LLDP-V2-MIB

All MIBs › LLDP-V2-MIB

Organization: IEEE 802.1 Working Group

Last Updated: 2016-03-11

Category: Protocol: LLDP, Standard: IEEE 802

Description: IEEE 802.1AB version 2 standard MIB providing updated LLDP objects for enhanced neighbor discovery, topology, and TLV management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is LLDP-V2-MIB?

LLDP-V2-MIB is the vendor-neutral IEEE 802.1AB-2016 standards-track module defining the second-generation Link Layer Discovery Protocol objects, supporting the newer architecture where multiple LLDP agents on a single port can each transmit using a different MAC address. It exposes global and per-port LLDP configuration (transmit interval, hold multiplier, reinitialization delay, notification interval, fast-transmit parameters) as well as local system data and remote (neighbor) system data used for topology discovery. Its monitoring role is chiefly topology and configuration status — confirming LLDP is enabled and correctly timed on each port, and, via the neighbor tables it maintains, detecting unexpected new neighbors, missing expected neighbors, or topology changes that could indicate a mis-cabled or newly connected device. It supersedes and extends the original LLDP-MIB while remaining layered on standard IF-MIB interface indexing for port association. It is deployed on essentially any modern LLDP-capable switch, router, or endpoint device used for automated network topology discovery and inventory, and network engineers often consult the LLDP-V2-MIB reference alongside IEEE 802.1AB-2016 when mapping objects to the legacy LLDP-MIB.

IPNetwork Monitor allows you to monitor SNMP objects defined in LLDP-V2-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

vendor-neutral, standards-based MIB, not tied to a specific manufacturer
any LLDP-capable switch, router, or network endpoint

Monitoring Examples

An administrator would poll lldpV2PortConfigTable (lldpV2PortConfigEntry, keyed by lldpV2PortConfigIfIndex and lldpV2PortConfigDestAddressIndex) to confirm lldpV2PortConfigAdminStatus is enabled on expected ports, alongside global timers like lldpV2MessageTxInterval and lldpV2ReinitDelay; combined with the lldpV2Notifications trap group, an unexpected change in a port's LLDP admin status or a burst of topology-change notifications would flag a newly connected, disconnected, or mis-cabled neighbor device.

What Can Be Monitored

LLDP port admin status (enabled/disabled)
LLDP transmit interval and hold multiplier
reinitialization delay
notification interval
topology/neighbor change notifications

Imported Objects

From IANA-ADDRESS-FAMILY-NUMBERS-MIB

AddressFamilyNumbers

From IF-MIB

InterfaceIndex
ifGeneralInformationGroup	OBJECT-GROUP

From LLDP-V2-TC-MIB

LldpV2ChassisId
LldpV2ChassisIdSubtype
LldpV2DestAddressTableIndex
LldpV2ManAddrIfSubtype
LldpV2ManAddress
LldpV2PortId
LldpV2PortIdSubtype
LldpV2SystemCapabilitiesMap
ieee802dot1mibs	OBJECT-IDENTITY

