NEXANS-BM-MIB

All MIBs › NEXANS-BM-MIB

Organization: Nexans Advanced Networking Solutions

Last Updated: 2014-01-29

Category: QoS

Description: Monitors bandwidth management and traffic shaping parameters on Nexans Advanced Networking Solutions equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is NEXANS-BM-MIB?

NEXANS-BM-MIB is a Nexans Advanced Networking Solutions proprietary MIB (built on NEXANS-MIB) reporting switch identity, hardware/firmware version, and security-event status. Its objects cover device description/type/product number/series/manufacture date, switch/management hardware version, management firmware version, port count, reboot count, temperature (and max-allowed), power-supply voltages (2.5V/3.3V), an unauthorized-IP-address object, security-fail/new-MAC-address objects, PoE input voltage/power, two alarm-state objects, and last-TFTP/last-SFP-event/last-internal-management-warning message strings. As a status/security MIB it lets an administrator watch temperature/power health and get alerted on unauthorized access attempts on a Nexans switch. It is deployed on Nexans Advanced Networking Solutions switching equipment. Engineers can download the NEXANS-BM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in NEXANS-BM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nexans Advanced Networking Solutions switching equipment

Monitoring Examples

An administrator checks infoUnauthIpAddr and infoSecurityFailMacAddr to investigate an unauthorized access attempt on a Nexans switch.

What Can Be Monitored

temperature/power health and unauthorized-access security events

Imported Objects

From NEXANS-MIB

nexansANS

OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString
MacAddress

How to Use in IPNetwork Monitor

Example using infoNoOfReboots OID:

