PACKETFLUX-STANDBYPOWER

All MIBs › PACKETFLUX-STANDBYPOWER

Organization: PacketFlux Technologies

Last Updated: 2013-06-04

Category: UPS/Power

Description: Monitors standby power system status, battery state, and alarm conditions on PacketFlux Technologies devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is PACKETFLUX-STANDBYPOWER?

PACKETFLUX-STANDBYPOWER is a PacketFlux Technologies proprietary MIB (built on PACKETFLUX-SMI) for the PacketFlux Standby Power Controller, managing automatic generator/transfer-switch failover at remote broadcast/telecom sites. Its objects cover power-controller/transfer-switch/standby-power state, AC1/AC2 voltage/frequency, meter 1/2 voltage, PWR 1/2 voltage, shunt voltage, temperature, recent/total unsuccessful-start and stall counts, start/transfer counts, and current/total time on primary and standby power (plus current standby runtime). As a status/performance MIB it lets an administrator confirm generator health and watch failover history on a PacketFlux Standby Power Controller. It is deployed on PacketFlux Technologies Standby Power Controller equipment. Engineers can download the PACKETFLUX-STANDBYPOWER file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in PACKETFLUX-STANDBYPOWER. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

PacketFlux Technologies Standby Power Controller equipment

Monitoring Examples

An administrator checks totalunsuccessfulstarts and standbypowerstate to confirm generator reliability and current failover state on a PacketFlux Standby Power Controller.

What Can Be Monitored

generator/transfer-switch health and failover history

Imported Objects

From PACKETFLUX-SMI

packetfluxMgmt

OBJECT-IDENTITY

From SNMPv2-CONF

OBJECT-GROUP

From SNMPv2-SMI

Gauge32
Integer32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

TruthValue

How to Use in IPNetwork Monitor

Example using ac1voltage OID:

Select a PacketFlux Technologies Standby Power Controller as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type ac1voltage into the Find box to locate it in the OID tree, then select it and click OK. The voltage of the AC input AC1 in 1/10ths of a volt. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Gauge32-type OID, Value bounds is the most useful condition here — trigger an alert if the value drifts significantly from its normal baseline, since an unexpected change often points to a real underlying issue. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
G32 ac1frequency	1.3.6.1.4.1.32050.2.2.5	Gauge32	read-only	The frequency of the AC input AC1 in 1/100ths of a Hertz.
G32 ac1voltageEx	1.3.6.1.4.1.32050.2.2.4	Gauge32	read-only	The voltage of the AC input AC1 in 1/10ths of a volt.
G32 ac2frequency	1.3.6.1.4.1.32050.2.2.7	Gauge32	read-only	The frequency of the AC input AC2 in 1/100ths of a Hertz.
G32 ac2voltage	1.3.6.1.4.1.32050.2.2.6	Gauge32	read-only	The voltage of the AC input AC2 in 1/10ths of a volt.
TIK currentstandbyruntime	1.3.6.1.4.1.32050.2.2.24	TimeTicks	read-write	The amount of time the standby power source has been running during it's current run. This timer resets to zero when the standby power source shuts down. This timer can be reset via the web interface or by writing 0 to this object.
TIK currenttimeonprimary	1.3.6.1.4.1.32050.2.2.20	TimeTicks	read-write	The amount of time the transfer switch has been in the primary state (position) since the most recent transfer to that state. This timer resets to zero when the transfer switch leaves the primary state (position). This timer can be reset via the web interface or by writing 0 to this object.
TIK currenttimeonstandby	1.3.6.1.4.1.32050.2.2.22	TimeTicks	read-write	The amount of time the transfer switch has been in the standby state (position) since the most recent transfer to that state. This timer resets to zero when the transfer switch leaves the primary state (position). This timer can be reset via the web interface or by writing 0 to this object.
T/F enabled	1.3.6.1.4.1.32050.2.2.35	TruthValue	read-only	True(1) if the enable input is closed (shorted/on). False(2) if it is open.
TIK laststandbyfailure	1.3.6.1.4.1.32050.2.2.29	TimeTicks	read-write	The amount of time since the stall or failure while running of the standby power source . This timer resets and starts timing upon a stall/failure of the power source. This timer can be reset via the web interface or by writing 0 to this object.
TIK laststandbygracefulstop	1.3.6.1.4.1.32050.2.2.27	TimeTicks	read-write	The amount of time since standby power source was gracefully shutdown. This timer resets and starts timing upon graceful shutdown of the standby power source. This timer can be reset via the web interface or by writing 0 to this object.
TIK laststandbyrun	1.3.6.1.4.1.32050.2.2.26	TimeTicks	read-write	The amount of time since the standby power source ran last. This timer resets upon start of the standby power source and starts timing upon shutdown of the standby power source. This timer can be reset via the web interface or by writing 0 to this object.
TIK laststandbyunsuccessfulstart	1.3.6.1.4.1.32050.2.2.28	TimeTicks	read-write	The amount of time since the last failed start of the standby power source . This timer resets and starts timing upon a unsuccessful start of the power source. This timer can be reset via the web interface or by writing 0 to this object.
G32 mtr1voltage	1.3.6.1.4.1.32050.2.2.8	Gauge32	read-only	The voltage of the DC input Mtr1 in 1/10ths of a volt.
G32 mtr2voltage	1.3.6.1.4.1.32050.2.2.9	Gauge32	read-only	The voltage of the DC input Mtr2 in 1/10ths of a volt.
I32 numberofstarts	1.3.6.1.4.1.32050.2.2.18	Integer32	read-write	The number of times the secondary power source has started. This counter increments when the standby sequence reaches the running state. This counter can be reset via the web interface or by writing 0 to this object.
I32 numberoftransfers	1.3.6.1.4.1.32050.2.2.19	Integer32	read-write	The number of times the power has transfered from primary to standby, or back. A complete transfer cycle from primary to standby and back to primary will increment this counter twice. This counter can be reset via the web interface or by writing 0 to this object.
packetfluxStandbypowerAllObjects	1.3.6.1.4.1.32050.2.2.256.1.1			This automatically created object group contains all those objects that do not belong to any other OBJECT-GROUP
INT powercontrollerstate	1.3.6.1.4.1.32050.2.2.1	INTEGER	read-only	The status of the standby power controller.
G32 pwr1voltage	1.3.6.1.4.1.32050.2.2.10	Gauge32	read-only	The voltage of the DC input Pwr3 in 1/10ths of a volt.
G32 pwr2voltage	1.3.6.1.4.1.32050.2.2.11	Gauge32	read-only	The voltage of the DC input Pwr2 in 1/10ths of a volt.
I32 recentstalls	1.3.6.1.4.1.32050.2.2.16	Integer32	read-write	The number of times the standby power source has stalled. This counter resets upon a clean shutdown. It can also be reset via the web interface or by writing 0 to this object.
I32 recentunsuccessfulstarts	1.3.6.1.4.1.32050.2.2.14	Integer32	read-write	The number of times the standby power source was not successfully started. This counter resets upon a successful start. It can also be reset via the web interface or by writing 0 to this object.
T/F relay1on	1.3.6.1.4.1.32050.2.2.36	TruthValue	read-only	True(1) if the Relay 1 ouput is on (C and NO connected). False(2) if it is off (C and NC connected).
T/F relay2on	1.3.6.1.4.1.32050.2.2.37	TruthValue	read-only	True(1) if the Relay 2 ouput is on (C and NO connected). False(2) if it is off (C and NC connected).
T/F relay3on	1.3.6.1.4.1.32050.2.2.38	TruthValue	read-only	True(1) if the Relay 3 ouput is on (C and NO connected). False(2) if it is off (C and NC connected).
T/F relay4on	1.3.6.1.4.1.32050.2.2.39	TruthValue	read-only	True(1) if the Relay 4 ouput is on (C and NO connected). False(2) if it is off (C and NC connected).
T/F relay5on	1.3.6.1.4.1.32050.2.2.40	TruthValue	read-only	True(1) if the Relay 5 output is on (C and NO connected). False(2) if it is off (C and NC connected).