From RMON2-MIB

TimeFilter
ZeroBasedCounter32

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

MacAddress
RowStatus
TimeStamp
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
ADR lldpV2AddressTableIndex	1.3.111.2.802.1.1.13.1.1.9.1.1	LldpV2DestAddressTableIndex	not-accessible	The index value used to identify the destination MAC address associated with this entry. The value of this object is used as an index to the lldpV2DestAddressTable.
lldpV2Compliances	1.3.111.2.802.1.1.13.2.1
lldpV2ConfigGroup	1.3.111.2.802.1.1.13.2.2.1			The collection of objects that are used to configure the LLDP implementation behavior.
lldpV2ConfigRxGroup	1.3.111.2.802.1.1.13.2.2.2			The collection of objects that are used to configure the LLDP reception implementation behavior.
lldpV2ConfigTxGroup	1.3.111.2.802.1.1.13.2.2.3			The collection of objects that are used to configure the LLDP transmission implementation behavior.
lldpV2Configuration	1.3.111.2.802.1.1.13.1.1
lldpV2Conformance	1.3.111.2.802.1.1.13.2
lldpV2DestAddressTable	1.3.111.2.802.1.1.13.1.1.9		not-accessible	The table that contains the set of MAC addresses used by LLDP for transmission and reception of LLDPDUs.
lldpV2DestAddressTableEntry	1.3.111.2.802.1.1.13.1.1.9.1		not-accessible	Destination MAC address information for LLDP. This configuration parameter identifies a MAC address corresponding to a LldpV2DestAddressTableIndex value. Rows in this table are created as necessary, to support MAC addresses needed by other tables in the MIB that are indexed by MAC address. A given row in this table cannot be deleted if the MAC address table index value is in use in any other table in the MIB. The contents of this table are persistent across re-initializations or re-boots.
MAC lldpV2DestMacAddress	1.3.111.2.802.1.1.13.1.1.9.1.2	MacAddress	read-only	The MAC address associated with this entry. The octet string identifies an individual or a group MAC address that is in use by LLDP as a destination MAC address. The MAC address is encoded in the octet string in canonical format (see IEEE Std 802).
lldpV2Extensions	1.3.111.2.802.1.1.13.1.5
lldpV2Groups	1.3.111.2.802.1.1.13.2.2
lldpV2LocalSystemData	1.3.111.2.802.1.1.13.1.3
LLD lldpV2LocChassisId	1.3.111.2.802.1.1.13.1.3.2	LldpV2ChassisId	read-only	The string value used to identify the chassis component associated with the local system.
LLD lldpV2LocChassisIdSubtype	1.3.111.2.802.1.1.13.1.3.1	LldpV2ChassisIdSubtype	read-only	The type of encoding used to identify the chassis associated with the local system.
ADR lldpV2LocManAddr	1.3.111.2.802.1.1.13.1.3.8.1.2	LldpV2ManAddress	not-accessible	The string value used to identify the management address component associated with the local system. The purpose of this address is to contact the management entity.
lldpV2LocManAddrEntry	1.3.111.2.802.1.1.13.1.3.8.1		not-accessible	Management address information about a particular chassis component. There may be multiple management addresses configured on the system identified by a particular lldpLocChassisId. Each management address should have distinct 'management address type' (lldpV2LocManAddrSubtype) and 'management address' (lldpLocManAddr.) Entries may be created and deleted in this table by the agent. Since a variable length octetstring is used as an index in a table, the address length is encoded as part of the OID (as per IETF RFC 2578).
U32 lldpV2LocManAddrIfId	1.3.111.2.802.1.1.13.1.3.8.1.5	Unsigned32	read-only	The integer value used to identify the interface number regarding the management address component associated with the local system.
LLD lldpV2LocManAddrIfSubtype	1.3.111.2.802.1.1.13.1.3.8.1.4	LldpV2ManAddrIfSubtype	read-only	The enumeration value that identifies the interface numbering method used for defining the interface number (lldpV2LocManAddrIfId), associated with the local system.
U32 lldpV2LocManAddrLen	1.3.111.2.802.1.1.13.1.3.8.1.3	Unsigned32	read-only	The total length of the management address subtype and the management address fields in LLDPDUs transmitted by the local LLDP agent. The management address length field is needed so that the receiving systems that do not implement SNMP are not required to implement an Internet Assigned Numbers Authority (IANA) family numbers/address length equivalency table in order to decode the management address.
OID lldpV2LocManAddrOID	1.3.111.2.802.1.1.13.1.3.8.1.6	OBJECT IDENTIFIER	read-only	The OID value used to identify the type of hardware component or protocol entity associated with the management address advertised by the local system agent.
ADR lldpV2LocManAddrSubtype	1.3.111.2.802.1.1.13.1.3.8.1.1	AddressFamilyNumbers	not-accessible	The type of management address identifier encoding used in the associated 'lldpLocManagmentAddr' object. It should be noted that only a subset of the possible address encodings enumerated in AddressFamilyNumbers are appropriate for use as a LLDP management address, either because some are just not applicable or because the maximum size of a LldpV2ManAddress octet string would prevent the use of some address identifier encodings.
lldpV2LocManAddrTable	1.3.111.2.802.1.1.13.1.3.8		not-accessible	This table contains management address information on the local system known to this agent.
STR lldpV2LocPortDesc	1.3.111.2.802.1.1.13.1.3.7.1.4	SnmpAdminString	read-only	The string value used to identify the IEEE 802 LAN station's port description associated with the local system. If the local agent supports IETF RFC 2863, lldpLocPortDesc object should have the same value of ifDescr object.
lldpV2LocPortEntry	1.3.111.2.802.1.1.13.1.3.7.1		not-accessible	Information about a particular port component. Entries may be created and deleted in this table by the agent. Rows in this table can only be created for MAC addresses that can validly be used in association with the type of interface concerned, as defined by Table 7-2. The contents of this table is persistent across re-initializations or re-boots.
LLD lldpV2LocPortId	1.3.111.2.802.1.1.13.1.3.7.1.3	LldpV2PortId	read-only	The string value used to identify the port component associated with a given port in the local system.
LLD lldpV2LocPortIdSubtype	1.3.111.2.802.1.1.13.1.3.7.1.2	LldpV2PortIdSubtype	read-only	The type of port identifier encoding used in the associated 'lldpLocPortId' object.
NUM lldpV2LocPortIfIndex	1.3.111.2.802.1.1.13.1.3.7.1.1	InterfaceIndex	not-accessible	The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB. The value of this object is used as an index to the lldpV2LocPortTable.
lldpV2LocPortTable	1.3.111.2.802.1.1.13.1.3.7		not-accessible	This table contains one row per port of information associated with the local system known to this agent.
LLD lldpV2LocSysCapEnabled	1.3.111.2.802.1.1.13.1.3.6	LldpV2SystemCapabilitiesMap	read-only	The bitmap value used to identify which system capabilities are enabled on the local system.
LLD lldpV2LocSysCapSupported	1.3.111.2.802.1.1.13.1.3.5	LldpV2SystemCapabilitiesMap	read-only	The bitmap value used to identify which system capabilities are supported on the local system.
