PANDATEL-MODEM-MIB

All MIBs › PANDATEL-MODEM-MIB

Category: Modems

Description:

Provides base SNMP management objects for Pandatel AG modem device configuration and line status monitoring.

Imported Objects

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
TimeTicks
enterprises

From RFC1213-MIB

DisplayString

What Is PANDATEL-MODEM-MIB?

This is the base Pandatel AG vendor MIB providing foundational SNMP management objects for their modem product line, covering rack-level inventory and basic device status. It exposes data such as the number of installed racks and modems, current device date/time, and a rack table describing each rack's type, description, and modem slot capacity/occupancy. It is used to monitor hardware status at the rack/chassis level, confirming how many modem slots are populated versus available, verifying device clock/date synchronization, and detecting configuration issues via loop-mode trap notifications. PANDATEL-MODEM-MIB SNMP monitoring gives operators a quick chassis-wide view of rack and modem health before they need to drill into type-specific modem MIBs for per-modem detail. As the base MIB in the Pandatel modem family, it is depended upon by more specific modules like PANDATEL-GMDF-MODEM-MIB, which extend it with per-modem-type detail. It is typically deployed by telecom access providers managing racks of Pandatel modems for leased-line or DSL access services.

IPNetwork Monitor allows you to monitor SNMP objects defined in PANDATEL-MODEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

installed rack/modem counts
rack type and modem slot occupancy
device current date/time
loop-mode trap events

Supported Devices

Pandatel AG modem chassis/rack

Monitoring Examples

An administrator would poll mdmInstalledRacks and mdmInstalledModems to get a quick inventory summary, then check rackEntry fields such as rackModemSlots versus rackModems to see whether a rack has unused capacity or is fully populated. Comparing mdmCurrentDate/mdmCurrentTime against the expected NTP-synced time would reveal a device with a drifting internal clock. An mdmLoopModeTraps notification firing would alert the operator that a modem entered loopback test mode, which needs to be cleared to restore normal traffic, providing a chassis-level view before drilling into type-specific modem MIBs.

