Nortel-Magellan-Passport-VnetEtsiQsigMIB

All MIBs › Nortel-Magellan-Passport-VnetEtsiQsigMIB

Category: Nortel Magellan Passport

Description: Defines SNMP objects for ETSI QSIG virtual network signaling on Nortel Magellan Passport switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Nortel-Magellan-Passport-VnetEtsiQsigMIB?

This MIB is a Nortel-specific module for the Magellan Passport multiservice switching platform, defining SNMP management objects for the ETSI QSIG virtual network signaling protocol used on private branch exchange (PBX) trunk interfaces. It exposes configuration and provisioning data for signaling channels, including row-status-controlled component tables, storage type, and Layer 2 data-link parameters such as the T200, T23 and N200 timers that govern QSIG/Q.921 link establishment and retransmission behavior. Because the objects are almost entirely provisioning/configuration in nature (row status, component names, timer values) rather than live performance counters, monitoring value here centers on verifying that a signaling channel's administrative and link-layer configuration is correctly provisioned and stable (row status active/notInService) rather than tracking hardware health metrics like temperature or CPU. It builds on Nortel's proprietary Passport component-instance model (component name/index/row-status pattern used across all MsCarrier/Magellan Passport MIBs) and implicitly depends on the ITU-T Q.921/QSIG signaling stack conventions. It is typically deployed in carrier or enterprise voice networks using Nortel Magellan Passport switches to interconnect PBXs over ETSI QSIG trunks for private numbering plan and supplementary-service signaling. Engineers can download the Nortel-Magellan-Passport-VnetEtsiQsigMIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Nortel-Magellan-Passport-VnetEtsiQsigMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nortel Magellan Passport switch
PBX/voice trunk signaling interface

Monitoring Examples

An administrator would poll sigChanEQsigRowStatusTable/sigChanEQsigRowStatusEntry to confirm a QSIG signaling channel component is in the "active" row status, and inspect sigChanEQsigL2Table entries for the configured sigChanEQsigT200, sigChanEQsigT23 and sigChanEQsigN200 timer values against the far-end PBX's QSIG configuration. A mismatch or unexpected change in sigChanEQsigStorageType or component index could indicate a misconfigured or newly provisioned channel that is failing to establish Layer 2 link with the peer switch. Because this MIB has no runtime performance counters, anomalies show up as row-status transitions rather than counter thresholds.

What Can Be Monitored

QSIG signaling channel row status
Layer 2 link timers (T200, T23, N200)
component storage type
signaling channel provisioning index

