Nortel-Magellan-Passport-BgpMIB

All MIBs › Nortel-Magellan-Passport-BgpMIB

Category: BGP, IP Routing

Description: Manages Nortel Magellan Passport BGP peer sessions, routing policy, and path attribute information.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Nortel-Magellan-Passport-BgpMIB?

Nortel-Magellan-Passport-BgpMIB is a Nortel private MIB for the Magellan Passport family of WAN switches, modeling the BGP (Border Gateway Protocol) component within Passport's virtual-router (Vr/IP) component architecture. Following the Passport component-provisioning pattern, vrIpBgpRowStatusTable (indexed by vrIndex, vrIpIndex, vrIpBgpIndex) controls creation/deletion of a Bgp instance under a given virtual router's IP component, while vrIpBgpProvTable holds its provisionable attributes: vrIpBgpBgpIdentifier (the router's BGP ID drawn from IP address space), vrIpBgpLocalAs, default route-selection tie-breakers (vrIpBgpDefaultLocalPreference, vrIpBgpDefaultMultiExitDisc), route-flap protection (vrIpBgpRouteThrottleLimit, vrIpBgpRouteThrottleInter), and route reflector configuration (vrIpBgpRouteReflector, vrIpBgpRouteReflectorCluster). This gives operators visibility into per-virtual-router BGP peer session policy and route-selection behavior rather than raw route counts. It depends on Nortel-Magellan-Passport-IpMIB and Nortel-Magellan-Passport-VirtualRouterMIB for its vrIndex/vrIpIndex indexing and on Nortel's shared textual-conventions MIBs, and is deployed on Nortel Magellan Passport WAN switches running BGP for multi-VPN or multi-tenant routing, and administrators can download the Nortel-Magellan-Passport-BgpMIB file to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Nortel-Magellan-Passport-BgpMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nortel Magellan Passport WAN switches

Monitoring Examples

An operator polls vrIpBgpRowStatus in vrIpBgpRowStatusTable to confirm a BGP component is active for a given virtual router, then checks vrIpBgpRouteThrottleLimit against observed route churn; if vrIpBgpRouteThrottleInter is frequently triggered along with an unexpected vrIpBgpBgpIdentifier mismatch, it would indicate route flapping or a misconfigured BGP identifier disrupting peering on that virtual router.

What Can Be Monitored

BGP component row status (active/deleted)
BGP identifier and local AS configuration
default local preference and multi-exit-discriminator settings
route throttle limit/interval (flap protection)
route reflector and cluster configuration

