LIEBERT-UPSTATION-GXT-UPS-MIB

All MIBs › LIEBERT-UPSTATION-GXT-UPS-MIB

Category: Domain: Power/UPS, Vendor: Liebert

Description: SNMP objects for the Liebert UPStation GXT UPS line, covering management of AC input, output, and battery.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is LIEBERT-UPSTATION-GXT-UPS-MIB?

LIEBERT-UPSTATION-GXT-UPS-MIB is a Liebert vendor MIB defining SNMP objects for the Liebert UPStation GXT uninterruptible power supply product line, covering AC input, output, and battery management. It exposes data across the classic UPS monitoring categories: input line voltage/frequency, output load and voltage, and battery charge/runtime status. This MIB is squarely a hardware status monitoring MIB, used to track power supply health including battery charge level, estimated runtime remaining, input power quality, and output load, all critical for detecting an impending power failure or battery degradation. It likely parallels or complements the standard UPS-MIB (RFC 1628) object structure given its input/output/battery organization, though no explicit import was confirmed. It is typically deployed in data centers and server rooms to remotely monitor UPS health and trigger alerts before battery depletion or utility power loss causes an outage. Engineers can download the LIEBERT-UPSTATION-GXT-UPS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in LIEBERT-UPSTATION-GXT-UPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Liebert UPStation GXT uninterruptible power supply (UPS)

Monitoring Examples

An administrator would poll battery-related objects to check remaining battery charge percentage and estimated runtime, detecting a degrading battery before it can no longer support a graceful shutdown during a power outage. AC input voltage/frequency objects would be monitored to detect utility power sag or brownout conditions, while output load objects reveal whether the UPS is nearing its capacity limit. No specific sample object names were provided in the source data, so exact table/column names cannot be cited with confidence.

What Can Be Monitored

battery charge level
estimated battery runtime
AC input voltage and frequency
output load
UPS operational status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
TimeTicks
enterprises