OIDs

OID symbolic	OID numeric	Type	Access	Description
b_ac_x_5v_6a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.7
b_dc_24v_5v_su	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.10
b_dc_48v_5v_hc	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.9
b_dc_48v_5v_lc	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.8
backupPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.6
INT bertBERTest	1.3.6.1.4.1.760.1.1.2.1.7.1.4	INTEGER	read-write	This entry enables the execution of a BER test. Write requests with values other than 'start' or 'stop' will be rejected.
STR bertBitErrorRate	1.3.6.1.4.1.760.1.1.2.1.7.1.14	DisplayString	read-only	This entry indicates the bit error rate. It is provided as a string in the format 'd.ddE+/-dd'. Float scanf routines are capable of interpreting the string in the correct manner.
bertEntry	1.3.6.1.4.1.760.1.1.2.1.7.1		not-accessible	The index of thetable.
CTR bertErrorFreeTime	1.3.6.1.4.1.760.1.1.2.1.7.1.8	Counter	read-only	This entry shows the duration of error-free test transmission in seconds.
CTR bertErrors	1.3.6.1.4.1.760.1.1.2.1.7.1.11	Counter	read-only	This entry indicates the number of errors detected during the test.
CTR bertInErrorTime	1.3.6.1.4.1.760.1.1.2.1.7.1.7	Counter	read-only	This entry shows the duration of erroneous test transmission in seconds.
CTR bertKbitsReceived	1.3.6.1.4.1.760.1.1.2.1.7.1.10	Counter	read-only	This entry indicates the number of Kbits received during the test. When the counter wraps the bertKbitRecWrapped increases by one.
CTR bertKbitsRecWrapped	1.3.6.1.4.1.760.1.1.2.1.7.1.9	Counter	read-only	This is the number the bertKbitsReceived counter has wrapped.
INT bertModem	1.3.6.1.4.1.760.1.1.2.1.7.1.2	INTEGER	read-only	The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
INT bertPort	1.3.6.1.4.1.760.1.1.2.1.7.1.3	INTEGER	read-write	The index of the port where the BER test will be performed. The modem can only perform one test at a time. The test can only be performed on a subset of ports, usually the line ports. Write requests with different port numbers will be rejected. Write requests with valid line port numbers will be rejected while the BER test is running.
INT bertRack	1.3.6.1.4.1.760.1.1.2.1.7.1.1	INTEGER	read-only	The index of the rack where the modem is installed.
CTR bertRunTime	1.3.6.1.4.1.760.1.1.2.1.7.1.6	Counter	read-only	This entry indicates the duration of the BER test in seconds.
INT bertStatus	1.3.6.1.4.1.760.1.1.2.1.7.1.5	INTEGER	read-only	This entry indicates the status of the BER test.
CTR bertSyncLosts	1.3.6.1.4.1.760.1.1.2.1.7.1.12	Counter	read-only	This entry indicates the number of pattern sync losts detected during the test.
INT bertSyncStatus	1.3.6.1.4.1.760.1.1.2.1.7.1.13	INTEGER	read-only	This entry indicates the current pattern sync status.
cms_intelligent_slave	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10003
cms_slave	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10002
cms_snmp_master	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10001
comp_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.1
controlSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.6
device_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.2
device_stack_15s	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.6
fAN1_FAN2_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.1
fAN1_off_FAN2_off	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.2
fAN1_off_FAN2_on	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.4
fAN1_on_FAN2_off	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.3
fAN1_on_FAN2_on	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.5
fanonoff_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.7
hs_rack_10s_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.9
hs_rack_3s_1c_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.11
interfacePort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.2
linePort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.3
mdm_mgmt	1.3.6.1.4.1.760.1.1.2.1
mdm_oid	1.3.6.1.4.1.760.1.1.2.1.10.10000
mdmBERTTable	1.3.6.1.4.1.760.1.1.2.1.7		not-accessible	Table which contains information about all performable bit error rate tests.
STR mdmCurrentDate	1.3.6.1.4.1.760.1.1.2.1.1.13	DisplayString	read-write	This indicate the current date as 'mm/dd/yy'. The date will be used for local management.
STR mdmCurrentTime	1.3.6.1.4.1.760.1.1.2.1.1.14	DisplayString	read-write	This indicate the current time as 'hh:mm:ss'. The time will be used for local management.
STR mdmDescription	1.3.6.1.4.1.760.1.1.2.1.3.1.3	DisplayString	read-only	A verbal description of the modem.
mdmGroup	1.3.6.1.4.1.760.1.1.2.1.1
INT mdmIfDataRate	1.3.6.1.4.1.760.1.1.2.1.20.3	INTEGER	read-only	This variable shows the agent's data rate in bps.
INT mdmIfDialEnable	1.3.6.1.4.1.760.1.1.2.1.20.4	INTEGER	read-write	This variable enables the initialization of a dial modem in case of alarm. The following variables (5 to 10) are active only if this variable is enabled.
STR mdmIfDialString	1.3.6.1.4.1.760.1.1.2.1.20.6	DisplayString	read-write	This variable defines a modem command which is generated in case of alarm to dial-up a remote NMS station. If the dial string is not defined neither the init string nor the dial string is generated.
INT mdmIfDialTimeout	1.3.6.1.4.1.760.1.1.2.1.20.8	INTEGER	read-write	This variable defines a dial timeout for the modem in seconds.
INT mdmIfIdlePeriodBeforeDisconnect	1.3.6.1.4.1.760.1.1.2.1.20.10	INTEGER	read-write	This variable defines the period of time before disconnecting in seconds. If the value is '0' the modem will remain connected.
STR mdmIfInitString	1.3.6.1.4.1.760.1.1.2.1.20.5	DisplayString	read-write	This variable defines an init string which is generated in case of alarm to configure an external Hayes compatible modem.
INT mdmIfProtocol	1.3.6.1.4.1.760.1.1.2.1.20.2	INTEGER	read-only	This variable shows the agent's protocol type.
INT mdmIfRedialPause	1.3.6.1.4.1.760.1.1.2.1.20.9	INTEGER	read-write	This variable defines the duration of a redial pause in seconds.
INT mdmIfSendTTL	1.3.6.1.4.1.760.1.1.2.1.20.7	INTEGER	read-write	This variable defines the TTL (time to live) in seconds. After that time the generated traps will be deleted from the buffer. If the value is '0' the traps will remain in the buffer.
INT mdmIfType	1.3.6.1.4.1.760.1.1.2.1.20.1	INTEGER	read-only	This variable shows the agent's interface type.
INT mdmInstalledModems	1.3.6.1.4.1.760.1.1.2.1.1.2	INTEGER	read-only	This is the number of currently installed modems
INT mdmInstalledRacks	1.3.6.1.4.1.760.1.1.2.1.1.1	INTEGER	read-only	This is the number of currently installed modem racks.
INT mdmInterfacePorts	1.3.6.1.4.1.760.1.1.2.1.3.1.8	INTEGER	read-only	This entry indicates the number of interface ports of the modem. An interface port connects an external device.
INT mdmLinePorts	1.3.6.1.4.1.760.1.1.2.1.3.1.9	INTEGER	read-only	This entry indicates the number of line ports of the modem. A line port connects a remote modem.
INT mdmLoopModeTraps	1.3.6.1.4.1.760.1.1.2.1.1.3	INTEGER	read-write	This enables or disables traps generated by a Loop Mode status change at any local modem port of one of the installed modems (values: disable, enable).
mdmMgmtIfGroup	1.3.6.1.4.1.760.1.1.2.1.20
INT mdmModem	1.3.6.1.4.1.760.1.1.2.1.3.1.2	INTEGER	read-only	The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
mdmModemTable	1.3.6.1.4.1.760.1.1.2.1.3		not-accessible	Table which contains general information about the installed modems.
mdmPortSignalTable	1.3.6.1.4.1.760.1.1.2.1.6		not-accessible	Table which contains information about all port status signals.
mdmPortTable	1.3.6.1.4.1.760.1.1.2.1.5		not-accessible	Table which contains information about all ports.
INT mdmRack	1.3.6.1.4.1.760.1.1.2.1.3.1.1	INTEGER	read-only	The index of the rack where the modem is installed.
mdmRackTable	1.3.6.1.4.1.760.1.1.2.1.2		not-accessible	Table which contains information about the installed racks.
mdmRemoteAccess	1.3.6.1.4.1.760.1.1.2.1.9
INT mdmRemoteAccessStatus	1.3.6.1.4.1.760.1.1.2.1.3.1.7	INTEGER	read-only	This entry shows the access status to the remote counterpart of the modem. The standard value depends on the device. Some remote modems are always accessible, others are not accessible or can be switched to both modes (see 'mdmForcedRemoteAccess' in the specific modem MIB).
INT mdmSelfTest	1.3.6.1.4.1.760.1.1.2.1.3.1.5	INTEGER	read-write	This entry enables the execution of a selftest. Write requests with values other than 'start' or 'cancel' will be rejected. The result will be found in mdmSelfTestResult.
INT mdmSelfTestResult	1.3.6.1.4.1.760.1.1.2.1.3.1.6	INTEGER	read-only	This entry shows the result status of the last modem-dependent self test. After start, the status may change to 'running' before the first error that occured is displayed. If no error was detected the status changes to 'ok'.
mdmSpecifics	1.3.6.1.4.1.760.1.1.2.1.10
STR mdmUserName	1.3.6.1.4.1.760.1.1.2.1.3.1.4	DisplayString	read-write	A verbal description of the modem which can be changed by the manager.
mdmVerInfoTable	1.3.6.1.4.1.760.1.1.2.1.4		not-accessible	Table which contains information about the installed modems' versions.
mgmtAddr	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.4
mgmtSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.2
mibs	1.3.6.1.4.1.760.1
NTF modemAdded	1.3.6.1.4.1.760.1.1.2.1.0.3			This trap will be sent when a modem is added. The rack number and the index of the new modem is sent along with this trap.
modemAddr	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.3
modemEntry	1.3.6.1.4.1.760.1.1.2.1.3.1		not-accessible	The index of the table.
NTF modemRemoved	1.3.6.1.4.1.760.1.1.2.1.0.4			This trap will be sent when a modem in one of the slots is removed. The rack number and the index of the removed modem is sent along with this trap.
modemSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.1
otherModem	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.1
otherPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.1
outbandmgmtPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.5
p_ac_x_3v_20a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.11
p_ac_x_5v_20a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.2
p_ac_x_5v_30a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.3
p_dc_24v_5v_15a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.5
p_dc_48v_5v_18a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.4
p_dc_48v_5v_20a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.12
p_dc_48v_5v_30a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.6
p_dc_5v_3v_4a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.13
p_dc_5v_5v_5a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.14
pandatel	1.3.6.1.4.1.760
port_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.4
NTF portBackupAvailable	1.3.6.1.4.1.760.1.1.2.1.0.11			This trap will be sent when a second link can be used as backup. The rack number, index of the modem, and port number is sent along with this trap.
NTF portBackupDisabled	1.3.6.1.4.1.760.1.1.2.1.0.10			This trap will be sent when a modem in one of the slots leaves a backup status. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
NTF portBackupEnabled	1.3.6.1.4.1.760.1.1.2.1.0.9			This trap will be sent when a modem in one of the slots enters a backup status. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
NTF portBackupNotAvailable	1.3.6.1.4.1.760.1.1.2.1.0.12			This trap will be sent when there is no second link available as backup. The rack number, index of the modem, and port number is sent along with this trap.
INT portConnector	1.3.6.1.4.1.760.1.1.2.1.5.1.6	INTEGER	read-only	This entry indicates the connector type of the port.