Imported Objects

From Nortel-Magellan-Passport-IpMIB

vrIp	OBJECT-IDENTITY
vrIpIndex	OBJECT-TYPE

From Nortel-Magellan-Passport-StandardTextualConventionsMIB

Counter32
DisplayString
Gauge32
Integer32
RowStatus
StorageType
Unsigned32

From Nortel-Magellan-Passport-TextualConventionsMIB

AsciiString
Hex
HexString
IntegerSequence
NonReplicated

From Nortel-Magellan-Passport-UsefulDefinitionsMIB

passportMIBs

OBJECT-IDENTITY

From Nortel-Magellan-Passport-VirtualRouterMIB

vrIndex

OBJECT-TYPE

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
vrIpBgp	1.3.6.1.4.1.562.2.4.1.100.6.21
vrIpBgpRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.1		not-accessible	This entry controls the addition and deletion of vrIpBgp components.
vrIpBgpRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.1.1		not-accessible	A single entry in the table represents a single vrIpBgp component.
ROW vrIpBgpRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of vrIpBgp components. These components can be added and deleted.
STR vrIpBgpComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgp tables.
NON vrIpBgpIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.1.1.10	NonReplicated	not-accessible	This variable represents the index for the vrIpBgp tables.
vrIpBgpPeer	1.3.6.1.4.1.562.2.4.1.100.6.21.2
vrIpBgpPeerRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.2.1		not-accessible	This entry controls the addition and deletion of vrIpBgpPeer components.
vrIpBgpPeerRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.2.1.1		not-accessible	A single entry in the table represents a single vrIpBgpPeer component.
ROW vrIpBgpPeerRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of vrIpBgpPeer components. These components can be added and deleted.
STR vrIpBgpPeerComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpPeerStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgpPeer tables.
IP vrIpBgpPeerPeerAddressIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.2.1.1.10	IpAddress	not-accessible	This variable represents the index for the vrIpBgpPeer tables.
vrIpBgpPeerProvTable	1.3.6.1.4.1.562.2.4.1.100.6.21.2.10		not-accessible	This group contains the provisionable attributes for this BGP Peer component
vrIpBgpPeerProvEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.2.10.1		not-accessible	An entry in the vrIpBgpPeerProvTable.
U32 vrIpBgpPeerPeerAs	1.3.6.1.4.1.562.2.4.1.100.6.21.2.10.1.1	Unsigned32	read-write	This attribute specifies the autonomous system identifier of this BGP Peer component. It will be used to verify the autonomous system identifier learned from the peer through the OPEN message. The peer connection will be rejected and a NOTIFICATION message will be sent to the peer if these two numbers don't match.
IP vrIpBgpPeerLocalAddressConfigured	1.3.6.1.4.1.562.2.4.1.100.6.21.2.10.1.2	IpAddress	read-write	This attribute specifies the local IP address configured for this Bgp Peer connection. If this attribute is 0.0.0.0, TCP will choose a local IP interface based on the remote IP address of this peer connection and the IP forwarding table. The value chosen is stored in the localAddressUsed attribute under the same Peer component.
U32 vrIpBgpPeerKeepAliveConfigured	1.3.6.1.4.1.562.2.4.1.100.6.21.2.10.1.3	Unsigned32	read-write	This attribute specifies the configured interval in seconds, between BGP KEEPALIVE message retransmissions. It is used to establish the ratio between keepalive interval and hold time. If this attribute is zero, then the holdTimeConfigured attribute should also be zero, which means that periodic KEEPALIVE messages will not be sent.
U32 vrIpBgpPeerHoldTimeConfigured	1.3.6.1.4.1.562.2.4.1.100.6.21.2.10.1.4	Unsigned32	read-write	This attribute specifies the maximum time in seconds, that may elapse without receiving a KEEPALIVE or UPDATE message before the connection is considered down. The hold time must be either zero or at least three seconds. If this attribute is zero, then the keepAliveConfigured attribute should also be zero, which means that periodic KEEPALIVE messages will not be sent.
U32 vrIpBgpPeerConnectRetryTime	1.3.6.1.4.1.562.2.4.1.100.6.21.2.10.1.5	Unsigned32	read-write	This attribute specifies the time interval in seconds for the ConnectRetry timer. It is the minimum amount of time that must elapse between successive TCP connection retries for establishing BGP peer connection.
U32 vrIpBgpPeerMinAsOrigTime	1.3.6.1.4.1.562.2.4.1.100.6.21.2.10.1.6	Unsigned32	read-write	This attribute specifies the time interval in seconds for the MinAsOriginationInterval timer. It is the minimum amount of time that must elapse between updates that advertise a change to a route within the local autonomous system to neighboring autonomous systems.
U32 vrIpBgpPeerMinRouteAdvTime	1.3.6.1.4.1.562.2.4.1.100.6.21.2.10.1.7	Unsigned32	read-write	This attribute specifies the time interval in seconds for the MinRouteAdvertisementInterval timer. Feasible routes received from peers in other autonomous systems may only be re-advertised to peers in other autonomous systems at a rate no greater than MinRouteAdvertisementInterval.
U32 vrIpBgpPeerDefaultInAggMed	1.3.6.1.4.1.562.2.4.1.100.6.21.2.10.1.8	Unsigned32	read-write	This attribute specifies this Bgp Peer component instance's metric for generating a dynamic default route whenever this external bgp peer got established. It is used to prioritize between the dynamic default routes generated by Passport Bgp speakers. If this attribute is not set, Bgp will not generate a dynamic default route. If this attribute is set, Bgp will automatically generate a dynamic default route when the connection established.
INT vrIpBgpPeerIsRouteReflectorClient	1.3.6.1.4.1.562.2.4.1.100.6.21.2.10.1.9	INTEGER	read-write	This attribute specifies whether the peer is a client peer or non- client peer of this Bgp instance. The attribute is only meaningful if attribute routeReflector of Bgp is true.
vrIpBgpPeerStateTable	1.3.6.1.4.1.562.2.4.1.100.6.21.2.11		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
vrIpBgpPeerStateEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.2.11.1		not-accessible	An entry in the vrIpBgpPeerStateTable.
INT vrIpBgpPeerAdminState	1.3.6.1.4.1.562.2.4.1.100.6.21.2.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT vrIpBgpPeerOperationalState	1.3.6.1.4.1.562.2.4.1.100.6.21.2.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT vrIpBgpPeerUsageState	1.3.6.1.4.1.562.2.4.1.100.6.21.2.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
vrIpBgpPeerOperTable	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12		not-accessible	This group contains the operational attributes for the Peer component.
vrIpBgpPeerOperEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1		not-accessible	An entry in the vrIpBgpPeerOperTable.
INT vrIpBgpPeerConnectionState	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.3	INTEGER	read-only	This attribute indicates the current state of this BGP peer connection. The meaning of each state is as follows: idle - it is the initial state of the BGP peer connection. Error events will also cause BGP peer connection to transit to the idle state. connect - BGP has initiated a TCP connection request to this peer, and waiting for reply from that peer. active - BGP is not initiating a TCP connection request to this peer, because TCP connection failed and is waiting for connection retry time-out. openSent - a TCP connection to this peer has been established, but the OPEN message has not been successfully exchanged. openConfirm - OPEN message has been successfully exchanged with this peer, but the first KEEPALIVE message has not been received from that peer. established - the first KEEPALIVE message has been received from this peer, which means this BGP peer connection has been established. See RFC 1771 for a detailed description of BGP state transitions.
IP vrIpBgpPeerBgpIdentifier	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.4	IpAddress	read-only	This attribute indicates the BGP Identifier of this Bgp Peer component. It is learned from the peer through the OPEN message.
U32 vrIpBgpPeerVersionNegotiated	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.5	Unsigned32	read-only	This attribute indicates the BGP version number negotiated with this peer through the OPEN message. Currently, only BGP version 4 is supported. BGP will reject the peer connection if our peer proposes a BGP version other than 4.
U32 vrIpBgpPeerHoldTimeNegotiated	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.6	Unsigned32	read-only	This attribute indicates the maximum time in seconds, that may elapse without receiving a KEEPALIVE or UPDATE message before the connection is considered down. This is the negotiated value with peer through the OPEN message. The hold time must be either zero or at least three seconds. If the negotiated hold time is zero, then periodic KEEPALIVE messages are not expected from the peer.
U32 vrIpBgpPeerKeepAliveNegotiated	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.7	Unsigned32	read-only	This attribute indicates the interval in seconds, between BGP KEEPALIVE message retransmissions. This keepalive interval will have the same ratio to the hold time negotiated with the peer as that of the locally configured keepalive and hold time. This attribute will be zero if the holdTimeNegotiated attribute is zero, which means periodic KEEPALIVE messages will not be sent.