Select a Nexans Advanced Networking Solutions switching equipment as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type infoNoOfReboots into the Find box to locate it in the OID tree, then select it and click OK. The number of reboots since the manufacturing date. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
bmSwitchMIB	1.3.6.1.4.1.266.20			MIB for Nexans switches
bmTraps	1.3.6.1.4.1.266.20.0
NTF switchTemperatureFailure	1.3.6.1.4.1.266.20.0.1			A TemperatureFailure signifies that the switch hardware has detected under- or overtemperature condition.
NTF portLinkChange	1.3.6.1.4.1.266.20.0.2			The trap is sent whenever the link state of a port changes from link-up to link-down or from link-down to link-up
NTF portNewMacAddress	1.3.6.1.4.1.266.20.0.3			A new source MAC address has been detected on a switch port. This trap is only send for ports which have port-security enabled with the setting autoAllowOneMacAddr, autoAllowTwoMacAddr or autoAllowThreeMacAddr.
NTF portSecurityFailure	1.3.6.1.4.1.266.20.0.4			An unauthorized source MAC address has accessed a port which has port-security enabled.
NTF portErrorCountFailure	1.3.6.1.4.1.266.20.0.5			The port error counter has incremented by 2 or more within a timewindow of two seconds. An counter increment by 1 ist not reported because single increments often may result because of link-changes.
NTF switchMgmtAuthFailure	1.3.6.1.4.1.266.20.0.6			A station has tried to access the switch management with a wrong authentication. This includes wrong user/password for telnet, wrong community for SNMP read/write and wrong accessrights in the accesslist.
NTF radiusMgmtAuthReject	1.3.6.1.4.1.266.20.0.7			A station has tried to access the switch management with radius authentication enabled and the radius server has rejected the request.
NTF radiusPortSecurityReject	1.3.6.1.4.1.266.20.0.8			A station has tried to access the switch with radius port security authentication enabled and the radius server has rejected the request.
NTF portLoopBcastFailure	1.3.6.1.4.1.266.20.0.9			The port broadcast/multicast counter has incremented by 25 packets/second for more then 10 successive seconds. Excessive multicast or broadcast packets may result in case of a loop between two port of the switch.
NTF switchPoeVoltageFailure	1.3.6.1.4.1.266.20.0.10			The switch has detected a PoE over- or undervoltage conditions.
NTF switchPoeOverloadFailure	1.3.6.1.4.1.266.20.0.11			The switch has detected a overload for the PoE power supply.
NTF portPoeOverloadFailure	1.3.6.1.4.1.266.20.0.12			The switch has detected a PoE overload condition at the port.
NTF portActiveLoopDetectionFailure	1.3.6.1.4.1.266.20.0.13			The active loop protection has disabled the port.
NTF switchIndustrialAlarmM1	1.3.6.1.4.1.266.20.0.14			The alarm state of the industrial alarm output M1 has changed.
NTF switchIndustrialAlarmM2	1.3.6.1.4.1.266.20.0.15			The alarm state of the industrial alarm output M2 has changed.
NTF switchInternalVoltageFailure	1.3.6.1.4.1.266.20.0.16			The switch has detected a internal over- or undervoltage conditions.
NTF tftpMessage	1.3.6.1.4.1.266.20.0.17			An successful or failed TFTP transfer has been occured. This does not include TFTP transfers executed from Nexan Manager.
NTF sfpEvent	1.3.6.1.4.1.266.20.0.18			The switch has detected one of the following SFP events: - a SFP module has been inserted - a SFP module has been removed - the optical receive power has fallen below the configured threshold - the optical transmit power has fallen below the configured threshold - the laser bias current has exceeded the configured threshold In the case of a threshold event, the trap will only send out every five minutes.
NTF clientRemoved	1.3.6.1.4.1.266.20.0.19			The client on this port has been removed because the link down time has exceeded the configured 'Link Down Timeout'.
NTF internalMgmtWarning	1.3.6.1.4.1.266.20.0.20			An internal management warning has been detected. Please consult Nexans for further informations regarding the reported warning code.
NTF switchFunctionInputAlarm	1.3.6.1.4.1.266.20.0.21			The state of the function input has changed.
NTF switchConfigurationChanged	1.3.6.1.4.1.266.20.0.22			The configuration of the switch has been changed.
NTF portErrorDisabled	1.3.6.1.4.1.266.20.0.23			The port has been error disabled.
bmSwitchInfo	1.3.6.1.4.1.266.20.1
STR infoDescr	1.3.6.1.4.1.266.20.1.1	DisplayString	read-only	The ordering description of the switch
I32 infoType	1.3.6.1.4.1.266.20.1.2	Integer32	read-only	The infoType indentifies the product familie of this switch. Refer to NEXANS-MIB for the currently defined families
