All MIBs › HUAWEI-VDSL2-LINE-MIB
Organization: Huawei Technologies Co.,Ltd.
Last Updated: 2012-12-31
Description: HUAWEI-VDSL2-LINE-MIB module
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HUAWEI-VDSL2-LINE-MIB?
HUAWEI-VDSL2-LINE-MIB is a Huawei enterprise MIB for managing VDSL2 broadband access lines on Huawei DSLAM/access equipment, part of the wireline broadband access technology area. It exposes per-line configuration and status objects for VDSL2 physical layer parameters such as line profile, operating mode, and line state. Its monitoring purpose is largely performance and status oriented: it is used to check whether a subscriber's DSL line is up, synchronized, and operating within its configured profile, functioning as a hardware/line-health indicator for the copper access loop. It conceptually parallels the IETF/ITU VDSL2-LINE-MIB and ITU-T G.993.2 standard but is implemented as a Huawei-specific module for Huawei access platforms. It is deployed on Huawei broadband access nodes (DSLAMs/MSANs) serving VDSL2 subscriber lines. Network engineers evaluating or troubleshooting this functionality can download the HUAWEI-VDSL2-LINE-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-VDSL2-LINE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei DSLAM
- Huawei broadband access node/MSAN
Monitoring Examples
Since no sample_objects were supplied, a plausible structure would be a per-line table (e.g., hwVdsl2LineTable/Entry) indexed by physical port, with fields for line status, upstream/downstream sync rate, and noise margin. An administrator would poll line status and sync rate to detect a line that has dropped sync or is running at a degraded rate, indicating copper-line noise or a wiring fault affecting a subscriber's broadband service.
What Can Be Monitored
- VDSL2 line status
- upstream/downstream sync rate
- line profile/configuration
- noise margin
- line up/down state
This MIB depends on
Related MIBs
Imported Objects
From HC-PerfHist-TC-MIB
| HCPerfIntervalThreshold | |
| HCPerfTimeElapsed |
From HUAWEI-DEVICE-MIB
| hwConfigChangeIP | |
| hwFrameIndex | OBJECT-TYPE |
| hwPortIndex | OBJECT-TYPE |
| hwPortOperStatus | OBJECT-TYPE |
| hwPortPrimaryStatus | |
| hwPortSecondaryStatus | |
| hwSlotIndex | OBJECT-TYPE |
From HUAWEI-MIB
| huaweiUtility | OBJECT-IDENTITY |
| Vdsl2Actmode | |
| Vdsl2AutoProfile | |
| Vdsl2BandOptUsage | |
| Vdsl2BandPlan | |
| Vdsl2BitSwap | |
| Vdsl2CfgMode | |
| Vdsl2ChAtmStatus | |
| Vdsl2ChEnabling | |
| Vdsl2ChPtmStatus | |
| Vdsl2ConfPmsForce | |
| Vdsl2DataPathMode | |
| Vdsl2DataPathModeType | |
| Vdsl2Direction | |
| Vdsl2DpboEpsd | |
| Vdsl2DpboEscm | |
| Vdsl2ForceINP | |
| Vdsl2InitResult | |
| Vdsl2LConfProfPmMode | |
| Vdsl2LastTransmittedState | |
| Vdsl2LdsfResult | |
| Vdsl2LineLdsf | |
| Vdsl2LineStatus | |
| Vdsl2MaxBer | |
| Vdsl2OperationModes | |
| Vdsl2PSDClassMask | |
| Vdsl2PhyRControl | |
| Vdsl2PowerMngState | |
| Vdsl2ProfSwitchType | |
| Vdsl2Profiles | |
| Vdsl2PsdLimitMask | |
| Vdsl2PsdMaskDs | |
| Vdsl2PsdMaskUs | |
| Vdsl2RaMode | |
| Vdsl2Rfi | |
| Vdsl2ScMaskDs | |
| Vdsl2ScMaskUs | |
| Vdsl2StatusRtxUsed | |
| Vdsl2SubProfiles | |
| Vdsl2SubProfilesWeight | |
| Vdsl2SymbolProtectionDs | |
| Vdsl2SymbolProtectionUs | |
| Vdsl2TIPsdClassMask | |
| Vdsl2TransmissionModeType | |
| Vdsl2Tssi | |
| Vdsl2Unit | |
| Vdsl2UpboBoostMode | |
| Vdsl2UpboKl0RefBand | |
| Vdsl2UpboKlf | |
| Vdsl2UpboPsdBand | |
| Vdsl2UpsPsdMaskSelection | |
| Vdsl2Us0Disable | |
| Vdsl2Us0PsdMask | |
| Vdsl2VirtualNoise | |
| Vdsl2VirtualNoiseDs | |
| Vdsl2VirtualNoiseUs | |
| Vdsl2vdsltoneblackout | |
| Xdsl2Band |
| hwXdslProfName | OBJECT-TYPE |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DateAndTime | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using vdsl2PMLCurr15MFecs OID:
Select a Huawei DSLAM/broadband access node/MSAN (VDSL2 line) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type vdsl2PMLCurr15MFecs into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline (in seconds), since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| vdslMIB | 1.3.6.1.4.1.2011.6.115 | This mib is used for defining huawei's VDSL line management MIB objects. | ||
| vdsl2 | 1.3.6.1.4.1.2011.6.115.1 | |||
| vdsl2Notifications | 1.3.6.1.4.1.2011.6.115.1.0 | |||
| NTF vdsl2LinePerfFECSThreshXtuc | 1.3.6.1.4.1.2011.6.115.1.0.1 | This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred xTU-C. | ||
| NTF vdsl2LinePerfFECSThreshXtur | 1.3.6.1.4.1.2011.6.115.1.0.2 | This notification indicates that the FEC seconds threshold has been reached/exceeded for the referred xTU-R. | ||
| NTF vdsl2LinePerfESThreshXtuc | 1.3.6.1.4.1.2011.6.115.1.0.3 | This notification indicates that the errored seconds threshold has been reached/exceeded for the referred xTU-C. | ||
| NTF vdsl2LinePerfESThreshXtur | 1.3.6.1.4.1.2011.6.115.1.0.4 | This notification indicates that the errored seconds threshold has been reached/exceeded for the referred xTU-R. | ||
| NTF vdsl2LinePerfSESThreshXtuc | 1.3.6.1.4.1.2011.6.115.1.0.5 | This notification indicates that the severely-errored seconds threshold has been reached/exceeded for the referred xTU-C. | ||
| NTF vdsl2LinePerfSESThreshXtur | 1.3.6.1.4.1.2011.6.115.1.0.6 | This notification indicates that the severely-errored seconds threshold has been reached/exceeded for the referred xTU-R. | ||
| NTF vdsl2LinePerfLOSSThreshXtuc | 1.3.6.1.4.1.2011.6.115.1.0.7 | This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred xTU-C. | ||
| NTF vdsl2LinePerfLOSSThreshXtur | 1.3.6.1.4.1.2011.6.115.1.0.8 | This notification indicates that the LOS seconds threshold has been reached/exceeded for the referred xTU-R. | ||
| NTF vdsl2LinePerfUASThreshXtuc | 1.3.6.1.4.1.2011.6.115.1.0.9 | This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred xTU-C. | ||
| NTF vdsl2LinePerfUASThreshXtur | 1.3.6.1.4.1.2011.6.115.1.0.10 | This notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred xTU-R. | ||
| NTF vdsl2LinePerfCodingViolationsThreshXtuc | 1.3.6.1.4.1.2011.6.115.1.0.11 | This notification indicates that the coding violations threshold has been reached/exceeded for the referred xTU-C. | ||
| NTF vdsl2LinePerfCodingViolationsThreshXtur | 1.3.6.1.4.1.2011.6.115.1.0.12 | This notification indicates that the coding violations threshold has been reached/exceeded for the referred xTU-R. | ||
| NTF vdsl2LinePerfCorrectedThreshXtuc | 1.3.6.1.4.1.2011.6.115.1.0.13 | This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred xTU-C. | ||
| NTF vdsl2LinePerfCorrectedThreshXtur | 1.3.6.1.4.1.2011.6.115.1.0.14 | This notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred xTU-R. | ||
| NTF vdsl2LinePerfFailedFullInitThresh | 1.3.6.1.4.1.2011.6.115.1.0.15 | This notification indicates that the failed full initializations threshold has been reached/exceeded for the referred VDSL/VDSL2 or VDSL2 line. | ||
| NTF vdsl2LinePerfFailedShortInitThresh | 1.3.6.1.4.1.2011.6.115.1.0.16 | This notification indicates that the failed short initializations threshold has been reached/exceeded for the referred VDSL or VDSL2 line. | ||
| NTF vdsl2LineStatusChangeXtuc | 1.3.6.1.4.1.2011.6.115.1.0.17 | This notification indicates that a status change is detected for the referred xTU-C. | ||
| NTF vdsl2LineStatusChangeXtur | 1.3.6.1.4.1.2011.6.115.1.0.18 | This notification indicates that a status change is detected for the referred xTU-R. | ||
| NTF vdsl2LinePerfFullInitThresh | 1.3.6.1.4.1.2011.6.115.1.0.19 | This notification indicates that the full initializations threshold has been reached/exceeded for the referred VDSL/VDSL2 or VDSL2 line. | ||
| vdsl2Line | 1.3.6.1.4.1.2011.6.115.1.1 | |||
| vdsl2LineTable | 1.3.6.1.4.1.2011.6.115.1.1.1 | not-accessible | The table vdsl2LineTable contains configuration, command and status parameters of the VDSL2 line. The index of this table is ifIndex. | |
| vdsl2LineEntry | 1.3.6.1.4.1.2011.6.115.1.1.1.1 | not-accessible | The table vdsl2LineTable contains configuration, command and status parameters of the VDSL2 line. The index of this entry is ifIndex. | |
| OCT vdsl2LineCnfgTemplate | 1.3.6.1.4.1.2011.6.115.1.1.1.1.1 | OCTET STRING | read-write | The value of this object identifies the row in the VDSL2 Line Configuration Templates Table, (Vdsl2ConfTemplatesTable), which applies for this VDSL2 line. |
| OCT vdsl2LineAlarmCnfgTemplate | 1.3.6.1.4.1.2011.6.115.1.1.1.1.2 | OCTET STRING | read-write | The value of this object identifies the row in the VDSL2 Line Alarm Configuration Template Table, (vdsl2LineAlarmConfTemplateTable), which applies to this VDSL2 line. |
| VDS vdsl2LineCmndConfPmsf | 1.3.6.1.4.1.2011.6.115.1.1.1.1.3 | Vdsl2ConfPmsForce | read-write | Power management state forced. Defines the line states to be forced by the near-end xTU on this line. Options: 1. l3toL0(0) - Force the line to transition from the L3 idle state to the L0 full-on state 2. l0toL2(2) - Force the line to transition from L0 full on to L2 low power state 3. l0orL2toL3(3) - Force the line to transition from the L0 full-on or L2 low power state to the L3 idle state 4. invalidValue(-1) -Invalid value |
| VDS vdsl2LineCmndConfLdsf | 1.3.6.1.4.1.2011.6.115.1.1.1.1.4 | Vdsl2LineLdsf | read-write | Loop diagnostics mode forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end xTU on this line or only be responsive to loop diagnostics initiated by the far-end xTU. |
| VDS vdsl2LineCmndConfLdsfFailReason | 1.3.6.1.4.1.2011.6.115.1.1.1.1.5 | Vdsl2LdsfResult | read-only | The status of the recent occasion the Loop diagnostics mode forced (LDSF) was issued for the associated line. Options: 1. none(1) - The default value in case LDSF was never requested for the associated line 2. success(2) - The recent command completed successfully 3. inProgress(3) - The Loop Diagnostics process is in progress 4. unsupported(4) - The NE or the line card doesn't support LDSF 5. cannotRun(5) - The NE cannot initiate the command, due to a non specific reason 6. aborted(6) - The Loop Diagnostics process aborted 7. failed(7) - The Loop Diagnostics process failed 8. illegalMode(8) - The NE cannot initiate the command, due to the specific mode of the relevant line 9. adminUp(9) - The NE cannot initiate the command, as the relevant line is administratively 'Up' 10.tableFull(10) - The NE cannot initiate the command, due to reaching the maximum number of rows in the results table 11.noResources(11) - The NE cannot initiate the command, due to lack of internal memory resources Default: none(1) |
| T/F vdsl2LineCmndAutomodeColdStart | 1.3.6.1.4.1.2011.6.115.1.1.1.1.6 | TruthValue | read-write | Automode cold start forced. This parameter is defined in order to improve testing of the performance of ATUs supporting automode when it is enabled in the MIB. Change the value of this parameter to 'true' indicates a change in loop conditions applied to the devices under test. The ATUs shall reset any historical information used for automode and for shortening G.994.1 handshake and initialization. Automode is the case where multiple operation-modes are enabled through the vdsl2LConfProfXtuTransSysEna object in the line configuration profile being used for the VDSL line, and where the selection of the actual operation-mode depends not only on the common capabilities of both ATUs (as exchanged in G.994.1), but also on achievable data rates under given loop conditions. |
| U32 vdsl2LineStatusXtuTransSys | 1.3.6.1.4.1.2011.6.115.1.1.1.1.7 | Unsigned32 | read-only | The xTU Transmission System (XTS) in use. This parameter may be derived from the handshaking procedures defined in Recommendation G.994.1. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. One of VDSL2 line transmission modes: ANSI-T1413(1) ETSI-DTS-TM06006(2) G9921-POTS-NONOVERLAP(3) G9921-POTS-OVERLAP(4) G9921-ISDN-NONOVERLAP(5) G9921-ISDN-OVERLAP(6) G9921-TCMISDN-NONOVERLAP(7) G9921-TCMISDN-OVERLAP(8) G9922-POTS-NONOVERLAP(9) G9922-POTS-OVERLAP(10) G9922-TCMISDN-NONOVERLAP(11) G9922-TCMISDN-OVERLAP(12) G9921-TCMISDN-SYMMETRIC(13) G9923-POTS-NONOVERLAP(19) G9923-POTS-OVERLAP(20) G9923-ISDN-NONOVERLAP(21) G9923-ISDN-OVERLAP(22) G9924-POTS-NONOVERLAP(25) G9924-POTS-OVERLAP(26) G9923-ANNEXI-ALLDIGI-NONOVERLAP(29) G9923-ANNEXI-ALLDIGI-OVERLAP(30) G9923-ANNEXJ-ALLDIGI-NONOVERLAP(31) G9923-ANNEXJ-ALLDIGI-OVERLAP(32) G9924-ANNEXI-ALLDIGI-NONOVERLAP(33) G9924-ANNEXI-ALLDIGI-OVERLAP(34) G9923-ANNEXL-POTS-NONOVERLAP-MODE1-WIDEUS(35) G9923-ANNEXL-POTS-NONOVERLAP-MODE2-NARROWUS(36) G9923-ANNEXL-POTS-OVERLAP-MODE3-WIDEUS(37) G9923-ANNEXL-POTS-NONOVERLAP-MODE4-NARROWUS(38) G9923-ANNEXM-POTS-NONOVERLAP(39) G9923-ANNEXM-POTS-OVERLAP(40) G9925-POTS-NONOVERLAP(41) G9925-POTS-OVERLAP(42) G9925-ISDN-NONOVERLAP(43) G9925-ISDN-OVERLAP(44) G9925-ANNEXI-ALLDIGI-NONOVERLAP(47) G9925-ANNEXI-ALLDIGI-OVERLAP(48) G9925-ANNEXJ-ALLDIGI-NONOVERLAP(49) G9925-ANNEXJ-ALLDIGI-OVERLAP(50) G9925-ANNEXM-POTS-NONOVERLAP(51) G9925-ANNEXM-POTS-OVERLAP(52) G9931(65) G9932-ANNEXA-POTS(73) G9932-ANNEXA-ISDN(74) G9932-ANNEXB-POTS(75) G9932-ANNEXB-ISDN(76) G9932-ANNEXC-POTS(77) G9932-ANNEXC-ISDN(78) G9935(79) G9935-FRIENDLY-DS(80) G9935-FULL-FRIENDLY(81) |
| VDS vdsl2LineStatusPwrMngState | 1.3.6.1.4.1.2011.6.115.1.1.1.1.8 | Vdsl2PowerMngState | read-only | The current power management state. Options: 1. L0 - Synchronized and full transmission 2. L1 - Low Power with reduced net data rate 3. L2 - Low Power with reduced net data rate 4. L3 - No power The various possible values are:l0(0), l1(1), l2(2), l3(3). |
| VDS vdsl2LineStatusInitResult | 1.3.6.1.4.1.2011.6.115.1.1.1.1.9 | Vdsl2InitResult | read-only | Indicates the result of the last full initialization performed on the line. Options: 1. noFail (0) - Successful initialization 2. configError (1) - Configuration failure 3. configNotFeasible (2) - Configuration details not supported 4. commFail (3) - Communication failure 5. noPeerXtu (4) - Peer xTU not detected 6. otherCause (5) - Other initialization failure reason 7. ginpNotSelected(6) - G.998.4 Retransmission mode was not selected while RTX-MODE = FORCED or with RTX-MODE = RTX-TESTMODE 8. invalidValue(-1) - Invalid value |
| VDS vdsl2LineStatusLastStateDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.10 | Vdsl2LastTransmittedState | read-only | The last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line. States are per the specific VDSL type and are counted from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime. |
| VDS vdsl2LineStatusLastStateUs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.11 | Vdsl2LastTransmittedState | read-only | The last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line. States are per the specific VDSL type and are counted from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime. |
| VDS vdsl2LineStatusXtur | 1.3.6.1.4.1.2011.6.115.1.1.1.1.12 | Vdsl2LineStatus | read-only | Indicates current state (existing failures) of the xTU-R. This is a bit-map of possible conditions. The various bit positions are: noFailure(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), initFailure(4) - never active on xTU-R |
| VDS vdsl2LineStatusXtuc | 1.3.6.1.4.1.2011.6.115.1.1.1.1.13 | Vdsl2LineStatus | read-only | Indicates current state (existing failures) of the xTU-C. This is a bit-map of possible conditions. This BITS structure can report the following failures: 1. noDefect (0) - This bit position positively reports that no defect or failure exist 2. lossOfFraming (1) - Loss of frame synchronization 3. lossOfSignal (2) - Loss of signal 4. lossOfPower (3) - Loss of power. Usually this failure may be reported for CPE units only 5. initFailure (4) - Recent initialization process failed |
| U32 vdsl2LineStatusLnAttenDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.14 | Unsigned32 | read-only | The measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all sub-carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A value of all 1's indicates the line attenuation is out of range to be represented. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1 dB |
| U32 vdsl2LineStatusLnAttenUs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.15 | Unsigned32 | read-only | The measured difference in the total power transmitted by the xTU-R and the total power received by the xTU-C over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A value of all 1's indicates the line attenuation is out of range to be represented. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1 dB |
| U32 vdsl2LineStatusSigAttenDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.16 | Unsigned32 | read-only | The measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A value of all 1's indicates the line attenuation is out of range to be represented. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1 dB |
| U32 vdsl2LineStatusSigAttenUs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.17 | Unsigned32 | read-only | The measured difference in the total power transmitted by the xTU-R and the total power received by the xTU-C over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A value of all 1's indicates the line attenuation is out of range to be represented. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1 dB |
| I32 vdsl2LineStatusSnrMarginDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.18 | Integer32 | read-only | Downstream SNR Margin is the maximum increase in dB of the noise power received at the xTU-R, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (Physical values are -64 to 63 dB). A value of 0x7FFFFFFF(2147483647) indicates the line attenuation is out of range to be represented. The invalid value is 2147483647. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1 dB |
| I32 vdsl2LineStatusSnrMarginUs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.19 | Integer32 | read-only | Upstream SNR Margin is the maximum increase in dB of the noise power received at the xTU-C, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (Physical values are -64 to 63 dB). A value of 0x7FFFFFFF(2147483647) indicates the line attenuation is out of range to be represented. The invalid value is 2147483647. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1 dB |
| U32 vdsl2LineStatusAttainableRateDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.20 | Unsigned32 | read-only | Maximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the xTU-C transmitter and the xTU-R receiver, coded in bit/s. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: bits/second |
| U32 vdsl2LineStatusAttainableRateUs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.21 | Unsigned32 | read-only | Maximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the xTU-R transmitter and the xTU-C receiver, coded in bit/s. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: bits/second |
| I32 vdsl2LineStatusActPsdDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.22 | Integer32 | read-only | Actual Power Spectrum Density (PSD) Downstream. The average downstream transmit PSD over the sub-carriers used for downstream. It ranges from -900 to 0 units of 0.1 dB (Physical values are -90 to 0 dBm/Hz). A value of 0x7FFFFFFF(2147483647) indicates the measurement is out of range to be represented. The invalid value is 2147483647. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1 dB |
| I32 vdsl2LineStatusActPsdUs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.23 | Integer32 | read-only | Actual Power Spectrum Density (PSD) Upstream. The average upstream transmit PSD over the sub-carriers used for upstream. It ranges from -900 to 0 units of 0.1 dB (Physical values are -90 to 0 dBm/Hz). A value of 0x7FFFFFFF(2147483647) indicates the measurement is out of range to be represented. The invalid value is 2147483647. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1 dB |
| I32 vdsl2LineStatusActAtpDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.24 | Integer32 | read-only | Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the xTU-C at the U-C reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical values are -31 to 31 dBm). A value of 0x7FFFFFFF(2147483647) indicates the measurement is out of range to be represented. The invalid value is 2147483647. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1 dB |
| I32 vdsl2LineStatusActAtpUs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.25 | Integer32 | read-only | Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the xTU-R at the U-R reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical values are -31 to 31 dBm). A value of 0x7FFFFFFF(2147483647) indicates the measurement is out of range to be represented. Unit: 0.1 dB |
| VDS vdsl2LineBandPlan | 1.3.6.1.4.1.2011.6.115.1.1.1.1.26 | Vdsl2BandPlan | read-only | Band contains a series of subcarriers. The first octet is the number of bands. Other octets describe the info of each band. Each band info is a pair of values occupying 4 octets with the following structure: First octets - serial number of band Second octets - Direction of band Third fourth octets - Start index of band Fifth sixth octets - End index of band Huawei defined. |
| VDS vdsl2LinePsdMaskClassSelection | 1.3.6.1.4.1.2011.6.115.1.1.1.1.27 | Vdsl2TIPsdClassMask | read-only | The sub class of VDSL2 PSD Mask. |
| VDS vdsl2LineCurrentVdsl2Profile | 1.3.6.1.4.1.2011.6.115.1.1.1.1.28 | Vdsl2SubProfiles | read-only | This configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line. |
| OCT vdsl2LineCnfgServiceProf | 1.3.6.1.4.1.2011.6.115.1.1.1.1.29 | OCTET STRING | read-write | The value of this object identifies the row in the VDSL2 Line Configuration Service Profile Table, (vdsl2ServProfTable), which applies for this VDSL2 line. |
| OCT vdsl2LineCnfgSpectrumProf | 1.3.6.1.4.1.2011.6.115.1.1.1.1.30 | OCTET STRING | read-write | The value of this object identifies the row in the VDSL2 Line Configuration Spectrum Profile Table, (vdsl2SpectrumProfTable), which applies for this VDSL2 line. |
| OCT vdsl2LineCnfgDpboProf | 1.3.6.1.4.1.2011.6.115.1.1.1.1.31 | OCTET STRING | read-write | The value of this object identifies the row in the VDSL2 Line Configuration Dpbo Profile Table, (vdsl2DpboProfTable), which applies for this VDSL2 line. |
| OCT vdsl2LineCnfgUpboProf | 1.3.6.1.4.1.2011.6.115.1.1.1.1.32 | OCTET STRING | read-write | The value of this object identifies the row in the VDSL2 Line Configuration Upbo Profile Table, (vdsl2UpboProfTable), which applies for this VDSL2 line. |
| OCT vdsl2LineCnfgNoiseMarginProf | 1.3.6.1.4.1.2011.6.115.1.1.1.1.33 | OCTET STRING | read-write | The value of this object identifies the row in the VDSL2 Line Configuration Noise Margin Profile Table, (vdsl2NoiseMarginProfTable), which applies for this VDSL2 line. |
| OCT vdsl2LineCnfgDelayINPProf | 1.3.6.1.4.1.2011.6.115.1.1.1.1.34 | OCTET STRING | read-write | The value of this object identifies the row in the VDSL2 Line Configuration Delay-INP Profile Table, (vdsl2DelayInpProfTable), which applies for this VDSL2 line. |
| U32 vdsl2UpboProfKl0CpeVal | 1.3.6.1.4.1.2011.6.115.1.1.1.1.35 | Unsigned32 | read-only | The actual value of KL0-CPE parameter,it ranges from 0 to 1280 units of 0.1 dB. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1dB |
| U32 vdsl2LineStatusCodingGainDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.36 | Unsigned32 | read-only | The actual value of Coding gain downstream parameter,it ranges from 0 to 16 units of 0.5 dB. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.5dB |
| U32 vdsl2LineStatusCodingGainUs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.37 | Unsigned32 | read-only | The actual value of Coding gain upstream parameter,it ranges from 0 to 16 units of 0.5 dB. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.5dB |
| U32 vdsl2LineStatusPcbDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.38 | Unsigned32 | read-only | The actual value of power cut back downstream parameter, it ranges from 0 to 40 units of 1 dB. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 1dB |
| OCT hwvdslDlmDsmprofile | 1.3.6.1.4.1.2011.6.115.1.1.1.1.39 | OCTET STRING | read-write | The value of this object identifies the row in the DLM/DSM Profile Table, which applies for this VDSL2 line. |
| VDS hwvdsl2LineActmode | 1.3.6.1.4.1.2011.6.115.1.1.1.1.40 | Vdsl2Actmode | read-only | Actived mode after training between co and cpe. Options: 1. ADSL(1) - ETSI,T1.413 G992.1,G992.2 2. ADSL2(2) - G992.3,G992.4 3. ADSL2PLUS(3) - G992.5 4. VDSL(4) - G993.1 5. VDSL2(5) - G993.2,G993.5 6. invalidValue(-1) - Invalid value |
| U32 vdsl2UpboProfKl0CoVal | 1.3.6.1.4.1.2011.6.115.1.1.1.1.41 | Unsigned32 | read-only | The actual value of KL0-CO parameter, it ranges from 0 to 1280 units of 0.1 dB. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1dB |
| VDS vdsl2LineStatusRtxUsedDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.42 | Vdsl2StatusRtxUsed | read-only | This parameter specifies whether G.998.4 retransmission is used in downstream. Options: 1. rtxInuse(1) - RTX in use 2. rtxUnusedModeForbidden(2) - RTX not in use, due to RTX-MODE = FORBIDDEN 3. rtxUnusedNotSupportedXtuc(3) - RTX not in use, due to not supported by the XTU-C 4. rtxUnusedNotSupportedXtur(4) - RTX not in use, due to not supported by the XTU-R 5. rtxUnusedNotSupportedXtucAndXtur(5) - RTX not in use, due to not supported by the XTU-C and XTU-R 6. invalidValue(-1) - Invalid value |
| VDS vdsl2LineStatusRtxUsedUs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.43 | Vdsl2StatusRtxUsed | read-only | This parameter specifies whether G.998.4 retransmission is used in upstream. Options: 1. rtxInuse(1) - RTX in use 2. rtxUnusedModeForbidden(2) - RTX not in use, due to RTX-MODE = FORBIDDEN 3. rtxUnusedNotSupportedXtuc(3) - RTX not in use, due to not supported by the XTU-C 4. rtxUnusedNotSupportedXtur(4) - RTX not in use, due to not supported by the XTU-R 5. rtxUnusedNotSupportedXtucAndXtur(5) - RTX not in use, due to not supported by the XTU-C and XTU-R 6. invalidValue(-1) - Invalid value |
| INT vdsl2LineStatusLastRetrainInfo | 1.3.6.1.4.1.2011.6.115.1.1.1.1.44 | INTEGER | read-only | Indicates the last retrained information performed on the line. Options: 1. none(1) - No record is available 2. cpe-l3-trigger(2) - The terminal initiates a low power consumption L3 request 3. lom-us-trigger-dra(3) - The upstream noise margin is smaller than the minimum noise margin in rate dynamic adjustment 4. lom-ds-trigger-dra(4) - The downstream noise margin is smaller than the minimum noise margin in rate dynamic adjustment 5. cpe-never-answer-oam(5) - No OAM response is received from the CPE all the time 6. cpe-no-more-answer-oam(6) - No OAM response is received from the CPE 7. persistent-ncd-us(7) - Upstream continuous no cell delineation 8. persistent-ncd-ds(8) - Downstream continuous no cell delineation 9. persistent-lcd-us(9) - Upstream continuous loss of cell delineation 10.persistent-lcd-ds(10) - Downstream continuous loss of cell delineation 11.l2-problem-co-drop(11) - The CO is faulty during the switching from L0 to L2 12.l2-problem-cpe-drop(12) - The CPE is faulty during the switching from L0 to L2 13.bitswap-refused-us-co-drop(13) - The CO goes offline when the upstream bit swap fault occurs 10 times consecutively 14.bitswap-refused-us-cpe-drop(14) - The CPE goes offline when the downstream bit swap fault occurs 10 times consecutively 15.channel-change-us-co-drop(15) - The CO goes offline when the upstream net rate changes 16.channel-change-us-cpe-drop(16) - The CPE goes offline when the upstream net rate changes 17.noise-increase-us-co-drop(17) - The CO goes offline when the upstream noise increases 18.noise-increase-us-cpe-drop(18) - The CPE goes offline when the upstream noise increases 19.bitswap-refused-ds-co-drop(19) - The CO goes offline when the downstream bit swap fault occurs 10 times consecutively 20.bitswap-refused-ds-cpe-drop(20) - The CPE goes offline when the downstream bit swap fault occurs 10 times consecutively 21.channel-change-ds-co-drop(21) - The CO goes offline when the downstream net rate changes 22.channel-change-ds-cpe-drop(22) - The CPE goes offline when the downstream net rate changes 23.noise-increase-ds-co-drop(23) - The CO goes offline when the downstream noise increases 24.noise-increase-ds-cpe-drop(24) - The CPE goes offline when the downstream noise increases 25.lom-us-co-drop(25) - The CO goes offline when the upstream noise margin is smaller than the minimum noise margin 26.lom-us-cpe-drop(26) - The CPE goes offline when the upstream noise margin is smaller than the minimum noise margin 27.lom-ds-co-drop(27) - The CO goes offline when the downstream noise margin is smaller than the minimum noise margin 28.lom-ds-cpe-drop(28) - The CPE goes offline when the downstream noise margin is smaller than the minimum noise margin 29.sra-problem-us-co-drop(29) - The CO goes offline when the upstream SRA is faulty 30.sra-problem-us-cpe-drop(30) - The CPE goes offline when the upstream SRA is faulty 31.sra-failed-us-co-drop(31) - The CO goes offline when the upstream SRA fails 32.sra-failed-us-cpe-drop(32) - The CPE goes offline when the upstream SRA fails 33.sra-problem-ds-co-drop(33) - The CO goes offline when the downstream SRA is fault 34.sra-problem-ds-cpe-drop(34) - The CPE goes offline when the downstream SRA is faulty 35.sra-rejected-ds-co-drop(35) - The CO goes offline when the downstream SRA is rejected 36.sra-rejected-ds-cpe-drop(36) - The CPE goes offline when the downstream SRA is rejected 37.bitswap-problem-us-co-drop(37) - The CO goes offline when the upstream bit swap is faulty 38.bitswap-problem-us-cpe-drop(38) - The CPE goes offline when the upstream bit swap is faulty 39.bitswap-failed-us-co-drop(39) - The CO goes offline when the upstream bit swap fails 40.bitswap-failed-us-cpe-drop(40) - The CPE goes offline when the upstream bit swap fails 41.bitswap-problem-ds-co-drop(41) - The CO goes offline when the downstream bit swap is faulty 42.bitswap-problem-ds-cpe-drop(42) - The CPE goes offline when the downstream bit swap is faulty 43.bitswap-rejected-ds-co-drop(43) - The CO goes offline when the downstream bit swap is rejected 44.bitswap-rejected-ds-cpe-drop(44) - The CPE goes offline when the downstream bit swap is rejected 45.cpe-switched-off(45) - The CPE power supply is shut down 46.cpe-lost(46) - The CPE is disconnected 47.co-reset(47) - The CO resets the chipset or line 48.co-stop(48) - The CO actively deactivate the port 49.unknown(49) - Unknown reason |
