All MIBs › MG-SNMP-UPS-MIB
Category: Power Management, UPS
Description: Tracks battery status, load, and power events for Minuteman/Para Systems UPS units.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is MG-SNMP-UPS-MIB?
This is a private MIB (associated with Merlin Gerin/Minuteman/Para Systems UPS lineage) for monitoring uninterruptible power supply units, exposing manufacturer/model identity along with 'manager' (network management card) inventory objects. It covers device identification (family, model, revision, firmware version, serial number, installation date) and a table of management interface cards associated with the UPS. While the captured object list emphasizes identity data, MIBs in this family typically also expose battery status, load percentage, input/output voltage, and power event (on-battery, low-battery, overload) traps, making this squarely a power-hardware health MIB. It is a private vendor MIB, sometimes used alongside the standard UPS-MIB (RFC 1628) where both are supported for broader tool compatibility. It is deployed in data centers, server rooms, and network closets to protect against power loss, giving operators advance warning of battery depletion or utility power failure through MG-SNMP-UPS-MIB SNMP monitoring of the UPS and its management cards.
IPNetwork Monitor allows you to monitor SNMP objects defined in MG-SNMP-UPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Minuteman/Para Systems (Merlin Gerin lineage) UPS unit
Monitoring Examples
A facilities monitoring system would poll upsmgIdentFirmwareVersion and upsmgIdentSerialNumber to maintain an accurate hardware inventory of UPS units across sites, flagging any running outdated firmware. mgmanagerDeviceNumber and upsmgManagersTable would be walked to enumerate all network management cards reporting into a given UPS, useful in larger installations with multiple management interfaces. In combination with battery/load objects from this or a companion standard UPS-MIB, an operator would be alerted the moment a unit switches to battery power during a utility outage.
What Can Be Monitored
- UPS model/family and firmware version
- serial number and installation date
- management card inventory
- battery/power event status (via companion objects)
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| IpAddress | |
| TimeTicks | |
| enterprises |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| merlinGerin | 1.3.6.1.4.1.705 | |||
| upsmg | 1.3.6.1.4.1.705.1 | |||
| upsmgIdent | 1.3.6.1.4.1.705.1.1 | |||
| STR upsmgIdentFamilyName | 1.3.6.1.4.1.705.1.1.1 | DisplayString | read-write | The UPS family name (e.g. `PULSAR', `COMET', `GALAXY', ...). |
| STR upsmgIdentModelName | 1.3.6.1.4.1.705.1.1.2 | DisplayString | read-write | The UPS model name (e.g. `PSX20', `SV9', ... ). |
| STR upsmgIdentRevisionLevel | 1.3.6.1.4.1.705.1.1.3 | DisplayString | read-write | The UPS revision level. |
| STR upsmgIdentFirmwareVersion | 1.3.6.1.4.1.705.1.1.4 | DisplayString | read-write | The UPS microprocessor firmware version number. |
| STR upsmgIdentUserID | 1.3.6.1.4.1.705.1.1.5 | DisplayString | read-write | The UPS user identification (set by administrator). |
| STR upsmgIdentInstallationDate | 1.3.6.1.4.1.705.1.1.6 | DisplayString | read-write | The UPS installation date in dd/mm/yy format. |
| STR upsmgIdentSerialNumber | 1.3.6.1.4.1.705.1.1.7 | DisplayString | read-write | The UPS manufacturing serial number. |
| upsmgManagement | 1.3.6.1.4.1.705.1.2 | |||
| INT upsmgManagersNum | 1.3.6.1.4.1.705.1.2.1 | INTEGER | read-only | The number of managers that could manage the UPS. |
| upsmgManagersTable | 1.3.6.1.4.1.705.1.2.2 | not-accessible | The table of managers. | |
| upsmgManagersEntry | 1.3.6.1.4.1.705.1.2.2.1 | not-accessible | The description of a manager entry in the managers table. | |
| INT mgmanagerIndex | 1.3.6.1.4.1.705.1.2.2.1.1 | INTEGER | read-only | A unique value for each manager. Its value ranges between 1 and the value of upsmgManagersNum. |
| INT mgmanagerDeviceNumber | 1.3.6.1.4.1.705.1.2.2.1.2 | INTEGER | read-write | This object is the number of the manager device in the DevicesTable of the Config group. This means that the manager is powered by the UPS. If not the default value is 0. |
| INT mgmanagerNMSType | 1.3.6.1.4.1.705.1.2.2.1.3 | INTEGER | read-write | The type of manager according to the NMS platform. We include in the manager class all systems which will be notified by the agent via receiving traps (e.g. basic to complex NMS software). |
| INT mgmanagerCommType | 1.3.6.1.4.1.705.1.2.2.1.4 | INTEGER | read-write | The level of communication protocol for that manager. Setting this object to value invalid(2) has the effect of invalidating the corresponding entry in the upsmgManagersTable. It is an implementation-specific matter as to wether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entry not currently in use. Proper interpretation of such entries requires examination of the relevant mgmanagerCommType object. |
| STR mgmanagerDescr | 1.3.6.1.4.1.705.1.2.2.1.5 | DisplayString | read-write | A textual string containing information about the manager. (manufacturer and version description). |
| IP mgmanagerAddress | 1.3.6.1.4.1.705.1.2.2.1.6 | IpAddress | read-write | The IP address of the manager station receiving traps. The value of this object is meaningful if and only if the value of the relevant mgmanagerCommType object is snmp type. |