NTF portDataPortChanged	1.3.6.1.4.1.760.1.1.2.1.0.13			This trap will be sent when the line port used for data transmission is changed. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
portEntry	1.3.6.1.4.1.760.1.1.2.1.5.1		not-accessible	The index of the table.
INT portInterfaceType	1.3.6.1.4.1.760.1.1.2.1.5.1.5	INTEGER	read-only	This entry indicates the type of interface of the port.
NTF portLoopDisabled	1.3.6.1.4.1.760.1.1.2.1.0.6			This trap will be sent when a modem in one of the slots disables a Loop. The rack number, index of the modem, and port number is sent along with this trap.
NTF portLoopEnabled	1.3.6.1.4.1.760.1.1.2.1.0.5			This trap will be sent when a modem in one of the slots enables a Loop. The rack number, index of the modem, and port number is sent along with this trap.
INT portLoopMode	1.3.6.1.4.1.760.1.1.2.1.5.1.7	INTEGER	read-write	This entry indicates the loop mode of the port.
INT portModem	1.3.6.1.4.1.760.1.1.2.1.5.1.2	INTEGER	read-only	The index of the modem to which this port belongs.
INT portPort	1.3.6.1.4.1.760.1.1.2.1.5.1.3	INTEGER	read-only	The index of the port.
INT portRack	1.3.6.1.4.1.760.1.1.2.1.5.1.1	INTEGER	read-only	The index of the rack where the modem to which this port belongs is installed.
portSignalEntry	1.3.6.1.4.1.760.1.1.2.1.6.1		not-accessible	The index of the table.
NTF portSignalStatusBad	1.3.6.1.4.1.760.1.1.2.1.0.8			This trap will be sent when a status signal of a modem port enters the 'bad' status. The rack number, index of the modem, and port number is sent along with this trap.
NTF portSignalStatusGood	1.3.6.1.4.1.760.1.1.2.1.0.7			This will be sent when a status signal of a modem port enters the 'good' status. The rack number, index of the modem, and port number is sent along with this trap.
INT portType	1.3.6.1.4.1.760.1.1.2.1.5.1.4	INTEGER	read-only	This entry indicates the type of the port.
products	1.3.6.1.4.1.760.1.1
ps_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.1
pS1_on_PS2_off	1.3.6.1.4.1.760.1.1.2.1.10.10000.6.2
pS1_on_PS2_on	1.3.6.1.4.1.760.1.1.2.1.10.10000.6.3
pS1_PS2_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.6.1
INT psignalModem	1.3.6.1.4.1.760.1.1.2.1.6.1.2	INTEGER	read-only	The index of the modem to which the port belongs that provides the signal.
INT psignalPort	1.3.6.1.4.1.760.1.1.2.1.6.1.3	INTEGER	read-only	The index of the port that provides the signal.
INT psignalRack	1.3.6.1.4.1.760.1.1.2.1.6.1.1	INTEGER	read-only	The index of the rack where the modem is installed to which the port belongs that provides the signal.
INT psignalStatus	1.3.6.1.4.1.760.1.1.2.1.6.1.5	INTEGER	read-only	This entry indicates the current status of the signal.
INT psignalTrap	1.3.6.1.4.1.760.1.1.2.1.6.1.6	INTEGER	read-write	This enables or disables traps. If Trap is enabled each transition of the signal status may cause a trap portSignalStatusGood/portSignalStatusBad.
INT psignalType	1.3.6.1.4.1.760.1.1.2.1.6.1.4	INTEGER	read-only	This entry indicates the signal type.
psonoff_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.6
psupply_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.5
psupplySlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.10
rack_10s_2c_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.8
rack_10s_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.2
rack_10s_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.4
rack_12s_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.3
rack_1s_1c_1hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.12
rack_3s_1c_1hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.13
rack_6s_9s_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.5
rack_8s_2c_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.10
rack_8s_4hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.7
rack_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.1
NTF rackAdded	1.3.6.1.4.1.760.1.1.2.1.0.1			This trap will be sent when a rack is added to the managed chassis. The rack index of the new rack is sent along with this trap.
STR rackDescription	1.3.6.1.4.1.760.1.1.2.1.2.1.3	DisplayString	read-only	A verbal description of the modem rack.
rackEntry	1.3.6.1.4.1.760.1.1.2.1.2.1		not-accessible	The index of the table.
INT rackModems	1.3.6.1.4.1.760.1.1.2.1.2.1.5	INTEGER	read-only	This entry shows the number of modems currently installed in the rack.
INT rackModemSlots	1.3.6.1.4.1.760.1.1.2.1.2.1.4	INTEGER	read-only	This entry shows the number of slots for modem cards in the rack.
INT rackPowerSupplies	1.3.6.1.4.1.760.1.1.2.1.2.1.7	INTEGER	read-only	This entry shows the number of power supplies currently installed in the rack.
INT rackPowerSupplySlots	1.3.6.1.4.1.760.1.1.2.1.2.1.6	INTEGER	read-only	This entry shows the number of slots for power supplies in the rack.
INT rackRack	1.3.6.1.4.1.760.1.1.2.1.2.1.1	INTEGER	read-only	The index of this particular modem rack in the stack. The index of the rack which contains the agent should have the number 1.
NTF rackRemoved	1.3.6.1.4.1.760.1.1.2.1.0.2			This trap will be sent when a rack is removed from the managed chassis. The rack index of the removed rack is sent along with this trap.
INT rackType	1.3.6.1.4.1.760.1.1.2.1.2.1.2	INTEGER	read-only	This entry shows the type number of the rack.
rc_control	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10004
remModemTable	1.3.6.1.4.1.760.1.1.2.1.9.3		not-accessible	Table which contains general information about all counterparts of the installed modems.
remPortEntry	1.3.6.1.4.1.760.1.1.2.1.9.5.1		not-accessible	The index of the table.
remPortSignalEntry	1.3.6.1.4.1.760.1.1.2.1.9.6.1		not-accessible	The index of the table.
remPortSignalTable	1.3.6.1.4.1.760.1.1.2.1.9.6		not-accessible	Table which contains information about all port status signals.
remPortTable	1.3.6.1.4.1.760.1.1.2.1.9.5		not-accessible	Table which contains information about all ports of the remote modem.
remVerInfoEntry	1.3.6.1.4.1.760.1.1.2.1.9.4.1		not-accessible	The index of the table.
remVerInfoTable	1.3.6.1.4.1.760.1.1.2.1.9.4		not-accessible	Table which contains information about the remote modems' versions.
STR rmdmDescription	1.3.6.1.4.1.760.1.1.2.1.9.3.1.3	DisplayString	read-only	A verbal description of the remote modem.
INT rmdmInterfacePorts	1.3.6.1.4.1.760.1.1.2.1.9.3.1.8	INTEGER	read-only	This entry indicates the number of interface ports of the remote modem. An interface port connects an external device.
INT rmdmLinePorts	1.3.6.1.4.1.760.1.1.2.1.9.3.1.9	INTEGER	read-only	This entry indicates the number of line ports of the modem. A line port connects the local counterpart of the remote modem.
INT rmdmModem	1.3.6.1.4.1.760.1.1.2.1.9.3.1.2	INTEGER	read-only	The index of the modem that the remote modem is linked to.
INT rmdmRack	1.3.6.1.4.1.760.1.1.2.1.9.3.1.1	INTEGER	read-only	This entry indicates the index of the rack where the modem is installed that the remote modem is linked to.
INT rmdmRemoteAccessStatus	1.3.6.1.4.1.760.1.1.2.1.9.3.1.7	INTEGER	read-only	This entry shows the access status of the modem. The standard value depends on the device. Some modems are always accessible, others are not accessible or can be switched to both modes (see 'mdmForcedRemoteAccess' in the specific modem MIB).
INT rmdmSelfTest	1.3.6.1.4.1.760.1.1.2.1.9.3.1.5	INTEGER	read-write	This entry enables the execution of a selftest. Write requests with values other than 'start' or 'cancel' will be rejected. The result will be found in SelfTestResult.
INT rmdmSelfTestResult	1.3.6.1.4.1.760.1.1.2.1.9.3.1.6	INTEGER	read-only	This indicates the result status of the last modem-dependent self test. After start, the status may change to 'running' before the first error that occured displays. If no error was detected the status changes to 'ok'.
STR rmdmUserName	1.3.6.1.4.1.760.1.1.2.1.9.3.1.4	DisplayString	read-write	A verbal description of the remote modem which can be changed by the manager.
rmodemEntry	1.3.6.1.4.1.760.1.1.2.1.9.3.1		not-accessible	The index of the table.
INT rportConnector	1.3.6.1.4.1.760.1.1.2.1.9.5.1.6	INTEGER	read-only	This entry indicates the connector type of the port.
INT rportInterfaceType	1.3.6.1.4.1.760.1.1.2.1.9.5.1.5	INTEGER	read-only	This entry indicates the type of interface of the port.
INT rportLoopMode	1.3.6.1.4.1.760.1.1.2.1.9.5.1.7	INTEGER	read-write	This entry indicates the loop mode of the port (remote, digital, line, off).
INT rportModem	1.3.6.1.4.1.760.1.1.2.1.9.5.1.2	INTEGER	read-only	The index of the local counterpart of the remote modem to which this port belongs.
INT rportPort	1.3.6.1.4.1.760.1.1.2.1.9.5.1.3	INTEGER	read-only	The index of the port.
INT rportRack	1.3.6.1.4.1.760.1.1.2.1.9.5.1.1	INTEGER	read-only	The index of the rack where the local counterpart of the remote modem is installed to which this port belongs.
INT rportType	1.3.6.1.4.1.760.1.1.2.1.9.5.1.4	INTEGER	read-only	This entry indicates the type of the port.
INT rpsignalModem	1.3.6.1.4.1.760.1.1.2.1.9.6.1.2	INTEGER	read-only	The index of the local counterpart of the remote modem.
INT rpsignalPort	1.3.6.1.4.1.760.1.1.2.1.9.6.1.3	INTEGER	read-only	The index of the port at the remote modem that provides the signal.
INT rpsignalRack	1.3.6.1.4.1.760.1.1.2.1.9.6.1.1	INTEGER	read-only	The index of the rack where the local counterpart of the remote modem is installed.
INT rpsignalStatus	1.3.6.1.4.1.760.1.1.2.1.9.6.1.5	INTEGER	read-only	This entry indicates the current status of the signal.
INT rpsignalType	1.3.6.1.4.1.760.1.1.2.1.9.6.1.4	INTEGER	read-only	This entry indicates the signal type.
rs485Port	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.7
STR rviArtNo	1.3.6.1.4.1.760.1.1.2.1.9.4.1.6	DisplayString	read-only	This entry indicates the article number of the remote modem.
STR rviFirmwVer	1.3.6.1.4.1.760.1.1.2.1.9.4.1.4	DisplayString	read-only	This entry indicates the firmware revision of the remote modem.
INT rviFrontVer	1.3.6.1.4.1.760.1.1.2.1.9.4.1.7	INTEGER	read-only	For factory purposes only.
INT rviModem	1.3.6.1.4.1.760.1.1.2.1.9.4.1.2	INTEGER	read-only	The index of the modem that the remote modem is linked to.
INT rviRack	1.3.6.1.4.1.760.1.1.2.1.9.4.1.1	INTEGER	read-only	The index of the rack where the modem is installed that the remote modem is linked to.
STR rviSerialNumber	1.3.6.1.4.1.760.1.1.2.1.9.4.1.8	DisplayString	read-only	This entry indicates the serial number of the remote modem.
INT rviType	1.3.6.1.4.1.760.1.1.2.1.9.4.1.3	INTEGER	read-only	This entry indicates the type of the remote modem.
STR rviUnitRel	1.3.6.1.4.1.760.1.1.2.1.9.4.1.5	DisplayString	read-only	This entry indicates the hardware version and revision of the remote modem.
slot_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.3
verInfoEntry	1.3.6.1.4.1.760.1.1.2.1.4.1		not-accessible	The index of the table.
STR viArtNo	1.3.6.1.4.1.760.1.1.2.1.4.1.6	DisplayString	read-only	This entry indicates the article number of the modem.
STR viFirmwVer	1.3.6.1.4.1.760.1.1.2.1.4.1.4	DisplayString	read-only	This entry indicates the firmware revision of the modem.
INT viFrontVer	1.3.6.1.4.1.760.1.1.2.1.4.1.7	INTEGER	read-only	For factory purposes only.
INT viModem	1.3.6.1.4.1.760.1.1.2.1.4.1.2	INTEGER	read-only	The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
INT viRack	1.3.6.1.4.1.760.1.1.2.1.4.1.1	INTEGER	read-only	The index of the rack where the modem is installed.
STR viSerialNumber	1.3.6.1.4.1.760.1.1.2.1.4.1.8	DisplayString	read-only	This entry indicates the serial number of the modem.
INT viType	1.3.6.1.4.1.760.1.1.2.1.4.1.3	INTEGER	read-only	This entry indicates the type of the modem.
STR viUnitRel	1.3.6.1.4.1.760.1.1.2.1.4.1.5	DisplayString	read-only	This entry indicates the hardware version and revision of the modem.
vt100mgmtPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.4
wan_products	1.3.6.1.4.1.760.1.1.2
wdmSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.5

