ME1200-ACL-MIB

All MIBs › ME1200-ACL-MIB

Organization: Cisco Systems, Inc

Last Updated: 2014-03-11

Category: Domain: Security, Vendor: Cisco

Description: Cisco ME1200 Metro Ethernet switch MIB defining access control list (ACL) rules and policy configuration objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ME1200-ACL-MIB?

This is a Cisco private MIB for the ME1200 Metro Ethernet access switch, defining access control list (ACL) rules, rate limiters, and ingress port policy configuration. It exposes tables for ACL access control entries (ACEs), their lookup order and next-ACE chaining, ingress port lists, and rate limiter definitions specifying packet-rate and bit-rate limits. Its monitoring value is around configuration/policy state—verifying which ACL rules and rate limiters are active on which ports, and catching misconfigured or unexpectedly disabled filtering policies—rather than hardware sensor data, since ACL processing is a switch software/forwarding-plane function. It is a vendor-private MIB specific to the ME1200 platform with no strong dependency on external standard MIBs evident from the object set. Typical deployment is on Cisco ME1200 Metro Ethernet switches used by service providers for Carrier Ethernet access and aggregation. Engineers can download the ME1200-ACL-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ME1200-ACL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco ME1200 Metro Ethernet access switch

Monitoring Examples

An operator would walk me1200AclAceTable, keyed by me1200AclAceId, to confirm the expected ACE rules are present and check me1200AclAceIngressPortList to verify which physical ports a rule applies to, along with me1200AclAceLookup to understand the match criteria in use. The me1200AclRateLimiterTable lets an admin confirm a given me1200AclRateLimiterId enforces the intended me1200AclRateLimiterPacketRate or me1200AclRateLimiterBitRate (when me1200AclRateLimiterBitRateEnable is set), catching cases where a rate limiter is misapplied and causing unexpected traffic drops. Chained rules can be traced via me1200AclAceNextAceId to validate the overall ACL processing order.

What Can Be Monitored

active ACL rules per port
ACE match/lookup criteria
rate limiter packet/bit rate settings
ingress port list per ACL rule

Imported Objects

From CISCOME1200-MIB

me1200SwitchMgmt

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddressIPv6

From ME1200-TC

ME1200InterfaceIndex
ME1200PortList
ME1200RowEditorState
ME1200Unsigned16
ME1200Unsigned8