STR lldpV2LocSysDesc	1.3.111.2.802.1.1.13.1.3.4	SnmpAdminString	read-only	The string value used to identify the system description of the local system. If the local agent supports IETF RFC 3418, lldpLocSysDesc object should have the same value as sysDesc object.
lldpV2LocSysGroup	1.3.111.2.802.1.1.13.2.2.6			The collection of objects that are used to represent LLDP Local System Information.
STR lldpV2LocSysName	1.3.111.2.802.1.1.13.1.3.3	SnmpAdminString	read-only	The string value used to identify the system name of the local system. If the local agent supports IETF RFC 3418, lldpLocSysName object should have the same value as sysName object.
ADR lldpV2ManAddrConfigDestAddressIndex	1.3.111.2.802.1.1.13.1.1.10.1.2	LldpV2DestAddressTableIndex	not-accessible	The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the lldpV2PortConfigTable.
NUM lldpV2ManAddrConfigIfIndex	1.3.111.2.802.1.1.13.1.1.10.1.1	InterfaceIndex	not-accessible	The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB. The value of this object is used as an index to the lldpV2PortConfigTable. The value in this column of the table MUST match the IfIndex value specified in the BridgePort table.
ADR lldpV2ManAddrConfigLocManAddr	1.3.111.2.802.1.1.13.1.1.10.1.4	LldpV2ManAddress	not-accessible	The string value used to identify the management address component associated with the local system. The purpose of this address is to contact the management entity.
ADR lldpV2ManAddrConfigLocManAddrSubtype	1.3.111.2.802.1.1.13.1.1.10.1.3	AddressFamilyNumbers	not-accessible	The type of management address identifier encoding used in the associated 'lldpLocManagmentAddr' object. It should be noted that only a subset of the possible address encodings enumerated in AddressFamilyNumbers are appropriate for use as a LLDP management address, either because some are just not applicable or because the maximum size of a LldpV2ManAddress octet string would prevent the use of some address identifier encodings.
ROW lldpV2ManAddrConfigRowStatus	1.3.111.2.802.1.1.13.1.1.10.1.6	RowStatus	read-create	Indicates the status of an entry in this table, and is used to create/delete entries. The corresponding instances of the following objects must be set before this object can be made active(1): lldpV2ManAddrConfigDestAddressIndex lldpV2ManAddrConfigLocManAddrSubtype lldpV2ManAddrConfigLocManAddr lldpV2ManAddrConfigTxEnable The corresponding instances of the following objects may not be changed while this object is active(1): lldpV2ManAddrConfigDestAddressIndex lldpV2ManAddrConfigLocManAddrSubtype lldpV2ManAddrConfigLocManAddr
T/F lldpV2ManAddrConfigTxEnable	1.3.111.2.802.1.1.13.1.1.10.1.5	TruthValue	read-create	A Boolean controlling the transmission of system management address instance for the specified port, destination, subtype, and MAN address used to index this table. If set to the default value of false, no transmission occurs. If set to true, the appropriate information is transmitted out of the port specified in the row's index.
lldpV2ManAddrConfigTxPortsEntry	1.3.111.2.802.1.1.13.1.1.10.1		not-accessible	LLDP configuration information that specifies the set of port/destination address pairs on which the local system management address instance is transmitted. Each active lldpManAddrConfigTxPortsTableV2Entry is restored from non-volatile storage and re-created after a re-initialization of the management system.
lldpV2ManAddrConfigTxPortsTable	1.3.111.2.802.1.1.13.1.1.10		not-accessible	The table that controls selection of LLDP management address TLV instances to be transmitted on individual port/ destination address pairs.
U32 lldpV2MessageFastTx	1.3.111.2.802.1.1.13.1.1.6	Unsigned32	read-write	The interval at which LLDP frames are transmitted on behalf of this LLDP agent during fast transmission period (e.g., when a new neighbor is detected). The default value for lldpV2MessageFastTx object is 1 second. The value of this object is used as the initial value of the lldpV2PortMessageFastTx object on row creation in the lldpV2PortConfigTableV2. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
U32 lldpV2MessageTxHoldMultiplier	1.3.111.2.802.1.1.13.1.1.2	Unsigned32	read-write	The time to live value expressed as a multiple of the lldpV2MessageTxInterval object. The actual time to live value used in LLDP frames, transmitted on behalf of this LLDP agent, can be expressed by the following formula: TTL = min(65535, (lldpV2MessageTxInterval*lldpV2MessageTxHoldMultiplier)+1) For example, if the value of lldpV2MessageTxInterval is '30', and the value of lldpV2MessageTxHoldMultiplier is '4', then the value '121' is encoded in the TTL field in the LLDP header. The default value for lldpV2MessageTxHoldMultiplier object is 4. The value of this object is used as the initial value of the lldpV2PortMessageTxHoldMultiplier object on row creation in the lldpV2PortConfigTableV2. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
U32 lldpV2MessageTxInterval	1.3.111.2.802.1.1.13.1.1.1	Unsigned32	read-write	The interval at which LLDP frames are transmitted on behalf of this LLDP agent. The default value for lldpV2MessageTxInterval object is 30 seconds. The value of this object is used as the initial value of the lldpV2PortMessageTxInterval object on row creation in the lldpV2PortConfigTableV2. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
lldpV2MIB	1.3.111.2.802.1.1.13			Management Information Base module for LLDP configuration, statistics, local system data and remote systems data components. This MIB module supports the architecture described in Clause 6, where multiple LLDP agents can be associated with a single Port, each supporting transmission by means of a different MAC address. Unless otherwise indicated, the references in this MIB module are to IEEE Std 802.1AB-2016. Copyright (C) IEEE (2016). This version of this MIB module is published as 11.5.2 of IEEE Std 802.1AB-2016; see the standard itself for full legal notices.
U32 lldpV2NotificationInterval	1.3.111.2.802.1.1.13.1.1.4	Unsigned32	read-write	This object controls the interval between transmission of LLDP notifications during normal transmission periods. The value of this object is used as the initial value of the lldpV2PortNotificationInterval object on row creation in the lldpV2PortConfigTableV2. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
lldpV2NotificationPrefix	1.3.111.2.802.1.1.13.0.0
lldpV2Notifications	1.3.111.2.802.1.1.13.0
lldpV2NotificationsGroup	1.3.111.2.802.1.1.13.2.2.8			The collection of notifications used to indicate LLDP MIB data consistency and general status information.
lldpV2Objects	1.3.111.2.802.1.1.13.1