OID symbolic	OID numeric	Type	Access	Description
pandatel	1.3.6.1.4.1.760
mibs	1.3.6.1.4.1.760.1
products	1.3.6.1.4.1.760.1.1
wan_products	1.3.6.1.4.1.760.1.1.2
mdm_mgmt	1.3.6.1.4.1.760.1.1.2.1
NTF rackAdded	1.3.6.1.4.1.760.1.1.2.1.0.1			This trap will be sent when a rack is added to the managed chassis. The rack index of the new rack is sent along with this trap.
NTF rackRemoved	1.3.6.1.4.1.760.1.1.2.1.0.2			This trap will be sent when a rack is removed from the managed chassis. The rack index of the removed rack is sent along with this trap.
NTF modemAdded	1.3.6.1.4.1.760.1.1.2.1.0.3			This trap will be sent when a modem is added. The rack number and the index of the new modem is sent along with this trap.
NTF modemRemoved	1.3.6.1.4.1.760.1.1.2.1.0.4			This trap will be sent when a modem in one of the slots is removed. The rack number and the index of the removed modem is sent along with this trap.
NTF portLoopEnabled	1.3.6.1.4.1.760.1.1.2.1.0.5			This trap will be sent when a modem in one of the slots enables a Loop. The rack number, index of the modem, and port number is sent along with this trap.
NTF portLoopDisabled	1.3.6.1.4.1.760.1.1.2.1.0.6			This trap will be sent when a modem in one of the slots disables a Loop. The rack number, index of the modem, and port number is sent along with this trap.
NTF portSignalStatusGood	1.3.6.1.4.1.760.1.1.2.1.0.7			This will be sent when a status signal of a modem port enters the 'good' status. The rack number, index of the modem, and port number is sent along with this trap.
NTF portSignalStatusBad	1.3.6.1.4.1.760.1.1.2.1.0.8			This trap will be sent when a status signal of a modem port enters the 'bad' status. The rack number, index of the modem, and port number is sent along with this trap.
NTF portBackupEnabled	1.3.6.1.4.1.760.1.1.2.1.0.9			This trap will be sent when a modem in one of the slots enters a backup status. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
NTF portBackupDisabled	1.3.6.1.4.1.760.1.1.2.1.0.10			This trap will be sent when a modem in one of the slots leaves a backup status. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
NTF portBackupAvailable	1.3.6.1.4.1.760.1.1.2.1.0.11			This trap will be sent when a second link can be used as backup. The rack number, index of the modem, and port number is sent along with this trap.
NTF portBackupNotAvailable	1.3.6.1.4.1.760.1.1.2.1.0.12			This trap will be sent when there is no second link available as backup. The rack number, index of the modem, and port number is sent along with this trap.
NTF portDataPortChanged	1.3.6.1.4.1.760.1.1.2.1.0.13			This trap will be sent when the line port used for data transmission is changed. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
mdmGroup	1.3.6.1.4.1.760.1.1.2.1.1
INT mdmInstalledRacks	1.3.6.1.4.1.760.1.1.2.1.1.1	INTEGER	read-only	This is the number of currently installed modem racks.
INT mdmInstalledModems	1.3.6.1.4.1.760.1.1.2.1.1.2	INTEGER	read-only	This is the number of currently installed modems
INT mdmLoopModeTraps	1.3.6.1.4.1.760.1.1.2.1.1.3	INTEGER	read-write	This enables or disables traps generated by a Loop Mode status change at any local modem port of one of the installed modems (values: disable, enable).
STR mdmCurrentDate	1.3.6.1.4.1.760.1.1.2.1.1.13	DisplayString	read-write	This indicate the current date as 'mm/dd/yy'. The date will be used for local management.
STR mdmCurrentTime	1.3.6.1.4.1.760.1.1.2.1.1.14	DisplayString	read-write	This indicate the current time as 'hh:mm:ss'. The time will be used for local management.
mdmRackTable	1.3.6.1.4.1.760.1.1.2.1.2		not-accessible	Table which contains information about the installed racks.
rackEntry	1.3.6.1.4.1.760.1.1.2.1.2.1		not-accessible	The index of the table.
INT rackRack	1.3.6.1.4.1.760.1.1.2.1.2.1.1	INTEGER	read-only	The index of this particular modem rack in the stack. The index of the rack which contains the agent should have the number 1.
INT rackType	1.3.6.1.4.1.760.1.1.2.1.2.1.2	INTEGER	read-only	This entry shows the type number of the rack.
STR rackDescription	1.3.6.1.4.1.760.1.1.2.1.2.1.3	DisplayString	read-only	A verbal description of the modem rack.
INT rackModemSlots	1.3.6.1.4.1.760.1.1.2.1.2.1.4	INTEGER	read-only	This entry shows the number of slots for modem cards in the rack.
INT rackModems	1.3.6.1.4.1.760.1.1.2.1.2.1.5	INTEGER	read-only	This entry shows the number of modems currently installed in the rack.
INT rackPowerSupplySlots	1.3.6.1.4.1.760.1.1.2.1.2.1.6	INTEGER	read-only	This entry shows the number of slots for power supplies in the rack.
INT rackPowerSupplies	1.3.6.1.4.1.760.1.1.2.1.2.1.7	INTEGER	read-only	This entry shows the number of power supplies currently installed in the rack.
mdmModemTable	1.3.6.1.4.1.760.1.1.2.1.3		not-accessible	Table which contains general information about the installed modems.
modemEntry	1.3.6.1.4.1.760.1.1.2.1.3.1		not-accessible	The index of the table.
INT mdmRack	1.3.6.1.4.1.760.1.1.2.1.3.1.1	INTEGER	read-only	The index of the rack where the modem is installed.
INT mdmModem	1.3.6.1.4.1.760.1.1.2.1.3.1.2	INTEGER	read-only	The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
STR mdmDescription	1.3.6.1.4.1.760.1.1.2.1.3.1.3	DisplayString	read-only	A verbal description of the modem.
STR mdmUserName	1.3.6.1.4.1.760.1.1.2.1.3.1.4	DisplayString	read-write	A verbal description of the modem which can be changed by the manager.
INT mdmSelfTest	1.3.6.1.4.1.760.1.1.2.1.3.1.5	INTEGER	read-write	This entry enables the execution of a selftest. Write requests with values other than 'start' or 'cancel' will be rejected. The result will be found in mdmSelfTestResult.
INT mdmSelfTestResult	1.3.6.1.4.1.760.1.1.2.1.3.1.6	INTEGER	read-only	This entry shows the result status of the last modem-dependent self test. After start, the status may change to 'running' before the first error that occured is displayed. If no error was detected the status changes to 'ok'.
INT mdmRemoteAccessStatus	1.3.6.1.4.1.760.1.1.2.1.3.1.7	INTEGER	read-only	This entry shows the access status to the remote counterpart of the modem. The standard value depends on the device. Some remote modems are always accessible, others are not accessible or can be switched to both modes (see 'mdmForcedRemoteAccess' in the specific modem MIB).
INT mdmInterfacePorts	1.3.6.1.4.1.760.1.1.2.1.3.1.8	INTEGER	read-only	This entry indicates the number of interface ports of the modem. An interface port connects an external device.
INT mdmLinePorts	1.3.6.1.4.1.760.1.1.2.1.3.1.9	INTEGER	read-only	This entry indicates the number of line ports of the modem. A line port connects a remote modem.
mdmVerInfoTable	1.3.6.1.4.1.760.1.1.2.1.4		not-accessible	Table which contains information about the installed modems' versions.
verInfoEntry	1.3.6.1.4.1.760.1.1.2.1.4.1		not-accessible	The index of the table.
INT viRack	1.3.6.1.4.1.760.1.1.2.1.4.1.1	INTEGER	read-only	The index of the rack where the modem is installed.
INT viModem	1.3.6.1.4.1.760.1.1.2.1.4.1.2	INTEGER	read-only	The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
INT viType	1.3.6.1.4.1.760.1.1.2.1.4.1.3	INTEGER	read-only	This entry indicates the type of the modem.
STR viFirmwVer	1.3.6.1.4.1.760.1.1.2.1.4.1.4	DisplayString	read-only	This entry indicates the firmware revision of the modem.
STR viUnitRel	1.3.6.1.4.1.760.1.1.2.1.4.1.5	DisplayString	read-only	This entry indicates the hardware version and revision of the modem.
STR viArtNo	1.3.6.1.4.1.760.1.1.2.1.4.1.6	DisplayString	read-only	This entry indicates the article number of the modem.
INT viFrontVer	1.3.6.1.4.1.760.1.1.2.1.4.1.7	INTEGER	read-only	For factory purposes only.
STR viSerialNumber	1.3.6.1.4.1.760.1.1.2.1.4.1.8	DisplayString	read-only	This entry indicates the serial number of the modem.
mdmPortTable	1.3.6.1.4.1.760.1.1.2.1.5		not-accessible	Table which contains information about all ports.
portEntry	1.3.6.1.4.1.760.1.1.2.1.5.1		not-accessible	The index of the table.
INT portRack	1.3.6.1.4.1.760.1.1.2.1.5.1.1	INTEGER	read-only	The index of the rack where the modem to which this port belongs is installed.
INT portModem	1.3.6.1.4.1.760.1.1.2.1.5.1.2	INTEGER	read-only	The index of the modem to which this port belongs.
INT portPort	1.3.6.1.4.1.760.1.1.2.1.5.1.3	INTEGER	read-only	The index of the port.
INT portType	1.3.6.1.4.1.760.1.1.2.1.5.1.4	INTEGER	read-only	This entry indicates the type of the port.
INT portInterfaceType	1.3.6.1.4.1.760.1.1.2.1.5.1.5	INTEGER	read-only	This entry indicates the type of interface of the port.
INT portConnector	1.3.6.1.4.1.760.1.1.2.1.5.1.6	INTEGER	read-only	This entry indicates the connector type of the port.
INT portLoopMode	1.3.6.1.4.1.760.1.1.2.1.5.1.7	INTEGER	read-write	This entry indicates the loop mode of the port.
mdmPortSignalTable	1.3.6.1.4.1.760.1.1.2.1.6		not-accessible	Table which contains information about all port status signals.
portSignalEntry	1.3.6.1.4.1.760.1.1.2.1.6.1		not-accessible	The index of the table.
INT psignalRack	1.3.6.1.4.1.760.1.1.2.1.6.1.1	INTEGER	read-only	The index of the rack where the modem is installed to which the port belongs that provides the signal.
INT psignalModem	1.3.6.1.4.1.760.1.1.2.1.6.1.2	INTEGER	read-only	The index of the modem to which the port belongs that provides the signal.
INT psignalPort	1.3.6.1.4.1.760.1.1.2.1.6.1.3	INTEGER	read-only	The index of the port that provides the signal.
INT psignalType	1.3.6.1.4.1.760.1.1.2.1.6.1.4	INTEGER	read-only	This entry indicates the signal type.
INT psignalStatus	1.3.6.1.4.1.760.1.1.2.1.6.1.5	INTEGER	read-only	This entry indicates the current status of the signal.
INT psignalTrap	1.3.6.1.4.1.760.1.1.2.1.6.1.6	INTEGER	read-write	This enables or disables traps. If Trap is enabled each transition of the signal status may cause a trap portSignalStatusGood/portSignalStatusBad.
mdmBERTTable	1.3.6.1.4.1.760.1.1.2.1.7		not-accessible	Table which contains information about all performable bit error rate tests.
bertEntry	1.3.6.1.4.1.760.1.1.2.1.7.1		not-accessible	The index of thetable.
INT bertRack	1.3.6.1.4.1.760.1.1.2.1.7.1.1	INTEGER	read-only	The index of the rack where the modem is installed.
INT bertModem	1.3.6.1.4.1.760.1.1.2.1.7.1.2	INTEGER	read-only	The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
INT bertPort	1.3.6.1.4.1.760.1.1.2.1.7.1.3	INTEGER	read-write	The index of the port where the BER test will be performed. The modem can only perform one test at a time. The test can only be performed on a subset of ports, usually the line ports. Write requests with different port numbers will be rejected. Write requests with valid line port numbers will be rejected while the BER test is running.
INT bertBERTest	1.3.6.1.4.1.760.1.1.2.1.7.1.4	INTEGER	read-write	This entry enables the execution of a BER test. Write requests with values other than 'start' or 'stop' will be rejected.
INT bertStatus	1.3.6.1.4.1.760.1.1.2.1.7.1.5	INTEGER	read-only	This entry indicates the status of the BER test.
CTR bertRunTime	1.3.6.1.4.1.760.1.1.2.1.7.1.6	Counter	read-only	This entry indicates the duration of the BER test in seconds.
CTR bertInErrorTime	1.3.6.1.4.1.760.1.1.2.1.7.1.7	Counter	read-only	This entry shows the duration of erroneous test transmission in seconds.
CTR bertErrorFreeTime	1.3.6.1.4.1.760.1.1.2.1.7.1.8	Counter	read-only	This entry shows the duration of error-free test transmission in seconds.
CTR bertKbitsRecWrapped	1.3.6.1.4.1.760.1.1.2.1.7.1.9	Counter	read-only	This is the number the bertKbitsReceived counter has wrapped.
CTR bertKbitsReceived	1.3.6.1.4.1.760.1.1.2.1.7.1.10	Counter	read-only	This entry indicates the number of Kbits received during the test. When the counter wraps the bertKbitRecWrapped increases by one.
CTR bertErrors	1.3.6.1.4.1.760.1.1.2.1.7.1.11	Counter	read-only	This entry indicates the number of errors detected during the test.