| I32 vdsl2UpboRxThreshDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.45 | Integer32 | read-only | This parameter reports the downstream received signal level threshold value used in the Alternative Electrical Length Estimation method (ELE-M1). This parameter represents an offset from -100 dB, and ranges from -64 dB to 0 dB in steps of 1 dB. The invalid value is 2147483647. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: dB |
| I32 vdsl2UpboRxThreshUs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.46 | Integer32 | read-only | This parameter reports the upstream received signal level threshold value used in the Alternative Electrical Length Estimation method (ELE-M1). This parameter represents an offset from -100 dB, and ranges from -64 dB to 0 dB in steps of 1 dB. The invalid value is 2147483647. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: dB |
| U32 hwvdsl2LineStatusLineRateDs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.47 | Unsigned32 | read-only | The actual line rate downstream. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: bits/second |
| U32 hwvdsl2LineStatusLineRateUs | 1.3.6.1.4.1.2011.6.115.1.1.1.1.48 | Unsigned32 | read-only | The actual line rate upstream. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: bits/second |
| INT hwvdsl2LineSplitterMode | 1.3.6.1.4.1.2011.6.115.1.1.1.1.49 | INTEGER | read-write | This parameter indicates which mode will be applied to the port splitter .The valid values for the splitter mode are 1 and 2. Options: 1. connect (1) - Splitter mode is connect 2. bypass (2) - Splitter mode is bypass |
| INT hwvdsl2LineBackup | 1.3.6.1.4.1.2011.6.115.1.1.1.1.50 | INTEGER | read-write | This parameter indicates whether the port backup is enabled. Options: 1. enable(1) - Enable the port backup. 2. disable(2) - Disable the port backup. |
| U32 hwvdsl2LineBackupPort | 1.3.6.1.4.1.2011.6.115.1.1.1.1.51 | Unsigned32 | read-only | This parameter indicates the backup port ifindex. If data on the port is invalid or no data is generated on the port, the port is not backed up. The invalid value is 4294967295. |
| INT hwvdsl2LinePhyRcontrol | 1.3.6.1.4.1.2011.6.115.1.1.1.1.52 | INTEGER | read-write | This parameter indicates whether the PHY-R retransmission is enabling. In TR165 mode, the H80BVDPM board should be enabled when it works as ADSL mode. Options: 1. enable(1) - Enable the PHY-R retransmission of VDSL2 line. 2. disable(2) - Disable the PHY-R retransmission of VDSL2 line. |
| vdsl2Status | 1.3.6.1.4.1.2011.6.115.1.2 | |||
| vdsl2ChannelStatusTable | 1.3.6.1.4.1.2011.6.115.1.2.1 | not-accessible | The table vdsl2ChannelStatusTable contains status parameters of VDSL2 channel. The indexes of this table are ifIndex and vdsl2ChStatusUnit. | |
| vdsl2ChannelStatusEntry | 1.3.6.1.4.1.2011.6.115.1.2.1.1 | not-accessible | The table vdsl2ChannelStatusTable contains status parameters of VDSL2 channel. The indexes of this entry are ifIndex and vdsl2ChStatusUnit. | |
| VDS vdsl2ChStatusUnit | 1.3.6.1.4.1.2011.6.115.1.2.1.1.1 | Vdsl2Unit | not-accessible | The termination unit xTU-C(1) or xTU-R(2). |
| U32 vdsl2ChStatusChannelNum | 1.3.6.1.4.1.2011.6.115.1.2.1.1.2 | Unsigned32 | read-only | Provides the bearer channel number associated with this row (i.e., the channel ifIndex). This enables determining the channel configuration profile and the channel thresholds profile applicable for this bearer channel. |
| U32 vdsl2ChStatusActDataRate | 1.3.6.1.4.1.2011.6.115.1.2.1.1.3 | Unsigned32 | read-only | If retransmission is not used in a given transmit direction, this parameter reports the actual net data rate at which the bearer channel is operating in L0 power management state, and in L1 or L2 states, the parameter contains the net data rate in the previous L0 state. If retransmission is used in a given transmit direction, this parameter reports the Expected Throughput(ETR) at which the bearer channel is operating in L0 power management state, and in L1 or L2 states, the parameter contains the Expected Throughput(ETR) in the previous L0 state. The data rate is coded in steps of 1000 bit/s. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: bits/second |
| U32 vdsl2ChStatusPrevDataRate | 1.3.6.1.4.1.2011.6.115.1.2.1.1.4 | Unsigned32 | read-only | If retransmission is not used in a given transmit direction, this parameter reports the previous net data rate the bearer channel was operating at just before the latest net data rate change event occurred, excluding all transitions between L0 state and L1 or L2 states. If retransmission is used in a given transmit direction, this parameter reports the previous Expected Throughput(ETR) (as defined in G.998.4) the bearer channel was operating at just before the latest ETR change event occurred, excluding all transitions between L0 state and L1 or L2 states. The data rate is coded in steps of 1000 bit/s. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: bits/second |
| U32 vdsl2ChStatusActDelay | 1.3.6.1.4.1.2011.6.115.1.2.1.1.5 | Unsigned32 | read-only | If retransmission is not used in a given transmit direction, this parameter is the actual one-way interleaving delay introduced by the PMS-TC excluding delay in L1 and L2 state. In L1 and L2 state, the parameter contains the interleaving delay in the previous L0 state. If retransmission is used in a given transmit direction, this parameter specifies the actual value of the time-independent component of the delay due to retransmission only. It is coded in ms (rounded to the nearest ms). The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: milliseconds |
| VDS vdsl2ChStatusAtmStatus | 1.3.6.1.4.1.2011.6.115.1.2.1.1.6 | Vdsl2ChAtmStatus | read-only | Indicates current state (existing failures) of the VDSL channel in case its Data Path is ATM. This is a bit-map of possible conditions. Options: 1. noDefect(0) - This bit position positively reports that no defect or failure exist 2. noCellDelineation(1) - The link was successfully initialized but cell delineation was never acquired on the associated ATM data path 3. lossOfCellDelineation(2) - Loss of cell delineation on the associated ATM data path In case the channel is not of ATM Data Path, the object is set to '0'. |
| VDS vdsl2ChStatusPtmStatus | 1.3.6.1.4.1.2011.6.115.1.2.1.1.7 | Vdsl2ChPtmStatus | read-only | Indicates current state (existing failures) of the VDSL channel in case its Data Path is PTM. This is a bit-map of possible conditions. Options: 1. noFailure(0) - No failure 2. outOfSync (1) - Out of synchronization In case the channel is not of PTM Data Path the object is set to '0'. |
| U32 vdsl2ChStatusINP | 1.3.6.1.4.1.2011.6.115.1.2.1.1.8 | Unsigned32 | read-only | If retransmission is not used in a given transmit direction, this parameter reports the actual impulse noise protection (INP) on the bearer channel in the L0 state. In the L1 or L2 state, the parameter contains the INP in the previous L0 state. If retransmission is used in a given transmit direction, this parameter reports the actual impulse noise protection (INP) against SHINE on the bearer channel in the L0 state. In the L2 state, the parameter contains the INP in the previous L0 state. The value is coded in fractions of DMT symbols with a granularity of 0.1 symbols. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.1 DMT symbol |
| U32 vdsl2ChStatusRSRedundancy | 1.3.6.1.4.1.2011.6.115.1.2.1.1.9 | Unsigned32 | read-only | The actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which the bearer channel is transported. The value is coded in bytes. The value 0 indicates no Reed-Solomon coding. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: byte |
| U32 vdsl2ChStatusRSSymbols | 1.3.6.1.4.1.2011.6.115.1.2.1.1.10 | Unsigned32 | read-only | The DMT Symbol number per codeword used in the latency path in which the bearer channel is transported. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: 0.01 DMT symbol |
| U32 vdsl2ChStatusInterDepth | 1.3.6.1.4.1.2011.6.115.1.2.1.1.11 | Unsigned32 | read-only | The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. The value ranges from 1 to 4096 by step of 1. The value 1 indicates no interleaving. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. |
| U32 vdsl2ChStatusSymbolLength | 1.3.6.1.4.1.2011.6.115.1.2.1.1.12 | Unsigned32 | read-only | The actual number of bits per symbol assigned to the latency path in which the bearer channel is transported. This value does not include trellis overhead. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: bit |
| U32 vdsl2ChStatusRSSize | 1.3.6.1.4.1.2011.6.115.1.2.1.1.13 | Unsigned32 | read-only | The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: byte |
| U32 vdsl2ChStatusInterBlockLength | 1.3.6.1.4.1.2011.6.115.1.2.1.1.14 | Unsigned32 | read-only | The actual block length of the interleaver used in the latency path in which the bearer channel is transported. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. Unit: byte |
| U32 vdsl2ChStatusLPATH | 1.3.6.1.4.1.2011.6.115.1.2.1.1.15 | Unsigned32 | read-only | The index of the actual latency path in which the bearer is transported. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, the invalid value will be returned. |
| U32 vdsl2ChStatusPhyRrrcBits | 1.3.6.1.4.1.2011.6.115.1.2.1.1.16 | Unsigned32 | read-only | The bits in the channel that used to retransmission. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. |
| U32 vdsl2ChStatusPhyRtxQueue | 1.3.6.1.4.1.2011.6.115.1.2.1.1.17 | Unsigned32 | read-only | Queues in send buffer used for retransmission. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. |
| U32 vdsl2ChStatusActNetDataRate | 1.3.6.1.4.1.2011.6.115.1.2.1.1.18 | Unsigned32 | read-only | In L0 state, this parameter reports the Net Data Rate at which the bearer channel is operating. In L2 state, this parameter contains the Net Data Rate in the previous L0 state. This parameter is optional if G.998.4 retransmission function is not supported. The data rate is coded in steps of 1000 bit/s. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. |
| U32 vdsl2ChStatusActINPAgainstREIN | 1.3.6.1.4.1.2011.6.115.1.2.1.1.19 | Unsigned32 | read-only | If retransmission is used in a given transmit direction, this parameter reports the actual impulse noise protection (INP) against REIN (under specific conditions detailed in G.998.4) on the bearer channel in the L0 state. In the L2 state, the parameter contains the INP in the previous L0 state. The value is coded in fractions of DMT symbols with a granularity of 0.1 symbols. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the invalid value will be returned. |
| U32 hwvdsl2ChStatusUnlimitedVersionEtru | 1.3.6.1.4.1.2011.6.115.1.2.1.1.20 | Unsigned32 | read-only | The unlimited version of expected throughput in kbit/s:(1 - RTxOH) * NDR. This value is specified in G.998.4 (G.INP). |
| vdsl2PrivSCStatusTable | 1.3.6.1.4.1.2011.6.115.1.2.2 | not-accessible | The table vdsl2PrivSCStatusTable contains status parameters of VDSL2 sub-carriers. The indexes of this table are ifIndex and vdsl2PrivSCStatusDirection. | |
| vdsl2PrivSCStatusEntry | 1.3.6.1.4.1.2011.6.115.1.2.2.1 | not-accessible | The table vdsl2PrivSCStatusTable contains status parameters of VDSL2 sub-carriers. The indexes of this entry are ifIndex and vdsl2PrivSCStatusDirection. | |
| VDS vdsl2PrivSCStatusDirection | 1.3.6.1.4.1.2011.6.115.1.2.2.1.1 | Vdsl2Direction | not-accessible | The direction of the sub-carrier either upstream or downstream. |
| U32 vdsl2PrivSCStatusMtime | 1.3.6.1.4.1.2011.6.115.1.2.2.1.2 | Unsigned32 | read-only | SNR Measurement Time. The number of symbols used to measure the SNR values on the respective transmission direction. It should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated otherwise. Unit: symbols |
| OCT vdsl2PrivSCStatusSnr | 1.3.6.1.4.1.2011.6.115.1.2.2.1.3 | OCTET STRING | read-only | The SNR Margin per sub-carrier, expressing the ratio between the received signal power and received noise power per subscriber. It is an array of 4096 bytes, designed for supporting up to 4096 sub-carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Byte i (0 <= i < NSC) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream sub- carrier i has SNR of: (-32 + Vdsl2SubcarrierSnr(i)/2) in dB (i.e., -32 to 95dB). The special value 255 means that no measurement could be done for the subcarrier because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide. |
| OCT vdsl2PrivSCStatusBitsAlloc | 1.3.6.1.4.1.2011.6.115.1.2.2.1.4 | OCTET STRING | read-only | The bits allocation per sub-carrier. An array of 2048 bytes, designed for supporting up to 4096 sub-carriers. The number of utilized nibbles on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Nibble i (0 <= i < NSC) is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream sub-carrier i has the same amount of bits allocation. Unit: bits |
| OCT vdsl2PrivSCStatusGainAlloc | 1.3.6.1.4.1.2011.6.115.1.2.2.1.5 | OCTET STRING | read-only | The gain allocation per sub-carrier. An array of 8192 bytes, designed for supporting up to 4096 sub-carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred here as NSC. Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate that the respective downstream or upstream sub-carrier i has the same amount of gain value. The gain value is represented as a multiple of 1/512 on linear scale. Each value in this array is 16 bits wide and is stored in big endian format. |
| vdsl2SCStatusTable | 1.3.6.1.4.1.2011.6.115.1.2.3 | not-accessible | The table vdsl2SCStatusTable contains sub-carrier status parameters for VDSL2/ADSL/ADSL2 and ADSL2+ that DO NOT refer to specific sub-carriers. In addition, the table contains parameters that provide information about the size of parameters in vdsl2SCStatusSegmentTable. This table contains live data from equipment. The indexes of this table are ifIndex and vdsl2SCStatusDirection. | |
| vdsl2SCStatusEntry | 1.3.6.1.4.1.2011.6.115.1.2.3.1 | not-accessible | The table vdsl2SCStatusTable contains sub-carrier status parameters for VDSL2/ADSL/ADSL2 and ADSL2+ that DO NOT refer to specific sub-carriers. In addition, the table contains parameters that provide information about the size of parameters in vdsl2SCStatusSegmentTable. This table contains live data from equipment. The indexes of this entry are ifIndex and vdsl2SCStatusDirection. | |
| VDS vdsl2SCStatusDirection | 1.3.6.1.4.1.2011.6.115.1.2.3.1.1 | Vdsl2Direction | not-accessible | The direction of the sub-carrier either upstream or downstream |
| U32 vdsl2SCStatusLinScale | 1.3.6.1.4.1.2011.6.115.1.2.3.1.2 | Unsigned32 | read-only | The scale factor to be applied to the H(f) linear representation values for the respective transmission direction. This parameter is only available after a loop diagnostic procedure. |
| U32 vdsl2SCStatusLinScGroupSize | 1.3.6.1.4.1.2011.6.115.1.2.3.1.3 | Unsigned32 | read-only | Number of sub-carriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is equal to the size of a sub-carrier group used to compute these parameters. This parameter is only available after a loop diagnostic procedure. |
| U32 vdsl2SCStatusLogMt | 1.3.6.1.4.1.2011.6.115.1.2.3.1.4 | Unsigned32 | read-only | The number of symbols used to measure the H(f) logarithmic measurement values for the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated in initialization. |
| U32 vdsl2SCStatusLogScGroupSize | 1.3.6.1.4.1.2011.6.115.1.2.3.1.5 | Unsigned32 | read-only | Number of sub-carriers per group used to report the H(f) logarithmic representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is equal to the size of a sub-carrier group used to compute these parameters. This parameter is only available after a loop diagnostic procedure. |
| U32 vdsl2SCStatusQlnMt | 1.3.6.1.4.1.2011.6.115.1.2.3.1.6 | Unsigned32 | read-only | The number of symbols used to measure the Quiet Line Noise values on the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated in initialization. |
| U32 vdsl2SCStatusQlnScGroupSize | 1.3.6.1.4.1.2011.6.115.1.2.3.1.7 | Unsigned32 | read-only | Number of sub-carriers per group used to report the Quiet Line Noise values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is equal to the size of a sub-carrier group used to compute these parameters. This parameter is only available after a loop diagnostic procedure. |
| U32 vdsl2SCStatusMtime | 1.3.6.1.4.1.2011.6.115.1.2.3.1.8 | Unsigned32 | read-only | SNR Measurement Time. The number of symbols used to measure the SNR values on the respective transmission direction. It should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated otherwise. Unit: symbols |
| U32 vdsl2SCStatusSnrScGroupSize | 1.3.6.1.4.1.2011.6.115.1.2.3.1.9 | Unsigned32 | read-only | Number of sub-carriers per group used to report the SNR values on the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is equal to the size of a sub-carrier group used to compute these parameters. This parameter is only available after a loop diagnostic procedure. |
| U32 vdsl2SCStatusAttainableRate | 1.3.6.1.4.1.2011.6.115.1.2.3.1.10 | Unsigned32 | read-only | Maximum Attainable Data Rate. The maximum net data rate currently attainable by the XTU-C transmitter and XTU-R receiver (when referring to downstream direction) or by the XTU-R transmitter and XTU-C receiver (when referring to upstream direction). Value is coded in bits/s. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated. Unit: bits/second |
| I32 vdsl2SCStatusActAtp | 1.3.6.1.4.1.2011.6.115.1.2.3.1.11 | Integer32 | read-only | Actual Aggregate Transmit Power from the XTU (XTU-R on downstream direction and XTU-C on upstream direction), at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical values are -31 to 31 dBm). A value of all 1's indicates the measurement is out of range to be represented. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated. Unit: 0.1 dB |
| ROW vdsl2SCStatusRowStatus | 1.3.6.1.4.1.2011.6.115.1.2.3.1.12 | RowStatus | read-write | Row Status. The SNMP agent should create rows in this table and in the vdsl2SCStatusTable for storing the results of a DELT performed on the associated line, if such rows do not already exist. The SNMP agent may have limited resources; therefore, if multiple rows co-exist in the table, it may fail to add new rows to the two tables or allocate memory resources for a new DELT process. If that occurs, the SNMP agent responds with either the value 'tableFull' or the value 'noResources' (for xdsl2LineCmndConfLdsfFailReason object in xdsl2LineTable) The management system (the operator) may delete rows according to any scheme. E.g., after retrieving the results. |
| VDS vdsl2SCStatusProfile | 1.3.6.1.4.1.2011.6.115.1.2.3.1.13 | Vdsl2Profiles | read-only | This configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line. |
| VDS vdsl2SCStatusClassmask | 1.3.6.1.4.1.2011.6.115.1.2.3.1.14 | Vdsl2PSDClassMask | read-only | In order to reduce the number of configuration possibilities, the limit PSD masks are grouped in the following PSD mask classes: - Class 998 Annex A: D-32, D-64. - Class 997-M1c Annex B: 997-M1c-A-7. - Class 997-M1x Annex B: 997-M1x-M-8, 997-M1x-M. - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M. - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0. - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0. - Class HPE17 Annex B: HPE17-M1-NUS0. - Class HPE30 Annex B: HPE30-M1-NUS0. - Class 997E17-M2x Annex B: 997E17-M2x-NUS0. - Class 997E30-M2x Annex B: 997E30-M2x-NUS0. - Class 998E17-M2x Annex B: 998E17-M2x-NUS0, 998E17-M2x-NUS0-M, 998E17-M2x-A. - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B. - Class 998E30-M2x Annex B: 998E30-M2x-NUS0, 998E30-M2x-NUS0-M. - Class 998ADE30-M2x Annex B: 998ADE30-M2x-NUS0-M, 998ADE30-M2x-NUS0-A. |
| vdsl2SCStatusBandTable | 1.3.6.1.4.1.2011.6.115.1.2.4 | not-accessible | The table vdsl2SCStatusBandTable contains sub-carrier status parameters for VDSL2/ADSL/ADSL2 and ADSL2+ that are grouped per-band. For ADSL/ADSL2/ADSL2+, there is a single upstream band and a single downstream band. For VDSL2, there are several downstream bands and several upstream bands. The indexes of this table are ifIndex and vdsl2SCStatusBand. | |
| vdsl2SCStatusBandEntry | 1.3.6.1.4.1.2011.6.115.1.2.4.1 | not-accessible | The table vdsl2SCStatusBandTable contains sub-carrier status parameters for VDSL2/ADSL/ADSL2 and ADSL2+ that are grouped per-band. For ADSL/ADSL2/ADSL2+, there is a single upstream band and a single downstream band. For VDSL2, there are several downstream bands and several upstream bands. The indexes of this entry are ifIndex and vdsl2SCStatusBand. | |
| XDS vdsl2SCStatusBand | 1.3.6.1.4.1.2011.6.115.1.2.4.1.1 | Xdsl2Band | not-accessible | The transmission band. Identifies a band in a VDSL2/ADSL/ADSL2/ADSL2+ link. For a band in the upstream direction, transmission is from the remote end (xTU-R) towards the central office end (xTU-C). A band in the upstream direction is indicated by upstream(1) for ADSL/ADSL2/ADSL2+ single band, or any of us0(3), us1(5), us2(7), us3(9), or us4(11) for VDSL2 multiple bands. For a band in the downstream direction, transmission is from the xTU-C towards the xTU-R. A band in the downstream direction is indicated by downstream(2) for ADSL/ADSL2/ADSL2+ single band, or any of ds1(4), ds2(6), ds3(8), or ds4(10) for VDSL2 multiple bands. |
| U32 vdsl2SCStatusBandLnAtten | 1.3.6.1.4.1.2011.6.115.1.2.4.1.2 | Unsigned32 | read-only | When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all sub-carriers during diagnostics mode. When referring to a band in the upstream direction, it is the measured difference in the total power transmitted by the xTU-R and the total power received by the xTU-C over all sub-carriers during diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated. Unit: 0.1 dB |
| U32 vdsl2SCStatusBandSigAtten | 1.3.6.1.4.1.2011.6.115.1.2.4.1.3 | Unsigned32 | read-only | When referring to a band the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all sub carriers during Showtime after the diagnostics mode. When referring to the upstream direction, it is the measured difference in the total power transmitted by the xTU-R and the total power received by the xTU-C over all sub carriers during Showtime after the diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated. Unit: 0.1 dB |
| I32 vdsl2SCStatusBandSnrMargin | 1.3.6.1.4.1.2011.6.115.1.2.4.1.4 | Integer32 | read-only | SNR Margin is the maximum increase in dB of the noise power received at the XTU (xTU-R on downstream direction and xTU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the XTU. It ranges from -640 to 630 units of 0.1 dB (Physical values are -64 to 63 dB). A special value of 0x7FFFFFFF (2147483647) indicates the SNR Margin is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the SNR Margin measurement is currently unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated. Unit: 0.1 dB |
| U32 vdsl2SCStatusBandUpbokle | 1.3.6.1.4.1.2011.6.115.1.2.4.1.5 | Unsigned32 | read-only | This parameter is a vector of UPBO electrical length per-band estimates for each supported upstream/downstream band, expressed in dB at 1 MHz (kl0) calculated by the VTU-O/VTU-R, based on separate measurements in the supported upstream bands excluding US0/downstream bands. The value ranges from 0 to 128 dB in steps of 0.1 dB, with special value 204.7 which indicates that the estimate is greater than 128 dB. This parameter is required for the Alternative Electrical Length Estimation method (ELE-M1). Unit: 0.1 dB |
| vdsl2SCStatusSegmentTable | 1.3.6.1.4.1.2011.6.115.1.2.5 | not-accessible | The table vdsl2SCStatusSegmentTable contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ sub-carriers. Several objects in the table refer to NSus and NSds. For G.993.2, the value of NSus and NSds are respectively the indices of the highest supported upstream and downstream subcarriers according to the selected implementation profile. For ADSL, NSus is equal to NSCus-1 and NSds is equal to NSCds-1. The indexes of this table are ifIndex, vdsl2SCStatusDirection, and vdsl2SCStatusSegment. One index of this entry is an interface index where the interface has an ifType of vdsl2(251). The second index of this entry is the transmission direction. The third index identifies the specific segment of the sub-carriers status addressed. | |
| vdsl2SCStatusSegmentEntry | 1.3.6.1.4.1.2011.6.115.1.2.5.1 | not-accessible | The table vdsl2SCStatusSegmentTable contains status parameters of VDSL2/ADSL/ADSL2 and ADSL2+ sub-carriers. Several objects in the table refer to NSus and NSds. For G.993.2, the value of NSus and NSds are respectively the indices of the highest supported upstream and downstream subcarriers according to the selected implementation profile. For ADSL, NSus is equal to NSCus-1 and NSds is equal to NSCds-1. The indexes of this entry are ifIndex, vdsl2SCStatusDirection, and vdsl2SCStatusSegment. One index of this entry is an interface index where the interface has an ifType of vdsl2(251). The second index of this entry is the transmission direction. The third index identifies the specific segment of the sub-carriers status addressed. | |
| U32 vdsl2SCStatusSegment | 1.3.6.1.4.1.2011.6.115.1.2.5.1.1 | Unsigned32 | not-accessible | The segment of the sub-carriers status information provided by this row. Several status parameters in this table are retrieved in segments. The first segment of the status information is retrieved with vdsl2SCStatusSegment=1, the second segment is retrieved with vdsl2SCStatusSegment=2, and so on. When any status parameter is retrieved in n segments where n<8) then, for that parameter, GET operations for the rest segment numbers (n+1 to 8) are responded with a value that indicates: No measurement could be done. |