STR infoProductNo	1.3.6.1.4.1.266.20.1.3	DisplayString	read-only	The product number of the switch (8830xxxx)
STR infoSerie	1.3.6.1.4.1.266.20.1.4	DisplayString	read-only	The production series of the switch
STR infoSeriesNo	1.3.6.1.4.1.266.20.1.5	DisplayString	read-only	The production number of the switch
STR infoManufactureDate	1.3.6.1.4.1.266.20.1.6	DisplayString	read-only	The manufacturing date of the switch. The display format is dd.mm.jjjj
STR infoSwitchHardwareVersion	1.3.6.1.4.1.266.20.1.7	DisplayString	read-only	The hardware version of the base switch.
STR infoMgmtHardwareVersion	1.3.6.1.4.1.266.20.1.8	DisplayString	read-only	The hardware version of the plug-in management module.
STR infoMgmtFirmwareVersion	1.3.6.1.4.1.266.20.1.9	DisplayString	read-only	The firmware version of the management module.
I32 infoNoOfPorts	1.3.6.1.4.1.266.20.1.10	Integer32	read-only	The number of switching ports within the system. This includes all user and uplink ports.
C32 infoNoOfRebootsEx	1.3.6.1.4.1.266.20.1.11	Counter32	read-only	The number of reboots since the manufacturing date. This counter can't be cleared by any admin command.
I32 infoTemperature	1.3.6.1.4.1.266.20.1.12	Integer32	read-only	The case temperature in degree Celsius of the switch.
I32 infoTemperatureMaxAllowed	1.3.6.1.4.1.266.20.1.13	Integer32	read-only	The upper limit of the allowed temperature range in degree Celsius. If the current temperature indicated by infoTemperature exceeds infoTemperatureMaxAllowed, the switch sends an switchOverTemperature alarm trap.
I32 infoPowerVoltage2500	1.3.6.1.4.1.266.20.1.14	Integer32	read-only	The 2.5 volt supply voltage in millivolts. The allowed range is 2300...2700 millivolts.
I32 infoPowerVoltage3300	1.3.6.1.4.1.266.20.1.15	Integer32	read-only	The 3.3 volt supply voltage in millivolts. The allowed range is 3100...3500 millivolts.
IP infoUnauthIpAddr	1.3.6.1.4.1.266.20.1.16	IpAddress	read-only	The source IP address of the station which generated the last authentication failure. The infoUnauthAddr is also reported in the switchMgmtAuthFailure alarm trap.
STR infoSecurityFailMacAddr	1.3.6.1.4.1.266.20.1.17	DisplayString	read-only	The source MAC address of the station which has generated a the last port security failure. The infoSecurityFailMacAddr is also reported in the portSecurityFailure alarm trap.
STR infoNewMacAddr	1.3.6.1.4.1.266.20.1.18	DisplayString	read-only	The last new source MAC address seen on a port witch has portsecurity enabled. The infoNewMacAddr is also reported in the newMacAddress trap.
I32 infoPoeInputVoltage	1.3.6.1.4.1.266.20.1.19	Integer32	read-only	The current PoE input voltage delivered from the power supply.
I32 infoPoeInputPower	1.3.6.1.4.1.266.20.1.20	Integer32	read-only	The current PoE input power delivered from the power supply.
INT infoAlarmStateM1	1.3.6.1.4.1.266.20.1.21	INTEGER	read-only	The current state of the industrial alarm output M1.
INT infoAlarmStateM2	1.3.6.1.4.1.266.20.1.22	INTEGER	read-only	The current state of the industrial alarm output M2.
STR infoLastTftpMessage	1.3.6.1.4.1.266.20.1.23	DisplayString	accessible-for-notify	The message of the last successful or failed TFTP transfer. This does not include TFTP transfers executed from Device Manager.
STR infoLastSfpEventMessage	1.3.6.1.4.1.266.20.1.24	DisplayString	accessible-for-notify	The last event message from one of the available SFP modules.
STR infoLastInternalMgmtWarning	1.3.6.1.4.1.266.20.1.25	DisplayString	accessible-for-notify	The last internal management warning message.
INT infoFunctionInputStateF1	1.3.6.1.4.1.266.20.1.26	INTEGER	read-only	The current state of the function input F1.
C32 infoTotalConfigChanges	1.3.6.1.4.1.266.20.1.27	Counter32	read-only	The number of total configurations changes.
bmSwitchAdmin	1.3.6.1.4.1.266.20.2
INT adminReset	1.3.6.1.4.1.266.20.2.1	INTEGER	read-write	Writing this object causes the switch to perform a reset operation. The following reset types are supported. Set Values: resetCounters(2) This action resets all error and statistic counters to zero. This actions will NOT reboot the switch. rebootSwitch(3) This action resets switch and management. All counters, timers and other volatile data are reset to there power-up values stored in flash. This actions will reboot the switch. rebootToFactoryDefaults(4) This action resets switch and management. All volatile and nonvolatile data are reset to there power-up or factory default values. This actions will reboot the switch. renewIpAndVlanParameter(5) This action reinitializes the IP and VLAN module of the switch so that the actually set IP and VLAN parameters will take affect. This actions will NOT reboot the switch. Get values: resetIdle(1) Reading this object will allways return resetIdle(1).