CTR bertSyncLosts	1.3.6.1.4.1.760.1.1.2.1.7.1.12	Counter	read-only	This entry indicates the number of pattern sync losts detected during the test.
INT bertSyncStatus	1.3.6.1.4.1.760.1.1.2.1.7.1.13	INTEGER	read-only	This entry indicates the current pattern sync status.
STR bertBitErrorRate	1.3.6.1.4.1.760.1.1.2.1.7.1.14	DisplayString	read-only	This entry indicates the bit error rate. It is provided as a string in the format 'd.ddE+/-dd'. Float scanf routines are capable of interpreting the string in the correct manner.
mdmRemoteAccess	1.3.6.1.4.1.760.1.1.2.1.9
remModemTable	1.3.6.1.4.1.760.1.1.2.1.9.3		not-accessible	Table which contains general information about all counterparts of the installed modems.
rmodemEntry	1.3.6.1.4.1.760.1.1.2.1.9.3.1		not-accessible	The index of the table.
INT rmdmRack	1.3.6.1.4.1.760.1.1.2.1.9.3.1.1	INTEGER	read-only	This entry indicates the index of the rack where the modem is installed that the remote modem is linked to.
INT rmdmModem	1.3.6.1.4.1.760.1.1.2.1.9.3.1.2	INTEGER	read-only	The index of the modem that the remote modem is linked to.
STR rmdmDescription	1.3.6.1.4.1.760.1.1.2.1.9.3.1.3	DisplayString	read-only	A verbal description of the remote modem.
STR rmdmUserName	1.3.6.1.4.1.760.1.1.2.1.9.3.1.4	DisplayString	read-write	A verbal description of the remote modem which can be changed by the manager.
INT rmdmSelfTest	1.3.6.1.4.1.760.1.1.2.1.9.3.1.5	INTEGER	read-write	This entry enables the execution of a selftest. Write requests with values other than 'start' or 'cancel' will be rejected. The result will be found in SelfTestResult.
INT rmdmSelfTestResult	1.3.6.1.4.1.760.1.1.2.1.9.3.1.6	INTEGER	read-only	This indicates the result status of the last modem-dependent self test. After start, the status may change to 'running' before the first error that occured displays. If no error was detected the status changes to 'ok'.
INT rmdmRemoteAccessStatus	1.3.6.1.4.1.760.1.1.2.1.9.3.1.7	INTEGER	read-only	This entry shows the access status of the modem. The standard value depends on the device. Some modems are always accessible, others are not accessible or can be switched to both modes (see 'mdmForcedRemoteAccess' in the specific modem MIB).
INT rmdmInterfacePorts	1.3.6.1.4.1.760.1.1.2.1.9.3.1.8	INTEGER	read-only	This entry indicates the number of interface ports of the remote modem. An interface port connects an external device.
INT rmdmLinePorts	1.3.6.1.4.1.760.1.1.2.1.9.3.1.9	INTEGER	read-only	This entry indicates the number of line ports of the modem. A line port connects the local counterpart of the remote modem.
remVerInfoTable	1.3.6.1.4.1.760.1.1.2.1.9.4		not-accessible	Table which contains information about the remote modems' versions.
remVerInfoEntry	1.3.6.1.4.1.760.1.1.2.1.9.4.1		not-accessible	The index of the table.
INT rviRack	1.3.6.1.4.1.760.1.1.2.1.9.4.1.1	INTEGER	read-only	The index of the rack where the modem is installed that the remote modem is linked to.
INT rviModem	1.3.6.1.4.1.760.1.1.2.1.9.4.1.2	INTEGER	read-only	The index of the modem that the remote modem is linked to.
INT rviType	1.3.6.1.4.1.760.1.1.2.1.9.4.1.3	INTEGER	read-only	This entry indicates the type of the remote modem.
STR rviFirmwVer	1.3.6.1.4.1.760.1.1.2.1.9.4.1.4	DisplayString	read-only	This entry indicates the firmware revision of the remote modem.
STR rviUnitRel	1.3.6.1.4.1.760.1.1.2.1.9.4.1.5	DisplayString	read-only	This entry indicates the hardware version and revision of the remote modem.
STR rviArtNo	1.3.6.1.4.1.760.1.1.2.1.9.4.1.6	DisplayString	read-only	This entry indicates the article number of the remote modem.
INT rviFrontVer	1.3.6.1.4.1.760.1.1.2.1.9.4.1.7	INTEGER	read-only	For factory purposes only.
STR rviSerialNumber	1.3.6.1.4.1.760.1.1.2.1.9.4.1.8	DisplayString	read-only	This entry indicates the serial number of the remote modem.
remPortTable	1.3.6.1.4.1.760.1.1.2.1.9.5		not-accessible	Table which contains information about all ports of the remote modem.
remPortEntry	1.3.6.1.4.1.760.1.1.2.1.9.5.1		not-accessible	The index of the table.
INT rportRack	1.3.6.1.4.1.760.1.1.2.1.9.5.1.1	INTEGER	read-only	The index of the rack where the local counterpart of the remote modem is installed to which this port belongs.
INT rportModem	1.3.6.1.4.1.760.1.1.2.1.9.5.1.2	INTEGER	read-only	The index of the local counterpart of the remote modem to which this port belongs.
INT rportPort	1.3.6.1.4.1.760.1.1.2.1.9.5.1.3	INTEGER	read-only	The index of the port.
INT rportType	1.3.6.1.4.1.760.1.1.2.1.9.5.1.4	INTEGER	read-only	This entry indicates the type of the port.
INT rportInterfaceType	1.3.6.1.4.1.760.1.1.2.1.9.5.1.5	INTEGER	read-only	This entry indicates the type of interface of the port.
INT rportConnector	1.3.6.1.4.1.760.1.1.2.1.9.5.1.6	INTEGER	read-only	This entry indicates the connector type of the port.
INT rportLoopMode	1.3.6.1.4.1.760.1.1.2.1.9.5.1.7	INTEGER	read-write	This entry indicates the loop mode of the port (remote, digital, line, off).
remPortSignalTable	1.3.6.1.4.1.760.1.1.2.1.9.6		not-accessible	Table which contains information about all port status signals.
remPortSignalEntry	1.3.6.1.4.1.760.1.1.2.1.9.6.1		not-accessible	The index of the table.
INT rpsignalRack	1.3.6.1.4.1.760.1.1.2.1.9.6.1.1	INTEGER	read-only	The index of the rack where the local counterpart of the remote modem is installed.
INT rpsignalModem	1.3.6.1.4.1.760.1.1.2.1.9.6.1.2	INTEGER	read-only	The index of the local counterpart of the remote modem.
INT rpsignalPort	1.3.6.1.4.1.760.1.1.2.1.9.6.1.3	INTEGER	read-only	The index of the port at the remote modem that provides the signal.
INT rpsignalType	1.3.6.1.4.1.760.1.1.2.1.9.6.1.4	INTEGER	read-only	This entry indicates the signal type.
INT rpsignalStatus	1.3.6.1.4.1.760.1.1.2.1.9.6.1.5	INTEGER	read-only	This entry indicates the current status of the signal.
mdmSpecifics	1.3.6.1.4.1.760.1.1.2.1.10
mdm_oid	1.3.6.1.4.1.760.1.1.2.1.10.10000
comp_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.1
rack_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.1
rack_10s_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.2
rack_12s_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.3
rack_10s_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.4
rack_6s_9s_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.5
device_stack_15s	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.6
rack_8s_4hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.7
rack_10s_2c_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.8
hs_rack_10s_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.9
rack_8s_2c_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.10
hs_rack_3s_1c_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.11
rack_1s_1c_1hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.12
rack_3s_1c_1hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.13
device_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.2
otherModem	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.1
cms_snmp_master	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10001
cms_slave	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10002
cms_intelligent_slave	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10003
rc_control	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10004
slot_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.3
modemSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.1
mgmtSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.2
modemAddr	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.3
mgmtAddr	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.4
wdmSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.5
controlSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.6
psupplySlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.10
port_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.4
otherPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.1
interfacePort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.2
linePort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.3
vt100mgmtPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.4
outbandmgmtPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.5
backupPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.6
rs485Port	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.7
psupply_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.5
ps_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.1
p_ac_x_5v_20a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.2
p_ac_x_5v_30a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.3
p_dc_48v_5v_18a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.4
p_dc_24v_5v_15a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.5
p_dc_48v_5v_30a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.6
b_ac_x_5v_6a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.7
b_dc_48v_5v_lc	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.8
b_dc_48v_5v_hc	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.9
b_dc_24v_5v_su	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.10
p_ac_x_3v_20a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.11
p_dc_48v_5v_20a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.12
p_dc_5v_3v_4a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.13
p_dc_5v_5v_5a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.14
psonoff_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.6
pS1_PS2_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.6.1
pS1_on_PS2_off	1.3.6.1.4.1.760.1.1.2.1.10.10000.6.2
pS1_on_PS2_on	1.3.6.1.4.1.760.1.1.2.1.10.10000.6.3
fanonoff_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.7
fAN1_FAN2_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.1
fAN1_off_FAN2_off	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.2
fAN1_on_FAN2_off	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.3
fAN1_off_FAN2_on	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.4
fAN1_on_FAN2_on	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.5
mdmMgmtIfGroup	1.3.6.1.4.1.760.1.1.2.1.20
INT mdmIfType	1.3.6.1.4.1.760.1.1.2.1.20.1	INTEGER	read-only	This variable shows the agent's interface type.
INT mdmIfProtocol	1.3.6.1.4.1.760.1.1.2.1.20.2	INTEGER	read-only	This variable shows the agent's protocol type.
INT mdmIfDataRate	1.3.6.1.4.1.760.1.1.2.1.20.3	INTEGER	read-only	This variable shows the agent's data rate in bps.
INT mdmIfDialEnable	1.3.6.1.4.1.760.1.1.2.1.20.4	INTEGER	read-write	This variable enables the initialization of a dial modem in case of alarm. The following variables (5 to 10) are active only if this variable is enabled.
STR mdmIfInitString	1.3.6.1.4.1.760.1.1.2.1.20.5	DisplayString	read-write	This variable defines an init string which is generated in case of alarm to configure an external Hayes compatible modem.
STR mdmIfDialString	1.3.6.1.4.1.760.1.1.2.1.20.6	DisplayString	read-write	This variable defines a modem command which is generated in case of alarm to dial-up a remote NMS station. If the dial string is not defined neither the init string nor the dial string is generated.
INT mdmIfSendTTL	1.3.6.1.4.1.760.1.1.2.1.20.7	INTEGER	read-write	This variable defines the TTL (time to live) in seconds. After that time the generated traps will be deleted from the buffer. If the value is '0' the traps will remain in the buffer.
INT mdmIfDialTimeout	1.3.6.1.4.1.760.1.1.2.1.20.8	INTEGER	read-write	This variable defines a dial timeout for the modem in seconds.
INT mdmIfRedialPause	1.3.6.1.4.1.760.1.1.2.1.20.9	INTEGER	read-write	This variable defines the duration of a redial pause in seconds.
INT mdmIfIdlePeriodBeforeDisconnect	1.3.6.1.4.1.760.1.1.2.1.20.10	INTEGER	read-write	This variable defines the period of time before disconnecting in seconds. If the value is '0' the modem will remain connected.