| OCT vdsl2SCStatusSegmentLinReal | 1.3.6.1.4.1.2011.6.115.1.2.5.1.2 | OCTET STRING | read-only | An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers groups and can be retrieved in a single segment. The number of utilized values on downstream direction depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. Each array entry represents the real component [referred here as a(i)] of Hlin(f = i*Df) value for a particular sub-carrier group index i (0 <= i < NS). Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is vdsl2SCStatusLinScale and a(i) and b(i) [provided by the vdsl2SCStatusSegmentLinImg object] are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the sub-carriers group because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format. |
| OCT vdsl2SCStatusSegmentLinImg | 1.3.6.1.4.1.2011.6.115.1.2.5.1.3 | OCTET STRING | read-only | An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers groups and can be retrieved in a single segment. The number of utilized values on downstream direction depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. Each array entry represents the imaginary component [referred here as b(i)] of Hlin(f = i*Df) value for a particular sub- carrier group index i (0 <= i < NS). Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is vdsl2SCStatusLinScale and a(i) [provided by the vdsl2SCStatusSegmentLinReal object] and b(i) are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the sub-carriers group because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format. |
| OCT vdsl2SCStatusSegmentLog | 1.3.6.1.4.1.2011.6.115.1.2.5.1.4 | OCTET STRING | read-only | An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers groups and can be retrieved in a single segment. The number of utilized values on downstream direction depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. Each array entry represents the real Hlog(f = i*Df) value for a particular sub-carrier group index i, (0 <= i < NS). The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022. A special value m=1023 indicates that no measurement could be done for the sub-carrier group because it is out of the passband or that the attenuation is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 16 bits wide and is stored in big endian format. Unit: dB |
| OCT vdsl2SCStatusSegmentQln | 1.3.6.1.4.1.2011.6.115.1.2.5.1.5 | OCTET STRING | read-only | An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers groups and can be retrieved in a single segment. The number of utilized values on downstream direction depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. Each array entry represents the QLN(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NS). The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the sub-carrier group because it is out of the passband or that the noise PSD is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 8 bits wide. Unit: dBm/Hz |
| OCT vdsl2SCStatusSegmentSnr | 1.3.6.1.4.1.2011.6.115.1.2.5.1.6 | OCTET STRING | read-only | The SNR Margin per sub-carrier group, expressing the ratio between the received signal power and received noise power per sub-scriber group. It is an array of 512 octets, designed for supporting up to 512 (downstream) sub-carriers groups and can be retrieved in a single segment. The number of utilized octets on downstream direction depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. Octet i (0 <= i < NS) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream sub- carrier group i has SNR of: (-32 + xdsl2SCStatusSegmentSnr(i)/2) in dB (i.e., -32 to 95dB). The special value 255 means that no measurement could be done for the sub-carrier group because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide. Unit: 0.5 dB |
| OCT vdsl2SCStatusSegmentBitsAlloc | 1.3.6.1.4.1.2011.6.115.1.2.5.1.7 | OCTET STRING | read-only | The bits allocation per sub-carrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. When more then 512 sub-carriers are supported, the status information is reported through multiple (up to 8) segments. The first segment is then used for the first 512 sub-carriers. The second segment is used for the sub-carriers 512 to 1023 and so on. The aggregate number of utilized nibbles on downstream direction (in all segments) depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. The segment number is in xdsl2SCStatusSegment. Nibble i (0 <= i < MIN(NS-(segment-1)*512,512)) in each segment is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream sub-carrier j (j=(segement-1)*512+i) has the same amount of bits allocation. Unit: bits |
| OCT vdsl2SCStatusSegmentGainAlloc | 1.3.6.1.4.1.2011.6.115.1.2.5.1.8 | OCTET STRING | read-only | The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. When more then 512 sub-carriers are supported, the status information is reported through multiple (up to 8) segments. The first segment is then used for the first 512 sub-carriers. The second segment is used for the sub-carriers 512 to 1023 and so on. The aggregate number of utilized octets on downstream direction depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. The segment number is in xdsl2SCStatusSegment. Value i (0 <= i < MIN(NS-(segment-1)*512,512)) in each segment is set to a value in the range 0 to 4093 to indicate that the respective downstream or upstream sub-carrier j (j=(segement-1)*512+i) has the same amount of gain value. The gain value is represented as a multiple of 1/512 on linear scale. Each value in this array is 16 bits wide and is stored in big endian format. |
| VDS vdsl2SCStatusSegmentTssi | 1.3.6.1.4.1.2011.6.115.1.2.5.1.9 | Vdsl2Tssi | read-only | The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1. Each breakpoint is a pair of values occupying 3 octets with the following structure: First 2 octets - Index of the subcarrier used in the context of the breakpoint. Third octet - The shaping parameter at the breakpoint. Subcarrier index is an unsigned number in the range 1 to either NSCds (downstream direction) or NSCus (upstream direction). The shaping parameter value is in the range 0 to 127 (units of -0.5dB). The special value 127 indicates that the subcarrier is not transmitted. |
| OCT vdsl2SCStatusSegmentTxPSD | 1.3.6.1.4.1.2011.6.115.1.2.5.1.65535 | OCTET STRING | read-only | The TxPSD per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. When more then 512 sub-carriers are supported, the status information is reported through multiple (up to 8) segments. The first segment is then used for the first 512 sub-carriers. The second segment is used for the sub-carriers 512 to 1023 and so on. |
| OCT vdsl2SCStatusSegmentSnrMargin | 1.3.6.1.4.1.2011.6.115.1.2.5.1.65536 | OCTET STRING | read-only | The SnrMargin per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. When more then 512 sub-carriers are supported, the status information is reported through multiple (up to 8) segments. The first segment is then used for the first 512 sub-carriers. The second segment is used for the sub-carriers 512 to 1023 and so on. |
| U32 vdsl2SCStatusSegmentLogScGroupSize | 1.3.6.1.4.1.2011.6.115.1.2.5.1.65537 | Unsigned32 | read-only | Number of sub-carriers per group used to report the H(f) logarithmic representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is equal to the size of a sub-carrier group used to compute these parameters. This parameter is only available after a loop diagnostic procedure. It's available for the first segment, other segments return '-1'. |
| U32 vdsl2SCStatusSegmentQlnScGroupSize | 1.3.6.1.4.1.2011.6.115.1.2.5.1.65538 | Unsigned32 | read-only | Number of sub-carriers per group used to report the Quiet Line Noise values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is equal to the size of a sub-carrier group used to compute these parameters. This parameter is only available after a loop diagnostic procedure. It's available for the first segment, other segments return '-1'. |
| U32 vdsl2SCStatusSegmentLinScGroupSize | 1.3.6.1.4.1.2011.6.115.1.2.5.1.65539 | Unsigned32 | read-only | Number of sub-carriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is equal to the size of a sub-carrier group used to compute these parameters. This parameter is only available after a loop diagnostic procedure. It's available for the first segment, other segments return '-1'. |
| U32 vdsl2SCStatusSegmentSnrScGroupSize | 1.3.6.1.4.1.2011.6.115.1.2.5.1.65540 | Unsigned32 | read-only | Number of sub-carriers per group used to report the SNR values on the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is equal to the size of a sub-carrier group used to compute these parameters. This parameter is only available after a loop diagnostic procedure. It's available for the first segment, other segments return '-1'. |
| OCT hwvdsl2SCStatusSegmentQlnWithVectoring | 1.3.6.1.4.1.2011.6.115.1.2.5.1.65541 | OCTET STRING | read-only | An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers groups and can be retrieved in a single segment. The number of utilized values on downstream direction depends on NSds, and on upstream direction it depends on NSus. This value is referred here as NS. Each array entry represents the QLN(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NS). The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the sub-carrier group because it is out of the passband or that the noise PSD is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 8 bits wide. Unit: dBm/Hz This value is calculated with vectoring effect. |
| hwVdslSCFextTable | 1.3.6.1.4.1.2011.6.115.1.2.6 | not-accessible | The table hwVdslSCFextTable contains FEXT coupling function parameters. The indexes of this table are ifIndex, hwVdslSCFextFromIfindex, and hwVdslSCFextRequestXLinScGroupSize. | |
| hwVdslSCFextEntry | 1.3.6.1.4.1.2011.6.115.1.2.6.1 | not-accessible | The table hwVdslSCFextTable contains FEXT coupling function parameters. The indexes of this entry are ifIndex, hwVdslSCFextFromIfindex, and hwVdslSCFextRequestXLinScGroupSize. | |
| I32 hwVdslSCFextFromIfindex | 1.3.6.1.4.1.2011.6.115.1.2.6.1.1 | Integer32 | not-accessible | The hwVdslSCFextFromIfindex is an interface index where the interface has an ifType of vdsl2(251). |
| U32 hwVdslSCFextRequestXLinScGroupSize | 1.3.6.1.4.1.2011.6.115.1.2.6.1.2 | Unsigned32 | not-accessible | This parameter is the requested value of XLING. The valid values are 1, 2, 4, 8, 16, 32, and 64. |
| U32 hwVdslSCFextXLinScaleDs | 1.3.6.1.4.1.2011.6.115.1.2.6.1.3 | Unsigned32 | read-only | This parameter is the scale factor to be applied to the downstream Xlinpsds values. It is represented as an unsigned integer in the range from 1 to 2^16 - 1. |
| U32 hwVdslSCFextXlinScGroupSizeDs | 1.3.6.1.4.1.2011.6.115.1.2.6.1.4 | Unsigned32 | read-only | This parameter is the number of subcarriers per group used to report Xlinpsds. The valid values are 1, 2, 4, 8, 16, 32, and 64. XLINGds should equal the sub-sampling factor used to estimate the crosstalk channel for cancellation. |
| OCT hwVdslSCFextXLinBandDs | 1.3.6.1.4.1.2011.6.115.1.2.6.1.5 | OCTET STRING | read-only | XLINBANDSds contains pairs of (start-subcarrier-index, stop-subcarrier-index) for every band in which XLINpsds is reported. |
| OCT hwVdslSCFextXlinRealDs | 1.3.6.1.4.1.2011.6.115.1.2.6.1.6 | OCTET STRING | read-only | For each given VCE port index k, this parameter is a one-dimensional array of complex values in linear scale for downstream FEXT coupling coefficients Xlinds(f) originating from the loop connected to the VCE port k into the loop for which Xlinds(f) is being reported. Each array entry represents the Xlinds(f = n*Df) value for a particular subcarrier index n. The Xlinds(f = n*Df) value is represented as ((XLINSCds/2^15) * ((a(n) + j*b(n))/2^15)), where a(n) and b(n) are signed integers in the (-2^15 + 1) to (+2^15 - 1) range. A special value indicates that no measurement could be done from line k into this line for subcarrier n. Another special value indicates that there is no phase information and the magnitude of Xlinds (f = n*Df) is ((XLINSCds/2^15) * (a(n)/2^15)). |
| OCT hwVdslSCFextXlinImgDs | 1.3.6.1.4.1.2011.6.115.1.2.6.1.7 | OCTET STRING | read-only | For each given VCE port index k, this parameter is a one-dimensional array of complex values in linear scale for downstream FEXT coupling coefficients Xlinds(f) originating from the loop connected to the VCE port k into the loop for which Xlinds(f) is being reported. Each array entry represents the Xlinds(f = n*Df) value for a particular subcarrier index n. The Xlinds(f = n*Df) value is represented as ((XLINSCds/2^15) * ((a(n) + j*b(n))/2^15)), where a(n) and b(n) are signed integers in the (-2^15 + 1) to (+2^15 - 1) range. A special value indicates that no measurement could be done from line k into this line for subcarrier n. Another special value indicates that there is no phase information and the magnitude of Xlinds (f = n*Df) is ((XLINSCds/2^15) * (a(n)/2^15)). |
| U32 hwVdslSCFextXLinScaleUs | 1.3.6.1.4.1.2011.6.115.1.2.6.1.8 | Unsigned32 | read-only | This parameter is the scale factor to be applied to the upstream Xlinpsus values. It is represented as an unsigned integer in the range from 1 to 2^16 - 1. |
| U32 hwVdslSCFextXlinScGroupSizeUs | 1.3.6.1.4.1.2011.6.115.1.2.6.1.9 | Unsigned32 | read-only | This parameter is the number of subcarriers per group used to report Xlinpsus. The valid values are 1, 2, 4, 8, 16, 32, and 64. XLINGus should equal the sub-sampling factor used to estimate the crosstalk channel for cancellation. |
| OCT hwVdslSCFextXLinBandUs | 1.3.6.1.4.1.2011.6.115.1.2.6.1.10 | OCTET STRING | read-only | XLINBANDSus contains pairs of (start-subcarrier-index, stop-subcarrier-index) for every band in which XLINpsus is reported. |
| OCT hwVdslSCFextXlinRealUs | 1.3.6.1.4.1.2011.6.115.1.2.6.1.11 | OCTET STRING | read-only | For each given VCE port index k, this parameter is a one-dimensional array of complex values in linear scale for upstream FEXT coupling coefficients Xlinus(f) originating from the loop connected to the VCE port k into the loop for which Xlinus(f) is being reported. Each array entry represents the Xlinus(f = n*Df) value for a particular subcarrier index n. The Xlinus(f = n*Df) value is represented as ((XLINSCus/2^15) * ((a(n) + j*b(n))/2^15)), where a(n) and b(n) are signed integers in the (-2^15 + 1) to (+2^15 - 1) range. A special value indicates that no measurement could be done from line k into this line for subcarrier n. Another special value indicates that there is no phase information and the magnitude of Xlinus (f = n*Df) is ((XLINSCus/2^15) * (a(n)/2^15)). |
| OCT hwVdslSCFextXlinImgUs | 1.3.6.1.4.1.2011.6.115.1.2.6.1.12 | OCTET STRING | read-only | For each given VCE port index k, this parameter is a one-dimensional array of complex values in linear scale for upstream FEXT coupling coefficients Xlinus(f) originating from the loop connected to the VCE port k into the loop for which Xlinus(f) is being reported. Each array entry represents the Xlinus(f = n*Df) value for a particular subcarrier index n. The Xlinus(f = n*Df) value is represented as ((XLINSCus/2^15) * ((a(n) + j*b(n))/2^15)), where a(n) and b(n) are signed integers in the (-2^15 + 1) to (+2^15 - 1) range. A special value indicates that no measurement could be done from line k into this line for subcarrier n. Another special value indicates that there is no phase information and the magnitude of Xlinus (f = n*Df) is ((XLINSCus/2^15) * (a(n)/2^15)). |
| vdsl2Inventory | 1.3.6.1.4.1.2011.6.115.1.3 | |||
| vdsl2LineInventoryTable | 1.3.6.1.4.1.2011.6.115.1.3.1 | not-accessible | The table vdsl2LineInventoryTable contains inventory of VDSL2 unit. The indexes of this table are ifIndex and vdsl2LInvUnit. | |
| vdsl2LineInventoryEntry | 1.3.6.1.4.1.2011.6.115.1.3.1.1 | not-accessible | The table vdsl2LineInventoryTable contains inventory of VDSL2 unit. The indexes of this entry are ifIndex and vdsl2LInvUnit. | |
| VDS vdsl2LInvUnit | 1.3.6.1.4.1.2011.6.115.1.3.1.1.1 | Vdsl2Unit | not-accessible | The termination unit XTUC{1} or XTUR{2}. |
| OCT vdsl2LInvG994VendorId | 1.3.6.1.4.1.2011.6.115.1.3.1.1.2 | OCTET STRING | read-only | The xTU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR message. It consists of 8 binary octets, including a country code followed by a (regionally allocated) provider code, as defined in Recommendation T.35. |
| OCT vdsl2LInvSystemVendorId | 1.3.6.1.4.1.2011.6.115.1.3.1.1.3 | OCTET STRING | read-only | The xTU System Vendor ID (identifies the xTU system integrator) as inserted in the Overhead Messages (both xTUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only xTU-R in G.992.1 and G.992.2). It consists of 8 binary octets, with same format as used for Vdsl2InvG994VendorId. |
| OCT vdsl2LInvVersionNumber | 1.3.6.1.4.1.2011.6.115.1.3.1.1.4 | OCTET STRING | read-only | The xTU version number (vendor specific information) as inserted in the Overhead Messages (both xTUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only xTU-R in G.992.1 and G.992.2). It consists of up to 16 binary octets. |
| OCT vdsl2LInvSerialNumber | 1.3.6.1.4.1.2011.6.115.1.3.1.1.5 | OCTET STRING | read-only | The xTU serial number (vendor specific information) as inserted in the Overhead Messages (both xTUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only xTU-R in G.992.1 and G.992.2). It is vendor specific information. It consists of up to 32 ASCII characters. |
| OCT vdsl2LInvSelfTestResult | 1.3.6.1.4.1.2011.6.115.1.3.1.1.6 | OCTET STRING | read-only | The xTU self-test result, coded as a 32-bit integer. The most significant octet of this object is '0' if the self-test passed, and '1' if the self-test failed. The interpretation of the other octets is vendor discretionary. |
| VDS vdsl2LInvTransmissionCapabilities | 1.3.6.1.4.1.2011.6.115.1.3.1.1.7 | Vdsl2TransmissionModeType | read-only | The xTU transmission system capability list of the different coding types. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the xTU supports the respective coding. The value may be derived from the handshaking procedures defined in G.994.1. A set of VDSL2 line transmission modes, with one bit per mode. |
| OCT vdsl2LInvModelId | 1.3.6.1.4.1.2011.6.115.1.3.1.1.8 | OCTET STRING | read-only | The XTU model ID. |
| vdsl2PM | 1.3.6.1.4.1.2011.6.115.1.4 | |||
| vdsl2PMLine | 1.3.6.1.4.1.2011.6.115.1.4.1 | |||
| vdsl2PMLineCurrTable | 1.3.6.1.4.1.2011.6.115.1.4.1.1 | not-accessible | The table vdsl2PMLineCurrTable contains current Performance Monitoring results of VDSL2 line. The indexes of this table are an interface index where the interface has an ifType of vdsl2(251) and the termination unit. | |
| vdsl2PMLineCurrEntry | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1 | not-accessible | The table vdsl2PMLineCurrTable contains current Performance Monitoring results of VDSL2 line. The indexes of this entry are an interface index where the interface has an ifType of vdsl2(251) and the termination unit. | |
| VDS vdsl2PMLCurrUnit | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.1 | Vdsl2Unit | not-accessible | The termination unit XTUC{1} or XTUR{2}. |
| U32 vdsl2PMLCurrValidIntervals | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.2 | Unsigned32 | read-only | Valid intervals. |
| U32 vdsl2PMLCurrInvalidIntervals | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.3 | Unsigned32 | read-only | Invalid intervals. |
| HCP vdsl2PMLCurr15MTimeElapsed | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.4 | HCPerfTimeElapsed | read-only | Total elapsed seconds in this interval. Unit: seconds |
| C32 vdsl2PMLCurr15MFecsEx | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.5 | Counter32 | read-only | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Unit: seconds |
| C32 vdsl2PMLCurr15MEs | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.6 | Counter32 | read-only | Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >=1 OR LPR >= 1 xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >=1 OR RDI >=1 OR LPR-FE >=1 . This parameter is inhibited during UAS. Unit: seconds |
| C32 vdsl2PMLCurr15MSes | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.7 | Counter32 | read-only | Count of seconds during this interval that there was: xTU-C: If G.998.4 is supported and retransmission is enabled in the near-end received direction, a SES is declared if during a 1-second interval, there is one or more severe loss of error-free throughput (seftr) defect in the near-end received direction. Or else, an SES is declared if, during a 1 second interval, there are 18 or more CRC 8 anomalies in one or more of the received bearer channels, or one or more LOS defects, or one or more SEF defects, or one or more LPR defects. xTU-R: If G.998.4 is supported and retransmission is enabled in the far-end received direction, a SES-LFE is declared if during a 1-second interval, there is one or more severe loss of error-free throughput (seftr) defect in the far-end received direction. Or else, an SES is declared if, during a 1 second interval, there are 18 or more FEBE anomalies in one or more of the transmitted bearer channels, or one or more far end LOS defects, or one or more RDI defects, or one or more LPR FE defects. This parameter is inhibited during UAS. Unit: seconds |
| C32 vdsl2PMLCurr15MLoss | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.8 | Counter32 | read-only | Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R). Unit: seconds |
| C32 vdsl2PMLCurr15MUas | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.9 | Counter32 | read-only | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely-errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds. Unit: seconds |
| U32 vdsl2PMLCurr1DayValidIntervals | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.10 | Unsigned32 | read-only | Valid intervals. |
| U32 vdsl2PMLCurr1DayInvalidIntervals | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.11 | Unsigned32 | read-only | Invalid intervals. |
| HCP vdsl2PMLCurr1DayTimeElapsed | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.12 | HCPerfTimeElapsed | read-only | Total elapsed seconds in this interval. Unit: seconds |
| C32 vdsl2PMLCurr1DayFecs | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.13 | Counter32 | read-only | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Unit: seconds |
| C32 vdsl2PMLCurr1DayEs | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.14 | Counter32 | read-only | Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS. Unit: seconds |
| C32 vdsl2PMLCurr1DaySes | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.15 | Counter32 | read-only | Count of seconds during this interval that there was: xTU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 This parameter is inhibited during UAS. Unit: seconds |
| C32 vdsl2PMLCurr1DayLoss | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.16 | Counter32 | read-only | Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R). Unit: seconds |
| C32 vdsl2PMLCurr1DayUas | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.17 | Counter32 | read-only | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds. Unit: seconds |
| C32 vdsl2PMLEverBeforeFecs | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.18 | Counter32 | read-only | Count of seconds since agent reset that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Huawei defined. Unit: seconds |
| C32 vdsl2PMLEverBeforeEs | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.19 | Counter32 | read-only | Count of seconds since agent reset that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS. Huawei defined. Unit: seconds |
| C32 vdsl2PMLEverBeforeSes | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.20 | Counter32 | read-only | Count of seconds since agent reset that there was: xTU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 This parameter is inhibited during UAS. Huawei defined. Unit: seconds |
| C32 vdsl2PMLEverBeforeLoss | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.21 | Counter32 | read-only | Count of seconds since agent reset that there was LOS (or LOS-FE for xTU-R). Huawei defined. Unit: seconds |
| C32 vdsl2PMLEverBeforeUas | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.22 | Counter32 | read-only | Count of seconds in Unavailability State since agent reset. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds. Huawei defined. Unit: seconds |
| C32 vdsl2PMLCurr15MLofs | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.23 | Counter32 | read-only | Count of seconds in the current 15 minute interval when there was Loss of Framing. Unit: seconds |
| C32 vdsl2PMLCurr15MLols | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.24 | Counter32 | read-only | Count of seconds in the current 15 minute interval when there was Loss of Link. Unit: seconds |
| C32 vdsl2PMLCurr15MLops | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.25 | Counter32 | read-only | Count of seconds in the current 15 minute interval when there was Loss of Power. Unit: seconds |
| C32 vdsl2PMLCurr1DayLofs | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.26 | Counter32 | read-only | Count of the number of seconds when there was Loss of Framing during the current day. Unit: seconds |
| C32 vdsl2PMLCurr1DayLols | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.27 | Counter32 | read-only | Count of the number of seconds when there was Loss of Link during the current day. Unit: seconds |
| C32 vdsl2PMLCurr1DayLops | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.28 | Counter32 | read-only | Count of the number of seconds when there was Loss of Power during the current day. Unit: seconds |
| C32 vdsl2PMLEverBeforeLofs | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.29 | Counter32 | read-only | Count of the number of seconds when there was Loss of Framing since agent reset. Unit: seconds |
| C32 vdsl2PMLEverBeforeLols | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.30 | Counter32 | read-only | Count of the number of seconds when there was Loss of Link since agent reset. Unit: seconds |
| C32 vdsl2PMLEverBeforeLops | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.31 | Counter32 | read-only | Count of the number of seconds when there was Loss of Power since agent reset. Unit: seconds |
| C32 vdsl2PMLCurr15MSosSuccess | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.32 | Counter32 | read-only | Count of the total number of successful SOS procedures initiated in the current 15 minute. Unit: times |
| C32 vdsl2PMLCurr1DaySosSuccess | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.33 | Counter32 | read-only | Count of the total number of successful SOS procedures initiated during the current day. Unit: times |
| C32 vdsl2PMLEverBeforeSosSuccess | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.34 | Counter32 | read-only | Count of the total number of successful SOS procedures initiated since agent reset. Unit: times |
| OCT vdsl2PMLCurr15MInmainpeq | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.35 | OCTET STRING | read-only | This parameter is a count of the INMAINPEQi anomalies occurring on the line during current 15 minutes. |
| C32 vdsl2PMLCurr15MInmame | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.36 | Counter32 | read-only | This parameter is a count of the INMAME anomalies occurring on the line during current 15 minutes. |
| OCT vdsl2PMLCurr15MInmaiat | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.37 | OCTET STRING | read-only | This parameter is a count of the INMAIATi anomalies occurring on the line during current 15 minutes. |
| OCT vdsl2PMLCurr1DayInmainpeq | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.38 | OCTET STRING | read-only | This parameter is a count of the INMAINPEQi anomalies occurring on the line during current 1 day. |
| C32 vdsl2PMLCurr1DayInmame | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.39 | Counter32 | read-only | This parameter is a count of the INMAME anomalies occurring on the line during current 1 day. |
| OCT vdsl2PMLCurr1DayInmaiat | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.40 | OCTET STRING | read-only | This parameter is a count of the INMAIATi anomalies occurring on the line during current 1 day. |
| OCT vdsl2PMLEverBeforeInmainpeq | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.41 | OCTET STRING | read-only | This parameter is a count of the INMAINPEQi anomalies occurring on the line ever before. |
