PANDATEL-ETC-MODEM-MIB DEFINITIONS ::= BEGIN -- This is the private mib group section for the ETC modems. -- Because these modems must be installed in the PANDATEL modem rack -- the PANDATEL-MODEM-MIB also applies. -- Ver.1.00 Nov.21.2000 IMPORTS enterprises FROM RFC1155-SMI DisplayString FROM RFC1213-MIB OBJECT-TYPE FROM RFC-1212 mdmSpecifics, device-id FROM PANDATEL-MODEM-MIB; -- ********************** THE MDM-ETC SUBTREE ****************************** -- the specific identifier is identical to the modem type integer -- of the ETC modem entries in the PANDATEL-MODEM-MIB mdmModemTable. etc-modem OBJECT IDENTIFIER ::= { device-id 901 } -- chassis-mib etc OBJECT IDENTIFIER ::= { mdmSpecifics 901 } -- this subtree etcModemTable OBJECT-TYPE SYNTAX SEQUENCE OF EtcTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The table of all ETC modems in this housing." ::= { etc 1 } etcTableEntry OBJECT-TYPE SYNTAX EtcTableEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The index of the table." INDEX { mdmRack, mdmModem, mdmPosition } ::= { etcModemTable 1 } EtcTableEntry ::= SEQUENCE { mdmRack INTEGER, mdmModem INTEGER, mdmPosition INTEGER, mdmModemName DisplayString, mdmDataEquipmentEmulation INTEGER, mdmModemProperty INTEGER, mdmAlarm INTEGER, mdmRemoteAccessMode INTEGER, mdmForcedRemoteAccess INTEGER, mdmOperationMode INTEGER, mdmFoPower INTEGER, mdmAutoDetectModemProperty INTEGER, mdmInterfaceAlarmCondition INTEGER, mdmLineAlarmCondition INTEGER, mdmStatusInterfacePort INTEGER, mdmStatusLinePort INTEGER } mdmRack OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index of the rack where the modem is installed." ::= { etcTableEntry 1 } mdmModem OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the slot number where the corresponding modem is installed in the rack." ::= { etcTableEntry 2 } mdmPosition OBJECT-TYPE SYNTAX INTEGER { local (1), remote (2) } ACCESS read-only STATUS mandatory DESCRIPTION "This variable displays the location of the corresponding modem: 'local' or 'remote'. The modem which is plugged into a managed rack is 'local', the counterpart is 'remote'." ::= { etcTableEntry 3 } mdmModemName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "A verbal name of this modem." ::= { etcTableEntry 5 } mdmDataEquipmentEmulation OBJECT-TYPE SYNTAX INTEGER { other (1), to-hub (8), to-nic (9), unknown (99) } ACCESS read-only STATUS mandatory DESCRIPTION "Interface mode of the unit: 'dte' or 'dce', 'te' or 'nt'." ::= { etcTableEntry 6 } mdmModemProperty OBJECT-TYPE SYNTAX INTEGER { other (1), eth100base-tx-full-duplex (16), eth100base-tx-half-duplex (17), unknown (99) } ACCESS read-write STATUS mandatory DESCRIPTION "The speed class of the unit: 'eth100base-tx-full-duplex' or 'eth100base-tx-half-duplex'." ::= { etcTableEntry 7 } mdmAlarm OBJECT-TYPE SYNTAX INTEGER { other (1), off (2), on (3) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of local alarm: 'off' or 'on'." ::= { etcTableEntry 15 } mdmRemoteAccessMode OBJECT-TYPE SYNTAX INTEGER { other (1), enable (5), disable-local (8), disable-local-and-remote (9) } ACCESS read-write STATUS mandatory DESCRIPTION "The possibility of remote management: 'enabled', 'disabled local' or 'disable local and remote'. Once disabled management at local and remote unit, it is not possible to enable it at the remote unit again." ::= { etcTableEntry 64 } mdmForcedRemoteAccess OBJECT-TYPE SYNTAX INTEGER { off (1), on (2) } ACCESS read-write STATUS mandatory DESCRIPTION "Activation of remote management: 'on' or 'off'. Status 'on' enables management of remote unit. During this process the link is restricted to management data. The transmission of user data is interrupted. Status 'off' disables management of remote unit. The link transmits user data." ::= { etcTableEntry 65 } mdmOperationMode OBJECT-TYPE SYNTAX INTEGER { other (1), normal (7), remote-fault-detection (8), link-pass-through (9) } ACCESS read-write STATUS mandatory DESCRIPTION "The possibility of operation mode: 'normal', 'remote-fault-detection mode' or 'link-pass-through'." ::= { etcTableEntry 66 } mdmFoPower OBJECT-TYPE SYNTAX INTEGER { other (1), low (2), high (3) } ACCESS read-only STATUS mandatory DESCRIPTION "The status of transmitter power: 'low' or 'high'." ::= { etcTableEntry 71 } mdmAutoDetectModemProperty OBJECT-TYPE SYNTAX INTEGER { other (1), off (2), on (3) } ACCESS read-write STATUS mandatory DESCRIPTION "The status of auto detect of modem property: 'off' or 'on'." ::= { etcTableEntry 74 } mdmInterfaceAlarmCondition OBJECT-TYPE SYNTAX INTEGER { other (1), disable (2), no-link-signal (3), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "The alarm trigger mode at interface port: 'disable', i.e. no alarm is triggered, 'no-link-signal', i.e. an alarm is triggered if the link is down." ::= { etcTableEntry 98 } mdmLineAlarmCondition OBJECT-TYPE SYNTAX INTEGER { other (1), disable (2), no-link-signal (3), laser-fail (4), no-link-signal-or-laser-fail (5), not-available (100) } ACCESS read-write STATUS mandatory DESCRIPTION "The alarm trigger mode at line port: 'disable', i.e. no alarm is triggered, 'no-link-signal', i.e. an alarm is triggered if the link is down, 'laser-fail', i.e. an alarm is triggered if the laser diode is defective, or 'no-link-signal-or-laser-fail', i.e. the link is down or the laser diode is defective." ::= { etcTableEntry 99 } mdmStatusInterfacePort OBJECT-TYPE SYNTAX INTEGER { other (1), disable (2), enable (3) } ACCESS read-write STATUS mandatory DESCRIPTION "The status 'disable': port is not active. The status 'enable': port is active." ::= { etcTableEntry 140 } mdmStatusLinePort OBJECT-TYPE SYNTAX INTEGER { other (1), disable (2), enable (3) } ACCESS read-write STATUS mandatory DESCRIPTION "The status 'disable': port is not active. The status 'enable': port is active." ::= { etcTableEntry 141 } END