Counter (7)
CTR bertErrorFreeTime	1.3.6.1.4.1.760.1.1.2.1.7.1.8	Counter	read-only	This entry shows the duration of error-free test transmission in seconds.
CTR bertErrors	1.3.6.1.4.1.760.1.1.2.1.7.1.11	Counter	read-only	This entry indicates the number of errors detected during the test.
CTR bertInErrorTime	1.3.6.1.4.1.760.1.1.2.1.7.1.7	Counter	read-only	This entry shows the duration of erroneous test transmission in seconds.
CTR bertKbitsReceived	1.3.6.1.4.1.760.1.1.2.1.7.1.10	Counter	read-only	This entry indicates the number of Kbits received during the test. When the counter wraps the bertKbitRecWrapped increases by one.
CTR bertKbitsRecWrapped	1.3.6.1.4.1.760.1.1.2.1.7.1.9	Counter	read-only	This is the number the bertKbitsReceived counter has wrapped.
CTR bertRunTime	1.3.6.1.4.1.760.1.1.2.1.7.1.6	Counter	read-only	This entry indicates the duration of the BER test in seconds.
CTR bertSyncLosts	1.3.6.1.4.1.760.1.1.2.1.7.1.12	Counter	read-only	This entry indicates the number of pattern sync losts detected during the test.
DisplayString (18)
STR bertBitErrorRate	1.3.6.1.4.1.760.1.1.2.1.7.1.14	DisplayString	read-only	This entry indicates the bit error rate. It is provided as a string in the format 'd.ddE+/-dd'. Float scanf routines are capable of interpreting the string in the correct manner.
STR mdmCurrentDate	1.3.6.1.4.1.760.1.1.2.1.1.13	DisplayString	read-write	This indicate the current date as 'mm/dd/yy'. The date will be used for local management.
STR mdmCurrentTime	1.3.6.1.4.1.760.1.1.2.1.1.14	DisplayString	read-write	This indicate the current time as 'hh:mm:ss'. The time will be used for local management.
STR mdmDescription	1.3.6.1.4.1.760.1.1.2.1.3.1.3	DisplayString	read-only	A verbal description of the modem.
STR mdmIfDialString	1.3.6.1.4.1.760.1.1.2.1.20.6	DisplayString	read-write	This variable defines a modem command which is generated in case of alarm to dial-up a remote NMS station. If the dial string is not defined neither the init string nor the dial string is generated.
STR mdmIfInitString	1.3.6.1.4.1.760.1.1.2.1.20.5	DisplayString	read-write	This variable defines an init string which is generated in case of alarm to configure an external Hayes compatible modem.
STR mdmUserName	1.3.6.1.4.1.760.1.1.2.1.3.1.4	DisplayString	read-write	A verbal description of the modem which can be changed by the manager.
STR rackDescription	1.3.6.1.4.1.760.1.1.2.1.2.1.3	DisplayString	read-only	A verbal description of the modem rack.
STR rmdmDescription	1.3.6.1.4.1.760.1.1.2.1.9.3.1.3	DisplayString	read-only	A verbal description of the remote modem.
STR rmdmUserName	1.3.6.1.4.1.760.1.1.2.1.9.3.1.4	DisplayString	read-write	A verbal description of the remote modem which can be changed by the manager.
STR rviArtNo	1.3.6.1.4.1.760.1.1.2.1.9.4.1.6	DisplayString	read-only	This entry indicates the article number of the remote modem.
STR rviFirmwVer	1.3.6.1.4.1.760.1.1.2.1.9.4.1.4	DisplayString	read-only	This entry indicates the firmware revision of the remote modem.
STR rviSerialNumber	1.3.6.1.4.1.760.1.1.2.1.9.4.1.8	DisplayString	read-only	This entry indicates the serial number of the remote modem.
STR rviUnitRel	1.3.6.1.4.1.760.1.1.2.1.9.4.1.5	DisplayString	read-only	This entry indicates the hardware version and revision of the remote modem.
STR viArtNo	1.3.6.1.4.1.760.1.1.2.1.4.1.6	DisplayString	read-only	This entry indicates the article number of the modem.
STR viFirmwVer	1.3.6.1.4.1.760.1.1.2.1.4.1.4	DisplayString	read-only	This entry indicates the firmware revision of the modem.
STR viSerialNumber	1.3.6.1.4.1.760.1.1.2.1.4.1.8	DisplayString	read-only	This entry indicates the serial number of the modem.
STR viUnitRel	1.3.6.1.4.1.760.1.1.2.1.4.1.5	DisplayString	read-only	This entry indicates the hardware version and revision of the modem.
INTEGER (70)
INT bertBERTest	1.3.6.1.4.1.760.1.1.2.1.7.1.4	INTEGER	read-write	This entry enables the execution of a BER test. Write requests with values other than 'start' or 'stop' will be rejected.
INT bertModem	1.3.6.1.4.1.760.1.1.2.1.7.1.2	INTEGER	read-only	The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
INT bertPort	1.3.6.1.4.1.760.1.1.2.1.7.1.3	INTEGER	read-write	The index of the port where the BER test will be performed. The modem can only perform one test at a time. The test can only be performed on a subset of ports, usually the line ports. Write requests with different port numbers will be rejected. Write requests with valid line port numbers will be rejected while the BER test is running.
INT bertRack	1.3.6.1.4.1.760.1.1.2.1.7.1.1	INTEGER	read-only	The index of the rack where the modem is installed.
INT bertStatus	1.3.6.1.4.1.760.1.1.2.1.7.1.5	INTEGER	read-only	This entry indicates the status of the BER test.
INT bertSyncStatus	1.3.6.1.4.1.760.1.1.2.1.7.1.13	INTEGER	read-only	This entry indicates the current pattern sync status.
INT mdmIfDataRate	1.3.6.1.4.1.760.1.1.2.1.20.3	INTEGER	read-only	This variable shows the agent's data rate in bps.
INT mdmIfDialEnable	1.3.6.1.4.1.760.1.1.2.1.20.4	INTEGER	read-write	This variable enables the initialization of a dial modem in case of alarm. The following variables (5 to 10) are active only if this variable is enabled.
INT mdmIfDialTimeout	1.3.6.1.4.1.760.1.1.2.1.20.8	INTEGER	read-write	This variable defines a dial timeout for the modem in seconds.
INT mdmIfIdlePeriodBeforeDisconnect	1.3.6.1.4.1.760.1.1.2.1.20.10	INTEGER	read-write	This variable defines the period of time before disconnecting in seconds. If the value is '0' the modem will remain connected.
INT mdmIfProtocol	1.3.6.1.4.1.760.1.1.2.1.20.2	INTEGER	read-only	This variable shows the agent's protocol type.
INT mdmIfRedialPause	1.3.6.1.4.1.760.1.1.2.1.20.9	INTEGER	read-write	This variable defines the duration of a redial pause in seconds.
INT mdmIfSendTTL	1.3.6.1.4.1.760.1.1.2.1.20.7	INTEGER	read-write	This variable defines the TTL (time to live) in seconds. After that time the generated traps will be deleted from the buffer. If the value is '0' the traps will remain in the buffer.
INT mdmIfType	1.3.6.1.4.1.760.1.1.2.1.20.1	INTEGER	read-only	This variable shows the agent's interface type.
INT mdmInstalledModems	1.3.6.1.4.1.760.1.1.2.1.1.2	INTEGER	read-only	This is the number of currently installed modems
INT mdmInstalledRacks	1.3.6.1.4.1.760.1.1.2.1.1.1	INTEGER	read-only	This is the number of currently installed modem racks.
INT mdmInterfacePorts	1.3.6.1.4.1.760.1.1.2.1.3.1.8	INTEGER	read-only	This entry indicates the number of interface ports of the modem. An interface port connects an external device.
INT mdmLinePorts	1.3.6.1.4.1.760.1.1.2.1.3.1.9	INTEGER	read-only	This entry indicates the number of line ports of the modem. A line port connects a remote modem.
INT mdmLoopModeTraps	1.3.6.1.4.1.760.1.1.2.1.1.3	INTEGER	read-write	This enables or disables traps generated by a Loop Mode status change at any local modem port of one of the installed modems (values: disable, enable).
INT mdmModem	1.3.6.1.4.1.760.1.1.2.1.3.1.2	INTEGER	read-only	The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
INT mdmRack	1.3.6.1.4.1.760.1.1.2.1.3.1.1	INTEGER	read-only	The index of the rack where the modem is installed.
INT mdmRemoteAccessStatus	1.3.6.1.4.1.760.1.1.2.1.3.1.7	INTEGER	read-only	This entry shows the access status to the remote counterpart of the modem. The standard value depends on the device. Some remote modems are always accessible, others are not accessible or can be switched to both modes (see 'mdmForcedRemoteAccess' in the specific modem MIB).
INT mdmSelfTest	1.3.6.1.4.1.760.1.1.2.1.3.1.5	INTEGER	read-write	This entry enables the execution of a selftest. Write requests with values other than 'start' or 'cancel' will be rejected. The result will be found in mdmSelfTestResult.
INT mdmSelfTestResult	1.3.6.1.4.1.760.1.1.2.1.3.1.6	INTEGER	read-only	This entry shows the result status of the last modem-dependent self test. After start, the status may change to 'running' before the first error that occured is displayed. If no error was detected the status changes to 'ok'.