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
me1200AclMIB	1.3.6.1.4.1.9.9.815.1.17			This is a private MIB for ACL
me1200AclMIBObjects	1.3.6.1.4.1.9.9.815.1.17.1
me1200AclConfig	1.3.6.1.4.1.9.9.815.1.17.1.2
me1200AclGlobals	1.3.6.1.4.1.9.9.815.1.17.1.2.1
me1200AclRateLimiterTable	1.3.6.1.4.1.9.9.815.1.17.1.2.1.1		not-accessible	The ACL rate limiter configuration table.
me1200AclRateLimiterEntry	1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1		not-accessible	Each rate limiter ID has a set of parameters
I32 me1200AclRateLimiterId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.1	Integer32	not-accessible	The identification of ACL rate limter.
U32 me1200AclRateLimiterPacketRate	1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.2	Unsigned32	read-write	The packet rate per second. The operation is inactive when bit rate mode is enabled. Possible values are: 0-99, 100, 2100, 3100..., 1092000.
U32 me1200AclRateLimiterBitRate	1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.3	Unsigned32	read-write	The bit rate per second.The operation is inactive when bit rate mode is disabled. Possible values are: 0, 100, 2100, 3100, ..., 1000000.
T/F me1200AclRateLimiterBitRateEnable	1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.4	TruthValue	read-write	Enable bit rate.
me1200AclAce	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2
me1200AclAceTable	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1		not-accessible	The ACL ACE configuration table.
me1200AclAceEntry	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1		not-accessible	Each row contains a set of parameters.
I32 me1200AclAceId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.1	Integer32	not-accessible	The identification of ACE.
U32 me1200AclAceNextAceId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.2	Unsigned32	read-write	The next identification for this ACE. Possible values are: 0(end of list), 1-512.
T/F me1200AclAceLookup	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.3	TruthValue	read-write	The second lookup operation for this ACE. Possible values are: 1(enabled) and 2(disabled).
ME1 me1200AclAceIngressPortList	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.5	ME1200PortList	read-write	The ingress port list for this ACE. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
ME1 me1200AclAcePolicyValue	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.6	ME1200Unsigned8	read-write	The policy number for this ACE. The feature is inactive when policy mask value is non-zero.
ME1 me1200AclAcePolicyMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.7	ME1200Unsigned8	read-write	The policy number for this ACE. The feature is inactive when policy mask value is non-zero.
ME1 me1200AclAceHitAction	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.8	ME1200AclAceHitAction	read-write	The hit action operation for this ACE. Note all ports will be the filter port member when filter action is set on the first time.
ME1 me1200AclAceFilterPortList	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.9	ME1200PortList	read-write	The filter port list. It is active only when the hit action is filtered. Set the action value to 0(filter) before the new setting. Note that the action will change deny action if there is no any port in the member set. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
U32 me1200AclAceRateLimiterId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.10	Unsigned32	read-write	The rate limiter ID. Possible values are: 0(disabled), 1-16.
ME1 me1200AclAceEvcPolicerId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.11	ME1200Unsigned16	read-write	The EVC policer ID. Possible values are: 0(disabled), 1-1022.
ME1 me1200AclAceRedirectPortList	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.12	ME1200PortList	read-write	The ingress port list for this ACE. It is active only when the hit action is denied. Set the action value to 1(deny) before the new setting. Set value 0 to disable the opertion. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
T/F me1200AclAceMirror	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.13	TruthValue	read-write	The rmirror operation. Frames matching this ACE are mirrored to the destination mirror port.
T/F me1200AclAceLogging	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.14	TruthValue	read-write	The logging operation.
T/F me1200AclAceShutdown	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.15	TruthValue	read-write	The shutdown operation.
ME1 me1200AclAceVlanTagged	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.100	ME1200VlanTagged	read-write	The 802.1Q VLAN tagged for this ACE.
ME1 me1200AclAceVlanId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.101	ME1200Unsigned16	read-write	The VLAN ID for this ACE. Possible values are: 0(disabled), 1-4095.
ME1 me1200AclAceVlanTagPriority	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.102	ME1200VlanTagPriority	read-write	The VLN tag priority for this ACE. Enable VLAN tagged filter before the new setting.
ME1 me1200AclAceFrameType	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.200	ME1200AclAceType	read-write	The frame type for this ACE.
ME1 me1200AclAceEtypeSrcMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.300	ME1200ASType	read-write	Indicates how a Ethernet type packet's source MAC address is to be compared. This object can only be configured if FrameType is etype(1).
MAC me1200AclAceEtypeSrcMac	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.301	MacAddress	read-write	Indicates the 48 bits source MAC address. This object can only be configured if FrameType is etype(1) and EtypeSrcMacOp is specific(1).
ME1 me1200AclAceEtypeDestMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.302	ME1200AdvDestMacType	read-write	Indicates how a Ethernet type packet's destination MAC address is to be compared. This object can only be configured if FrameType is etype(1).
MAC me1200AclAceEtypeDestMac	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.303	MacAddress	read-write	Indicates the 48 bits destination MAC address. This object can only be configured if FrameType is etype(1) and EtypeDestMacOp is specific(1).
ME1 me1200AclAceEtype	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.304	ME1200Unsigned16	read-write	Indicates the packet's 16 bit Ethernet type field. Possible values are: 0(disabled), 0x600-0xFFFF but excluding 0x800(IPv4), 0x806(ARP) and 0x86DD(IPv6).This object can only be configured if FrameType is etype(1) and EtypeDestMacOp is specific(1).
ME1 me1200AclAceArpSrcMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.600	ME1200ASType	read-write	Indicates how a ARP packet's source MAC address is to be compared. This object can only be configured if FrameType is arp(4).
MAC me1200AclAceArpSrcMac	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.601	MacAddress	read-write	Indicates the 48 bits source MAC address. This object can only be configured if FrameType is arp(4) and ArpSrcMacOp is specific(1).
ME1 me1200AclAceArpDestMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.602	ME1200DestMacType	read-write	Indicates how a ARP packet's destination MAC address is to be compared. This object can only be configured if FrameType is arp(4).
IP me1200AclAceArpSenderIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.603	IpAddress	read-write	The specified ARP sender IP address. The packets sender address is AND-ed with the value of ArpSenderIpMask and then compared with the value of this object. If ArpSenderIp and ArpSrcIpMask are 0.0.0.0, this entry matches any sender IP address. This object can only be configured if FrameType is arp(4).
IP me1200AclAceArpSenderIpMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.604	IpAddress	read-write	The specified ARP sender IP address mask. This object can only be configured if FrameType is arp(4).
IP me1200AclAceArpTragetIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.605	IpAddress	read-write	The specified ARP target IP address. The packets target address is AND-ed with the value of ArpTragetIpMask and then compared with the value of this object. If ArpTragetIp and ArpSrcIpMask are 0.0.0.0, this entry matches any target IP address. This object can only be configured if FrameType is arp(4).