INT lldpV2PortConfigAdminStatus	1.3.111.2.802.1.1.13.1.1.8.1.3	INTEGER	read-write	The administratively desired status of the local LLDP agent. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'txOnly(1)', then LLDP agent transmits LLDPframes on this port and it does not store any information about the remote systems connected. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'rxOnly(2)', then the LLDP agent receives, but it does not transmit LLDP frames on this port. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'txAndRx(3)', then the LLDP agent transmits and receives LLDP frames on this port. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'disabled(4)', then LLDP agent does not transmit or receive LLDP frames on this port. If there is remote systems information that is received on this port and stored in other tables, before the port's lldpV2PortConfigAdminStatus becomes disabled, then that information is deleted.
INT lldpV2PortConfigAdminStatusV2	1.3.111.2.802.1.1.13.1.1.11.1.3	INTEGER	read-write	The administratively desired status of the local LLDP agent. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'txOnly(1)', then LLDP agent transmits LLDPframes on this port and it does not store any information about the remote systems connected. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'rxOnly(2)', then the LLDP agent receives, but it does not transmit, LLDP frames on this port. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'txAndRx(3)', then the LLDP agent transmits and receives LLDP frames on this port. If the associated lldpV2PortConfigAdminStatus object is set to a value of 'disabled(4)', then LLDP agent does not transmit or receive LLDP frames on this port. If there is remote systems information that is received on this port and stored in other tables, before the port's lldpV2PortConfigAdminStatus becomes disabled, then that information is deleted.
ADR lldpV2PortConfigDestAddressIndex	1.3.111.2.802.1.1.13.1.1.8.1.2	LldpV2DestAddressTableIndex	not-accessible	The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the lldpV2PortConfigTable.
ADR lldpV2PortConfigDestAddressIndexV2	1.3.111.2.802.1.1.13.1.1.11.1.2	LldpV2DestAddressTableIndex	not-accessible	The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the lldpV2PortConfigTable.
lldpV2PortConfigEntry	1.3.111.2.802.1.1.13.1.1.8.1		not-accessible	LLDP configuration information for a particular port and destination MAC address. This configuration parameter controls the transmission and the reception of LLDP frames on those interface/address combinations whose rows are created in this table. Rows in this table can only be created for MAC addresses that can validly be used in association with the type of interface concerned, as defined by Table 7-2. The contents of this table is persistent across re-initializations or re-boots.
lldpV2PortConfigEntryV2	1.3.111.2.802.1.1.13.1.1.11.1		not-accessible	LLDP configuration information for a particular port and destination MAC address. This configuration parameter controls the transmission and the reception of LLDP frames on those interface/address combinations whose rows are created in this table. Rows in this table can only be created for MAC addresses that can validly be used in association with the type of interface concerned, as defined by Table 7-2. The contents of this table is persistent across re-initializations or re-boots.
NUM lldpV2PortConfigIfIndex	1.3.111.2.802.1.1.13.1.1.8.1.1	InterfaceIndex	not-accessible	The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB. The value of this object is used as an index to the lldpV2PortConfigTable.
NUM lldpV2PortConfigIfIndexV2	1.3.111.2.802.1.1.13.1.1.11.1.1	InterfaceIndex	not-accessible	The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB. The value of this object is used as an index to the lldpV2PortConfigTable.
T/F lldpV2PortConfigNotificationEnable	1.3.111.2.802.1.1.13.1.1.8.1.4	TruthValue	read-write	The lldpV2PortConfigNotificationEnable controls, on a per agent basis, whether or not notifications from the agent are enabled. The value true(1) means that notifications are enabled; the value false(2) means that they are not.
T/F lldpV2PortConfigNotificationEnableV2	1.3.111.2.802.1.1.13.1.1.11.1.11	TruthValue	read-write	The lldpV2PortConfigNotificationEnableV2 controls, on a per agent basis, whether or not notifications from the agent are enabled. The value true(1) means that notifications are enabled; the value false(2) means that they are not.
lldpV2PortConfigTable	1.3.111.2.802.1.1.13.1.1.8		not-accessible	The table that controls LLDP frame transmission on individual ports that uses particular destination MAC addresses.
lldpV2PortConfigTableV2	1.3.111.2.802.1.1.13.1.1.11		not-accessible	The table that controls LLDP frame transmission on individual ports and using particular destination MAC addresses.
BIT lldpV2PortConfigTLVsTxEnable	1.3.111.2.802.1.1.13.1.1.8.1.5	Bits	read-write	The lldpV2PortConfigTLVsTxEnable, defined as a bitmap, includes the basic set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to a TLV type associated with a specific optional TLV. It should be noted that the organizationally-specific TLVs are excluded from the lldpV2PortConfigTLVsTxEnable bitmap. LLDP Organization Specific Information Extension MIBs should have similar configuration objects to control transmission of their organizationally defined TLVs. The bit 'portDesc(0)' indicates that LLDP agent should transmit 'Port Description TLV'. The bit 'sysName(1)' indicates that LLDP agent should transmit 'System Name TLV'. The bit 'sysDesc(2)' indicates that LLDP agent should transmit 'System Description TLV'. The bit 'sysCap(3)' indicates that LLDP agent should transmit 'System Capabilities TLV'. There is no bit reserved for the management address TLV type since transmission of management address TLVs are controlled by another object, lldpV2ConfigManAddrTable. The default value for lldpV2PortConfigTLVsTxEnable object is empty set, which means no enumerated values are set. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
BIT lldpV2PortConfigTLVsTxEnableV2	1.3.111.2.802.1.1.13.1.1.11.1.12	Bits	read-write	The lldpV2PortConfigTLVsTxEnableV2, defined as a bitmap, includes the basic set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to a TLV type associated with a specific optional TLV. It should be noted that the organizationally-specific TLVs are excluded from the lldpV2PortConfigTLVsTxEnable bitmap. LLDP Organization Specific Information Extension MIBs should have similar configuration objects to control transmission of their organizationally defined TLVs. The bit 'portDesc(0)' indicates that LLDP agent should transmit 'Port Description TLV'. The bit 'sysName(1)' indicates that LLDP agent should transmit 'System Name TLV'. The bit 'sysDesc(2)' indicates that LLDP agent should transmit 'System Description TLV'. The bit 'sysCap(3)' indicates that LLDP agent should transmit 'System Capabilities TLV'. There is no bit reserved for the management address TLV type since transmission of management address TLVs are controlled by another object, lldpV2ConfigManAddrTable. The default value for lldpV2PortConfigTLVsTxEnable object is empty set, which means no enumerated values are set. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
U32 lldpV2PortMessageFastTx	1.3.111.2.802.1.1.13.1.1.11.1.9	Unsigned32	read-write	The interval at which LLDP frames are transmitted on behalf of this LLDP agent during fast transmission period (e.g., when a new neighbor is detected). This object takes its initial value from the lldpV2PortMessageFastTx object on table row creation. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
