LBHUB-ECS-MIB

All MIBs › LBHUB-ECS-MIB

Category: Network Management

Description: Manages the Enterprise Control Software module on LANBuilder network hubs.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is LBHUB-ECS-MIB?

This MIB manages the Enterprise Control Software (ECS) module on 3Com LANBuilder network hubs, an older enterprise hub/switch management platform. Given its minimal available metadata, it broadly covers generic application-level management objects and trap definitions for the hub's control software layer, likely including basic status and notification objects for the ECS module. In a monitoring context it would be used to check hardware/software operational status of the hub's control module and to receive generic traps signaling state changes or faults, though detailed counters are not evident from available naming. It falls under the 3Com enterprise MIB tree and follows standard SNMPv1/v2 enterprise MIB conventions. It would be deployed in legacy 3Com LANBuilder hub installations, an older class of enterprise networking hardware largely superseded by modern switches. Engineers can download the LBHUB-ECS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in LBHUB-ECS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

3Com LANBuilder network hubs

Monitoring Examples

An administrator managing a 3Com LANBuilder hub would monitor the ECS module's status objects and subscribe to genericTrap notifications to detect state changes in the hub's control software. Given the limited sample objects (viewBuilderApps, genericTrap), monitoring would focus on confirming the ECS application is running and alerting on generic fault traps rather than granular performance counters. This MIB would mainly serve legacy-equipment fault detection in older 3Com hub deployments.

What Can Be Monitored

ECS module operational status
generic trap notifications
hub control software application state

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
NetworkAddress
TimeTicks
enterprises
mgmt

