CYCLADES-ACS5K-PM-MIB

All MIBs › CYCLADES-ACS5K-PM-MIB

Organization: Avocent Corporation

Last Updated: 2010-07-26

Category: Power Management

Description: Manages power outlet switching and monitoring on Avocent Cyclades ACS 5000 power modules.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CYCLADES-ACS5K-PM-MIB?

This is a power-module (PM) proxy MIB for the Avocent Cyclades ACS 5000 console server platform, managing switched power-distribution units attached via serial port. It exposes inventory/configuration data (number of outlets, units, firmware version) plus a control object (cyPMCommand) and current-draw reading (cyPMCurrent). Monitoring emphasis is on hardware status of the attached PDU: cyPMCurrent reveals abnormal power draw, cyPMVersion tracks PM firmware, and per-unit/outlet tables let an operator confirm all outlet units are reporting and available for remote power-cycling. Being a proxy MIB, it depends on the ACS 5000's serial-attached PM hardware protocol rather than a standard IETF MIB. Deployment context is Avocent Cyclades ACS 5000 console servers with attached switched PDUs in data-center racks, and the CYCLADES-ACS5K-PM-MIB MIB provides the object definitions administrators use to monitor those power modules.

IPNetwork Monitor allows you to monitor SNMP objects defined in CYCLADES-ACS5K-PM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Avocent Cyclades ACS 5000 console server with attached power distribution unit (PDU)

Monitoring Examples

Poll cyPMTable (indexed by cyPMSerialPortNumber) for cyPMCurrent to detect a rack PDU drawing abnormal current, and check cyPMUnitTable (cyPMUnitNumber) alongside cyPMNumberOutlets to confirm all outlet units are reporting. cyPMCommand can be SET to remote-cycle a stuck outlet identified through this monitoring.

What Can Be Monitored

PDU current draw
number of outlets/units
PM firmware version
per-outlet power state (via command/status)

Imported Objects

From CYCLADES-ACS5K-MIB

cyACS5KMgmt

MODULE-IDENTITY

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString

How to Use in IPNetwork Monitor

Example using cyNumberOfPM OID:

Select an Avocent Cyclades ACS 5000 console server (attached PDU) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cyNumberOfPM into the Find box to locate it in the OID tree, then select it and click OK. The total number of PM's connected on the unit. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an Integer32-type OID, Value bounds is the most useful condition here — trigger an alert if the count changes from its expected baseline, since that would indicate the underlying set of items changed unexpectedly. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
cyACS5KPM	1.3.6.1.4.1.2925.8.5			This module defines objects of the Proxy for PM
I32 cyNumberOfPMEx	1.3.6.1.4.1.2925.8.5.1	Integer32	read-only	The total number of PM's connected on the unit
cyPMTable	1.3.6.1.4.1.2925.8.5.2		not-accessible	Allows to read information about each connected PM
cyPMEntry	1.3.6.1.4.1.2925.8.5.2.1		not-accessible	Information about the connected PM
NUM cyPMSerialPortNumber	1.3.6.1.4.1.2925.8.5.2.1.1	InterfaceIndex	read-only	The number of the serial port when the PM is connected.
I32 cyPMNumberOutlets	1.3.6.1.4.1.2925.8.5.2.1.2	Integer32	read-only	Number of outlets.
I32 cyPMNumberUnits	1.3.6.1.4.1.2925.8.5.2.1.3	Integer32	read-only	Total number of PM unists that are accessed by this serial port.
STR cyPMCurrent	1.3.6.1.4.1.2925.8.5.2.1.4	DisplayString	read-only	Current reading for the PM.
STR cyPMVersion	1.3.6.1.4.1.2925.8.5.2.1.5	DisplayString	read-only	The software version of the PM.
STR cyPMCommand	1.3.6.1.4.1.2925.8.5.2.1.7	DisplayString	read-write	A character string for the user to send commands to PM. He can use it to does the save command. Or to list the outlets that need to be turned off, or turned on , or cycled or locked or unlocked as a group. The command is the first word and is followed by a space and the outlet list (otulets commands). Valid commands are 'on', 'off', 'cycle', 'lock', 'unlock', 'save'.
cyPMUnitTable	1.3.6.1.4.1.2925.8.5.3		not-accessible	Allow operations on specific PM unit connected
cyPMUnitEntry	1.3.6.1.4.1.2925.8.5.3.1		not-accessible	Allow operations on outlet
NUM cyPMUnitNumber	1.3.6.1.4.1.2925.8.5.3.1.1	InterfaceIndex	not-accessible	The number of the PM unit in the daisy-chained mode.
STR cyPMUnitVersion	1.3.6.1.4.1.2925.8.5.3.1.2	DisplayString	read-only	The software version of this PM unit.
I32 cyPMUnitOutlets	1.3.6.1.4.1.2925.8.5.3.1.3	Integer32	read-only	Number of outlets of this PM unit.
I32 cyPMUnitFirstOutlet	1.3.6.1.4.1.2925.8.5.3.1.4	Integer32	read-only	Number of the first outlet of this PM unit.
I32 cyPMUnitCurrent	1.3.6.1.4.1.2925.8.5.3.1.5	Integer32	read-only	Current of this PM unit in AMP. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.)
I32 cyPMUnitMaxCurrent	1.3.6.1.4.1.2925.8.5.3.1.6	Integer32	read-only	Maximum current of this PM unit in AMP. The value of this object is the maximum current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the maximum current is 0.5 AMP.)
I32 cyPMUnitSequenceInterval	1.3.6.1.4.1.2925.8.5.3.1.9	Integer32	read-only	Sequence interval delay. Valid values are 2 to 15 (seconds).
I32 cyPMUnitCycleInterval	1.3.6.1.4.1.2925.8.5.3.1.10	Integer32	read-only	Number of seconds that a socket stays off before turning it back on.
STR cyPMUnitID	1.3.6.1.4.1.2925.8.5.3.1.11	DisplayString	read-only	PDU identification.
INT cyPMUnitPhases	1.3.6.1.4.1.2925.8.5.3.1.12	INTEGER	read-only	Number of phases of this PDU unit.
I32 cyPMUnitBanks	1.3.6.1.4.1.2925.8.5.3.1.13	Integer32	read-only	Number of banks of this PDU unit.