INT adminAgentDhcp	1.3.6.1.4.1.266.20.2.2	INTEGER	read-write	If set to enable(1), the switch tries to get his IP parameter via DHCP. If set to disable(2), the switch uses the IP parameters defined with adminIpAddress, adminDefRouterIpAddress and adminNetmask. Changes of this value will take affect after the next switch reboot or after setting adminReset to renewIpAndVlanParameter(5).
IP adminAgentIpAddress	1.3.6.1.4.1.266.20.2.3	IpAddress	read-write	The IP address of the switch agent's ethernet interface. If the value of adminDHCP is enable(1) this value is read-only. Changes of this value will take affect after the next switch reboot or after setting adminReset to renewIpAndVlanParameter(5).
MAC adminAgentPhysAddress	1.3.6.1.4.1.266.20.2.4	MacAddress	read-only	The Ethernet MAC address of the switch agent.
IP adminAgentDefRouterIpAddress	1.3.6.1.4.1.266.20.2.5	IpAddress	read-write	The IP address of the default Router. If the value of adminDHCP is enable(1) this value is read-only. Changes of this value will take affect after the next switch reboot or after setting adminReset to renewIpAndVlanParameter(5).
IP adminAgentNetmask	1.3.6.1.4.1.266.20.2.6	IpAddress	read-write	The IP Netmask of the connected network. If the value of adminDHCP is enable(1) this value is read-only. Changes of this value will take affect after the next switch reboot or after setting adminReset to renewIpAndVlanParameter(5).
IP adminAgentDhcpServerIpAddress	1.3.6.1.4.1.266.20.2.7	IpAddress	read-only	The IP address of the last used DHCP server.
I32 adminAgentVlanId	1.3.6.1.4.1.266.20.2.8	Integer32	read-write	The VLAN-ID assigned to the agent. Changes of this value will take affect after the next switch reboot or after setting adminReset to renewIpAndVlanParameter(5).
I32 adminAgentPrioValue	1.3.6.1.4.1.266.20.2.9	Integer32	read-write	The IEEE802.1Q priority value and queue assigned to all frames transmitted by the agent. The definition between value, service class and queue are as follows: 0=Best Effort (queue=0), 1=Background (queue=0), 2=Reserved (queue=1), 3=Excellent Effort (queue=1), 4=Controlled Load (queue=2), 5=Video (queue=2), 6=Voice (queue=3), 7=Network Control (queue=3)
I32 adminAddrAgingTimeMinutes	1.3.6.1.4.1.266.20.2.10	Integer32	read-write	The timeout period in minutes for aging out dynamically learned MAC addresses . The allowed range is 1 minute to 68 minutes.
INT adminSwitchPortMirror	1.3.6.1.4.1.266.20.2.11	INTEGER	read-write	If set to enable(1), the switch doesn't use address learning. This affects that any received packet will be forwarded to all ports of the particular VLAN. The switch acts like a hub within each VLAN.
INT adminMgmtAccessList	1.3.6.1.4.1.266.20.2.12	INTEGER	read-write	If set to enableForNexManAccess(2) or enableForAllAccess(3), the switch only accepts read or write requests from IP addresses which are listed in the management accesslist.
I32 adminSwitchPoEPowerLimit	1.3.6.1.4.1.266.20.2.13	Integer32	read-write	The limit for the POE input power from the power supply in VA. If the current power exceeds this value a overload conditions occurs and the inline power for the highest port number will be switched off.
INT adminSwitchVlanTableMode	1.3.6.1.4.1.266.20.2.14	INTEGER	read-write	If set to staticMode(1) or staticModeVlans64(3) any existing VLAN table entry must be removed manually by management. With staticMode(1) total 16 VLAN-ID's and with staticModeVlans64(3) total 64 VLAN-ID's are supported. If set to dynamicMode(2) all unused VLAN-ID's are removed automatically by the switch. This means, that all VLAN-ID's not assigned to a port Default-VLAND or to the Unsecure-VLAN will be removed.
I32 adminUnsecureVlanId	1.3.6.1.4.1.266.20.2.15	Integer32	read-write	The VLAN-ID of the unsecure VLAN
I32 adminDot1xAuthFailureVlanId	1.3.6.1.4.1.266.20.2.16	Integer32	read-write	The VLAN-ID in the case of an IEEE802.1X authentication failure. Setting the VLAN-ID to 0 disables the authentication failure VLAN.
INT adminTftpAccess	1.3.6.1.4.1.266.20.2.17	INTEGER	read-write	If 'TFTP authentication via SNMP' is disabled, this value is allways tftpAccessDisable(1). If 'TFTP authentication via SNMP' is read/only or read/write, an this object is read, the value is tftpAccessReadOnly(2) and the agent allowes a single TFTP read access of the switch configuration. If 'TFTP authentication via SNMP' is read/write, this value can be set to tftpAccessReadWrite(3) and the agent allowes a single TFTP read or write access to the configuration or a single firmware upgrade. After finishing the TFTP transfer, this value will return to ftpAccessDisable(1) automatically. Note: If the 'NexMan authentication mode' is set to 'none', TFTP read and write access is allways allowed.