| C32 vdsl2PMLEverBeforeInmame | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.42 | Counter32 | read-only | This parameter is a count of the INMAME anomalies occurring on the line ever before. |
| OCT vdsl2PMLEverBeforeInmaiat | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.43 | OCTET STRING | read-only | This parameter is a count of the INMAIATi anomalies occurring on the line ever before. |
| DAT vdsl2PMLineCurr15MStartTime | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.44 | DateAndTime | read-only | Start time of the current 15-minute performance statistics. |
| DAT vdsl2PMLineCurr1DayStartTime | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.45 | DateAndTime | read-only | Start time of the current 1-day performance statistics. |
| C32 vdsl2PMLCurr15MLeftrs | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.46 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 15 minutes accumulation period. |
| C32 vdsl2PMLCurr15MEfb | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.47 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 15 minutes accumulation period. |
| C32 vdsl2PMLCurr15MMinEftr | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.48 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 15 minutes accumulation period. |
| C32 vdsl2PMLCurr1DayLeftrs | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.49 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 24 hours accumulation period. |
| C32 vdsl2PMLCurr1DayEfb | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.50 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 24 hours accumulation period. |
| C32 vdsl2PMLCurr1DayMinEftr | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.51 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 24 hours accumulation period. |
| C32 vdsl2PMLEverBeforeLeftrs | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.52 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed ever before. |
| C32 vdsl2PMLEverBeforeEfb | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.53 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed ever before. |
| C32 vdsl2PMLEverBeforeMinEftr | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.54 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed ever before. |
| C32 hwvdsl2PMLEverBeforeSraDownShiftEvent | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.55 | Counter32 | read-only | This parameter is a count of sra downshift event occurring on the line ever before. |
| C32 hwvdsl2PMLEverBeforeSraUpShiftEvent | 1.3.6.1.4.1.2011.6.115.1.4.1.1.1.56 | Counter32 | read-only | This parameter is a count of sra upshift event occurring on the line ever before. |
| vdsl2PMLineCurrInitTable | 1.3.6.1.4.1.2011.6.115.1.4.1.2 | not-accessible | The table vdsl2PMLineCurrInitTable contains current initialization counters of VDSL2 line. The indexes of this table are an interface index where the interface has an ifType of vdsl2(251) and the termination unit. | |
| vdsl2PMLineCurrInitEntry | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1 | not-accessible | The table vdsl2PMLineCurrInitTable contains current initialization counters of VDSL2 line. The indexes of this entry are an interface index where the interface has an ifType of vdsl2(251) and the termination unit. | |
| U32 vdsl2PMLCurrInit15MTimeElapsed | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.1 | Unsigned32 | read-only | Total elapsed seconds in this interval. Unit: seconds |
| U32 vdsl2PMLCurrInit15MFullInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.2 | Unsigned32 | read-only | Count of full initializations attempted on the line (successful and failed) during this interval. |
| U32 vdsl2PMLCurrInit15MFailedFullInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.3 | Unsigned32 | read-only | Count of failed full initializations on the line during this interval. |
| U32 vdsl2PMLCurrInit15MShortInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.4 | Unsigned32 | read-only | Count of short initializations attempted on the line (successful and failed) during this interval. |
| U32 vdsl2PMLCurrInit15MFailedShortInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.5 | Unsigned32 | read-only | Count of failed short initializations on the line during this interval. |
| U32 vdsl2PMLCurrInit1DayTimeElapsed | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.6 | Unsigned32 | read-only | Total elapsed seconds in this interval. Unit: seconds |
| U32 vdsl2PMLCurrInit1DayFullInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.7 | Unsigned32 | read-only | Count of full initializations attempted on the line (successful and failed) during this interval. |
| U32 vdsl2PMLCurrInit1DayFailedFullInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.8 | Unsigned32 | read-only | Count of failed full initializations on the line during this interval. |
| U32 vdsl2PMLCurrInit1DayShortInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.9 | Unsigned32 | read-only | Count of short initializations attempted on the line (successful and failed) during this interval. |
| U32 vdsl2PMLCurrInit1DayFailedShortInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.10 | Unsigned32 | read-only | Count of failed short initializations on the line during this interval. |
| U32 vdsl2PMLInitEverBeforeFullInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.11 | Unsigned32 | read-only | Count of full initializations attempted on the line (successful and failed) since agent reset. Huawei defined. |
| U32 vdsl2PMLInitEverBeforeFailedFullInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.12 | Unsigned32 | read-only | Count of failed full initializations on the line since agent reset. Huawei defined. |
| U32 vdsl2PMLInitEverBeforeShortInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.13 | Unsigned32 | read-only | Count of short initializations attempted on the line (successful and failed) since agent reset. Huawei defined. |
| U32 vdsl2PMLInitEverBeforeFailedShortInits | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.14 | Unsigned32 | read-only | Count of failed short initializations on the line since agent reset. Huawei defined. |
| DAT vdsl2PMLineCurrInit15MStartTime | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.15 | DateAndTime | read-only | Start time of the current initializations 15-minute performance statistics. |
| DAT vdsl2PMLineCurrInit1DayStartTime | 1.3.6.1.4.1.2011.6.115.1.4.1.2.1.16 | DateAndTime | read-only | Start time of the current initializations 1-day performance statistics. |
| vdsl2PMLineHist15MinTable | 1.3.6.1.4.1.2011.6.115.1.4.1.3 | not-accessible | The table vdsl2PMLineHist15MinTable contains PM line history for 15min intervals of VDSL2 line. The indexes of this table are an interface index where the interface has an ifType of vdsl2(251), the termination unit, and an interval number. | |
| vdsl2PMLineHist15MinEntry | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1 | not-accessible | The table vdsl2PMLineHist15MinTable contains PM line history for 15min intervals of VDSL2 line. The indexes of this entry are an interface index where the interface has an ifType of vdsl2(251), the termination unit, and an interval number. | |
| VDS vdsl2PMLHist15MUnit | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.1 | Vdsl2Unit | not-accessible | The termination unit XTUC{1} or XTUR{2}. |
| U32 vdsl2PMLHist15MInterval | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.2 | Unsigned32 | not-accessible | The interval number. |
| U32 vdsl2PMLHist15MMonitoredTime | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.3 | Unsigned32 | read-only | Total seconds monitored in this interval. Unit: seconds |
| C32 vdsl2PMLHist15MFecs | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.4 | Counter32 | read-only | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Unit: seconds |
| C32 vdsl2PMLHist15MEs | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.5 | Counter32 | read-only | Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS. Unit: seconds |
| C32 vdsl2PMLHist15MSes | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.6 | Counter32 | read-only | Count of seconds during this interval that there was: xTU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS. Unit: seconds |
| C32 vdsl2PMLHist15MLoss | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.7 | Counter32 | read-only | Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R). Unit: seconds |
| C32 vdsl2PMLHist15MUas | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.8 | Counter32 | read-only | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds. Unit: seconds |
| T/F vdsl2PMLHist15MValidInterval | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.9 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| C32 vdsl2PMLHist15MLofs | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.10 | Counter32 | read-only | Count of seconds in the interval when there was Loss of Framing. Unit: seconds |
| C32 vdsl2PMLHist15MLols | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.11 | Counter32 | read-only | Count of seconds in the interval when there was Loss of Link. Unit: seconds |
| C32 vdsl2PMLHist15MLops | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.12 | Counter32 | read-only | Count of seconds in the interval when there was Loss of Power. Unit: seconds |
| C32 vdsl2PMLHist15MSosSuccess | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.13 | Counter32 | read-only | Count of the total number of successful SOS procedures initiated in the interval. Unit: times |
| OCT vdsl2PMLHist15MInmainpeq | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.14 | OCTET STRING | read-only | This parameter is a count of the INMAINPEQi anomalies occurring on the line over the 15 minutes accumulation period. |
| C32 vdsl2PMLHist15MInmame | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.15 | Counter32 | read-only | This parameter is a count of the INMAME anomalies occurring on the line over the 15 minutes accumulation period. |
| OCT vdsl2PMLHist15MInmaiat | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.16 | OCTET STRING | read-only | This parameter is a count of the INMAIATi anomalies occurring on the line over the 15 minutes accumulation period. |
| DAT vdsl2PMLHist15MStartTime | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.17 | DateAndTime | read-only | Start time of the historical 15-minute performance statistics. |
| C32 vdsl2PMLHist15MLeftrs | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.18 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 15 minutes accumulation period. |
| C32 vdsl2PMLHist15MEfb | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.19 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 15 minutes accumulation period. |
| C32 vdsl2PMLHist15MMinEftr | 1.3.6.1.4.1.2011.6.115.1.4.1.3.1.20 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 15 minutes accumulation period. |
| vdsl2PMLineHist1DayTable | 1.3.6.1.4.1.2011.6.115.1.4.1.4 | not-accessible | The table vdsl2PMLineHist1DayTable contains PM line history for 24 hours intervals of VDSL2 line. The indexes of this table are an interface index where the interface has an ifType of vdsl2(251), the termination unit and an interval number. | |
| vdsl2PMLineHist1DayEntry | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1 | not-accessible | The table vdsl2PMLineHist1DayTable contains PM line history for 24 hours intervals of VDSL2 line. The indexes of this entry are an interface index where the interface has an ifType of vdsl2(251), the termination unit and an interval number. | |
| VDS vdsl2PMLHist1DUnit | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.1 | Vdsl2Unit | not-accessible | The termination unit. |
| U32 vdsl2PMLHist1DInterval | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.2 | Unsigned32 | not-accessible | The interval number. |
| U32 vdsl2PMLHist1DMonitoredTime | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.3 | Unsigned32 | read-only | Total seconds monitored in this interval. Unit: seconds |
| C32 vdsl2PMLHist1DFecs | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.4 | Counter32 | read-only | Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Unit: seconds |
| C32 vdsl2PMLHist1DEs | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.5 | Counter32 | read-only | Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS. Unit: seconds |
| C32 vdsl2PMLHist1DSes | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.6 | Counter32 | read-only | Count of seconds during this interval that there was: xTU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >> 1 OR LPR >= 1 xTU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS. Unit: seconds |
| C32 vdsl2PMLHist1DLoss | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.7 | Counter32 | read-only | Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R). Unit: seconds |
| C32 vdsl2PMLHist1DUas | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.8 | Counter32 | read-only | Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds. Unit: seconds |
| T/F vdsl2PMLHist1DValidInterval | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.9 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| C32 vdsl2PMLHist1DLofs | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.10 | Counter32 | read-only | Count of seconds during this interval that there was Loss of Framing. Unit: seconds |
| C32 vdsl2PMLHist1DLols | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.11 | Counter32 | read-only | Count of seconds during this interval that there was Loss of Link. Unit: seconds |
| C32 vdsl2PMLHist1DLops | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.12 | Counter32 | read-only | Count of seconds during this interval that there was Loss of Power. Unit: seconds |
| C32 vdsl2PMLHist1DSosSuccess | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.13 | Counter32 | read-only | Count of the total number of successful SOS procedures initiated during this interval. Unit: times |
| OCT vdsl2PMLHist1DInmainpeq | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.14 | OCTET STRING | read-only | This parameter is a count of the INMAINPEQi anomalies occurring on the line over the 24 hours accumulation period. |
| C32 vdsl2PMLHist1DInmame | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.15 | Counter32 | read-only | This parameter is a count of the INMAME anomalies occurring on the line over the 24 hours accumulation period. |
| OCT vdsl2PMLHist1DInmaiat | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.16 | OCTET STRING | read-only | This parameter is a count of the INMAIATi anomalies occurring on the line over the 24 hours accumulation period. |
| DAT vdsl2PMLHist1DStartTime | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.17 | DateAndTime | read-only | Start time of the historical 1-day performance statistics. |
| C32 vdsl2PMLHist1DLeftrs | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.18 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 24 hours accumulation period. |
| C32 vdsl2PMLHist1DEfb | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.19 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 24 hours accumulation period. |
| C32 vdsl2PMLHist1DMinEftr | 1.3.6.1.4.1.2011.6.115.1.4.1.4.1.20 | Counter32 | read-only | If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 24 hours accumulation period. |
| vdsl2PMLineInitHist15MinTable | 1.3.6.1.4.1.2011.6.115.1.4.1.5 | not-accessible | The table vdsl2PMLineInitHist15MinTable contains PM line initialization history for 15 minutes intervals of VDSL2 line. The indexes of this table are an interface index where the interface has an ifType of vdsl2(251) and an interval number. | |
| vdsl2PMLineInitHist15MinEntry | 1.3.6.1.4.1.2011.6.115.1.4.1.5.1 | not-accessible | The table vdsl2PMLineInitHist15MinTable contains PM line initialization history for 15 minutes intervals of VDSL2 line. The indexes of this entry are an interface index where the interface has an ifType of vdsl2(251) and an interval number. | |
| U32 vdsl2PMLHistInit15MInterval | 1.3.6.1.4.1.2011.6.115.1.4.1.5.1.1 | Unsigned32 | not-accessible | The interval number. |
| U32 vdsl2PMLHistInit15MMonitoredTime | 1.3.6.1.4.1.2011.6.115.1.4.1.5.1.2 | Unsigned32 | read-only | Total seconds monitored in this interval. Unit: seconds |
| U32 vdsl2PMLHistInit15MFullInits | 1.3.6.1.4.1.2011.6.115.1.4.1.5.1.3 | Unsigned32 | read-only | Count of full initializations attempted on the line (successful and failed) during this interval. |
| U32 vdsl2PMLHistInit15MFailedFullInits | 1.3.6.1.4.1.2011.6.115.1.4.1.5.1.4 | Unsigned32 | read-only | Count of failed full initializations on the line during this interval. |
| U32 vdsl2PMLHistInit15MShortInits | 1.3.6.1.4.1.2011.6.115.1.4.1.5.1.5 | Unsigned32 | read-only | Count of short initializations attempted on the line (successful and failed) during this interval. |
| U32 vdsl2PMLHistInit15MFailedShortInits | 1.3.6.1.4.1.2011.6.115.1.4.1.5.1.6 | Unsigned32 | read-only | Count of failed short initializations on the line during this interval. |
| T/F vdsl2PMLHistInit15MValidInterval | 1.3.6.1.4.1.2011.6.115.1.4.1.5.1.7 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| DAT vdsl2PMLHistInit15MStartTime | 1.3.6.1.4.1.2011.6.115.1.4.1.5.1.8 | DateAndTime | read-only | Start time of the historical initializations 15-minute performance statistics. |
| vdsl2PMLineInitHist1DayTable | 1.3.6.1.4.1.2011.6.115.1.4.1.6 | not-accessible | The table vdsl2PMLineInitHist1DayTable contains PM line initialization history for 24 hours intervals of VDSL2 line. The indexes of this table are an interface index where the interface has an ifType of vdsl2(251) and an interval number. | |
| vdsl2PMLineInitHist1DayEntry | 1.3.6.1.4.1.2011.6.115.1.4.1.6.1 | not-accessible | The table vdsl2PMLineInitHist1DayTable contains PM line initialization history for 24 hours intervals of VDSL2 line. The indexes of this entry are an interface index where the interface has an ifType of vdsl2(251) and an interval number. | |
| U32 vdsl2PMLHistinit1DInterval | 1.3.6.1.4.1.2011.6.115.1.4.1.6.1.1 | Unsigned32 | not-accessible | The interval number. |
| U32 vdsl2PMLHistinit1DMonitoredTime | 1.3.6.1.4.1.2011.6.115.1.4.1.6.1.2 | Unsigned32 | read-only | Total seconds monitored in this interval. |
| U32 vdsl2PMLHistinit1DFullInits | 1.3.6.1.4.1.2011.6.115.1.4.1.6.1.3 | Unsigned32 | read-only | Count of full initializations attempted on the line (successful and failed) during this interval. |
| U32 vdsl2PMLHistinit1DFailedFullInits | 1.3.6.1.4.1.2011.6.115.1.4.1.6.1.4 | Unsigned32 | read-only | Count of failed full initializations on the line during this interval. |
| U32 vdsl2PMLHistinit1DShortInits | 1.3.6.1.4.1.2011.6.115.1.4.1.6.1.5 | Unsigned32 | read-only | Count of short initializations attempted on the line (successful and failed) during this interval. |
| U32 vdsl2PMLHistinit1DFailedShortInits | 1.3.6.1.4.1.2011.6.115.1.4.1.6.1.6 | Unsigned32 | read-only | Count of failed short initializations on the line during this interval. |
| T/F vdsl2PMLHistinit1DValidInterval | 1.3.6.1.4.1.2011.6.115.1.4.1.6.1.7 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| DAT vdsl2PMLHistinit1DStartTime | 1.3.6.1.4.1.2011.6.115.1.4.1.6.1.8 | DateAndTime | read-only | Start time of the historical initializations 1-day performance statistics. |
| vdsl2PMChannel | 1.3.6.1.4.1.2011.6.115.1.4.2 | |||
| vdsl2PMChCurrTable | 1.3.6.1.4.1.2011.6.115.1.4.2.1 | not-accessible | The table vdsl2PMChCurrTable contains current Performance Monitoring results of VDSL2 channel. The indexes of this table are an interface index where the interface has an ifType value which is applicable for a DSL channel and the termination unit. | |
| vdsl2PMChCurrEntry | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1 | not-accessible | The table vdsl2PMChCurrTable contains current Performance Monitoring results of VDSL2 channel. The indexes of this entry are an interface index where the interface has an ifType value which is applicable for a DSL channel and the termination unit. | |
| VDS vdsl2PMChCurrUnit | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.1 | Vdsl2Unit | not-accessible | The termination unit. |
| U32 vdsl2PMChCurrValidIntervals | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.2 | Unsigned32 | read-only | Valid intervals. |
| U32 vdsl2PMChCurrInvalidIntervals | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.3 | Unsigned32 | read-only | Invalid intervals. |
| HCP vdsl2PMChCurr15MTimeElapsed | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.4 | HCPerfTimeElapsed | read-only | Total elapsed seconds in this interval. Unit: seconds |
| U32 vdsl2PMChCurr15MCodingViolations | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.5 | Unsigned32 | read-only | Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels. |
| U32 vdsl2PMChCurr15MCorrectedBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.6 | Unsigned32 | read-only | Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels. |
| U32 vdsl2PMChCurr1DayValidIntervals | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.7 | Unsigned32 | read-only | Valid intervals. |
| U32 vdsl2PMChCurr1DayInvalidIntervals | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.8 | Unsigned32 | read-only | Invalid intervals. |
| HCP vdsl2PMChCurr1DayTimeElapsed | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.9 | HCPerfTimeElapsed | read-only | Total elapsed seconds in this interval. Unit: seconds |
| U32 vdsl2PMChCurr1DayCodingViolations | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.10 | Unsigned32 | read-only | Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels. |
| U32 vdsl2PMChCurr1DayCorrectedBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.11 | Unsigned32 | read-only | Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels. |
| U32 vdsl2PMChEverBeforeCodingViolations | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.12 | Unsigned32 | read-only | Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels. Huawei defined. |
| U32 vdsl2PMChEverBeforeCorrectedBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.13 | Unsigned32 | read-only | Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel since agent reset. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels. Huawei defined. |
| U32 vdsl2PMChCurr15MEncodedBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.14 | Unsigned32 | read-only | Count of all encoded blocks received on this channel within the current 15 minute interval. |
| U32 vdsl2PMChCurr15MUncorrectableBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.15 | Unsigned32 | read-only | Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval. |
| U32 vdsl2PMChCurr1DayEncodedBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.16 | Unsigned32 | read-only | Count of all encoded blocks received on this channel during the current day. |
| U32 vdsl2PMChCurr1DayUncorrectableBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.17 | Unsigned32 | read-only | Count of all blocks received with uncorrectable errors on this channel during the current day. |
| U32 vdsl2PMChEverBeforeEncodedBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.18 | Unsigned32 | read-only | Count of all encoded blocks received on this channel since agent reset. |
| U32 vdsl2PMChEverBeforeUncorrectableBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.19 | Unsigned32 | read-only | Count of all blocks received with uncorrectable errors since agent reset. |
| C32 vdsl2PMChCurr15MAtmCells | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.20 | Counter32 | read-only | Count of Atm Cells received within the current 15 minute interval. |
| C32 vdsl2PMChCurr15MPtmPackets | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.21 | Counter32 | read-only | Count of Ptm Packet received within the current 15 minute interval. |
| C32 vdsl2PMChCurr1DayAtmCells | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.22 | Counter32 | read-only | Count of Atm Cells received during the current day. |
| C32 vdsl2PMChCurr1DayPtmPackets | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.23 | Counter32 | read-only | Count of Ptm Packets received during the current day. |
| C64 vdsl2PMChEverBeforeAtmCells | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.24 | Counter64 | read-only | Count of Atm Cells received since agent reset. |
| C64 vdsl2PMChEverBeforePtmPackets | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.25 | Counter64 | read-only | Count of Ptm Packets received since agent reset. |
| C32 vdsl2PMChCurr15MRtxCW | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.26 | Counter32 | read-only | Count of units request retransmission within the current 15 minute interval. |
| C32 vdsl2PMChCurr15MRtxCorrectedCW | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.27 | Counter32 | read-only | Count of units corrected by retransmission within the current 15 minute interval. |
| C32 vdsl2PMChCurr15MRtxUncorrectedCW | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.28 | Counter32 | read-only | Count of units uncorrected by retransmission within the current 15 minute interval. |
| C32 vdsl2PMChCurr1DayRtxCW | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.29 | Counter32 | read-only | Count of units request retransmission during the current day. |
| C32 vdsl2PMChCurr1DayRtxCorrectedCW | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.30 | Counter32 | read-only | Count of units corrected by retransmission during the current day. |
| C32 vdsl2PMChCurr1DayRtxUncorrectedCW | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.31 | Counter32 | read-only | Count of units uncorrected by retransmission during the current day. |
| C32 vdsl2PMChEverBeforeRtxCW | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.32 | Counter32 | read-only | Count of units request retransmission since agent reset. |
| C32 vdsl2PMChEverBeforeRtxCorrectedCW | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.33 | Counter32 | read-only | Count of units corrected by retransmission since agent reset. |
| C32 vdsl2PMChEverBeforeRtxUncorrectedCW | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.34 | Counter32 | read-only | Count of units uncorrected by retransmission since agent reset. |
| DAT vdsl2PMChCurr15MStartTime | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.35 | DateAndTime | read-only | Start time of the channel current 15-minute performance statistics. |
| DAT vdsl2PMChCurr1DayStartTime | 1.3.6.1.4.1.2011.6.115.1.4.2.1.1.36 | DateAndTime | read-only | Start time of the channel current 1-day performance statistics. |
| vdsl2PMChHist15MinTable | 1.3.6.1.4.1.2011.6.115.1.4.2.2 | not-accessible | The table vdsl2PMChHist15MinTable contains PM channel history for 15min intervals of VDSL2 channel. The indexes of this table are an interface index where the interface has an ifType value which is applicable for a DSL channel, the termination unit and the interval number. | |
| vdsl2PMChHist15MinEntry | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1 | not-accessible | The table vdsl2PMChHist15MinTable contains PM channel history for 15min intervals of VDSL2 channel. The indexes of this entry are an interface index where the interface has an ifType value which is applicable for a DSL channel, the termination unit and the interval number. | |
| VDS vdsl2PMChHist15MUnit | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.1 | Vdsl2Unit | not-accessible | The termination unit. |
| U32 vdsl2PMChHist15MInterval | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.2 | Unsigned32 | not-accessible | The interval number. |
| U32 vdsl2PMChHist15MMonitoredTime | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.3 | Unsigned32 | read-only | Total seconds monitored in this interval. Unit: seconds |
| U32 vdsl2PMChHist15MCodingViolations | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.4 | Unsigned32 | read-only | Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels. |
| U32 vdsl2PMChHist15MCorrectedBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.5 | Unsigned32 | read-only | Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels. |