I32 cyPMUnitNominalVoltage	1.3.6.1.4.1.2925.8.5.3.1.14	Integer32	read-only	Nominal Voltage configured for this PDU unit, when it does not have voltage sensor
I32 cyPMUnitPower	1.3.6.1.4.1.2925.8.5.3.1.15	Integer32	read-only	Power Consumption of this PDU unit (it is estimated when PDU does not have voltage sensor).
cyOutletTable	1.3.6.1.4.1.2925.8.5.4		not-accessible	Allow operations on outlet
cyOutletEntry	1.3.6.1.4.1.2925.8.5.4.1		not-accessible	Allow operations on outlet
NUM cyOutletNumber	1.3.6.1.4.1.2925.8.5.4.1.1	InterfaceIndexOrZero	not-accessible	The outlet number on the PM. Zero is ALL outlets.
STR cyOutletName	1.3.6.1.4.1.2925.8.5.4.1.2	DisplayString	read-write	The name given to a particular outlet Maximum size is 8 characters.
STR cyOutletServer	1.3.6.1.4.1.2925.8.5.4.1.3	DisplayString	read-only	Alias of the Server connected to this outlet .
INT cyOutletPower	1.3.6.1.4.1.2925.8.5.4.1.4	INTEGER	read-write	Getting this object will return the power state of the outlet. Valid return states are UNKNOW, OFF and ON. Setting this object will change the power state of the outlet.
INT cyOutletLock	1.3.6.1.4.1.2925.8.5.4.1.5	INTEGER	read-write	Getting this object will return the lock state of the outlet. Setting this object will change the lock state of the outlet.
I32 cyOutletPUInterval	1.3.6.1.4.1.2925.8.5.4.1.6	Integer32	read-write	The power unit interval of this outlet in seconds. The value of this object is the actual interval in seconds * 10. You need to translate the readed value (Ex. : value is 5, the interval is 0.5 seconds.)
I32 cyOutletMinimumOnInterval	1.3.6.1.4.1.2925.8.5.4.1.7	Integer32	read-only	Minimum time in seconds an outlet will stay on before turning it off.
I32 cyOutletMinimumOffInterval	1.3.6.1.4.1.2925.8.5.4.1.8	Integer32	read-only	Minimum time in seconds an outlet will stay off before turning it on.
I32 cyOutletWakeupState	1.3.6.1.4.1.2925.8.5.4.1.9	Integer32	read-only	Outlet state after a cold boot. It can be set to on or off.
STR cyOutletPduID	1.3.6.1.4.1.2925.8.5.4.1.10	DisplayString	read-only	PDU identification.
I32 cyOutletPduNumber	1.3.6.1.4.1.2925.8.5.4.1.11	Integer32	not-accessible	The number of the PDU unit in the daisy-chained mode.
cyPMElecPduTable	1.3.6.1.4.1.2925.8.5.5		not-accessible	Allow operations on elecmon element of the PDUs
cyPMElecPduTableEntry	1.3.6.1.4.1.2925.8.5.5.1		not-accessible	each entry has the information about the elecmon element of the PDUs.
NUM cyPMElecPduTablePortNumber	1.3.6.1.4.1.2925.8.5.5.1.1	InterfaceIndex	read-only	Serial Port number where the PDU is connected.
NUM cyPMElecPduTablePduNumber	1.3.6.1.4.1.2925.8.5.5.1.2	InterfaceIndex	read-only	The number of the PDU unit in the daisy-chained mode
I32 cyPMElecPduTableCurrentValue	1.3.6.1.4.1.2925.8.5.5.1.3	Integer32	read-only	Actual value of current in the element (A x 10).
I32 cyPMElecPduTableCurrentMax	1.3.6.1.4.1.2925.8.5.5.1.4	Integer32	read-write	Maximum detected value of current in the element (A x 10). Write operation accepts only 0 for reset action.
I32 cyPMElecPduTablePowerValue	1.3.6.1.4.1.2925.8.5.5.1.5	Integer32	read-only	Actual value of power in the element (W x 10).
I32 cyPMElecPduTablePowerMax	1.3.6.1.4.1.2925.8.5.5.1.6	Integer32	read-write	Maximum value of power in the element (W x 10). Write operation accepts only 0 for reset action.
I32 cyPMElecPduTableVoltageValue	1.3.6.1.4.1.2925.8.5.5.1.7	Integer32	read-only	Actual value of voltage in the element (V).When element does not have voltage sensor, it returns 0.