| STR mgmanagerCommunity | 1.3.6.1.4.1.705.1.2.2.1.7 | DisplayString | read-write | The manager community string. |
| INT mgmanagerSeverityLevel | 1.3.6.1.4.1.705.1.2.2.1.8 | INTEGER | read-write | The severity level of traps to be received by this manager. |
| INT mgmanagerTrapAck | 1.3.6.1.4.1.705.1.2.2.1.9 | INTEGER | read-write | The manager Trap Acknowledgement status. Setting this object to mgnoack(2) or stdnomg(3) or cpqnoack(5) disables the trap acknowledgement from the related manager. The MG enterprise specific trap should then be sent only once by the agent to this manager in case of mgnoack(2), and should not be sent by the agent to this manager in case of stdnomg(3) or cpqnoack(5). mgack(1) allows a basic mecanism for acknowledged traps using upsmgAgentTrapAck object set by the manager to the enterprise specific number of the trap. mgacks(5) allows the enhanced mecanism using the upsmgAgentTrapSignature object set by the manager to the signature received within the trap var binding. |
| upsmgReceptacle | 1.3.6.1.4.1.705.1.3 | |||
| INT upsmgReceptaclesNum | 1.3.6.1.4.1.705.1.3.1 | INTEGER | read-only | The total number of receptacles controlled by the UPS. |
| upsmgReceptaclesTable | 1.3.6.1.4.1.705.1.3.2 | not-accessible | The table of receptacles that are controlled by the UPS. | |
| upsmgReceptaclesEntry | 1.3.6.1.4.1.705.1.3.2.1 | not-accessible | The description of a receptacle in the table. | |
| INT mgreceptacleIndex | 1.3.6.1.4.1.705.1.3.2.1.1 | INTEGER | read-only | A unique value for each receptacle. Its value ranges between 1 and the value of upsmgReceptaclesNum. |
| INT mgreceptacleLevel | 1.3.6.1.4.1.705.1.3.2.1.2 | INTEGER | read-write | The level of receptacle. Setting this object to value invalid(2) has the effect of invalidating the corresponding entry in the upsmgReceptaclesTable. It is an implementation-specific matter as to wether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entry not currently in use. Proper interpretation of such entries requires examination of the relevant receptacleLevel object. Values 1 and 4 are reserved, value 3 is used to identify a simple one-level receptacle, and values greater than 4 represent a group of equivalent receptacles. |
| STR mgreceptacleType | 1.3.6.1.4.1.705.1.3.2.1.3 | DisplayString | read-write | A textual string for the receptacle type. |
| STR mgreceptacleIdent | 1.3.6.1.4.1.705.1.3.2.1.4 | DisplayString | read-write | A textual string identification for the user. |
| INT mgreceptacleState | 1.3.6.1.4.1.705.1.3.2.1.5 | INTEGER | read-only | The ON/OFF status of the receptacle. |
| INT mgreceptacleReceptacle | 1.3.6.1.4.1.705.1.3.2.1.6 | INTEGER | read-write | The receptacle number of the second level receptacle father. The value of this object is meaningful if and only if the value of the relevant mgreceptacleType object is related to a two-level receptacle class. Otherwise the default value is 0. |
| INT mgreceptaclePowerCons | 1.3.6.1.4.1.705.1.3.2.1.7 | INTEGER | read-write | The volt-ampere rating of the receptacle. The value of this object is meaningful if and only if the value of the relevant mgreceptacleType object is related to a two-level receptacle class. Otherwise the default value is 0. |
| INT mgreceptacleOverload | 1.3.6.1.4.1.705.1.3.2.1.8 | INTEGER | read-write | The overload status of the receptacle. The value of this object is meaningful if and only if the value of the relevant mgreceptacleType object is related to a two-level receptacle class. Otherwise the default value is 0. |
| INT mgreceptacleAutonomy | 1.3.6.1.4.1.705.1.3.2.1.9 | INTEGER | read-write | The receptacle autonomy. The value of this object is meaningful if and only if the value of the relevant mgreceptacleType object is related to a two-level receptacle class. Otherwise the default value is 0. |
| upsmgConfig | 1.3.6.1.4.1.705.1.4 | |||
| INT upsmgConfigBatteryInstalled | 1.3.6.1.4.1.705.1.4.1 | INTEGER | read-write | The battery installed status. |
| INT upsmgConfigNominalBatteryVoltage | 1.3.6.1.4.1.705.1.4.2 | INTEGER | read-write | The nominal battery voltage. |
| INT upsmgConfigNominalBatteryTime | 1.3.6.1.4.1.705.1.4.3 | INTEGER | read-write | The full load battery autonomy time. |
| INT upsmgConfigNominalRechargeTime | 1.3.6.1.4.1.705.1.4.4 | INTEGER | read-write | The recharge time to go from low battery cut off to full charge at full load. |
| INT upsmgConfigMinRechargeLevel | 1.3.6.1.4.1.705.1.4.5 | INTEGER | read-write | The minimum battery level required to supply power on the loads after low battery condition turn off and restart on main return. |
| INT upsmgConfigMaxRechargeTime | 1.3.6.1.4.1.705.1.4.6 | INTEGER | read-write | The maximum time delay of battery recharge before supply power to the loads. |
| INT upsmgConfigLowBatteryTime | 1.3.6.1.4.1.705.1.4.7 | INTEGER | read-write | To set remaining time value for low battery condition. |
| INT upsmgConfigLowBatteryLevel | 1.3.6.1.4.1.705.1.4.8 | INTEGER | read-write | To set battery level value for low battery condition. |
| INT upsmgConfigAutoRestart | 1.3.6.1.4.1.705.1.4.9 | INTEGER | read-write | The automatic restart enabling status. |
| INT upsmgConfigShutdownTimer | 1.3.6.1.4.1.705.1.4.10 | INTEGER | read-write | To set ups shutdown timer from on battery condition. |
