All MIBs › NETEXEC-MIB
Category: Network Management
Description: Monitors NetExec network execution and management platform operational parameters.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is NETEXEC-MIB?
NETEXEC-MIB appears tied to a telecom network element management platform, with object prefixes dsucsu and tyview suggesting a DSU/CSU or digital cross-connect style device family. It exposes a system table describing chassis slot/node identity, system type, software and hardware revision, and channel count, plus network configuration and DACS (Digital Access Cross-connect System) configuration tables. Its monitoring value centers on hardware and software identity/status: dsucsuSysSoftRev and dsucsuSysHardRev let an operator confirm firmware/hardware revisions per slot, dsucsuSysNumChan tracks channel capacity, and the tyviewSysTable/tyviewBroadcastTable likely provide a supervisory view of node status across the platform. As a telecom-oriented MIB it likely coexists with standard IETF interface and physical-layer MIBs, though no explicit dependency is stated in the module description. It is typically deployed in carrier or enterprise telecom equipment rooms managing DSU/CSU or digital cross-connect network elements. Engineers can download the NETEXEC-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in NETEXEC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- DSU/CSU network element
- digital access cross-connect system (DACS)
Monitoring Examples
An admin would poll dsucsuSysTable/dsucsuSysEntry indexed by dsucsuSysSlot and dsucsuSysNode to inventory each card's dsucsuSysName, dsucsuSysType, and dsucsuSysSoftRev/dsucsuSysHardRev, flagging any slot running an unexpected firmware revision. The dsucsuCfgNetTable/dsucsuCfgNetEntry would be checked against dsucsuCfgNetSlot to confirm network configuration is applied per slot, and dsucsuCfgDacsTable would reveal cross-connect mapping configuration. A slot reporting an unexpectedly low dsucsuSysNumChan could indicate a card fault or misconfiguration.
What Can Be Monitored
- per-slot software/hardware revision
- system/node identity
- channel count
- per-slot network configuration
- DACS cross-connect configuration
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| TimeTicks |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| internet | 1.3.6.1 | |||
| private | 1.3.6.1.4 | |||
| enterprises | 1.3.6.1.4.1 | |||
| tylink | 1.3.6.1.4.1.466 | |||
| netexec | 1.3.6.1.4.1.466.6 | |||
| dsucsu | 1.3.6.1.4.1.466.6.1 | |||
| NTF dsucsuTrap | 1.3.6.1.4.1.466.6.1.0.0 | A dsucsuTrap trap signifies that the sending node had its `dsucsuAlarmType` variable modified. | ||
| dsucsuSysTable | 1.3.6.1.4.1.466.6.1.1 | not-accessible | A list of system level attributes describing the addressed node. | |
| dsucsuSysEntry | 1.3.6.1.4.1.466.6.1.1.1 | not-accessible | System Object for a DSU/CSU | |
| INT dsucsuSysSlot | 1.3.6.1.4.1.466.6.1.1.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuSysNode | 1.3.6.1.4.1.466.6.1.1.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| STR dsucsuSysName | 1.3.6.1.4.1.466.6.1.1.1.3 | DisplayString | read-only | The unique name of the node accessed |
| INT dsucsuSysType | 1.3.6.1.4.1.466.6.1.1.1.4 | INTEGER | read-only | A desciption of the system model: ie. ONS400, FNS400, ONS1000X, BLACK BOX FT1-4 |
| STR dsucsuSysSoftRev | 1.3.6.1.4.1.466.6.1.1.1.5 | DisplayString | read-only | Displays the Software Revision of the accessed node. |
| STR dsucsuSysHardRev | 1.3.6.1.4.1.466.6.1.1.1.6 | DisplayString | read-only | Displays the Hardware Revision of the accessed node. |
| INT dsucsuSysNumChan | 1.3.6.1.4.1.466.6.1.1.1.7 | INTEGER | read-only | The number of channels that are installed on the node. |
| dsucsuCfgNetTable | 1.3.6.1.4.1.466.6.1.2 | not-accessible | Network Line Configuration | |
| dsucsuCfgNetEntry | 1.3.6.1.4.1.466.6.1.2.1 | not-accessible | Configuration Object for a DSU/CSU | |
| INT dsucsuCfgNetSlot | 1.3.6.1.4.1.466.6.1.2.1.1 | INTEGER | read-only | The NEST slot to which the TyLink card is attached. |
| INT dsucsuCfgNetNode | 1.3.6.1.4.1.466.6.1.2.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuCfgNetIndex | 1.3.6.1.4.1.466.6.1.2.1.3 | INTEGER | read-only | The network index. |
| INT dsucsuCfgNetInterface | 1.3.6.1.4.1.466.6.1.2.1.4 | INTEGER | read-write | The interface type for 3000N. For a T1 line, NETWORK or DSX-1 is valid. |
| INT dsucsuCfgNetType | 1.3.6.1.4.1.466.6.1.2.1.5 | INTEGER | read-write | The aggregate line type. |
| INT dsucsuCfgNetCoding | 1.3.6.1.4.1.466.6.1.2.1.6 | INTEGER | read-write | The encoding scheme for the line. For a T1 line, AMI and B8ZS are valid. For an E1 line, AMI and HDB3 are valid. |
| INT dsucsuCfgNetClockSource | 1.3.6.1.4.1.466.6.1.2.1.7 | INTEGER | read-write | The aggregate timing for the addressed node. |
| INT dsucsuCfgNetCsuEnable | 1.3.6.1.4.1.466.6.1.2.1.8 | INTEGER | read-write | Enable/Disable Internal CSU. |
| INT dsucsuCfgNetCsuLBO | 1.3.6.1.4.1.466.6.1.2.1.9 | INTEGER | read-write | The setting of the Line Buildout switch. Setting must be db_0 if network interface is DSX-1. |
| INT dsucsuCfgNetCsuDensity | 1.3.6.1.4.1.466.6.1.2.1.10 | INTEGER | read-write | The setting of the one stuffing option. Inserts a 1 into the 8th, 16th, or 64th bit position (depending on the selection) if the previous 7 bits were 0's. |
| INT dsucsuCfgNetRateMultiples | 1.3.6.1.4.1.466.6.1.2.1.11 | INTEGER | read-write | The channel rate multiples for each of the ports. |
| INT dsucsuCfgNetOutputPulse | 1.3.6.1.4.1.466.6.1.2.1.12 | INTEGER | read-write | The distance to the CSU in feet. |
| INT dsucsuCfgNetTs0 | 1.3.6.1.4.1.466.6.1.2.1.13 | INTEGER | read-write | The E1 Timeslot 0 value. |
