INNOVX-DTE-MIB

All MIBs › INNOVX-DTE-MIB

Category: Domain: Telco/Transport, Domain: WAN, Vendor: InnoVX

Description: InnoVX MIB for monitoring and configuring data terminal equipment (DTE) interfaces in WAN access devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is INNOVX-DTE-MIB?

INNOVX-DTE-MIB is a vendor MIB from InnoVX for managing Data Terminal Equipment (DTE) serial interfaces on WAN access devices such as modems or CSU/DSU-style units. It exposes interface type and timing configuration, carrier and control-signal status (RxCarrier, DsrControl), loopback test configuration, diagnostic test status/duration, and port/LED status. It is explicitly used to monitor the physical hardware status of serial WAN links: carrier detect state, DTR loss alarm severity, port LED indicators, and diagnostic self-test results all serve as fault indicators for a serial connection. It likely complements standard RS-232/V.35 DTE/DCE conventions and the device's ifIndex-based interface numbering, though it is not tied to a specific IETF standard MIB. It is deployed on InnoVX WAN access equipment where INNOVX-DTE-MIB SNMP monitoring gives administrators visibility into serial line signaling and diagnostic health.

IPNetwork Monitor allows you to monitor SNMP objects defined in INNOVX-DTE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

InnoVX WAN access devices
serial DTE/modem equipment

Monitoring Examples

An administrator would poll dteRxCarrier and dtePortStatus for a given serial interface to detect loss of the carrier signal on a WAN link, and watch for a dteDtrLossTrapSeverity trap indicating the DTR control signal has dropped, often signaling a disconnected cable or failed remote device. dteDiagTestStatus and dteDiagTestDuration would be checked after initiating a dteLoopback test to confirm the interface passed self-diagnostics. dteLedStatus provides a quick hardware-indicator cross-check against the reported port status.

What Can Be Monitored

carrier detect status
DSR control state
DTR loss alarm severity
loopback test mode/status
diagnostic test status and duration
port and LED status

Imported Objects

From INNOVX-CORE-MIB

dteGroup

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
dteAdmin	1.3.6.1.4.1.498.22.1.6.1
STR dtesMIBversion	1.3.6.1.4.1.498.22.1.6.1.1	DisplayString	read-only	Identifies the version of the MIB as `X.YZT' where: X: Major Revision (1-9) Y: Minor Revision (0-9) Z: Typographical Revision (0-9) T: Test Revision (A-Z) Upon formal release, the test revision will not be present.
dteCfg	1.3.6.1.4.1.498.22.1.6.2
INT dteInterfaceType	1.3.6.1.4.1.498.22.1.6.2.1	INTEGER	read-write	Defines the DTE Interface Type. WEBFLAG V.28 V.35 RS-449 EIA-530 EIA-530A X.21 WEBEND
INT dteTxInvertingTiming	1.3.6.1.4.1.498.22.1.6.2.2	INTEGER	read-write	normal(1) tx timing clocks the transmit data from the DTE using an internal generated clock. invert (2) Invert Internally generated transmit clock used to sample the transmit data from the DTE. external(3) uses the DTE clock, EXTCLK, to clock the transmit data from the DTE. WEBFLAG Slave Normal Slave Inverted External WEBEND
INT dteRxCarrier	1.3.6.1.4.1.498.22.1.6.2.3	INTEGER	read-write	The Receive Carrier option. This option controls the operation of DCD. WEBFLAG Forced On Normal Operation WEBEND
INT dteDsrControl	1.3.6.1.4.1.498.22.1.6.2.4	INTEGER	read-write	The DSR option. This option controls the operation of DSR. When forcedOn(1) is selected, DSR is normally on, if set for followsDTR(2) then DSR is on only when DTR is on. WEBFLAG Forced On Follows DTR WEBEND
dteAlarmCfg	1.3.6.1.4.1.498.22.1.6.3
INT dteDtrLossTrapSeverity	1.3.6.1.4.1.498.22.1.6.3.1	INTEGER	read-write	Controls the reporting and defines the severity of the Channel Data Terminal Ready Loss Alarm when this event occurs. WEBFLAG Inhibit Critical Major Minor Warning Info WEBEND
dteDiagnostics	1.3.6.1.4.1.498.22.1.6.4
INT dteLoopback	1.3.6.1.4.1.498.22.1.6.4.1	INTEGER	read-write	Control the DTE loopback to the channel. noTest(1) stops the test. toChan(2) starts a loopback toward the DTE.
INT dteDiagTestDuration	1.3.6.1.4.1.498.22.1.6.4.2	INTEGER	read-write	Defines the length of the diagnostic test.
INT dteDiagTestStatus	1.3.6.1.4.1.498.22.1.6.4.3	INTEGER	read-only	Displays the test in progress, if any.
dteStatus	1.3.6.1.4.1.498.22.1.6.5
OCT dteLedStatus	1.3.6.1.4.1.498.22.1.6.5.1	OCTET STRING	read-only	A bitwise snapshot of the front panel LED states, where 0 = LED off and 1 = LED on, as follows: LED description Octet 1 bit 7 - n/u bit 6 - n/u bit 5 - n/u bit 4 - n/u bit 3 - n/u bit 2 - DTE LMI LMI traffic on DTE bit 1 - SD EQP send data - equipment traffic bit 0 - RD EQP receive data - equipment traffic
OCT dtePortStatus	1.3.6.1.4.1.498.22.1.6.5.2	OCTET STRING	read-only	A bitwise snapshot of interface port status conditions and EIA signals, where 0 = condition not present, and 1 = condition present, as follows: Octet 1 - DTE Interface Port Status bit 7 - n/u bit 6 - n/u bit 5 - n/u bit 4 - n/u bit 3 - n/u bit 2 - Transmit Activity bit 1 - Receive Activity bit 0 - DTR Loss
OCT dtePortFrameCounts	1.3.6.1.4.1.498.22.1.6.5.3	OCTET STRING	read-only	The total number of frames transmitted and received on each interface port. This object will be reset to zero after a read, and after power up, soft reset, or factory defaults reset. Octet 1 - DTE Interface Transmit Frame Count Octet 2 bit 7 - 2^15 bit 7 - 2^7 bit 6 - 2^14 bit 6 - 2^6 bit 5 - 2^13 bit 5 - 2^5 bit 4 - 2^12 bit 4 - 2^4 bit 3 - 2^11 bit 3 - 2^3 bit 2 - 2^10 bit 2 - 2^2 bit 1 - 2^9 bit 1 - 2^1 bit 0 - 2^8 bit 0 - 2^0 Octet 3 - DTE Interface Receive Frame Count Octet 4 bit 7 - 2^15 bit 7 - 2^7 bit 6 - 2^14 bit 6 - 2^6 bit 5 - 2^13 bit 5 - 2^5 bit 4 - 2^12 bit 4 - 2^4 bit 3 - 2^11 bit 3 - 2^3 bit 2 - 2^10 bit 2 - 2^2 bit 1 - 2^9 bit 1 - 2^1 bit 0 - 2^8 bit 0 - 2^0

RFC description

DTE interface management and diagnostics for Innovx Access Probe systems.

Start monitoring InnoVX WAN access device / serial DTE-DCE equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download INNOVX-DTE-MIB

What Is INNOVX-DTE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description