Imported Objects

From Nortel-Magellan-Passport-StandardTextualConventionsMIB

DisplayString
RowStatus
StorageType
Unsigned32

From Nortel-Magellan-Passport-TextualConventionsMIB

Link
NonReplicated

From Nortel-Magellan-Passport-UsefulDefinitionsMIB

passportMIBs

OBJECT-IDENTITY

From Nortel-Magellan-Passport-VoiceNetworkingMIB

sigChan	OBJECT-IDENTITY
sigChanIndex	OBJECT-TYPE

From RFC-1212

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
sigChanEQsig	1.3.6.1.4.1.562.2.4.1.115.2
sigChanEQsigRowStatusTable	1.3.6.1.4.1.562.2.4.1.115.2.1		not-accessible	This entry controls the addition and deletion of sigChanEQsig components.
sigChanEQsigRowStatusEntry	1.3.6.1.4.1.562.2.4.1.115.2.1.1		not-accessible	A single entry in the table represents a single sigChanEQsig component.
ROW sigChanEQsigRowStatus	1.3.6.1.4.1.562.2.4.1.115.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of sigChanEQsig components. These components can be added and deleted.
STR sigChanEQsigComponentName	1.3.6.1.4.1.562.2.4.1.115.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO sigChanEQsigStorageType	1.3.6.1.4.1.562.2.4.1.115.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the sigChanEQsig tables.
NON sigChanEQsigIndex	1.3.6.1.4.1.562.2.4.1.115.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the sigChanEQsig tables.
sigChanEQsigFramer	1.3.6.1.4.1.562.2.4.1.115.2.2
sigChanEQsigFramerRowStatusTable	1.3.6.1.4.1.562.2.4.1.115.2.2.1		not-accessible	This entry controls the addition and deletion of sigChanEQsigFramer components.
sigChanEQsigFramerRowStatusEntry	1.3.6.1.4.1.562.2.4.1.115.2.2.1.1		not-accessible	A single entry in the table represents a single sigChanEQsigFramer component.
ROW sigChanEQsigFramerRowStatus	1.3.6.1.4.1.562.2.4.1.115.2.2.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of sigChanEQsigFramer components. These components cannot be added nor deleted.
STR sigChanEQsigFramerComponentName	1.3.6.1.4.1.562.2.4.1.115.2.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO sigChanEQsigFramerStorageType	1.3.6.1.4.1.562.2.4.1.115.2.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the sigChanEQsigFramer tables.
NON sigChanEQsigFramerIndex	1.3.6.1.4.1.562.2.4.1.115.2.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the sigChanEQsigFramer tables.
sigChanEQsigFramerProvTable	1.3.6.1.4.1.562.2.4.1.115.2.2.10		not-accessible	This group contains the base provisioning data for the Framer component. Application or hardware interface specific provisioning data is contained in other provisionable Framer groups.
sigChanEQsigFramerProvEntry	1.3.6.1.4.1.562.2.4.1.115.2.2.10.1		not-accessible	An entry in the sigChanEQsigFramerProvTable.
LIN sigChanEQsigFramerInterfaceName	1.3.6.1.4.1.562.2.4.1.115.2.2.10.1.1	Link	read-write	This attribute contains a hardware component name. The attribute associates the application with a specific link. This defines the module processor on which Framer's parent component (as well as Framer itself) will run.
sigChanEQsigFramerStateTable	1.3.6.1.4.1.562.2.4.1.115.2.2.12		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
sigChanEQsigFramerStateEntry	1.3.6.1.4.1.562.2.4.1.115.2.2.12.1		not-accessible	An entry in the sigChanEQsigFramerStateTable.
INT sigChanEQsigFramerAdminState	1.3.6.1.4.1.562.2.4.1.115.2.2.12.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT sigChanEQsigFramerOperationalState	1.3.6.1.4.1.562.2.4.1.115.2.2.12.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT sigChanEQsigFramerUsageState	1.3.6.1.4.1.562.2.4.1.115.2.2.12.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
sigChanEQsigFramerStatsTable	1.3.6.1.4.1.562.2.4.1.115.2.2.13		not-accessible	This group contains the operational statistics data for a Framer component.
sigChanEQsigFramerStatsEntry	1.3.6.1.4.1.562.2.4.1.115.2.2.13.1		not-accessible	An entry in the sigChanEQsigFramerStatsTable.
U32 sigChanEQsigFramerFrmToIf	1.3.6.1.4.1.562.2.4.1.115.2.2.13.1.1	Unsigned32	read-only	This attribute counts the number of frames transmitted to the link interface by Framer. This count wraps to zero after reaching its maximum value.
U32 sigChanEQsigFramerFrmFromIf	1.3.6.1.4.1.562.2.4.1.115.2.2.13.1.2	Unsigned32	read-only	This attribute counts the number of frames received from the link interface by Framer. This count wraps to zero after reaching its maximum value.
U32 sigChanEQsigFramerOctetFromIf	1.3.6.1.4.1.562.2.4.1.115.2.2.13.1.3	Unsigned32	read-only	The number of bytes received from the link interface by Framer.