IP vrIpBgpPeerLocalAddressUsed	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.8	IpAddress	read-only	This attribute indicates the local IP address used for this BGP peer connection. If the localAddressConfigured attribute is non-zero, its value will be used. Otherwise, the local address will be assigned by TCP based on the remote IP address of this peer connection and the IP forwarding table.
U32 vrIpBgpPeerLocalPort	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.9	Unsigned32	read-only	This attribute indicates the local TCP port for the connection between the BGP peers.
U32 vrIpBgpPeerRemotePort	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.10	Unsigned32	read-only	This attribute indicates the remote TCP port for the connection between the BGP peers.
STR vrIpBgpPeerLastError	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.11	HexString	read-only	This attribute indicates the last error code and subcode seen by this Bgp component instance on this peer connection. The first byte of this two byte OCTET STRING contains the error code, and the second byte contains the subcode. A value of zero means that no error has occurred. Check RFC 1771 for mappings of error codes and error subcodes.
G32 vrIpBgpPeerConnectionEstablishedTime	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.12	Gauge32	read-only	This attribute indicates how long since this Peer component's last transition to or from the established state. It is set to zero when the Peer component is activated. DESCRIPTION
C32 vrIpBgpPeerConnectionEstablishedTransitions	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.13	Counter32	read-only	This attribute counts the total number of times the BGP connection state transitioned into the established state.
G32 vrIpBgpPeerInUpdateElapsedTime	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.14	Gauge32	read-only	This attribute indicates the elapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time inUpdates attribute is incremented, the value of this attribute is set to zero.
C32 vrIpBgpPeerInMsgs	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.15	Counter32	read-only	This attribute counts the number of BGP messages received without error from the BGP peer. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpPeerInUpdates	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.16	Counter32	read-only	This attribute counts the number of BGP UPDATE messages received on this peer connection. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpPeerInErrors	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.17	Counter32	read-only	This attribute counts the number of messages received from this BGP peer that proved to be in error. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpPeerInErrorMsgs	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.18	Counter32	read-only	This attribute counts the number of BGP NOTIFICATION messages received from this BGP peer. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpPeerOutMsgs	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.19	Counter32	read-only	This attribute counts the number of locally generated BGP messages sent to this BGP peer. It does not include discarded messages. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpPeerOutUpdates	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.20	Counter32	read-only	This attribute counts the number of BGP UPDATE messages sent to this peer. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpPeerOutDiscards	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.21	Counter32	read-only	This attribute counts the number of locally generated BGP messages not sent to this BGP peer due to resource limitations within a BGP entity. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpPeerOutErrorMsgs	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.22	Counter32	read-only	This attribute counts the number of BGP NOTIFICATION messages sent to this BGP peer. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpPeerInRoutes	1.3.6.1.4.1.562.2.4.1.100.6.21.2.12.1.23	Counter32	read-only	This attribute indicates the number of routes received from this BGP peer.
vrIpBgpImport	1.3.6.1.4.1.562.2.4.1.100.6.21.3
vrIpBgpImportRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.3.1		not-accessible	This entry controls the addition and deletion of vrIpBgpImport components.
vrIpBgpImportRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.3.1.1		not-accessible	A single entry in the table represents a single vrIpBgpImport component.
ROW vrIpBgpImportRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of vrIpBgpImport components. These components can be added and deleted.
STR vrIpBgpImportComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpImportStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgpImport tables.
I32 vrIpBgpImportIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.3.1.1.10	Integer32	not-accessible	This variable represents the index for the vrIpBgpImport tables.
vrIpBgpImportNet	1.3.6.1.4.1.562.2.4.1.100.6.21.3.2
vrIpBgpImportNetRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.3.2.1		not-accessible	This entry controls the addition and deletion of vrIpBgpImportNet components.
vrIpBgpImportNetRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.3.2.1.1		not-accessible	A single entry in the table represents a single vrIpBgpImportNet component.
ROW vrIpBgpImportNetRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.3.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of vrIpBgpImportNet components. These components can be added and deleted.
STR vrIpBgpImportNetComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.3.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpImportNetStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.3.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgpImportNet tables.
I32 vrIpBgpImportNetIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.3.2.1.1.10	Integer32	not-accessible	This variable represents the index for the vrIpBgpImportNet tables.
vrIpBgpImportNetProvTable	1.3.6.1.4.1.562.2.4.1.100.6.21.3.2.10		not-accessible	This group contains the set of provisionable attributes for the Network component.
vrIpBgpImportNetProvEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.3.2.10.1		not-accessible	An entry in the vrIpBgpImportNetProvTable.
IP vrIpBgpImportNetPrefix	1.3.6.1.4.1.562.2.4.1.100.6.21.3.2.10.1.1	IpAddress	read-write	This attribute specifies the network prefix whose length is determined by the length attribute under the same Network component.
U32 vrIpBgpImportNetLength	1.3.6.1.4.1.562.2.4.1.100.6.21.3.2.10.1.2	Unsigned32	read-write	This attribute specifies the length of the network prefix.
vrIpBgpImportProvTable	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10		not-accessible	This group contains all the provisionable attributes for the Import component.
vrIpBgpImportProvEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1		not-accessible	An entry in the vrIpBgpImportProvTable.
U32 vrIpBgpImportPeerAs	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1.1	Unsigned32	read-write	This key attribute specifies the autonomous system number of the peer from which the routes are learned. A value of 0 for this attribute means that peer AS number will match any AS number.
IP vrIpBgpImportPeerIpAddress	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1.2	IpAddress	read-write	This key attribute specifies the IP address of the peer from which the routes are learned. A value of 0.0.0.0 for this attribute means that peer IP address will match any IP address.
U32 vrIpBgpImportOriginAs	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1.3	Unsigned32	read-write	This key attribute specifies the autonomous system number where the routes were originated. A value of 0 for this attribute means origin AS number will match any AS number.
INT vrIpBgpImportOriginProtocol	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1.4	INTEGER	read-write	This key attribute specifies the protocols that originated the routes. A value of incomplete for this attribute means this information is not available.
INT vrIpBgpImportUsageFlag	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1.5	INTEGER	read-write	This attribute specifies whether BGP will use, ignore, or exclude information in received update if it meets criteria specified by the key attributes of this component. When it is set to exclude the matching routes if selected are installed in the routing database and forwarding table with an unreachable next hop.
U32 vrIpBgpImportLocalPreference	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1.6	Unsigned32	read-write	This attribute specifies this Bgp component instance's degree of preference for those routes that match the criteria of this import policy. A higher value indicates a more preferred route. A value of 0 for this attribute means that the default local preference value provisioned under the Bgp component should be used.
INT vrIpBgpImportPreferredOver	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1.7	INTEGER	read-write	This attribute indicates the preference of the external BGP route with the OSPF internal route. overIntOspf means that the external BGP route is chosen over OSPF internal route, while underIntOspf means that the OSPF internal route is chosen over the external BGP route. The default preference is set to underIntOspf.