| INT upsmgConfigSysShutDuration | 1.3.6.1.4.1.705.1.4.11 | INTEGER | read-write | To set ups shutdown delay (Sn delay). |
| INT upsmgConfigVARating | 1.3.6.1.4.1.705.1.4.12 | INTEGER | read-write | The UPS nominal VA rating. |
| INT upsmgConfigLowTransfer | 1.3.6.1.4.1.705.1.4.13 | INTEGER | read-write | The low voltage transfer point. |
| INT upsmgConfigHighTransfer | 1.3.6.1.4.1.705.1.4.14 | INTEGER | read-write | The high voltage transfer point. |
| INT upsmgConfigOutputNominalVoltage | 1.3.6.1.4.1.705.1.4.15 | INTEGER | read-write | The nominal output voltage. |
| INT upsmgConfigOutputNominalCurrent | 1.3.6.1.4.1.705.1.4.16 | INTEGER | read-write | The nominal output current. |
| INT upsmgConfigOutputNomFrequency | 1.3.6.1.4.1.705.1.4.17 | INTEGER | read-write | The nominal output frequency. |
| INT upsmgConfigByPassType | 1.3.6.1.4.1.705.1.4.18 | INTEGER | read-write | The UPS by pass switch type. |
| INT upsmgConfigAlarmAudible | 1.3.6.1.4.1.705.1.4.19 | INTEGER | read-write | To set audible alarm status. |
| INT upsmgConfigAlarmTimeDelay | 1.3.6.1.4.1.705.1.4.20 | INTEGER | read-write | To set audible alarm time delay. |
| INT upsmgConfigDevicesNum | 1.3.6.1.4.1.705.1.4.21 | INTEGER | read-write | The number of devices that are powered by the UPS. |
| upsmgConfigDevicesTable | 1.3.6.1.4.1.705.1.4.22 | not-accessible | The table of devices that are powered by the UPS. | |
| upsmgConfigDevicesEntry | 1.3.6.1.4.1.705.1.4.22.1 | not-accessible | The description of a device entry in the devices table. | |
| INT mgdeviceIndex | 1.3.6.1.4.1.705.1.4.22.1.1 | INTEGER | read-only | A unique value for each device. Its value ranges between 1 and the value of upsmgDevicesNum. |
| INT mgdeviceReceptacleNum | 1.3.6.1.4.1.705.1.4.22.1.2 | INTEGER | read-write | The receptacle number of the device plugged into the UPS. This value gives index entry in the ReceptaclesTable object of the Receptacle group. A value of 0 invalidates the entry in the DevicesTable. |
| STR mgdeviceIdent | 1.3.6.1.4.1.705.1.4.22.1.3 | DisplayString | read-write | A textual string for device user identification. |
| INT mgdeviceVaRating | 1.3.6.1.4.1.705.1.4.22.1.4 | INTEGER | read-write | The volt-ampere rating of the device plugged into the UPS. |
| INT mgdeviceSequenceOff | 1.3.6.1.4.1.705.1.4.22.1.5 | INTEGER | read-write | To set the device position in the remote shutdown sequence. |
| INT mgdeviceSequenceOn | 1.3.6.1.4.1.705.1.4.22.1.6 | INTEGER | read-write | To set the device position in the remote reboot sequence. |
| INT mgdeviceShutdownDuration | 1.3.6.1.4.1.705.1.4.22.1.7 | INTEGER | read-write | To set the duration from start of computer shut-down to complete. |
| INT mgdeviceBootUpDuration | 1.3.6.1.4.1.705.1.4.22.1.8 | INTEGER | read-write | To set the duration from start of computer boot-up to complete. |
| upsmgConfigReceptaclesTable | 1.3.6.1.4.1.705.1.4.23 | not-accessible | The table of receptacles. | |
| upsmgConfigReceptaclesEntry | 1.3.6.1.4.1.705.1.4.23.1 | not-accessible | The description of a receptacle entry in the table. | |
| INT mgreceptacleIndexb | 1.3.6.1.4.1.705.1.4.23.1.1 | INTEGER | read-only | A unique value for each receptacle. Its value ranges between 1 and the value of upsmgReceptaclesNum. |
| INT mgreceptacleStateTurnOn | 1.3.6.1.4.1.705.1.4.23.1.2 | INTEGER | read-write | Default return state at turn on. |
| INT mgreceptacleStateMainReturn | 1.3.6.1.4.1.705.1.4.23.1.3 | INTEGER | read-write | Default return state on main return. |
| INT mgreceptacleStateDischarge | 1.3.6.1.4.1.705.1.4.23.1.4 | INTEGER | read-write | Default return state on main return from battery discharge. |
| INT mgreceptacleShutoffLevel | 1.3.6.1.4.1.705.1.4.23.1.5 | INTEGER | read-write | Battery level for starting shutoff sequence. |
| INT mgreceptacleShutoffTimer | 1.3.6.1.4.1.705.1.4.23.1.6 | INTEGER | read-write | Time delay from on battery for starting shutoff sequence. |
| INT mgreceptacleRestartLevel | 1.3.6.1.4.1.705.1.4.23.1.7 | INTEGER | read-write | Battery level for starting restart sequence. |
| INT mgreceptacleRestartDelay | 1.3.6.1.4.1.705.1.4.23.1.8 | INTEGER | read-write | Time delay for starting restart sequence. |
| INT mgreceptacleShutdownDuration | 1.3.6.1.4.1.705.1.4.23.1.9 | INTEGER | read-only | Maximum Shutdown Duration for systems powered by this plug. |
| INT mgreceptacleBootUpDuration | 1.3.6.1.4.1.705.1.4.23.1.10 | INTEGER | read-only | Maximum Reboot Duration for systems powered by this plug. |
| INT upsmgConfigExtAlarmNum | 1.3.6.1.4.1.705.1.4.24 | INTEGER | read-only | The number of environ external alarm, value is between 8 and 32.. |
| upsmgConfigExtAlarmTable | 1.3.6.1.4.1.705.1.4.25 | not-accessible | The table of environmental external alarms. | |
| upsmgConfigExtAlarmEntry | 1.3.6.1.4.1.705.1.4.25.1 | not-accessible | The description of an external alarm in the table. | |
| INT mgextAlarmIndex | 1.3.6.1.4.1.705.1.4.25.1.1 | INTEGER | read-only | A unique value for each external alarm. Its value ranges between 1 and the value of upsmgConfigExtAlarmNum. |
| STR mgextAlarmUID | 1.3.6.1.4.1.705.1.4.25.1.2 | DisplayString | read-write | A textual string for alarm state user identification. |
| INT upsmgConfigEmergencyTestFail | 1.3.6.1.4.1.705.1.4.26 | INTEGER | read-write | The emergency condition status on Battery test fail. |