U32 sigChanEQsigFramerAborts	1.3.6.1.4.1.562.2.4.1.115.2.2.13.1.4	Unsigned32	read-only	This attribute counts the total number of aborts received. This count wraps to zero after reaching its maximum value.
U32 sigChanEQsigFramerCrcErrors	1.3.6.1.4.1.562.2.4.1.115.2.2.13.1.5	Unsigned32	read-only	This attribute counts the total number of frames with CRC errors. This count wraps to zero after reaching its maximum value.
U32 sigChanEQsigFramerLrcErrors	1.3.6.1.4.1.562.2.4.1.115.2.2.13.1.6	Unsigned32	read-only	This attribute counts the total number of frames with LRC errors. This count wraps to zero after reaching its maximum value.
U32 sigChanEQsigFramerNonOctetErrors	1.3.6.1.4.1.562.2.4.1.115.2.2.13.1.7	Unsigned32	read-only	This attribute counts the total number of frames that were non octet aligned. This count wraps to zero after reaching its maximum value.
U32 sigChanEQsigFramerOverruns	1.3.6.1.4.1.562.2.4.1.115.2.2.13.1.8	Unsigned32	read-only	This attribute counts the total number of frames received from the link for which overruns occurred. This count wraps to zero after reaching its maximum value.
U32 sigChanEQsigFramerUnderruns	1.3.6.1.4.1.562.2.4.1.115.2.2.13.1.9	Unsigned32	read-only	This attribute counts the total number of frames transmitted to the link for which underruns occurred. This count wraps to zero after reaching its maximum value.
U32 sigChanEQsigFramerLargeFrmErrors	1.3.6.1.4.1.562.2.4.1.115.2.2.13.1.10	Unsigned32	read-only	This attribute counts the total number of frames received which were too large (longer than 500 bytes). This count wraps to zero after reaching its maximum value.
sigChanEQsigL2Table	1.3.6.1.4.1.562.2.4.1.115.2.11		not-accessible	This group specifies the provisionable layer 2 attributes of the Q.931 ITU-T protocol.
sigChanEQsigL2Entry	1.3.6.1.4.1.562.2.4.1.115.2.11.1		not-accessible	An entry in the sigChanEQsigL2Table.
U32 sigChanEQsigT23	1.3.6.1.4.1.562.2.4.1.115.2.11.1.1	Unsigned32	read-write	This attribute specifies the layer 2 enable request timer.
U32 sigChanEQsigT200	1.3.6.1.4.1.562.2.4.1.115.2.11.1.2	Unsigned32	read-write	This attribute specifies the maximum time between a layer 2 frame and its acknowledgment.
U32 sigChanEQsigN200	1.3.6.1.4.1.562.2.4.1.115.2.11.1.3	Unsigned32	read-write	This attribute specifies the maximum number of re-transmissions of a layer 2 frame.
U32 sigChanEQsigT203	1.3.6.1.4.1.562.2.4.1.115.2.11.1.4	Unsigned32	read-write	This attribute specifies the maximum time for which layer 2 frames may be absent. Expiry triggers a check on whether the far end is alive.
U32 sigChanEQsigCircuitSwitchedK	1.3.6.1.4.1.562.2.4.1.115.2.11.1.6	Unsigned32	read-write	This attribute specifies the maximum number of sequentially numbered I frames (that is, window size (k)) that may be unacknowledged at any given time for a SAP supporting primary rate (64kbit/sec) signalling.
sigChanEQsigL3Table	1.3.6.1.4.1.562.2.4.1.115.2.12		not-accessible	This group represents the provisionable Layer 3 timer attributes of the ETSI Qsig protocol.
sigChanEQsigL3Entry	1.3.6.1.4.1.562.2.4.1.115.2.12.1		not-accessible	An entry in the sigChanEQsigL3Table.
U32 sigChanEQsigT309	1.3.6.1.4.1.562.2.4.1.115.2.12.1.3	Unsigned32	read-write	This attribute specifies the data link failure timer; used to ride out temporary failures.
U32 sigChanEQsigT310	1.3.6.1.4.1.562.2.4.1.115.2.12.1.4	Unsigned32	read-write	This attribute specifies the call proceeding state timer.
sigChanEQsigProvTable	1.3.6.1.4.1.562.2.4.1.115.2.13		not-accessible	This group defines the general options of the D-channel signalling link.
sigChanEQsigProvEntry	1.3.6.1.4.1.562.2.4.1.115.2.13.1		not-accessible	An entry in the sigChanEQsigProvTable.
INT sigChanEQsigSide	1.3.6.1.4.1.562.2.4.1.115.2.13.1.1	INTEGER	read-write	This attribute specifies whether the interface is the network or user side of the connection. The parameter applies to both the layer 2 and layer 3 of the interface. If this attribute is set to network, then the interface is master during channel negotiation. If this attribute is set to user, then the interface is slave during channel negotiation.
U32 sigChanEQsigMaxNonCallConcurrent	1.3.6.1.4.1.562.2.4.1.115.2.13.1.2	Unsigned32	read-write	This attribute specifies the maximum number of simultaneous active non-call messages that are allowed.
INT sigChanEQsigOverlapSendingEnabled	1.3.6.1.4.1.562.2.4.1.115.2.13.1.3	INTEGER	read-write	This attribute specifies whether overlap sending to the PBX is enabled.