STR vrIpBgpImportAsPathExpression	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1.8	AsciiString	read-write	This key attribute allows the user to enter a regular expression to match the import AS Path Attribute of the received update message. Note: the AS Path Attribute lists the ASs in reverse traversal order. The syntax of the regular expression is a subset of the RFC 2280. The basic syntax of a regular expression is a list of AS number separated by a space which making up a AS path. The following characters has the special meaning: '.' - Matches any AS number. '^n' - Matches the first AS item (n) in the AS Path Attribute, or in order words, matches the last AS (n) traversed in the AS path. 'n$' - Matches the last AS item (n) in the AS Path Attribute, or in order words, matches the first AS (n) traversed in the AS path. '[n1 ... n2]' - Matches any AS number that appeared in the set n1 ... n2. 'n1 - n2' - Matches any AS number between the range of n1 and n2. '()' - is supported to change the order of evaluation. 'n' - Matches 0 or more occurrences of n, where n can be a set, range or AS number. 'n+' - Matches 1 or more occurrences of n, where n can be a set, range or AS number. 'n?' - Matches 0 or 1 occurrences of n, where n can be a AS set, range or number. The following logical operators are evaluated in decending order: 'NOT' - Given a regular expression x, NOT x matches the AS number pattern that is not matched by x. 'AND' - Given two regular expressions x and y, x AND y matches the intersection of the AS path that are matched by x and those are matched by y. 'OR' - Given two regular expressions x and y, x OR y matches the union of the AS path that are matched by x and those are matched by y. For example: The AS path '5 4 3 2 1', where 1 is the origin AS, would be matched by any one of the following regular expressions: 1$, ^5, 4 3, 5 3 - 4, 5 [4 3 2] not10 2 1, not (6 7 8 9 10) and 5 4 .* 1 Empty regular expression implies a match on all AS path.
STR vrIpBgpImportCommunityExpression	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1.9	AsciiString	read-write	This key attribute allows the user to enter a regular expression to match the import Community Attribute of the received update message. The syntax of the regular expression is a subset of the RFC 2280. The basic syntax of a regular expression is a list of Community number seperated by a space which making up a Community attribute. The following characters has the special meaning: '[n1 ... n2]' - Matches any Community number that appeared in the set n1 ... n2. 'n1 - n2' - Matches any Community number between the range of n1 and n2. '()' - is supported to change the order of evaluation. 'n' - Matches 0 or more occurrences of n, where n can be a set, range or Community number. 'n+' - Matches 1 or more occurrences of n, where n can be a set, range or Community number. 'n?' - Matches 0 or 1 occurrences of n, where n can be a set, range or number. The following logical operators are evaluated in decending order: 'NOT' - Given a regular expression x, NOT x matches the Community attribute that is not matched by x. 'AND' - Given two regular expressions x and y, x AND y matches the intersection of the Community attribute that are matched by x and those are matched by y. 'OR' - Given two regular expressions x and y, x OR y matches the union of the Community attribute that are matched by x and those are matched by y. For example: The Community path '1 2 3 4 5'would be matched by any one of the following regular expressions: 1, 5, 4 3, 2 3 - 4, 1 [3 4 2]+ , not (6 7 8 9 10) and 1 2 Empty regular expression implies a match on all Community path.
U32 vrIpBgpImportExpressPreference	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1.10	Unsigned32	read-write	This attribute specifies the relative preference of the policy which use the keys expressAsPath and expressCommunity. This attribute is ignored if attributes expressAsPath and expressCommunity are both empty. This attribute is used to break the tie when two import policies' expression attributes match a specific AS Path or Community. A higher value indicates a more preferred policy.
U32 vrIpBgpImportAppendCommunity	1.3.6.1.4.1.562.2.4.1.100.6.21.3.10.1.11	Unsigned32	read-write	This attribute indicates which community number this Import policy will send along with the Path Attribute. Refer to RFC 1997 for the detailed description of how this attribute may be used to pass additional information to BGP peers. If the value is set to 0, no community is appended to the Community attribute.
vrIpBgpExport	1.3.6.1.4.1.562.2.4.1.100.6.21.4
vrIpBgpExportRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.4.1		not-accessible	This entry controls the addition and deletion of vrIpBgpExport components.
vrIpBgpExportRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.4.1.1		not-accessible	A single entry in the table represents a single vrIpBgpExport component.
ROW vrIpBgpExportRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.4.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of vrIpBgpExport components. These components can be added and deleted.
STR vrIpBgpExportComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpExportStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgpExport tables.
I32 vrIpBgpExportIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.4.1.1.10	Integer32	not-accessible	This variable represents the index for the vrIpBgpExport tables.
vrIpBgpExportNet	1.3.6.1.4.1.562.2.4.1.100.6.21.4.2
vrIpBgpExportNetRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.4.2.1		not-accessible	This entry controls the addition and deletion of vrIpBgpExportNet components.
vrIpBgpExportNetRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.4.2.1.1		not-accessible	A single entry in the table represents a single vrIpBgpExportNet component.
ROW vrIpBgpExportNetRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.4.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of vrIpBgpExportNet components. These components can be added and deleted.
STR vrIpBgpExportNetComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.4.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpExportNetStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.4.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgpExportNet tables.
I32 vrIpBgpExportNetIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.4.2.1.1.10	Integer32	not-accessible	This variable represents the index for the vrIpBgpExportNet tables.
vrIpBgpExportNetProvTable	1.3.6.1.4.1.562.2.4.1.100.6.21.4.2.10		not-accessible	This group contains the set of provisionable attributes for the Network component.
vrIpBgpExportNetProvEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.4.2.10.1		not-accessible	An entry in the vrIpBgpExportNetProvTable.
IP vrIpBgpExportNetPrefix	1.3.6.1.4.1.562.2.4.1.100.6.21.4.2.10.1.1	IpAddress	read-write	This attribute specifies the network prefix whose length is determined by the length attribute under the same Network component.
U32 vrIpBgpExportNetLength	1.3.6.1.4.1.562.2.4.1.100.6.21.4.2.10.1.2	Unsigned32	read-write	This attribute specifies the length of the network prefix.
vrIpBgpExportProvTable	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10		not-accessible	This group contains all the provisioned attributes for the Export component.
vrIpBgpExportProvEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1		not-accessible	An entry in the vrIpBgpExportProvTable.
U32 vrIpBgpExportPeerAs	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.1	Unsigned32	read-write	This key attribute specifies the autonomous system number of the peer where the routes are advertised to. A value of 0 for this attribute means this export policy applies to all peer ASes.
IP vrIpBgpExportPeerIpAddress	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.2	IpAddress	read-write	This key attribute specifies the IP address of the peer where the routes are advertised to. A value of 0.0.0.0 for this attribute means this export policy applies to all peers.
INT vrIpBgpExportProtocol	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.3	INTEGER	read-write	This key attribute specifies which protocol the export policy applies to. If it is set to all, that means this export policy will apply all routes in the IP routing table. Example: vr/1 ip ospf export/1 with advertise Status = block protocol = bgpExternal bgpAsId = 3 peerAs = 5 This policy specifies that all routes learned from EBGP Peers that are originated from AS 3 should not be advertised to AS 5.
U32 vrIpBgpExportEgpAsId	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.4	Unsigned32	read-write	This key attribute specifies the EGP autonomous system number that this export policy will apply to. When this value is non-zero, the protocol attribute must be set to egp.
U32 vrIpBgpExportBgpAsId	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.5	Unsigned32	read-write	This key attribute specifies the BGP autonomous system number that this export policy will apply to. When this value is non-zero, the protocol attribute must be set to either bgpInternal or bgpExternal.
HEX vrIpBgpExportOspfTag	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.6	Hex	read-write	This key attribute specifies the OSPF tag when the protocol attribute is set to either ospfInternal or ospfExternal. The default tag value 4294967295 (FFFFFFFF in hex) indicates that the tag not specified.