From RFC1213-MIB

DisplayString
PhysAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
mib_2	1.3.6.1.2.1
system	1.3.6.1.2.1.1
interfaces	1.3.6.1.2.1.2
at	1.3.6.1.2.1.3
ip	1.3.6.1.2.1.4
icmp	1.3.6.1.2.1.5
tcp	1.3.6.1.2.1.6
udp	1.3.6.1.2.1.7
egp	1.3.6.1.2.1.8
transmission	1.3.6.1.2.1.10
snmp	1.3.6.1.2.1.11
a3Com	1.3.6.1.4.1.43
products	1.3.6.1.4.1.43.1
terminalServer	1.3.6.1.4.1.43.1.1
dedicatedBridgeServer	1.3.6.1.4.1.43.1.2
dedicatedRouteServer	1.3.6.1.4.1.43.1.3
brouter	1.3.6.1.4.1.43.1.4
genericMSWorkstation	1.3.6.1.4.1.43.1.5
genericMSServer	1.3.6.1.4.1.43.1.6
genericUnixServer	1.3.6.1.4.1.43.1.7
hub	1.3.6.1.4.1.43.1.8
linkBuilder3GH	1.3.6.1.4.1.43.1.8.1
linkBuilder10BTi	1.3.6.1.4.1.43.1.8.2
linkBuilderECS	1.3.6.1.4.1.43.1.8.3
NTF powerSupplyFailure	1.3.6.1.4.1.43.1.8.3.0.0			One of the PSUs has failed, the value of ecsPSUStatus is returned to indicate which PSU has failed.
NTF fanFailure	1.3.6.1.4.1.43.1.8.3.0.1			A LinkBuilder ECS Fan has failed, requiring immediate attenstion.
NTF configurationChanged	1.3.6.1.4.1.43.1.8.3.0.2			The LinkBuilder ECS configuartion has changed. Either a card has been added or removed, a port disabled or enabled from the front panel or a AUI port has been selected/deselected.
NTF portTrap	1.3.6.1.4.1.43.1.8.3.0.3			A port has partitioned/unpartitioned or has changed link state. The values of ecsInfoSlotIndex and ecsInfoPortIndex are returned to indicate the slot and port, the ecsPortErrorState is returned to indicate the type or port error.
NTF resilientLinkTrap	1.3.6.1.4.1.43.1.8.3.0.4			The LinkBuilder ECS Resilient Link system has operated. The resilient link is returned to determine the action taken.
NTF rateTrap	1.3.6.1.4.1.43.1.8.3.0.5			A Guage threshold has been exceeded. The slot and port number are given by the vakues if ecsInfoSlotIndex and ecsInfoPortIndex and the guage that has been exceeded is given by the value of ecsPortErrorState.
NTF stationlocateTrap	1.3.6.1.4.1.43.1.8.3.0.6			The Station Locate databse has either changed or has become full. The particular condition is shown by the value of ecsRLCSLDataBAseStatus returned.
NTF secureRLCTrap	1.3.6.1.4.1.43.1.8.3.0.7			There has been access to the security menus from the front panel menus. The value of ecsAgentSecureManagementStatus reports whether the trap was generated beacuse the security menus were entered, the secure password was violated or the security configuration has been changed.
NTF secureRLCportTrap	1.3.6.1.4.1.43.1.8.3.0.8			A secure port has either detected an authorised port and taken appropriate action or has learnt an authorised station on the slot and port indicated.
linkBuilderMSH	1.3.6.1.4.1.43.1.8.4
linkBuilderFMS	1.3.6.1.4.1.43.1.8.5
linkBuilderFMSII	1.3.6.1.4.1.43.1.8.7
linkBuilderFMSLBridge	1.3.6.1.4.1.43.1.8.10
cards	1.3.6.1.4.1.43.1.9
linkBuilder3GH_cards	1.3.6.1.4.1.43.1.9.1
linkBuilder10BTi_cards	1.3.6.1.4.1.43.1.9.2
linkBuilder10BTi_cards_utp	1.3.6.1.4.1.43.1.9.2.1
linkBuilder10BT_cards_utp	1.3.6.1.4.1.43.1.9.2.2
linkBuilderECS_cards	1.3.6.1.4.1.43.1.9.3
linkBuilderMSH_cards	1.3.6.1.4.1.43.1.9.4
linkBuilderFMS_cards	1.3.6.1.4.1.43.1.9.5
linkBuilderFMS_cards_utp	1.3.6.1.4.1.43.1.9.5.1
linkBuilderFMS_cards_coax	1.3.6.1.4.1.43.1.9.5.2
linkBuilderFMS_cards_fiber	1.3.6.1.4.1.43.1.9.5.3
linkBuilderFMS_cards_12fiber	1.3.6.1.4.1.43.1.9.5.4
linkBuilderFMS_cards_24utp	1.3.6.1.4.1.43.1.9.5.5
linkBuilderFMSII_cards	1.3.6.1.4.1.43.1.9.6
linkBuilderFMSII_cards_12tp_rj45	1.3.6.1.4.1.43.1.9.6.1
linkBuilderFMSII_cards_10coax_bnc	1.3.6.1.4.1.43.1.9.6.2
linkBuilderFMSII_cards_6fiber_st	1.3.6.1.4.1.43.1.9.6.3
linkBuilderFMSII_cards_12fiber_st	1.3.6.1.4.1.43.1.9.6.4
linkBuilderFMSII_cards_24tp_rj45	1.3.6.1.4.1.43.1.9.6.5
linkBuilderFMSII_cards_24tp_telco	1.3.6.1.4.1.43.1.9.6.6
amp_mib	1.3.6.1.4.1.43.3
genericTrap	1.3.6.1.4.1.43.4
viewBuilderApps	1.3.6.1.4.1.43.5
specificTrap	1.3.6.1.4.1.43.6
linkBuilder3GH_mib	1.3.6.1.4.1.43.7
linkBuilder10BTi_mib	1.3.6.1.4.1.43.8
linkBuilderECS_mib	1.3.6.1.4.1.43.9
ecsAgent	1.3.6.1.4.1.43.9.1
ecsAgentSystemIdentifier	1.3.6.1.4.1.43.9.1.1
STR ecsManufacturerId	1.3.6.1.4.1.43.9.1.1.1	DisplayString	read-only	An atrribute to identify the manufacturer
STR ecsManufacturerProductId	1.3.6.1.4.1.43.9.1.1.2	DisplayString	read-only	An attribute to identify the product id.
STR ecsSoftwareVersionNumber	1.3.6.1.4.1.43.9.1.1.3	DisplayString	read-only	An atrribute to identify the software version.
INT ecsHardwareVersionNumber	1.3.6.1.4.1.43.9.1.1.4	INTEGER	read-only	An atrribute to identify the hardware version.
STR ecsAgentSystemName	1.3.6.1.4.1.43.9.1.2	DisplayString	read-write	This is an informational string that could be used to show the name of the ECSAgent or management agent.
STR ecsAgentSystemLocation	1.3.6.1.4.1.43.9.1.3	DisplayString	read-write	This is an informational string that could be used to show the physical location (i.e., area) of the ecsAgent or management agent.