| T/F vdsl2PMChHist15MValidInterval | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.6 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| U32 vdsl2PMChHist15MEncodedBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.7 | Unsigned32 | read-only | Count of all encoded blocks received on this channel during the interval. |
| U32 vdsl2PMChHist15MUncorrectableBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.8 | Unsigned32 | read-only | Count of all blocks received with uncorrectable errors on this channel during the interval. |
| C32 vdsl2PMChHist15MAtmCells | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.9 | Counter32 | read-only | Count of Atm Cells received on this channel during the interval. |
| C32 vdsl2PMChHist15MPtmPackets | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.10 | Counter32 | read-only | Count of Ptm Packets received on this channel during the interval. |
| C32 vdsl2PMChHist15MRtxCW | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.11 | Counter32 | read-only | Count of units request retransmission during the serval 15 minute interval of history. |
| C32 vdsl2PMChHist15MRtxCorrectedCW | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.12 | Counter32 | read-only | Count of units corrected by retransmission during the serval 15 minute interval of history. |
| C32 vdsl2PMChHist15MRtxUncorrectedCW | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.13 | Counter32 | read-only | Count of units uncorrected by retransmission during the serval 15 minute interval of history. |
| DAT vdsl2PMChHist15MStartTime | 1.3.6.1.4.1.2011.6.115.1.4.2.2.1.14 | DateAndTime | read-only | Start time of the channel historical 15-minute performance statistics. |
| vdsl2PMChHist1DTable | 1.3.6.1.4.1.2011.6.115.1.4.2.3 | not-accessible | The table vdsl2PMChHist1DTable contains PM channel history for 1 day intervals of VDSL2. The indexes of this table are an interface index where the interface has an ifType value which is applicable for a DSL channel, the termination unit and the interval number. | |
| vdsl2PMChHist1DEntry | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1 | not-accessible | The table vdsl2PMChHist1DTable contains PM channel history for 1 day intervals of VDSL2. The indexes of this entry are an interface index where the interface has an ifType value which is applicable for a DSL channel, the termination unit and the interval number. | |
| VDS vdsl2PMChHist1DUnit | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.1 | Vdsl2Unit | not-accessible | The termination unit. |
| U32 vdsl2PMChHist1DInterval | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.2 | Unsigned32 | not-accessible | The interval number. |
| U32 vdsl2PMChHist1DMonitoredTime | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.3 | Unsigned32 | read-only | Total seconds monitored in this interval. Unit: seconds |
| U32 vdsl2PMChHist1DCodingViolations | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.4 | Unsigned32 | read-only | Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels. |
| U32 vdsl2PMChHist1DCorrectedBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.5 | Unsigned32 | read-only | Count of FEC (FFEC for xTU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels. |
| T/F vdsl2PMChHist1DValidInterval | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.6 | TruthValue | read-only | This variable indicates if the data for this interval is valid. |
| U32 vdsl2PMChHist1DEncodedBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.7 | Unsigned32 | read-only | Count of all encoded blocks received on this channel during the interval. |
| U32 vdsl2PMChHist1DUncorrectableBlocks | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.8 | Unsigned32 | read-only | Count of all blocks received with uncorrectable errors on this channel during the interval. |
| C32 vdsl2PMChHist1DAtmCells | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.9 | Counter32 | read-only | Count of Atm Cells received on this channel during the interval. |
| C32 vdsl2PMChHist1DPtmPackets | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.10 | Counter32 | read-only | Count of Ptm Packets received on this channel during the interval. |
| C32 vdsl2PMChHist1DRtxCW | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.11 | Counter32 | read-only | Count of units request retransmission within the serval one day interval of history. |
| C32 vdsl2PMChHist1DRtxCorrectedCW | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.12 | Counter32 | read-only | Count of units corrected by retransmission during the serval one day interval of history. |
| C32 vdsl2PMChHist1DRtxUncorrectedCW | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.13 | Counter32 | read-only | Count of units uncorrected by retransmission during the serval one day interval of history. |
| DAT vdsl2PMChHist1DStartTime | 1.3.6.1.4.1.2011.6.115.1.4.2.3.1.14 | DateAndTime | read-only | Start time of the channel historical 1-day performance statistics. |
| vdsl2PMChChipStatTable | 1.3.6.1.4.1.2011.6.115.1.4.2.4 | not-accessible | The table vdsl2PMChChipStatTable contains packets and CRC errors on chipset of upstream and downstream of VDSL2 channel. The indexes of this table are an interface index where the interface has an ifType value which is applicable for a DSL channel and the termination unit. | |
| vdsl2PMChChipStatEntry | 1.3.6.1.4.1.2011.6.115.1.4.2.4.1 | not-accessible | The table vdsl2PMChChipStatTable contains packets and CRC errors on chipset of upstream and downstream of VDSL2 channel. The indexes of this entry are an interface index where the interface has an ifType value which is applicable for a DSL channel and the termination unit. | |
| VDS vdsl2PMChChipstatUnit | 1.3.6.1.4.1.2011.6.115.1.4.2.4.1.1 | Vdsl2Unit | not-accessible | The termination unit. |
| U32 vdsl2PMChPktsDs | 1.3.6.1.4.1.2011.6.115.1.4.2.4.1.2 | Unsigned32 | read-only | The number of downstream packets. |
| U32 vdsl2PMChPktsUs | 1.3.6.1.4.1.2011.6.115.1.4.2.4.1.3 | Unsigned32 | read-only | The number of upstream packets. |
| U32 vdsl2PMChCrcErrsDs | 1.3.6.1.4.1.2011.6.115.1.4.2.4.1.4 | Unsigned32 | read-only | The number of downstream CRC errors. |
| U32 vdsl2PMChCrcErrsUs | 1.3.6.1.4.1.2011.6.115.1.4.2.4.1.5 | Unsigned32 | read-only | The number of upstream CRC errors. |
| INT vdsl2PMChStatAdminStatus | 1.3.6.1.4.1.2011.6.115.1.4.2.4.1.6 | INTEGER | read-write | Clear the number of packets transmitted and received, CRC errors upstream and downstream. Options: 1. reset(1) - reset statistic data |
| vdsl2Profile | 1.3.6.1.4.1.2011.6.115.1.5 | |||
| vdsl2ProfileLine | 1.3.6.1.4.1.2011.6.115.1.5.1 | |||
| vdsl2LineConfTemplateTable | 1.3.6.1.4.1.2011.6.115.1.5.1.1 | not-accessible | The table vdsl2LineConfTemplateTable contains VDSL2 line configuration template. The index of this table is vdsl2LConfTempTemplateName. A default template with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| vdsl2LineConfTemplateEntry | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1 | not-accessible | The table vdsl2LineConfTemplateTable contains VDSL2 line configuration template. The index of this entry is vdsl2LConfTempTemplateName. A default template with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| OCT vdsl2LConfTempTemplateName | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| OCT vdsl2LConfTempLineProfile | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.2 | OCTET STRING | read-create | The value of this object identifies the row in the VDSL2 Line Configuration Profile Table, (Vdsl2LineConfProfileTable), which applies for this VDSL2 line. |
| OCT vdsl2LConfTempChan1ConfProfile | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.3 | OCTET STRING | read-create | The value of this object identifies the row in the VDSL2 Channel Configuration Profile Table, (Vdsl2ChanConfProfileTable) that applies to VDSL2 bearer channel #1. The channel profile name specified here must match the name of an existing row in the vdsl2ChConfProfileTable table. |
| U32 vdsl2LConfTempChan1RaRatioDs | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.4 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Vdsl2ConfTemplateChan1RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. Unit: percents |
| U32 vdsl2LConfTempChan1RaRatioUs | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.5 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Vdsl2ConfTemplateChan1RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100 %. Unit: percents |
| OCT vdsl2LConfTempChan2ConfProfile | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.6 | OCTET STRING | read-create | The value of this object identifies the row in the VDSL2 Channel Configuration Profile Table, (Vdsl2ChanConfProfileTable) that applies to VDSL2 bearer channel #2. If the channel is unused, then the object is set to a zero length string. This object may be set to a zero length string only if vdsl2LConfTempChan3ConfProfile contains a zero length string. |
| U32 vdsl2LConfTempChan2RaRatioDs | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.7 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Vdsl2ConfTemplateChan2RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. Unit: percents |
| U32 vdsl2LConfTempChan2RaRatioUs | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.8 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Vdsl2ConfTemplateChan2RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100 %. Unit: percents |
| OCT vdsl2LConfTempChan3ConfProfile | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.9 | OCTET STRING | read-create | The value of this object identifies the row in the VDSL2 Channel Configuration Profile Table, (Vdsl2ChanConfProfileTable) that applies to VDSL2 bearer channel #3. If the channel is unused, then the object is set to a zero length string. This object may be set to a zero length string only if vdsl2LConfTempChan4ConfProfile contains a zero length string. This object may be set to a non-zero length string only if vdsl2LConfTempChan2ConfProfile contains a non-zero length string. |
| U32 vdsl2LConfTempChan3RaRatioDs | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.10 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Vdsl2ConfTemplateChan3RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. Unit: percents |
| U32 vdsl2LConfTempChan3RaRatioUs | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.11 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - Vdsl2ConfTemplateChan3RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. Unit: percents |
| OCT vdsl2LConfTempChan4ConfProfile | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.12 | OCTET STRING | read-create | The value of this object identifies the row in the VDSL2 Channel Configuration Profile Table (Vdsl2ChanConfProfileTableDs) that applies to VDSL2 bearer channel #4. If the channel is unused, then the object is set to a zero length string. This object may be set to a non-zero length string only if vdsl2LConfTempChan3ConfProfile contains a non-zero length string. |
| U32 vdsl2LConfTempChan4RaRatioDs | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.13 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - vdsl2LConfTempChan4RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%. Unit: percents |
| U32 vdsl2LConfTempChan4RaRatioUs | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.14 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - vdsl2LConfTempChan4RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%. Unit: percents |
| ROW vdsl2LConfTempRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.1.1.1.15 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated lines. |
| vdsl2LineConfProfTable | 1.3.6.1.4.1.2011.6.115.1.5.1.2 | not-accessible | The table vdsl2LineConfProfTable contains VDSL2 line profile configuration. The index of this table is vdsl2LConfProfProfileName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| vdsl2LineConfProfEntry | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1 | not-accessible | The table vdsl2LineConfProfTable contains VDSL2 line profile configuration. The index of this entry is vdsl2LConfProfProfileName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| OCT vdsl2LConfProfProfileName | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| VDS vdsl2LConfProfScMaskDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.2 | Vdsl2ScMaskDs | read-create | Sub-carriers mask. A bitmap of 512 bits that allows masking up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCds < 512, all bits i (NSCds i <= 512) should be set to '1'. |
| VDS vdsl2LConfProfScMaskUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.3 | Vdsl2ScMaskUs | read-create | Sub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the respective upstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCus < 64, all bits i (NSCus < i <= 64) should be set to '1'. |
| OCT vdsl2LConfProfRfiBands | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.4 | OCTET STRING | read-create | The subset of PSD mask breakpoints that shall be used to notch an RFI band. It is a string of bands consist of begin tone index and end tone index. for example :0-10,20-50,100-4095 It can contain as most as 16 bands. |
| OCT vdsl2LConfProfVDSLtoneblackout | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.5 | OCTET STRING | read-create | The subset of subcarriermask that shall be used to mask the subcarriers. It is a string of bands consist of begin tone index and end tone index. for example :0-10,20-50,100-4095 It can contain as most as 8 bands. |
| INT vdsl2LConfProfRaModeDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.6 | INTEGER | read-create | The mode of operation of a rate-adaptive xTU-C in the transmit direction. Options: 1. manual(1) - No Rate-Adaptation. The initialization process attempts to synchronize to a specified rate 2. rainit(2) - Rate-Adaptation during initialization process only, which attempts to synchronize to a rate between minimum and maximum specified values 3. dynamic(3) - Rate-Adaptation during show time 4. dynamicwithsos(4) - Rate-Adaptation during show time by SOS and SRA. In this mode, enabling of SOS and SRA is mandatory. |
| INT vdsl2LConfProfRaModeUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.7 | INTEGER | read-create | The mode of operation of a rate-adaptive xTU-R in the transmit direction. Options: 1. manual(1) - No Rate-Adaptation. The initialization process attempts to synchronize to a specified rate 2. rainit(2) - Rate-Adaptation during initialization process only, which attempts to synchronize to a rate between minimum and maximum specified values 3. dynamic(3) - Rate-Adaptation during show time 4. dynamicwithsos(4) - Rate-Adaptation during show time by SOS and SRA. In this mode, enabling of SOS and SRA is mandatory. |
| U32 vdsl2LConfProfRaUsNrmDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.8 | Unsigned32 | read-create | The Downstream Up-Shift Noise Margin value, to be used when Vdsl2LineConfRaModeDs is set to DynamicRa. If the downstream noise margin is above this value and stays above it for more than the time specified by the Vdsl2LineConfRaUsTimeDs, the xTU-R shall attempt to increase the downstream net data rate. The Downstream Up-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2LConfProfRaUsNrmUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.9 | Unsigned32 | read-create | The Upstream Up-Shift Noise Margin value, to be used when Vdsl2LineConfRaModeUs is set to DynamicRa. If the upstream noise margin is above this value and stays above it for more than the time specified by the Vdsl2LineConfRaUsTimeUs, the xTU-C shall attempt to increase the upstream net data rate. The Upstream Up-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2LConfProfRaUsTimeDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.10 | Unsigned32 | read-create | The Downstream Up-Shift Time Interval, to be used when Vdsl2LineConfRaModeDs is set to DynamicRa. The interval of time that the downstream noise margin should stay above the Downstream Up-shift Noise Margin before the xTU-R shall attempt to increase the downstream net data rate. The time interval ranges from 0 to 16383 seconds. Unit: seconds |
| U32 vdsl2LConfProfRaUsTimeUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.11 | Unsigned32 | read-create | The Upstream Up-Shift Time Interval, to be used when Vdsl2LineConfRaModeUs is set to DynamicRa. The interval of time the upstream noise margin should stay above the Upstream Up-shift Noise Margin before the xTU-C shall attempt to increase the upstream net data rate. Unit: seconds |
| U32 vdsl2LConfProfRaDsNrmsDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.12 | Unsigned32 | read-create | The Downstream Down-Shift Noise Margin value, to be used when Vdsl2LineConfRaModeDs is set to DynamicRa. If the downstream noise margin is below this value and stays below that for more than the time specified by the Vdsl2LineConfRaDsTimeDs, the xTU-R shall attempt to decrease the downstream net data rate. The Downstream Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2LConfProfRaDsNrmsUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.13 | Unsigned32 | read-create | The Upstream Downshift Noise Margin value, to be used when Vdsl2LineConfRaModeUs is set to DynamicRa. If the upstream noise margin is below this value and stays below that for more than the time specified by the Vdsl2LineConfRaDsTimeUs, the xTU-C shall attempt to decrease the upstream net data rate. The Upstream Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2LConfProfRaDsTimeDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.14 | Unsigned32 | read-create | The Downstream Downshift Time Interval, to be used when Vdsl2LineConfRaModeDs is set to DynamicRa. The interval of time the downstream noise margin should stay below the Downstream Down-shift Noise Margin before the xTU-R shall attempt to decrease the downstream net data rate. Unit: seconds |
| U32 vdsl2LConfProfRaDsTimeUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.15 | Unsigned32 | read-create | The Upstream Down-Shift Time Interval, to be used when Vdsl2LineConfRaModeUs is set to DynamicRa. The interval of time the upstream noise margin should stay below the Upstream Down-shift Noise Margin before the xTU-C shall attempt to decrease the upstream net data rate. Unit: seconds |
| U32 vdsl2LConfProfTargetSnrmDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.16 | Unsigned32 | read-create | The minimum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2LConfProfTargetSnrmUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.17 | Unsigned32 | read-create | The minimum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the upstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2LConfProfMaxSnrmDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.18 | Unsigned32 | read-create | The maximum Noise Margin the xTU-R receiver shall try to sustain. If the Noise Margin is above this level, the xTU-R shall request that the xTU-C reduce the xTU-C transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of all 1's means that there is no maximum. Unit: 0.1 dB |
| U32 vdsl2LConfProfMaxSnrmUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.19 | Unsigned32 | read-create | The maximum Noise Margin the xTU-C receiver shall try to sustain. If the Noise Margin is above this level, the xTU-C shall request that the xTU-R reduce the xTU-R transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of all 1's means that there is no maximum. Unit: 0.1 dB |
| U32 vdsl2LConfProfMinSnrmDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.20 | Unsigned32 | read-create | The minimum Noise Margin the xTU-R receiver shall tolerate. If the noise margin falls below this level, the xTU-R shall request that the xTU-C increase the xTU-C transmit power. If an increase to xTU-C transmit power is not possible, a loss-of-margin (LOM) defect occurs, the xTU-R shall fail and attempt to reinitialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0 means that there is no minimum. Unit: 0.1 dB |
| U32 vdsl2LConfProfMinSnrmUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.21 | Unsigned32 | read-create | The minimum Noise Margin the xTU-C receiver shall tolerate. If the noise margin falls below this level, the xTU-C shall request that the xTU-R increase the xTU-R transmit power. If an increase of xTU-R transmit power is not possible, a loss-of-margin (LOM) defect occurs, the xTU-C shall fail and attempt to re-initialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0 means that there is no minimum. Unit: 0.1 dB |
| U32 vdsl2LConfProfMsgMinUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.22 | Unsigned32 | read-create | Minimum Overhead Rate Upstream. Defines the minimum rate of the message-based overhead that shall be maintained by the xTU in upstream direction. Expressed in bits per second and ranges from 4000 to 63000 bps. Unit: bits/second |
| U32 vdsl2LConfProfMsgMinDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.23 | Unsigned32 | read-create | Minimum Overhead Rate Downstream. Defines the minimum rate of the message-based overhead that shall be maintained by the xTU in downstream direction. Expressed in bits per second and ranges from 4000 to 63000 bps. Unit: bits/second |
| VDS vdsl2LConfProfXtuTransSysEna | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.24 | Vdsl2TransmissionModeType | read-create | xTU Transmission System Enabling (XTSE). A list of the different coding types enabled in this profile. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the XTUs may apply the respective coding for the VDSL line. A bit set to '0' means that the XTUs cannot apply the respective coding for the VDSL line. All 'reserved' bits should be set to '0'. |
| VDS vdsl2LConfProfPmMode | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.25 | Vdsl2LConfProfPmMode | read-create | Power management state Enabling. Defines the power states the xTU-C or xTU-R may autonomously transition to on this line. Options: 1. allowTransitionsToIdle (0) 2. allowTransitionsToLowPower (1) A bit with a '1' value means that the xTU is allowed to transit into the respective state and a '0' value means that the xTU is not allowed to transit into the respective state. |
| U32 vdsl2LConfProfL0Time | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.26 | Unsigned32 | read-create | This minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. Unit: seconds |
| U32 vdsl2LConfProfL2Time | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.27 | Unsigned32 | read-create | This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. Unit: seconds |
| U32 vdsl2LConfProfL2Atpr | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.28 | Unsigned32 | read-create | The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It ranges from 0 dB to 31 dB. Unit: dB |
| U32 vdsl2LConfProfL2Atprt | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.29 | Unsigned32 | read-create | The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and Power Trims. Unit: dB |
| VDS vdsl2LConfProfDpboEpsd | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.30 | Vdsl2DpboEpsd | read-create | This parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as PSDMASKds.The maximum number of breakpoints for DPBOEPSD is 16. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff. |
| U32 vdsl2LConfProfDpboEsel | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.31 | Unsigned32 | read-create | This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid.If DPBOESEL is set to zero, the DPBO in this section shall be disabled. Unit: 0.5dB |
| VDS vdsl2LConfProfDpboEscm | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.32 | Vdsl2DpboEscm | read-create | This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid. Octets 0+1 DPBOESCMA Octets 2+3 DPBOESCMB Octets 4+5 DPBOESCMC |
| U32 vdsl2LConfProfDpboMus | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.33 | Unsigned32 | read-create | DPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX defined below. It shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid. Unit: -0.5dBm/Hz |
| U32 vdsl2LConfProfDpboFmin | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.34 | Unsigned32 | read-create | DPBOFMIN defines the minimum frequency from which the DPBO shall be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0) to 8832 kHz (coded as 2048). Unit: 4.3125 KHz |
| U32 vdsl2LConfProfDpboFmax | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.35 | Unsigned32 | read-create | DPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956). Unit: 4.3125 KHz |
| VDS vdsl2LConfProfUpboPsdBand | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.36 | Vdsl2UpboPsdBand | read-create | This parameter defines the UPBO reference PSD used to compute the upstream power back-off for each upstream band except US0. A UPBOPSD defined for each band shall consist of two parameters [a, b]. Parameter a shall be coded as an unsigned 12-bit number from 40 dBm/Hz (coded as 0) to 80.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz; and b shall be coded as an unsigned 12 bit number from 0 (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency f expressed in MHz shall be equal to '-a-b(SQRT(f))'. The set of parameter values a = 40 dBm/Hz, b = 0 dBm/Hz is a special configuration to disable UPBO in the respective upstream band. Octets 0+1 - a[0] Octets 2+3 - b[0] Octets 4+5 - a[1] Octets 6+7 - b[1] Octets 8+9 - a[2] Octets 10+11 - b[2] Octets 12+13 - a[3] Octets 14+15 - b[3] |
| U32 vdsl2LConfProfUpboKl | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.37 | Unsigned32 | read-create | This parameter defines the electrical loop length expressed in dB at 1MHz, kl0, configured by the CO-MIB. The value shall be coded as an unsigned 16 bit number in the range 0 (coded as 0) to 128 dB (coded as 1280) in steps of 0.1 dB. Unit: 0.1 dB |
| VDS vdsl2LConfProfUpboKlf | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.38 | Vdsl2UpboKlf | read-create | This parameter is a flag that forces the VTU-R to use the electrical loop length of the CO-MIB (UPBOKL) to compute the UPBO. The value shall be forced if the flag is set to 1. Otherwise, the electrical loop length shall be autonomously selected by the VTU-O. |
| ROW vdsl2LConfProfRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.39 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated templates. |
| VDS vdsl2LConfProfReferenceClock | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65534 | Vdsl2LineClockReferenceType | read-create | This object configures the clock reference for the ATU-C in a VDSL Line. |
| VDS vdsl2LConfProfBitSwapDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65535 | Vdsl2BitSwap | read-create | Enables or disables the bit swap downstream of a line. |
| VDS vdsl2LConfProfBitSwapUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65536 | Vdsl2BitSwap | read-create | Enables or disables the bit swap upstream of a line. |
| VDS vdsl2LConfProfUpboBoostMode | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65537 | Vdsl2UpboBoostMode | read-create | Options: 1. disable(1) - The Equalized FEXT UPBO method is not supported 2. enable(2) - The Equalized FEXT UPBO method is supported |
| U32 vdsl2LConfProfDpboEselMin | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65538 | Unsigned32 | read-create | DPBOESELMIN in dB is the minimum of all main cable losses for the KVz supplied when using the SOL model (expansion of a KVz and VDSL2 provision of additional KVz areas from this KVz using cross-cables to additional KVz), including the KVz at the MSAN site. This value must be adjustable as the minimum requirement via the SNMP interface in the configuration profile for each VDSL2 port, and is set individually for each MSAN site and usage. As an option, As an option, adjustment can be done for each MSAN or line card, thus taking effect for entire port groups. It is used only for determining the MUF. Unit: 0.5 dB |