T/F relay6on	1.3.6.1.4.1.32050.2.2.41	TruthValue	read-only	True(1) if the Relay 6 output is on (C and NO connected). False(2) if it is off (C and NC connected).
T/F relay7on	1.3.6.1.4.1.32050.2.2.42	TruthValue	read-only	True(1) if the Relay 7 output is on (C and NO connected). False(2) if it is off (C and NC connected).
T/F ruleexercisestandby	1.3.6.1.4.1.32050.2.2.47	TruthValue	read-only	True(1) if the exercise standby without transfer rule is true. False(2) if it is not.
T/F rulereturnprimary	1.3.6.1.4.1.32050.2.2.44	TruthValue	read-only	True(1) if the return to primary rule is true. False(2) if it is not.
T/F rulestandbygood	1.3.6.1.4.1.32050.2.2.45	TruthValue	read-only	True(1) if the standby power good rule is true. False(2) if it is not.
T/F rulestopstandby	1.3.6.1.4.1.32050.2.2.46	TruthValue	read-only	True(1) if the stop standby and consider it failed rule is true. False(2) if it is not.
T/F ruleswitchstandby	1.3.6.1.4.1.32050.2.2.43	TruthValue	read-only	True(1) if the switch to standby rule is true. False(2) if it is not.
I32 shuntvoltage	1.3.6.1.4.1.32050.2.2.12	Integer32	read-only	The voltage of the DC input Shunt in 1/10ths of a millivolt. Can be negative.
standbypower	1.3.6.1.4.1.32050.2.2			MIB for the PacketFlux Standby Power Controller
standbypowerConformance	1.3.6.1.4.1.32050.2.2.256
standbypowerGroups	1.3.6.1.4.1.32050.2.2.256.1
INT standbypowerstate	1.3.6.1.4.1.32050.2.2.3	INTEGER	read-only	The current state in the standby power sequence.
T/F switch1closed	1.3.6.1.4.1.32050.2.2.30	TruthValue	read-only	True(1) if the Switch 1 input is closed (shorted/on). False(2) if it is open.
T/F switch2closed	1.3.6.1.4.1.32050.2.2.31	TruthValue	read-only	True(1) if the Switch 2 input is closed (shorted/on). False(2) if it is open.
T/F switch3closed	1.3.6.1.4.1.32050.2.2.32	TruthValue	read-only	True(1) if the Switch 3 input is closed (shorted/on). False(2) if it is open.
T/F switch4closed	1.3.6.1.4.1.32050.2.2.33	TruthValue	read-only	True(1) if the Switch 4 input is closed (shorted/on). False(2) if it is open.
T/F switch5closed	1.3.6.1.4.1.32050.2.2.34	TruthValue	read-only	True(1) if the Switch 5 input is closed (shorted/on). False(2) if it is open.
G32 temperature	1.3.6.1.4.1.32050.2.2.13	Gauge32	read-only	The temperature of the onboard temperature sensor in 1/10ths of a degree centigrade.
I32 totalstalls	1.3.6.1.4.1.32050.2.2.17	Integer32	read-write	The number of times the standby power source has stalled. This counter DOES NOT reset upon a clean shutdown. It can be reset via the web interface or by writing 0 to this object.
TIK totalstandbyruntime	1.3.6.1.4.1.32050.2.2.25	TimeTicks	read-write	The amount of time the standby power source has been running since power on or the last reset of this counter. This timer does not automatically reset. This timer can be reset via the web interface or by writing 0 to this object.
TIK totaltimeonprimary	1.3.6.1.4.1.32050.2.2.21	TimeTicks	read-write	The amount of time the transfer switch has been in the primary state (position) since power on or the last reset of this counter. This timer does not automatically reset. This timer can be reset via the web interface or by writing 0 to this object.
TIK totaltimeonstandby	1.3.6.1.4.1.32050.2.2.23	TimeTicks	read-write	The amount of time the transfer switch has been in the standby state (position) since power on or the last reset of this counter. This timer does not automatically reset. This timer can be reset via the web interface or by writing 0 to this object.
I32 totalunsuccessfulstarts	1.3.6.1.4.1.32050.2.2.15	Integer32	read-write	The number of times the standby power source was not successfully started. This counter DOES NOT reset upon a successful start. It can be reset via the web interface or by writing 0 to this object.
INT transferswitchstate	1.3.6.1.4.1.32050.2.2.2	INTEGER	read-only	The current state in the transfer sequence.
T/F webcontrol1	1.3.6.1.4.1.32050.2.2.48	TruthValue	read-write	True(1) if the webcontrol 1 virtual toggle switch is in the on position. False(2) if it is not. This value can be written to affect the position of the toggle switch.
T/F webcontrol2	1.3.6.1.4.1.32050.2.2.49	TruthValue	read-write	True(1) if the webcontrol 2 virtual toggle switch is in the on position. False(2) if it is not. This value can be written to affect the position of the toggle switch.
T/F webcontrol3	1.3.6.1.4.1.32050.2.2.50	TruthValue	read-write	True(1) if the webcontrol 3 virtual toggle switch is in the on position. False(2) if it is not. This value can be written to affect the position of the toggle switch.
T/F webcontrol4	1.3.6.1.4.1.32050.2.2.51	TruthValue	read-write	True(1) if the webcontrol 4 virtual toggle switch is in the on position. False(2) if it is not. This value can be written to affect the position of the toggle switch.
T/F webcontrol5	1.3.6.1.4.1.32050.2.2.52	TruthValue	read-write	True(1) if the webcontrol 5 virtual toggle switch is in the on position. False(2) if it is not. This value can be written to affect the position of the toggle switch.
T/F webcontrol6	1.3.6.1.4.1.32050.2.2.53	TruthValue	read-write	True(1) if the webcontrol 6 virtual toggle switch is in the on position. False(2) if it is not. This value can be written to affect the position of the toggle switch.
T/F webcontrol7	1.3.6.1.4.1.32050.2.2.54	TruthValue	read-write	True(1) if the webcontrol 7 virtual toggle switch is in the on position. False(2) if it is not. This value can be written to affect the position of the toggle switch.
T/F webcontrol8	1.3.6.1.4.1.32050.2.2.55	TruthValue	read-write	True(1) if the webcontrol 8 virtual toggle switch is in the on position. False(2) if it is not. This value can be written to affect the position of the toggle switch.

RFC description

Monitors standby power controller status and transfer switch states for PacketFlux power management systems.

Start monitoring PacketFlux Technologies Standby Power Controller with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download PACKETFLUX-STANDBYPOWER