| INT dsucsuCfgNetTs16 | 1.3.6.1.4.1.466.6.1.2.1.14 | INTEGER | read-write | The E1 Timeslot 16 value. Valid values are data and multiframe alignment. |
| dsucsuCfgDteChanTable | 1.3.6.1.4.1.466.6.1.4 | not-accessible | DTE Channel Configuration | |
| dsucsuCfgDteChanEntry | 1.3.6.1.4.1.466.6.1.4.1 | not-accessible | DTE Channel Configuration Object for a DSU/CSU | |
| INT dsucsuCfgDteChanSlot | 1.3.6.1.4.1.466.6.1.4.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuCfgDteChanNode | 1.3.6.1.4.1.466.6.1.4.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuCfgDteChanIndex | 1.3.6.1.4.1.466.6.1.4.1.3 | INTEGER | read-only | The channel index. |
| INT dsucsuCfgDteChanType | 1.3.6.1.4.1.466.6.1.4.1.4 | INTEGER | read-write | The Dte channel type. |
| INT dsucsuCfgDteChanRate | 1.3.6.1.4.1.466.6.1.4.1.5 | INTEGER | read-write | The Data rate in kilobits per second. The rate is dependent on the setting of the Aggregate DTE channel multiples. |
| INT dsucsuCfgDteChanEncoding | 1.3.6.1.4.1.466.6.1.4.1.6 | INTEGER | read-write | The Channel encoding. |
| INT dsucsuCfgDteChanStartDs0 | 1.3.6.1.4.1.466.6.1.4.1.7 | INTEGER | read-write | The starting DS0 for the addressed channel's data. |
| INT dsucsuCfgDteChanCtrlSignal | 1.3.6.1.4.1.466.6.1.4.1.8 | INTEGER | read-write | The control signal state. |
| INT dsucsuCfgDteChanTiming | 1.3.6.1.4.1.466.6.1.4.1.9 | INTEGER | read-write | The DTE channel Timing. |
| INT dsucsuCfgDteChanClockInvert | 1.3.6.1.4.1.466.6.1.4.1.10 | INTEGER | read-write | The DTE channel Clock Invert setting. |
| INT dsucsuCfgDteChanDataInvert | 1.3.6.1.4.1.466.6.1.4.1.11 | INTEGER | read-write | The DTE channel Data Invert setting. |
| dsucsuCfgFrmChanTable | 1.3.6.1.4.1.466.6.1.5 | not-accessible | Framed Channel Configuration | |
| dsucsuCfgFrmChanEntry | 1.3.6.1.4.1.466.6.1.5.1 | not-accessible | Framed Channel Configuration Object for a DSU/CSU | |
| INT dsucsuCfgFrmChanSlot | 1.3.6.1.4.1.466.6.1.5.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuCfgFrmChanNode | 1.3.6.1.4.1.466.6.1.5.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuCfgFrmChanIndex | 1.3.6.1.4.1.466.6.1.5.1.3 | INTEGER | read-only | The channel index. |
| INT dsucsuCfgFrmChanType | 1.3.6.1.4.1.466.6.1.5.1.4 | INTEGER | read-only | The framed channel type. |
| INT dsucsuCfgFrmChanNumDs0 | 1.3.6.1.4.1.466.6.1.5.1.5 | INTEGER | read-write | The number of DS0's on the network side. |
| INT dsucsuCfgFrmChanEncoding | 1.3.6.1.4.1.466.6.1.5.1.6 | INTEGER | read-write | The channel line code. |
| INT dsucsuCfgFrmChanStartDs0 | 1.3.6.1.4.1.466.6.1.5.1.7 | INTEGER | read-write | The starting DS0 on the network side. |
| INT dsucsuCfgFrmChanDteStartDs0 | 1.3.6.1.4.1.466.6.1.5.1.8 | INTEGER | read-write | The starting DS0 on the framed channel. |
| INT dsucsuCfgFrmChanMapping | 1.3.6.1.4.1.466.6.1.5.1.9 | INTEGER | read-write | The Framed channel Mapping. |
| INT dsucsuCfgFrmChanDs0Type | 1.3.6.1.4.1.466.6.1.5.1.10 | INTEGER | read-write | The Framed channel DS0 Type. |
| INT dsucsuCfgFrmChanFrameType | 1.3.6.1.4.1.466.6.1.5.1.11 | INTEGER | read-write | The Framed channel Frame Type. |
| INT dsucsuCfgFrmChanOutputPulse | 1.3.6.1.4.1.466.6.1.5.1.12 | INTEGER | read-write | The cabling distance from the PBX to the PBX channel port in feet. |
| INT dsucsuCfgFrmChanNetMapping | 1.3.6.1.4.1.466.6.1.5.1.13 | INTEGER | read-write | The Network Ds0 Mapping. |
| dsucsuConfigSupTable | 1.3.6.1.4.1.466.6.1.7 | not-accessible | Inband Supervisory Channel Configuration | |
| dsucsuConfigSupEntry | 1.3.6.1.4.1.466.6.1.7.1 | not-accessible | Inband Supervisory Configuration Object for a DSU/CSU | |
| INT dsucsuConfigSupSlot | 1.3.6.1.4.1.466.6.1.7.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuConfigSupNode | 1.3.6.1.4.1.466.6.1.7.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuConfigSupIndex | 1.3.6.1.4.1.466.6.1.7.1.3 | INTEGER | read-only | The Supervisory channel index. Index 1 refers to supervisory channel A. Index 2 refers to supervisory channel B. |
| INT dsucsuConfigSupDs0 | 1.3.6.1.4.1.466.6.1.7.1.4 | INTEGER | read-write | The DS0 to place the Supervisory channel in. |
| dsucsuCfgSupAuxTable | 1.3.6.1.4.1.466.6.1.8 | not-accessible | Auxillary Supervisory Channel Configuration | |
| dsucsuCfgSupAuxEntry | 1.3.6.1.4.1.466.6.1.8.1 | not-accessible | Auxilary Supervisory Configuration Object for a DSU/CSU | |
| INT dsucsuCfgSupAuxSlot | 1.3.6.1.4.1.466.6.1.8.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuCfgSupAuxNode | 1.3.6.1.4.1.466.6.1.8.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuCfgSupAuxIndex | 1.3.6.1.4.1.466.6.1.8.1.3 | INTEGER | read-only | Auxillary Supervisory Channel Configuration Index Index 1 refers to FDL supervisory on PORT 1. Index 2 refers to FDL supervisory on PORT 2. |
| INT dsucsuCfgSupAuxFdl | 1.3.6.1.4.1.466.6.1.8.1.4 | INTEGER | read-write | Places the supervisory link bits within the Facility Data Link bits of the Extended Superframe. |
| dsucsuActvConfTable | 1.3.6.1.4.1.466.6.1.9 | not-accessible | Activate a stored configuration on the selected node. | |
| dsucsuActvConfEntry | 1.3.6.1.4.1.466.6.1.9.1 | not-accessible | An activate configuration entry. | |
| INT dsucsuActvConfSlot | 1.3.6.1.4.1.466.6.1.9.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuActvConfNode | 1.3.6.1.4.1.466.6.1.9.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuActvConfIndex | 1.3.6.1.4.1.466.6.1.9.1.3 | INTEGER | write-only | Activate one of the four stored configurations. |
| dsucsuEventDesTable | 1.3.6.1.4.1.466.6.1.10 | not-accessible | Table of event destinations. Events or alarms detected by a node can be reported to up to two destinations. The operator can set or clear either or both of these destinations via this Table. | |