TIK ecsAgentSystemTime	1.3.6.1.4.1.43.9.1.4	TimeTicks	read-write	A representation of the system time of the management system, taken from the epoch.
INT ecsAgentStatus	1.3.6.1.4.1.43.9.1.5	INTEGER	read-only	Indicates that the management agent is on line and operating.
INT ecsAgentAuthenticationStatus	1.3.6.1.4.1.43.9.1.6	INTEGER	read-only	Indicates whether management frames are checked against entries in the management tranmiter table.
INT ecsAgentSecureManagementStatus	1.3.6.1.4.1.43.9.1.7	INTEGER	read-only	Indicates whether the remote management of the security features of the ECS are enabled or not.
STR ecsAgentFrontPanelSetupPassword	1.3.6.1.4.1.43.9.1.11	DisplayString	read-write	The password used to gain access to the configuration features of the front panel control of the device.
STR ecsAgentFrontPanelDisplay	1.3.6.1.4.1.43.9.1.12	DisplayString	read-write	The string displayed on the front panel.
STR ecsAgentFrontPanelPassword	1.3.6.1.4.1.43.9.1.13	DisplayString	read-write	The password used to gain access to the front panel control of the device.
STR ecsAgentFrontPanelSecurePassword	1.3.6.1.4.1.43.9.1.14	DisplayString	read-write	The password used to gain access to the security features of the front panel control of the device. This attribute is not viewable until secure remote management is enabled.
INT ecsAgentFrontPanelLock	1.3.6.1.4.1.43.9.1.15	INTEGER	read-write	The station front panel status.
INT ecsAgentResetDevice	1.3.6.1.4.1.43.9.1.16	INTEGER	read-write	Network management module reset status. Writing a 2 to this object will reset the management agent.
INT ecsAgentRestart	1.3.6.1.4.1.43.9.1.18	INTEGER	read-write	Network management module restart status. Writing a 2 to his object will restart the management agent. This initializes all the counters, rereads the NVRAM data structure, and starts executing from the beginning of the code.
INT ecsAgentDefaultConfig	1.3.6.1.4.1.43.9.1.19	INTEGER	read-write	The device is returned to its factory settings.
ecsAgentManagementTable	1.3.6.1.4.1.43.9.1.20		not-accessible	This entity's management address table. (10 entries)
ecsAgentManagementEntry	1.3.6.1.4.1.43.9.1.20.1		not-accessible	A source address address and privileges of a particular management station.
IP ecsAgentManagementAddr	1.3.6.1.4.1.43.9.1.20.1.1	IpAddress	read-write	IpAddress of the management station.
INT ecsAgentManagementAccess	1.3.6.1.4.1.43.9.1.20.1.2	INTEGER	read-write	Setting this object to the value invalid(1) invalidates the corresponding entry in the ecsAgentManagementTable. That is, it effectively disassociates the address identified with the entry by removing the entry from the table.
INT ecsAgentManAccessLevel	1.3.6.1.4.1.43.9.1.20.1.3	INTEGER	read-write	The level of aceess attributed to tthis entry in the table.
ecsAgentTrapReceiverTable	1.3.6.1.4.1.43.9.1.21		not-accessible	This entity's Trap Receiver Table. (10 entries)
ecsAgentTrapReceiverEntry	1.3.6.1.4.1.43.9.1.21.1		not-accessible	A destination address and community string for a particular trap receiver.
IP ecsAgentTrapReceiverAddr	1.3.6.1.4.1.43.9.1.21.1.1	IpAddress	read-write	IpAddress for trap receiver.
INT ecsAgentTrapType	1.3.6.1.4.1.43.9.1.21.1.2	INTEGER	read-write	Setting this object to the value invalid(1) invalidates the corresponding entry in the ECSAgentTrapReceiverTable. That is, it effectively disassociates the address identified with the entry by removing the entry from the table.
STR ecsAgentTrapReceiverComm	1.3.6.1.4.1.43.9.1.21.1.3	DisplayString	read-write	Community string used for traps.
INT ecsAgentTrapLevel	1.3.6.1.4.1.43.9.1.21.1.4	INTEGER	read-only	Indicates the type of traps that will be sent to this address.
INT ecsAgentAuthTrapState	1.3.6.1.4.1.43.9.1.22	INTEGER	read-write	Enable or disable the use of authentication error trap generation.
IP ecsAgentIpAddr	1.3.6.1.4.1.43.9.1.23	IpAddress	read-write	The network management module's administrative IpAddress. The current operational IpAddress can be obtained from the ipAdEntAddr entry in the ipAddrTable.
IP ecsAgentIpNetmask	1.3.6.1.4.1.43.9.1.24	IpAddress	read-write	The network management module's administrative subnet mask. The current operational subnet mask can be obtained from the ipAdEntNetMask entry in the ipAddrTable.
IP ecsAgentDefaultGateway	1.3.6.1.4.1.43.9.1.25	IpAddress	read-write	The network management module's administrative default gateway IpAddress. The current operational default gateway's IpAddress can be obtained from the ipRoutingTable.
IP ecsAgentIpBroadAddr	1.3.6.1.4.1.43.9.1.26	IpAddress	read-write	The network management module's adminstrative default broadcast address
OCT ecsAgentMACAddress	1.3.6.1.4.1.43.9.1.27	OCTET STRING	read-only	The MAC address of the ECS Agent.
INT ecsAgentSecureTrapState	1.3.6.1.4.1.43.9.1.28	INTEGER	read-write	Enable or disable the generation of security traps.
INT ecsAgentLastSystemError	1.3.6.1.4.1.43.9.1.29	INTEGER	read-only	The error number of the last system error.
