PANDATEL-ETC-MODEM-MIB

All MIBs › PANDATEL-ETC-MODEM-MIB

Category: Modems

Description: Manages Pandatel ETC series modem configuration, line status, and performance statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PANDATEL-ETC-MODEM-MIB?

PANDATEL-ETC-MODEM-MIB is a vendor-specific MIB for Pandatel's ETC series line modems, rack-mounted physical-layer equipment used to extend telecom circuits over copper pairs. It exposes rack/slot inventory and identification, along with data equipment emulation mode, alarm status, remote access mode, forced remote access, and operation mode for each modem unit. Its monitoring emphasis is on hardware status - mdmAlarm directly surfaces hardware fault/alarm conditions on a given modem, while mdmRemoteAccessMode and mdmOperationMode indicate whether the unit is reachable and in which mode it's running, both important for confirming a line card is healthy and correctly provisioned. As a self-contained vendor line-modem MIB it has no evident dependency on IETF standard MIBs beyond the base SNMP framework. It's typically deployed in telecom central office or premises racks housing multiple ETC modem cards, managed centrally via an element management system. Engineers can download the PANDATEL-ETC-MODEM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in PANDATEL-ETC-MODEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Pandatel ETC series line modem

Monitoring Examples

An operator would enumerate etcModemTable/etcTableEntry rows by mdmRack, mdmModem, and mdmPosition to inventory installed cards, then poll mdmAlarm to spot a card reporting a hardware fault. mdmRemoteAccessMode and mdmForcedRemoteAccess would be checked when a technician needs to confirm whether remote diagnostic access to a distant modem is currently permitted or has been forced on, and mdmDataEquipmentEmulation/mdmOperationMode would be reviewed to verify the unit is emulating the correct mode for its attached equipment.

What Can Be Monitored

modem rack/slot position
alarm/fault status
remote access mode
operation mode
data equipment emulation mode

Imported Objects

From PANDATEL-MODEM-MIB

device-id
mdmSpecifics	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
etc	1.3.6.1.4.1.760.1.1.2.1.10.901
etcModemTable	1.3.6.1.4.1.760.1.1.2.1.10.901.1		not-accessible	The table of all ETC modems in this housing.
etcTableEntry	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1		not-accessible	The index of the table.
INT mdmRack	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.1	INTEGER	read-only	The index of the rack where the modem is installed.
INT mdmModem	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.2	INTEGER	read-only	This variable displays the slot number where the corresponding modem is installed in the rack.
INT mdmPosition	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.3	INTEGER	read-only	This variable displays the location of the corresponding modem: 'local' or 'remote'. The modem which is plugged into a managed rack is 'local', the counterpart is 'remote'.
STR mdmModemName	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.5	DisplayString	read-only	A verbal name of this modem.
INT mdmDataEquipmentEmulation	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.6	INTEGER	read-only	Interface mode of the unit: 'dte' or 'dce', 'te' or 'nt'.
INT mdmModemProperty	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.7	INTEGER	read-write	The speed class of the unit: 'eth100base-tx-full-duplex' or 'eth100base-tx-half-duplex'.
INT mdmAlarm	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.15	INTEGER	read-only	The status of local alarm: 'off' or 'on'.
INT mdmRemoteAccessMode	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.64	INTEGER	read-write	The possibility of remote management: 'enabled', 'disabled local' or 'disable local and remote'. Once disabled management at local and remote unit, it is not possible to enable it at the remote unit again.
INT mdmForcedRemoteAccess	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.65	INTEGER	read-write	Activation of remote management: 'on' or 'off'. Status 'on' enables management of remote unit. During this process the link is restricted to management data. The transmission of user data is interrupted. Status 'off' disables management of remote unit. The link transmits user data.
INT mdmOperationMode	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.66	INTEGER	read-write	The possibility of operation mode: 'normal', 'remote-fault-detection mode' or 'link-pass-through'.
INT mdmFoPower	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.71	INTEGER	read-only	The status of transmitter power: 'low' or 'high'.
INT mdmAutoDetectModemProperty	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.74	INTEGER	read-write	The status of auto detect of modem property: 'off' or 'on'.
INT mdmInterfaceAlarmCondition	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.98	INTEGER	read-write	The alarm trigger mode at interface port: 'disable', i.e. no alarm is triggered, 'no-link-signal', i.e. an alarm is triggered if the link is down.
INT mdmLineAlarmCondition	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.99	INTEGER	read-write	The alarm trigger mode at line port: 'disable', i.e. no alarm is triggered, 'no-link-signal', i.e. an alarm is triggered if the link is down, 'laser-fail', i.e. an alarm is triggered if the laser diode is defective, or 'no-link-signal-or-laser-fail', i.e. the link is down or the laser diode is defective.
INT mdmStatusInterfacePort	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.140	INTEGER	read-write	The status 'disable': port is not active. The status 'enable': port is active.
INT mdmStatusLinePort	1.3.6.1.4.1.760.1.1.2.1.10.901.1.1.141	INTEGER	read-write	The status 'disable': port is not active. The status 'enable': port is active.
etc_modem	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.901

RFC description

Manages PANDATEL ETC modems in modem rack housing including modem-specific parameters and status.

Start monitoring Pandatel ETC series line modem with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PANDATEL-ETC-MODEM-MIB

What Is PANDATEL-ETC-MODEM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description