| INT upsmgConfigEmergencyOnByPass | 1.3.6.1.4.1.705.1.4.27 | INTEGER | read-write | The emergency condition status on By Pass. |
| INT upsmgConfigEmergencyOverload | 1.3.6.1.4.1.705.1.4.28 | INTEGER | read-write | The emergency condition status on overload. |
| upsmgConfigControlDayTable | 1.3.6.1.4.1.705.1.4.29 | not-accessible | The table of daily on/off time. | |
| upsmgConfigControlDayEntry | 1.3.6.1.4.1.705.1.4.29.1 | not-accessible | The description of a daily on/off time schedule in the table. | |
| INT mgcontrolDayIndex | 1.3.6.1.4.1.705.1.4.29.1.1 | INTEGER | read-only | The day index. It is a number between 1 and 7, 1 for Sunday, 2 for Monday, ... |
| INT mgcontrolDayOn | 1.3.6.1.4.1.705.1.4.29.1.2 | INTEGER | read-write | To set daily power on time. Any value greater than 86400 is to disable the Day On. |
| INT mgcontrolDayOff | 1.3.6.1.4.1.705.1.4.29.1.3 | INTEGER | read-write | To set daily power off time. Any value greater than 86400 is to disable the Day Off. |
| INT upsmgConfigLowBooster | 1.3.6.1.4.1.705.1.4.30 | INTEGER | read-write | To set UPS booster low threshold. |
| INT upsmgConfigHighBooster | 1.3.6.1.4.1.705.1.4.31 | INTEGER | read-write | To set UPS booster high threshold. |
| INT upsmgConfigLowFader | 1.3.6.1.4.1.705.1.4.32 | INTEGER | read-write | To set UPS fader low threshold. |
| INT upsmgConfigHighFader | 1.3.6.1.4.1.705.1.4.33 | INTEGER | read-write | To set UPS fader high threshold. |
| upsmgConfigEnvironmentTable | 1.3.6.1.4.1.705.1.4.34 | not-accessible | The table containing the configuration of the environment sensor. | |
| upsmgConfigEnvironmentEntry | 1.3.6.1.4.1.705.1.4.34.1 | not-accessible | The description of an entry in the table. | |
| INT upsmgConfigSensorIndex | 1.3.6.1.4.1.705.1.4.34.1.1 | INTEGER | read-only | The sensor index, ranging from 1 to upsmgEnvironmentNum. |
| STR upsmgConfigSensorName | 1.3.6.1.4.1.705.1.4.34.1.2 | DisplayString | read-write | The sensor user-friendly name. |
| INT upsmgConfigTemperatureLow | 1.3.6.1.4.1.705.1.4.34.1.3 | INTEGER | read-write | The low temperature threshold in unit 0.1 Cel. |
| INT upsmgConfigTemperatureHigh | 1.3.6.1.4.1.705.1.4.34.1.4 | INTEGER | read-write | The high temperature threshold in unit 0.1 Cel. |
| INT upsmgConfigTemperatureHysteresis | 1.3.6.1.4.1.705.1.4.34.1.5 | INTEGER | read-write | The temperature hysteresys used for threshold test in unit 0.1 Cel. |
| INT upsmgConfigHumidityLow | 1.3.6.1.4.1.705.1.4.34.1.6 | INTEGER | read-write | The low humidity threshold in unit 1 %. |
| INT upsmgConfigHumidityHigh | 1.3.6.1.4.1.705.1.4.34.1.7 | INTEGER | read-write | The high humidity threshold in unit 1 %. |
| INT upsmgConfigHumidityHysteresis | 1.3.6.1.4.1.705.1.4.34.1.8 | INTEGER | read-write | The humidity hysteresys used for threshold test in unit 1 %. |
| STR upsmgConfigInput1Name | 1.3.6.1.4.1.705.1.4.34.1.9 | DisplayString | read-write | The Input #1 user-friendly name. |
| STR upsmgConfigInput1ClosedLabel | 1.3.6.1.4.1.705.1.4.34.1.10 | DisplayString | read-write | The Input #1 label for closed position. |
| STR upsmgConfigInput1OpenLabel | 1.3.6.1.4.1.705.1.4.34.1.11 | DisplayString | read-write | The Input #1 label for open position. |
| STR upsmgConfigInput2Name | 1.3.6.1.4.1.705.1.4.34.1.12 | DisplayString | read-write | The Input #2 user-friendly name. |
| STR upsmgConfigInput2ClosedLabel | 1.3.6.1.4.1.705.1.4.34.1.13 | DisplayString | read-write | The Input #2 label for closed position. |
| STR upsmgConfigInput2OpenLabel | 1.3.6.1.4.1.705.1.4.34.1.14 | DisplayString | read-write | The Input #2 label for open position. |
| upsmgBattery | 1.3.6.1.4.1.705.1.5 | |||
| INT upsmgBatteryRemainingTime | 1.3.6.1.4.1.705.1.5.1 | INTEGER | read-only | The time remaining actual charge vs actual load (dynamic). |
| INT upsmgBatteryLevel | 1.3.6.1.4.1.705.1.5.2 | INTEGER | read-only | The battery level as a percentage of charge. |
| INT upsmgBatteryRechargeTime | 1.3.6.1.4.1.705.1.5.3 | INTEGER | read-only | The actual operational battery recharge time to set point equal to upsmgConfigRechargeLevel. This value is computed from upsmgConfigRechargeLevel (level to reach), upsmgBatteryLevel (the actual reached level) and the UPS charge rate. |
| INT upsmgBatteryRechargeLevel | 1.3.6.1.4.1.705.1.5.4 | INTEGER | read-only | The actual value of the battery recharge level that will be reached during the time delay necessary to restart after power returns. This value is computed from upsmgConfigRechargeTime (the delay), upsmgBatteryLevel (the actual level) and the UPS charge rate. |
| INT upsmgBatteryVoltage | 1.3.6.1.4.1.705.1.5.5 | INTEGER | read-only | The actual battery voltage. |
| INT upsmgBatteryCurrent | 1.3.6.1.4.1.705.1.5.6 | INTEGER | read-only | The actual battery current. |
| INT upsmgBatteryTemperature | 1.3.6.1.4.1.705.1.5.7 | INTEGER | read-only | The battery temperature. |
| INT upsmgBatteryFullRechargeTime | 1.3.6.1.4.1.705.1.5.8 | INTEGER | read-only | The battery full recharge time (from 0 to 100 percent) at current load. |
| INT upsmgBatteryFaultBattery | 1.3.6.1.4.1.705.1.5.9 | INTEGER | read-only | The battery fault status. |
| INT upsmgBatteryNoBattery | 1.3.6.1.4.1.705.1.5.10 | INTEGER | read-only | The UPS has no Battery status. |
| INT upsmgBatteryReplacement | 1.3.6.1.4.1.705.1.5.11 | INTEGER | read-only | The UPS Battery to be replaced status. |