TIK ecsAgentLastTrap	1.3.6.1.4.1.43.9.1.30	TimeTicks	read-only	The time, taken from the epoch when the last trap or event would have been generated.
ecsEnvironment	1.3.6.1.4.1.43.9.2
INT ecsRackType	1.3.6.1.4.1.43.9.2.1	INTEGER	read-only	The rack type of the LinkBuilder ECS.
ecsRackConfigurationTable	1.3.6.1.4.1.43.9.2.2		not-accessible	The current configuration of the Ether Connect System rack.
ecsSlotConfigEntry	1.3.6.1.4.1.43.9.2.2.1		not-accessible	The description of the type of module in each slot.
INT ecsSlotConfigIndex	1.3.6.1.4.1.43.9.2.2.1.1	INTEGER	read-only	The device type found in a slot.
STR ecsSlotCardName	1.3.6.1.4.1.43.9.2.2.1.2	DisplayString	read-write	This is an informational string that could be used to show the name of a card.
INT ecsSlotDeviceType	1.3.6.1.4.1.43.9.2.2.1.3	INTEGER	read-only	The device type found in a slot.
STR ecsSlotSoftVerNum	1.3.6.1.4.1.43.9.2.2.1.4	DisplayString	read-only	A description of the software version number.
INT ecsSlotHardVerNum	1.3.6.1.4.1.43.9.2.2.1.5	INTEGER	read-only	Hardware version number of the card.
INT ecsSlotNumOfPorts	1.3.6.1.4.1.43.9.2.2.1.6	INTEGER	read-only	The number of repeater ports on the card.
STR ecsSlotMediaType	1.3.6.1.4.1.43.9.2.2.1.7	DisplayString	read-only	The media type associated with this slot can take on the following values: No port, AUI, Cheapernet, FOIRL, UTP, STP, FOASTAR, Through air, Plastic Fibre.
INT ecsCardReset	1.3.6.1.4.1.43.9.2.2.1.8	INTEGER	read-write	The hardware for specified repeater line card is reset.
INT ecsLampOverRide	1.3.6.1.4.1.43.9.2.2.1.9	INTEGER	read-write	The lamps on the specified repeater line card are forced on for normal operation.
INT ecsCardIsolated	1.3.6.1.4.1.43.9.2.2.1.10	INTEGER	read-write	The LinkBuilder ECS card is isolated from the chassis backplane.
IP ecsCardIpAddress	1.3.6.1.4.1.43.9.2.2.1.11	IpAddress	read-only	For some devices the LinkBuilder ECS may be able to determine the IP address of a intelligent card that is in the slot. If the value returned is 0.0.0.0 then this indicates that the address can not be determined.
INT ecsPSUStatus	1.3.6.1.4.1.43.9.2.3	INTEGER	read-only	The status of the PSUs in the LinkBuilder ECS.
INT ecsFanStatus	1.3.6.1.4.1.43.9.2.4	INTEGER	read-only	The status of the fans in the LinkBuilder ECS.
ecsRLCResilientLinks	1.3.6.1.4.1.43.9.3
INT ecsRLCNumberOfResilientLinks	1.3.6.1.4.1.43.9.3.1	INTEGER	read-only	The number of resilient links currently configured on the LinkBuilder ECS.
INT ecsRLCNumberOfDOBPorts	1.3.6.1.4.1.43.9.3.2	INTEGER	read-only	The total number of ports that are disabled on boot, making them suitable for use with resilient links.
ecsRLCResilientLinkTable	1.3.6.1.4.1.43.9.3.3		not-accessible
ecsRLCResilientLinkEntry	1.3.6.1.4.1.43.9.3.3.1		not-accessible
INT ecsRLMainLinkSlot	1.3.6.1.4.1.43.9.3.3.1.1	INTEGER	read-write	The Slot Number for the main link of this resilient link.
INT ecsRLMainLinkPort	1.3.6.1.4.1.43.9.3.3.1.2	INTEGER	read-write	The Port Number for the main link of this resilient link.
INT ecsRLStandbySlot	1.3.6.1.4.1.43.9.3.3.1.3	INTEGER	read-write	The Slot Number for the standby link of this resilient link.
INT ecsRLStandbyPort	1.3.6.1.4.1.43.9.3.3.1.4	INTEGER	read-write	The Port Number for the standby link of this resilient link.
INT ecsRLActiveLink	1.3.6.1.4.1.43.9.3.3.1.5	INTEGER	read-only	The resilient link currently in use for traffic transmission. For a read the attribute indicates which link is active. A new link will always be configured with the main link being the active link. If the link status cannot be determined, the value unknown(1) is returned.
INT ecsResLinkState	1.3.6.1.4.1.43.9.3.3.1.6	INTEGER	read-write
ecsSecureRepeaterLineCards	1.3.6.1.4.1.43.9.4
INT ecsSecureRLCMode	1.3.6.1.4.1.43.9.4.1	INTEGER	read-only	Determines whether the management of Secure Repeater Line Cards is disabled or not.
INT ecsSecureTrapRepRate	1.3.6.1.4.1.43.9.4.2	INTEGER	read-write	Determines the rate at which secure traps are sent for a security violation.
ecsSecureRLCTable	1.3.6.1.4.1.43.9.4.3		not-accessible	A table which allows management of the secure Repeater Line Cards.
ecsSecureRLCEntry	1.3.6.1.4.1.43.9.4.3.1		not-accessible
INT ecsSecRLCSlotIndex	1.3.6.1.4.1.43.9.4.3.1.1	INTEGER	read-only	The secure repeater line card slot index
INT ecsSecRLCPortIndex	1.3.6.1.4.1.43.9.4.3.1.2	INTEGER	read-only	The secure repeater line card port index
INT ecsSecRLCLinkState	1.3.6.1.4.1.43.9.4.3.1.3	INTEGER	read-only	Attribute to determine whether the security features are enabled on this port of the secure Repeater Line Card.
INT ecsSecRLCPortState	1.3.6.1.4.1.43.9.4.3.1.4	INTEGER	read-write	Attribute to determine whether the port can be normally enabled.
INT ecsSecRLCNTKState	1.3.6.1.4.1.43.9.4.3.1.5	INTEGER	read-write	Attribute to determine whether the Need to Know feature is enabled on the secure Repeater Line Card.