| dsucsuEventDesEntry | 1.3.6.1.4.1.466.6.1.10.1 | not-accessible | Entry in the table of event destinations. | |
| INT dsucsuEventDesSlot | 1.3.6.1.4.1.466.6.1.10.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuEventDesNode | 1.3.6.1.4.1.466.6.1.10.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| STR dsucsuEventNameIndx | 1.3.6.1.4.1.466.6.1.10.1.3 | DisplayString | read-only | The unique name of the node accessed. |
| STR dsucsuEventDesName1 | 1.3.6.1.4.1.466.6.1.10.1.4 | DisplayString | read-write | The name of the node/PC where the alarms will be sent to. |
| STR dsucsuEventDesName2 | 1.3.6.1.4.1.466.6.1.10.1.5 | DisplayString | read-write | The name of the alternate node/PC where the alarms will be sent to. |
| INT dsucsuEventClrDest | 1.3.6.1.4.1.466.6.1.10.1.6 | INTEGER | write-only | Clears the destination(s) for the reporting of alarms. |
| dsucsuCfgMaintTable | 1.3.6.1.4.1.466.6.1.11 | not-accessible | Maint. Port Configuration | |
| dsucsuCfgMaintEntry | 1.3.6.1.4.1.466.6.1.11.1 | not-accessible | Maint. Port Configuration Object | |
| INT dsucsuCfgMaintSlot | 1.3.6.1.4.1.466.6.1.11.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuCfgMaintNode | 1.3.6.1.4.1.466.6.1.11.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuCfgMaintChanType | 1.3.6.1.4.1.466.6.1.11.1.3 | INTEGER | read-write | The type of data passed over the Maint. port. |
| INT dsucsuCfgMaintFlowCtrl | 1.3.6.1.4.1.466.6.1.11.1.4 | INTEGER | read-write | Flow Control for the Maint. port. |
| INT dsucsuCfgMaintStopBits | 1.3.6.1.4.1.466.6.1.11.1.5 | INTEGER | read-write | Number of Stopbits for the Maint. port. |
| INT dsucsuCfgMaintParity | 1.3.6.1.4.1.466.6.1.11.1.6 | INTEGER | read-write | Parity for the Maint. port. |
| INT dsucsuCfgMaintDataBits | 1.3.6.1.4.1.466.6.1.11.1.7 | INTEGER | read-write | Databits for the Maint. port. |
| INT dsucsuCfgMaintBaud | 1.3.6.1.4.1.466.6.1.11.1.8 | INTEGER | read-write | Baud rate for the Maint. port. |
| dsucsuCfgCommTable | 1.3.6.1.4.1.466.6.1.12 | not-accessible | Communication Port Configuration | |
| dsucsuCfgCommEntry | 1.3.6.1.4.1.466.6.1.12.1 | not-accessible | Communication Port Configuration Object | |
| INT dsucsuCfgCommSlot | 1.3.6.1.4.1.466.6.1.12.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuCfgCommNode | 1.3.6.1.4.1.466.6.1.12.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuCfgCommChanType | 1.3.6.1.4.1.466.6.1.12.1.3 | INTEGER | read-write | The type of data passed over the Communication port. |
| INT dsucsuCfgCommFlowCtrl | 1.3.6.1.4.1.466.6.1.12.1.4 | INTEGER | read-write | Flow Control for the Communication port. |
| INT dsucsuCfgCommStopBits | 1.3.6.1.4.1.466.6.1.12.1.5 | INTEGER | read-write | Number of Stopbits for the Communication port. |
| INT dsucsuCfgCommParity | 1.3.6.1.4.1.466.6.1.12.1.6 | INTEGER | read-write | Parity for the Communication port. |
| INT dsucsuCfgCommDataBits | 1.3.6.1.4.1.466.6.1.12.1.7 | INTEGER | read-write | Databits for the Communication port. |
| INT dsucsuCfgCommBaud | 1.3.6.1.4.1.466.6.1.12.1.8 | INTEGER | read-write | Baud rate for the Communication port. |
| dsucsuCfgBrdTable | 1.3.6.1.4.1.466.6.1.13 | not-accessible | Network timing for 3000N board. | |
| dsucsuCfgBrdEntry | 1.3.6.1.4.1.466.6.1.13.1 | not-accessible | Board Timing Configuration Object. | |
| INT dsucsuCfgBrdSlot | 1.3.6.1.4.1.466.6.1.13.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuCfgBrdNode | 1.3.6.1.4.1.466.6.1.13.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuCfgBrdTiming | 1.3.6.1.4.1.466.6.1.13.1.3 | INTEGER | read-write | The Board Level Timing for a 3000N. |
| dsucsuCfgDacsTable | 1.3.6.1.4.1.466.6.1.14 | |||
| dsucsuCfgAutoAssignTable | 1.3.6.1.4.1.466.6.1.14.1 | not-accessible | Automatically assign the proper amount of bandwidth. | |
| dsucsuCfgAutoAssignEntry | 1.3.6.1.4.1.466.6.1.14.1.1 | not-accessible | DACS auto assign Configuration Object. | |
| INT dsucsuConnAutoSlot | 1.3.6.1.4.1.466.6.1.14.1.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuConnAutoNode | 1.3.6.1.4.1.466.6.1.14.1.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuConnAutoSrcPort | 1.3.6.1.4.1.466.6.1.14.1.1.3 | INTEGER | read-only | Index to the 3000N source port of interest. 3000N supports two DTE-V35/RS-499 DATA ports (P3-P4). |
| INT dsucsuConnAutoStartDS0 | 1.3.6.1.4.1.466.6.1.14.1.1.4 | INTEGER | read-write | Port1/2 includes 24 DS0's. This value is the starting DS0 used by the node to allocate DS0s to meet port(3-4)-dte requirements. Sequential, contiguous DS0s are assigned. The number of DS0s required is based upon the DTE Data Rate and DTE Channel Mapping. The node's response to an entry may be gathered by querying dsucsuConnAutoStatus. To assign DS0s in a non-contiguous format, use the CfgEditConnTable. |
| INT dsucsuConnAutoDestPort | 1.3.6.1.4.1.466.6.1.14.1.1.5 | INTEGER | read-write | Selects the port for which DS0s are automatically allocated to one of the T1 network ports. Node software may not allow connection of port1 to port1. |
| INT dsucsuConnAutoType | 1.3.6.1.4.1.466.6.1.14.1.1.6 | INTEGER | read-write | Defines the type of traffic being transported. The 3000N supports data (1) or voice (2). The selected type will be assigned to all DS0s. |
| INT dsucsuConnDteRate | 1.3.6.1.4.1.466.6.1.14.1.1.7 | INTEGER | read-only | Data rate of the DTE port. Can be chaged from the CfgDteTable. |
| INT dsucsuConnDteDensity | 1.3.6.1.4.1.466.6.1.14.1.1.8 | INTEGER | read-only | Channel/DS0 format for the DTE port. Can be changed from the CfgDteTable. |