| INT upsmgBatteryUnavailableBattery | 1.3.6.1.4.1.705.1.5.12 | INTEGER | read-only | The UPS Battery is unavailable status. |
| INT upsmgBatteryNotHighCharge | 1.3.6.1.4.1.705.1.5.13 | INTEGER | read-only | The UPS Battery quit high condition status. |
| INT upsmgBatteryLowBattery | 1.3.6.1.4.1.705.1.5.14 | INTEGER | read-only | The battery low status. |
| INT upsmgBatteryChargerFault | 1.3.6.1.4.1.705.1.5.15 | INTEGER | read-only | The UPS Battery is not charging status. |
| INT upsmgBatteryLowCondition | 1.3.6.1.4.1.705.1.5.16 | INTEGER | read-only | The UPS is at low condition status. |
| INT upsmgBatteryLowRecharge | 1.3.6.1.4.1.705.1.5.17 | INTEGER | read-only | The UPS Battery is not recharged status. |
| upsmgInput | 1.3.6.1.4.1.705.1.6 | |||
| INT upsmgInputPhaseNum | 1.3.6.1.4.1.705.1.6.1 | INTEGER | read-only | The number of input phases. |
| upsmgInputPhaseTable | 1.3.6.1.4.1.705.1.6.2 | not-accessible | The table of input phases. | |
| upsmgInputPhaseEntry | 1.3.6.1.4.1.705.1.6.2.1 | not-accessible | The description of an input phase. | |
| INT mginputIndex | 1.3.6.1.4.1.705.1.6.2.1.1 | INTEGER | read-only | The input phase voltage index. It is a number between 1 and upsmgInputPhaseNum. |
| INT mginputVoltage | 1.3.6.1.4.1.705.1.6.2.1.2 | INTEGER | read-only | The input phase voltage. |
| INT mginputFrequency | 1.3.6.1.4.1.705.1.6.2.1.3 | INTEGER | read-only | The input phase frequency. |
| INT mginputMinimumVoltage | 1.3.6.1.4.1.705.1.6.2.1.4 | INTEGER | read-only | The input phase minimum voltage over the last minute. |
| INT mginputMaximumVoltage | 1.3.6.1.4.1.705.1.6.2.1.5 | INTEGER | read-only | The input phase maximum voltage over the last minute. |
| INT mginputCurrent | 1.3.6.1.4.1.705.1.6.2.1.6 | INTEGER | read-only | The input phase current. |
| INT upsmgInputBadStatus | 1.3.6.1.4.1.705.1.6.3 | INTEGER | read-only | The utility power bad voltage or bad frequency status. |
| INT upsmgInputLineFailCause | 1.3.6.1.4.1.705.1.6.4 | INTEGER | read-only | The utility power failure cause: no(1) is for no utility failure, outoftolvolt(2) is for voltage out of tolerance, outoftolfreq(3) is for frequency out of tolerance, utilityoff(4) is for no voltage at all. |
| upsmgOutput | 1.3.6.1.4.1.705.1.7 | |||
| INT upsmgOutputPhaseNum | 1.3.6.1.4.1.705.1.7.1 | INTEGER | read-only | The number of output phases. |
| upsmgOutputPhaseTable | 1.3.6.1.4.1.705.1.7.2 | not-accessible | The table of output phases. | |
| upsmgOutputPhaseEntry | 1.3.6.1.4.1.705.1.7.2.1 | not-accessible | The description of an output phase. | |
| INT mgoutputPhaseIndex | 1.3.6.1.4.1.705.1.7.2.1.1 | INTEGER | read-only | The output phase voltage index. It is a number between 1 and upsmgOutputPhaseNum. |
| INT mgoutputVoltage | 1.3.6.1.4.1.705.1.7.2.1.2 | INTEGER | read-only | The output phase voltage. |
| INT mgoutputFrequency | 1.3.6.1.4.1.705.1.7.2.1.3 | INTEGER | read-only | The output phase frequency. |
| INT mgoutputLoadPerPhase | 1.3.6.1.4.1.705.1.7.2.1.4 | INTEGER | read-only | The output load per phase. |
| INT mgoutputCurrent | 1.3.6.1.4.1.705.1.7.2.1.5 | INTEGER | read-only | The output phase current. |
| INT upsmgOutputOnBattery | 1.3.6.1.4.1.705.1.7.3 | INTEGER | read-only | The UPS on battery / on main status. |
| INT upsmgOutputOnByPass | 1.3.6.1.4.1.705.1.7.4 | INTEGER | read-only | The UPS on bypass status. |
| INT upsmgOutputUnavailableByPass | 1.3.6.1.4.1.705.1.7.5 | INTEGER | read-only | The by pass unavailable status. |
| INT upsmgOutputNoByPass | 1.3.6.1.4.1.705.1.7.6 | INTEGER | read-only | The UPS bypass installed status. |
| INT upsmgOutputUtilityOff | 1.3.6.1.4.1.705.1.7.7 | INTEGER | read-only | The UPS utility off status. |
| INT upsmgOutputOnBoost | 1.3.6.1.4.1.705.1.7.8 | INTEGER | read-only | The UPS on booster status. |
| INT upsmgOutputInverterOff | 1.3.6.1.4.1.705.1.7.9 | INTEGER | read-only | The UPS Inverter on / off status. |
| INT upsmgOutputOverLoad | 1.3.6.1.4.1.705.1.7.10 | INTEGER | read-only | The output over load status. |
| INT upsmgOutputOverTemp | 1.3.6.1.4.1.705.1.7.11 | INTEGER | read-only | The ups over temperature status. |
| INT upsmgOutputOnBuck | 1.3.6.1.4.1.705.1.7.12 | INTEGER | read-only | The UPS on fader status. |
| upsmgEnviron | 1.3.6.1.4.1.705.1.8 | |||
| INT upsmgEnvironAmbientTemp | 1.3.6.1.4.1.705.1.8.1 | INTEGER | read-only | The ambient temperature. |
| INT upsmgEnvironAmbientHumidity | 1.3.6.1.4.1.705.1.8.2 | INTEGER | read-only | The ambient humidity. |
| upsmgEnvironExtAlarmTable | 1.3.6.1.4.1.705.1.8.3 | not-accessible | The table of external alarms. | |
| upsmgEnvironExtAlarmEntry | 1.3.6.1.4.1.705.1.8.3.1 | not-accessible | The description of an external alarm. | |
| INT mgalarmNum | 1.3.6.1.4.1.705.1.8.3.1.1 | INTEGER | read-only | The external alarm number. A number between 1 and upsmgConfigExtAlarmNum. |
| INT mgalarmState | 1.3.6.1.4.1.705.1.8.3.1.2 | INTEGER | read-only | The external alarm state (active or inactive). |
| INT upsmgEnvironSensorNum | 1.3.6.1.4.1.705.1.8.4 | INTEGER | read-only | The sensor unit number (0 to 4). |
| upsmgEnvironSensorTable | 1.3.6.1.4.1.705.1.8.5 | not-accessible | The table of sensor units. | |
| upsmgEnvironSensorEntry | 1.3.6.1.4.1.705.1.8.5.1 | not-accessible | The description of a sensor unit. | |
| INT mgsensorNum | 1.3.6.1.4.1.705.1.8.5.1.1 | INTEGER | read-only | The unit number. A number between 1 and 4. |