IP me1200AclAceArpTragetIpMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.606	IpAddress	read-write	The specified ARP target IP address mask. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceArpOpcode	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.607	ME1200ArpOpcode	read-write	Indicates how a ARP packet's opcode is to be compared. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceArpFlagRequest	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.608	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's request/reply opcode is to be compared. The value 0 means any ARP opcode is allowed (don't-care field), value 1 means ARP opcode is equal to request opcode and value 2 means ARP opcode is equal to reply opcode. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceArpFlagSenderMac	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.609	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's sender hardware address field (SHA) is to be compared. The value 0 means any SHA value is allowed (don't-care field), value 1 means SHA is not equal to the SMAC address and value 2 means SHA is equal to the SMAC address. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceArpFlagTargetMac	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.610	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's target hardware address field (THA) is to be compared. The value 0 means any THA value is allowed (don't-care field), value 1 means THA is not equal to the DMAC address and value 2 means THA is equal to the DMAC address. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceArpFlagLen	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.611	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's s hardware address length field (HLN) is to be compared. The value 0 means any HLN value is allowed (don't-care field), value 1 means HLN is not equal to Ethernet (0x06) or the (PLN) is not equal to IPv4 (0x04) and value 2 means HLN is equal to Ethernet (0x06) or the (PLN) is not equal to IPv4 (0x04). This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceArpFlagIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.612	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's hardware address space field (HRD) is to be compared. The value 0 means any HRD value is allowed (don't-care field), value 1 means HRD is not equal to Ethernet (1) and value 2 means HRD is equal to Ethernet (1). This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceArpFlagEthernet	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.613	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's protocol address space field (PRO) is to be compared. The value 0 means any PRO value is allowed (don't-care field), value 1 means PRO is not equal to IP (0x800) and value 2 means PRO is equal to IP (0x800). This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceIpv4DestMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.700	ME1200DestMacType	read-write	Indicates how a IPv4 packet's destination MAC address is to be compared. This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceIpv4ProtocolOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.701	ME1200ASType	read-write	Indicates how a IPv4 packet's protocol field is to be compared. This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceIpv4Protocol	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.702	ME1200Unsigned8	read-write	The protocol number field in the IPv4 header used to indicate a higher layer protocol. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolOp is specific(1).
ME1 me1200AclAceIpv4FlagTtl	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.703	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 packet's Time-to-Live field (TTL) is to be compared. The value 0 means any TTL value is allowed (don't-care field), value 1 means TTL is not equal zero and value 2 means TTL is equal to zero. This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceIpv4FlagFragment	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.704	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 packet's More-Fragments field (MF) is to be compared. The value 0 means any MF value is allowed (don't-care field), value 1 means MF is not equal one (MF field isn't set) and value 2 means MF is equal to one (MF field is set). This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceIpv4FlagIpOption	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.705	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 packet's options field is to be compared. The value 0 means any options is allowed (don't-care field), value 1 means options is not equal one (options field isn't set) and value 2 means options is equal to one (options field is set). This object can only be configured if FrameType is ipv4(5).
IP me1200AclAceIpv4SrcIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.706	IpAddress	read-write	The specified source IPv4 address. The packets sender address is AND-ed with the value of Ipv4SrcIpMask and then compared with the value of this object. If Ipv4SrcIp and Ipv4SrcIpMask are 0.0.0.0, this entry matches any source IP address. This object can only be configured if FrameType is ipv4(5).
IP me1200AclAceIpv4SrcIpMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.707	IpAddress	read-write	The specified source IPv4 address mask. This object can only be configured if FrameType isipv4(5).
IP me1200AclAceIpv4DestIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.708	IpAddress	read-write	The specified destination IPv4 address. The packets sender address is AND-ed with the value of Ipv4DestIpMask and then compared with the value of this object. If Ipv4DestIp and Ipv4DestIpMask are 0.0.0.0, this entry matches any destination IP address. This object can only be configured if FrameType is ipv4(5).
IP me1200AclAceIpv4DestIpMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.709	IpAddress	read-write	The specified destination IPv4 address mask. This object can only be configured if FrameType isipv4(5).
ME1 me1200AclAceIpv4IcmpTypeOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.710	ME1200ASType	read-write	Indicates how a IPv4 packet's ICMP type field is to be compared. This object can only be configured if FrameType is ipv4(5) and Ipv4Protocol is icmp(1).
ME1 me1200AclAceIpv4IcmpType	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.711	ME1200Unsigned8	read-write	The ICMP type field in the IPv4 header. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5), Ipv4Protocol is icmp(1) and Ipv4IcmpTypeOp is specific(1).
ME1 me1200AclAceIpv4IcmpCodeOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.712	ME1200ASType	read-write	Indicates how a IPv4 packet's ICMP code field is to be compared. This object can only be configured if FrameType is ipv4(5) and Ipv4Protocol is icmp(1).
ME1 me1200AclAceIpv4IcmpCode	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.713	ME1200Unsigned8	read-write	The ICMP code field in the IPv4 header. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5), Ipv4Protocol is icmp(1) and Ipv4IcmpCodeOp is specific(1).
ME1 me1200AclAceIpv4SrcPortOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.714	ME1200ASRType	read-write	Indicates how a packet's source TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceIpv4SrcPort	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.715	ME1200Unsigned16	read-write	The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is not any(0).
ME1 me1200AclAceIpv4SrcPortRange	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.716	ME1200Unsigned16	read-write	The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is range(2).
ME1 me1200AclAceIpv4DestPortOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.717	ME1200ASRType	read-write	Indicates how a packet's destination TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceIpv4DestPort	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.718	ME1200Unsigned16	read-write	The destination port number of the TCP or UDP protocol. If the Ipv4DestPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4DestPortOp is not any(0).
ME1 me1200AclAceIpv4DestPortRange	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.719	ME1200Unsigned16	read-write	The destination port number of the TCP or UDP protocol. If the Ipv4DestPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4DestPortOp is range(2).