| VDS vdsl2LConfProfUpboKl0RefBand | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65539 | Vdsl2UpboKl0RefBand | read-create | Octets 0+1 - length[1] Octets 2+3 - length[2] Octets 4+5 - length[3] Octets 6+7 - length[4] |
| U32 vdsl2LConfProfSosTimeDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65540 | Unsigned32 | read-create | The parameter is used in the specification of the receiver initiated SOS. If the value of this parameter is not zero, the standard SOS triggering criteria are enabled, and the value corresponds with duration of the time window used in the standard SOS triggering criteria in the downstream direction.The special value zero, indicates that the standard SOS triggering criteria are disabled. The valid range of non-zero values is from 64 ms to (255*64) ms in steps of 64ms. Unit: 64ms |
| U32 vdsl2LConfProfSosTimeUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65541 | Unsigned32 | read-create | The parameter is used in the specification of the receiver initiated SOS. If the value of this parameter is not zero, the standard SOS triggering criteria are enabled, and the value corresponds with duration of the time window used in the standard SOS triggering criteria in the upstream direction.The special value zero, indicates that the standard SOS triggering criteria are disabled. The valid range of non-zero values is from 64 ms to (255*64) ms in steps of 64ms. Unit: 64ms |
| U32 vdsl2LConfProfSosNtonesDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65542 | Unsigned32 | read-create | This parameter is defined as the minimum percentage of tones in the downstream MEDLEY SET that must be degraded in order to arm the first sub-condition of the standard SOS triggering criteria in the downstream direction. The parameter SOS-NTONES-ds is defined as a percentage of tones. The valid range of values is from 1 to 100 in steps of 1. A special value of 0 indicates that this parameter is not used in the decision criteria. |
| U32 vdsl2LConfProfSosNtonesUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65543 | Unsigned32 | read-create | This parameter is defined as the minimum percentage of tones in the upstream MEDLEY SET that must be degraded in order to arm the first sub-condition of the standard SOS triggering criteria in the downstream direction. The parameter SOS-NTONES-ds is defined as a percentage of tones. The valid range of values is from 1 to 100 in steps of 1. A special value of 0 indicates that this parameter is not used in the decision criteria. |
| U32 vdsl2LConfProfSosCrcDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65544 | Unsigned32 | read-create | This parameter is defined as the minimum number of normalized CRC anomalies received in SOS-TIME-ds seconds in order to arm the second sub-condition of the standard SOS triggering criteria in the downstream direction. The valid range of SOS-CRC values is 0.02 to 65535*0.02, in steps of 0.02. Unit: 0.02 |
| U32 vdsl2LConfProfSosCrcUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65545 | Unsigned32 | read-create | This parameter is defined as the minimum number of normalized CRC anomalies received in SOS-TIME-ds seconds in order to arm the second sub-condition of the standard SOS triggering criteria in the upstream direction. The valid range of SOS-CRC values is 0.02 to 65535*0.02, in steps of 0.02. Unit: 0.02 |
| U32 vdsl2LConfProfMaxSosDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65546 | Unsigned32 | read-create | This parameter is used in G.993.2 de-activation. If the number of successful SOS procedures in the downstream direction performed within a 120-second interval exceeds MAX-SOS-ds, the modem shall transition to the L3 state. The valid range of values is 1 to 15. A special value of 0 indicates that there is no limit on the maximum allowed number of SOS recoveries within this time interval. |
| U32 vdsl2LConfProfMaxSosUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65547 | Unsigned32 | read-create | This parameter is used in G.993.2 de-activation. If the number of successful SOS procedures in the upstream direction performed within a 120-second interval exceeds MAX-SOS-ds, the modem shall transition to the L3 state. The valid range of values is 1 to 15. A special value of 0 indicates that there is no limit on the maximum allowed number of SOS recoveries within this time interval. |
| U32 vdsl2LConfProfSnrmoffsetRocDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65548 | Unsigned32 | read-create | The parameter is defined as the SNR Margin offset for the ROC channel in the downstream direction. The parameter is used in the specification of the Channel Initialization Policy (see 12.3.7.1/G.993.2). The valid range of SNR margin offset values is from 0 to (310*0.1) dB with 0.1 dB steps. Unit: 0.1dB |
| U32 vdsl2LConfProfSnrmoffsetRocUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65549 | Unsigned32 | read-create | The parameter is defined as the SNR Margin offset for the ROC channel in the upstream direction. The parameter is used in the specification of the Channel Initialization Policy (see 12.3.7.1/G.993.2). The valid range of SNR margin offset values is from 0 to (310*0.1) dB with 0.1 dB steps. Unit: 0.1dB |
| U32 vdsl2LConfProfInpminRocDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65550 | Unsigned32 | read-create | This parameter contains the minimum impulse noise protection to apply on the ROC in the downstream direction. The minimum impulse noise protection is an integer ranging from 0 to 16. |
| U32 vdsl2LConfProfInpminRocUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65551 | Unsigned32 | read-create | This parameter contains the minimum impulse noise protection to apply on the robust ROC in the upstream direction. The minimum impulse noise protection is an integer ranging from 0 to 16. |
| U32 vdsl2LConfProfInmIatoDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65552 | Unsigned32 | read-create | The parameter of downstream impulse noise monitoring inter arrival time offset. This is the Inter Arrival Time Offset that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATO ranges from 3 to 511 DMT symbols in steps of 1 DMT symbol. |
| U32 vdsl2LConfProfInmIatsDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65553 | Unsigned32 | read-create | The parameter of downstream impulse noise monitoring inter arrival time step. This is the Inter Arrival Time Step that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATS ranges from 0 to 7 in steps of 1. |
| U32 vdsl2LConfProfInmCcDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65554 | Unsigned32 | read-create | The parameter of Downstream impulse noise monitoring cluster continuation value. This is the Cluster Continuation value that the xTU receiver shall use in the cluster indication process described in the relevant ITU-T Recommendation. The valid values for INMCC range from 0 to 64 DMT symbols in steps of 1 DMT symbol. |
| U32 vdsl2LConfProfInmInpeqModeDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65555 | Unsigned32 | read-create | The parameter of Downstream impulse noise monitoring equivalent impulse noise protect mode. This is the INM Equivalent INP Mode that the xTU receiver shall use in the computation of the Equivalent INP, as defined in the relevant ITU-T Recommendation. The valid values for INM-INPEQ-MODE are 0, 1, 2, 3, and 4. |
| U32 vdsl2LConfProfInmIatoUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65556 | Unsigned32 | read-create | The parameter of upstream impulse noise monitoring inter arrival time offset. This is the Inter Arrival Time Offset that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATO ranges from 3 to 511 DMT symbols in steps of 1 DMT symbol. |
| U32 vdsl2LConfProfInmIatsUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65557 | Unsigned32 | read-create | The parameter of upstream impulse noise monitoring inter arrival time step. This is the Inter Arrival Time Step that the xTU receiver shall use to determine in which bin of the Inter Arrival Time histogram the IAT is reported. The valid values for INMIATS ranges from 0 to 7 in steps of 1. |
| U32 vdsl2LConfProfInmCcUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65558 | Unsigned32 | read-create | The parameter of upstream impulse noise monitoring cluster continuation value. This is the Cluster Continuation value that the xTU receiver shall use in the cluster indication process described in the relevant ITU-T Recommendation. The valid values for INMCC range from 0 to 64 DMT symbols in steps of 1 DMT symbol. |
| U32 vdsl2LConfProfInmInpeqModeUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65559 | Unsigned32 | read-create | The parameter of upstream impulse noise monitoring equivalent impulse noise protect mode. This is the INM Equivalent INP Mode that the xTU receiver shall use in the computation of the Equivalent INP, as defined in the relevant ITU-T Recommendation. The valid values for INM-INPEQ-MODE are 0, 1, 2, 3, and 4. |
| U32 vdsl2LConfProfL3Time | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65560 | Unsigned32 | read-create | This minimum time (in seconds) between an Entry into the L3 state and the L0 or L2 state. Unit: seconds |
| INT vdsl2LConfProfRtxModeDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65561 | INTEGER | read-create | The mode of operation of G.998.4 retransmission in downstream direction. Options: 1. forbidden(0) - G.998.4 retransmission not allowed. 2. preferred(1) - G.998.4 retransmission is preferred. 3. forced(2) - Force the use of the G.998.4 retransmission. 4. testmode(3) - Force the use of the G.998.4 retransmission in test mode. |
| INT vdsl2LConfProfRtxModeUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65562 | INTEGER | read-create | The mode of operation of G.998.4 retransmission in upstream direction. Options: 1. forbidden(0) - G.998.4 retransmission not allowed. 2. preferred(1) - G.998.4 retransmission is preferred. 3. forced(2) - Force the use of the G.998.4 retransmission. 4. testmode(3) - Force the use of the G.998.4 retransmission in test mode. |
| U32 vdsl2LConfProfLeftrThreshDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65563 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the threshold for declaring a near-end leftr defect. The value is coded as a fraction of the NDR with valid range from 0.01 to 0.99 with increments of 0.01. A special value means the ETR shall be used as the default threshold for declaring a leftr defect. |
| U32 vdsl2LConfProfLeftrThreshUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65564 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the threshold for declaring a near-end leftr defect. The value is coded as a fraction of the NDR with valid range from 0.01 to 0.99 with increments of 0.01. A special value means the ETR shall be used as the default threshold for declaring a leftr defect. |
| T/F vdsl2LConfProfForceInpDs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65565 | TruthValue | read-create | This parameter indicates that the framer settings of the bearer shall be selected such that the impulse noise protection computed according to the formula specified in the relevant Recommendation is greater or equal to the minimal impulse noise protection requirement. This flag shall have the same value for all the bearers of one line in the same direction. |
| T/F vdsl2LConfProfForceInpUs | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65566 | TruthValue | read-create | This parameter indicates that the framer settings of the bearer shall be selected such that the impulse noise protection computed according to the formula specified in the relevant Recommendation is greater or equal to the minimal impulse noise protection requirement. This flag shall have the same value for all the bearers of one line in the same direction. |
| U32 vdsl2LConfProfAeleMode | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65567 | Unsigned32 | read-create | This parameter defines the UPBO electrical length estimation mode to be used in the Alternative Electrical Length Estimation method (ELE-M1) in 7.2.1.3.2.2/G.993.2. The value of this parameter is 0, 1, 2 or 3. 0-ELE-M0, 1-ELE-DS, 2-ELE-PB, 3-ELE-MIN |
| U32 vdsl2LConfProfUpboElmt | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65568 | Unsigned32 | read-create | This parameter defines the UPBO electrical length minimum threshold percentile in percent used in the Alternative Electrical Length Estimation method (ELE-M1) in clause 7.2.1.3.2.2/G.993.2. It is set by network management via the CO-MIB. The parameter ranges from 0 to 15 percent in steps of 1 percent. This value is communicated to the VTU-R via G.994.1 at start-up. |
| U32 vdsl2LconfProfUpboKlAuto | 1.3.6.1.4.1.2011.6.115.1.5.1.2.1.65569 | Unsigned32 | read-create | This parameter defines the mode in which kl0 is computed when vdsl2LconfProfUpboKlf is auto. Options: 1--max(kl0-CO,kl0-CPE) 2--min(kl0-CO,kl0-CPE) 3--kl0-CO 4--kl0-CPE 4294967295--Invalid value |
| vdsl2LineConfProfModeSpecTable | 1.3.6.1.4.1.2011.6.115.1.5.1.3 | not-accessible | The table vdsl2LineConfProfModeSpecTable extends the VDSL2 line configuration profile by VDSL Mode Specific parameters. A row in this table that has an index of vdsl2LconfProfVdslMode == defMode(1), is called a 'mandatory' row. A row in this table that has an index such that vdsl2LconfProfVdslMode is not equal to defMode(1), is called an 'optional' row. When a row in the vdsl2LineConfProfTable table (the parent row) is created, the SNMP agent will automatically create a 'mandatory' row in this table. When the parent row is deleted, the SNMP agent will automatically delete all associated rows in this table. Any attempt to delete the 'mandatory' row using the vdsl2LConfProfModeSpecRowStatus attribute will be rejected by the SNMP agent. The manager MAY create an 'optional' row in this table using the vdsl2LConfProfModeSpecRowStatus attribute if the parent row exists. The manager MAY delete an 'optional' row in this table using the vdsl2LConfProfModeSpecRowStatus attribute at any time. If the actual transmission mode of a DSL line does not match one of the 'optional' rows in this table, then the line will use the PSD configuration from the 'mandatory' row. The indexes of this table are vdsl2LConfProfProfileName and vdsl2LconfProfVdslMode. | |
| vdsl2LineConfProfModeSpecEntry | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1 | not-accessible | The table vdsl2LineConfProfModeSpecTable extends the VDSL2 line configuration profile by VDSL Mode Specific parameters. A row in this table that has an index of vdsl2LconfProfVdslMode == defMode(1), is called a 'mandatory' row. A row in this table that has an index such that vdsl2LconfProfVdslMode is not equal to defMode(1), is called an 'optional' row. When a row in the vdsl2LineConfProfTable table (the parent row) is created, the SNMP agent will automatically create a 'mandatory' row in this table. When the parent row is deleted, the SNMP agent will automatically delete all associated rows in this table. Any attempt to delete the 'mandatory' row using the vdsl2LConfProfModeSpecRowStatus attribute will be rejected by the SNMP agent. The manager MAY create an 'optional' row in this table using the vdsl2LConfProfModeSpecRowStatus attribute if the parent row exists. The manager MAY delete an 'optional' row in this table using the vdsl2LConfProfModeSpecRowStatus attribute at any time. If the actual transmission mode of a DSL line does not match one of the 'optional' rows in this table, then the line will use the PSD configuration from the 'mandatory' row. The indexes of this entry are vdsl2LConfProfProfileName and vdsl2LconfProfVdslMode. | |
| VDS vdsl2LconfProfVdslMode | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.1 | Vdsl2OperationModes | not-accessible | The VDSL Mode is a way of categorizing the various VDSL transmission modes into groups, each group (VDSL Mode) shares the same PSD configuration. There should be multiple entries in this table for a given line profile in case multiple bits are set in vdsl2LConfProfXtuTransSysEna for that profile. |
| I32 vdsl2LConfProfMaxNomPsdDs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.2 | Integer32 | read-create | The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz). Unit: 0.1 dBm/Hz |
| I32 vdsl2LConfProfMaxNomPsdUs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.3 | Integer32 | read-create | The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz). Unit: 0.1 dBm/Hz |
| U32 vdsl2LConfProfMaxNomAtpDs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.4 | Unsigned32 | read-create | The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Unit: 0.1 dBm |
| U32 vdsl2LConfProfMaxNomAtpUs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.5 | Unsigned32 | read-create | The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Unit: 0.1 dBm |
| I32 vdsl2LConfProfMaxAggRxPwrUs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.6 | Integer32 | read-create | The maximum upstream aggregate receive power over the relevant set of sub-carriers. The xTU-C should verify that the upstream power cutback is such that this maximum aggregate receive power value is honored. It ranges from -255 to 255 units of 0.1 dBm (physical values are -25.5 to 25.5 dBm). A value of all means that there is no limit. Unit: 0.1 dBm |
| VDS vdsl2LConfProfPsdMaskDs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.7 | Vdsl2PsdMaskDs | read-create | This configuration parameter defines the downstream PSD mask applicable at the U C2 reference point. This MIB PSD mask may impose PSD restrictions in addition to the Limit PSD mask defined in the relevant Recommendation (e.g., G.992.5, G.993.2). This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0xff. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup. |
| VDS vdsl2LConfProfPsdMaskUs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.8 | Vdsl2PsdMaskUs | read-create | This configuration parameter defines the upstream PSD mask applicable at the U R2 reference point. This MIB PSD mask may impose PSD restrictions in addition to the Limit PSD mask defined in the relevant Recommendations (e.g., ITU-T Recommendations G.992.3, G.993.2). This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 45-47 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCus - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup. |
| U32 vdsl2LConfProfPsdMaskSelectUs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.9 | Unsigned32 | read-create | The selected upstream PSD mask. This parameter is used only for annexes J and M of G.992.3 and G.992.5, and the same selection is used for all relevant enabled bits in vdsl2LConfProfXtuTransSysEna. The value is defined as below: 0-Invalid value 1-ADLU-32/EU-32 2-ADLU-36/EU-36 3-ADLU-40/EU-40 4-ADLU-44/EU-44 5-ADLU-48/EU-48 6-ADLU-52/EU-52 7-ADLU-56/EU-56 8-ADLU-60/EU-60 9-ADLU-64/EU-64 |
| VDS vdsl2LConfProfPSDClassMask | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.10 | Vdsl2PSDClassMask | read-create | In order to reduce the number of configuration possibilities, the limit PSD masks are grouped in the following PSD mask classes: - Class 998 Annex A: D-32, D-64. - Class 997-M1c Annex B: 997-M1c-A-7. - Class 997-M1x Annex B: 997-M1x-M-8, 997-M1x-M. - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M. - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0. - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0. - Class HPE17 Annex B: HPE17-M1-NUS0. - Class HPE30 Annex B: HPE30-M1-NUS0. - Class 997E17-M2x Annex B: 997E17-M2x-NUS0. - Class 997E30-M2x Annex B: 997E30-M2x-NUS0. - Class 998E17-M2x Annex B: 998E17-M2x-NUS0, 998E17-M2x-NUS0-M, 998E17-M2x-A. - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B. - Class 998E30-M2x Annex B: 998E30-M2x-NUS0, 998E30-M2x-NUS0-M. - Class 998ADE30-M2x Annex B: 998ADE30-M2x-NUS0-M, 998ADE30-M2x-NUS0-A. |
| VDS vdsl2LConfProfProfiles | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.11 | Vdsl2Profiles | read-create | This configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line. |
| VDS vdsl2LConfProfBandOptUsage | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.12 | Vdsl2BandOptUsage | read-create | Defines the VDSL link use of the optional frequency range [25kHz - 138kHz] (Opt). Options: 1. unused(1) - indicates Opt is unused 2. used(2) - indicates Opt usage is for upstream Huawei defined. |
| ROW vdsl2LConfProfModeSpecRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.13 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated templates. |
| VDS hwVdsl2ConfProfVirtualNoiseModeDs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.65535 | Vdsl2VirtualNoise | read-create | This parameter enables the transmitter referred virtual noise in the downstream direction. If set to 1, the virtual noise is disabled. If set to 2, the virtual noise is enabled. |
| VDS hwVdsl2ConfProfVirtualNoiseModeUs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.65536 | Vdsl2VirtualNoise | read-create | This parameter enables the transmitter referred virtual noise in the upstream direction. If set to 1, the virtual noise is disabled. If set to 2, the virtual noise is enabled. |
| VDS hwVdsl2ConfProfVirtualNoiseDs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.65537 | Vdsl2VirtualNoiseDs | read-create | This configuration parameter defines the downstream transmitter referred virtual noise (TXREFVNds). The TXREFVNds shall be specified through a set of breakpoints. Each breakpoint shall consist of a subcarrier index, with a subcarrier spacing of 4.3125 kHz, and a noise PSD level (expressed in dBm/Hz) at that subcarrier. The set of breakpoints can then be represented as [(t1, PSD1), (t2, PSD2),..., (tN, PSDN)]. The subcarrier index shall be coded as an unsigned integer. The noise level shall be coded as an 8-bit unsigned integer representing the noise level -40 dBm/Hz (coded as 0) to -140 dBm/Hz (coded as 200), in steps of 0.5 dBm/Hz. Values from 201 to 255 are special values indicating a noise level of 0 W/Hz. The maximum number of breakpoints is 32. |
| VDS hwVdsl2ConfProfVirtualNoiseUs | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.65538 | Vdsl2VirtualNoiseUs | read-create | This configuration parameter defines the upstream transmitter referred virtual noise (TXREFVNus). The TXREFVNus shall be specified through a set of breakpoints. Each breakpoint shall consist of a subcarrier index t, with a subcarrier spacing of 4.3125 kHz, and a noise PSD level (expressed in dBm/Hz) at that subcarrier. The set of breakpoints can then be represented as [(t1, PSD1), (t2, PSD2), ... , (tN, PSDN)]. The subcarrier index shall be coded as an unsigned integer. The noise level shall be coded as an 8-bit unsigned integer representing the noise level -40 dBm/Hz (coded as 0) to -140 dBm/Hz (coded as 200), in steps of 0.5 dBm/Hz. Values from 201 to 255 are special values indicating a noise level of 0 W/Hz. The maximum number of breakpoints is 16. |
| VDS hwVdsl2ConfProfAutoProfile | 1.3.6.1.4.1.2011.6.115.1.5.1.3.1.65539 | Vdsl2AutoProfile | read-create | Enable or disable the G.993.2 profiles adaptive function. If set to 1, the G.993.2 profiles adaptive function is disabled. If set to 2, the G.993.2 profiles adaptive function is enabled. |
| vdsl2ProfileChannel | 1.3.6.1.4.1.2011.6.115.1.5.2 | |||
| vdsl2ChConfProfileTable | 1.3.6.1.4.1.2011.6.115.1.5.2.1 | not-accessible | The table vdsl2ChConfProfileTable contains VDSL2 channel profile configuration. The index of this table is vdsl2ChConfProfProfileName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| vdsl2ChConfProfileEntry | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1 | not-accessible | The table vdsl2ChConfProfileTable contains VDSL2 channel profile configuration. The index of this entry is vdsl2ChConfProfProfileName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| OCT vdsl2ChConfProfProfileName | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| U32 vdsl2ChConfProfMinDataRateDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.2 | Unsigned32 | read-create | If retransmission is not used in downstream direction,this parameter specifics minimum data rate for the bearer channel on downstream direction. The rate is coded in steps of 1000 bit/s. Unit: bits/second |
| U32 vdsl2ChConfProfMinDataRateUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.3 | Unsigned32 | read-create | If retransmission is not used in upstream direction,this parameter specifics minimum data rate for the bearer channel on upstream direction. The rate is coded in steps of 1000 bit/s Unit: bits/second |
| U32 vdsl2ChConfProfMinResDataRateDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.4 | Unsigned32 | read-create | Minimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., Vdsl2LineConfRaModeDs) is set to DynamicRa. Unit: bits/second |
| U32 vdsl2ChConfProfMinResDataRateUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.5 | Unsigned32 | read-create | Minimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., Vdsl2LineConfRaModeUs) is set to DynamicRa. Unit: bits/second |
| U32 vdsl2ChConfProfMaxDataRateDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.6 | Unsigned32 | read-create | If retransmission is not used in downstream direction,this parameter specifics maximum data rate for the bearer channel on downstream direction. The rate is coded in steps of 1000 bit/s. Unit: bits/second |
| U32 vdsl2ChConfProfMaxDataRateUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.7 | Unsigned32 | read-create | If retransmission is not used in upstream direction,this parameter specifics maximum data rate for the bearer channel on upstream direction. The rate is coded in steps of 1000 bit/s. Unit: bits/second |
| U32 vdsl2ChConfProfMinDataRateLowPwrDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.8 | Unsigned32 | read-create | Minimum Data Rate in Low Power state on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s, during the low power state (L1 in G.992.2, L2 in G.992.3). Unit: bits/second |
| U32 vdsl2ChConfProfMinDataRateLowPwrUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.9 | Unsigned32 | read-create | Minimum Data Rate in Low Power state on Upstream direction. The minimum net data rate for the bearer channel, coded in bit/s, during the low power state (L1 in G.992.2, L2 in G.992.3). Unit: bits/second |
| U32 vdsl2ChConfProfMaxDelayDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.10 | Unsigned32 | read-create | If retransmission is not used in downstream direction,this parameter is maximum interleave delay on downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Vdsl2ChanStatusActDelay) is as close as possible to, but less than or equal to, Vdsl2ChanConfMaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Unit: milliseconds |
| U32 vdsl2ChConfProfMaxDelayUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.11 | Unsigned32 | read-create | If retransmission is not used in upstream direction,this parameter is maximum interleave delay on upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Vdsl2ChanStatusActDelay) is as close as possible to, but less than or equal to, Vdsl2ChanConfMaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Unit: milliseconds |
| VDS vdsl2ChConfProfMinProtectionDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.12 | Vdsl2SymbolProtectionDs | read-create | If retransmission is not used in downstream direction,this parameter is minimum impulse noise protection for the bearer channel on downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Unit: symbols |
| VDS vdsl2ChConfProfMinProtectionUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.13 | Vdsl2SymbolProtectionUs | read-create | If retransmission is not used in upstream direction,this parameter is minimum impulse noise protection for the bearer channel on upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Unit: symbols |
| VDS vdsl2ChConfProfMaxBerDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.14 | Vdsl2MaxBer | read-create | Maximum Bit Error Ratio on Downstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-5 or 1E-7). Options: 1. eminus3 (1) - 1E-3 2. eminus5 (2) - 1E-5 3. eminus7 (3) - 1E-7 |