From RFC1213-MIB

DisplayString
sysUpTime

OIDs

OID symbolic	OID numeric	Type	Access	Description
emerson	1.3.6.1.4.1.476
lcUpsAlarm	1.3.6.1.4.1.476.1.1.1.1.6
lcUpsAlarmBatteryBad	1.3.6.1.4.1.476.1.1.1.1.6.3.9
lcUpsAlarmConditions	1.3.6.1.4.1.476.1.1.1.1.6.3
OID lcUpsAlarmDescr	1.3.6.1.4.1.476.1.1.1.1.6.2.1.2	OBJECT IDENTIFIER	read-only	A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.
lcUpsAlarmEntry	1.3.6.1.4.1.476.1.1.1.1.6.2.1		not-accessible
INT lcUpsAlarmId	1.3.6.1.4.1.476.1.1.1.1.6.2.1.1	INTEGER	read-only	A unique identifier for an alarm condition. This value must remain constant between agent initializations.
lcUpsAlarmInputFreqError	1.3.6.1.4.1.476.1.1.1.1.6.3.13
lcUpsAlarmInputOverVoltage	1.3.6.1.4.1.476.1.1.1.1.6.3.8
lcUpsAlarmLowBatteryShutdown	1.3.6.1.4.1.476.1.1.1.1.6.3.2
lcUpsAlarmLowBatteryWarning	1.3.6.1.4.1.476.1.1.1.1.6.3.1
lcUpsAlarmOnBattery	1.3.6.1.4.1.476.1.1.1.1.6.3.10
lcUpsAlarmOutputOverloadShutdown	1.3.6.1.4.1.476.1.1.1.1.6.3.7
lcUpsAlarmOutputOverloadWarning	1.3.6.1.4.1.476.1.1.1.1.6.3.6
lcUpsAlarmOutputOverVoltage	1.3.6.1.4.1.476.1.1.1.1.6.3.16
lcUpsAlarmOutputUnderVoltage	1.3.6.1.4.1.476.1.1.1.1.6.3.15
lcUpsAlarmOverTempShutdown	1.3.6.1.4.1.476.1.1.1.1.6.3.5
lcUpsAlarmOverTempWarning	1.3.6.1.4.1.476.1.1.1.1.6.3.4
GAU lcUpsAlarms	1.3.6.1.4.1.476.1.1.1.1.6.1	Gauge	read-only	The current number of alarm conditions.
lcUpsAlarmStopNoticeIssued	1.3.6.1.4.1.476.1.1.1.1.6.3.11
lcUpsAlarmTable	1.3.6.1.4.1.476.1.1.1.1.6.2		not-accessible
TIK lcUpsAlarmTime	1.3.6.1.4.1.476.1.1.1.1.6.2.1.3	TimeTicks	read-only	The value of sysUpTime when the alarm condition occured.
NTF lcUpsAlarmTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.11			An Alarm condition has occurred and is being reported in the lcUpsAlarmTable.
lcUpsAlarmUpsOff	1.3.6.1.4.1.476.1.1.1.1.6.3.12
lcUpsAlarmUtilFailed	1.3.6.1.4.1.476.1.1.1.1.6.3.3
lcUpsBadBypassPower	1.3.6.1.4.1.476.1.1.1.1.6.3.17
INT lcUpsBatCapacity	1.3.6.1.4.1.476.1.1.1.1.2.6	INTEGER	read-only	The current battery capacity in percentage of total available.
lcUpsBattery	1.3.6.1.4.1.476.1.1.1.1.2
INT lcUpsBatTimeRemaining	1.3.6.1.4.1.476.1.1.1.1.2.1	INTEGER	read-only	The estimated time to depletion of battery charge. (Unit of measure: Minute)
INT lcUpsBatVoltage	1.3.6.1.4.1.476.1.1.1.1.2.3	INTEGER	read-only	The current battery voltage. (Unit of measure: volt)
lcUpsBypass	1.3.6.1.4.1.476.1.1.1.1.13
lcUpsBypassEntry	1.3.6.1.4.1.476.1.1.1.1.13.4.1		not-accessible
INT lcUpsBypassFrequency	1.3.6.1.4.1.476.1.1.1.1.13.2	INTEGER	read-only	The current bypass frequency. (Unit of measure: Hertz)
INT lcUpsBypassLine	1.3.6.1.4.1.476.1.1.1.1.13.4.1.1	INTEGER	read-only	The bypass Line.
INT lcUpsBypassNumLines	1.3.6.1.4.1.476.1.1.1.1.13.3	INTEGER	read-only	The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.
lcUpsBypassTable	1.3.6.1.4.1.476.1.1.1.1.13.4		not-accessible
INT lcUpsBypassVoltage	1.3.6.1.4.1.476.1.1.1.1.13.4.1.2	INTEGER	read-only	The bypass voltage. (Unit of measure: Volt)
lcUpsConfig	1.3.6.1.4.1.476.1.1.1.1.14
INT lcUpsConfigAudibleStatus	1.3.6.1.4.1.476.1.1.1.1.14.5	INTEGER	read-write	The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm.
INT lcUpsConfigAutoRestart	1.3.6.1.4.1.476.1.1.1.1.14.7	INTEGER	read-write	Setting this object will start the output after the indicated number of ticks (1 tick = 10 seconds), including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will disable autorestart.
INT lcUpsConfigBypassInstalled	1.3.6.1.4.1.476.1.1.1.1.14.2	INTEGER	read-only	Indicates if a bypass is installed in the UPS.
INT lcUpsConfigLowBattTime	1.3.6.1.4.1.476.1.1.1.1.14.6	INTEGER	read-write	The value of lcUpsBatTimeRemaining at which a lowBatteryWarning condition is declared. (Unit of measure: Minute)
INT lcUpsConfigModuleCount	1.3.6.1.4.1.476.1.1.1.1.14.3	INTEGER	read-only	A number identifying how many multi-module UPS are connected to the System Control Cabinet.
INT lcUpsConfigType	1.3.6.1.4.1.476.1.1.1.1.14.1	INTEGER	read-only	Indicates the UPS topology.