ME1 me1200AclAceIpv4TcpFlagFin	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.720	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'No more data from sender' field (FIN) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means FIN is not equal one (FIN field isn't set) and value 2 means FIN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceIpv4TcpFlagSyn	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.721	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'Synchronize sequence numbers' field (SYN) is to be compared. The value 0 means any SYN value is allowed (don't-care field), value 1 means SYN is not equal one (FIN field isn't set) and value 2 means SYN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceIpv4TcpFlagRst	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.722	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'Reset the connection' field (RST) is to be compared. The value 0 means any RST value is allowed (don't-care field), value 1 means RST is not equal one (FIN field isn't set) and value 2 means RST is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceIpv4TcpFlagPsh	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.723	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'Push Function' field (PSH) is to be compared. The value 0 means any PSH value is allowed (don't-care field), value 1 means PSH is not equal one (FIN field isn't set) and value 2 means PSH is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceIpv4TcpFlagAck	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.724	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'Acknowledgment field significant' field (ACK) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means ACK is not equal one (FIN field isn't set) and value 2 means ACK is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceIpv4TcpFlagUrg	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.725	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'Urgent Pointer field significant' field (URG) is to be compared. The value 0 means any URG value is allowed (don't-care field), value 1 means URG is not equal one (FIN field isn't set) and value 2 means URG is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceIPv6DestMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.800	ME1200DestMacType	read-write	Indicates how a IPv6 packet's destination MAC address is to be compared. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceIpv6NextHeaderOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.801	ME1200ASType	read-write	Indicates how a IPv6 packet's next header field is to be compared. This object can only be configured if FrameType is ipv6(6).
ME1 me1200AclAceIpv6NextHeader	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.802	ME1200Unsigned8	read-write	The next header field in the IPv6 header used to indicate a higher layer protocol. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeaderOp is specific(1).
ADR me1200AclAceIpv6SrcIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.803	InetAddressIPv6	read-write	The specified IPv6 source address. The packets source address is AND-ed with the value of Ipv6SrcIpMask and then compared with the value of this object. If Ipv6SrcIp and Ipv6SrcIpMask are all zeros, this entry matches any IPv6 source address. Only the least significant 32 bits of this object are used. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcIpMask is not all zeros.
ADR me1200AclAceIpv6SrcIpMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.804	InetAddressIPv6	read-write	The specified IPv6 source address mask. Only the least significant 32 bits of this object are used. This object can only be configured if FrameType is ipv6(6).
ME1 me1200AclAceIpv6FlagHopLimiter	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.805	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 packet's hop limit field is to be compared. The value 0 means any hop limit value is allowed (don't-care field), value 1 means hop limit is not equal zero and value 2 means hop limit is equal to zero. This object can only be configured if FrameType is ipv6(6).
ME1 me1200AclAceIpv6Icmpv6TypeOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.806	ME1200ASType	read-write	Indicates how a IPv6 packet's ICMPv6 type field is to be compared. This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeader is icmpv6(58).
ME1 me1200AclAceIpv6Icmpv6Type	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.807	ME1200Unsigned8	read-write	The ICMPv6 type field in the IPv6 header. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6), Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6TypeOp is specific(1).
ME1 me1200AclAceIpv6Icmpv6CodeOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.808	ME1200ASType	read-write	Indicates how a IPv6 packet's ICMPv6 code field is to be compared. This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeader is icmpv6(58).
ME1 me1200AclAceIpv6Icmpv6Code	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.809	ME1200Unsigned8	read-write	The ICMPv6 code field in the IPv6 header. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6), Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6CodeOp is specific(1).
ME1 me1200AclAceIpv6SrcPortOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.810	ME1200ASRType	read-write	Indicates how a packet's source TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv6(6).
ME1 me1200AclAceIpv6SrcPort	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.811	ME1200Unsigned16	read-write	The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is not any(0).
ME1 me1200AclAceIpv6SrcPortRange	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.812	ME1200Unsigned16	read-write	The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is range(2).
ME1 me1200AclAceIpv6DestPortOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.813	ME1200ASRType	read-write	Indicates how a packet's destination TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv6(6).
ME1 me1200AclAceIpv6DestPort	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.814	ME1200Unsigned16	read-write	The destination port number of the TCP or UDP protocol. If the Ipv6DestPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6DestPortOp is not any(0).
ME1 me1200AclAceIpv6DestPortRange	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.815	ME1200Unsigned16	read-write	The destination port number of the TCP or UDP protocol. If the Ipv6DestPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6DestPortOp is range(2).
ME1 me1200AclAceIpv6TcpFlagFin	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.816	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'No more data from sender' field (FIN) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means FIN is not equal one (FIN field isn't set) and value 2 means FIN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceIpv6TcpFlagSyn	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.817	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'Synchronize sequence numbers' field (SYN) is to be compared. The value 0 means any SYN value is allowed (don't-care field), value 1 means SYN is not equal one (FIN field isn't set) and value 2 means SYN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceIpv6TcpFlagRst	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.818	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'Reset the connection' field (RST) is to be compared. The value 0 means any RST value is allowed (don't-care field), value 1 means RST is not equal one (FIN field isn't set) and value 2 means RST is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceIpv6TcpFlagPsh	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.819	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'Push Function' field (PSH) is to be compared. The value 0 means any PSH value is allowed (don't-care field), value 1 means PSH is not equal one (FIN field isn't set) and value 2 means PSH is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceIpv6TcpFlagAck	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.820	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'Acknowledgment field significant' field (ACK) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means ACK is not equal one (FIN field isn't set) and value 2 means ACK is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceIpv6TcpFlagUrg	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.821	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'Urgent Pointer field significant' field (URG) is to be compared. The value 0 means any URG value is allowed (don't-care field), value 1 means URG is not equal one (FIN field isn't set) and value 2 means URG is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceAction	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.1000	ME1200RowEditorState	read-write	Action
