       INTEGER
 }

 xdslDevSDSLSpecificIfConfigFixedPortSpeed OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to both upstream
      and downstream speed of the specified port. All the
      speeds are in kbps. The value of this  object is used
      only when the port behaviour is fixed."
 ::= { xdslDevSDSLSpecificIfConfigEntry 1 }

 xdslDevSDSLSpecificIfConfigMaxPortSpeed OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the upper bound
      port speed of the specified port when the port behaviour
      is adaptive. The speeds are measured in kbps."
 ::= { xdslDevSDSLSpecificIfConfigEntry 2 }

 xdslDevSDSLSpecificIfConfigFixedPortSpeedNx128Mode OBJECT-TYPE
   SYNTAX INTEGER (0..2147483647)
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object applies to both upstream
      and downstream speed of the specified port when the 
      line rate mode is configured as Nx128 mode. All the 
      speeds are in kbps. The value of this object is used
      only when the port behaviour is fixed and the line rate
      is Nx128 mode, and doesn't take effect in the standard mode."
 ::= { xdslDevSDSLSpecificIfConfigEntry 3 }

 xdslDevSDSLSpecificIfConfigMaxPortSpeedNx128Mode OBJECT-TYPE
   SYNTAX INTEGER (0..2147483647)
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to the upper bound
      port speed of the specified port when the port behaviour
      is adaptive and the line rate is Nx128 mode, and doesn't
      take effect in the standard mode. The speeds are measured
      in kbps."
 ::= { xdslDevSDSLSpecificIfConfigEntry 4 }

 -- The xdslDevIDSLSpecificIfConfig group. Implementation of this group is
 -- mandatory for IDSL 

 xdslDevIDSLSpecificIfConfigTable OBJECT-TYPE
   SYNTAX SEQUENCE OF XdslDevIDSLSpecificIfConfigEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
     "The xdslDevIDSLSpecificIfConfigTable provides configuration 
      specific to the IDSL link."
 ::= { xdslDevIDSLSpecificIfConfig 1 }

 xdslDevIDSLSpecificIfConfigEntry OBJECT-TYPE
   SYNTAX XdslDevIDSLSpecificIfConfigEntry
   ACCESS not-accessible
   STATUS mandatory
   DESCRIPTION
     "Describes a specific IDSL configuration entry."
   INDEX { ifIndex }
 ::= { xdslDevIDSLSpecificIfConfigTable 1 }

 XdslDevIDSLSpecificIfConfigEntry ::=
   SEQUENCE {
     xdslDevIDSLSpecificIfConfigPortSpeed
       INTEGER,
     xdslDevIDSLSpecificIfConfigTimingPortTransceiverMode
       INTEGER
 }

 xdslDevIDSLSpecificIfConfigPortSpeed OBJECT-TYPE
   SYNTAX INTEGER
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The value of this object corresponds to both upstream
      and downstream speed of the specified port. All the
      speeds are in kbps. Allowed speeds are 64, 128 and 144
      kbps. The default value for this object is 128 kbps."
 ::= { xdslDevIDSLSpecificIfConfigEntry 1 }

 xdslDevIDSLSpecificIfConfigTimingPortTransceiverMode OBJECT-TYPE
   SYNTAX INTEGER {
          networkTiming (1),
          localTiming (2)
   }
   ACCESS read-write
   STATUS mandatory
   DESCRIPTION
     "The transceiver mode selected on the timing source port.
      Only one IDSL port can be set to NT mode. This timing
      will then be distributed to all other IDSL ports in the
      chassis that are set to LT.

      The selected xdslDevIDSLPrimaryTimingSourcePort provides clocking
      signals to the DSLAM when the transceiver mode is set to Network
      timing. The port selected for Network Timing mode will probably not
      used for customer data, but will receive a 2.048 Mhz Network clocking
      signal from a central office timing source and distribute this timing
      to other IDSL port cards."
 ::= { xdslDevIDSLSpecificIfConfigEntry 2 }

END