lcUpsControl	1.3.6.1.4.1.476.1.1.1.1.8
INT lcUpsControlCancelCommands	1.3.6.1.4.1.476.1.1.1.1.8.7	INTEGER	read-write	Setting this variable to 'cancel' will cause the agent to issue instructions to the UPS to cancel all outstanding commands, such as lcUpsControlOutputOff, lcUpsControlOutputOn, lcUpsControlUnixShutdown.
INT lcUpsControlOutputOffDelay	1.3.6.1.4.1.476.1.1.1.1.8.1	INTEGER	read-write	Setting this object causes the agent to instruct the UPS to turn off the output after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsOutputOffTrap when the countdown finishes. Note that different models have different clock resolutions, usually greater than 1 second. As a result, the command will only be accurate to the resolution of the UPS's clock. The command can be cancelled by setting lcUpsControlCancelCommand to the value cancel.
INT lcUpsControlOutputOffTrapDelay	1.3.6.1.4.1.476.1.1.1.1.8.3	INTEGER	read-write	When 'lcUpsControlOutputOffDelay' reaches a value less than or equal to this object's value, an lcUpsOutputOffWarningTrap will be produced and this object will be reset to 0.
INT lcUpsControlOutputOnDelay	1.3.6.1.4.1.476.1.1.1.1.8.2	INTEGER	read-write	Setting this object causes the agent to instruct the UPS to turn on the output after the indicated number of seconds. The agent counts down the number of seconds until the event will take place. The agent issues an lcUpsOutputOnTrap when the countdown finishes. Note that different models have different clock resolutions, usually greater than 1 second. As a result, the command will only be accurate to the resolution of the UPS's clock. The command can be cancelled by setting lcUpsControlCancelCommand to the value cancel.
INT lcUpsControlOutputOnTrapDelay	1.3.6.1.4.1.476.1.1.1.1.8.4	INTEGER	read-write	When 'lcUpsControlOutputOnDelay' reaches a value less than or equal to this object's value, an lcUpsOutputOnWarningTrap will be produced and this object will be reset to 0.
INT lcUpsControlRebootAgentDelay	1.3.6.1.4.1.476.1.1.1.1.8.8	INTEGER	read-write	Setting this object causes the agent to reboot after the indicated number of seconds have expired. The value will count down until the event takes place. The command can be cancelled by setting lcUpsControlCancleCommand to the value cancel.
INT lcUpsControlUnixShutdownDelay	1.3.6.1.4.1.476.1.1.1.1.8.5	INTEGER	read-write	Setting this object causes the agent to instruct the UPS to perform a UNIX Shutdown in the indicated number of seconds. The agent counts down the number of seconds until the event will take place. A Unix shutdown is only valid if the UPS is on Battery. During a UNIX Shutdown, the UPS will turn off the output even if the Utility comes back on line before the shutdown time arrives. Note that different models have different clock resolutions, usually greater than 1 second. As a result, the command will only be accurate to the resolution of the UPS's clock. The command can be cancelled by setting lcUpsControlCancelCommand to the value 'cancel'.
INT lcUpsControlUnixShutdownTrapDelay	1.3.6.1.4.1.476.1.1.1.1.8.6	INTEGER	read-write	When 'lcUpsControlUnixShutdownDelay' reaches a value less than or equal to this object's value, an lcUpsUnixShutdownWarningTrap will be produced and this object will be reset to 0.
lcUpsIdent	1.3.6.1.4.1.476.1.1.1.1.1
STR lcUpsIdentFirmwareVersion	1.3.6.1.4.1.476.1.1.1.1.1.5	DisplayString	read-only	The firmware revision level of the UPS.
STR lcUpsIdentManufactureDate	1.3.6.1.4.1.476.1.1.1.1.1.7	DisplayString	read-only	The date of manufacture of the UPS.
STR lcUpsIdentManufacturer	1.3.6.1.4.1.476.1.1.1.1.1.1	DisplayString	read-only	The UPS manufacturer.
STR lcUpsIdentModel	1.3.6.1.4.1.476.1.1.1.1.1.2	DisplayString	read-write	The UPS Model designation.
STR lcUpsIdentSerialNumber	1.3.6.1.4.1.476.1.1.1.1.1.6	DisplayString	read-only	The serial number of the UPS.
STR lcUpsIdentSoftwareVersion	1.3.6.1.4.1.476.1.1.1.1.1.3	DisplayString	read-only	The UPS SNMP Agent software version.