INT sigChanEQsigOverlapReceivingEnabled	1.3.6.1.4.1.562.2.4.1.115.2.13.1.4	INTEGER	read-write	This attribute specifies whether overlap receiving from the PBX is enabled.
sigChanEQsigStateTable	1.3.6.1.4.1.562.2.4.1.115.2.14		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
sigChanEQsigStateEntry	1.3.6.1.4.1.562.2.4.1.115.2.14.1		not-accessible	An entry in the sigChanEQsigStateTable.
INT sigChanEQsigAdminState	1.3.6.1.4.1.562.2.4.1.115.2.14.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT sigChanEQsigOperationalState	1.3.6.1.4.1.562.2.4.1.115.2.14.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT sigChanEQsigUsageState	1.3.6.1.4.1.562.2.4.1.115.2.14.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
sigChanEQsigStatsTable	1.3.6.1.4.1.562.2.4.1.115.2.15		not-accessible	This group provides the operational components for the EtsiQsig component.
sigChanEQsigStatsEntry	1.3.6.1.4.1.562.2.4.1.115.2.15.1		not-accessible	An entry in the sigChanEQsigStatsTable.
U32 sigChanEQsigTotalCallsToIf	1.3.6.1.4.1.562.2.4.1.115.2.15.1.2	Unsigned32	read-only	This attribute counts the total number of calls that have been made to the interface. The value wraps when it reaches its maximum.
U32 sigChanEQsigTotalCallsFromIf	1.3.6.1.4.1.562.2.4.1.115.2.15.1.3	Unsigned32	read-only	This attribute counts the total number of calls from the interface. The value wraps when it reaches its maximum.
U32 sigChanEQsigNonCallAssocSessionsToIf	1.3.6.1.4.1.562.2.4.1.115.2.15.1.4	Unsigned32	read-only	This attribute counts the total number of non-call associated sessions to the interface. The value wraps when it reaches its maximum.
U32 sigChanEQsigNonCallAssocSessionsFromIf	1.3.6.1.4.1.562.2.4.1.115.2.15.1.5	Unsigned32	read-only	This attribute counts the total number of non-call associated sessions from the interface. The value wraps when it reaches its maximum.
sigChanEQsigOperTable	1.3.6.1.4.1.562.2.4.1.115.2.16		not-accessible	This group provides the operational attributes for the EtsiQsig protocol.
sigChanEQsigOperEntry	1.3.6.1.4.1.562.2.4.1.115.2.16.1		not-accessible	An entry in the sigChanEQsigOperTable.
U32 sigChanEQsigActiveChannels	1.3.6.1.4.1.562.2.4.1.115.2.16.1.1	Unsigned32	read-only	This attribute indicates the number of currently active channels. This includes data and voice channels.
U32 sigChanEQsigActiveVoiceChannels	1.3.6.1.4.1.562.2.4.1.115.2.16.1.2	Unsigned32	read-only	This attribute indicates the number of channels that are currently carrying voice.
U32 sigChanEQsigActiveDataChannels	1.3.6.1.4.1.562.2.4.1.115.2.16.1.3	Unsigned32	read-only	This attribute indicates the number of channels that are currently carrying data. This does not include modem data.
U32 sigChanEQsigPeakActiveChannels	1.3.6.1.4.1.562.2.4.1.115.2.16.1.4	Unsigned32	read-only	This attribute indicates the maximum number of channels that have been active on this signalling channel during the last polling period.
U32 sigChanEQsigPeakActiveVoiceChannels	1.3.6.1.4.1.562.2.4.1.115.2.16.1.5	Unsigned32	read-only	This attribute indicates the maximum number of voice channels that have been active on this signalling channel during the last polling period.
U32 sigChanEQsigPeakActiveDataChannels	1.3.6.1.4.1.562.2.4.1.115.2.16.1.6	Unsigned32	read-only	This attribute indicates the maximum number of data channels that have been active on this signalling channel during the last polling period.
INT sigChanEQsigDChanStatus	1.3.6.1.4.1.562.2.4.1.115.2.16.1.7	INTEGER	read-only	This attribute indicates the state of the D-channel. outOfService means that there is no layer 2 or layer 3 connectivity to the PBX. establishing means that the signalling channel is attempting to stage the layer 2. established means that the layer 2 is enabled. If the signalling channel stays in the established state, then it is waiting for a restart from the PBX. enabling means that the resources for processing calls are being initialized. If the signalling channel stays in the enabling state then it is waiting for a restart acknowledgement from the PBX. inService means that the resources for processing calls are available. restarting means that the resources for call processing are being rei-initialized.
sigChanEQsigToolsTable	1.3.6.1.4.1.562.2.4.1.115.2.17		not-accessible	This contains a series of operational attributes which turn on and off several kinds of tracing.
sigChanEQsigToolsEntry	1.3.6.1.4.1.562.2.4.1.115.2.17.1		not-accessible	An entry in the sigChanEQsigToolsTable.