IP vrIpBgpExportRipInterface	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.7	IpAddress	read-write	This key attribute specifies the local RIP interface where the routes are learned from. The ripInterface attribute when non-zero should be equal to one of the IP addresses provisioned as a logicalIf component under IpPort. Otherwise, this policy will be ignored. The value of the protocol attribute must be set to rip if a value for the ripInterface attribute is non-zero.
IP vrIpBgpExportRipNeighbor	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.8	IpAddress	read-write	This key attribute specifies the RIP neighbor where the routes were learned from. The value of the protocol attribute must be set to rip if a value for the ripNeighbor attribute is non-zero.
INT vrIpBgpExportAdvertiseStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.9	INTEGER	read-write	This attribute specifies whether data will be exported if it meets criteria specified by the other key attributes of this component.
U32 vrIpBgpExportMultiExitDisc	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.10	Unsigned32	read-write	This attribute specifies this Bgp component instance's metric to discriminate between multiple exit points to an adjacent autonomous system if the route meets the criteria specified by the key attributes of this component. A lower value indicates a more preferred route. A value of 0 for this attribute means the default MED value provisioned under the Bgp component should be used.
INT vrIpBgpExportSendMultiExitDiscToEbgp	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.11	INTEGER	read-write	This attribute specifies whether the Multi Exit Discriminator(MED) attribute should be included in an update message sent to an EBGP peer.
STR vrIpBgpExportAsPathExpression	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.12	AsciiString	read-write	This key attribute allows the user to enter a regular expression to match the import AS Path Attribute of the export update message. Note: the AS Path Attribute lists the ASs in reverse traversal order. The syntax of the regular expression is a subset of the RFC 2280. The basic syntax of a regular expression is a list of AS number separated by a space which making up a AS path. The following characters has the special meaning: '.' - Matches any AS number. '^n' - Matches the first AS item (n) in the AS Path Attribute, or in order words, matches the last AS (n) traversed in the AS path. 'n$' - Matches the last AS item (n) in the AS Path Attribute, or in order words, matches the first AS (n) traversed in the AS path. '[n1 ... n2]' - Matches any AS number that appeared in the set n1 ... n2. 'n1 - n2' - Matches any AS number between the range of n1 and n2. '()' - is supported to change the order of evaluation. 'n' - Matches 0 or more occurrences of n, where n can be a set, range or AS number. 'n+' - Matches 1 or more occurrences of n, where n can be a set, range or AS number. 'n?' - Matches 0 or 1 occurrences of n, where n can be a set, range or number. The following logical operators are evaluated in decending order: 'NOT' - Given a regular expression x, NOT x matches the AS number pattern that is not matched by x. 'AND' - Given two regular expressions x and y, x AND y matches the intersection of the AS path that are matched by x and those are matched by y. 'OR' - Given two regular expressions x and y, x OR y matches the union of the AS path that are matched by x and those are matched by y. For example: The AS path '5 4 3 2 1', where 1 is the origin AS, would be matched by any one of the following regular expressions: 1$, ^5, 4 3, 5 3 - 4, 5 [4 3 2] not10 2 1, not (6 7 8 9 10) and 5 4 .* 1 Empty regular expression implies a match on all AS path.
STR vrIpBgpExportCommunityExpression	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.13	AsciiString	read-write	This key attribute allows the user to enter a regular expression to match the import Community Attribute of the received update message. The syntax of the regular expression is a subset of the RFC 2280. The basic syntax of a regular expression is a list of Community number seperated by a space which making up a Community attribute. The following characters has the special meaning: '[n1 ... n2]' - Matches any Community number that appeared in the set n1 ... n2. 'n1 - n2' - Matches any Community number between the range of n1 and n2. '()' - is supported to change the order of evaluation. 'n' - Matches 0 or more occurrences of n, where n can be a set, range or Community number. 'n+' - Matches 1 or more occurrences of n, where n can be a set, range or Community number. 'n?' - Matches 0 or 1 occurrences of n, where n can be a set, range or number. The following logical operators are evaluated in decending order: 'NOT' - Given a regular expression x, NOT x matches the Community attribute that is not matched by x. 'AND' - Given two regular expressions x and y, x AND y matches the intersection of the Community attribute that are matched by x and those are matched by y. 'OR' - Given two regular expressions x and y, x OR y matches the union of the Community attribute that are matched by x and those are matched by y. For example: The Community path '1 2 3 4 5' would be match by any one of the following regular expressions: 4 3, 2 3 - 4, 1 [3 4 2]+ 4, not (6 7 8 9 10) and 1 2 Empty regular expression implies a match on all Community path.
U32 vrIpBgpExportExpressPreference	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.14	Unsigned32	read-write	This attribute specifies the relative preference of the policy which use the keys expressAsPath and expressCommunity. This attribute is ignored if attributes expressAsPath and expressCommunity are both empty. This attribute is used to break the tie when two export policies' expression attributes match a specific AS Path or Community. A higher value indicates a more preferred policy.
U32 vrIpBgpExportSendCommunity	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.15	Unsigned32	read-write	This attribute indicates which community number this Export policy will send along with the Path Attribute. Refer to RFC 1997 for the detailed description of how this attribute may be used to pass additional information to BGP peers. If the value is set to 0, no community is added to the Community attribute.
NUM vrIpBgpExportInsertDummyAs	1.3.6.1.4.1.562.2.4.1.100.6.21.4.10.1.200	IntegerSequence	read-write	This attribute specifies the AS number(s) to be inserted into the AS Path Attribute. The value is a seuence of AS number seperated by period(.). For example, if the value is 20.20.30, the AS numbers 20, 20 and 30 would be inserted at the end of the AS Path Attribute just before the local AS number.
vrIpBgpAs	1.3.6.1.4.1.562.2.4.1.100.6.21.5
vrIpBgpAsRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.5.1		not-accessible	This entry controls the addition and deletion of vrIpBgpAs components.
vrIpBgpAsRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.5.1.1		not-accessible	A single entry in the table represents a single vrIpBgpAs component.
ROW vrIpBgpAsRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.5.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of vrIpBgpAs components. These components can be added and deleted.
STR vrIpBgpAsComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.5.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpAsStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.5.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgpAs tables.
I32 vrIpBgpAsIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.5.1.1.10	Integer32	not-accessible	This variable represents the index for the vrIpBgpAs tables.
vrIpBgpAsProvTable	1.3.6.1.4.1.562.2.4.1.100.6.21.5.10		not-accessible	This group contains the attributes associated to each autonomous system for this Bgp component instance.
vrIpBgpAsProvEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.5.10.1		not-accessible	An entry in the vrIpBgpAsProvTable.
U32 vrIpBgpAsWeight	1.3.6.1.4.1.562.2.4.1.100.6.21.5.10.1.1	Unsigned32	read-write	This attribute specifies the weight for an autonomous system. It allows users to prefer some ASes over others. It is used in route selection. Lowest weight is preferred. Setting the weight of an AS to 255 will make any route that traverses through that AS unpreferred.
vrIpBgpAggregate	1.3.6.1.4.1.562.2.4.1.100.6.21.6
vrIpBgpAggregateRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.6.1		not-accessible	This entry controls the addition and deletion of vrIpBgpAggregate components.
vrIpBgpAggregateRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.6.1.1		not-accessible	A single entry in the table represents a single vrIpBgpAggregate component.
ROW vrIpBgpAggregateRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.6.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of vrIpBgpAggregate components. These components can be added and deleted.
STR vrIpBgpAggregateComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.6.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpAggregateStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.6.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgpAggregate tables.
IP vrIpBgpAggregatePrefixIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.6.1.1.10	IpAddress	not-accessible	This variable represents an index for the vrIpBgpAggregate tables.
I32 vrIpBgpAggregateLengthIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.6.1.1.11	Integer32	not-accessible	This variable represents an index for the vrIpBgpAggregate tables.