OID lcUpsIdentSpecific	1.3.6.1.4.1.476.1.1.1.1.1.4	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular UPS being managed. This object is used to locate the product-specific MIB for this device. If this information is not present, its value should be the OBJECT IDENTIFIER { 0 0 }, which is a syntactically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.
lcUpsInput	1.3.6.1.4.1.476.1.1.1.1.3
lcUpsInputEntry	1.3.6.1.4.1.476.1.1.1.1.3.6.1		not-accessible
NTF lcUpsInputFreqErrorTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.22			An ldUpsInputFreqErrorTrap signifies that the UPS has detected that input frequency is outside tolerable variance.
INT lcUpsInputFrequency	1.3.6.1.4.1.476.1.1.1.1.3.1	INTEGER	read-only	The current input frequency. (Unit of measure: Hertz)
INT lcUpsInputLine	1.3.6.1.4.1.476.1.1.1.1.3.6.1.1	INTEGER	read-only	The input Line.
INT lcUpsInputNumLines	1.3.6.1.4.1.476.1.1.1.1.3.5	INTEGER	read-only	The number of input lines utilized in this device. This entry indicates the number of rows in the input table.
NTF lcUpsInputOverVoltageTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.8			An lcUpsInputOverVoltageTrap signifies that the UPS has detected a high input voltage condition.
lcUpsInputTable	1.3.6.1.4.1.476.1.1.1.1.3.6		not-accessible
INT lcUpsInputVoltage	1.3.6.1.4.1.476.1.1.1.1.3.6.1.2	INTEGER	read-only	The input voltage. (Unit of measure: Volt)
lcUpsInverter	1.3.6.1.4.1.476.1.1.1.1.5
INT lcUpsInverterStatus	1.3.6.1.4.1.476.1.1.1.1.5.1	INTEGER	read-only	The state of the inverter. Unknown is returned if the state can not be determined.
NTF lcUpsLowBatteryShutdownTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.5			An lcUpsLowBatteryShutdownTrap signifies that the UPS has shut off the output due to a Low Battery state.
NTF lcUpsLowBatteryWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.4			An lcUpsLowBatteryWarningTrap signifies that the UPS has entered a Low Battery state.
lcUpsNominal	1.3.6.1.4.1.476.1.1.1.1.9
INT lcUpsNominalInputFreq	1.3.6.1.4.1.476.1.1.1.1.9.6	INTEGER	read-write	The nominal input frequency. (Unit of measure: Hertz)
INT lcUpsNominalInputVoltage	1.3.6.1.4.1.476.1.1.1.1.9.2	INTEGER	read-write	The nominal input voltage. (Unit of measure: volt)
INT lcUpsNominalOutputFreq	1.3.6.1.4.1.476.1.1.1.1.9.5	INTEGER	read-write	The nominal output frequency. (Unit of measure: Hertz)
INT lcUpsNominalOutputVaRating	1.3.6.1.4.1.476.1.1.1.1.9.7	INTEGER	read-write	The nominal Volt-Amp rating.
INT lcUpsNominalOutputVoltage	1.3.6.1.4.1.476.1.1.1.1.9.1	INTEGER	read-write	The nominal output voltage. (Unit of measure: volt)
INT lcUpsNominalOutputWattsRating	1.3.6.1.4.1.476.1.1.1.1.9.8	INTEGER	read-write	The nominal power rating. (Unit of measure: watt)
NTF lcUpsOnBatteryTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.3			An lcUpsOnBatteryTrap signifies that the UPS is currently on Battery Power.
INT lcUpsOnBypass	1.3.6.1.4.1.476.1.1.1.1.13.1	INTEGER	read-only	Indicates that the UPS is currently on bypass.
lcUpsOutput	1.3.6.1.4.1.476.1.1.1.1.4
INT lcUpsOutputCurrent	1.3.6.1.4.1.476.1.1.1.1.4.4.1.3	INTEGER	read-only	The output current. (Unit of measure: Amp)
lcUpsOutputEntry	1.3.6.1.4.1.476.1.1.1.1.4.4.1		not-accessible
INT lcUpsOutputFrequency	1.3.6.1.4.1.476.1.1.1.1.4.1	INTEGER	read-only	The current output frequency. (Unit of measure: Hertz)
INT lcUpsOutputLine	1.3.6.1.4.1.476.1.1.1.1.4.4.1.1	INTEGER	read-only	The output Line.
INT lcUpsOutputLoad	1.3.6.1.4.1.476.1.1.1.1.4.2	INTEGER	read-only	The current output load percentage.
INT lcUpsOutputNumLines	1.3.6.1.4.1.476.1.1.1.1.4.3	INTEGER	read-only	The number of output lines utilized in this device. This entry indicates the number of rows in the output table.
NTF lcUpsOutputOffTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.12			An lcUpsOutputOffTrap is sent when the UPS turns all of its output off, either at the inverter or via a relay.