INT ecsSecRLCBroadState	1.3.6.1.4.1.43.9.4.3.1.6	INTEGER	read-write	Attribute to determine whether broadcasts are allowed or not allowed to be transmitted.
INT ecsSecRLCMultiState	1.3.6.1.4.1.43.9.4.3.1.7	INTEGER	read-write	Attribute to determine whether multicasts are allowed or not allowed to be transmitted.
INT ecsSecRLCLearnMode	1.3.6.1.4.1.43.9.4.3.1.8	INTEGER	read-write	Attribute to determine the learning mode of the secure repeater line card.
INT ecsSecRLCReportMode	1.3.6.1.4.1.43.9.4.3.1.9	INTEGER	read-write	Attribute to determine the reporting mode of the secure repeater line card.
OCT ecsSecRLCMACAddress	1.3.6.1.4.1.43.9.4.3.1.10	OCTET STRING	read-write	The MAC address in use by the secure repeater line card.
ecsRepeaterLineCard	1.3.6.1.4.1.43.9.5
ecsRLCPortStatisticsTable	1.3.6.1.4.1.43.9.5.1		not-accessible	A table which summaries the statistics for each active port/slot
ecsRLCPortStatisticsEntry	1.3.6.1.4.1.43.9.5.1.1		not-accessible
INT ecsRepeaterSlotIndex	1.3.6.1.4.1.43.9.5.1.1.1	INTEGER	read-only	The repeater slot index.
INT ecsRepeaterPortIndex	1.3.6.1.4.1.43.9.5.1.1.2	INTEGER	read-only	The repeater port index.
INT ecsRepeaterPortState	1.3.6.1.4.1.43.9.5.1.1.3	INTEGER	read-write	The repeater port state.
INT ecsRepeaterPartitionState	1.3.6.1.4.1.43.9.5.1.1.4	INTEGER	read-only	The repeater port partition state.
CTR ecsGoodRcvdFrames	1.3.6.1.4.1.43.9.5.1.1.5	Counter	read-only	The number of good frames which have been received and repeted by the specified port.
CTR ecsTotalByteCount	1.3.6.1.4.1.43.9.5.1.1.6	Counter	read-only	The summation of the total number of bytes which have been received in good frames and repeated by the specified port.
CTR ecsTotalErrorCount	1.3.6.1.4.1.43.9.5.1.1.7	Counter	read-only	The summaration of all of the errors recorded in the PortErrors table for the specified port
CTR ecsRxBroadcastFrames	1.3.6.1.4.1.43.9.5.1.1.8	Counter	read-only	The number of broadcast frames received on this port.
CTR ecsRxMulticastFrames	1.3.6.1.4.1.43.9.5.1.1.9	Counter	read-only	The number of broadcast frames received on this port.
ecsRLCPortErrorTable	1.3.6.1.4.1.43.9.5.2		not-accessible	A table which summaries the error counts for each active port and slot
ecsRLCPortErrorEntry	1.3.6.1.4.1.43.9.5.2.1		not-accessible
INT ecsErrorSlotIndex	1.3.6.1.4.1.43.9.5.2.1.1	INTEGER	read-only	The repeater slot index
INT ecsErrorPortIndex	1.3.6.1.4.1.43.9.5.2.1.2	INTEGER	read-only	The repeater port index.
CTR ecsCollisionsCount	1.3.6.1.4.1.43.9.5.2.1.3	Counter	read-only	A count of every attempt to transmit a frame that involved a collision.
CTR ecsPartitions	1.3.6.1.4.1.43.9.5.2.1.4	Counter	read-only	The count of the number of partitions which have been detected by the specified port.
CTR ecsCarrierSenseErrors	1.3.6.1.4.1.43.9.5.2.1.5	Counter	read-only	The number of carrier sense errors which have been detected by the specified port.
CTR ecsAlignErrors	1.3.6.1.4.1.43.9.5.2.1.6	Counter	read-only	The number of frames with alignment errors which have been received by the specified port.
CTR ecsCRCErrors	1.3.6.1.4.1.43.9.5.2.1.7	Counter	read-only	The number of frames with CRC errors which have been received by the specified port.
CTR ecsJabberErrors	1.3.6.1.4.1.43.9.5.2.1.8	Counter	read-only	The number of jabber errors which have been detected by the specified port.
ecsRLCPortInfoTable	1.3.6.1.4.1.43.9.5.3		not-accessible	A table which summaries the status information for each active port/slot
ecsRLCPortInfoEntry	1.3.6.1.4.1.43.9.5.3.1		not-accessible
INT ecsInfoSlotIndex	1.3.6.1.4.1.43.9.5.3.1.1	INTEGER	read-only	The repeater slot index
INT ecsInfoPortIndex	1.3.6.1.4.1.43.9.5.3.1.2	INTEGER	read-only	The repeater port index
STR ecsInfoPortName	1.3.6.1.4.1.43.9.5.3.1.3	DisplayString	read-write	This is an informational string that could be used to show the name of a port.
INT ecsRepeaterPartitionAlgor	1.3.6.1.4.1.43.9.5.3.1.4	INTEGER	read-write	The current state of the repeater port algorithm.
INT ecsJabberLockProtect	1.3.6.1.4.1.43.9.5.3.1.5	INTEGER	read-write	The current state of the jabber protect switch. This affects all ports on the repeater ULA (not necessarily all ports on the card).
INT ecsPortTest	1.3.6.1.4.1.43.9.5.3.1.6	INTEGER	read-write	The Loopback test is performed on the specified port. This will interrupt traffic on all ports on the repeater ULA (not necessarily all ports on the card in a specified slot) while the test is in progress.
INT ecsPortErrorState	1.3.6.1.4.1.43.9.5.3.1.7	INTEGER	read-write	The error status of the specified port. Under normal conditions this takes the value 'normal' specifying that no error condition has been detected.
INT ecsPortReset	1.3.6.1.4.1.43.9.5.3.1.8	INTEGER	read-write	The specified port is reset. This will interrupt traffic on all ports on the repeater ULA (not necessarily all ports on the card in a specified slot) while the reset is in progress.
INT ecsPortPartitionTraps	1.3.6.1.4.1.43.9.5.3.1.9	INTEGER	read-write	Determines whether partition traps will be sent for this port.