| INT dsucsuConnDs0Required | 1.3.6.1.4.1.466.6.1.14.1.1.9 | INTEGER | read-only | The number of DS0s required by the node's DTE port. This is based upon the DTE data rate and channel density selections. |
| INT dsucsuConnAutoStatus | 1.3.6.1.4.1.466.6.1.14.1.1.10 | INTEGER | read-only | Queries the node's connection status. Code will be returned when a connection set or update is rejected or accepted. |
| INT dsucsuConnAutoUpdateCmd | 1.3.6.1.4.1.466.6.1.14.1.1.11 | INTEGER | write-only | Updates the connections with the edit buffer. The edit buffer is comprised of any changes sent (set) from the dsucsuCfgAutoAssignEntry. |
| dsucsuCfgCurrentConnTable | 1.3.6.1.4.1.466.6.1.14.2 | not-accessible | Retrieves node's active connections assignments for display only. To edit connections, use CfgConnAutoAssign or CfgEditConnTable. | |
| dsucsuCfgCurrentConnections | 1.3.6.1.4.1.466.6.1.14.2.1 | not-accessible | An entry in the Current Connections Table. | |
| INT dsucsuSlot | 1.3.6.1.4.1.466.6.1.14.2.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuNode | 1.3.6.1.4.1.466.6.1.14.2.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuT1Index | 1.3.6.1.4.1.466.6.1.14.2.1.3 | INTEGER | read-only | Index to T1 network port of interest. The 3000N supports two NETWORK/DSX-1 ports. |
| INT dsucsuDs0 | 1.3.6.1.4.1.466.6.1.14.2.1.4 | INTEGER | read-only | DS0 number 1 through 24 corresponding to the T1 network port index. |
| INT dsucsuDtePort | 1.3.6.1.4.1.466.6.1.14.2.1.5 | INTEGER | read-only | DS0 assignment for indexed T1 network port. After making any adjustments to the connections, the dsucsuCfgConnUpdateCmd must be sent. Node software may not permit port 1 connections to itself. |
| INT dsucsuType | 1.3.6.1.4.1.466.6.1.14.2.1.6 | INTEGER | read-only | Defines the type of traffic being transported. The 3000N supports data (1) or voice (2). |
| dsucsuCfgEditConnTable | 1.3.6.1.4.1.466.6.1.14.3 | not-accessible | Manually assign the proper amount of bandwidth. | |
| dsucsuCfgEditConnEntry | 1.3.6.1.4.1.466.6.1.14.3.1 | not-accessible | Edits current DS0 assignment. After making any adjustments to the connections, the dsucsuCfgConnUpdateCmd must be sent. | |
| INT dsucsuConnSlot | 1.3.6.1.4.1.466.6.1.14.3.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuConnNode | 1.3.6.1.4.1.466.6.1.14.3.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuConnSrcPort | 1.3.6.1.4.1.466.6.1.14.3.1.3 | INTEGER | read-only | Index to the source port of interest. The 3000N supports two NETWORK/DSX-1 and two DTE ports. |
| INT dsucsuConnSrcDs0 | 1.3.6.1.4.1.466.6.1.14.3.1.4 | INTEGER | read-only | The source DS0 number 1 through 24 corresponding to the T1 network port index |
| INT dsucsuConnDestPort | 1.3.6.1.4.1.466.6.1.14.3.1.5 | INTEGER | read-write | Index to the destination port of interest. The 3000N supports two NETWORK/DSX-1 and two DTE ports. |
| INT dsucsuConnDestDs0 | 1.3.6.1.4.1.466.6.1.14.3.1.6 | INTEGER | read-write | DS0 assignment for indexed T1 network port. After making any adjustments to the connections, the dsucsuConnUpdateCmd must be sent. Node software may not permit connections between the same port and itself. |
| INT dsucsuConnType | 1.3.6.1.4.1.466.6.1.14.3.1.7 | INTEGER | read-write | Defines the type of traffic being transported. The 3000N supports data (1) or voice (2). |
| INT dsucsuConnNumDs0s | 1.3.6.1.4.1.466.6.1.14.3.1.8 | INTEGER | read-write | The total number of Ds0s to be connected. The number of Ds0s must be between 1 and 24. |
| INT dsucsuConnSetStatus | 1.3.6.1.4.1.466.6.1.14.3.1.9 | INTEGER | read-only | Displays node status from the last SNMP issed set command. |
| INT dsucsuConnConnect | 1.3.6.1.4.1.466.6.1.14.3.1.10 | INTEGER | write-only | Updates the connections with the edit buffer. The edit buffer is comprised of any changes sent (set) from the CfgEditConnTable. |
| INT dsucsuConnUpdateRequired | 1.3.6.1.4.1.466.6.1.14.3.1.11 | INTEGER | read-only | Displays node status from the last connection update. |
| INT dsucsuConnUpdateCmd | 1.3.6.1.4.1.466.6.1.14.3.1.12 | INTEGER | write-only | Sends the updated connections from the edit buffer to the node. The edit buffer is comprised of any changes sent (set) from the CfgEditConnTable. |
| INT dsucsuConnClearEditBuff | 1.3.6.1.4.1.466.6.1.14.3.1.13 | INTEGER | write-only | Removes all changes from edit buffer. The edit buffer is comprised of any changes sent (set) from the CfgEditConnTable. |
| dsucsuDiagNetTable | 1.3.6.1.4.1.466.6.1.15 | not-accessible | A list of Network Diagnostic attributes. Loopbacks, tests and their respective results can be initiated, cancelled and examined. | |
| dsucsuDiagNetEntry | 1.3.6.1.4.1.466.6.1.15.1 | not-accessible | A Network Diagnostic entry | |
| INT dsucsuDiagNetSlot | 1.3.6.1.4.1.466.6.1.15.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuDiagNetNode | 1.3.6.1.4.1.466.6.1.15.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuDiagNetIndex | 1.3.6.1.4.1.466.6.1.15.1.3 | INTEGER | read-only | The network number to be examined for a particular node (3000N only). |
| INT dsucsuDiagNetLclNetAggLpbk | 1.3.6.1.4.1.466.6.1.15.1.4 | INTEGER | read-write | Enables the operator to control and examine the local aggregate loopback. This loopback occurs on the net side of the local transmit and receive logic. The unit continues to transmit data across the network and also loops the data back to its own receiver circuitry. |
| INT dsucsuDiagNetLclNetLpbk | 1.3.6.1.4.1.466.6.1.15.1.5 | INTEGER | read-write | Enables the operator to control and examine the local network loopback. This loopback allows the operator to disconnect the side of the network by transmitting the data recovered from the network. |