I32 cyPMElecPduTableVoltageMax	1.3.6.1.4.1.2925.8.5.5.1.8	Integer32	read-write	Maximum value of voltage in the element (V). When element does not have voltage sensor, it returns 0. Write operation accepts only 0 for reset action.
I32 cyPMElecPduTablePowerFactorValue	1.3.6.1.4.1.2925.8.5.5.1.9	Integer32	read-only	Actual value of power factor in the element (Pf x 10). When element does not have power factor sensor, returns 0.
I32 cyPMElecPduTablePowerFactorMax	1.3.6.1.4.1.2925.8.5.5.1.10	Integer32	read-write	Maximum value of power factor in the element (Pf x 10). When element does not have power factor sensor, returns 0. Write operation accepts only 0 for reset action.
INT cyPMElecPduTablePowerType	1.3.6.1.4.1.2925.8.5.5.1.11	INTEGER	read-only	This PDU unit's Power sensor type.
INT cyPMElecPduTableVoltageType	1.3.6.1.4.1.2925.8.5.5.1.12	INTEGER	read-only	This PDU unit's has voltage sensor type.
INT cyPMElecPduTablePowerFactorType	1.3.6.1.4.1.2925.8.5.5.1.13	INTEGER	read-only	This PDU unit's Power Factor sensor type.
cyPMElecPhaseTable	1.3.6.1.4.1.2925.8.5.6		not-accessible	Allow operations on elecmon element for phases
cyPMElecPhaseTableEntry	1.3.6.1.4.1.2925.8.5.6.1		not-accessible	each entry has the information about the elecmon for phase.
NUM cyPMElecPhaseTablePortNumber	1.3.6.1.4.1.2925.8.5.6.1.1	InterfaceIndex	read-only	Serial Port number where the PDU is connected.
NUM cyPMElecPhaseTablePduNumber	1.3.6.1.4.1.2925.8.5.6.1.2	InterfaceIndex	read-only	The number of the PDU unit in the daisy-chained mode
NUM cyPMElecPhaseTableIndex	1.3.6.1.4.1.2925.8.5.6.1.3	InterfaceIndex	read-only	index of the phase in the PDU. Index can be 1,2 or 3.
STR cyPMElecPhaseTableName	1.3.6.1.4.1.2925.8.5.6.1.4	DisplayString	read-only	Sys-name of the phase.
I32 cyPMElecPhaseTableCurrentValue	1.3.6.1.4.1.2925.8.5.6.1.5	Integer32	read-only	Actual value of current in the phase (A x 10).
I32 cyPMElecPhaseTableCurrentMax	1.3.6.1.4.1.2925.8.5.6.1.6	Integer32	read-write	Maximum detected value of current in the phase (A x 10). Write operation accepts only 0 for reset action.
I32 cyPMElecPhaseTablePowerValue	1.3.6.1.4.1.2925.8.5.6.1.7	Integer32	read-only	Actual value of power in the phase (W x 10).
I32 cyPMElecPhaseTablePowerMax	1.3.6.1.4.1.2925.8.5.6.1.8	Integer32	read-write	Maximum value of power in the phase (W x 10).Write operation accepts only 0 for reset action.
I32 cyPMElecPhaseTableVoltageValue	1.3.6.1.4.1.2925.8.5.6.1.9	Integer32	read-only	Actual value of voltage in the phase (V).When phase does not have voltage sensor, it returns 0.
I32 cyPMElecPhaseTableVoltageMax	1.3.6.1.4.1.2925.8.5.6.1.10	Integer32	read-write	Maximum value of voltage in the phase (V). When phase does not have voltage sensor, it returns 0. Write operation accepts only 0 for reset action.
I32 cyPMElecPhaseTablePowerFactorValue	1.3.6.1.4.1.2925.8.5.6.1.11	Integer32	read-only	Actual value of power factor in the phase (Pf x 10). When phase does not have power factor sensor, returns 0.
I32 cyPMElecPhaseTablePowerFactorMax	1.3.6.1.4.1.2925.8.5.6.1.12	Integer32	read-write	Maximum value of power factor in the phase (Pf x 10). When phase does not have power factor sensor, returns 0.Write operation accepts only 0 for reset action.
INT cyPMElecPhaseTablePowerType	1.3.6.1.4.1.2925.8.5.6.1.13	INTEGER	read-only	The type of Power sensor for this elecmon
INT cyPMElecPhaseTableVoltageType	1.3.6.1.4.1.2925.8.5.6.1.14	INTEGER	read-only	The type of Voltage sensor for this elecmon
