LANOPTICS-SYSTEM-MIB

All MIBs › LANOPTICS-SYSTEM-MIB

Category: Network Management

Description: Monitors system-level status and inventory on LANoptics network devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is LANOPTICS-SYSTEM-MIB?

LANOPTICS-SYSTEM-MIB is a legacy vendor MIB from LANoptics providing system-level status and hardware inventory objects for their network hub/bridge devices. As a system-level MIB, it would typically expose top-level device identity, uptime, and overall hardware inventory/status objects for the chassis. Its purpose in monitoring is centered on basic hardware presence and system health status for the device as a whole, complementing more specific option MIBs like the bridge option MIB from the same vendor. It likely relies on standard SNMPv2 SMI imports as its only external dependency, consistent with its minimal sample content. It would have been deployed in legacy LANoptics hub installations as the base system MIB loaded alongside vendor option modules, and this LANOPTICS-SYSTEM-MIB guide summarizes the system-level objects likely present.

IPNetwork Monitor allows you to monitor SNMP objects defined in LANOPTICS-SYSTEM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

LANoptics network hub/bridge device

Monitoring Examples

No object names beyond the standard IMPORTS clause were available in the provided data, so a specific table or scalar cannot be cited with confidence. In general terms, an administrator managing a LANoptics hub would be expected to poll this MIB's system-level objects to confirm the device is present and responding and to check overall chassis inventory status, but the specific object names are not confirmed by source data.

What Can Be Monitored

system inventory status
overall device status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