| INT dsucsuDiagNetLclNetPayload | 1.3.6.1.4.1.466.6.1.15.1.6 | INTEGER | read-write | Enables the operator to control and examine the network payload loopback. This loopback occurs on the net side of the local transmit and receive logic. The unit continues to transmit data across the network and also loops the data back to its own receiver circuitry. |
| INT dsucsuDiagNetLclNetBiDir | 1.3.6.1.4.1.466.6.1.15.1.7 | INTEGER | read-write | Enables the operator to control and examine the local network loopback. This loopback allows the operator to disconnect the side of the network by transmitting the data recovered from the network in both directions. |
| INT dsucsuDiagNetRemCsuLpbk | 1.3.6.1.4.1.466.6.1.15.1.8 | INTEGER | read-write | Enables the operator to control and examine the remote CSU loopback. This loopback allows the operator to test the operation of the local channel, the aggregate and the remote CSU. |
| INT dsucsuDiagNetRemDsuLpbk | 1.3.6.1.4.1.466.6.1.15.1.9 | INTEGER | read-write | Enables the operator to control and examine the remote aggregate loopback. This loopback allows the operator to test the entire system from the local unit through the network to the remote node's transmit and receive front end. |
| TIK dsucsuDiagNetEvElapTime | 1.3.6.1.4.1.466.6.1.15.1.10 | TimeTicks | read-only | The time elapsed since the Event Test started. The new Event Test commences as soon as the previous Event Test registers are cleared. |
| CTR dsucsuDiagNetEvCRC6Err | 1.3.6.1.4.1.466.6.1.15.1.11 | Counter | read-only | The number of CRC6 errors encountered during the Event Test period. |
| CTR dsucsuDiagNetEvOofErr | 1.3.6.1.4.1.466.6.1.15.1.12 | Counter | read-only | The number of Out-Of-Frame errors encountered during the Event Test period. |
| CTR dsucsuDiagNetErrEvents | 1.3.6.1.4.1.466.6.1.15.1.13 | Counter | read-only | The number of Errored Events encountered during the Event Test period. |
| INT dsucsuDiagNetClearEvReg | 1.3.6.1.4.1.466.6.1.15.1.14 | INTEGER | write-only | Clear all the Event Test registers. Automatically initiates a new Event Test. |
| dsucsuDiagDteTable | 1.3.6.1.4.1.466.6.1.16 | not-accessible | A list of DTE channel diagnostics. | |
| dsucsuDiagDteEntry | 1.3.6.1.4.1.466.6.1.16.1 | not-accessible | A DTE channel diagnostic entry | |
| INT dsucsuDiagDteSlot | 1.3.6.1.4.1.466.6.1.16.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuDiagDteNode | 1.3.6.1.4.1.466.6.1.16.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuDiagDteIndex | 1.3.6.1.4.1.466.6.1.16.1.3 | INTEGER | read-only | The channel number to be examined for a particular node. |
| INT dsucsuDiagDteLocalBiDir | 1.3.6.1.4.1.466.6.1.16.1.4 | INTEGER | read-write | This selection displays the status or controls the Local Channel Loopback for the selected channel. This is a local turnaround and is bi-directional. |
| INT dsucsuDiagDteLocalPayload | 1.3.6.1.4.1.466.6.1.16.1.5 | INTEGER | read-write | This selection displays the status or controls the Local Payload Channel Loopback for the selected channel. |
| INT dsucsuDiagDteRemLpbk | 1.3.6.1.4.1.466.6.1.16.1.6 | INTEGER | read-write | This selection displays the status or controls the Channel Remote Loopback for the selected channel. This loopback transmits a code to the remote node which will enable or disable a diagnostic loopback at the addressed channel. |
| INT dsucsuDiagDteBertTestAct | 1.3.6.1.4.1.466.6.1.16.1.7 | INTEGER | read-write | BERT test related actions: a: Starts a BERT test on a channel, b: Stops a BERT test on a channel, c: Inject Errors while the BERT test is running, d: Clears BERT test errors. |
| INT dsucsuDiagDteBertHourStrt | 1.3.6.1.4.1.466.6.1.16.1.8 | INTEGER | read-only | Displays the hour that the BERT test started. |
| INT dsucsuDiagDteBertMinStrt | 1.3.6.1.4.1.466.6.1.16.1.9 | INTEGER | read-only | Displays th minute that BERT test started. |
| TIK dsucsuDiagDteBertTimeElaps | 1.3.6.1.4.1.466.6.1.16.1.10 | TimeTicks | read-only | Elapsed time since the BERT Test started |
| CTR dsucsuDiagDteBertErrors | 1.3.6.1.4.1.466.6.1.16.1.11 | Counter | read-only | Number of BERT test errors encountered during the BERT Test. |
| dsucsuDiagFrmTable | 1.3.6.1.4.1.466.6.1.17 | not-accessible | A list of framed channel diagnostics. | |
| dsucsuDiagFrmEntry | 1.3.6.1.4.1.466.6.1.17.1 | not-accessible | A framed channel diagnostic entry | |
| INT dsucsuDiagFrmSlot | 1.3.6.1.4.1.466.6.1.17.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuDiagFrmNode | 1.3.6.1.4.1.466.6.1.17.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuDiagFrmIndex | 1.3.6.1.4.1.466.6.1.17.1.3 | INTEGER | read-only | The channel number to be examined for a particular node. |
| INT dsucsuDiagFrmLclLpbk | 1.3.6.1.4.1.466.6.1.17.1.4 | INTEGER | read-write | This selection displays the status or controls the Local Channel Loopback for the selected channel. This is a local turnaround and is bi-directional. |
| INT dsucsuDiagFrmLclPayload | 1.3.6.1.4.1.466.6.1.17.1.5 | INTEGER | read-write | This selection displays the status or controls the Channel Remote Loopback for the selected channel. This loopback transmits a code to the remote node which will enable or disable a diagnostic loopback at the addressed channel. This selection is applicable only for DSX type channels. |
| INT dsucsuDiagFrmLclBiDir | 1.3.6.1.4.1.466.6.1.17.1.6 | INTEGER | read-write | This selection displays the status or controls the DSX Loopback for the selected channel. This selection is applicable only for DSX channels. |