INT cyPMElecPhaseTablePowerFactorType	1.3.6.1.4.1.2925.8.5.6.1.15	INTEGER	read-only	The type of Power Factor sensor for this elecmon
cyPMElecBankTable	1.3.6.1.4.1.2925.8.5.7		not-accessible	Allow operations on elecmon element for banks
cyPMElecBankTableEntry	1.3.6.1.4.1.2925.8.5.7.1		not-accessible	each entry has the information about the elecmon for Bank.
NUM cyPMElecBankTablePortNumber	1.3.6.1.4.1.2925.8.5.7.1.1	InterfaceIndex	read-only	Serial Port number where the PDU is connected.
NUM cyPMElecBankTablePduNumber	1.3.6.1.4.1.2925.8.5.7.1.2	InterfaceIndex	read-only	The number of the PDU unit in the daisy-chained mode
NUM cyPMElecBankTableIndex	1.3.6.1.4.1.2925.8.5.7.1.3	InterfaceIndex	read-only	index of the Bank in the PDU. Index can be 1,2, ... number of banks of the PDU.
STR cyPMElecBankTableName	1.3.6.1.4.1.2925.8.5.7.1.4	DisplayString	read-only	Sys-name of the Bank.
I32 cyPMElecBankTableCurrentValue	1.3.6.1.4.1.2925.8.5.7.1.5	Integer32	read-only	Actual value of current in the Bank (A x 10).
I32 cyPMElecBankTableCurrentMax	1.3.6.1.4.1.2925.8.5.7.1.6	Integer32	read-write	Maximum detected value of current in the Bank (A x 10). Write operation accepts only 0 for reset action.
I32 cyPMElecBankTablePowerValue	1.3.6.1.4.1.2925.8.5.7.1.7	Integer32	read-only	Actual value of power in the Bank (W x 10).
I32 cyPMElecBankTablePowerMax	1.3.6.1.4.1.2925.8.5.7.1.8	Integer32	read-write	Maximum value of power in the Bank (W x 10).Write operation accepts only 0 for reset action.
I32 cyPMElecBankTableVoltageValue	1.3.6.1.4.1.2925.8.5.7.1.9	Integer32	read-only	Actual value of voltage in the Bank (V).When Bank does not have voltage sensor, it returns 0.
I32 cyPMElecBankTableVoltageMax	1.3.6.1.4.1.2925.8.5.7.1.10	Integer32	read-write	Maximum value of voltage in the Bank (V). When Bank does not have voltage sensor, it returns 0. Write operation accepts only 0 for reset action.
I32 cyPMElecBankTablePowerFactorValue	1.3.6.1.4.1.2925.8.5.7.1.11	Integer32	read-only	Actual value of power factor in the Bank (Pf x 10). When Bank does not have power factor sensor, returns 0.
I32 cyPMElecBankTablePowerFactorMax	1.3.6.1.4.1.2925.8.5.7.1.12	Integer32	read-write	Maximum value of power factor in the Bank (Pf x 10). When Bank does not have power factor sensor, returns 0.Write operation accepts only 0 for reset action.
INT cyPMElecBankTablePowerType	1.3.6.1.4.1.2925.8.5.7.1.13	INTEGER	read-only	The type of Power sensor for this elecmon
INT cyPMElecBankTableVoltageType	1.3.6.1.4.1.2925.8.5.7.1.14	INTEGER	read-only	The type of Voltage sensor for this elecmon
INT cyPMElecBankTablePowerFactorType	1.3.6.1.4.1.2925.8.5.7.1.15	INTEGER	read-only	The type of Power Factor sensor for this elecmon
cyPMElecOutletTable	1.3.6.1.4.1.2925.8.5.8		not-accessible	Allow operations on elecmon element for outlets
cyPMElecOutletTableEntry	1.3.6.1.4.1.2925.8.5.8.1		not-accessible	each entry has the information about the elecmon for Outlet.
NUM cyPMElecOutletTablePortNumber	1.3.6.1.4.1.2925.8.5.8.1.1	InterfaceIndex	read-only	Serial Port number where the PDU is connected.
NUM cyPMElecOutletTablePduNumber	1.3.6.1.4.1.2925.8.5.8.1.2	InterfaceIndex	read-only	The number of the PDU unit in the daisy-chained mode
NUM cyPMElecOutletTableNumber	1.3.6.1.4.1.2925.8.5.8.1.3	InterfaceIndex	read-only	outlet number in the PDU
STR cyPMElecOutletTableName	1.3.6.1.4.1.2925.8.5.8.1.4	DisplayString	read-only	name of the Outlet.
I32 cyPMElecOutletTableCurrentValue	1.3.6.1.4.1.2925.8.5.8.1.5	Integer32	read-only	Actual value of current in the Outlet (A x 10).