U32 lldpV2PortMessageTxHoldMultiplier	1.3.111.2.802.1.1.13.1.1.11.1.5	Unsigned32	read-write	The time to live value expressed as a multiple of the lldpV2MessageTxInterval object. The actual time to live value used in LLDP frames, transmitted on behalf of this LLDP agent, can be expressed by the following formula: TTL = min(65535, (lldpV2MessageTxInterval*lldpV2MessageTxHoldMultiplier)+1) For example, if the value of lldpV2MessageTxInterval is '30', and the value of lldpV2MessageTxHoldMultiplier is '4', then the value '121' is encoded in the TTL field in the LLDP header. This object takes its initial value from the lldpV2PortMessageTxHoldMultiplier object on table row creation. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
U32 lldpV2PortMessageTxInterval	1.3.111.2.802.1.1.13.1.1.11.1.4	Unsigned32	read-write	The interval at which LLDP frames are transmitted on behalf of this LLDP agent. This object takes its initial value from the lldpV2MessageTxInterval object on table row creation. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
U32 lldpV2PortNotificationInterval	1.3.111.2.802.1.1.13.1.1.11.1.7	Unsigned32	read-write	This object controls the interval between transmission of LLDP notifications during normal transmission periods. This object takes its initial value from the lldpV2PortNotificationInterval object on table row creation. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
U32 lldpV2PortReinitDelay	1.3.111.2.802.1.1.13.1.1.11.1.6	Unsigned32	read-write	The lldpV2ReinitDelay indicates the delay (in units of seconds) from when lldpPortConfigAdminStatus object of a particular port becomes 'disabled' until re-initialization is attempted. This object takes its initial value from the lldpV2PortReinitDelay object on table row creation. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
U32 lldpV2PortTxCreditMax	1.3.111.2.802.1.1.13.1.1.11.1.8	Unsigned32	read-write	The maximum number of consecutive LLDPDUs that can be transmitted at any time. This object takes its initial value from the lldpV2PortTxCreditMax object on table row creation. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
U32 lldpV2PortTxFastInit	1.3.111.2.802.1.1.13.1.1.11.1.10	Unsigned32	read-write	The initial value used to initialize the txFast variable which determines the number of transmissions that are made in fast transmission mode. This object takes its initial value from the lldpV2PortTxFastInit object on table row creation. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
U32 lldpV2ReinitDelay	1.3.111.2.802.1.1.13.1.1.3	Unsigned32	read-write	The lldpV2ReinitDelay indicates the delay (in units of seconds) from when lldpPortConfigAdminStatus object of a particular port becomes 'disabled' until re-initialization is attempted. The default value for lldpV2ReinitDelay is 2 s. The value of this object is used as the initial value of the lldpV2PortReinitDelay object on row creation in the lldpV2PortConfigTableV2. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
LLD lldpV2RemChassisId	1.3.111.2.802.1.1.13.1.4.1.1.6	LldpV2ChassisId	read-only	The string value used to identify the chassis component associated with the remote system.
LLD lldpV2RemChassisIdSubtype	1.3.111.2.802.1.1.13.1.4.1.1.5	LldpV2ChassisIdSubtype	read-only	The type of encoding used to identify the chassis associated with the remote system.
lldpV2RemEntry	1.3.111.2.802.1.1.13.1.4.1.1		not-accessible	Information about a particular physical network connection. Entries may be created and deleted in this table by the agent, if a physical topology discovery process is active. Rows in this table can only be created for MAC addresses that can validly be used in association with the type of interface concerned, as defined by Table 7-2. The contents of this table is persistent across re-initializations or re-boots.
U32 lldpV2RemIndex	1.3.111.2.802.1.1.13.1.4.1.1.4	Unsigned32	not-accessible	This object represents an arbitrary local integer value used by this agent to identify a particular connection instance, unique only for the indicated remote system. An agent is encouraged to assign monotonically increasing index values to new entries, starting with one, after each reboot. It is considered unlikely that the lldpRemIndex can wrap between reboots.
ADR lldpV2RemLocalDestMACAddress	1.3.111.2.802.1.1.13.1.4.1.1.3	LldpV2DestAddressTableIndex	not-accessible	The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the lldpV2RemTable.
NUM lldpV2RemLocalIfIndex	1.3.111.2.802.1.1.13.1.4.1.1.2	InterfaceIndex	not-accessible	The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB The value of this object is used as an index to the lldpV2RemTable.
ADR lldpV2RemManAddr	1.3.111.2.802.1.1.13.1.4.2.1.2	LldpV2ManAddress	not-accessible	The string value used to identify the management address component associated with the remote system. The purpose of this address is to contact the management entity.
lldpV2RemManAddrEntry	1.3.111.2.802.1.1.13.1.4.2.1		not-accessible	Management address information about a particular chassis component. There may be multiple management addresses configured on the remote system identified by a particular lldpRemIndex whose information is received on an interface of the local system and a given destination MAC address. Each management address should have distinct 'management address type' (lldpRemManAddrSubtype) and 'management address' (lldpRemManAddr). Entries may be created and deleted in this table by the agent. Since a variable length octetstring is used as an index in a table, theaddress length is encoded as part of the OID (as per IETF RFC 2578).
U32 lldpV2RemManAddrIfId	1.3.111.2.802.1.1.13.1.4.2.1.4	Unsigned32	read-only	The integer value used to identify the interface number regarding the management address component associated with the remote system. The value depends upon the value of the lldpV2RemManAddrIfSubtype for the table row.
LLD lldpV2RemManAddrIfSubtype	1.3.111.2.802.1.1.13.1.4.2.1.3	LldpV2ManAddrIfSubtype	read-only	The enumeration value that identifies the interface numbering method used for defining the interface number, associated with the remote system.
OID lldpV2RemManAddrOID	1.3.111.2.802.1.1.13.1.4.2.1.5	OBJECT IDENTIFIER	read-only	The OID value used to identify the type of hardware component or protocol entity associated with the management address advertised by the remote system agent.
ADR lldpV2RemManAddrSubtype	1.3.111.2.802.1.1.13.1.4.2.1.1	AddressFamilyNumbers	not-accessible	The type of management address identifier encoding used in the associated 'lldpRemManagmentAddr' object. It should be noted that only a subset of the possible address encodings enumerated in AddressFamilyNumbers are appropriate for use as a LLDP management address, either because some are just not apliccable or because the maximum size of a LldpV2ManAddress octet string would prevent the use of some address identifier encodings.