INT adminSnmpMacTableMode	1.3.6.1.4.1.266.20.2.18	INTEGER	read-write	If set to listAllPorts(1) the BRIDGE-MIBs dot1dTpFdbTable lits MAC address of all ports. If set to listUserPortsOnly(2) the BRIDGE-MIBs dot1dTpFdbTable lits only MAC addresses of user ports. MAC addresses of uplink/downlink ports are ignored.
INT adminAlarmM1	1.3.6.1.4.1.266.20.2.19	INTEGER	read-write	The current setup of the industrial alarm output M1.
INT adminAlarmM2	1.3.6.1.4.1.266.20.2.20	INTEGER	read-write	The current setup of the industrial alarm output M2.
INT adminMemoryCardMode	1.3.6.1.4.1.266.20.2.21	INTEGER	read-write	If set to mcDisabled(2), the memory card is disabled but may be re-enabled later by writing mcEnabled(1). If set to mcPermanentDisabled(3), the memory card is disabled permanently and can't be re-enabled by management or any kind of hardware reset.
STR adminAlarmNameM1	1.3.6.1.4.1.266.20.2.22	DisplayString	read-write	An administratively assigned name for alarm output M1. The configured name will be send as part of alarm message switchIndustrialAlarmM1.
STR adminAlarmNameM2	1.3.6.1.4.1.266.20.2.23	DisplayString	read-write	An administratively assigned name for alarm output M1. The configured name will be send as part of alarm message switchIndustrialAlarmM2.
STR adminFunctionInputNameF1	1.3.6.1.4.1.266.20.2.24	DisplayString	read-write	An administratively assigned name for function input F1. The configured name will be send as part of alarm message switchFunctionInputAlarm.
INT adminLedGlobalMode	1.3.6.1.4.1.266.20.2.25	INTEGER	read-write	Set the global mode for all front side LEDs.
bmSwitchPort	1.3.6.1.4.1.266.20.3
bmSwitchPortTable	1.3.6.1.4.1.266.20.3.1		not-accessible	A list of port entries for the switch. The number of entries is defined by ifNumber.
bmSwitchPortEntry	1.3.6.1.4.1.266.20.3.1.1		not-accessible	A port entry in the table containing information about a port in the switch.
I32 portIndex	1.3.6.1.4.1.266.20.3.1.1.1	Integer32	read-only	A unique value for each port. Its value ranges between 1 and the value of ifNumber. The port identified by a particular value of this index is the same port as identified by the same value of ifIndex.
STR portDescr	1.3.6.1.4.1.266.20.3.1.1.2	DisplayString	read-only	A textual string containing information about the interface. Same as ifDescr.
STR portName	1.3.6.1.4.1.266.20.3.1.1.3	DisplayString	read-write	An administratively assigned name for this port.
INT portAdminState	1.3.6.1.4.1.266.20.3.1.1.4	INTEGER	read-write	A value indicating the current state of the port. A SET to this object enables (2) or disables (3) the port. The possible values returned by GET are: allwaysEnable(1) The port is always enabled (usually the uplink port). enable(2) The port is active to transmit or receive data. disable(3) The port is inactive and unable to transmit or receive data. securityDisable(4) The port has been automatically disabled because of security violation. loopDisable(5) The port has been automatically disabled because of the active loop protection. bpduDisable(6) The port has been automatically disabled because a BPDU has been received on a Spanning Tree disabled port. udldDisable(7) The port has been automatically disabled because of the UDLD function. linkFlapDisable(8) The port has been automatically disabled because of the link flap protection. errorCountDisable(9) The port has been automatically disabled because of the error counter incrementation detection. sfpErrorDisable(10) The port has been automatically disabled because of wromg SFP inserted or SFP malfunction. redundanyLoopDisable(11) The port has been automatically disabled because of loop detection while spannung tree was enabled
INT portSpeedDuplexSetup	1.3.6.1.4.1.266.20.3.1.1.5	INTEGER	read-write	A value indicating the current speed and duplex link setup. Independent of portSpeedDuplexSetup the port may be disabled by portAdminState.
INT portLinkState	1.3.6.1.4.1.266.20.3.1.1.6	INTEGER	read-only	A value indicating the current link state.