I32 cyPMElecOutletTableCurrentMax	1.3.6.1.4.1.2925.8.5.8.1.6	Integer32	read-write	Maximum detected value of current in the Outlet (A x 10). Write operation accepts only 0 for reset action.
I32 cyPMElecOutletTablePowerValue	1.3.6.1.4.1.2925.8.5.8.1.7	Integer32	read-only	Actual value of power in the Outlet (W x 10).
I32 cyPMElecOutletTablePowerMax	1.3.6.1.4.1.2925.8.5.8.1.8	Integer32	read-write	Maximum value of power in the Outlet (W x 10).Write operation accepts only 0 for reset action.
I32 cyPMElecOutletTableVoltageValue	1.3.6.1.4.1.2925.8.5.8.1.9	Integer32	read-only	Actual value of voltage in the Outlet (V).When Outlet does not have voltage sensor, it returns 0.
I32 cyPMElecOutletTableVoltageMax	1.3.6.1.4.1.2925.8.5.8.1.10	Integer32	read-write	Maximum value of voltage in the Outlet (V). When Outlet does not have voltage sensor, it returns 0. Write operation accepts only 0 for reset action.
I32 cyPMElecOutletTablePowerFactorValue	1.3.6.1.4.1.2925.8.5.8.1.11	Integer32	read-only	Actual value of power factor in the Outlet (Pf x 10). When Outlet does not have power factor sensor, returns 0.
I32 cyPMElecOutletTablePowerFactorMax	1.3.6.1.4.1.2925.8.5.8.1.12	Integer32	read-write	Maximum value of power factor in the Outlet (Pf x 10). When Outlet does not have power factor sensor, returns 0.Write operation accepts only 0 for reset action.
INT cyPMElecOutletTablePowerType	1.3.6.1.4.1.2925.8.5.8.1.13	INTEGER	read-only	The type of Power sensor for this elecmon
INT cyPMElecOutletTableVoltageType	1.3.6.1.4.1.2925.8.5.8.1.14	INTEGER	read-only	The type of Voltage sensor for this elecmon
INT cyPMElecOutletTablePowerFactorType	1.3.6.1.4.1.2925.8.5.8.1.15	INTEGER	read-only	The type of Power Factor sensor for this elecmon
cyPMEnvMonTable	1.3.6.1.4.1.2925.8.5.9		not-accessible	Allow operations on environmental monitors
cyPMEnvMonTableEntry	1.3.6.1.4.1.2925.8.5.9.1		not-accessible	each entry has the information about the environmental monitors.
NUM cyPMEnvMonTablePortNumber	1.3.6.1.4.1.2925.8.5.9.1.1	InterfaceIndex	read-only	Serial Port number where the PDU is connected.
NUM cyPMEnvMonTablePduNumber	1.3.6.1.4.1.2925.8.5.9.1.2	InterfaceIndex	read-only	The number of the PDU unit in the daisy-chained mode
NUM cyPMEnvMonTableIndex	1.3.6.1.4.1.2925.8.5.9.1.3	InterfaceIndex	read-only	index of the environmental monitor in the PDU.
STR cyPMEnvMonTableName	1.3.6.1.4.1.2925.8.5.9.1.4	DisplayString	read-only	Name of the environmental monitor.
INT cyPMEnvMonTableType	1.3.6.1.4.1.2925.8.5.9.1.5	INTEGER	read-only	The type of environmental monitor.
INT cyPMEnvMonTableStatus	1.3.6.1.4.1.2925.8.5.9.1.6	INTEGER	read-only	The status of Dry-Contact/Water-level/Smoke/Motion monitors. Dry-Contact sensor: Opened(1), closed(2). Water level: Normal (1), Triggered(2). Smoke sensor: not-detected(1), detected(2). Motion sensor: not-detected(1), detected(2).
I32 cyPMEnvMonTableValue	1.3.6.1.4.1.2925.8.5.9.1.7	Integer32	read-only	Actual value of Temperature/Humidity/Air-flow monitors (x 10).
I32 cyPMEnvMonTableMaxValue	1.3.6.1.4.1.2925.8.5.9.1.8	Integer32	read-write	Maximum detected value of Temperature/Humidity/Air-flow monitor (x 10). Write operation accepts only 0 for reset action.

RFC description

Avocent Cyclades ACS 5000 power management MIB for monitoring power modules and system power state (vendor-private).

Start monitoring Avocent Cyclades ACS 5000 console server (attached PDU) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CYCLADES-ACS5K-PM-MIB