vrIpBgpAggregateNet	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2
vrIpBgpAggregateNetRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.1		not-accessible	This entry controls the addition and deletion of vrIpBgpAggregateNet components.
vrIpBgpAggregateNetRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.1.1		not-accessible	A single entry in the table represents a single vrIpBgpAggregateNet component.
ROW vrIpBgpAggregateNetRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of vrIpBgpAggregateNet components. These components can be added and deleted.
STR vrIpBgpAggregateNetComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpAggregateNetStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgpAggregateNet tables.
I32 vrIpBgpAggregateNetIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.1.1.10	Integer32	not-accessible	This variable represents the index for the vrIpBgpAggregateNet tables.
vrIpBgpAggregateNetProvTable	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.10		not-accessible	This group contains the set of provisionable attributes for the Network component.
vrIpBgpAggregateNetProvEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.10.1		not-accessible	An entry in the vrIpBgpAggregateNetProvTable.
IP vrIpBgpAggregateNetPrefix	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.10.1.1	IpAddress	read-write	This attribute specifies the network prefix whose length is determined by the length attribute under the same Network component.
U32 vrIpBgpAggregateNetLength	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.10.1.2	Unsigned32	read-write	This attribute specifies the length of the network prefix.
INT vrIpBgpAggregateNetProtocol	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.10.1.3	INTEGER	read-write	This attribute specifies the IP protocols to which this route should belong.
U32 vrIpBgpAggregateNetEgpAsId	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.10.1.4	Unsigned32	read-write	This attribute specifies an EGP autonomous system number. When this value is non-zero, the protocol attribute must be set to either egp or to all. And this more specific route will be advertised together with the aggregated route only if it is learned through egp and this attribute matches the EGP autonomous system number where the network is learned from. The default value 0 indicates that the EGP autonomous system number is not specified.
U32 vrIpBgpAggregateNetBgpAsId	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.10.1.5	Unsigned32	read-write	This attribute specifies the BGP autonomous system number. When this value is non-zero, the protocol attribute must be set to either bgp or to all. And this more specific route will be advertised together with the aggregated route only if it is learned through BGP and this attribute matches the BGP autonomous system number where the network is learned from. The default value 0 indicates that the BGP autonomous system number is not specified.
HEX vrIpBgpAggregateNetOspfTag	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.10.1.6	Hex	read-write	This attribute specifies the OSPF tag. When this attribute is set to a value other than the default value FFFFFFFF in hex, the protocol attribute must be set to either ospf or to all. And this more specific route will be advertised together with the aggregated route only if its OSPF tag matches this value. The default tag value 4294967295 (FFFFFFFF in hex) indicates that the tag is not specified.
IP vrIpBgpAggregateNetRipInterface	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.10.1.7	IpAddress	read-write	This attribute specifies a local RIP interface which should be equal to one of the IP addresses provisioned as a logicalIf component under IpPort. When this value is non-zero, the value of the protocol attribute must be either set to rip or to all. And this more specific route will be advertised together with the aggregated route only if it is learned through RIP and this RIP interface. The default value 0.0.0.0 indicates that the RIP interface is not specified.
INT vrIpBgpAggregateNetAction	1.3.6.1.4.1.562.2.4.1.100.6.21.6.2.10.1.8	INTEGER	read-write	This attribute specifies whether this network should be aggregated or advertised out.
vrIpBgpIndb	1.3.6.1.4.1.562.2.4.1.100.6.21.7
vrIpBgpIndbRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.7.1		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This entry controls the addition and deletion of vrIpBgpIndb components.
vrIpBgpIndbRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.7.1.1		not-accessible	A single entry in the table represents a single vrIpBgpIndb component.
ROW vrIpBgpIndbRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.7.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of vrIpBgpIndb components. These components cannot be added nor deleted.
STR vrIpBgpIndbComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.7.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpIndbStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.7.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgpIndb tables.
IP vrIpBgpIndbPrefixIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.7.1.1.10	IpAddress	not-accessible	This variable represents an index for the vrIpBgpIndb tables.
I32 vrIpBgpIndbLengthIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.7.1.1.11	Integer32	not-accessible	This variable represents an index for the vrIpBgpIndb tables.
IP vrIpBgpIndbPeerIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.7.1.1.12	IpAddress	not-accessible	This variable represents an index for the vrIpBgpIndb tables.
vrIpBgpIndbOperTable	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This group contains all the operational attributes of the IndbEntry component.
vrIpBgpIndbOperEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1		not-accessible	An entry in the vrIpBgpIndbOperTable.
INT vrIpBgpIndbOrigin	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.4	INTEGER	read-only	This attribute indicates the ultimate origin of the path information. A value of incomplete means this information is not available.
INT vrIpBgpIndbInLocaldb	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.5	INTEGER	read-only	This attribute indicates whether or not this route was chosen as the best BGP4 route.
IP vrIpBgpIndbNextHop	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.6	IpAddress	read-only	This attribute indicates the IP address of the border router that should be used as the next hop for the destination network.
U32 vrIpBgpIndbLocalPreference	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.7	Unsigned32	read-only	This attribute indicates our IBGP peer's degree of preference for an advertised route. A higher value indicates a more preferred route.
U32 vrIpBgpIndbCalcLocalPref	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.8	Unsigned32	read-only	This attribute indicates our degree of preference for this route. A higher value indicates a more preferred route.
U32 vrIpBgpIndbMultiExitDiscriminator	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.9	Unsigned32	read-only	This attribute indicates a metric used to discriminate between multiple exit points to the same adjacent autonomous system. A lower value indicates a more preferred route.
INT vrIpBgpIndbAtomicAggregate	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.10	INTEGER	read-only	This attribute indicates whether or not the local system has selected a less specific route without selecting a more specific route.
U32 vrIpBgpIndbAggregatorAs	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.11	Unsigned32	read-only	This attribute indicates the AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute.
IP vrIpBgpIndbAggregatorAddr	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.12	IpAddress	read-only	This attribute indicates the IP address of the last BGP4 speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute.
STR vrIpBgpIndbAsPath	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.13	AsciiString	read-only	This attribute indicates the sequence of AS path segments. The AS Path Attribute lists the ASs in reverse traversal order.
STR vrIpBgpIndbUnknownAttributes	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.14	AsciiString	read-only	This attribute indicates all the path attributes not understood by this Bgp component instance.
STR vrIpBgpIndbCommunityPath	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.15	AsciiString	read-only	This attribute indicates the Community path attribute.
IP vrIpBgpIndbAsOriginatorId	1.3.6.1.4.1.562.2.4.1.100.6.21.7.10.1.16	IpAddress	read-only	This attribute is associated with the Route Reflector. It indicates the router-id of the originator in the local AS. A value of 0.0.0.0 indicates this attribute is not present in the learned IBGP route or if this Bgp instance is not a Route Reflector.
vrIpBgpIndbRrClusterListTable	1.3.6.1.4.1.562.2.4.1.100.6.21.7.798		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This attribute indicates a sequence of cluster-ids that the route has traversed. A blank list indicates this attribute is not present in the learned IBGP route or if this Bgp instance is not a Route Reflector.
vrIpBgpIndbRrClusterListEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.7.798.1		not-accessible	An entry in the vrIpBgpIndbRrClusterListTable.