| INT dsucsuDiagFrmRemLpbk | 1.3.6.1.4.1.466.6.1.17.1.7 | INTEGER | read-write | This selection displays the status or controls the Local Channel Loopback for the selected channel. This loopback transmits a code to the remote node which will enable or disable a diagnostic loopback at the addressed channel. This selection is applicable only for DSX channels. |
| INT dsucsuDiagFrmLclDte | 1.3.6.1.4.1.466.6.1.17.1.8 | INTEGER | read-write | This selection displays the status or controls the Local Channel Loopback for the selected channel. This is a local turnaround and is bi-directional. This selection is applicable only for CSU type channels. |
| INT dsucsuDiagFrmLclDte2 | 1.3.6.1.4.1.466.6.1.17.1.9 | INTEGER | read-write | This selection displays the status or controls the Channel Remote Loopback for the selected channel. This loopback transmits a code to the remote node which will enable or disable a diagnostic loopback at the addressed channel. This selection is applicable only for CSU type channels. |
| INT dsucsuDiagFrmBertTestAct | 1.3.6.1.4.1.466.6.1.17.1.10 | INTEGER | read-write | BERT test related actions: a: Starts a BERT test on a channel, b: Stops a BERT test on a channel, c: Inject Errors while the BERT test is running, d: Clears BERT test errors. |
| TIK dsucsuDiagFrmEvElapTime | 1.3.6.1.4.1.466.6.1.17.1.11 | TimeTicks | read-only | The time elapsed since the PBX Event Test started. This selection is applicable only for PBX channels. |
| CTR dsucsuDiagFrmEvBpvErr | 1.3.6.1.4.1.466.6.1.17.1.12 | Counter | read-only | The number of Bipolar Violations encountered during the Event Test. This selection is applicable only for PBX channels. |
| CTR dsucsuDiagFrmEvOofErr | 1.3.6.1.4.1.466.6.1.17.1.13 | Counter | read-only | The number of Out-Of-Frame Errors encountered during the Event Test. This selection is applicable only for PBX channels. |
| CTR dsucsuDiagFrmFrameErr | 1.3.6.1.4.1.466.6.1.17.1.14 | Counter | read-only | The number of Frame Errors encountered during the Event Test. This selection is applicable only for PBX channels. |
| INT dsucsuDiagFrmClearEvReg | 1.3.6.1.4.1.466.6.1.17.1.15 | INTEGER | write-only | Clears all the PBX Event Test registers. This selection is applicable only for PBX channels. |
| dsucsuDiagAuxTable | 1.3.6.1.4.1.466.6.1.18 | not-accessible | Auxillary Channel Diagnostics | |
| dsucsuDiagAuxEntry | 1.3.6.1.4.1.466.6.1.18.1 | not-accessible | Auxilary diagnostic entry | |
| INT dsucsuDiagAuxSlot | 1.3.6.1.4.1.466.6.1.18.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuDiagAuxNode | 1.3.6.1.4.1.466.6.1.18.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuDiagAuxChAStatus | 1.3.6.1.4.1.466.6.1.18.1.3 | INTEGER | read-only | Status of Supervisory link channel A. |
| INT dsucsuDiagAuxChBStatus | 1.3.6.1.4.1.466.6.1.18.1.4 | INTEGER | read-only | Status of Supervisory Link Channel B. |
| INT dsucsuDiagAuxFdlStatus | 1.3.6.1.4.1.466.6.1.18.1.5 | INTEGER | read-only | Status of Facility Data Link (PORT1). |
| INT dsucsuDiagAuxFdl2Status | 1.3.6.1.4.1.466.6.1.18.1.6 | INTEGER | read-only | Status of Facility Data Link (PORT2). |
| INT dsucsuDiagAuxMaintStatus | 1.3.6.1.4.1.466.6.1.18.1.7 | INTEGER | read-only | The Maint. Port Supervisory link status. |
| INT dsucsuDiagAuxCommStatus | 1.3.6.1.4.1.466.6.1.18.1.8 | INTEGER | read-only | The Communications port Supervisory link status. |
| dsucsuDiagPortTable | 1.3.6.1.4.1.466.6.1.19 | not-accessible | Port Specific Display only Diagnostics | |
| dsucsuDiagPortEntry | 1.3.6.1.4.1.466.6.1.19.1 | not-accessible | Port Specific Display only entry | |
| INT dsucsuDiagPortSlot | 1.3.6.1.4.1.466.6.1.19.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuDiagPortNode | 1.3.6.1.4.1.466.6.1.19.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuDiagPortIndex | 1.3.6.1.4.1.466.6.1.19.1.3 | INTEGER | read-only | The port index: unique per port. |
| INT dsucsuDiagPortType | 1.3.6.1.4.1.466.6.1.19.1.4 | INTEGER | read-only | The port type (NET/DSX/PBX/V.35/RS-449). |
| INT dsucsuDiagPortStatus | 1.3.6.1.4.1.466.6.1.19.1.5 | INTEGER | read-only | Current status condition of a particular port. |
| dsucsuIntervalTable | 1.3.6.1.4.1.466.6.1.20 | not-accessible | The table contains various ESF stats collected over the last 96 15-minute intervals (24 hours total time). | |
| dsucsuIntervalEntry | 1.3.6.1.4.1.466.6.1.20.1 | not-accessible | Entry in the table of ESF interval stats. | |
| INT dsucsuIntervalSlot | 1.3.6.1.4.1.466.6.1.20.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuIntervalNode | 1.3.6.1.4.1.466.6.1.20.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuIntervalPort | 1.3.6.1.4.1.466.6.1.20.1.3 | INTEGER | read-only | The port index: unique per port. |
| INT dsucsuIntervalNum | 1.3.6.1.4.1.466.6.1.20.1.4 | INTEGER | read-only | The sequence number for the selected interval. |
| CTR dsucsuIntervalESs | 1.3.6.1.4.1.466.6.1.20.1.5 | Counter | read-only | The number of Errored Seconds (as defined in Bell Publication 62411) encountered in the user registers during the selected interval. |
| CTR dsucsuIntervalSESs | 1.3.6.1.4.1.466.6.1.20.1.6 | Counter | read-only | The number of Severely Errored Seconds (as defined in Bell Publication 62411) encountered in the user registers during the selected interval. |
| CTR dsucsuIntervalBPVs | 1.3.6.1.4.1.466.6.1.20.1.7 | Counter | read-only | The number of Bipolar Violations (as defined in Bell Publication 62411) encountered in the user registers during the selected interval. |
| CTR dsucsuIntervalFSs | 1.3.6.1.4.1.466.6.1.20.1.8 | Counter | read-write | The number of Failed Seconds (as defined in Bell Publication 62411) encountered in the user registers during the selected interval. |
| dsucsuCurrentTable | 1.3.6.1.4.1.466.6.1.22 | not-accessible | The table contains various ESF stats collected over the current 15-minute interval. | |