INT ecsPortLinkTraps	1.3.6.1.4.1.43.9.5.3.1.10	INTEGER	read-write	Determines whether link traps will be sent for this port.
INT ecsPortBootState	1.3.6.1.4.1.43.9.5.3.1.11	INTEGER	read-only	Determines whether the port is disabled on boot (DOB), and therefore suitable for resilient link use.
INT ecsPortSLMode	1.3.6.1.4.1.43.9.5.3.1.12	INTEGER	read-write	Determines whether station locate is enabled for this port.
ecsRLCcrcTable	1.3.6.1.4.1.43.9.5.4		not-accessible	Level at which port rate error rate trap is produced.
ecsRLCcrcEntry	1.3.6.1.4.1.43.9.5.4.1		not-accessible	The number of frames with CRC errors which have been received by the specified port.
INT ecsCRCSlotIndex	1.3.6.1.4.1.43.9.5.4.1.1	INTEGER	read-only	The repeater slot index
INT ecsCRCPortIndex	1.3.6.1.4.1.43.9.5.4.1.2	INTEGER	read-only	The repeater port index
GAU ecsCRCErrorRate	1.3.6.1.4.1.43.9.5.4.1.3	Gauge	read-only	The gauge representing the CRC error rate. This is configured using the CRC error rate configuration.
INT ecsCRCThreshold	1.3.6.1.4.1.43.9.5.4.1.4	INTEGER	read-write	Level at which port rate error rate trap is produced.
INT ecsCRCDecRateValue	1.3.6.1.4.1.43.9.5.4.1.5	INTEGER	read-write	VALUE that, along with Rate Units, determines the Rate Interval, (in ns) between decrements of the CRC error guage, Rate Interval = ( Units * Value ).
INT ecsCRCDecRateUnits	1.3.6.1.4.1.43.9.5.4.1.6	INTEGER	read-write	UNITS that, along with Rate value, determine the Rate Interval Rate Interval = ( Units * Value )
INT ecsCRCHysteresisValue	1.3.6.1.4.1.43.9.5.4.1.7	INTEGER	read-write	Specifies the value to which the CRC error guage must fall before another crossing of the threshold results in a trap.
ecsRLCtrafficTable	1.3.6.1.4.1.43.9.5.5		not-accessible	The configuration parameters which must be set up in order to use the traffic rate guage.
ecsRLCtrafficEntry	1.3.6.1.4.1.43.9.5.5.1		not-accessible
INT ecsTrafficSlotIndex	1.3.6.1.4.1.43.9.5.5.1.1	INTEGER	read-only	The repeater slot index
INT ecsTrafficPortIndex	1.3.6.1.4.1.43.9.5.5.1.2	INTEGER	read-only	The repeater port index
GAU ecsTrafficRate	1.3.6.1.4.1.43.9.5.5.1.3	Gauge	read-only	The gauge representing the rate at which good frames have been received and repeated. This is configured using the traffic rate configuration.
INT ecsTrafficThreshold	1.3.6.1.4.1.43.9.5.5.1.4	INTEGER	read-write	Level at which port rate error rate trap is produced.
INT ecsTrafficDecRateValue	1.3.6.1.4.1.43.9.5.5.1.5	INTEGER	read-write	VALUE that, along with Rate Units, determines the Rate Interval, (in ns) between decrements of the CRC error guage, Rate Interval = ( Units * Value ).
INT ecsTrafficDecRateUnits	1.3.6.1.4.1.43.9.5.5.1.6	INTEGER	read-write	UNITS that, along with Rate value, determine the Rate Interval Rate Interval = ( Units * Value )
INT ecsTrafficHysteresisValue	1.3.6.1.4.1.43.9.5.5.1.7	INTEGER	read-write	Specifies the value to which the CRC error guage must fall before another crossing of the threshold results in a trap.
ecsRLCcollisionTable	1.3.6.1.4.1.43.9.5.6		not-accessible	The configuration parameters which must be set up in order to use the collision rate guage.
ecsRLCcollisionEntry	1.3.6.1.4.1.43.9.5.6.1		not-accessible
INT ecsCollisionSlotIndex	1.3.6.1.4.1.43.9.5.6.1.1	INTEGER	read-only	The repeater slot index
INT ecsCollisionPortIndex	1.3.6.1.4.1.43.9.5.6.1.2	INTEGER	read-only	The repeater port index
GAU ecsCollisionRate	1.3.6.1.4.1.43.9.5.6.1.3	Gauge	read-only	The gauge representing the rate at which collisions have been detected. This is configured using the collision rate configuration.
INT ecsCollisionThreshold	1.3.6.1.4.1.43.9.5.6.1.4	INTEGER	read-write	Level at which the collision rate guage will produce a High Collision rate trap.
INT ecsCollisionDecRateValue	1.3.6.1.4.1.43.9.5.6.1.5	INTEGER	read-write	VALUE that, along with Rate Units, determines the Rate Interval, (in ns) between decrements of the CRC error guage, Rate Interval = ( Units * Value ).
INT ecsCollisionDecRateUnits	1.3.6.1.4.1.43.9.5.6.1.6	INTEGER	read-write	UNITS that, along with Rate value, determine the Rate Interval Rate Interval = ( Units * Value )
INT ecsCollisionHysteresisValue	1.3.6.1.4.1.43.9.5.6.1.7	INTEGER	read-write	Specifies the value to which the Collision guage must fall before another crossing of the threshold results in a trap.
ecsRLCjabberTable	1.3.6.1.4.1.43.9.5.7		not-accessible	The configuration parameters which must be set up in order to use the jabber rate guage.
ecsRLCjabberEntry	1.3.6.1.4.1.43.9.5.7.1		not-accessible
INT ecsJabberSlotIndex	1.3.6.1.4.1.43.9.5.7.1.1	INTEGER	read-only	The repeater slot index
INT ecsJabberPortIndex	1.3.6.1.4.1.43.9.5.7.1.2	INTEGER	read-only	The repeater port index
GAU ecsJabberErrorRate	1.3.6.1.4.1.43.9.5.7.1.3	Gauge	read-only	The gauge representing the rate at which jabber errors have been detected. This is configured using the jabber rate configuration.