| VDS vdsl2ChConfProfMaxBerUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.15 | Vdsl2MaxBer | read-create | Maximum Bit Error Ratio on Upstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-5 or 1E-7). Options: 1. eminus3 (1) - 1E-3 2. eminus5 (2) - 1E-5 3. eminus7 (3) - 1E-7 |
| U32 vdsl2ChConfProfUsDataRateDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.16 | Unsigned32 | read-create | If retransmission is not used in downstream direction,this parameter is data rate threshold upshift for downstream direction. An 'Up-shift rate change' event is triggered when the actual downstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bit/s. Unit: bits/second |
| U32 vdsl2ChConfProfDsDataRateDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.17 | Unsigned32 | read-create | If retransmission is not used in downstream direction,this parameter is data rate threshold downshift for downstream direction. A 'Down-shift rate change' event is triggered when the actual downstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bit/s. Unit: bits/second |
| U32 vdsl2ChConfProfUsDataRateUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.18 | Unsigned32 | read-create | If retransmission is not used in upstream direction,this parameter is data rate threshold up shift for upstream direction. An 'Up-shift rate change' event is triggered when the actual upstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bit/s. Unit: bits/second |
| U32 vdsl2ChConfProfDsDataRateUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.19 | Unsigned32 | read-create | If retransmission is not used in upstream direction,this parameter is data rate threshold downshift for upstream direction. A 'Down-shift rate change' event is triggered when the actual upstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bit/s. Unit: bits/second |
| T/F vdsl2ChConfProfImaEnabled | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.20 | TruthValue | read-create | IMA Mode Enable. The parameter enables the IMA operation mode in the ATM Data Path. Relevant only if the channel is of ATM Data Path. When in 'enable' state, the ATM data path should comply with the requirements for IMA transmission. |
| VDS vdsl2ChConfProfDataPathMode | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.21 | Vdsl2DataPathMode | read-create | The channel data path mode. Options: 1. atm(1) - ATM 2. ptm(2) - PTM 3. both(3) - ATM and PTM Huawei defined. |
| ROW vdsl2ChConfProfRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.22 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated templates. |
| VDS vdsl2ChConfProfPhyRcontrolDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.23 | Vdsl2PhyRControl | read-create | To enable or disable the retransmission function. |
| VDS vdsl2ChConfProfPhyRcontrolUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.24 | Vdsl2PhyRControl | read-create | To enable or disable the retransmission function. |
| VDS vdsl2ChConfProfInpMaxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.25 | Vdsl2SymbolProtectionDs | read-create | Maximum Impulse Noise Protection on downstream direction. |
| VDS vdsl2ChConfProfInpMaxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.26 | Vdsl2SymbolProtectionDs | read-create | Maximum Impulse Noise Protection on upstream direction. |
| U32 vdsl2ChConfProfMinRtxRatioDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.27 | Unsigned32 | read-create | This object is used to config the minimum retransmission band width parameter downstream. |
| U32 vdsl2ChConfProfMinRtxRatioUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.28 | Unsigned32 | read-create | This object is used to config the minimum retransmission band width parameter upstream. |
| U32 vdsl2ChConfProfMinRSoverheadDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.29 | Unsigned32 | read-create | This object is used to config the minimum RSoverhead parameter downstream.. |
| U32 vdsl2ChConfProfMinRSoverheadUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.30 | Unsigned32 | read-create | This object is used to config the minimum RSoverhead parameter upstream.. |
| VDS vdsl2ChConfProfErasureDecoding | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.31 | Vdsl2ProfSwitchType | read-create | To enable or disable the erasure decoding of a channel. Options: 1. enable(1) 2. disable(2) |
| U32 vdsl2ChConfProfMinSosBrDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.32 | Unsigned32 | read-create | This parameter specifies the minimum net data rate required for a valid SOS request in the downstream direction. The valid range of values is from 0 to 524280Kbps in steps of 8Kbps. Unit: 8Kbps |
| U32 vdsl2ChConfProfMinSosBrUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.33 | Unsigned32 | read-create | This parameter specifies the minimum net data rate required for a valid SOS request in the upstream direction.The valid range of values is from 0 to 524280Kbps in steps of 8Kbps. Unit: 8Kbps |
| U32 vdsl2ChConfProfMinEtrRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.34 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum expected throughput for the bearer channel.The values range in steps of 1000 bit/s. |
| U32 vdsl2ChConfProfMinEtrRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.35 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum expected throughput for the bearer channel.The values range in steps of 1000 bit/s. |
| U32 vdsl2ChConfProfMaxEtrRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.36 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the maximum expected throughput for the bearer channel.The values range in steps of 1000 bit/s. |
| U32 vdsl2ChConfProfMaxEtrRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.37 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the maximum expected throughput for the bearer channel.The values range in steps of 1000 bit/s. |
| U32 vdsl2ChConfProfMaxNdrRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.38 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the maximum net data rate for the bearer channel. The values range in steps of 1000 bit/s. |
| U32 vdsl2ChConfProfMaxNdrRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.39 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the maximum net data rate for the bearer channel.The values range in steps of 1000 bit/s. |
| U32 vdsl2ChConfProfMaxDelayRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.40 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the maximum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 1 to 63 ms by steps of 1 ms. Unit: milliseconds |
| U32 vdsl2ChConfProfMaxDelayRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.41 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the maximum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 1 to 63 ms by steps of 1 ms. Unit: milliseconds |
| U32 vdsl2ChConfProfMinDelayRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.42 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 0 to 63 ms by steps of 1 ms. Unit: milliseconds |
| U32 vdsl2ChConfProfMinDelayRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.43 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 0 to 63 ms by steps of 1 ms. Unit: milliseconds |
| U32 vdsl2ChConfProfMinInpShineRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.44 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 63, inclusive. Unit: symbols |
| U32 vdsl2ChConfProfMinInpShineRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.45 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 63, inclusive. Unit: symbols |
| U32 vdsl2ChConfProfMinInp8ShineRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.46 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 127, inclusive. Unit: symbols |
| U32 vdsl2ChConfProfMinInp8ShineRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.47 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 127, inclusive. Unit: symbols |
| U32 vdsl2ChConfProfShineRatioRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.48 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the SHINE ratio (detailed definition see G.998.4). The values range from 0 to 0.100 in increments of 0.001. |
| U32 vdsl2ChConfProfShineRatioRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.49 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the SHINE ratio (detailed definition see G.998.4). The values range from 0 to 0.100 in increments of 0.001. |
| U32 vdsl2ChConfProfMinInpReinRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.50 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 7, inclusive. |
| U32 vdsl2ChConfProfMinInpReinRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.51 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 7, inclusive. |
| U32 vdsl2ChConfProfMinInp8ReinRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.52 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 13, inclusive. |
| U32 vdsl2ChConfProfMinInp8ReinRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.53 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 13, inclusive. |
| INT vdsl2ChConfProfIatReinRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.54 | INTEGER | read-create | If retransmission is used in downstream direction, this parameter specifies the inter-arrival time that shall be assumed for REIN protection. Options: 1. frequency100Hz(0) - an inter-arrival time derived from a REIN at 100 Hz 2. frequency120Hz(1) - an inter-arrival time derived from a REIN at 120 Hz |
| INT vdsl2ChConfProfIatReinRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.55 | INTEGER | read-create | If retransmission is used in upstream direction, this parameter specifies the inter-arrival time that shall be assumed for REIN protection. Options: 1. frequency100Hz(0) - an inter-arrival time derived from a REIN at 100 Hz 2. frequency120Hz(1) - an inter-arrival time derived from a REIN at 120 Hz |
| INT vdsl2ChConfProfInitPolicy | 1.3.6.1.4.1.2011.6.115.1.5.2.1.1.56 | INTEGER | read-create | This parameter indicates which policy shall be applied to determine the transceiver configuration parameters at initialization. The valid values for CIPOLICY are 0,1 and 2. Those policies are defined in the respective recommendations. Options: 1. policy0 (1) - Policy 0 according to the applicable standard 2. policy1 (2) - Policy 1 according to the applicable standard 3. policy2 (3) - Policy 2 according to the applicable standard |
| vdsl2ProfileAlarmConf | 1.3.6.1.4.1.2011.6.115.1.5.3 | |||
| vdsl2LineAlarmConfTemplateTable | 1.3.6.1.4.1.2011.6.115.1.5.3.1 | not-accessible | The table vdsl2LineAlarmConfTemplateTable contains VDSL2 line alarm configuration template. The index of this table is vdsl2LAlarmConfTempTemplateName. A default template with an index of 'DEFVAL' will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| vdsl2LineAlarmConfTemplateEntry | 1.3.6.1.4.1.2011.6.115.1.5.3.1.1 | not-accessible | The table vdsl2LineAlarmConfTemplateTable contains VDSL2 line alarm configuration template. The index of this entry is vdsl2LAlarmConfTempTemplateName. A default template with an index of 'DEFVAL' will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| OCT vdsl2LAlarmConfTempTemplateName | 1.3.6.1.4.1.2011.6.115.1.5.3.1.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| OCT vdsl2LAlarmConfTempLineProfile | 1.3.6.1.4.1.2011.6.115.1.5.3.1.1.2 | OCTET STRING | read-create | The value of this object identifies the row in the VDSL2 Line Thresholds Configuration Profile Table (vdsl2LineAlarmConfProfileTable) that applies to this VDSL2 line. |
| OCT vdsl2LAlarmConfTempChan1ConfProfile | 1.3.6.1.4.1.2011.6.115.1.5.3.1.1.3 | OCTET STRING | read-create | The value of this object identifies the row in the VDSL2 Channel Thresholds Configuration Profile Table (vdsl2ChAlarmConfProfileTable) that applies for VDSL2 bearer channel #1. The channel profile name specified here must match the name of an existing row in the vdsl2ChAlarmConfProfileTable table. |
| OCT vdsl2LAlarmConfTempChan2ConfProfile | 1.3.6.1.4.1.2011.6.115.1.5.3.1.1.4 | OCTET STRING | read-create | The value of this object identifies the row in the VDSL2 Channel Thresholds Configuration Profile Table (vdsl2ChAlarmConfProfileTable) that applies for VDSL2 bearer channel #2. The channel profile name specified here must match the name of an existing row in the vdsl2ChAlarmConfProfileTable table. If the channel is unused, then the object is set to a zero length string. |
| OCT vdsl2LAlarmConfTempChan3ConfProfile | 1.3.6.1.4.1.2011.6.115.1.5.3.1.1.5 | OCTET STRING | read-create | The value of this object identifies the row in the VDSL2 Channel Thresholds Configuration Profile Table (vdsl2ChAlarmConfProfileTable) that applies for VDSL2 bearer channel #3. The channel profile name specified here must match the name of an existing row in the vdsl2ChAlarmConfProfileTable table. This object may be set to a non-zero length string only if vdsl2LAlarmConfTempChan2ConfProfile contains a non-zero length string. |
| OCT vdsl2LAlarmConfTempChan4ConfProfile | 1.3.6.1.4.1.2011.6.115.1.5.3.1.1.6 | OCTET STRING | read-create | The value of this object identifies the row in the VDSL2 Channel Thresholds Configuration Profile Table (vdsl2ChAlarmConfProfileTable) that applies for VDSL2 bearer channel #4. The channel profile name specified here must match the name of an existing row in the vdsl2ChAlarmConfProfileTable table. This object may be set to a non-zero length string only if vdsl2LAlarmConfTempChan3ConfProfile contains a non-zero length string. |
| ROW vdsl2LAlarmConfTempRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.3.1.1.7 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated lines. |
| vdsl2LineAlarmConfProfileTable | 1.3.6.1.4.1.2011.6.115.1.5.3.2 | not-accessible | The table vdsl2LineAlarmConfProfileTable contains VDSL2 line PM thresholds profiles. The index of this table is vdsl2LineAlarmConfProfileName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| vdsl2LineAlarmConfProfileEntry | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1 | not-accessible | The table vdsl2LineAlarmConfProfileTable contains VDSL2 line PM thresholds profiles. The index of this entry is vdsl2LineAlarmConfProfileName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor specific values, unless otherwise specified in this document. | |
| OCT vdsl2LineAlarmConfProfileName | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| NUM vdsl2LineAlarmConfProfileXtucThresh15MinFecs | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.2 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MFecs counter, when vdsl2PMLCurrUnit is XTUC {1}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| NUM vdsl2LineAlarmConfProfileXtucThresh15MinEs | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.3 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MEs counter, when vdsl2PMLCurrUnit is XTUC {1}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| NUM vdsl2LineAlarmConfProfileXtucThresh15MinSes | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.4 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MSes counter, when vdsl2PMLCurrUnit is XTUC {1}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| NUM vdsl2LineAlarmConfProfileXtucThresh15MinLoss | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.5 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MLoss counter, when vdsl2PMLCurrUnit is XTUC {1}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| NUM vdsl2LineAlarmConfProfileXtucThresh15MinUas | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.6 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MUas counter, when vdsl2PMLCurrUnit is XTUC {1}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| NUM vdsl2LineAlarmConfProfileXturThresh15MinFecs | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.7 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MFecs counter, when vdsl2PMLCurrUnit is XTUR {2}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| NUM vdsl2LineAlarmConfProfileXturThresh15MinEs | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.8 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MEs counter, when vdsl2PMLCurrUnit is XTUR {2}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| NUM vdsl2LineAlarmConfProfileXturThresh15MinSes | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.9 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MSes counter, when vdsl2PMLCurrUnit is XTUR {2}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| NUM vdsl2LineAlarmConfProfileXturThresh15MinLoss | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.10 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MLoss counter, when vdsl2PMLCurrUnit is XTUR {2}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| NUM vdsl2LineAlarmConfProfileXturThresh15MinUas | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.11 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MUas counter, when vdsl2PMLCurrUnit is XTUR {2}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| U32 vdsl2LineAlarmConfProfileThresh15MinFailedFullInt | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.12 | Unsigned32 | read-create | A threshold for the vdsl2PMLCurrInit15MfailedFullInits counter. The value 0 means that no threshold is specified for the associated counter. |
| U32 vdsl2LineAlarmConfProfileThresh15MinFailedShrtInt | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.13 | Unsigned32 | read-create | A threshold for the vdsl2PMLCurrInit15MFailedShortInits counter. The value 0 means that no threshold is specified for the associated counter. |
| ROW vdsl2LineAlarmConfProfileRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.14 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated templates. |
| U32 vdsl2LineAlarmConfProfileThresh15MinFullInt | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.15 | Unsigned32 | read-create | A threshold for the vdsl2PMLCurrInit15MFullInits counter. The value 0 means that no threshold is specified for the associated counter. |
| NUM vdsl2LineAlarmConfProfileXtucThresh15MinLeftrs | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.16 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MLeftrs counter, when vdsl2PMLCurrUnit is XTUC {1}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| NUM vdsl2LineAlarmConfProfileXturThresh15MinLeftrs | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.17 | HCPerfIntervalThreshold | read-create | A threshold for the vdsl2PMLCurr15MLeftrs counter, when vdsl2PMLCurrUnit is XTUR {2}. The value 0 means that no threshold is specified for the associated counter. Unit: seconds |
| INT hwVdsl2LineAlarmConfProfileDyingGaspAlarmSwitch | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.18 | INTEGER | read-create | This object enable/disable the report of LOSS-OF-POWER alarm in a VDSL line. Options: 1. enable(1) - The report of LOSS-OF-POWER alarm in a VDSL line is enabled 2. disable(2) - The report of LOSS-OF-POWER alarm in a VDSL line is disabled |
| INT hwVdsl2LineAlarmConfProfileActiveFailAlarmSwitch | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.19 | INTEGER | read-create | This object enable/disable the active fail alarm switch. Options: 1. enable(1) - The active fail alarm switch is enabled 2. disable(2) - The active fail alarm switch is disabled |
| INT hwVdsl2LineAlarmConfProfileRateChangeAlarmSwitch | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.20 | INTEGER | read-create | This object enable/disable the active rate change alarm switch. Options: 1. enable(1) - The active rate change alarm switch is enabled 2. disable(2) - The active rate change alarm switch is disabled |
| INT hwVdsl2LineAlarmConfProfileLegacyCpeAlarmSwitch | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.21 | INTEGER | read-create | This object enable/disable the legacy cpe alarm switch. Options: 1. enable(1) - The legacy cpe alarm switch is enabled 2. disable(2) - The legacy cpe alarm switch is disabled |
| INT hwVdsl2LineAlarmConfProfileVictAbnormalVariationAlarmSwitch | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.22 | INTEGER | read-create | This object enable/disable alarm switch that the port receives abnormal crosstalk. Options: 1. enable(1) - The alarm switch that the port receives abnormal crosstalk is enabled 2. disable(2) - The alarm switch that the port receives abnormal crosstalk is disabled |
| INT hwVdsl2LineAlarmConfProfileDistAbnormalVariationAlarmSwitch | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.23 | INTEGER | read-create | This object enable/disable the alarm switch that the port causes abnormal crosstalk. Options: 1. enable(1) - The alarm switch that the port causes abnormal crosstalk is enabled 2. disable(2) - The alarm switch that the port causes abnormal crosstalk is disabled |
| INT hwVdsl2LineAlarmConfProfileReceivedESAbnormalAlarmSwitch | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.24 | INTEGER | read-create | This object enable/disable the alarm switch that The port receives abnormal error sample messages. Options: 1. enable(1) - The alarm switch that the port receives abnormal error sample messages is enabled 2. disable(2) - The alarm switch that the port receives abnormal error sample messages is disabled |
| INT hwVdsl2LineAlarmConfProfileNonVectoringCPEActivatedAlarmSwitch | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.25 | INTEGER | read-create | This object enable/disable the alarm switch that the port is activated in none-vectoring mode. Options: 1. enable(1) - The alarm switch that the port is activated in none-vectoring mode is enabled 2. disable(2) - The alarm switch that the port is activated in none-vectoring mode is disabled |
| INT hwVdsl2LineAlarmConfProfileFreqRetrainReachThresholdAlarmSwitch | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.26 | INTEGER | read-create | This object enable/disable the alarm switch that the port frequently retrain times in 15 minutes reach the threshold. Options: 1. enable(1) - The alarm switch that the port frequently retrain times in 15 minutes reach the threshold is enabled 2. disable(2) - The alarm switch that the port frequently retrain times in 15 minutes reach the threshold is disabled |
| INT hwvdsl2LineAlarmConfProfilePSConfigAbnormalAlarmSwitch | 1.3.6.1.4.1.2011.6.115.1.5.3.2.1.27 | INTEGER | read-create | This object enable/disable the pilot sequence configuration abnormal alarm switch. Options: 1. enable(1) - The pilot sequence configuration abnormal alarm switch is enabled 2. disable(2) - The pilot sequence configuration abnormal alarm switch is disabled |
| vdsl2ChAlarmConfProfileTable | 1.3.6.1.4.1.2011.6.115.1.5.3.3 | not-accessible | The table vdsl2ChAlarmConfProfileTable contains VDSL2 channel PM thresholds profiles. The index of this table is vdsl2ChAlarmConfProfileName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| vdsl2ChAlarmConfProfileEntry | 1.3.6.1.4.1.2011.6.115.1.5.3.3.1 | not-accessible | The table vdsl2ChAlarmConfProfileTable contains VDSL2 channel PM thresholds profiles. The index of this entry is vdsl2ChAlarmConfProfileName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| OCT vdsl2ChAlarmConfProfileName | 1.3.6.1.4.1.2011.6.115.1.5.3.3.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| U32 vdsl2ChAlarmConfProfileXtucThresh15MinCodingViolations | 1.3.6.1.4.1.2011.6.115.1.5.3.3.1.2 | Unsigned32 | read-create | A threshold for the vdsl2PMChCurr15MCodingViolations counter, when vdsl2PMChCurrUnit is XTUC {1}. The value 0 means that no threshold is specified for the associated counter. |
| U32 vdsl2ChAlarmConfProfileXtucThresh15MinCorrected | 1.3.6.1.4.1.2011.6.115.1.5.3.3.1.3 | Unsigned32 | read-create | A threshold for the vdsl2PMChCurr15MCorrectedBlocks counter, when vdsl2PMChCurrUnit is XTUC {1}. The value 0 means that no threshold is specified for the associated counter. |
| U32 vdsl2ChAlarmConfProfileXturThresh15MinCodingViolations | 1.3.6.1.4.1.2011.6.115.1.5.3.3.1.4 | Unsigned32 | read-create | A threshold for the vdsl2PMChCurr15MCodingViolations counter, when vdsl2PMChCurrUnit is XTUR {2}. The value 0 means that no threshold is specified for the associated counter. |
| U32 vdsl2ChAlarmConfProfileXturThresh15MinCorrected | 1.3.6.1.4.1.2011.6.115.1.5.3.3.1.5 | Unsigned32 | read-create | A threshold for the vdsl2PMChCurr15MCorrectedBlocks counter, when vdsl2PMChCurrUnit is XTUR {2}. The value 0 means that no threshold is specified for the associated counter. |
| U32 vdsl2ChAlarmConfProfileMonitoringRateDs | 1.3.6.1.4.1.2011.6.115.1.5.3.3.1.6 | Unsigned32 | read-create | The channel monitoring rate downstream. Huawei defined. When the value you set is larger than the value of the rate downstream defined in the channel profile, it will not be successful. The value 0 means that no threshold is specified for the associated counter. Unit: bits/second |
| U32 vdsl2ChAlarmConfProfileMonitoringRateUs | 1.3.6.1.4.1.2011.6.115.1.5.3.3.1.7 | Unsigned32 | read-create | The channel monitoring rate upstream. Huawei defined. When the value you set is larger than the value of the rate upstream defined in the channel profile, it will not be successful. The value 0 means that no threshold is specified for the associated counter. Unit: bits/second |
| ROW vdsl2ChAlarmConfProfileRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.3.3.1.8 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated templates. |
| vdsl2ProfileTIMode | 1.3.6.1.4.1.2011.6.115.1.5.4 | |||
| vdsl2ServProfTable | 1.3.6.1.4.1.2011.6.115.1.5.4.1 | not-accessible | The table vdsl2ServProfTable contains xDSL line service configuration. The index of this table is vdsl2ServProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| vdsl2ServProfEntry | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1 | not-accessible | The table vdsl2ServProfTable contains xDSL line service configuration. The index of this entry is vdsl2ServProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| OCT vdsl2ServProfName | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| VDS vdsl2ServProfDataPathMode | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.2 | Vdsl2DataPathModeType | read-create | This parameter indicates the VDSL2 line data path modes. Options: 1. atm (1) - atm mode 2. ptm (2) - ptm mode |
| VDS vdsl2ServProfBitSwapEnablingDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.3 | Vdsl2ProfSwitchType | read-create | Enables or disables the bit swap downstream of a line. Options: 1. enable(1) - Enable the bit swap downstream of a line 2. disable(2) - Disable the bit swap downstream of a line huawei defined. |
| VDS vdsl2ServProfBitSwapEnablingUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.4 | Vdsl2ProfSwitchType | read-create | Enables or disables the bit swap upstream of a line. Options: 1. enable(1) - Enable the bit swap upstream of a line. 2. disable(2) - Disable the bit swap upstream of a line. huawei defined. |
| VDS vdsl2ServProfRaMode | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.5 | Vdsl2RaMode | read-create | The mode of operation of a rate-adaptive xTU-R in the transmit direction. Options: 1. manual (1) - No Rate-Adaptation. The initialization process attempts to synchronize to a specified rate. 2. rainit (2) - Rate-Adaptation during initialization process only, which attempts to synchronize to a rate between minimum and maximum specified values. 3. dynamic (3) - Rate-Adaptation during show time |
| VDS vdsl2ServProfCh1Enabling | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.6 | Vdsl2ChEnabling | read-create | This parameter indicates whether the bearer 1 of VDSL2 line is enabling. Options: 1. enable(1) - Enable the bearer 1 of VDSL2 line. 2. disable(2) - Disable the bearer 1 of VDSL2 line. huawei defined. |
| U32 vdsl2ServProfCh1MinDataRateDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.7 | Unsigned32 | read-create | If retransmission is not used in downstream direction,this parameter specifics minimum data rate for the bearer channel on downstream direction. coded in bit/s. Unit: bits/second |
| U32 vdsl2ServProfCh1MinDataRateUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.8 | Unsigned32 | read-create | If retransmission is not used in upstream direction,this parameter specifics minimum data rate for the bearer channel on upstream direction. coded in bit/s. Unit: bits/second |