| dsucsuCurrentEntry | 1.3.6.1.4.1.466.6.1.22.1 | not-accessible | Entry in the table of the current ESF stats. | |
| INT dsucsuCurrentSlot | 1.3.6.1.4.1.466.6.1.22.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuCurrentNode | 1.3.6.1.4.1.466.6.1.22.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuCurrentPort | 1.3.6.1.4.1.466.6.1.22.1.3 | INTEGER | read-only | The port index: unique per port. |
| CTR dsucsuCurrentESs | 1.3.6.1.4.1.466.6.1.22.1.4 | Counter | read-only | The number of Errored Seconds (as defined in Bell Publication 62411) encountered in the user registers during the current 15 minute interval. |
| CTR dsucsuCurrentSESs | 1.3.6.1.4.1.466.6.1.22.1.5 | Counter | read-only | The number of Severely Errored Seconds (as defined in Bell Publication 62411) encountered in the user registers during the current 15 minute interval. |
| CTR dsucsuCurrentBPVs | 1.3.6.1.4.1.466.6.1.22.1.6 | Counter | read-only | The number of Bipolar Violations (as defined in Bell Publication 62411) encountered in the user registers during the current 15 minute interval. |
| CTR dsucsuCurrentSECs | 1.3.6.1.4.1.466.6.1.22.1.7 | Counter | read-only | Number of seconds elapsed in the current 15 minute interval. |
| INT dsucsuCurrentStatus | 1.3.6.1.4.1.466.6.1.22.1.8 | INTEGER | read-write | Indication of whether statistics have been halted during current 15 minute interval. |
| dsucsuTotalTable | 1.3.6.1.4.1.466.6.1.24 | not-accessible | The table contains the cummulative sum of various ESF stats collected over the last 24 hour period. | |
| dsucsuTotalEntry | 1.3.6.1.4.1.466.6.1.24.1 | not-accessible | Entry in the table of the total ESF stats. | |
| INT dsucsuTotalSlot | 1.3.6.1.4.1.466.6.1.24.1.1 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuTotalNode | 1.3.6.1.4.1.466.6.1.24.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| INT dsucsuTotalPort | 1.3.6.1.4.1.466.6.1.24.1.3 | INTEGER | read-only | The port index: unique per port. |
| CTR dsucsuTotalESs | 1.3.6.1.4.1.466.6.1.24.1.4 | Counter | read-only | The number of Errored Seconds (as defined in Bell Publication 62411) encountered in the user registers in the last 24 hour period (96 intervals). |
| CTR dsucsuTotalSESs | 1.3.6.1.4.1.466.6.1.24.1.5 | Counter | read-only | The number of Severely Errored Seconds (as defined in Bell Publication 62411) encountered in the user registers in the last 24 hour period (96 intervals). |
| CTR dsucsuTotalBPVs | 1.3.6.1.4.1.466.6.1.24.1.6 | Counter | read-only | The number of Bipolar Violations (as defined in Bell Publication 62411) encountered in the user registers in the last 24 hour period (96 intervals). |
| CTR dsucsuTotalSECs | 1.3.6.1.4.1.466.6.1.24.1.7 | Counter | read-only | Number of seconds elapsed in the last 24 hours. This will be the maximum value of 86400 unless the addressed node was brought on-line with the this period. |
| INT dsucsuTotalStatus | 1.3.6.1.4.1.466.6.1.24.1.8 | INTEGER | read-write | Indication of whether statistics have been halted in the last 24 hours. |
| INT dsucsuAlarmType | 1.3.6.1.4.1.466.6.1.25 | INTEGER | read-only | The type of alarms that are generated on the node |
| INT dsucsuAlarmSlot | 1.3.6.1.4.1.466.6.1.26 | INTEGER | read-only | The PC port to which the TyView node is attached. |
| INT dsucsuAlarmNode | 1.3.6.1.4.1.466.6.1.27 | INTEGER | read-only | The node ID: unique per port ID. |
| STR dsucsuAlarmName | 1.3.6.1.4.1.466.6.1.28 | DisplayString | read-only | The name of the node which triggered the alarm. |
| tyview | 1.3.6.1.4.1.466.6.2 | |||
| tyviewSysTable | 1.3.6.1.4.1.466.6.2.1 | |||
| STR tyviewSysRevSw | 1.3.6.1.4.1.466.6.2.1.1 | DisplayString | read-only | The TyView software revision. |
| STR tyviewSysName | 1.3.6.1.4.1.466.6.2.1.2 | DisplayString | read-write | The name given to TyView system. |
| INT tyviewSysId | 1.3.6.1.4.1.466.6.2.1.3 | INTEGER | read-only | The TyView system ID. |
| INT tyviewSysTimeOutFactor | 1.3.6.1.4.1.466.6.2.1.4 | INTEGER | read-write | The TyView timeout factor. |
| STR tyviewSysObjectId | 1.3.6.1.4.1.466.6.2.1.5 | DisplayString | read-write | The Tyview Domain Object Identifier. |
| INT tyviewSysSlotNumber | 1.3.6.1.4.1.466.6.2.1.6 | INTEGER | read-only | The Physical Slot Number the NETEXEC is installed in. |
| INT tyviewSysClearDatabase | 1.3.6.1.4.1.466.6.2.1.7 | INTEGER | write-only | Clear the node database. |
| STR tyviewSysGetCommName | 1.3.6.1.4.1.466.6.2.1.8 | DisplayString | read-write | The GET community name. |
| STR tyviewSysSetCommName | 1.3.6.1.4.1.466.6.2.1.9 | DisplayString | read-write | The SET community name. |
| STR tyviewSysTrapCommName | 1.3.6.1.4.1.466.6.2.1.10 | DisplayString | read-write | The TRAP community name. |
| STR tyviewSysN1TrapDest | 1.3.6.1.4.1.466.6.2.1.11 | DisplayString | read-write | The first Trap IP Destination. |
| STR tyviewSysN2TrapDest | 1.3.6.1.4.1.466.6.2.1.12 | DisplayString | read-write | The second Trap IP Destination. |
| STR tyviewSysDate | 1.3.6.1.4.1.466.6.2.1.13 | DisplayString | read-write | The NETEXEC date (mm/dd/yy). |
| STR tyviewSysTime | 1.3.6.1.4.1.466.6.2.1.14 | DisplayString | read-write | The NETEXEC time (hh:mm). |
| INT tyviewSysMjrMnrLED | 1.3.6.1.4.1.466.6.2.1.15 | INTEGER | read-only | The Major/Minor LED status. |
| INT tyviewSysFanPSLED | 1.3.6.1.4.1.466.6.2.1.16 | INTEGER | read-only | The Fan / Power Supply LED status. |
| INT tyviewSysCtlrLED | 1.3.6.1.4.1.466.6.2.1.17 | INTEGER | read-only | The Controller LED status. |
| INT tyviewSysSlipLED | 1.3.6.1.4.1.466.6.2.1.18 | INTEGER | read-only | The SLIP LED status. |
| INT tyviewSysCtlChLED | 1.3.6.1.4.1.466.6.2.1.19 | INTEGER | read-only | The Control Channel LED status. |