INT ecsJabberThreshold	1.3.6.1.4.1.43.9.5.7.1.4	INTEGER	read-write	Level at which port rate error rate trap is produced.
INT ecsJabberDecRateValue	1.3.6.1.4.1.43.9.5.7.1.5	INTEGER	read-write	VALUE that, along with Rate Units, determine the Rate Interval, Rate Interval = ( Units * Value )
INT ecsJabberDecRateUnits	1.3.6.1.4.1.43.9.5.7.1.6	INTEGER	read-write	UNITS that, along with Rate value, determine the Rate Interval Rate Interval = ( Units * Value )
INT ecsJabberHysteresisValue	1.3.6.1.4.1.43.9.5.7.1.7	INTEGER	read-write	Specifies the value to which the jabber error guage must fall before another crossing of the threshold results in a trap.
ecsRLCalignTable	1.3.6.1.4.1.43.9.5.8		not-accessible	The configuration parameters which must be set up in order to use the alignment error rate guage.
ecsRLCalignEntry	1.3.6.1.4.1.43.9.5.8.1		not-accessible
INT ecsAlignSlotIndex	1.3.6.1.4.1.43.9.5.8.1.1	INTEGER	read-only	The repeater slot index
INT ecsAlignPortIndex	1.3.6.1.4.1.43.9.5.8.1.2	INTEGER	read-only	The repeater port index
GAU ecsAlignErrorRate	1.3.6.1.4.1.43.9.5.8.1.3	Gauge	read-only	The gauge representing the alignment error rate. This is configured using the alignment error rate configuration.
INT ecsAlignThreshold	1.3.6.1.4.1.43.9.5.8.1.4	INTEGER	read-write	Level at which port rate error rate trap is produced.
INT ecsAlignDecRateValue	1.3.6.1.4.1.43.9.5.8.1.5	INTEGER	read-write	VALUE that, along with Rate Units, determines the Rate Interval, (in ns) between decrements of the CRC error guage, Rate Interval = ( Units * Value ), where UNITS are in ns
INT ecsAlignDecRateUnits	1.3.6.1.4.1.43.9.5.8.1.6	INTEGER	read-write	UNITS that, along with Rate value, determine the Rate Interval Rate Interval = ( Units * Value )
INT ecsAlignHysteresisValue	1.3.6.1.4.1.43.9.5.8.1.7	INTEGER	read-write	Specifies the value to which the CRC error guage must fall before another crossing of the threshold results in a trap.
ecsRLCcarrierTable	1.3.6.1.4.1.43.9.5.9		not-accessible	The configuration parameters which must be set up in order to use the carrier sense error rate guage.
ecsRLCcarrierEntry	1.3.6.1.4.1.43.9.5.9.1		not-accessible
INT ecsCarrierSlotIndex	1.3.6.1.4.1.43.9.5.9.1.1	INTEGER	read-only	The repeater slot index
INT ecsCarrierPortIndex	1.3.6.1.4.1.43.9.5.9.1.2	INTEGER	read-only	The repeater port index
GAU ecsCarrierSenseErrorRate	1.3.6.1.4.1.43.9.5.9.1.3	Gauge	read-only	The gauge representing the rate at which jabber errors have been detected. This is configured using the jabber rate configuration.
INT ecsCarrierSenseThreshold	1.3.6.1.4.1.43.9.5.9.1.4	INTEGER	read-write	Level at which port rate error rate trap is produced.
INT ecsCarrierSenseRateValue	1.3.6.1.4.1.43.9.5.9.1.5	INTEGER	read-write	VALUE that, along with Rate Units, determines the Rate Interval, (in ns) between decrements of the CRC error guage, Rate Interval = ( Units * Value ).
INT ecsCarrierSenseRateUnits	1.3.6.1.4.1.43.9.5.9.1.6	INTEGER	read-write	UNITS that, along with Rate value, determine the Rate Interval Rate Interval = ( Units * Value )
INT ecsCarrierSenseHysteresisValue	1.3.6.1.4.1.43.9.5.9.1.7	INTEGER	read-write	Specifies the value to which the carrier sense error guage must fall before another crossing of the threshold results in a trap.
ecsRLCSlotStatisticsTable	1.3.6.1.4.1.43.9.5.10		not-accessible	A table which summaries the statistics for each active slot
ecsRLCSlotStatisticsEntry	1.3.6.1.4.1.43.9.5.10.1		not-accessible
INT ecsRLCSlotIndex	1.3.6.1.4.1.43.9.5.10.1.1	INTEGER	read-only	The slot number of the Repeater Line Card.
CTR ecsRLCGoodRcvdFrames	1.3.6.1.4.1.43.9.5.10.1.2	Counter	read-only	The number of readable frames received by this slot.
CTR ecsRLCTotalByteCount	1.3.6.1.4.1.43.9.5.10.1.3	Counter	read-only	The number of readable octets received by this Repeater Line Card.
CTR ecsRLCTotalErrorCount	1.3.6.1.4.1.43.9.5.10.1.4	Counter	read-only	The total number of errors received on this slot.
CTR ecsRLCTotalBroadcasts	1.3.6.1.4.1.43.9.5.10.1.5	Counter	read-only	The total number of broadcast frames received on this slot.
CTR ecsRLCTotalMulticasts	1.3.6.1.4.1.43.9.5.10.1.6	Counter	read-only	The total number of multicast frames received on this slot.
ecsRLCSlotErrorTable	1.3.6.1.4.1.43.9.5.11		not-accessible	A table which summaries the error statistics for each active slot
ecsRLCSlotErrorEntry	1.3.6.1.4.1.43.9.5.11.1		not-accessible
INT ecsRLCErrorSlotIndex	1.3.6.1.4.1.43.9.5.11.1.1	INTEGER	read-only	The slot number of the Repeater Line Card for which these error statistics pertain.
CTR ecsRLCCollisionsCount	1.3.6.1.4.1.43.9.5.11.1.2	Counter	read-only	The total number of Collisions Reported for this slot.
CTR ecsRLCPartitions	1.3.6.1.4.1.43.9.5.11.1.3	Counter	read-only	The total number of Partitions Reported for this slot.
CTR ecsRLCCarrierSenseErrors	1.3.6.1.4.1.43.9.5.11.1.4	Counter	read-only	The total number of Carrier Sense erros reported for this slot.