INT portConnector	1.3.6.1.4.1.760.1.1.2.1.5.1.6	INTEGER	read-only	This entry indicates the connector type of the port.
INT portInterfaceType	1.3.6.1.4.1.760.1.1.2.1.5.1.5	INTEGER	read-only	This entry indicates the type of interface of the port.
INT portLoopMode	1.3.6.1.4.1.760.1.1.2.1.5.1.7	INTEGER	read-write	This entry indicates the loop mode of the port.
INT portModem	1.3.6.1.4.1.760.1.1.2.1.5.1.2	INTEGER	read-only	The index of the modem to which this port belongs.
INT portPort	1.3.6.1.4.1.760.1.1.2.1.5.1.3	INTEGER	read-only	The index of the port.
INT portRack	1.3.6.1.4.1.760.1.1.2.1.5.1.1	INTEGER	read-only	The index of the rack where the modem to which this port belongs is installed.
INT portType	1.3.6.1.4.1.760.1.1.2.1.5.1.4	INTEGER	read-only	This entry indicates the type of the port.
INT psignalModem	1.3.6.1.4.1.760.1.1.2.1.6.1.2	INTEGER	read-only	The index of the modem to which the port belongs that provides the signal.
INT psignalPort	1.3.6.1.4.1.760.1.1.2.1.6.1.3	INTEGER	read-only	The index of the port that provides the signal.
INT psignalRack	1.3.6.1.4.1.760.1.1.2.1.6.1.1	INTEGER	read-only	The index of the rack where the modem is installed to which the port belongs that provides the signal.
INT psignalStatus	1.3.6.1.4.1.760.1.1.2.1.6.1.5	INTEGER	read-only	This entry indicates the current status of the signal.
INT psignalTrap	1.3.6.1.4.1.760.1.1.2.1.6.1.6	INTEGER	read-write	This enables or disables traps. If Trap is enabled each transition of the signal status may cause a trap portSignalStatusGood/portSignalStatusBad.
INT psignalType	1.3.6.1.4.1.760.1.1.2.1.6.1.4	INTEGER	read-only	This entry indicates the signal type.
INT rackModems	1.3.6.1.4.1.760.1.1.2.1.2.1.5	INTEGER	read-only	This entry shows the number of modems currently installed in the rack.
INT rackModemSlots	1.3.6.1.4.1.760.1.1.2.1.2.1.4	INTEGER	read-only	This entry shows the number of slots for modem cards in the rack.
INT rackPowerSupplies	1.3.6.1.4.1.760.1.1.2.1.2.1.7	INTEGER	read-only	This entry shows the number of power supplies currently installed in the rack.
INT rackPowerSupplySlots	1.3.6.1.4.1.760.1.1.2.1.2.1.6	INTEGER	read-only	This entry shows the number of slots for power supplies in the rack.
INT rackRack	1.3.6.1.4.1.760.1.1.2.1.2.1.1	INTEGER	read-only	The index of this particular modem rack in the stack. The index of the rack which contains the agent should have the number 1.
INT rackType	1.3.6.1.4.1.760.1.1.2.1.2.1.2	INTEGER	read-only	This entry shows the type number of the rack.
INT rmdmInterfacePorts	1.3.6.1.4.1.760.1.1.2.1.9.3.1.8	INTEGER	read-only	This entry indicates the number of interface ports of the remote modem. An interface port connects an external device.
INT rmdmLinePorts	1.3.6.1.4.1.760.1.1.2.1.9.3.1.9	INTEGER	read-only	This entry indicates the number of line ports of the modem. A line port connects the local counterpart of the remote modem.
INT rmdmModem	1.3.6.1.4.1.760.1.1.2.1.9.3.1.2	INTEGER	read-only	The index of the modem that the remote modem is linked to.
INT rmdmRack	1.3.6.1.4.1.760.1.1.2.1.9.3.1.1	INTEGER	read-only	This entry indicates the index of the rack where the modem is installed that the remote modem is linked to.
INT rmdmRemoteAccessStatus	1.3.6.1.4.1.760.1.1.2.1.9.3.1.7	INTEGER	read-only	This entry shows the access status of the modem. The standard value depends on the device. Some modems are always accessible, others are not accessible or can be switched to both modes (see 'mdmForcedRemoteAccess' in the specific modem MIB).
INT rmdmSelfTest	1.3.6.1.4.1.760.1.1.2.1.9.3.1.5	INTEGER	read-write	This entry enables the execution of a selftest. Write requests with values other than 'start' or 'cancel' will be rejected. The result will be found in SelfTestResult.
INT rmdmSelfTestResult	1.3.6.1.4.1.760.1.1.2.1.9.3.1.6	INTEGER	read-only	This indicates the result status of the last modem-dependent self test. After start, the status may change to 'running' before the first error that occured displays. If no error was detected the status changes to 'ok'.
INT rportConnector	1.3.6.1.4.1.760.1.1.2.1.9.5.1.6	INTEGER	read-only	This entry indicates the connector type of the port.
INT rportInterfaceType	1.3.6.1.4.1.760.1.1.2.1.9.5.1.5	INTEGER	read-only	This entry indicates the type of interface of the port.
INT rportLoopMode	1.3.6.1.4.1.760.1.1.2.1.9.5.1.7	INTEGER	read-write	This entry indicates the loop mode of the port (remote, digital, line, off).
INT rportModem	1.3.6.1.4.1.760.1.1.2.1.9.5.1.2	INTEGER	read-only	The index of the local counterpart of the remote modem to which this port belongs.
INT rportPort	1.3.6.1.4.1.760.1.1.2.1.9.5.1.3	INTEGER	read-only	The index of the port.
INT rportRack	1.3.6.1.4.1.760.1.1.2.1.9.5.1.1	INTEGER	read-only	The index of the rack where the local counterpart of the remote modem is installed to which this port belongs.
INT rportType	1.3.6.1.4.1.760.1.1.2.1.9.5.1.4	INTEGER	read-only	This entry indicates the type of the port.
INT rpsignalModem	1.3.6.1.4.1.760.1.1.2.1.9.6.1.2	INTEGER	read-only	The index of the local counterpart of the remote modem.
INT rpsignalPort	1.3.6.1.4.1.760.1.1.2.1.9.6.1.3	INTEGER	read-only	The index of the port at the remote modem that provides the signal.
INT rpsignalRack	1.3.6.1.4.1.760.1.1.2.1.9.6.1.1	INTEGER	read-only	The index of the rack where the local counterpart of the remote modem is installed.
INT rpsignalStatus	1.3.6.1.4.1.760.1.1.2.1.9.6.1.5	INTEGER	read-only	This entry indicates the current status of the signal.
INT rpsignalType	1.3.6.1.4.1.760.1.1.2.1.9.6.1.4	INTEGER	read-only	This entry indicates the signal type.
INT rviFrontVer	1.3.6.1.4.1.760.1.1.2.1.9.4.1.7	INTEGER	read-only	For factory purposes only.
INT rviModem	1.3.6.1.4.1.760.1.1.2.1.9.4.1.2	INTEGER	read-only	The index of the modem that the remote modem is linked to.
INT rviRack	1.3.6.1.4.1.760.1.1.2.1.9.4.1.1	INTEGER	read-only	The index of the rack where the modem is installed that the remote modem is linked to.
INT rviType	1.3.6.1.4.1.760.1.1.2.1.9.4.1.3	INTEGER	read-only	This entry indicates the type of the remote modem.
INT viFrontVer	1.3.6.1.4.1.760.1.1.2.1.4.1.7	INTEGER	read-only	For factory purposes only.
INT viModem	1.3.6.1.4.1.760.1.1.2.1.4.1.2	INTEGER	read-only	The index of this particular modem in the rack. The value corresponds with the slot where the modem is inserted.
INT viRack	1.3.6.1.4.1.760.1.1.2.1.4.1.1	INTEGER	read-only	The index of the rack where the modem is installed.
INT viType	1.3.6.1.4.1.760.1.1.2.1.4.1.3	INTEGER	read-only	This entry indicates the type of the modem.
No type (104)
b_ac_x_5v_6a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.7
b_dc_24v_5v_su	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.10
b_dc_48v_5v_hc	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.9
b_dc_48v_5v_lc	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.8
backupPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.6
bertEntry	1.3.6.1.4.1.760.1.1.2.1.7.1		not-accessible	The index of thetable.
cms_intelligent_slave	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10003
cms_slave	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10002
cms_snmp_master	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10001
comp_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.1
controlSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.6
device_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.2
device_stack_15s	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.6
fAN1_FAN2_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.1
fAN1_off_FAN2_off	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.2
fAN1_off_FAN2_on	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.4
fAN1_on_FAN2_off	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.3
fAN1_on_FAN2_on	1.3.6.1.4.1.760.1.1.2.1.10.10000.7.5
fanonoff_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.7
hs_rack_10s_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.9
hs_rack_3s_1c_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.11