IP vrIpBgpIndbRrClusterListValue	1.3.6.1.4.1.562.2.4.1.100.6.21.7.798.1.1	IpAddress	read-only	This variable represents both the value and the index for the vrIpBgpIndbRrClusterListTable.
vrIpBgpLocaldb	1.3.6.1.4.1.562.2.4.1.100.6.21.8
vrIpBgpLocaldbRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.8.1		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This entry controls the addition and deletion of vrIpBgpLocaldb components.
vrIpBgpLocaldbRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.8.1.1		not-accessible	A single entry in the table represents a single vrIpBgpLocaldb component.
ROW vrIpBgpLocaldbRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.8.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of vrIpBgpLocaldb components. These components cannot be added nor deleted.
STR vrIpBgpLocaldbComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.8.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpLocaldbStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.8.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgpLocaldb tables.
IP vrIpBgpLocaldbPrefixIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.8.1.1.10	IpAddress	not-accessible	This variable represents an index for the vrIpBgpLocaldb tables.
I32 vrIpBgpLocaldbLengthIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.8.1.1.11	Integer32	not-accessible	This variable represents an index for the vrIpBgpLocaldb tables.
IP vrIpBgpLocaldbPeerIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.8.1.1.12	IpAddress	not-accessible	This variable represents an index for the vrIpBgpLocaldb tables.
vrIpBgpLocaldbOperTable	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This group contains all the operational attributes of the LocaldbEntry component.
vrIpBgpLocaldbOperEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1		not-accessible	An entry in the vrIpBgpLocaldbOperTable.
INT vrIpBgpLocaldbOrigin	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1.4	INTEGER	read-only	This attribute indicates the ultimate origin of the path information. A value of incomplete means this information is not available.
IP vrIpBgpLocaldbNextHop	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1.5	IpAddress	read-only	This attribute indicates the IP address of the border router that should be used as the next hop for the destination network.
U32 vrIpBgpLocaldbLocalPreference	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1.6	Unsigned32	read-only	This attribute indicates our IBGP peer's degree of preference for an advertised route. A higher value indicates a more preferred route.
U32 vrIpBgpLocaldbMultiExitDiscriminator	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1.7	Unsigned32	read-only	This attribute indicates a metric used to discriminate between multiple exit points to the same adjacent autonomous system. A lower value indicates a more preferred route.
INT vrIpBgpLocaldbAtomicAggregate	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1.8	INTEGER	read-only	This attribute indicates whether or not the local system has selected a less specific route without selecting a more specific route.
U32 vrIpBgpLocaldbAggregatorAs	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1.9	Unsigned32	read-only	This attribute indicates the AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute.
IP vrIpBgpLocaldbAggregatorAddr	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1.10	IpAddress	read-only	This attribute indicates the IP address of the last BGP4 speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute.
STR vrIpBgpLocaldbAsPath	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1.11	AsciiString	read-only	This attribute indicates the sequence of AS path segments. The AS Path Attribute lists the ASs in reverse traversal order.
STR vrIpBgpLocaldbUnknownAttributes	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1.12	AsciiString	read-only	This attribute indicates all the path attributes not understood by this Bgp component instance.
STR vrIpBgpLocaldbCommunityPath	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1.13	AsciiString	read-only	This attribute indicates the Community path attribute.
IP vrIpBgpLocaldbAsOriginatorId	1.3.6.1.4.1.562.2.4.1.100.6.21.8.10.1.14	IpAddress	read-only	This attribute is associated with the Route Reflector. It indicates the router-id of the originator in the local AS. A value of 0.0.0.0 indicates this attribute is not present in the learned IBGP route or if this Bgp instance is not a Route Reflector.
vrIpBgpLocaldbRrClusterListTable	1.3.6.1.4.1.562.2.4.1.100.6.21.8.797		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This attribute indicates a sequence of cluster-ids that the route has traversed. A blank list indicates this attribute is not present in the learned IBGP route or if this Bgp instance is not a Route Reflector.
vrIpBgpLocaldbRrClusterListEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.8.797.1		not-accessible	An entry in the vrIpBgpLocaldbRrClusterListTable.
IP vrIpBgpLocaldbRrClusterListValue	1.3.6.1.4.1.562.2.4.1.100.6.21.8.797.1.1	IpAddress	read-only	This variable represents both the value and the index for the vrIpBgpLocaldbRrClusterListTable.
vrIpBgpOutdb	1.3.6.1.4.1.562.2.4.1.100.6.21.9
vrIpBgpOutdbRowStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.9.1		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This entry controls the addition and deletion of vrIpBgpOutdb components.
vrIpBgpOutdbRowStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.9.1.1		not-accessible	A single entry in the table represents a single vrIpBgpOutdb component.
ROW vrIpBgpOutdbRowStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.9.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of vrIpBgpOutdb components. These components cannot be added nor deleted.
STR vrIpBgpOutdbComponentName	1.3.6.1.4.1.562.2.4.1.100.6.21.9.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO vrIpBgpOutdbStorageType	1.3.6.1.4.1.562.2.4.1.100.6.21.9.1.1.4	StorageType	read-only	This variable represents the storage type value for the vrIpBgpOutdb tables.
IP vrIpBgpOutdbPrefixIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.9.1.1.10	IpAddress	not-accessible	This variable represents an index for the vrIpBgpOutdb tables.
I32 vrIpBgpOutdbLengthIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.9.1.1.11	Integer32	not-accessible	This variable represents an index for the vrIpBgpOutdb tables.
IP vrIpBgpOutdbPeerIndex	1.3.6.1.4.1.562.2.4.1.100.6.21.9.1.1.12	IpAddress	not-accessible	This variable represents an index for the vrIpBgpOutdb tables.
vrIpBgpOutdbOperTable	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This group contains all the operational attributes of the OutdbEntry component.
vrIpBgpOutdbOperEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1		not-accessible	An entry in the vrIpBgpOutdbOperTable.
INT vrIpBgpOutdbOrigin	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1.4	INTEGER	read-only	This attribute indicates the ultimate origin of the path information. A value of incomplete means this information is not available.
IP vrIpBgpOutdbNextHop	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1.5	IpAddress	read-only	This attribute indicates the IP address of the border router that should be used as the next hop for the destination network.
U32 vrIpBgpOutdbLocalPreference	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1.6	Unsigned32	read-only	This attribute indicates this Bgp instance's degree of preference for an advertised route. A higher value indicates a more preferred route.
U32 vrIpBgpOutdbMultiExitDiscriminator	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1.7	Unsigned32	read-only	This attribute indicates a metric used to discriminate between multiple exit points to the same adjacent autonomous system. A lower value indicates a more preferred route.
INT vrIpBgpOutdbAtomicAggregate	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1.8	INTEGER	read-only	This attribute indicates whether or not the local system has selected a less specific route without selecting a more specific route.
U32 vrIpBgpOutdbAggregatorAs	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1.9	Unsigned32	read-only	This attribute indicates the AS number of the last BGP4 speaker that performed route aggregation. A value of zero (0) indicates the absence of this attribute.
IP vrIpBgpOutdbAggregatorAddr	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1.10	IpAddress	read-only	This attribute indicates the IP address of the last BGP4 speaker that performed route aggregation. A value of 0.0.0.0 indicates the absence of this attribute.
STR vrIpBgpOutdbAsPath	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1.11	AsciiString	read-only	This attribute indicates the sequence of AS path segments. The AS Path Attribute lists the ASs in reverse traversal order.
STR vrIpBgpOutdbUnknownAttributes	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1.12	AsciiString	read-only	This attribute indicates all the path attributes not understood by this Bgp component instance.
STR vrIpBgpOutdbCommunityPath	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1.13	AsciiString	read-only	This attribute indicates the Community path attribute.
IP vrIpBgpOutdbAsOriginatorId	1.3.6.1.4.1.562.2.4.1.100.6.21.9.10.1.14	IpAddress	read-only	This attribute is associated with the Route Reflector. It indicates the router-id of the originator of a route in the local AS. When the Route Reflector distributes a learned IBGP route to other IBGP speakers, the value of this attribute in the learned route is used if one is present; othewise, the Route Reflector's router-id is used. A value of 0.0.0.0 indicates this Bgp instance is not a Route Reflector.