C32 portErrorCounter	1.3.6.1.4.1.266.20.3.1.1.7	Counter32	read-only	Errors are usually caused by a FDX/HDX mismatch between the switch port and the connected port. If the switch detects a incrementation of this counter, he will send a portErrorCountFailure trap. The counted errors are depending on the switch type. For BM-A, BM+ and Access Switches: - Received packets with bad CRC, - Received packets with bad alignment, - Late collisions (only valid if Link State is 10HDX or 100HDX). For old BM Switches: - Received packets with bad CRC
INT portRemoteFault	1.3.6.1.4.1.266.20.3.1.1.8	INTEGER	read-write	If portRemoteFault is enabled for this port, the port transmitter will be only enabled if the port receiver has a valid link (portLinkState must not be down).
I32 portDefaultVlanId	1.3.6.1.4.1.266.20.3.1.1.9	Integer32	read-write	The Default-VLAN-ID assigned to this port. This Default-VLAN-ID has differnt affects depending on received or transmited frames: a) All received frames, which have no VLAN-tag, will be assigned to the Default-VLAN-ID. b) All transmited frames, which belong to the Default-VLAN, are send without a VLAN-tag. If portTrunkingMode is set to dot1qTagging, all frames are transmited with a VLAN-tag, except frames which belong to the Default-VLAN-ID. Changes of this value will take affect after the next switch reboot or after setting adminReset to renewIpAndVlanParameter(5). Setting this value to 0 for a port with dot1qTagging will disable the Default-VLAN. This means, that all frames are send tagged.
INT portTrunkingMode	1.3.6.1.4.1.266.20.3.1.1.10	INTEGER	read-write	If portTrunkingMode is set to dot1qTagging, all frames are transmited with a VLAN-tag, except frames which belong to portNativeVlanId. If portTrunkingMode is set to enableWithoutTagging, all frames are transmited without a VLAN-tag. Changes of this value will take affect after the next switch reboot or after setting adminReset to renewIpAndVlanParameter(5).
I32 portDot1qDefaultPrioValue	1.3.6.1.4.1.266.20.3.1.1.11	Integer32	read-write	The default IEEE802.1Q priority and queue assigned all frames received on this port, for which no other priorisation applies (IEEE801.1q Tag or IPv4/IPv6). The definition between value, service class and queue are as follows: 0=Best Effort (queue=0), 1=Background (queue=0), 2=Reserved (queue=1), 3=Excellent Effort (queue=1), 4=Controlled Load (queue=2), 5=Video (queue=2), 6=Voice (queue=3), 7=Network Control (queue=3)
I32 portDefaultPrioQueue	1.3.6.1.4.1.266.20.3.1.1.12	Integer32	read-only	The default priority queue assigned all frames received on this port, for which no other priorisation applies (IEEE801.1q Tag or IPv4/IPv6). A value of 0 means the lowest priority level. A value of 3 means the highest priority level. To change this default queue use object portDot1qDefaultPrioValue.
INT portLEDGreen	1.3.6.1.4.1.266.20.3.1.1.13	INTEGER	read-write	The function of the green port LED. Only supported for user ports
INT portLEDYellow	1.3.6.1.4.1.266.20.3.1.1.14	INTEGER	read-write	The function of the yellow port LED. Only supported for user ports
INT portBandwidthLimitRxd	1.3.6.1.4.1.266.20.3.1.1.15	INTEGER	read-write	The bandwidth limiter for received packets. If set to disable(2) the limiter will be disabled.
INT portBandwidthLimitTxd	1.3.6.1.4.1.266.20.3.1.1.16	INTEGER	read-write	The bandwidth limiter for transmitted packets. If set to disable(2) the limiter will be disabled.
INT portSecurityAdminState	1.3.6.1.4.1.266.20.3.1.1.17	INTEGER	read-write	Enables the port security feature for that port. A value of notSupported(1) means, that port security ist not supported or disabled for that port (i.e. uplink port). The command renew(10) clears all learned MAC addresses and enables the port if it is disabled. See documentation for more details.
MAC portSecurityMacAddr1	1.3.6.1.4.1.266.20.3.1.1.18	MacAddress	read-write	The first MAC address used for port security. If portSecurityAdminState has the value disable(2), portSecurityManualSettingMacAddr(3) or vendorSettingMacAddr(12) then this object will be read-write. In any other mode this object will be read-only and shows the first automatically learned MAC addresses for that port.
MAC portSecurityMacAddr2	1.3.6.1.4.1.266.20.3.1.1.19	MacAddress	read-write	The second MAC address used for port security. If portSecurityAdminState has the value disable(2), portSecurityManualSettingMacAddr(3) or vendorSettingMacAddr(12) then this object will be read-write. In any other mode this object will be read-only and shows the second automatically learned MAC addresses for that port.
MAC portSecurityMacAddr3	1.3.6.1.4.1.266.20.3.1.1.20	MacAddress	read-write	The third MAC address used for port security. If portSecurityAdminState has the value disable(2), portSecurityManualSettingMacAddr(3) or vendorSettingMacAddr(12) then this object will be read-write. In any other mode this object will be read-only and shows the third automatically learned MAC addresses for that port.