interfacePort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.2
linePort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.3
mdm_mgmt	1.3.6.1.4.1.760.1.1.2.1
mdm_oid	1.3.6.1.4.1.760.1.1.2.1.10.10000
mdmBERTTable	1.3.6.1.4.1.760.1.1.2.1.7		not-accessible	Table which contains information about all performable bit error rate tests.
mdmGroup	1.3.6.1.4.1.760.1.1.2.1.1
mdmMgmtIfGroup	1.3.6.1.4.1.760.1.1.2.1.20
mdmModemTable	1.3.6.1.4.1.760.1.1.2.1.3		not-accessible	Table which contains general information about the installed modems.
mdmPortSignalTable	1.3.6.1.4.1.760.1.1.2.1.6		not-accessible	Table which contains information about all port status signals.
mdmPortTable	1.3.6.1.4.1.760.1.1.2.1.5		not-accessible	Table which contains information about all ports.
mdmRackTable	1.3.6.1.4.1.760.1.1.2.1.2		not-accessible	Table which contains information about the installed racks.
mdmRemoteAccess	1.3.6.1.4.1.760.1.1.2.1.9
mdmSpecifics	1.3.6.1.4.1.760.1.1.2.1.10
mdmVerInfoTable	1.3.6.1.4.1.760.1.1.2.1.4		not-accessible	Table which contains information about the installed modems' versions.
mgmtAddr	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.4
mgmtSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.2
mibs	1.3.6.1.4.1.760.1
NTF modemAdded	1.3.6.1.4.1.760.1.1.2.1.0.3			This trap will be sent when a modem is added. The rack number and the index of the new modem is sent along with this trap.
modemAddr	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.3
modemEntry	1.3.6.1.4.1.760.1.1.2.1.3.1		not-accessible	The index of the table.
NTF modemRemoved	1.3.6.1.4.1.760.1.1.2.1.0.4			This trap will be sent when a modem in one of the slots is removed. The rack number and the index of the removed modem is sent along with this trap.
modemSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.1
otherModem	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.1
otherPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.1
outbandmgmtPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.5
p_ac_x_3v_20a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.11
p_ac_x_5v_20a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.2
p_ac_x_5v_30a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.3
p_dc_24v_5v_15a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.5
p_dc_48v_5v_18a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.4
p_dc_48v_5v_20a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.12
p_dc_48v_5v_30a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.6
p_dc_5v_3v_4a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.13
p_dc_5v_5v_5a	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.14
pandatel	1.3.6.1.4.1.760
port_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.4
NTF portBackupAvailable	1.3.6.1.4.1.760.1.1.2.1.0.11			This trap will be sent when a second link can be used as backup. The rack number, index of the modem, and port number is sent along with this trap.
NTF portBackupDisabled	1.3.6.1.4.1.760.1.1.2.1.0.10			This trap will be sent when a modem in one of the slots leaves a backup status. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
NTF portBackupEnabled	1.3.6.1.4.1.760.1.1.2.1.0.9			This trap will be sent when a modem in one of the slots enters a backup status. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
NTF portBackupNotAvailable	1.3.6.1.4.1.760.1.1.2.1.0.12			This trap will be sent when there is no second link available as backup. The rack number, index of the modem, and port number is sent along with this trap.
NTF portDataPortChanged	1.3.6.1.4.1.760.1.1.2.1.0.13			This trap will be sent when the line port used for data transmission is changed. The first port indicates the active data port, the second the inactive port. The rack number, index of the modem, and port number is sent along with this trap.
portEntry	1.3.6.1.4.1.760.1.1.2.1.5.1		not-accessible	The index of the table.
NTF portLoopDisabled	1.3.6.1.4.1.760.1.1.2.1.0.6			This trap will be sent when a modem in one of the slots disables a Loop. The rack number, index of the modem, and port number is sent along with this trap.
NTF portLoopEnabled	1.3.6.1.4.1.760.1.1.2.1.0.5			This trap will be sent when a modem in one of the slots enables a Loop. The rack number, index of the modem, and port number is sent along with this trap.
portSignalEntry	1.3.6.1.4.1.760.1.1.2.1.6.1		not-accessible	The index of the table.
NTF portSignalStatusBad	1.3.6.1.4.1.760.1.1.2.1.0.8			This trap will be sent when a status signal of a modem port enters the 'bad' status. The rack number, index of the modem, and port number is sent along with this trap.
NTF portSignalStatusGood	1.3.6.1.4.1.760.1.1.2.1.0.7			This will be sent when a status signal of a modem port enters the 'good' status. The rack number, index of the modem, and port number is sent along with this trap.
products	1.3.6.1.4.1.760.1.1
ps_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.5.1
pS1_on_PS2_off	1.3.6.1.4.1.760.1.1.2.1.10.10000.6.2
pS1_on_PS2_on	1.3.6.1.4.1.760.1.1.2.1.10.10000.6.3
pS1_PS2_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.6.1
psonoff_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.6
psupply_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.5
psupplySlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.10
rack_10s_2c_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.8
rack_10s_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.2
rack_10s_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.4
rack_12s_3hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.3
rack_1s_1c_1hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.12
rack_3s_1c_1hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.13
rack_6s_9s_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.5
rack_8s_2c_6hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.10
rack_8s_4hu	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.7
rack_other	1.3.6.1.4.1.760.1.1.2.1.10.10000.1.1
NTF rackAdded	1.3.6.1.4.1.760.1.1.2.1.0.1			This trap will be sent when a rack is added to the managed chassis. The rack index of the new rack is sent along with this trap.
rackEntry	1.3.6.1.4.1.760.1.1.2.1.2.1		not-accessible	The index of the table.
NTF rackRemoved	1.3.6.1.4.1.760.1.1.2.1.0.2			This trap will be sent when a rack is removed from the managed chassis. The rack index of the removed rack is sent along with this trap.
rc_control	1.3.6.1.4.1.760.1.1.2.1.10.10000.2.10004
remModemTable	1.3.6.1.4.1.760.1.1.2.1.9.3		not-accessible	Table which contains general information about all counterparts of the installed modems.
remPortEntry	1.3.6.1.4.1.760.1.1.2.1.9.5.1		not-accessible	The index of the table.
remPortSignalEntry	1.3.6.1.4.1.760.1.1.2.1.9.6.1		not-accessible	The index of the table.
remPortSignalTable	1.3.6.1.4.1.760.1.1.2.1.9.6		not-accessible	Table which contains information about all port status signals.
remPortTable	1.3.6.1.4.1.760.1.1.2.1.9.5		not-accessible	Table which contains information about all ports of the remote modem.
remVerInfoEntry	1.3.6.1.4.1.760.1.1.2.1.9.4.1		not-accessible	The index of the table.
remVerInfoTable	1.3.6.1.4.1.760.1.1.2.1.9.4		not-accessible	Table which contains information about the remote modems' versions.
rmodemEntry	1.3.6.1.4.1.760.1.1.2.1.9.3.1		not-accessible	The index of the table.
rs485Port	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.7
slot_id	1.3.6.1.4.1.760.1.1.2.1.10.10000.3
verInfoEntry	1.3.6.1.4.1.760.1.1.2.1.4.1		not-accessible	The index of the table.
vt100mgmtPort	1.3.6.1.4.1.760.1.1.2.1.10.10000.4.4
wan_products	1.3.6.1.4.1.760.1.1.2
wdmSlot	1.3.6.1.4.1.760.1.1.2.1.10.10000.3.5

RFC description

Vendor-private MIB for Pandatel modem and digital communication devices management.

Start monitoring Pandatel AG modem chassis/rack (base modem family MIB) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PANDATEL-MODEM-MIB

This MIB depends on

Related MIBs

What Is PANDATEL-MODEM-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

RFC description