vrIpBgpOutdbRrClusterListTable	1.3.6.1.4.1.562.2.4.1.100.6.21.9.799		not-accessible	* THIS TABLE CURRENTLY NOT IMPLEMENTED * This attribute indicates a sequence of cluster-ids that the route has traversed. When the Route Reflector redistributes a learned IBGP to other IBGP speakers, the cluster id of this Route Reflector is appended to the cluster list of the learned IBGP route. If this Bgp instance is not a Route Reflector, this attribute is blank.
vrIpBgpOutdbRrClusterListEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.9.799.1		not-accessible	An entry in the vrIpBgpOutdbRrClusterListTable.
IP vrIpBgpOutdbRrClusterListValue	1.3.6.1.4.1.562.2.4.1.100.6.21.9.799.1.1	IpAddress	read-only	This variable represents both the value and the index for the vrIpBgpOutdbRrClusterListTable.
vrIpBgpProvTable	1.3.6.1.4.1.562.2.4.1.100.6.21.100		not-accessible	This group contains the provisionable attributes for the Bgp component.
vrIpBgpProvEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.100.1		not-accessible	An entry in the vrIpBgpProvTable.
IP vrIpBgpBgpIdentifier	1.3.6.1.4.1.562.2.4.1.100.6.21.100.1.1	IpAddress	read-write	This attribute specifies the Bgp Identifier of this Bgp component instance. It is picked from the IP address space, and should follow the same rule as choosing an unique IP address for IpPort.
U32 vrIpBgpLocalAs	1.3.6.1.4.1.562.2.4.1.100.6.21.100.1.2	Unsigned32	read-write	This attribute specifies the autonomous system identifier for this Bgp component instance.
U32 vrIpBgpDefaultLocalPreference	1.3.6.1.4.1.562.2.4.1.100.6.21.100.1.3	Unsigned32	read-write	This attribute specifies this Bgp component instance's default degree of preference for routes. It can be overridden by the localPreference provisioned in ImportPolicy. A higher value indicates a more preferred route.
U32 vrIpBgpDefaultMultiExitDisc	1.3.6.1.4.1.562.2.4.1.100.6.21.100.1.4	Unsigned32	read-write	This attribute specifies this Bgp component instance's default metric to discriminate between multiple exit points to the same adjacent autonomous system. It can be overridden by the sendMultiExitDiscToEbgp provisioned in ExportPolicy. A lower value indicates a more preferred route.
U32 vrIpBgpRouteThrottleLimit	1.3.6.1.4.1.562.2.4.1.100.6.21.100.1.5	Unsigned32	read-write	This attribute specifies the maximum number of routes in the IP forwarding table this Bgp component instance will process at one time to decide if a route in the IP forwarding table should be exported to a peer. This limit is used for the throttling and is made configurable because the throttling requirements will be different under different network configurations. The default value is 250.
U32 vrIpBgpRouteThrottleInter	1.3.6.1.4.1.562.2.4.1.100.6.21.100.1.6	Unsigned32	read-write	This attribute specifies the interval in seconds, between the processing of the routes in the IP forwarding table to decide if a route in the IP forwarding table should be exported to a peer. This interval is used for the throttling and is made configurable because the throttling requirements will be different under different network configurations. The default value is 5 seconds.
INT vrIpBgpRouteReflector	1.3.6.1.4.1.562.2.4.1.100.6.21.100.1.7	INTEGER	read-write	This attribute specifies whether this Bgp instance is a Route Reflector. If the value of this attribute is true, Bgp redistributes routes it learns from an IBGP speaker to other IBGP speakers in the AS. The rule of redistribution depends on the peer type: 1) When a route is learned from a non-client peer, it is redistributed to all the client peers within the cluster. 2) When a route is learned from a client peer, it is redistributed to all the non-client peers and also to the client peers. If the value of this attribute is false, Bgp does not redistribute routes it learns from one IBGP speaker to other IBGP speakers in the AS.
IP vrIpBgpRouteReflectorCluster	1.3.6.1.4.1.562.2.4.1.100.6.21.100.1.8	IpAddress	read-write	This attribute identifies the cluster consisting of the Route Reflector and its peer clients. When routeReflector of Bgp is true, value of 0.0.0.0 or 255.255.255.255 is invalid; the default value of this attribute is same as bgpIdentifier. For redundancy, a cluster may have more than one Route Reflector; in this case, the value of this attribute of all the Route Reflectors in the same cluster should be same. The value of this attribute is ignored when routeReflector of Bgp is false
vrIpBgpOperTable	1.3.6.1.4.1.562.2.4.1.100.6.21.101		not-accessible	This group contains the operational attributes for the Bgp component.
vrIpBgpOperEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.101.1		not-accessible	An entry in the vrIpBgpOperTable.
C32 vrIpBgpTableVersion	1.3.6.1.4.1.562.2.4.1.100.6.21.101.1.2	Counter32	read-only	This attribute indicates the version of the BGP routing table. It is incremented every time the BGP routing table changes. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpInMsgs	1.3.6.1.4.1.562.2.4.1.100.6.21.101.1.3	Counter32	read-only	This attribute counts the total number of BGP messages received without error. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpInErrors	1.3.6.1.4.1.562.2.4.1.100.6.21.101.1.4	Counter32	read-only	This attribute counts the total number of BGP messages received from all peers that proved to be in error. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpInErrorMsgs	1.3.6.1.4.1.562.2.4.1.100.6.21.101.1.5	Counter32	read-only	This attribute counts the total number of BGP NOTIFICATION messages from all the peers. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpOutMsgs	1.3.6.1.4.1.562.2.4.1.100.6.21.101.1.6	Counter32	read-only	This attribute counts the total number of BGP messages sent to peers. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpOutDiscards	1.3.6.1.4.1.562.2.4.1.100.6.21.101.1.7	Counter32	read-only	This attribute counts the number of BGP messages that were locally generated but were not sent out due to resource limitations within a Bgp instance. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpOutErrorMsgs	1.3.6.1.4.1.562.2.4.1.100.6.21.101.1.8	Counter32	read-only	This attribute counts the BGP NOTIFICATION messages sent to the peers. This counter will wrap to zero once the value exceeds the maximum value.
C32 vrIpBgpIndbSize	1.3.6.1.4.1.562.2.4.1.100.6.21.101.1.9	Counter32	read-only	This attribute indicates the number of Bgp indb entries under this Bgp component instance.
vrIpBgpStateTable	1.3.6.1.4.1.562.2.4.1.100.6.21.102		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
vrIpBgpStateEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.102.1		not-accessible	An entry in the vrIpBgpStateTable.
INT vrIpBgpAdminState	1.3.6.1.4.1.562.2.4.1.100.6.21.102.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT vrIpBgpOperationalState	1.3.6.1.4.1.562.2.4.1.100.6.21.102.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT vrIpBgpUsageState	1.3.6.1.4.1.562.2.4.1.100.6.21.102.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
vrIpBgpAdminControlTable	1.3.6.1.4.1.562.2.4.1.100.6.21.103		not-accessible	This group includes the Administrative Control attribute. This attribute defines the current administrative state of this component.
vrIpBgpAdminControlEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.103.1		not-accessible	An entry in the vrIpBgpAdminControlTable.
INT vrIpBgpSnmpAdminStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.103.1.1	INTEGER	read-write	The desired state of the interface. The up state indicates the interface is operational and packet forwarding is allowed. The down state indicates the interface is not operational and packet forwarding is unavailable. The testing state indicates that no operational packets can be passed.
vrIpBgpOperStatusTable	1.3.6.1.4.1.562.2.4.1.100.6.21.106		not-accessible	This group includes the Operational Status attribute. This attribute defines the current operational state of this component.
vrIpBgpOperStatusEntry	1.3.6.1.4.1.562.2.4.1.100.6.21.106.1		not-accessible	An entry in the vrIpBgpOperStatusTable.
INT vrIpBgpSnmpOperStatus	1.3.6.1.4.1.562.2.4.1.100.6.21.106.1.1	INTEGER	read-only	The current state of the interface. The up state indicates the interface is operational and capable of forwarding packets. The down state indicates the interface is not operational, thus unable to forward packets. testing state indicates that no operational packets can be passed.
bgpMIB	1.3.6.1.4.1.562.2.4.2.141
bgpGroup	1.3.6.1.4.1.562.2.4.2.141.1
bgpGroupBE	1.3.6.1.4.1.562.2.4.2.141.1.5
bgpGroupBE01	1.3.6.1.4.1.562.2.4.2.141.1.5.2
bgpGroupBE01A	1.3.6.1.4.1.562.2.4.2.141.1.5.2.2
bgpCapabilities	1.3.6.1.4.1.562.2.4.2.141.3
bgpCapabilitiesBE	1.3.6.1.4.1.562.2.4.2.141.3.5
bgpCapabilitiesBE01	1.3.6.1.4.1.562.2.4.2.141.3.5.2
bgpCapabilitiesBE01A	1.3.6.1.4.1.562.2.4.2.141.3.5.2.2

RFC description

Border Gateway Protocol (BGP) management for Nortel Magellan Passport virtual routers with IP routing configuration.

Start monitoring Nortel Magellan Passport WAN switch (per-VR BGP) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Nortel-Magellan-Passport-BgpMIB

What Is Nortel-Magellan-Passport-BgpMIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description