me1200AclAceTableRowEditor	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2
I32 me1200AclAceTableRowEditorId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.1	Integer32	read-write	The identification of ACE.
U32 me1200AclAceTableRowEditorNextAceId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.2	Unsigned32	read-write	The next identification for this ACE. Possible values are: 0(end of list), 1-512.
T/F me1200AclAceTableRowEditorLookup	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.3	TruthValue	read-write	The second lookup operation for this ACE. Possible values are: 1(enabled) and 2(disabled).
ME1 me1200AclAceTableRowEditorIngressPortList	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.5	ME1200PortList	read-write	The ingress port list for this ACE. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
ME1 me1200AclAceTableRowEditorPolicyValue	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.6	ME1200Unsigned8	read-write	The policy number for this ACE. The feature is inactive when policy mask value is non-zero.
ME1 me1200AclAceTableRowEditorPolicyMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.7	ME1200Unsigned8	read-write	The policy number for this ACE. The feature is inactive when policy mask value is non-zero.
ME1 me1200AclAceTableRowEditorHitAction	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.8	ME1200AclAceHitAction	read-write	The hit action operation for this ACE. Note all ports will be the filter port member when filter action is set on the first time.
ME1 me1200AclAceTableRowEditorFilterPortList	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.9	ME1200PortList	read-write	The filter port list. It is active only when the hit action is filtered. Set the action value to 0(filter) before the new setting. Note that the action will change deny action if there is no any port in the member set. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
U32 me1200AclAceTableRowEditorRateLimiterId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.10	Unsigned32	read-write	The rate limiter ID. Possible values are: 0(disabled), 1-16.
ME1 me1200AclAceTableRowEditorEvcPolicerId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.11	ME1200Unsigned16	read-write	The EVC policer ID. Possible values are: 0(disabled), 1-1022.
ME1 me1200AclAceTableRowEditorRedirectPortList	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.12	ME1200PortList	read-write	The ingress port list for this ACE. It is active only when the hit action is denied. Set the action value to 1(deny) before the new setting. Set value 0 to disable the opertion. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
T/F me1200AclAceTableRowEditorMirror	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.13	TruthValue	read-write	The rmirror operation. Frames matching this ACE are mirrored to the destination mirror port.
T/F me1200AclAceTableRowEditorLogging	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.14	TruthValue	read-write	The logging operation.
T/F me1200AclAceTableRowEditorShutdown	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.15	TruthValue	read-write	The shutdown operation.
ME1 me1200AclAceTableRowEditorVlanTagged	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.100	ME1200VlanTagged	read-write	The 802.1Q VLAN tagged for this ACE.
ME1 me1200AclAceTableRowEditorVlanId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.101	ME1200Unsigned16	read-write	The VLAN ID for this ACE. Possible values are: 0(disabled), 1-4095.
ME1 me1200AclAceTableRowEditorVlanTagPriority	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.102	ME1200VlanTagPriority	read-write	The VLN tag priority for this ACE. Enable VLAN tagged filter before the new setting.
ME1 me1200AclAceTableRowEditorFrameType	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.200	ME1200AclAceType	read-write	The frame type for this ACE.
ME1 me1200AclAceTableRowEditorEtypeSrcMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.300	ME1200ASType	read-write	Indicates how a Ethernet type packet's source MAC address is to be compared. This object can only be configured if FrameType is etype(1).
MAC me1200AclAceTableRowEditorEtypeSrcMac	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.301	MacAddress	read-write	Indicates the 48 bits source MAC address. This object can only be configured if FrameType is etype(1) and EtypeSrcMacOp is specific(1).
ME1 me1200AclAceTableRowEditorEtypeDestMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.302	ME1200AdvDestMacType	read-write	Indicates how a Ethernet type packet's destination MAC address is to be compared. This object can only be configured if FrameType is etype(1).
MAC me1200AclAceTableRowEditorEtypeDestMac	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.303	MacAddress	read-write	Indicates the 48 bits destination MAC address. This object can only be configured if FrameType is etype(1) and EtypeDestMacOp is specific(1).
ME1 me1200AclAceTableRowEditorEtype	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.304	ME1200Unsigned16	read-write	Indicates the packet's 16 bit Ethernet type field. Possible values are: 0(disabled), 0x600-0xFFFF but excluding 0x800(IPv4), 0x806(ARP) and 0x86DD(IPv6).This object can only be configured if FrameType is etype(1) and EtypeDestMacOp is specific(1).
ME1 me1200AclAceTableRowEditorArpSrcMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.600	ME1200ASType	read-write	Indicates how a ARP packet's source MAC address is to be compared. This object can only be configured if FrameType is arp(4).
MAC me1200AclAceTableRowEditorArpSrcMac	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.601	MacAddress	read-write	Indicates the 48 bits source MAC address. This object can only be configured if FrameType is arp(4) and ArpSrcMacOp is specific(1).
ME1 me1200AclAceTableRowEditorArpDestMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.602	ME1200DestMacType	read-write	Indicates how a ARP packet's destination MAC address is to be compared. This object can only be configured if FrameType is arp(4).
IP me1200AclAceTableRowEditorArpSenderIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.603	IpAddress	read-write	The specified ARP sender IP address. The packets sender address is AND-ed with the value of ArpSenderIpMask and then compared with the value of this object. If ArpSenderIp and ArpSrcIpMask are 0.0.0.0, this entry matches any sender IP address. This object can only be configured if FrameType is arp(4).
IP me1200AclAceTableRowEditorArpSenderIpMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.604	IpAddress	read-write	The specified ARP sender IP address mask. This object can only be configured if FrameType is arp(4).
IP me1200AclAceTableRowEditorArpTragetIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.605	IpAddress	read-write	The specified ARP target IP address. The packets target address is AND-ed with the value of ArpTragetIpMask and then compared with the value of this object. If ArpTragetIp and ArpSrcIpMask are 0.0.0.0, this entry matches any target IP address. This object can only be configured if FrameType is arp(4).