| INT tyviewSysTDMLED | 1.3.6.1.4.1.466.6.2.1.20 | INTEGER | read-only | The TDM LED status. |
| INT tyviewSysMaintUseage | 1.3.6.1.4.1.466.6.2.1.21 | INTEGER | read-write | The Maintenance Port useage specification. |
| INT tyviewSysMaintDataBits | 1.3.6.1.4.1.466.6.2.1.22 | INTEGER | read-write | The Maintenance Port databits specification. |
| INT tyviewSysMaintRate | 1.3.6.1.4.1.466.6.2.1.23 | INTEGER | read-write | The Maintenance Port rate specification. |
| INT tyviewSysMaintStopBits | 1.3.6.1.4.1.466.6.2.1.24 | INTEGER | read-write | The Maintenance Port stopbits specification. |
| INT tyviewSysMaintParity | 1.3.6.1.4.1.466.6.2.1.25 | INTEGER | read-write | The Maintenance Port parity specification. |
| INT tyviewSysMaintMtu | 1.3.6.1.4.1.466.6.2.1.26 | INTEGER | read-write | The Maintenance Port maximum trans unit size. |
| INT tyviewSysMaintCompression | 1.3.6.1.4.1.466.6.2.1.27 | INTEGER | read-write | The Maintenance Port compression specification. |
| STR tyviewSysMaintSubnetMask | 1.3.6.1.4.1.466.6.2.1.28 | DisplayString | read-write | The Maintenance Port subnet mask. |
| STR tyviewSysMaintLocalIP | 1.3.6.1.4.1.466.6.2.1.29 | DisplayString | read-write | The Maintenance Port local IP address. |
| STR tyviewSysMaintPeerIP | 1.3.6.1.4.1.466.6.2.1.30 | DisplayString | read-write | The Maintenance Port peer IP address. |
| INT tyviewSysComUseage | 1.3.6.1.4.1.466.6.2.1.31 | INTEGER | read-write | The Com Port useage specification. |
| INT tyviewSysComDataBits | 1.3.6.1.4.1.466.6.2.1.32 | INTEGER | read-write | The Com Port databits specification. |
| INT tyviewSysComRate | 1.3.6.1.4.1.466.6.2.1.33 | INTEGER | read-write | The Com Port rate specification. |
| INT tyviewSysComStopBits | 1.3.6.1.4.1.466.6.2.1.34 | INTEGER | read-write | The Com Port stopbits specification. |
| INT tyviewSysComParity | 1.3.6.1.4.1.466.6.2.1.35 | INTEGER | read-write | The Com Port parity specification. |
| INT tyviewSysComMtu | 1.3.6.1.4.1.466.6.2.1.36 | INTEGER | read-write | The Com Port maximum trans unit size. |
| INT tyviewSysComCompression | 1.3.6.1.4.1.466.6.2.1.37 | INTEGER | read-write | The Com Port compression specification. |
| STR tyviewSysComSubnetMask | 1.3.6.1.4.1.466.6.2.1.38 | DisplayString | read-write | The Com Port subnet mask. |
| STR tyviewSysComLocalIP | 1.3.6.1.4.1.466.6.2.1.39 | DisplayString | read-write | The Com Port local IP address. |
| STR tyviewSysComPeerIP | 1.3.6.1.4.1.466.6.2.1.40 | DisplayString | read-write | The Com Port peer IP address. |
| INT tyviewSysTelnetEna | 1.3.6.1.4.1.466.6.2.1.41 | INTEGER | read-write | The Telnet log-in enable. |
| INT tyviewSysTelnetTO | 1.3.6.1.4.1.466.6.2.1.42 | INTEGER | read-write | The Telnet auto-logout timeout (minutes). |
| INT tyviewSysClrMjrMin | 1.3.6.1.4.1.466.6.2.1.43 | INTEGER | write-only | Clear major/minor alarm window / LED. |
| tyviewDatabaseTable | 1.3.6.1.4.1.466.6.2.2 | not-accessible | A list of tyview database entries. | |
| tyviewDatabaseEntry | 1.3.6.1.4.1.466.6.2.2.1 | not-accessible | System Object for TyView Database | |
| INT tyviewDatabaseSlot | 1.3.6.1.4.1.466.6.2.2.1.1 | INTEGER | read-only | The PC port to which the node is attached. |
| INT tyviewDatabaseNode | 1.3.6.1.4.1.466.6.2.2.1.2 | INTEGER | read-only | The node ID: unique per port ID. |
| STR tyviewDatabaseName | 1.3.6.1.4.1.466.6.2.2.1.3 | DisplayString | read-write | The unique name of the node. |
| INT tyviewDatabaseStatus | 1.3.6.1.4.1.466.6.2.2.1.4 | INTEGER | read-only | The last comm status. |
| tyviewBroadcastTable | 1.3.6.1.4.1.466.6.2.3 | |||
| INT tyviewBroadcastSetTime | 1.3.6.1.4.1.466.6.2.3.1 | INTEGER | write-only | Broadcast the time to all nodes. |
| INT tyviewBroadcastForwardAlarms | 1.3.6.1.4.1.466.6.2.3.2 | INTEGER | write-only | Broadcast alarm forwarding. |
| INT tyviewBroadcastClearLoopbacks | 1.3.6.1.4.1.466.6.2.3.3 | INTEGER | write-only | Broadcast Clearing of loopbacks. |
| tyviewTPTable | 1.3.6.1.4.1.466.6.2.4 | not-accessible | A list of Threshold Processing records. | |
| tyviewTPEntry | 1.3.6.1.4.1.466.6.2.4.1 | not-accessible | System Object for Threshold Processing | |
| INT tyviewTPRecord | 1.3.6.1.4.1.466.6.2.4.1.1 | INTEGER | read-only | The Threshold Processing record referenced. |
| INT tyviewTPMonNodeMode | 1.3.6.1.4.1.466.6.2.4.1.2 | INTEGER | read-write | The mode used for monitoring nodes. |
| STR tyviewTPNode | 1.3.6.1.4.1.466.6.2.4.1.3 | DisplayString | read-write | The node name for node-specific monitoring. |
| INT tyviewTPAlarmType | 1.3.6.1.4.1.466.6.2.4.1.4 | INTEGER | read-write | The alarm type used to trigger. |
| INT tyviewTPTriggerEvent | 1.3.6.1.4.1.466.6.2.4.1.5 | INTEGER | read-write | The event type used to trigger. |
| INT tyviewTPInstance | 1.3.6.1.4.1.466.6.2.4.1.6 | INTEGER | read-write | The alarm instance used to trigger. |
| INT tyviewTPInterval | 1.3.6.1.4.1.466.6.2.4.1.7 | INTEGER | read-write | The alarm interval used to trigger. |
| STR tyviewTPEventAction | 1.3.6.1.4.1.466.6.2.4.1.8 | DisplayString | read-write | The phone number dialed when triggered. |
| INT tyviewTPDryContact | 1.3.6.1.4.1.466.6.2.4.1.9 | INTEGER | read-write | The type of Dry Contact when triggered. |
| INT tyviewTPClearDryContact | 1.3.6.1.4.1.466.6.2.4.1.10 | INTEGER | write-only | Clear major/minor Dry Contact. |
RFC description
SNMP MIB module for managing network execution and multiprotocol network operations across distributed systems, providing monitoring and control of remote command execution capabilities.
Start monitoring DSU/CSU network element / digital access cross-connect system (DACS) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.