INT portPoeAdminState	1.3.6.1.4.1.266.20.3.1.1.21	INTEGER	read-write	If no POE adapter is installed this object is read-only and will always report notSupported(1). The possible values are: notSupported(1): No adapter installed or not supported for that port (i.e. uplink port). off(2): Adapter installed but inline power for that port is switched off. forcedOn(3): Adapter installed and inline power is asserted permanently. In the case of an IEEE802.3af adapter this setting will disable the IEEE802.3af automatic detection. autoOn(4): This setting is only supported if a IEEE802.3af adapter is installed. The adapter automatically detects if the connected device is IEEE802.3af compliant and will assert the power if possible. overloadFail(5): Adapter installed but inline power for that port is automatically switched off because of a overload condition at that port.
I32 portPoeVoltage	1.3.6.1.4.1.266.20.3.1.1.22	Integer32	read-only	The current PoE output voltage at this port in volts.
I32 portPoeCurrent	1.3.6.1.4.1.266.20.3.1.1.23	Integer32	read-only	The current PoE output current at this port in milliampere.
I32 portPoePower	1.3.6.1.4.1.266.20.3.1.1.24	Integer32	read-only	The current PoE output power at this port in milliwatt. The output power is the product of portPoeVoltage and portPoeCurrent.
INT portSecurityForwardingState	1.3.6.1.4.1.266.20.3.1.1.25	INTEGER	read-only	The port security forwarding state of that port. See documentation for details.
I32 portPoePowerLimit	1.3.6.1.4.1.266.20.3.1.1.26	Integer32	read-write	The limit for the POE output power at this port in VA. If the current power exceeds this value a overload conditions occurs and the inline power for that port will be switched off.
INT portLimiterPacketType	1.3.6.1.4.1.266.20.3.1.1.27	INTEGER	read-write	The packet type for bandwidth limiter. If set to limitAllPacktes(2) then all packets are limited. If set to limitLoppBcastPackets(3) only flooted loop- and broadcast-pakets are limited.
INT portAcApSetup	1.3.6.1.4.1.266.20.3.1.1.28	INTEGER	read-write	If portAcApSetup is enabled, the switch will perform Autocrossover and Autopolarity for this port. This function should only be enabled if portSpeedDuplexSetup ist set to autoneg.
INT portLinkType	1.3.6.1.4.1.266.20.3.1.1.29	INTEGER	read-write	The link type of that port. If set to upDownlink(3) the portAdminState will be forced to enable.
I32 portVoiceVlanId	1.3.6.1.4.1.266.20.3.1.1.30	Integer32	read-write	The Voide-VLAN-ID assigned to this port. Packets of this Voice-VLAN are allway send with a VLAN-Tag, because IP-Phones normaly need a tagged VLAN. If portTrunkingMode is set to dot1qTagging, ALL frames are transmited with a VLAN-tag, except frames which belong to the Default-VLAN-ID. In this case the Voice-VLAN-ID has no effect. Changes of this value will take affect after the next switch reboot or after setting adminReset to renewIpAndVlanParameter(5). Setting this value to 0 will disable the Voice-VLAN.
INT portPrioDot1p	1.3.6.1.4.1.266.20.3.1.1.31	INTEGER	read-write	Defines whether port prioritisation for IEEE802.1p packets is enabled.
INT portPrioIp	1.3.6.1.4.1.266.20.3.1.1.32	INTEGER	read-write	Defines whether port prioritisation for IPv4/IPv6 packets is enabled.
bmSwitchVlan	1.3.6.1.4.1.266.20.4
bmSwitchVlanTable	1.3.6.1.4.1.266.20.4.1		not-accessible	A list of Virtual LAN instances.
bmSwitchVlanEntry	1.3.6.1.4.1.266.20.4.1.1		not-accessible	VLAN entry.
I32 vlanIndex	1.3.6.1.4.1.266.20.4.1.1.1	Integer32	read-only	A unique value for each VLAN entry. Its value ranges between 1 and 16.
I32 vlanId	1.3.6.1.4.1.266.20.4.1.1.2	Integer32	read-write	The VLAN-ID assigned to this entry. Only entries with a VLAN-ID greater then 0 are valid entries. Setting a valid VLAN-ID to 0 will disable that entry and also delete the vlanDescr To add a new VLAN-ID first set an valid or non valid entry to the desired VLAN-ID. In a second step you may set the vlanDescr. Only VLAN-ID's listed in the vlanTable are forwarded by the switch.
STR vlanDescr	1.3.6.1.4.1.266.20.4.1.1.3	DisplayString	read-write	A textual string containing information about the VLAN.
bmSwitchSfp	1.3.6.1.4.1.266.20.5
bmSwitchSfpTable	1.3.6.1.4.1.266.20.5.1		not-accessible	A list of SFP entries for the switch. The number of entries is defined by ifNumber.
bmSwitchSfpEntry	1.3.6.1.4.1.266.20.5.1.1		not-accessible	A SFP entry in the table containing information about a SFP in the switch.