IP me1200AclAceTableRowEditorArpTragetIpMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.606	IpAddress	read-write	The specified ARP target IP address mask. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceTableRowEditorArpOpcode	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.607	ME1200ArpOpcode	read-write	Indicates how a ARP packet's opcode is to be compared. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceTableRowEditorArpFlagRequest	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.608	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's request/reply opcode is to be compared. The value 0 means any ARP opcode is allowed (don't-care field), value 1 means ARP opcode is equal to request opcode and value 2 means ARP opcode is equal to reply opcode. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceTableRowEditorArpFlagSenderMac	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.609	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's sender hardware address field (SHA) is to be compared. The value 0 means any SHA value is allowed (don't-care field), value 1 means SHA is not equal to the SMAC address and value 2 means SHA is equal to the SMAC address. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceTableRowEditorArpFlagTargetMac	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.610	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's target hardware address field (THA) is to be compared. The value 0 means any THA value is allowed (don't-care field), value 1 means THA is not equal to the DMAC address and value 2 means THA is equal to the DMAC address. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceTableRowEditorArpFlagLen	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.611	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's s hardware address length field (HLN) is to be compared. The value 0 means any HLN value is allowed (don't-care field), value 1 means HLN is not equal to Ethernet (0x06) or the (PLN) is not equal to IPv4 (0x04) and value 2 means HLN is equal to Ethernet (0x06) or the (PLN) is not equal to IPv4 (0x04). This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceTableRowEditorArpFlagIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.612	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's hardware address space field (HRD) is to be compared. The value 0 means any HRD value is allowed (don't-care field), value 1 means HRD is not equal to Ethernet (1) and value 2 means HRD is equal to Ethernet (1). This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceTableRowEditorArpFlagEthernet	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.613	ME1200AclAceFlagOpcode	read-write	Indicates how a ARP packet's protocol address space field (PRO) is to be compared. The value 0 means any PRO value is allowed (don't-care field), value 1 means PRO is not equal to IP (0x800) and value 2 means PRO is equal to IP (0x800). This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceTableRowEditorIpv4DestMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.700	ME1200DestMacType	read-write	Indicates how a IPv4 packet's destination MAC address is to be compared. This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceTableRowEditorIpv4ProtocolOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.701	ME1200ASType	read-write	Indicates how a IPv4 packet's protocol field is to be compared. This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceTableRowEditorIpv4Protocol	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.702	ME1200Unsigned8	read-write	The protocol number field in the IPv4 header used to indicate a higher layer protocol. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolOp is specific(1).
ME1 me1200AclAceTableRowEditorIpv4FlagTtl	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.703	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 packet's Time-to-Live field (TTL) is to be compared. The value 0 means any TTL value is allowed (don't-care field), value 1 means TTL is not equal zero and value 2 means TTL is equal to zero. This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceTableRowEditorIpv4FlagFragment	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.704	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 packet's More-Fragments field (MF) is to be compared. The value 0 means any MF value is allowed (don't-care field), value 1 means MF is not equal one (MF field isn't set) and value 2 means MF is equal to one (MF field is set). This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceTableRowEditorIpv4FlagIpOption	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.705	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 packet's options field is to be compared. The value 0 means any options is allowed (don't-care field), value 1 means options is not equal one (options field isn't set) and value 2 means options is equal to one (options field is set). This object can only be configured if FrameType is ipv4(5).
IP me1200AclAceTableRowEditorIpv4SrcIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.706	IpAddress	read-write	The specified source IPv4 address. The packets sender address is AND-ed with the value of Ipv4SrcIpMask and then compared with the value of this object. If Ipv4SrcIp and Ipv4SrcIpMask are 0.0.0.0, this entry matches any source IP address. This object can only be configured if FrameType is ipv4(5).
IP me1200AclAceTableRowEditorIpv4SrcIpMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.707	IpAddress	read-write	The specified source IPv4 address mask. This object can only be configured if FrameType isipv4(5).
IP me1200AclAceTableRowEditorIpv4DestIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.708	IpAddress	read-write	The specified destination IPv4 address. The packets sender address is AND-ed with the value of Ipv4DestIpMask and then compared with the value of this object. If Ipv4DestIp and Ipv4DestIpMask are 0.0.0.0, this entry matches any destination IP address. This object can only be configured if FrameType is ipv4(5).
IP me1200AclAceTableRowEditorIpv4DestIpMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.709	IpAddress	read-write	The specified destination IPv4 address mask. This object can only be configured if FrameType isipv4(5).
ME1 me1200AclAceTableRowEditorIpv4IcmpTypeOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.710	ME1200ASType	read-write	Indicates how a IPv4 packet's ICMP type field is to be compared. This object can only be configured if FrameType is ipv4(5) and Ipv4Protocol is icmp(1).
ME1 me1200AclAceTableRowEditorIpv4IcmpType	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.711	ME1200Unsigned8	read-write	The ICMP type field in the IPv4 header. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5), Ipv4Protocol is icmp(1) and Ipv4IcmpTypeOp is specific(1).
ME1 me1200AclAceTableRowEditorIpv4IcmpCodeOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.712	ME1200ASType	read-write	Indicates how a IPv4 packet's ICMP code field is to be compared. This object can only be configured if FrameType is ipv4(5) and Ipv4Protocol is icmp(1).
ME1 me1200AclAceTableRowEditorIpv4IcmpCode	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.713	ME1200Unsigned8	read-write	The ICMP code field in the IPv4 header. Possible values are 0-255.This object can only be configured if FrameType is ipv4(5), Ipv4Protocol is icmp(1) and Ipv4IcmpCodeOp is specific(1).
ME1 me1200AclAceTableRowEditorIpv4SrcPortOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.714	ME1200ASRType	read-write	Indicates how a packet's source TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceTableRowEditorIpv4SrcPort	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.715	ME1200Unsigned16	read-write	The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is not any(0).
ME1 me1200AclAceTableRowEditorIpv4SrcPortRange	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.716	ME1200Unsigned16	read-write	The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is range(2).
ME1 me1200AclAceTableRowEditorIpv4DestPortOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.717	ME1200ASRType	read-write	Indicates how a packet's destination TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv4(5).
ME1 me1200AclAceTableRowEditorIpv4DestPort	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.718	ME1200Unsigned16	read-write	The destination port number of the TCP or UDP protocol. If the Ipv4DestPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4DestPortOp is not any(0).