| INT mgsensorTemp | 1.3.6.1.4.1.705.1.8.5.1.2 | INTEGER | read-only | The measured temperature of the unit. |
| INT mgsensorHumidity | 1.3.6.1.4.1.705.1.8.5.1.3 | INTEGER | read-only | The measured humidity of the unit. |
| INT upsmgEnvironmentNum | 1.3.6.1.4.1.705.1.8.6 | INTEGER | read-only | Number of Environment sensor connected. |
| upsmgEnvironmentSensorTable | 1.3.6.1.4.1.705.1.8.7 | not-accessible | The table containing the measurements and alarms made by Environment sensor units. | |
| upsmgEnvironmentSensorEntry | 1.3.6.1.4.1.705.1.8.7.1 | not-accessible | The description of an entry in the measurement table. | |
| INT upsmgEnvironmentIndex | 1.3.6.1.4.1.705.1.8.7.1.1 | INTEGER | read-only | The sensor index, ranging from 1 to upsmgEnvironmentNum. |
| INT upsmgEnvironmentComFailure | 1.3.6.1.4.1.705.1.8.7.1.2 | INTEGER | read-only | The sensor communication failure : yes(1), no(2). |
| INT upsmgEnvironmentTemperature | 1.3.6.1.4.1.705.1.8.7.1.3 | INTEGER | read-only | The temperature measurement in unit 0.1 Cel. |
| INT upsmgEnvironmentTemperatureLow | 1.3.6.1.4.1.705.1.8.7.1.4 | INTEGER | read-only | Temperature is below low theshold : yes(1), no(2). |
| INT upsmgEnvironmentTemperatureHigh | 1.3.6.1.4.1.705.1.8.7.1.5 | INTEGER | read-only | Temperature is above high threshold : yes(1), no(2). |
| INT upsmgEnvironmentHumidity | 1.3.6.1.4.1.705.1.8.7.1.6 | INTEGER | read-only | The humidity measurement in unit 0.1 %. |
| INT upsmgEnvironmentHumidityLow | 1.3.6.1.4.1.705.1.8.7.1.7 | INTEGER | read-only | Humidity is below low threshold : yes(1), no(2). |
| INT upsmgEnvironmentHumidityHigh | 1.3.6.1.4.1.705.1.8.7.1.8 | INTEGER | read-only | Humidity is above high threshold : yes(1), no(2). |
| INT upsmgEnvironmentInput1State | 1.3.6.1.4.1.705.1.8.7.1.9 | INTEGER | read-only | State of Input#1 : closed(1), open(2). |
| INT upsmgEnvironmentInput2State | 1.3.6.1.4.1.705.1.8.7.1.10 | INTEGER | read-only | State of Input#2 : closed(1), open(2). |
| upsmgControl | 1.3.6.1.4.1.705.1.9 | |||
| upsmgControlReceptaclesTable | 1.3.6.1.4.1.705.1.9.1 | not-accessible | The table of receptacles. | |
| upsmgControlReceptaclesEntry | 1.3.6.1.4.1.705.1.9.1.1 | not-accessible | The description of a receptacle entry in the table. | |
| INT mgreceptacleIndexc | 1.3.6.1.4.1.705.1.9.1.1.1 | INTEGER | read-only | A unique value for each receptacle. Its value ranges between 1 and the value of upsmgReceptaclesNum. |
| INT mgreceptacleOnDelay | 1.3.6.1.4.1.705.1.9.1.1.2 | INTEGER | read-write | Turn on UPS receptacle w/delay=?. |
| INT mgreceptacleOnCtrl | 1.3.6.1.4.1.705.1.9.1.1.3 | INTEGER | read-write | The receptacle control on action. |
| INT mgreceptacleOnStatus | 1.3.6.1.4.1.705.1.9.1.1.4 | INTEGER | read-only | The receptacle control on status. |
| INT mgreceptacleOffDelay | 1.3.6.1.4.1.705.1.9.1.1.5 | INTEGER | read-write | Turn off UPS receptacle w/delay=?. |
| INT mgreceptacleOffCtrl | 1.3.6.1.4.1.705.1.9.1.1.6 | INTEGER | read-write | The receptacle control off action. |
| INT mgreceptacleOffStatus | 1.3.6.1.4.1.705.1.9.1.1.7 | INTEGER | read-only | The receptacle control off status. |
| INT mgreceptacleToggleDelay | 1.3.6.1.4.1.705.1.9.1.1.8 | INTEGER | read-write | Turn off then on UPS receptacle w/delay=?. |
| INT mgreceptacleToggleCtrl | 1.3.6.1.4.1.705.1.9.1.1.9 | INTEGER | read-write | The receptacle control toggle action. |
| INT mgreceptacleToggleStatus | 1.3.6.1.4.1.705.1.9.1.1.10 | INTEGER | read-only | The receptacle control toggle status. |
| INT mgreceptacleToggleDuration | 1.3.6.1.4.1.705.1.9.1.1.11 | INTEGER | read-write | Turn off then on UPS receptacle w/duration=?. |
| INT upsmgControlDayOff | 1.3.6.1.4.1.705.1.9.2 | INTEGER | read-write | The schedule off control object. Default value is none(8). Value 1 means to start scheduled off on Sunday, value 2 to start scheduled off on Monday, and so on. |
| INT upsmgControlDayOn | 1.3.6.1.4.1.705.1.9.3 | INTEGER | read-write | The schedule on control object. Default value is none(8). Value 1 means to start scheduled on on Sunday, value 2 to start scheduled on on Monday, and so on. This object is meaningfull only for those agent that do not include internal clock. In such a case the object is set by a manager to start the schedule on sequence. |
| upsmgTest | 1.3.6.1.4.1.705.1.10 | |||
| INT upsmgTestBatterySchedule | 1.3.6.1.4.1.705.1.10.1 | INTEGER | read-write | The automatic battery test schedule. |
| INT upsmgTestDiagnostics | 1.3.6.1.4.1.705.1.10.2 | INTEGER | read-write | To run self test diagnostics. |
| INT upsmgTestDiagResult | 1.3.6.1.4.1.705.1.10.3 | INTEGER | read-only | The automatic test diagnostic result. |
| INT upsmgTestBatteryCalibration | 1.3.6.1.4.1.705.1.10.4 | INTEGER | read-write | To run battery test calibration. |
| INT upsmgTestLastCalibration | 1.3.6.1.4.1.705.1.10.5 | INTEGER | read-only | The last battery calibration test date. |
| INT upsmgTestIndicators | 1.3.6.1.4.1.705.1.10.6 | INTEGER | read-write | To run UPS indicators test. |
| STR upsmgTestCommandLine | 1.3.6.1.4.1.705.1.10.7 | DisplayString | read-write | To send ASCII command line to UPS. |
| INT upsmgTestCommandReady | 1.3.6.1.4.1.705.1.10.8 | INTEGER | read-write | To advise UPS that command line has been prepared. |