I32 sfpPortIndex	1.3.6.1.4.1.266.20.5.1.1.1	Integer32	read-only	A unique value for each port. Its value ranges between 1 and the value of ifNumber. The port identified by a particular value of this index is the same port as identified by the same value of ifIndex.
INT sfpState	1.3.6.1.4.1.266.20.5.1.1.2	INTEGER	read-only	A value indicating the current state of the SFP module. The possible values returned are: notSupported(1) The port has no SFP slot. noSfpInserted(2) The port has a SFP slot but there is no valid SFP module inserted. validSfpNoDiagnostic(3) A valid SFP module is inserted but the module doesn't supports diagnostic values. validSfpWithDiagnostic(4) A valid SFP module which supports diagnostic is inserted.
STR sfpInfoVendorName	1.3.6.1.4.1.266.20.5.1.1.3	DisplayString	read-only	A textual string containing the vendor name of the SFP module.
STR sfpInfoPartNumber	1.3.6.1.4.1.266.20.5.1.1.4	DisplayString	read-only	A textual string containing the part number of the SFP module.
STR sfpInfoRevisionNumber	1.3.6.1.4.1.266.20.5.1.1.5	DisplayString	read-only	A textual string containing the revision number of the SFP module.
STR sfpInfoSerialNumber	1.3.6.1.4.1.266.20.5.1.1.6	DisplayString	read-only	A textual string containing the serial number of the SFP module.
STR sfpInfoDateCode	1.3.6.1.4.1.266.20.5.1.1.7	DisplayString	read-only	A textual string containing the date code of the SFP module.
STR sfpInfoBitRate	1.3.6.1.4.1.266.20.5.1.1.8	DisplayString	read-only	A textual string containing the bit rate of the SFP module. The unit is Mbit/s
STR sfpInfoWavelength	1.3.6.1.4.1.266.20.5.1.1.9	DisplayString	read-only	A textual string containing the wavelength of the SFP module. The unit is nm.
STR sfpInfoLength9um	1.3.6.1.4.1.266.20.5.1.1.10	DisplayString	read-only	A textual string containing the typically supported fiber length for 9um fiber cable. The unit is meters.
STR sfpInfoLength50um	1.3.6.1.4.1.266.20.5.1.1.11	DisplayString	read-only	A textual string containing the typically supported fiber length for 50um fiber cable. The unit is meters.
STR sfpInfoLength62um	1.3.6.1.4.1.266.20.5.1.1.12	DisplayString	read-only	A textual string containing the typically supported fiber length for 62.5um fiber cable. The unit is meters.
STR sfpInfoConnectorDescr	1.3.6.1.4.1.266.20.5.1.1.13	DisplayString	read-only	A textual string containing the connector description of the SFP module.
I32 sfpDiagTemperature	1.3.6.1.4.1.266.20.5.1.1.14	Integer32	read-only	The current temperature of the SFP module in degree celsius.
I32 sfpDiagSupplyVoltage	1.3.6.1.4.1.266.20.5.1.1.15	Integer32	read-only	The current supply voltage of the SFP module in millivolt.
I32 sfpDiagTxBiasCurrent	1.3.6.1.4.1.266.20.5.1.1.16	Integer32	read-only	The current transmitter bias current of the SFP module in milliampere.
I32 sfpDiagTxOutputPower	1.3.6.1.4.1.266.20.5.1.1.17	Integer32	read-only	The current transmitter output power of the SFP module in microwatt.
I32 sfpDiagTxOutputPowerDbm	1.3.6.1.4.1.266.20.5.1.1.18	Integer32	read-only	The current transmitter output power of the SFP module in dbm.
I32 sfpDiagRxIntputPower	1.3.6.1.4.1.266.20.5.1.1.19	Integer32	read-only	The current receiver input power of the SFP module in microwatt.
I32 sfpDiagRxInputPowerDbm	1.3.6.1.4.1.266.20.5.1.1.20	Integer32	read-only	The current receiver input power of the SFP module in dbm.
I32 sfpAlarmTxBiasCurrentUpperLimit	1.3.6.1.4.1.266.20.5.1.1.21	Integer32	read-write	The maximum allowed transmitter bias current in milliampere. If the current value indicated by sfpDiagTxBiasCurrent exceeds sfpAlarmTxBiasCurrentUpperLimit, the switch sends an sfpEvent alarm trap. If the value of this limit is 0 no alarm will be send.
I32 sfpAlarmTxOutputPowerLowerLimit	1.3.6.1.4.1.266.20.5.1.1.22	Integer32	read-write	The minimum required transmitter output power in microwatt. If the power value indicated by sfpDiagTxOutputPower falls below sfpAlarmTxOutputPowerLowerLimit, the switch sends an sfpEvent alarm trap. If the value of this limit is 0 no alarm will be send.
I32 sfpAlarmRxInputPowerLowerLimit	1.3.6.1.4.1.266.20.5.1.1.23	Integer32	read-write	The minimum required received input power in microwatt. If the power value indicated by sfpDiagRxInputPower falls below sfpAlarmRxInputPowerLowerLimit, the switch sends an sfpEvent alarm trap. If the value of this limit is 0 no alarm will be send.

RFC description

Nexans managed switch administration, port status, SFP monitoring, and alarm management.

Start monitoring Nexans Advanced Networking Solutions switching equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download NEXANS-BM-MIB