ME1 me1200AclAceTableRowEditorIpv4DestPortRange	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.719	ME1200Unsigned16	read-write	The destination port number of the TCP or UDP protocol. If the Ipv4DestPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv4(5) and Ipv4DestPortOp is range(2).
ME1 me1200AclAceTableRowEditorIpv4TcpFlagFin	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.720	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'No more data from sender' field (FIN) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means FIN is not equal one (FIN field isn't set) and value 2 means FIN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorIpv4TcpFlagSyn	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.721	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'Synchronize sequence numbers' field (SYN) is to be compared. The value 0 means any SYN value is allowed (don't-care field), value 1 means SYN is not equal one (FIN field isn't set) and value 2 means SYN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorIpv4TcpFlagRst	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.722	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'Reset the connection' field (RST) is to be compared. The value 0 means any RST value is allowed (don't-care field), value 1 means RST is not equal one (FIN field isn't set) and value 2 means RST is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorIpv4TcpFlagPsh	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.723	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'Push Function' field (PSH) is to be compared. The value 0 means any PSH value is allowed (don't-care field), value 1 means PSH is not equal one (FIN field isn't set) and value 2 means PSH is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorIpv4TcpFlagAck	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.724	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'Acknowledgment field significant' field (ACK) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means ACK is not equal one (FIN field isn't set) and value 2 means ACK is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorIpv4TcpFlagUrg	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.725	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv4 TCP packet's 'Urgent Pointer field significant' field (URG) is to be compared. The value 0 means any URG value is allowed (don't-care field), value 1 means URG is not equal one (FIN field isn't set) and value 2 means URG is equal to one (FIN field is set). This object can only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorIPv6DestMacOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.800	ME1200DestMacType	read-write	Indicates how a IPv6 packet's destination MAC address is to be compared. This object can only be configured if FrameType is arp(4).
ME1 me1200AclAceTableRowEditorIpv6NextHeaderOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.801	ME1200ASType	read-write	Indicates how a IPv6 packet's next header field is to be compared. This object can only be configured if FrameType is ipv6(6).
ME1 me1200AclAceTableRowEditorIpv6NextHeader	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.802	ME1200Unsigned8	read-write	The next header field in the IPv6 header used to indicate a higher layer protocol. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeaderOp is specific(1).
ADR me1200AclAceTableRowEditorIpv6SrcIp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.803	InetAddressIPv6	read-write	The specified IPv6 source address. The packets source address is AND-ed with the value of Ipv6SrcIpMask and then compared with the value of this object. If Ipv6SrcIp and Ipv6SrcIpMask are all zeros, this entry matches any IPv6 source address. Only the least significant 32 bits of this object are used. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcIpMask is not all zeros.
ADR me1200AclAceTableRowEditorIpv6SrcIpMask	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.804	InetAddressIPv6	read-write	The specified IPv6 source address mask. Only the least significant 32 bits of this object are used. This object can only be configured if FrameType is ipv6(6).
ME1 me1200AclAceTableRowEditorIpv6FlagHopLimiter	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.805	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 packet's hop limit field is to be compared. The value 0 means any hop limit value is allowed (don't-care field), value 1 means hop limit is not equal zero and value 2 means hop limit is equal to zero. This object can only be configured if FrameType is ipv6(6).
ME1 me1200AclAceTableRowEditorIpv6Icmpv6TypeOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.806	ME1200ASType	read-write	Indicates how a IPv6 packet's ICMPv6 type field is to be compared. This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeader is icmpv6(58).
ME1 me1200AclAceTableRowEditorIpv6Icmpv6Type	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.807	ME1200Unsigned8	read-write	The ICMPv6 type field in the IPv6 header. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6), Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6TypeOp is specific(1).
ME1 me1200AclAceTableRowEditorIpv6Icmpv6CodeOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.808	ME1200ASType	read-write	Indicates how a IPv6 packet's ICMPv6 code field is to be compared. This object can only be configured if FrameType is ipv6(6) and Ipv6NextHeader is icmpv6(58).
ME1 me1200AclAceTableRowEditorIpv6Icmpv6Code	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.809	ME1200Unsigned8	read-write	The ICMPv6 code field in the IPv6 header. Possible values are 0-255.This object can only be configured if FrameType is ipv6(6), Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6CodeOp is specific(1).
ME1 me1200AclAceTableRowEditorIpv6SrcPortOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.810	ME1200ASRType	read-write	Indicates how a packet's source TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv6(6).
ME1 me1200AclAceTableRowEditorIpv6SrcPort	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.811	ME1200Unsigned16	read-write	The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is not any(0).
ME1 me1200AclAceTableRowEditorIpv6SrcPortRange	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.812	ME1200Unsigned16	read-write	The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is range(2).
ME1 me1200AclAceTableRowEditorIpv6DestPortOp	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.813	ME1200ASRType	read-write	Indicates how a packet's destination TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv6(6).
ME1 me1200AclAceTableRowEditorIpv6DestPort	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.814	ME1200Unsigned16	read-write	The destination port number of the TCP or UDP protocol. If the Ipv6DestPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6DestPortOp is not any(0).
ME1 me1200AclAceTableRowEditorIpv6DestPortRange	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.815	ME1200Unsigned16	read-write	The destination port number of the TCP or UDP protocol. If the Ipv6DestPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be configured if FrameType is ipv6(6) and Ipv6DestPortOp is range(2).