lldpV2RemManAddrTable	1.3.111.2.802.1.1.13.1.4.2		not-accessible	This table contains one or more rows per management address information on the remote system learned on a particular port contained in the local chassis known to this agent.
OCT lldpV2RemOrgDefInfo	1.3.111.2.802.1.1.13.1.4.4.1.4	OCTET STRING	read-only	The string value used to identify the organizationally defined information of the remote system. The encoding for this object should be as defined for SnmpAdminString TC.
lldpV2RemOrgDefInfoEntry	1.3.111.2.802.1.1.13.1.4.4.1		not-accessible	Information about the unrecognized organizationally defined information advertised by the remote system. The lldpRemTimeMark, lldpRemLocalPortNum, lldpRemIndex, lldpRemOrgDefInfoOUI, lldpRemOrgDefInfoSubtype, and lldpRemOrgDefInfoIndex are indexes to this table. If there is an lldpRemOrgDefInfoEntry associated with a particular remote system identified by the lldpRemLocalPortNum and lldpRemIndex, then there is an lldpRemEntry associated with the same instance (i.e., using same indexes.) When the lldpRemEntry for the same index is removed from the lldpRemTable, the associated lldpRemOrgDefInfoEntry is removed from the lldpRemOrgDefInfoTable. Entries may be created and deleted in this table by the agent.
U32 lldpV2RemOrgDefInfoIndex	1.3.111.2.802.1.1.13.1.4.4.1.3	Unsigned32	not-accessible	This object represents an arbitrary local integer value used by this agent to identify a particular unrecognized organizationally defined information instance, unique only for the lldpRemOrgDefInfoOUI and lldpRemOrgDefInfoSubtype from the same remote system. An agent is encouraged to assign monotonically increasing index values to new entries, starting with one, after each reboot. It is considered unlikely that the lldpRemOrgDefInfoIndex can wrap between reboots.
OCT lldpV2RemOrgDefInfoOUI	1.3.111.2.802.1.1.13.1.4.4.1.1	OCTET STRING	not-accessible	The Organizationally Unique Identifier (OUI), as defined in IEEE Std 802, is a 24 bit (three octets) globally unique assigned number referenced by various standards, of the information received from the remote system.
U32 lldpV2RemOrgDefInfoSubtype	1.3.111.2.802.1.1.13.1.4.4.1.2	Unsigned32	not-accessible	The integer value used to identify the subtype of the organizationally defined information received from the remote system. The subtype value is required to identify different instances of organizationally defined information that could not be retrieved without a unique identifier that indicates the particular type of information contained in the information string.
lldpV2RemOrgDefInfoTable	1.3.111.2.802.1.1.13.1.4.4		not-accessible	This table contains one or more rows per physical network connection which advertises the organizationally defined information. Note that this table contains one or more rows of organizationally defined information that is not recognized by the local agent. If the local system is capable of recognizing any organizationally defined information, appropriate extension MIBs from the organization should be used for information retrieval.
lldpV2RemoteSystemsData	1.3.111.2.802.1.1.13.1.4
STR lldpV2RemPortDesc	1.3.111.2.802.1.1.13.1.4.1.1.9	SnmpAdminString	read-only	The string value used to identify the description of the given port associated with the remote system.
LLD lldpV2RemPortId	1.3.111.2.802.1.1.13.1.4.1.1.8	LldpV2PortId	read-only	The string value used to identify the port component associated with the remote system.
LLD lldpV2RemPortIdSubtype	1.3.111.2.802.1.1.13.1.4.1.1.7	LldpV2PortIdSubtype	read-only	The type of port identifier encoding used in the associated 'lldpRemPortId' object.
T/F lldpV2RemRemoteChanges	1.3.111.2.802.1.1.13.1.4.1.1.14	TruthValue	read-only	Indicates that there are changes in the remote systems MIB, as determined by the variable remoteChanges.
LLD lldpV2RemSysCapEnabled	1.3.111.2.802.1.1.13.1.4.1.1.13	LldpV2SystemCapabilitiesMap	read-only	The bitmap value used to identify which system capabilities are enabled on the remote system.
LLD lldpV2RemSysCapSupported	1.3.111.2.802.1.1.13.1.4.1.1.12	LldpV2SystemCapabilitiesMap	read-only	The bitmap value used to identify which system capabilities are supported on the remote system.
STR lldpV2RemSysDesc	1.3.111.2.802.1.1.13.1.4.1.1.11	SnmpAdminString	read-only	The string value used to identify the system description of the remote system.
lldpV2RemSysGroup	1.3.111.2.802.1.1.13.2.2.7			The collection of objects that are used to represent LLDP Remote Systems Information. The objects represent the information associated with the basic TLV set. Please note that even if the agent does not implement some of the optional TLVs, it shall recognize all the optional TLV information that the remote system may advertise.
STR lldpV2RemSysName	1.3.111.2.802.1.1.13.1.4.1.1.10	SnmpAdminString	read-only	The string value used to identify the system name of the remote system.
lldpV2RemTable	1.3.111.2.802.1.1.13.1.4.1		not-accessible	This table contains one or more rows per physical network connection known to this agent. The agent may wish to ensure that only one lldpRemEntry is present for each local port and destination MAC address, or it may choose to maintain multiple lldpRemEntries for the same local port and destination MAC address. The following procedure may be used to retrieve remote systems information updates from an LLDP agent: 1. NMS polls all tables associated with remote systems and keeps a local copy of the information retrieved. NMS polls periodically the values of the following objects: a. lldpV2StatsRemTablesInserts b. lldpV2StatsRemTablesDeletes c. lldpV2StatsRemTablesDrops d. lldpV2StatsRemTablesAgeouts e. lldpV2StatsRxPortAgeoutsTotal for all ports. 2. LLDP agent updates remote systems MIB objects, and sends out notifications to a list of notification destinations. 3. NMS receives the notifications and compares the new values of objects listed in step 1. Periodically, NMS should poll the object lldpV2StatsRemTablesLastChangeTime to find out if anything has changed since the last poll. If something has changed, NMS polls the objects listed in step 1 to figure out what kind of changes occurred in the tables. If value of lldpV2StatsRemTablesInserts has changed, then NMS walks all tables by employing TimeFilter with the last-polled time value. This request returns new objects or objects whose values have been updated since the last poll. If value of lldpV2StatsRemTablesAgeouts has changed, then NMS walks the lldpStatsRxPortAgeoutsTotal and compares the new values with previously recorded ones. For ports whose lldpStatsRxPortAgeoutsTotal value is greater than the recorded value, NMS can retrieve objects associated with those ports from table(s) without employing a TimeFilter (which is performed by specifying 0 for the TimeFilter). lldpV2StatsRemTablesDeletes and lldpV2StatsRemTablesDrops objects are provided for informational purposes.
