PDN-HEALTHANDSTATUS-MIB

All MIBs › PDN-HEALTHANDSTATUS-MIB

Category: Environmental Monitoring

Description: Reports chassis health and operational status including fan, power supply, and temperature sensor readings on Paradyne devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PDN-HEALTHANDSTATUS-MIB?

PDN-HEALTHANDSTATUS-MIB is a Paradyne enterprise MIB dedicated to overall chassis health and operational status reporting on Paradyne xDSL access devices. It exposes device-wide self-test results and history, an abort/failure status, a table tracking the outcome of individual SNMP SET requests, security-relevant data such as the source IP of the last authentication failure, and the text of the last trap the device generated. This is explicitly a hardware/software status-monitoring MIB -- used to confirm the device passed its self-tests, check whether it has entered a failure or abort state, verify whether recent SNMP configuration changes actually succeeded, and review the most recent alarm condition and any unauthorized access attempts. It does not declare a dependency on a standard IETF MIB, functioning as the central status/health module referenced by trap-enable settings in sibling MIBs like PDN-CONFIG-MIB. It is deployed on Paradyne xDSL access devices/DSLAMs where operators need a single place to check overall device health, self-test outcomes, and recent fault/security events via SNMP. Engineers can download the PDN-HEALTHANDSTATUS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in PDN-HEALTHANDSTATUS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Paradyne xDSL access equipment/DSLAM

Monitoring Examples

An operator polls devStatus and devHealthAndStatus to get the device's overall health summary, then checks devSelfTestResultTable/devSelfTestResults to confirm the most recent diagnostic pass succeeded. If devFailureStatus or devAbortStatus indicates a problem, devLastTrapString gives the text of the most recent alarm condition without needing separate trap logs. devSNMPSetStatusTable, keyed by devSNMPSetReqId, lets an operator confirm a previous SNMP SET actually completed rather than silently failing, and devAuthenticationFailureIpAddress flags the source of a recent unauthorized SNMP access attempt.

What Can Be Monitored

overall device health/status
self-test results
failure/abort status
SNMP SET request outcome
last trap/alarm text
authentication failure source IP

Imported Objects

From ENTITY-MIB

entPhysicalIndex

OBJECT-TYPE

From PDN-HEADER-MIB

pdn-devStatus

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

IpAddress

From RFC1213-MIB

DisplayString
ifIndex

OIDs

OID symbolic	OID numeric	Type	Access	Description
devStatus	1.3.6.1.4.1.1795.2.24.2.4.1
NTF devSelfTestFailure	1.3.6.1.4.1.1795.2.24.2.4.1.0.1			This trap signifies that the sending protocol's device has failed self test. The variable binding for this trap would be the selfTest devSelfTestResults object of the Health and Status MIB. The exact format of this display string will be well-documented in the Operational Specifications of the device.
NTF deviceFailure	1.3.6.1.4.1.1795.2.24.2.4.1.0.2			This trap signifies that the sending protocol's device has failed and the failure was not a result of a device test.
STR devHealthAndStatus	1.3.6.1.4.1.1795.2.24.2.4.1.1	DisplayString	read-only	Health and Status of the device. Health & Status is represented as a concatenation of health and status message strings, where each message string is separated by a semi-colon. Refer to device-specific user documentation for a complete description of the Health and Status codes.
STR devSelfTestResults	1.3.6.1.4.1.1795.2.24.2.4.1.2	DisplayString	read-only	Self-test results. Self-test (or power-up test) results summarizes the test results of each CCA, where each CCA test result is separated by a semi-colon. Refer to device-specific user documentation for a complete description of the self test codes and messages.
STR devAbortStatus	1.3.6.1.4.1.1795.2.24.2.4.1.3	DisplayString	read-only	Abort Status. The devAbortStatus object is used to retrieve the latest abort status that is stored in the agent. The agent will need to save the latest abort information in non-volatile memory so that it will be available immediately after a fatal reset. How long the latest failure information is remembered after this point is an implementation issue. Refer to device-specific user documentation for a complete description of the abort codes and/or messages.
devSNMPSetStatusTable	1.3.6.1.4.1.1795.2.24.2.4.1.4		not-accessible	A table containing SNMP Set command Statuses when an error occurs. It contains maximum of 5 entries. Oldest entry is pushed out when the table is full and a new entry is added.
devSNMPSetStatusEntry	1.3.6.1.4.1.1795.2.24.2.4.1.4.1		not-accessible	The information regarding each SNMP Set command Status when en error occurs. Each entry is index by a request ID generated by the client and attached to the UDP when the Set command is sent.
INT devSNMPSetReqId	1.3.6.1.4.1.1795.2.24.2.4.1.4.1.1	INTEGER	read-only	The Request ID which identifies the SNMP Set command in error.
STR devSNMPSetStatus	1.3.6.1.4.1.1795.2.24.2.4.1.4.1.2	DisplayString	read-only	Indicates the error message string associated with the Set command of this row in the table.
IP devAuthenticationFailureIpAddress	1.3.6.1.4.1.1795.2.24.2.4.1.5	IpAddress	read-only	Authentication Failure Ip Address is used when a authenticationFailure trap is generated. The single varbind represents the ip address causing the error. If the ip address is not known, 0.0.0.0 is used.
STR devLastTrapString	1.3.6.1.4.1.1795.2.24.2.4.1.6	DisplayString	read-only	This object contains a textual description of the last trap that was processed by the device. The exact text in the description is device specific and should be contained user documentation outside of this MIB. It is recommended that the important information is contained within the first 100 characters.
STR devFailureStatus	1.3.6.1.4.1.1795.2.24.2.4.1.7	DisplayString	read-only	Device Failure status. Conditions that cause failure are further described in the device documentation.
INT devStatusTrapEnable	1.3.6.1.4.1.1795.2.24.2.4.1.8	INTEGER	read-write	This object provides ability to enable or disable individual enterprise traps. The object is bit map represented as a sum. The bit positions are: 1 deviceSelfTestFailure 2 deviceFailure
devSelfTestResultTable	1.3.6.1.4.1.1795.2.24.2.4.1.9		not-accessible	A table containing results of power on selftest for the whole unit.
devSelfTestResultEntry	1.3.6.1.4.1.1795.2.24.2.4.1.9.1		not-accessible	The information regarding each SelfTest on each unit.
STR devSelfTestResult	1.3.6.1.4.1.1795.2.24.2.4.1.9.1.1	DisplayString	read-only	Self-test results. Self-test (or power-up test) results summarizes the test results of each interface, where each CCA test result is separated by a semi-colon. Refer to device-specific user documentation for a complete description of the self test codes and messages.

RFC description

PDN device health and status MIB for monitoring device health, self-test results, and failure conditions.

Start monitoring Paradyne xDSL access equipment/DSLAM (chassis health/self-test/security status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PDN-HEALTHANDSTATUS-MIB

What Is PDN-HEALTHANDSTATUS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description