| STR upsmgTestResponseLine | 1.3.6.1.4.1.705.1.10.9 | DisplayString | read-only | To get ASCII protocol response from UPS. |
| INT upsmgTestResponseReady | 1.3.6.1.4.1.705.1.10.10 | INTEGER | read-only | To advise agent that response line has been received. |
| INT upsmgTestBatteryResult | 1.3.6.1.4.1.705.1.10.11 | INTEGER | read-only | The test battery result: msuccess(1) is for manual battery test success, ssuccess(3) is for scheduled battery test success, mfailed(2) is for manual battery test failed, sfailed(4) is for scheduled battery test failed. |
| upsmgTraps | 1.3.6.1.4.1.705.1.11 | |||
| NTF upsmgBatteryFault | 1.3.6.1.4.1.705.1.11.0.1 | Trap UPS Battery entering Fault status. | ||
| NTF upsmgBatteryOK | 1.3.6.1.4.1.705.1.11.0.2 | Trap UPS Battery returned to OK status. | ||
| NTF upsmgBatteryReplacementIndicated | 1.3.6.1.4.1.705.1.11.0.3 | Trap UPS battery need to be replaced. | ||
| NTF upsmgBatteryReplaceNotIndicated | 1.3.6.1.4.1.705.1.11.0.4 | Trap UPS battery does not need to be replaced. | ||
| NTF upsmgAtLowBattery | 1.3.6.1.4.1.705.1.11.0.5 | Trap UPS battery reached low condition. | ||
| NTF upsmgFromLowBattery | 1.3.6.1.4.1.705.1.11.0.6 | Trap UPS battery returned from low condition. | ||
| NTF upsmgChargerFault | 1.3.6.1.4.1.705.1.11.0.7 | Trap UPS battery charger is not active. | ||
| NTF upsmgChargerOK | 1.3.6.1.4.1.705.1.11.0.8 | Trap UPS battery charger is active. | ||
| NTF upsmgAtLowCondition | 1.3.6.1.4.1.705.1.11.0.9 | Trap UPS entering low condition. | ||
| NTF upsmgFromLowCondition | 1.3.6.1.4.1.705.1.11.0.10 | Trap UPS exiting low condition. | ||
| NTF upsmgOnBattery | 1.3.6.1.4.1.705.1.11.0.11 | Trap UPS is on Battery. | ||
| NTF upsmgReturnFromBattery | 1.3.6.1.4.1.705.1.11.0.12 | Trap UPS returned from battery. | ||
| NTF upsmgOnByPass | 1.3.6.1.4.1.705.1.11.0.13 | Trap UPS is on by pass. | ||
| NTF upsmgReturnFromByPass | 1.3.6.1.4.1.705.1.11.0.14 | Trap UPS return from by pass. | ||
| NTF upsmgByPassUnavailable | 1.3.6.1.4.1.705.1.11.0.15 | Trap UPS by pass unavailable. | ||
| NTF upsmgByPassAvailable | 1.3.6.1.4.1.705.1.11.0.16 | Trap UPS by pass available. | ||
| NTF upsmgUtilityFailure | 1.3.6.1.4.1.705.1.11.0.17 | Trap UPS utility power failed. | ||
| NTF upsmgUtilityRestored | 1.3.6.1.4.1.705.1.11.0.18 | Trap UPS utility power restored. | ||
| NTF upsmgOnBoost | 1.3.6.1.4.1.705.1.11.0.19 | Trap UPS is on boost. | ||
| NTF upsmgReturnFromBoost | 1.3.6.1.4.1.705.1.11.0.20 | Trap UPS has returned from boost. | ||
| NTF upsmgOverLoad | 1.3.6.1.4.1.705.1.11.0.21 | Trap UPS has overload condition. | ||
| NTF upsmgLoadOK | 1.3.6.1.4.1.705.1.11.0.22 | Trap UPS quit overload condition. | ||
| NTF upsmgOverTemperature | 1.3.6.1.4.1.705.1.11.0.23 | Trap UPS has overtemperature condition. | ||
| NTF upsmgTemperatureOK | 1.3.6.1.4.1.705.1.11.0.24 | Trap UPS quit overtemperature condition. | ||
| NTF upsmgOnToStart | 1.3.6.1.4.1.705.1.11.0.25 | Trap UPS on sequence started. | ||
| NTF upsmgOnAbort | 1.3.6.1.4.1.705.1.11.0.26 | Trap UPS on sequence cancelled. | ||
| NTF upsmgOnInProgress | 1.3.6.1.4.1.705.1.11.0.27 | Trap UPS on sequence in progress in ups. | ||
| NTF upsmgOnComplete | 1.3.6.1.4.1.705.1.11.0.28 | Trap UPS on sequence completed. | ||
| NTF upsmgOffToStart | 1.3.6.1.4.1.705.1.11.0.29 | Trap UPS off sequence started. | ||
| NTF upsmgOffAbort | 1.3.6.1.4.1.705.1.11.0.30 | Trap UPS off sequence cancelled. | ||
| NTF upsmgOffInProgress | 1.3.6.1.4.1.705.1.11.0.31 | Trap UPS off sequence in progress in ups. | ||
| NTF upsmgOffComplete | 1.3.6.1.4.1.705.1.11.0.32 | Trap UPS off sequence completed. | ||
| NTF upsmgToggleToStart | 1.3.6.1.4.1.705.1.11.0.33 | Trap UPS toggle (off/on) sequence started. | ||
| NTF upsmgToggleAbort | 1.3.6.1.4.1.705.1.11.0.34 | Trap UPS toggle (off/on) sequence cancelled. | ||
| NTF upsmgToggleInProgress | 1.3.6.1.4.1.705.1.11.0.35 | Trap UPS toggle (off/on) sequence in progress in ups. | ||
| NTF upsmgToggleComplete | 1.3.6.1.4.1.705.1.11.0.36 | Trap UPS toggle (off/on) sequence completed. | ||
| NTF upsmgCommunicationFailure | 1.3.6.1.4.1.705.1.11.0.37 | Trap UPS serial communication failed. | ||
| NTF upsmgCommunicationRestored | 1.3.6.1.4.1.705.1.11.0.38 | Trap UPS serial communication restored. | ||
| NTF upsmgInputBad | 1.3.6.1.4.1.705.1.11.0.39 | Trap UPS input has bad condition. | ||
| NTF upsmgInputOK | 1.3.6.1.4.1.705.1.11.0.40 | Trap UPS input quit bad condition. | ||
| NTF upsmgBatteryUnavailable | 1.3.6.1.4.1.705.1.11.0.41 | Trap UPS battery is unavailable. | ||
| NTF upsmgBatteryAvailable | 1.3.6.1.4.1.705.1.11.0.42 | Trap UPS battery return from unavailable condition. | ||
| NTF upsmgAtLowRecharge | 1.3.6.1.4.1.705.1.11.0.43 | Trap UPS waiting for battery charging condition. | ||
| NTF upsmgFromLowRecharge | 1.3.6.1.4.1.705.1.11.0.44 | Trap UPS reached battery charging condition. | ||
| NTF upsmgDiagnosticTestFail | 1.3.6.1.4.1.705.1.11.0.45 | Trap UPS self test failed. | ||
| NTF upsmgDiagnosticTestOK | 1.3.6.1.4.1.705.1.11.0.46 | Trap UPS self test succeeded. | ||
| NTF upsmgBatteryTestOK | 1.3.6.1.4.1.705.1.11.0.47 | Trap UPS passed battery test. | ||
| NTF upsmgBatteryTestFail | 1.3.6.1.4.1.705.1.11.0.48 | Trap UPS failed battery test. | ||
| NTF upsmgExternalAlarmActive | 1.3.6.1.4.1.705.1.11.0.49 | Trap UPS enter environment external alarm. | ||
| NTF upsmgExternalAlarmInactive | 1.3.6.1.4.1.705.1.11.0.50 | Trap UPS exit environment external alarm. | ||