NTF lldpV2RemTablesChange	1.3.111.2.802.1.1.13.0.0.1			A lldpV2RemTablesChange notification is sent when the value of lldpV2StatsRemTablesLastChangeTime changes. It can be utilized by an NMS to trigger LLDP remote systems table maintenance polls. Note that transmission of lldpV2RemTablesChange notifications are throttled by the agent, as specified by the 'lldpV2NotificationInterval' object.
TIM lldpV2RemTimeMark	1.3.111.2.802.1.1.13.1.4.1.1.1	TimeFilter	not-accessible	A TimeFilter for this entry. See the TimeFilter textual convention in IETF RFC 4502 and http://www.ietf.org/IESG/Implementations/RFC2021-Implementation.txt to see how TimeFilter works.
T/F lldpV2RemTooManyNeighbors	1.3.111.2.802.1.1.13.1.4.1.1.15	TruthValue	read-only	Indicates that there are too many neighbors as determined by the variable tooManyNeighbors.
lldpV2RemUnknownTLVEntry	1.3.111.2.802.1.1.13.1.4.3.1		not-accessible	Information about an unrecognized TLV received from a physical network connection. Entries may be created and deleted in this table by the agent, if a physical topology discovery process is active.
OCT lldpV2RemUnknownTLVInfo	1.3.111.2.802.1.1.13.1.4.3.1.2	OCTET STRING	read-only	This object represents the value extracted from the value field of the TLV.
lldpV2RemUnknownTLVTable	1.3.111.2.802.1.1.13.1.4.3		not-accessible	This table contains information about an incoming TLV that is not recognized by the receiving LLDP agent. The TLV may be from a later version of the basic management set. This table should only contain TLVs that are found in a single LLDP frame. Entries in this table, associated with an MAC service access point (MSAP, the access point for MAC services provided to the LCC sublayer, defined in IEEE Standards Dictionary Online, which is also identified with a particular lldpRemLocalPortNum, lldpRemIndex pair) are overwritten with most recently received unrecognized TLV from the same MSAP, or they naturally age out when the rxInfoTTL timer (associated with the MSAP) expires.
U32 lldpV2RemUnknownTLVType	1.3.111.2.802.1.1.13.1.4.3.1.1	Unsigned32	not-accessible	This object represents the value extracted from the type field of the TLV.
lldpV2RxCompliance	1.3.111.2.802.1.1.13.2.1.3			The compliance statement for SNMP entities that implement the LLDP MIB and have the capability of receiving LLDP frames. This version defines compliance requirements for V2 of the LLDP MIB module.
lldpV2Statistics	1.3.111.2.802.1.1.13.1.2
NUM lldpV2StatsRemTablesAgeouts	1.3.111.2.802.1.1.13.1.2.5	ZeroBasedCounter32	read-only	The number of times the complete set of information advertised by a particular MSAP has been deleted from tables contained in lldpV2RemoteSystemsData and lldpV2Extensions objects because the information timeliness interval has expired. This counter should be incremented only once when the complete set of information is completely invalidated (aged out) from all related tables. Partial ageing, similar to deletion case, is not allowed, and thus, should not change the value of this counter.
NUM lldpV2StatsRemTablesDeletes	1.3.111.2.802.1.1.13.1.2.3	ZeroBasedCounter32	read-only	The number of times the complete set of information advertised by a particular MSAP has been deleted from tables contained in lldpV2RemoteSystemsData and lldpV2Extensions objects. This counter should be incremented only once when the complete set of information is completely deleted from all related tables. Partial deletions, such as deletion of rows associated with a particular MSAP from some tables, but not from all tables are not allowed, thus should not change the value of this counter.
NUM lldpV2StatsRemTablesDrops	1.3.111.2.802.1.1.13.1.2.4	ZeroBasedCounter32	read-only	The number of times the complete set of information advertised by a particular MSAP could not be entered into tables contained in lldpV2RemoteSystemsData and lldpV2Extensions objects because of insufficient resources.
NUM lldpV2StatsRemTablesInserts	1.3.111.2.802.1.1.13.1.2.2	ZeroBasedCounter32	read-only	The number of times the complete set of information advertised by a particular MSAP has been inserted into tables contained in lldpV2RemoteSystemsData and lldpV2Extensions objects. The complete set of information received from a particular MSAP should be inserted into related tables. If partial information cannot be inserted for a reason such as lack of resources, all of the complete set of information should be removed. This counter should be incremented only once after the complete set of information is successfully recorded in all related tables. Any failures during inserting information set that result in deletion of previously inserted information should not trigger any changes in lldpV2StatsRemTablesInserts since the insert is not completed yet or in lldpStatsRemTablesDeletes since the deletion would only be a partial deletion. If the failure was the result of lack of resources, the lldpStatsRemTablesDrops counter should be incremented once.
TIM lldpV2StatsRemTablesLastChangeTime	1.3.111.2.802.1.1.13.1.2.1	TimeStamp	read-only	The value of sysUpTime object (defined in IETF RFC 3418) at the time an entry is created, modified, or deleted in the in tables associated with the lldpV2RemoteSystemsData objects and all LLDP extension objects associated with remote systems. An NMS can use this object to reduce polling of the lldpV2RemoteSystemsData objects.
NUM lldpV2StatsRxDestIfIndex	1.3.111.2.802.1.1.13.1.2.7.1.1	InterfaceIndex	not-accessible	The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB. The value of this object is used as an index to the lldpStatsRxPortV2Table.
ADR lldpV2StatsRxDestMACAddress	1.3.111.2.802.1.1.13.1.2.7.1.2	LldpV2DestAddressTableIndex	not-accessible	The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the lldpStatsRxPortV2Table.
lldpV2StatsRxGroup	1.3.111.2.802.1.1.13.2.2.4			The collection of objects that are used to represent LLDP reception statistics.
NUM lldpV2StatsRxPortAgeoutsTotal	1.3.111.2.802.1.1.13.1.2.7.1.8	ZeroBasedCounter32	read-only	The counter that represents the number of age-outs that occurred on a given port. An age-out is the number of times the complete set of information advertised by a particular MSAP has been deleted from tables contained in lldpV2RemoteSystemsData and lldpV2Extensions objects because the information timeliness interval has expired. This counter is similar to lldpV2StatsRemTablesAgeouts, except that the counter is on a per port basis. This enables NMS to poll tables associated with the lldpV2RemoteSystemsData objects and all LLDP extension objects associated with remote systems on the indicated port only. This counter is set to zero during agent initialization and its value should not be saved in non-volatile storage. This counter is incremented only once when the complete set of information is invalidated (aged out) from all related tables on a particular port. Partial ageing is not allowed.