CTR ecsRLCAlignErrors	1.3.6.1.4.1.43.9.5.11.1.5	Counter	read-only	The total number of Alignement errors Reported for this slot.
CTR ecsRLCCRCErrors	1.3.6.1.4.1.43.9.5.11.1.6	Counter	read-only	The total number of CRC errors reported for this slot.
CTR ecsRLCJabberErrors	1.3.6.1.4.1.43.9.5.11.1.7	Counter	read-only	The total number of jabber errors reported for this slot.
ecsRLCStationLocate	1.3.6.1.4.1.43.9.6
INT ecsRLCSizeOfStationLocateDB	1.3.6.1.4.1.43.9.6.1	INTEGER	read-only
INT ecsRLCNumbOfSLEntries	1.3.6.1.4.1.43.9.6.2	INTEGER	read-only
INT ecsRLCSLDataBaseStatus	1.3.6.1.4.1.43.9.6.3	INTEGER	read-write
OCT ecsRLCSLowFilterAddress	1.3.6.1.4.1.43.9.6.4	OCTET STRING	read-write
OCT ecsRLCSLhighFilterAddress	1.3.6.1.4.1.43.9.6.5	OCTET STRING	read-write
ecsRLCStationLocateTable	1.3.6.1.4.1.43.9.6.6		not-accessible
ecsRLCStationLocateEntry	1.3.6.1.4.1.43.9.6.6.1		not-accessible
OCT ecsRLCSLAddress	1.3.6.1.4.1.43.9.6.6.1.1	OCTET STRING	read-only	The MAC Address for which one wishes to locate the slot and port.
INT ecsRLCSLSlotIndex	1.3.6.1.4.1.43.9.6.6.1.2	INTEGER	read-only	The slot number for this MAC address declared in ecsRLCStationAddress.
INT ecsRLCSLPortIndex	1.3.6.1.4.1.43.9.6.6.1.3	INTEGER	read-only	The port number for this MAC address declared in ecsRLCStationAddress.
INT ecsRLCSLStatus	1.3.6.1.4.1.43.9.6.6.1.4	INTEGER	read-write	Writing clear(1) will clear the entry in the LinkBuilder ECS DataBase.
ecsRLCNewStationLocateTable	1.3.6.1.4.1.43.9.6.7		not-accessible
ecsRLCNewStationLocateEntry	1.3.6.1.4.1.43.9.6.7.1		not-accessible
OCT ecsRLCNewSLAddress	1.3.6.1.4.1.43.9.6.7.1.1	OCTET STRING	read-only	The MAC Address for which one wishes to locate the slot and port.
INT ecsRLCNewSLSlotIndex	1.3.6.1.4.1.43.9.6.7.1.2	INTEGER	read-only	The slot number for this MAC address declared in ecsRLCNewSLAddress.
INT ecsRLCNewSLPortIndex	1.3.6.1.4.1.43.9.6.7.1.3	INTEGER	read-only	The port number for this MAC address declared in ecsRLCNewSLAddress.
ecsHubStatistics	1.3.6.1.4.1.43.9.8
CTR ecsHubTotalGoodRcvdFrames	1.3.6.1.4.1.43.9.8.1	Counter	read-only	The number of readable frames received by this slot.
CTR ecsHubTotalByteCount	1.3.6.1.4.1.43.9.8.2	Counter	read-only	The number of readable octets received by this hub.
CTR ecsHubTotalErrorCount	1.3.6.1.4.1.43.9.8.3	Counter	read-only	The total number of errored packets detected on the hub.
CTR ecsHubTotalBroadcasts	1.3.6.1.4.1.43.9.8.4	Counter	read-only	The total number of brodcast packets detected on the hub.
CTR ecsHubTotalMultiFrames	1.3.6.1.4.1.43.9.8.5	Counter	read-only	The total number of multicast packets detected on the hub.
CTR ecsHubTotalCollisionsCount	1.3.6.1.4.1.43.9.8.6	Counter	read-only	The total number of Collisions Reported for the hub.
CTR ecsHubTotalPartitions	1.3.6.1.4.1.43.9.8.7	Counter	read-only	The total number of Partitions Reported for this hub.
CTR ecsHubTotalCarrierSenseErrors	1.3.6.1.4.1.43.9.8.8	Counter	read-only	The total number of Carrier Sense erros reported for this hub.
CTR ecsHubTotalAlignErrors	1.3.6.1.4.1.43.9.8.9	Counter	read-only	The total number of Alignement errors reported for this hub.
CTR ecsHubTotalCRCErrors	1.3.6.1.4.1.43.9.8.10	Counter	read-only	The total number of CRC errors reported for this hub.
CTR ecsHubTotalJabberErrors	1.3.6.1.4.1.43.9.8.11	Counter	read-only	The total number of jabber errors reported for this hub.
ecsVideo	1.3.6.1.4.1.43.9.9
lbecsXENDOFMIB	1.3.6.1.4.1.43.9.255
xecsDummyTable	1.3.6.1.4.1.43.9.255.1		not-accessible	A dummy table which allows management of all tables (an snm bug).
ecsDummyEntry	1.3.6.1.4.1.43.9.255.1.1		not-accessible
INT ecsDummyIndex	1.3.6.1.4.1.43.9.255.1.1.1	INTEGER	read-only
INT ecsDummyValue	1.3.6.1.4.1.43.9.255.1.1.2	INTEGER	read-write	One of the PSUs has failed, the value of ecsPSUStatus is returned to indicate which PSU has failed.
generic	1.3.6.1.4.1.43.10
genExperimental	1.3.6.1.4.1.43.10.1
testData	1.3.6.1.4.1.43.10.1.1
ifExtensions	1.3.6.1.4.1.43.10.1.2
setup	1.3.6.1.4.1.43.10.2
sysLoader	1.3.6.1.4.1.43.10.3
security	1.3.6.1.4.1.43.10.4
gauges	1.3.6.1.4.1.43.10.5
asciiAgent	1.3.6.1.4.1.43.10.6
serialIf	1.3.6.1.4.1.43.10.7
repeaterMgmt	1.3.6.1.4.1.43.10.8
endStation	1.3.6.1.4.1.43.10.9
localSnmp	1.3.6.1.4.1.43.10.10
manager	1.3.6.1.4.1.43.10.11
unusedGeneric12	1.3.6.1.4.1.43.10.12
chassis	1.3.6.1.4.1.43.10.14
mrmResilience	1.3.6.1.4.1.43.10.15
tokenRing	1.3.6.1.4.1.43.10.16
multiRepeater	1.3.6.1.4.1.43.10.17
bridgeMgmt	1.3.6.1.4.1.43.10.18
fault	1.3.6.1.4.1.43.10.19
poll	1.3.6.1.4.1.43.10.20
powerSupply	1.3.6.1.4.1.43.10.21
netBuilder_mib	1.3.6.1.4.1.43.11
lBridgeECS_mib	1.3.6.1.4.1.43.12
deskMan_mib	1.3.6.1.4.1.43.13
linkBuilderMSH_mib	1.3.6.1.4.1.43.14

RFC description

3Com Load Balancing Hub ECS MIB for HubMan II products, providing standard MIB-II groups for network management.

Start monitoring 3Com network hubs with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download LBHUB-ECS-MIB

What Is LBHUB-ECS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description