OCT sigChanEQsigTracing	1.3.6.1.4.1.562.2.4.1.115.2.17.1.1	OCTET STRING	read-write	This attribute defines which types of tracing are active for this signalling channel. The tracing messages are sent to the debug stream. To see the messages the agentQueue attribute in Col/debug must be greater than 0 and a Telnet NMIS session must list the debug stream in in its data streams (ex. set nmis telnet session/1 dataStreams debug). Different types of tracing can be enabled simultaneously. Note that tracing consumes additional CPU resources and will slow down call processing on a heavily loaded card. If there is message block exhaustion tracing will be suspended for a period and then automatically reenabled. An alarm is generated on tracing suspension and resumption. This mechanism protects the function processor against excessive numbers of tracing messages. Types of tracing include: protocolErrors - get details of any protocol errors which are occuring. Protocol errors are also reported in summary form as alarms. q931Summary - Summary of the Q.931 messages on the signalling link, including certain call details (calling number, called number, release codes). q931Hex - Q.931 messages displayed in hex format. Useful to determine protocol compliance in case of errors reported on local or remote ends. q931Symbolic - Q.931 messages parsed to give maximum detail. Useful for understanding content of messages flowing on the link. portHex - Messages in hex format being sent and received on the link. Description of bits: protocolErrors(0) q931Summary(1) q931Hex(2) q931Symbolic(3) portHex(4)
sigChanEQsigEQsigSpecificProvTable	1.3.6.1.4.1.562.2.4.1.115.2.18		not-accessible	This group provides EtsiQsig protocol specific provisioning.
sigChanEQsigEQsigSpecificProvEntry	1.3.6.1.4.1.562.2.4.1.115.2.18.1		not-accessible	An entry in the sigChanEQsigEQsigSpecificProvTable.
INT sigChanEQsigMsgSegmentation	1.3.6.1.4.1.562.2.4.1.115.2.18.1.1	INTEGER	read-write	This attribute allows users to enable/disable the EtsiQsig message segmentation service.
INT sigChanEQsigE1ChannelNumbers	1.3.6.1.4.1.562.2.4.1.115.2.18.1.2	INTEGER	read-write	This attribute is applicable to E1 interfaces only. It specifies the mapping scheme between channel numbers (identified in Layer 3 messages) and timeslot numbers on the E1 link. When the attribute value is skip16, channel numbers map directly to actual E1 timeslots; therefore only channel numbers 1 - 15 and 17 - 31 are expected. When the value is contiguous, channel numbers from 1 - 30 are expected, and the following mapping is used: channels 1 - 15 are mapped to timeslots 1 - 15, and channels 16 - 30 are mapped to timeslots 17 - 31. On T1 interfaces, channel numbers are always expected in the range 1 - 23.
sigChanEQsigEQsigSpecificOpTable	1.3.6.1.4.1.562.2.4.1.115.2.19		not-accessible	This group provides specific operational attributes for the Etsi Qsig protocol.
sigChanEQsigEQsigSpecificOpEntry	1.3.6.1.4.1.562.2.4.1.115.2.19.1		not-accessible	An entry in the sigChanEQsigEQsigSpecificOpTable.
U32 sigChanEQsigSegmentationAccepted	1.3.6.1.4.1.562.2.4.1.115.2.19.1.1	Unsigned32	read-only	This attribute counts the total number of times a long Etsi Qsig message has been received from a PBX and forwarded to a Passport subnet. The value wraps when it reaches its maximum.
U32 sigChanEQsigSegmentationFailed	1.3.6.1.4.1.562.2.4.1.115.2.19.1.2	Unsigned32	read-only	This attribute counts the total number of times a long Etsi Qsig message has been received from a PBX and could not be forwarded as is to a Passport subnet due to end-to-end incompatibility. The value wraps when it reaches its maximum.
vnetEtsiQsigMIB	1.3.6.1.4.1.562.2.4.2.110
vnetEtsiQsigGroup	1.3.6.1.4.1.562.2.4.2.110.1
vnetEtsiQsigGroupBE	1.3.6.1.4.1.562.2.4.2.110.1.5
vnetEtsiQsigGroupBE01	1.3.6.1.4.1.562.2.4.2.110.1.5.2
vnetEtsiQsigGroupBE01A	1.3.6.1.4.1.562.2.4.2.110.1.5.2.2
vnetEtsiQsigCapabilities	1.3.6.1.4.1.562.2.4.2.110.3
vnetEtsiQsigCapabilitiesBE	1.3.6.1.4.1.562.2.4.2.110.3.5
vnetEtsiQsigCapabilitiesBE01	1.3.6.1.4.1.562.2.4.2.110.3.5.2
vnetEtsiQsigCapabilitiesBE01A	1.3.6.1.4.1.562.2.4.2.110.3.5.2.2

RFC description

Manages ETSI QSIG signaling channel configuration for Nortel Magellan Passport voice networking systems.

Start monitoring Nortel Magellan Passport switch / PBX voice trunk signaling interface (ETSI QSIG) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Nortel-Magellan-Passport-VnetEtsiQsigMIB

What Is Nortel-Magellan-Passport-VnetEtsiQsigMIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description