IpAddress
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
lanOptics	1.3.6.1.4.1.224
lanOpticsSystem	1.3.6.1.4.1.224.2
STR snSysDirectory	1.3.6.1.4.1.224.2.1	DisplayString	read-only	Gives the agent directory content (make DOS DIR command on agent directory).
INT snAgentVersion	1.3.6.1.4.1.224.2.2	INTEGER	read-only	Gives the agent major version in the high order word and the minor version in low order word.
lanOpticsSystemCMOS	1.3.6.1.4.1.224.2.3
lanOpticsSystemCMOSIp	1.3.6.1.4.1.224.2.3.1
snSysCMOSIpInterfaceTable	1.3.6.1.4.1.224.2.3.1.1		not-accessible	A list of network interfaces.
snSysCMOSIpInterfaceEntry	1.3.6.1.4.1.224.2.3.1.1.1		not-accessible	An interface entry containing the Ipaddress and net-mask.
IP snSysCMOSIpIpAddr	1.3.6.1.4.1.224.2.3.1.1.1.1	IpAddress	read-write	Gives the interface's IpAddress
IP snSysCMOSIpNetMask	1.3.6.1.4.1.224.2.3.1.1.1.2	IpAddress	read-write	Gives the interfaces's netmask
INT pysmiFakeCol926	1.3.6.1.4.1.224.2.3.1.1.1.4294967295	INTEGER	not-accessible
IP snSysCMOSIpDefGw	1.3.6.1.4.1.224.2.3.1.2	IpAddress	read-write	Gives the agent's default gateway.
INT snSysCMOSIpTFTPOp	1.3.6.1.4.1.224.2.3.1.3	INTEGER	read-write	Gives the TFTP policy: 1 - No TFTP, 2 - Optional, 3 - Always
IP snSysCMOSIpTFTPAddr	1.3.6.1.4.1.224.2.3.1.4	IpAddress	read-write	Gives the TFTP server Ip address.
STR snSysCMOSIpTFTPFileName	1.3.6.1.4.1.224.2.3.1.5	DisplayString	read-write	Gives the boot file name at the server (full path).
INT snSysCMOSIpTFTPDrive	1.3.6.1.4.1.224.2.3.1.6	INTEGER	read-write	Gives the TFTP operation destination drive (value of ASCII character).
lanOpticsSystemCMOSHub	1.3.6.1.4.1.224.2.3.2
snSysCMOSHubSlotConfigTable	1.3.6.1.4.1.224.2.3.2.1		not-accessible	A list of slots entries. Each entry in this table, contains the last 20 operations performed on the slot.
snSysCMOSHubSlotConfigEntry	1.3.6.1.4.1.224.2.3.2.1.1		not-accessible
OCT snSysSlotLastOperations	1.3.6.1.4.1.224.2.3.2.1.1.1	OCTET STRING	read-write	A description of last 20 operations performed, on the slot
INT snSysResetSlotQueue	1.3.6.1.4.1.224.2.3.2.1.1.2	INTEGER	read-write	Resets the last 20 operations queue.
INT pysmiFakeCol927	1.3.6.1.4.1.224.2.3.2.1.1.4294967295	INTEGER	not-accessible
INT snSysCMOSHubSaveHubFunctions	1.3.6.1.4.1.224.2.3.2.2	INTEGER	read-write	Save (2) /Do not Save (1) Hub managment functions in non-volatile memory.
lanOpticsSystemCMOSRPL	1.3.6.1.4.1.224.2.3.3
INT snSysCMOSRPLMode	1.3.6.1.4.1.224.2.3.3.1	INTEGER	read-write	Determine if the image will be loaded through RPL at next boot: RPL off - 1, RPL on - 2.
INT snSysCMOSFlashMode	1.3.6.1.4.1.224.2.3.3.2	INTEGER	read-write	Determine if the image will be loaded from flash memory at next boot : flash on - 2, flash off - 1.
lanOpticsSystemCMOSSerial	1.3.6.1.4.1.224.2.3.4
INT snSysCMOSSerialMode	1.3.6.1.4.1.224.2.3.4.1	INTEGER	read-write	Determine the serial port usage mode : Proprietary - 1, SLIP - 2, None - 3.
INT snSysCMOSSerialComSelect	1.3.6.1.4.1.224.2.3.4.2	INTEGER	read-write	Determine which COM port is used.
INT snSysCMOSSerialBaudRate	1.3.6.1.4.1.224.2.3.4.3	INTEGER	read-write	Determine the serial port baud rate : 1200 - 1, 2400 - 2, 4800 - 3, 9600 - 4, 19200 - 5, 38300 - 6, 57600 - 7
INT snSysCMOSSerialWordLength	1.3.6.1.4.1.224.2.3.4.4	INTEGER	read-write	Determine the data bits length : 7 Bits - 1, 8 Bits -2
INT snSysCMOSSerialStopBits	1.3.6.1.4.1.224.2.3.4.5	INTEGER	read-write	Determine the number of stop bits; values allowed : 1 Bit - 1, 1.5 Bits - 2, 2 Bits - 3.
INT snSysCMOSSerialParityCheck	1.3.6.1.4.1.224.2.3.4.6	INTEGER	read-write	Determine the parity check policy : Even - 1, Odd - 2, None - 3.
lanOpticsSystemCMOSSRAM	1.3.6.1.4.1.224.2.3.5
INT snSysCMOSSRAMKeepAliveSecInterval	1.3.6.1.4.1.224.2.3.5.1	INTEGER	read-write	Determine the interval of the keep alive frame in seconds
lanOpticsSystemCMOSSNMP	1.3.6.1.4.1.224.2.3.6
INT snSysCMOSSNMPCommunitiesNum	1.3.6.1.4.1.224.2.3.6.1	INTEGER	read-only	Keeps the number of communities.
INT snSysCMOSSNMPTrapManagersNum	1.3.6.1.4.1.224.2.3.6.2	INTEGER	read-only	Keeps the number of managers that traps are send to.
snSysCMOSSNMPCommunitiesTable	1.3.6.1.4.1.224.2.3.6.3		not-accessible	A table containing the SNMP communities
snSysCMOSSNMPCommunitiesEntry	1.3.6.1.4.1.224.2.3.6.3.1		not-accessible	An entry community info
STR snSysCMOSSNMPCommunityName	1.3.6.1.4.1.224.2.3.6.3.1.1	DisplayString	read-write	This variable will give the community name.
INT snSysCMOSSNMPCommunityPrivs	1.3.6.1.4.1.224.2.3.6.3.1.2	INTEGER	read-write	This variable will give the community privilages: Read Only - 1, Read/Write - 2.
INT pysmiFakeCol928	1.3.6.1.4.1.224.2.3.6.3.1.4294967295	INTEGER	not-accessible
snSysCMOSSNMPTrapCommunitiesTable	1.3.6.1.4.1.224.2.3.6.4		not-accessible	A table containing the SNMP communities
snSysCMOSSNMPTrapCommunitiesEntry	1.3.6.1.4.1.224.2.3.6.4.1		not-accessible	An entry of trap IP destinations.
IP snSysCMOSSNMPTrapCommunityIpAddr	1.3.6.1.4.1.224.2.3.6.4.1.1	IpAddress	read-write	This variable gives a manager IP address for traps destination.
INT pysmiFakeCol929	1.3.6.1.4.1.224.2.3.6.4.1.4294967295	INTEGER	not-accessible
lanOpticsSystemCMOSACCESS	1.3.6.1.4.1.224.2.3.7
INT snSysCMOSACCESSOffset	1.3.6.1.4.1.224.2.3.7.1	INTEGER	read-write	Gives the offset in the CMOS array. For internal use only
INT snSysCMOSACCESSLength	1.3.6.1.4.1.224.2.3.7.2	INTEGER	read-write	Gives the length (max 512) in the CMOS array. For internal use only,
INT snSysCMOSACCESSSequence	1.3.6.1.4.1.224.2.3.7.3	INTEGER	read-write	Gives a sequnce of bytes from CMOS array. For internal use only
lanOpticsSystemCMOSBRDG	1.3.6.1.4.1.224.2.3.8
INT snSysCMOSBRDGradius	1.3.6.1.4.1.224.2.3.8.1	INTEGER	read-write	Sets the discovery radius. Value = 0-7. 0=disable bridge.
INT snSysCMOSBRDGlinkNumber	1.3.6.1.4.1.224.2.3.8.2	INTEGER	read-write	Sets the Link number. Value = 0-3.
STR snSysCMOSBRDGpassword	1.3.6.1.4.1.224.2.3.8.3	DisplayString	read-write	Sets the bridge password. 8 characters .

RFC description

LanOptics network system MIB providing IP configuration, hub management, and device information.

Start monitoring LANoptics network hub/bridge device (system-level status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download LANOPTICS-SYSTEM-MIB

What Is LANOPTICS-SYSTEM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description