lldpV2StatsRxPortEntry	1.3.111.2.802.1.1.13.1.2.7.1		not-accessible	LLDP frame reception statistics for a particular port. The port is contained in the same chassis as the LLDP agent. All counter values in a particular entry shall be maintained on a continuing basis and shall not be deleted upon expiration of rxInfoTTL timing counters in the LLDP remote systems MIB of the receipt of a shutdown frame from a remote LLDP agent. All statistical counters associated with a particular port on the local LLDP agent become frozen whenever the adminStatus is disabled for the same port. Rows in this table can only be created for MAC addresses that can validly be used in association with the type of interface concerned, as defined by Table 7-2. The contents of this table is persistent across re-initializations or re-boots.
C32 lldpV2StatsRxPortFramesDiscardedTotal	1.3.111.2.802.1.1.13.1.2.7.1.3	Counter32	read-only	The number of LLDP frames received by this LLDP agent on the indicated port, and then discarded for any reason. This counter can provide an indication that LLDP header formatting problems may exist with the local LLDP agent in the sending system or that LLDPDU validation problems may exist with the local LLDP agent in the receiving system.
C32 lldpV2StatsRxPortFramesErrors	1.3.111.2.802.1.1.13.1.2.7.1.4	Counter32	read-only	The number of invalid LLDP frames received by this LLDP agent on the indicated port, while this LLDP agent is enabled.
C32 lldpV2StatsRxPortFramesTotal	1.3.111.2.802.1.1.13.1.2.7.1.5	Counter32	read-only	The number of valid LLDP frames received by this LLDP agent on the indicated port, while this LLDP agent is enabled.
lldpV2StatsRxPortTable	1.3.111.2.802.1.1.13.1.2.7		not-accessible	A table containing LLDP reception statistics for individual ports and destination MAC addresses. Entries are not required to exist in this table while the lldpPortConfigEntry object is equal to 'disabled(4)'.
C32 lldpV2StatsRxPortTLVsDiscardedTotal	1.3.111.2.802.1.1.13.1.2.7.1.6	Counter32	read-only	The number of LLDP TLVs discarded for any reason by this LLDP agent on the indicated port.
C32 lldpV2StatsRxPortTLVsUnrecognizedTotal	1.3.111.2.802.1.1.13.1.2.7.1.7	Counter32	read-only	The number of LLDP TLVs received on the given port that are not recognized by this LLDP agent on the indicated port. An unrecognized TLV is referred to as the TLV whose type value is in the range of reserved TLV types (000 1001 - 111 1110) in Table 8-1 of IEEE Std 802.1AB-2015. An unrecognized TLV may be a basic management TLV from a later LLDP version.
ADR lldpV2StatsTxDestMACAddress	1.3.111.2.802.1.1.13.1.2.6.1.2	LldpV2DestAddressTableIndex	not-accessible	The index value used to identify the destination MAC address associated with this entry. Its value identifies the row in the lldpV2DestAddressTable where the MAC address can be found. The value of this object is used as an index to the lldpV2StatsTxPortTable.
lldpV2StatsTxGroup	1.3.111.2.802.1.1.13.2.2.5			The collection of objects that are used to represent LLDP transmission statistics.
NUM lldpV2StatsTxIfIndex	1.3.111.2.802.1.1.13.1.2.6.1.1	InterfaceIndex	not-accessible	The interface index value used to identify the port associated with this entry. Its value is an index into the interfaces MIB. The value of this object is used as an index to the lldpV2StatsTxPortTable.
C32 lldpV2StatsTxLLDPDULengthErrors	1.3.111.2.802.1.1.13.1.2.6.1.4	Counter32	read-only	The number of LLDPDU Length Errors recorded for the Port.
lldpV2StatsTxPortEntry	1.3.111.2.802.1.1.13.1.2.6.1		not-accessible	LLDP frame transmission statistics for a particular port and destination MAC address. The port is contained in the same chassis as the LLDP agent. All counter values in a particular entry shall be maintained on a continuing basis and shall not be deleted upon expiration of rxInfoTTL timing counters in the LLDP remote systems MIB of the receipt of a shutdown frame from a remote LLDP agent. All statistical counters associated with a particular port on the local LLDP agent become frozen whenever the adminStatus is disabled for the same port. Rows in this table can only be created for MAC addresses that can validly be used in association with the type of interface concerned, as defined by Table 7-2.
C32 lldpV2StatsTxPortFramesTotal	1.3.111.2.802.1.1.13.1.2.6.1.3	Counter32	read-only	The number of LLDP frames transmitted by this LLDP agent on the indicated port to the destination MAC address associated with this row of the table.
lldpV2StatsTxPortTable	1.3.111.2.802.1.1.13.1.2.6		not-accessible	A table containing LLDP transmission statistics for individual port/destination address combinations. Entries are not required to exist in this table while the lldpPortConfigEntry object is equal to 'disabled(4)'.
lldpV2TxCompliance	1.3.111.2.802.1.1.13.2.1.2			A compliance statement for SNMP entities that implement the LLDP MIB and have the capability of transmitting LLDP frames. This version defines compliance requirements for V2 of the LLDP MIB module.
U32 lldpV2TxCreditMax	1.3.111.2.802.1.1.13.1.1.5	Unsigned32	read-write	The maximum number of consecutive LLDPDUs that can be transmitted at any time. The default value for lldpV2TxCreditMax object is 5 PDUs. The value of this object is used as the initial value of the lldpV2PortTxCreditMax object on row creation in the lldpV2PortConfigTableV2. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
U32 lldpV2TxFastInit	1.3.111.2.802.1.1.13.1.1.7	Unsigned32	read-write	The initial value used to initialize the txFast variable which determines the number of transmissions that are made in fast transmission mode. The default value for lldpV2TxFastInit object is 4. The value of this object is used as the initial value of the lldpV2PortTxFastInit object on row creation in the lldpV2PortConfigTableV2. The value of this object is restored from non-volatile storage after a re-initialization of the management system.
lldpV2TxRxCompliance	1.3.111.2.802.1.1.13.2.1.1			A compliance statement for all SNMP entities that implement the LLDP MIB as either a transmitter or a receiver of LLDPDUs. This version defines compliance requirements for V2 of the LLDP MIB module.

FAQ

How does LLDP-V2-MIB help detect an unexpected new device plugged into a switch port?
Through its remote (neighbor) system data tables, it maintains a live list of directly connected LLDP neighbors per port; an NMS comparing this against expected topology can flag an unexpected new neighbor, a missing expected neighbor, or a topology change via notification, indicating a mis-cabled or newly connected device.

What configuration objects does LLDP-V2-MIB expose per port?
It exposes LLDP admin status, transmit interval, hold multiplier, reinitialization delay, notification interval, and fast-transmit parameters per port, letting an operator confirm LLDP is enabled and correctly timed before relying on its neighbor data for topology discovery.

RFC description

Defines managed objects for Link Layer Discovery Protocol Version 2 (LLDPv2) configuration, statistics, and neighbor system information as standardized in IEEE 802.1AB-2016.

Start monitoring Vendor-neutral IEEE 802.1AB-2016 standard (any LLDP-capable switch/router/endpoint) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download LLDP-V2-MIB

What Is LLDP-V2-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

FAQ

RFC description