NTF lcUpsOutputOffWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.13			An lcUpsOutputOffWarningTrap is sent when the lcUpsControlOutputOffDelay reaches the value of lcUpsControlOutputOffTrapDelay.
NTF lcUpsOutputOnTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.14			An lcUpsOutputOnTrap is sent when the UPS turns all of its output back on, either at the inverter or via a relay.
NTF lcUpsOutputOnWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.15			An lcUpsOutputOnWarningTrap is sent when the lcUpsControlOutputOnDelay reaches the value of lcUpsControlOutputOnTrapDelay.
NTF lcUpsOutputOverVoltageTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.24			An lcUpsOutputOverVoltageTrap signifies that the UPS has detected that the output voltage is too high.
lcUpsOutputTable	1.3.6.1.4.1.476.1.1.1.1.4.4		not-accessible
INT lcUpsOutputVoltage	1.3.6.1.4.1.476.1.1.1.1.4.4.1.2	INTEGER	read-only	The output voltage. (Unit of measure: Volt)
INT lcUpsOutputWatts	1.3.6.1.4.1.476.1.1.1.1.4.5	INTEGER	read-only	The output power in watts.
NTF lcUpsOverloadShutdownTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.2			An lcUpsOverloadShutdownTrap signifies that the UPS has detected an Overload condition where the output load has exceeded the UPS's rated capacity and has shut off the output.
NTF lcUpsOverloadWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.1			An lcUpsOverloadWarningTrap signifies that the UPS has detected an Overload condition where the output load has exceeded the UPS's rated capacity.
NTF lcUpsOverTempShutdownTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.10			An lcUpsOverTempShutdownTrap signifies that the UPS has detected a excessive temperature condition and shut off the output.
NTF lcUpsOverTempWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.9			An lcUpsOverTempWarningTrap signifies that the UPS has detected a excessive temperature condition.
lcUpsTest	1.3.6.1.4.1.476.1.1.1.1.7
INT lcUpsTestBattery	1.3.6.1.4.1.476.1.1.1.1.7.1	INTEGER	read-write	Setting this variable to 'start' will initiate the battery test. Setting this variable to 'abort' will stop the battery test if the test is in- progress, otherwise it has no effect. Setting this variable to 'unknown' has no effect. Reading this variable will always result in a return value of 'unknown'. If 'lcUpsTestBatteryStatus' is 'failed' the test may not be performed again and the status will remain in the failure state.
INT lcUpsTestBatteryStatus	1.3.6.1.4.1.476.1.1.1.1.7.2	INTEGER	read-only	The status of the battery test.
lcUpsTraps	1.3.6.1.4.1.476.1.1.1.1.11
NTF lcUpsUnixShutdownTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.16			An lcUpsUnixShutodwnTrap is sent 2 seconds before the UPS is scheduled to perform a Unix Shutdown.
NTF lcUpsUnixShutdownWarningTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.17			An lcUpsUnixShutdownWarningTrap is sent when the lcUpsControlUnixShudownDelay reaches the value of lcUpsControlUnixShutdownTrapDelay.
NTF lcUpsUtilPowerFailedTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.6			An lcUpsUtilPowerFailedTrap signifies that the utility power input to the UPS has been lost.
NTF lcUpsUtilPowerRestoredTrap	1.3.6.1.4.1.476.1.1.1.1.11.0.7			An lcUpsUtilPowerRestoredTrap signifies that the utility power has been restored to the UPS.
liebertCorp	1.3.6.1.4.1.476.1
liebertUps	1.3.6.1.4.1.476.1.1
luCore	1.3.6.1.4.1.476.1.1.1.1
luExperimental	1.3.6.1.4.1.476.1.1.2
luExtensions	1.3.6.1.4.1.476.1.1.1
luPrivate	1.3.6.1.4.1.476.1.1.3
luUPStationGxt	1.3.6.1.4.1.476.1.1.1.14

RFC description

Defines SNMP objects for the Liebert UPStation GXT UPS product line covering AC input, output, and battery management.

Start monitoring Liebert UPStation GXT uninterruptible power supply with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download LIEBERT-UPSTATION-GXT-UPS-MIB

What Is LIEBERT-UPSTATION-GXT-UPS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description