| NTF upsmgOnBuck | 1.3.6.1.4.1.705.1.11.0.51 | Trap UPS is on buck. | ||
| NTF upsmgReturnFromBuck | 1.3.6.1.4.1.705.1.11.0.52 | Trap UPS has returned from buck. | ||
| NTF upsmgEnvironComFailure | 1.3.6.1.4.1.705.1.11.0.53 | Environment Probe communication failure. | ||
| NTF upsmgEnvironComOK | 1.3.6.1.4.1.705.1.11.0.54 | Environment Probe communication restored. | ||
| NTF upsmgEnvironTemperatureLow | 1.3.6.1.4.1.705.1.11.0.55 | Temperature is below low threshold. | ||
| NTF upsmgEnvironTemperatureHigh | 1.3.6.1.4.1.705.1.11.0.56 | Temperature is above high threshold. | ||
| NTF upsmgEnvironTemperatureOK | 1.3.6.1.4.1.705.1.11.0.57 | Temperature is in normal range. | ||
| NTF upsmgEnvironHumidityLow | 1.3.6.1.4.1.705.1.11.0.58 | Humidity is below low threshold. | ||
| NTF upsmgEnvironHumidityHigh | 1.3.6.1.4.1.705.1.11.0.59 | Humidity is above high threshold. | ||
| NTF upsmgEnvironHumidityOK | 1.3.6.1.4.1.705.1.11.0.60 | Humidity is in normal range. | ||
| NTF upsmgEnvironInput1Closed | 1.3.6.1.4.1.705.1.11.0.61 | Input #1 is Closed. | ||
| NTF upsmgEnvironInput1Open | 1.3.6.1.4.1.705.1.11.0.62 | Input #1 is Open. | ||
| NTF upsmgEnvironInput2Closed | 1.3.6.1.4.1.705.1.11.0.63 | Input #2 is Closed. | ||
| NTF upsmgEnvironInput2Open | 1.3.6.1.4.1.705.1.11.0.64 | Input #2 is Open. | ||
| upsmgAgent | 1.3.6.1.4.1.705.1.12 | |||
| IP upsmgAgentIpaddress | 1.3.6.1.4.1.705.1.12.1 | IpAddress | read-write | The ip address that NMS can identify the managed device |
| IP upsmgAgentSubnetMask | 1.3.6.1.4.1.705.1.12.2 | IpAddress | read-write | Internet address subnet mask |
| IP upsmgAgentDefGateway | 1.3.6.1.4.1.705.1.12.3 | IpAddress | read-write | The default gateway that allow device managed through routers |
| INT upsmgAgentBaudRate | 1.3.6.1.4.1.705.1.12.4 | INTEGER | read-write | the serial port communication speed. only 2400, 4800, and 9600 allowed |
| INT upsmgAgentPollRate | 1.3.6.1.4.1.705.1.12.5 | INTEGER | read-write | The frequency that proxy agent polls the connected UPS in ASCII protocol. (unit : second) |
| INT upsmgAgentType | 1.3.6.1.4.1.705.1.12.6 | INTEGER | read-write | The type of agent. |
| INT upsmgAgentTrapAlarmDelay | 1.3.6.1.4.1.705.1.12.7 | INTEGER | read-write | The interval for the Trap packet retransmission, while the TRAP Acknowledge is implemented and the ack is received within the interval. |
| INT upsmgAgentTrapAlarmRetry | 1.3.6.1.4.1.705.1.12.8 | INTEGER | read-write | The retry count for retransmitting Trap packet while the TRAP acknowledge is implemented. |
| INT upsmgAgentReset | 1.3.6.1.4.1.705.1.12.9 | INTEGER | read-write | The variable initiates reset operation in agent software, ie. warm start. write reset(1) to any one of UPS MIB array, will result in the same reset operation. |
| INT upsmgAgentFactReset | 1.3.6.1.4.1.705.1.12.10 | INTEGER | read-write | The variable initiates reset operation in agent software, ie. warm start, and load default data (Factory setting) to EEPROM and to runtime parameters associated with the UPS. |
| INT upsmgAgentMibVersion | 1.3.6.1.4.1.705.1.12.11 | INTEGER | read-only | The version of the MIB implemented in agent. |
| STR upsmgAgentFirmwareVersion | 1.3.6.1.4.1.705.1.12.12 | DisplayString | read-only | The agent firmware version. |
| INT upsmgAgentCommUPS | 1.3.6.1.4.1.705.1.12.13 | INTEGER | read-only | The status of communication between agent and ups. Even value means no communication, and odd value means a certain level of communication with devices daisy-chained on the serial port. The value is the following: 1000*NSE + 100*NSW + 10*UPSW + UPST with UPST is UPS type: 5 if no UPS; 3 if PI (Protocol Interface) 1 if U-Talk UPS; UPSW is the number of switchable plugs of the UPS; NSW is the number of UM-Switch devices; NSE is the number of UM-Sensor devices. |
| INT upsmgAgentTrapAck | 1.3.6.1.4.1.705.1.12.14 | INTEGER | read-write | The last Trap number that has been received by UM-View. |
| INT upsmgAgentAutoLearning | 1.3.6.1.4.1.705.1.12.15 | INTEGER | read-write | The enabled/disabled configuration of the Auto Learning process of the agent, default value is yes(1) e.g. enabled. |
| INT upsmgAgentBootP | 1.3.6.1.4.1.705.1.12.16 | INTEGER | read-write | The enabled/disabled configuration of the BootP process, default value is yes(1) e.g. enabled. |
| INT upsmgAgentTFTP | 1.3.6.1.4.1.705.1.12.17 | INTEGER | read-write | The enabled/disabled configuration of the TFTP process, default value is no(2) e.g. disabled. |
| INT upsmgAgentTrapSignature | 1.3.6.1.4.1.705.1.12.18 | INTEGER | read-only | The signature of the trap acknowledged by a manager. |
| upsmgRemote | 1.3.6.1.4.1.705.1.13 | |||
| INT upsmgRemoteOnBattery | 1.3.6.1.4.1.705.1.13.1 | INTEGER | read-write | An object to inform an ups-less agent that the remote UPS is on autonomy. This object could be set by a management application. |
| IP upsmgRemoteIpAddress | 1.3.6.1.4.1.705.1.13.2 | IpAddress | read-write | An object to give the IP address of the agent managing the remote UPS. This object could be read by managers to perform management of receptacle dependencies between two different agents. |
RFC description
Monitors UPS battery status, load, and power events for Minuteman/Para Systems UPS units.
Start monitoring Minuteman/Para Systems UPS units with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.