ME1 me1200AclAceTableRowEditorIpv6TcpFlagFin	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.816	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'No more data from sender' field (FIN) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means FIN is not equal one (FIN field isn't set) and value 2 means FIN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorIpv6TcpFlagSyn	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.817	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'Synchronize sequence numbers' field (SYN) is to be compared. The value 0 means any SYN value is allowed (don't-care field), value 1 means SYN is not equal one (FIN field isn't set) and value 2 means SYN is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorIpv6TcpFlagRst	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.818	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'Reset the connection' field (RST) is to be compared. The value 0 means any RST value is allowed (don't-care field), value 1 means RST is not equal one (FIN field isn't set) and value 2 means RST is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorIpv6TcpFlagPsh	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.819	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'Push Function' field (PSH) is to be compared. The value 0 means any PSH value is allowed (don't-care field), value 1 means PSH is not equal one (FIN field isn't set) and value 2 means PSH is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorIpv6TcpFlagAck	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.820	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'Acknowledgment field significant' field (ACK) is to be compared. The value 0 means any FIN value is allowed (don't-care field), value 1 means ACK is not equal one (FIN field isn't set) and value 2 means ACK is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorIpv6TcpFlagUrg	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.821	ME1200AclAceFlagOpcode	read-write	Indicates how a IPv6 TCP packet's 'Urgent Pointer field significant' field (URG) is to be compared. The value 0 means any URG value is allowed (don't-care field), value 1 means URG is not equal one (FIN field isn't set) and value 2 means URG is equal to one (FIN field is set). This object can only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is tcp(6).
ME1 me1200AclAceTableRowEditorAction	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.1000	ME1200RowEditorState	read-write	Action
me1200AclAcePrecedenceTable	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3		not-accessible	This table provides an overview of ACE by hit precedence.
me1200AclAcePrecedenceEntry	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3.1		not-accessible	Each row contains a set of parameters.
I32 me1200AclAcePrecedencePrecedenceIndex	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3.1.1	Integer32	not-accessible	The ACL ACE hit precedence.
U32 me1200AclAcePrecedenceAceId	1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3.1.2	Unsigned32	read-only	The identification for this ACE. Possible values are: 0(end of list), 1-512.
me1200AclInterface	1.3.6.1.4.1.9.9.815.1.17.1.2.2
me1200AclInterfaceTable	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1		not-accessible	The ACL interface configuration table.
me1200AclInterfaceEntry	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1		not-accessible	Each interface has a set of parameters
NUM me1200AclInterfaceIfIndex	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.1	ME1200InterfaceIndex	not-accessible	The index of logical interface, it is as well as the IF-MIB [RFC2863] objects ifIndex.
U32 me1200AclInterfacePolicyId	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.2	Unsigned32	read-write	The policy ID. Possible values are: 0-63.
NUM me1200AclInterfaceHitAction	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.3	ME1200AclInterfaceHitAction	read-write	The hit action.
U32 me1200AclInterfaceRateLimiterId	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.4	Unsigned32	read-write	The rate limiter ID. Possible values are: 0(disabled), 1-16.
ME1 me1200AclInterfaceEvcPolicerId	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.5	ME1200Unsigned16	read-write	The EVC policer ID. Possible values are: 0(disabled), 1-1022.
ME1 me1200AclInterfaceRedirectPortList	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.6	ME1200PortList	read-write	The ingress port list for this ACE. It is active only when the hit action is denied. Set the action value to 1(deny) before the new setting. Set value 0 to disable the opertion. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
T/F me1200AclInterfaceMirror	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.7	TruthValue	read-write	The rmirror operation. Frames matching this ACE are mirrored to the destination mirror port.
T/F me1200AclInterfaceLogging	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.8	TruthValue	read-write	The logging operation.
T/F me1200AclInterfaceShutdown	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.9	TruthValue	read-write	The shutdown operation.
T/F me1200AclInterfaceState	1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.10	TruthValue	read-write	The port state of this interface.
me1200AclStatus	1.3.6.1.4.1.9.9.815.1.17.1.3
me1200AclStatusGlobals	1.3.6.1.4.1.9.9.815.1.17.1.3.1
me1200AclAceStatusTable	1.3.6.1.4.1.9.9.815.1.17.1.3.1.1		not-accessible	This table provides the ACE status in the hardware table.
me1200AclAceStatusEntry	1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1		not-accessible	Each row contains a set of parameters.
I32 me1200AclAceStatusPrecedenceIndex	1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.2	Integer32	not-accessible	The ACL ACE hit precedence.
ME1 me1200AclAceStatusUser	1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.3	ME1200AclUser	read-only	The application user of ACL.
U32 me1200AclAceStatusAceId	1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.4	Unsigned32	read-only	The identification for this ACE. Possible values are: 0(end of list), 1-512.
T/F me1200AclAceStatusConflict	1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.5	TruthValue	read-only	The conflict status of this ACE. When the status value is 1(true), it means the specific ACE is not applied to the hardware due to hardware limitations.
me1200AclAceHitCountTable	1.3.6.1.4.1.9.9.815.1.17.1.3.1.2		not-accessible	The ACL ACE hit count table.
me1200AclAceHitCountEntry	1.3.6.1.4.1.9.9.815.1.17.1.3.1.2.1		not-accessible	Each row has the hit count of ACE
I32 me1200AclAceHitCountAceId	1.3.6.1.4.1.9.9.815.1.17.1.3.1.2.1.1	Integer32	not-accessible	The identification of ACE.
U32 me1200AclAceHitCountHitCount	1.3.6.1.4.1.9.9.815.1.17.1.3.1.2.1.2	Unsigned32	read-only	The hit count of this ACE.
me1200AclStatusInterface	1.3.6.1.4.1.9.9.815.1.17.1.3.2
me1200AclInterfaceHitCountTable	1.3.6.1.4.1.9.9.815.1.17.1.3.2.1		not-accessible	The ACL interface hit count table.
me1200AclInterfaceHitCountEntry	1.3.6.1.4.1.9.9.815.1.17.1.3.2.1.1		not-accessible	Each row has the hit count of interface
I32 me1200AclInterfaceHitCountId	1.3.6.1.4.1.9.9.815.1.17.1.3.2.1.1.1	Integer32	not-accessible	The identification of ACE.
U32 me1200AclInterfaceHitCountHitCount	1.3.6.1.4.1.9.9.815.1.17.1.3.2.1.1.2	Unsigned32	read-only	The hit count of this interface. The hit count will be increased if the incoming frame doesn't hit any ACEs.
me1200AclControl	1.3.6.1.4.1.9.9.815.1.17.1.4
me1200AclControlGlobals	1.3.6.1.4.1.9.9.815.1.17.1.4.1
T/F me1200AclControlGlobalsClearAllHitCount	1.3.6.1.4.1.9.9.815.1.17.1.4.1.1	TruthValue	read-write	The operation is active when the value is set to 'ture(1)'.
me1200AclMIBConformance	1.3.6.1.4.1.9.9.815.1.17.3
me1200AclMIBCompliances	1.3.6.1.4.1.9.9.815.1.17.3.1
me1200AclMIBCompliance	1.3.6.1.4.1.9.9.815.1.17.3.1.1			The compliance statement for the implementation.
me1200AclMIBGroups	1.3.6.1.4.1.9.9.815.1.17.3.2
me1200AclRateLimiterTableInfoGroup	1.3.6.1.4.1.9.9.815.1.17.3.2.1			A collection of objects suitable for bulk operations.
me1200AclAceTableInfoGroup	1.3.6.1.4.1.9.9.815.1.17.3.2.2			A collection of objects suitable for bulk operations.
me1200AclAceTableRowEditorInfoGroup	1.3.6.1.4.1.9.9.815.1.17.3.2.3			A collection of objects suitable for bulk operations.
me1200AclAcePrecedenceTableInfoGroup	1.3.6.1.4.1.9.9.815.1.17.3.2.4			A collection of objects suitable for bulk operations.
me1200AclInterfaceTableInfoGroup	1.3.6.1.4.1.9.9.815.1.17.3.2.5			A collection of objects suitable for bulk operations.
me1200AclAceStatusTableInfoGroup	1.3.6.1.4.1.9.9.815.1.17.3.2.6			A collection of objects suitable for bulk operations.
me1200AclAceHitCountTableInfoGroup	1.3.6.1.4.1.9.9.815.1.17.3.2.7			A collection of objects suitable for bulk operations.
me1200AclInterfaceHitCountTableInfoGroup	1.3.6.1.4.1.9.9.815.1.17.3.2.8			A collection of objects suitable for bulk operations.
me1200AclControlGlobalsInfoGroup	1.3.6.1.4.1.9.9.815.1.17.3.2.9			A collection of objects suitable for bulk operations.

RFC description

Manages Access Control Lists and security policies for Cisco ME1200 switches.

Start monitoring Cisco ME1200 Metro Ethernet access switch (ACL/rate limiter) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ME1200-ACL-MIB

What Is ME1200-ACL-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description