| U32 vdsl2ServProfCh1MinResDataRateDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.9 | Unsigned32 | read-create | Minimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode of the bearer channel (i.e., vdsl2ServProfRaMode) is set to Dynamic. Unit: bits/second |
| U32 vdsl2ServProfCh1MinResDataRateUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.10 | Unsigned32 | read-create | Minimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode of the bearer channel (i.e., vdsl2ServProfRaMode) is set to Dynamic. Unit: bits/second |
| U32 vdsl2ServProfCh1MaxDataRateDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.11 | Unsigned32 | read-create | If retransmission is not used in downstream direction,this parameter specifics maximum data rate for the bearer channel on downstream direction. coded in bit/s. Unit: bits/second |
| U32 vdsl2ServProfCh1MaxDataRateUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.12 | Unsigned32 | read-create | If retransmission is not used in upstream direction,this parameter specifics maximum data rate for the bearer channel on upstream direction. coded in bit/s. Unit: bits/second |
| U32 vdsl2ServProfCh1MinDataRateLowPwrDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.13 | Unsigned32 | read-create | Minimum Data Rate in Low Power state on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s., during the low power state (L1 in G.992.2, L2 in G.992.3). Unit: bits/second |
| U32 vdsl2ServProfCh1MinDataRateLowPwrUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.14 | Unsigned32 | read-create | Minimum Data Rate in Low Power state on Upstream direction. The minimum net data rate for the bearer channel, coded in bit/s, during the low power state (L1 in G.992.2, L2 in G.992.3). Unit: bits/second |
| U32 vdsl2ServProfCh1RaRatioDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.15 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - vdsl2ServProfCh1RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. Unit: percents |
| U32 vdsl2ServProfCh1RaRatioUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.16 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - vdsl2ServProfCh1RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. Unit: percents |
| VDS vdsl2ServProfCh2Enabling | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.17 | Vdsl2ChEnabling | read-create | This parameter indicates whether the bearer 2 of VDSL2 line is enabling. Options: 1. enable(1) - Enable the bearer 2 of VDSL2 line. 2. disable(2) - Disable the bearer 2 of VDSL2 line. huawei defined. |
| U32 vdsl2ServProfCh2MinDataRateDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.18 | Unsigned32 | read-create | Minimum Data Rate on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s. Unit: bits/second |
| U32 vdsl2ServProfCh2MinDataRateUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.19 | Unsigned32 | read-create | Minimum Data Rate on Upstream direction. The minimum net data rate for the bearer channel, coded in bit/s. Unit: bits/second |
| U32 vdsl2ServProfCh2MinResDataRateDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.20 | Unsigned32 | read-create | Minimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode of the bearer channel (i.e., vdsl2ServProfRaMode) is set to Dynamic. Unit: bits/second |
| U32 vdsl2ServProfCh2MinResDataRateUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.21 | Unsigned32 | read-create | Minimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bit/s. This parameter is used only if the Rate Adaptation Mode of the bearer channel (i.e., vdsl2ServProfRaMode) is set to Dynamic. Unit: bits/second |
| U32 vdsl2ServProfCh2MaxDataRateDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.22 | Unsigned32 | read-create | Maximum Data Rate on Downstream direction. The maximum net data rate for the bearer channel, coded in bit/s. Unit: bits/second |
| U32 vdsl2ServProfCh2MaxDataRateUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.23 | Unsigned32 | read-create | Maximum Data Rate on Upstream direction. The maximum net data rate for the bearer channel, coded in bit/s. Unit: bits/second |
| U32 vdsl2ServProfCh2MinDataRateLowPwrDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.24 | Unsigned32 | read-create | Minimum Data Rate in Low Power state on Downstream direction. The minimum net data rate for the bearer channel, coded in bit/s, during the low power state (L1 in G.992.2, L2 in G.992.3). Unit: bits/second |
| U32 vdsl2ServProfCh2MinDataRateLowPwrUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.25 | Unsigned32 | read-create | Minimum Data Rate in Low Power state on Upstream direction. The minimum net data rate for the bearer channel, coded in bit/s, during the low power state (L1 in G.992.2, L2 in G.992.3). Unit: bits/second |
| U32 vdsl2ServProfCh2RaRatioDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.26 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - vdsl2ServProfCh2RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. Unit: percents |
| U32 vdsl2ServProfCh2RaRatioUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.27 | Unsigned32 | read-create | Rate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - vdsl2ServProfCh2RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%. Unit: percents |
| ROW vdsl2ServProfRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.28 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated lines. |
| U32 hwvdsl2ServProfMinEtrRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.29 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum expected throughput for the bearer channel.The values range in steps of 1000 bit/s. |
| U32 hwvdsl2ServProfMinEtrRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.30 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum expected throughput for the bearer channel.The values range in steps of 1000 bit/s. |
| U32 hwvdsl2ServProfMaxEtrRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.31 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the maximum expected throughput for the bearer channel.The values range in steps of 1000 bit/s. |
| U32 hwvdsl2ServProfMaxEtrRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.32 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the maximum expected throughput for the bearer channel.The values range in steps of 1000 bit/s. |
| U32 hwvdsl2ServProfMaxNdrRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.33 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the maximum net data rate for the bearer channel. The values range in steps of 1000 bit/s. |
| U32 hwvdsl2ServProfMaxNdrRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.1.1.34 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the maximum net data rate for the bearer channel.The values range in steps of 1000 bit/s. |
| vdsl2SpectrumProfTable | 1.3.6.1.4.1.2011.6.115.1.5.4.2 | not-accessible | The table vdsl2SpectrumProfTable contains VDSL2 line spectrum configuration. The index of this table is vdsl2SpectrumProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| vdsl2SpectrumProfEntry | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1 | not-accessible | The table vdsl2SpectrumProfTable contains VDSL2 line spectrum configuration. The index of this entry is vdsl2SpectrumProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| OCT vdsl2SpectrumProfName | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| VDS vdsl2SpectrumProfXtuTransSysEna | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1.2 | Vdsl2TransmissionModeType | read-create | xTU Transmission System Enabling (xTSE). A list of the different coding types enabled in this profile. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the XTUs may apply the respective coding for the VDSL line. A bit set to '0' means that the XTUs cannot apply the respective coding for the VDSL line. All 'reserved' bits should be set to '0'. |
| VDS vdsl2SpectrumProfScMaskDs | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1.3 | Vdsl2ScMaskDs | read-create | Sub-carriers mask. A bitmap of 512 bits that allows masking up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCds < 512, all bits i (NSCds i <= 512) should be set to '1'. |
| VDS vdsl2SpectrumProfScMaskUs | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1.4 | Vdsl2ScMaskUs | read-create | Sub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the respective upstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCus < 64, all bits i (NSCus < i <= 64) should be set to '1'. |
| OCT vdsl2SpectrumProfVDSLtoneblackout | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1.5 | OCTET STRING | read-create | The subset of subcarriermask that shall be used to mask the subcarriers. It is a string of bands consist of begin tone index and end tone index. for example :0-10,20-50,100-4095 It can contain as most as 8 bands. |
| OCT vdsl2SpectrumProfRfiBands | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1.6 | OCTET STRING | read-create | The subset of PSD mask breakpoints that shall be used to notch an RFI band. It is a string of bands consist of begin tone index and end tone index. for example :0-10,20-50,100-4095 It can contain as most as 16 bands. |
| ROW vdsl2SpectrumProfRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1.7 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated lines. |
| INT hwvdsl2SpectrumProfRtxModeDs | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1.8 | INTEGER | read-create | The mode of operation of G.998.4 retransmission in downstream direction. Options: 1. forbidden(0) - G.998.4 retransmission not allowed. 2. preferred(1) - G.998.4 retransmission is preferred. 3. forced(2) - Force the use of the G.998.4 retransmission. 4. testmode(3) - Force the use of the G.998.4 retransmission in test mode. |
| INT hwvdsl2SpectrumProfRtxModeUs | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1.9 | INTEGER | read-create | The mode of operation of G.998.4 retransmission in upstream direction. Options: 1. forbidden(0) - G.998.4 retransmission not allowed. 2. preferred(1) - G.998.4 retransmission is preferred. 3. forced(2) - Force the use of the G.998.4 retransmission. 4. testmode(3) - Force the use of the G.998.4 retransmission in test mode. |
| U32 hwvdsl2SpectrumProfProfLeftrThreshDs | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1.10 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the threshold for declaring a near-end leftr defect. The value is coded as a fraction of the NDR with valid range from 0.01 to 0.99 with increments of 0.01. A special value means the ETR shall be used as the default threshold for declaring a leftr defect. |
| U32 hwvdsl2SpectrumProfProfLeftrThreshUs | 1.3.6.1.4.1.2011.6.115.1.5.4.2.1.11 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the threshold for declaring a near-end leftr defect. The value is coded as a fraction of the NDR with valid range from 0.01 to 0.99 with increments of 0.01. A special value means the ETR shall be used as the default threshold for declaring a leftr defect. |
| vdsl2SpectrumProfModeSpecTable | 1.3.6.1.4.1.2011.6.115.1.5.4.3 | not-accessible | The table vdsl2SpectrumProfModeSpecTable extends the VDSL2 line configuration profile by VDSL Mode Specific parameters. A row in this table that has an index of vdsl2LconfProfVdslMode == defMode(1), is called a 'mandatory' row. A row in this table that has an index such that vdsl2LconfProfVdslMode is not equal to defMode(1), is called an 'optional' row. When a row in the vdsl2LineConfProfTable table (the parent row) is created, the SNMP agent will automatically create a 'mandatory' row in this table. When the parent row is deleted, the SNMP agent will automatically delete all associated rows in this table. Any attempt to delete the 'mandatory' row using the vdsl2LConfProfModeSpecRowStatus attribute will be rejected by the SNMP agent. The manager MAY create an 'optional' row in this table using the vdsl2LConfProfModeSpecRowStatus attribute if the parent row exists. The manager MAY delete an 'optional' row in this table using the vdsl2LConfProfModeSpecRowStatus attribute at any time. If the actual transmission mode of a DSL line does not match one of the 'optional' rows in this table, then the line will use the PSD configuration from the 'mandatory' row. The indexes of this table are vdsl2SpectrumProfName and vdsl2SpectrumProfXdslMode. | |
| vdsl2SpectrumProfModeSpecEntry | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1 | not-accessible | The table vdsl2SpectrumProfModeSpecTable extends the VDSL2 line configuration profile by VDSL Mode Specific parameters. A row in this table that has an index of vdsl2LconfProfVdslMode == defMode(1), is called a 'mandatory' row. A row in this table that has an index such that vdsl2LconfProfVdslMode is not equal to defMode(1), is called an 'optional' row. When a row in the vdsl2LineConfProfTable table (the parent row) is created, the SNMP agent will automatically create a 'mandatory' row in this table. When the parent row is deleted, the SNMP agent will automatically delete all associated rows in this table. Any attempt to delete the 'mandatory' row using the vdsl2LConfProfModeSpecRowStatus attribute will be rejected by the SNMP agent. The manager MAY create an 'optional' row in this table using the vdsl2LConfProfModeSpecRowStatus attribute if the parent row exists. The manager MAY delete an 'optional' row in this table using the vdsl2LConfProfModeSpecRowStatus attribute at any time. If the actual transmission mode of a DSL line does not match one of the 'optional' rows in this table, then the line will use the PSD configuration from the 'mandatory' row. The indexes of this entry are vdsl2SpectrumProfName and vdsl2SpectrumProfXdslMode. | |
| VDS vdsl2SpectrumProfXdslMode | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.1 | Vdsl2OperationModes | not-accessible | The xDSL Mode is a way of categorizing the various xDSL transmission modes into groups, each group (xDSL Mode) shares the same PSD configuration. There should be multiple entries in this table for a given line profile in case multiple bits are set in vdsl2LConfProfXtuTransSysEna for that profile. |
| I32 vdsl2SpectrumProfMaxNomPsdDs | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.2 | Integer32 | read-create | The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz). Unit: 0.1 dBm/Hz |
| I32 vdsl2SpectrumProfMaxNomPsdUs | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.3 | Integer32 | read-create | The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz. (physical values are -60 to -30 dBm/Hz). Unit: 0.1 dBm/Hz |
| U32 vdsl2SpectrumProfMaxNomAtpDs | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.4 | Unsigned32 | read-create | The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Unit: 0.1 dBm |
| U32 vdsl2SpectrumProfMaxNomAtpUs | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.5 | Unsigned32 | read-create | The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Unit: 0.1 dBm |
| I32 vdsl2SpectrumProfMaxAggRxPwrUs | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.6 | Integer32 | read-create | The maximum upstream aggregate receive power over the relevant set of sub-carriers. The xTU-C should verify that the upstream power cutback is such that this maximum aggregate receive power value is honored. It ranges from -255 to 255 units of 0.1 dBm (physical values are -25.5 to 25.5 dBm). A value of all means that there is no limit. Unit: 0.1 dBm |
| VDS vdsl2SpectrumProfPsdMaskDs | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.7 | Vdsl2PsdMaskDs | read-create | This configuration parameter defines the downstream PSD mask applicable at the U-C2 reference point. This MIB PSD mask may impose PSD restrictions in addition to the Limit PSD mask defined in the relevant Recommendation (e.g., G.992.5, G.993.2). This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0xff. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup. |
| VDS vdsl2SpectrumProfPsdMaskUs | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.8 | Vdsl2PsdMaskUs | read-create | This configuration parameter defines the upstream PSD mask applicable at the U R2 reference point. This MIB PSD mask may impose PSD restrictions in addition to the Limit PSD mask defined in the relevant Recommendations (e.g., ITU-T Recommendations G.992.3, G.993.2). This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 45-47 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCus - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup. |
| VDS vdsl2SpectrumProfUpsPsdMaskSelection | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.9 | Vdsl2UpsPsdMaskSelection | read-create | This configuration parameter defines which upstream PSD mask is enabled. This parameter is used only for Annexes J and M of ITU T Recs G.992.3 and G.992.5. As only one selection parameter is defined in the MIB, the same selection value applies to all relevant modes enabled in the XTSE line configuration parameter. It ranges from 1 to 9 and selects the mask with the following definition This object is defaulted adlu-32/eu-32. |
| VDS vdsl2SpectrumProfPmMode | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.10 | Vdsl2LConfProfPmMode | read-create | Power management state Enabling. Defines the power states the ATU-C or ATU-R may autonomously transition to on this line. Options: 1. allowTransitionsToIdle (0) 2. allowTransitionsToLowPower (1) A bit with a '1' value means that the ATU is allowed to transit into the respective state and a '0' value means that the ATU is not allowed to transit into the respective state. |
| U32 vdsl2SpectrumProfL0Time | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.11 | Unsigned32 | read-create | This minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds. Unit: seconds |
| U32 vdsl2SpectrumProfL2Time | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.12 | Unsigned32 | read-create | This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds. Unit: seconds |
| U32 vdsl2SpectrumProfL2Atpr | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.13 | Unsigned32 | read-create | The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. Unit: dB |
| U32 vdsl2SpectrumProfL2Atprt | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.14 | Unsigned32 | read-create | The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and Power Trims. Unit: dB |
| ROW vdsl2SpectrumProfModeSpecRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.4.3.1.15 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated lines. |
| vdsl2SpectrumProfSubProfTable | 1.3.6.1.4.1.2011.6.115.1.5.4.4 | not-accessible | The table vdsl2SpectrumProfSubProfTable extends the VDSL2 line configuration profile by profile parameters. The indexes of this table are vdsl2SpectrumProfName, vdsl2SpectrumProfXdslMode, and vdsl2SpectrumProfSubProfiles. | |
| vdsl2SpectrumProfSubProfEntry | 1.3.6.1.4.1.2011.6.115.1.5.4.4.1 | not-accessible | The table vdsl2SpectrumProfSubProfTable extends the VDSL2 line configuration profile by profile parameters. The indexes of this entry are vdsl2SpectrumProfName, vdsl2SpectrumProfXdslMode, and vdsl2SpectrumProfSubProfiles. | |
| VDS vdsl2SpectrumProfSubProfiles | 1.3.6.1.4.1.2011.6.115.1.5.4.4.1.1 | Vdsl2SubProfiles | not-accessible | This configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line. This object is defaulted Profile17a. |
| VDS vdsl2SpectrumProfSubProfilesWeight | 1.3.6.1.4.1.2011.6.115.1.5.4.4.1.2 | Vdsl2SubProfilesWeight | read-create | This configuration parameter contains the G.993.2 profiles' weight to be allowed by the near-end xTU on this line. This object is defaulted priorityWeight1. |
| VDS vdsl2SpectrumProfPsdClassMask | 1.3.6.1.4.1.2011.6.115.1.5.4.4.1.3 | Vdsl2TIPsdClassMask | read-create | (CLASSMASK). In order to reduce the number of configuration possibilities, the limit Power Spectral Density masks (see LIMITMASK) are grouped in PSD mask classes. Each class is designed such that the PSD levels of each limit PSD mask of a specific class are equal in their respective passband above 276 kHz. This parameter is defined per VDSL2 Annex enabled in the xdsl2LConfProfXtuTransSysEna object. It selects a single PSD mask class per Annex that is activated at the VTU-O. This object is defaulted A998/B997M1c/C998. |
| VDS vdsl2SpectrumProfPsdLimitMask | 1.3.6.1.4.1.2011.6.115.1.5.4.4.1.4 | Vdsl2PsdLimitMask | read-create | (LIMITMASK). This configuration parameter contains the G.993.2 limit PSD masks of the selected PSD mask class, enabled by the near-end xTU on this line for each class of profiles. This parameter is defined per VDSL2 Annex enabled in the xdsl2LConfProfXtuTransSysEna object. Through this parameter several limit PSD masks of the selected PSD mask class (xdsl2LConfProfClassMask) may be enabled. The enabling parameter is coded in a bitmap representation (0 if the associated mask is not allowed, 1 if it is allowed).This object is defaulted AnnexB998-M2x-B. |
| VDS vdsl2SpectrumProfUs0PsdMask | 1.3.6.1.4.1.2011.6.115.1.5.4.4.1.5 | Vdsl2Us0PsdMask | read-create | This parameter contains the US0 PSD masks to be allowed by the near-end xTU on the line. This parameter is only defined for G.993.2 Annex A. It is represented as a bitmap (0 if not allowed and 1 if allowed) with the following definitions. This object is defaulted ADLU-32/EU-32. |
| VDS vdsl2SpectrumProfUs0Disable | 1.3.6.1.4.1.2011.6.115.1.5.4.4.1.6 | Vdsl2Us0Disable | read-create | This configuration parameter indicates if the use of US0 is disabled for each limit PSD mask enabled in the LIMITMASK parameter. This object is defaulted Unused. |
| ROW vdsl2SpectrumProfSubProfRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.4.4.1.7 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated lines. |
| vdsl2DpboProfTable | 1.3.6.1.4.1.2011.6.115.1.5.4.5 | not-accessible | The table vdsl2DpboProfTable contains VDSL2 DPBO configuration. The index of this table is vdsl2DpboProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| vdsl2DpboProfEntry | 1.3.6.1.4.1.2011.6.115.1.5.4.5.1 | not-accessible | The table vdsl2DpboProfTable contains VDSL2 DPBO configuration. The index of this entry is vdsl2DpboProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| OCT vdsl2DpboProfName | 1.3.6.1.4.1.2011.6.115.1.5.4.5.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| U32 vdsl2DpboProfWkMdMask | 1.3.6.1.4.1.2011.6.115.1.5.4.5.1.2 | Unsigned32 | read-create | This configuration parameter defines the current enabled DPBO working mode mask. DPBO working mode enabling:1-ADSL, 2-ADSL2+ 3-VDSL2. Options: 1. current enabled dpbo work mode:ADSL 2. current enabled dpbo work mode:ADSL2+ 3. current enabled dpbo work mode:ADSL,ADSL2+ 4. current enabled dpbo work mode:VDSL2 5. current enabled dpbo work mode:ADSL,VDSL2 6. current enabled dpbo work mode:ADSL2+,VDSL2 7. current enabled dpbo work mode:ADSL,ADSL2+,VDSL2 |
| VDS vdsl2DpboProfEpsd | 1.3.6.1.4.1.2011.6.115.1.5.4.5.1.3 | Vdsl2DpboEpsd | read-create | This parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as PSDMASKds.The maximum number of breakpoints for DPBOEPSD is 16. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff. |
| U32 vdsl2DpboProfEsel | 1.3.6.1.4.1.2011.6.115.1.5.4.5.1.4 | Unsigned32 | read-create | This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid.If DPBOESEL is set to zero, the DPBO in this section shall be disabled. Unit: 0.5dB |
| VDS vdsl2DpboProfEscm | 1.3.6.1.4.1.2011.6.115.1.5.4.5.1.5 | Vdsl2DpboEscm | read-create | This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid. Octets 0+1 DPBOESCMA Octets 2+3 DPBOESCMB Octets 4+5 DPBOESCMC |
| U32 vdsl2DpboProfMus | 1.3.6.1.4.1.2011.6.115.1.5.4.5.1.6 | Unsigned32 | read-create | DPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX defined below. It shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid. Unit: -0.5dBm/Hz |
| U32 vdsl2DpboProfFmin | 1.3.6.1.4.1.2011.6.115.1.5.4.5.1.7 | Unsigned32 | read-create | DPBOFMIN defines the minimum frequency from which the DPBO shall be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0) to 8832 kHz (coded as 2048). Unit: 4.3125 KHz |
| U32 vdsl2DpboProfFmax | 1.3.6.1.4.1.2011.6.115.1.5.4.5.1.8 | Unsigned32 | read-create | DPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956). Unit: 4.3125 KHz |
| ROW vdsl2DpboProfRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.4.5.1.9 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated lines. |
| U32 vdsl2DpboProfEselMin | 1.3.6.1.4.1.2011.6.115.1.5.4.5.1.65535 | Unsigned32 | read-create | DPBOESELMIN in dB is the minimum of all main cable losses for the KVz supplied when using the SOL model (expansion of a KVz and VDSL2 provision of additional KVz areas from this KVz using cross-cables to additional KVz), including the KVz at the MSAN site. This value must be adjustable as the minimum requirement via the SNMP interface in the configuration profile for each VDSL2 port, and is set individually for each MSAN site and usage. As an option, As an option, adjustment can be done for each MSAN or line card, thus taking effect for entire port groups. It is used only for determining the MUF. Unit: 0.5dB |
| vdsl2UpboProfTable | 1.3.6.1.4.1.2011.6.115.1.5.4.6 | not-accessible | The table vdsl2UpboProfTable contains VDSL2 upbo configuration. The index of this table is vdsl2UpboProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| vdsl2UpboProfEntry | 1.3.6.1.4.1.2011.6.115.1.5.4.6.1 | not-accessible | The table vdsl2UpboProfTable contains VDSL2 upbo configuration . The index of this entry is vdsl2UpboProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| OCT vdsl2UpboProfName | 1.3.6.1.4.1.2011.6.115.1.5.4.6.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| VDS vdsl2UpboProfPsdBand | 1.3.6.1.4.1.2011.6.115.1.5.4.6.1.2 | Vdsl2UpboPsdBand | read-create | This parameter defines the UPBO reference PSD used to compute the upstream power back-off for each upstream band. A UPBOPSD defined for each band shall consist of two parameters [a, b]. Parameter a shall be coded as an unsigned 12-bit number from 40 dBm/Hz (coded as 0) to 80.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz; and b shall be coded as an unsigned 12 bit number from 0 (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency f expressed in MHz shall be equal to '-a-b(SQRT(f))'. The set of parameter values a = 40 dBm/Hz, b = 0 dBm/Hz is a special configuration to disable UPBO in the respective upstream band. Octets 0+1 - a[0] Octets 2+3 - b[0] Octets 4+5 - a[1] Octets 6+7 - b[1] Octets 8+9 - a[2] Octets 10+11 - b[2] Octets 12+13 - a[3] Octets 14+15 - b[3] Octets 16+17 - a[4] Octets 18+19 - b[4] |
| U32 vdsl2UpboProfKl | 1.3.6.1.4.1.2011.6.115.1.5.4.6.1.3 | Unsigned32 | read-create | This parameter defines the electrical loop length expressed in dB at 1MHz, kl0, configured by the CO-MIB. The value shall be coded as an unsigned 16 bit number in the range 0 (coded as 0) to 128 dB (coded as 1280) in steps of 0.1 dB. Unit: 0.1 dB |
| VDS vdsl2UpboProfKlf | 1.3.6.1.4.1.2011.6.115.1.5.4.6.1.4 | Vdsl2UpboKlf | read-create | This parameter is a flag that forces the VTU-R to use the electrical loop length of the CO-MIB (UPBOKL) to compute the UPBO. The value shall be forced if the flag is set to 1. Otherwise, the electrical loop length shall be autonomously selected by the VTU-O. |
| U32 vdsl2UpboProfKlAuto | 1.3.6.1.4.1.2011.6.115.1.5.4.6.1.5 | Unsigned32 | read-create | This parameter defines the mode in which kl0 is computed when Vdsl2UpboKlf is auto. The value is defined as below: 1-max(kl0CO,kl0CPE) 2-min(kl0CO,kl0CPE) 3-kl0CO 4-kl0CPE The default value is 3 |
| ROW vdsl2UpboProfRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.4.6.1.6 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated lines. |
| VDS vdsl2UpboProfBoostMode | 1.3.6.1.4.1.2011.6.115.1.5.4.6.1.65535 | Vdsl2UpboBoostMode | read-create | This object indicates whether the equalized FEXT UPBO method is supported or not. Options: 1. disable(1) - The Equalized FEXT UPBO method is not supported 2. enable(2) - The Equalized FEXT UPBO method is supported |
| VDS vdsl2UpboProfKl0RefBand | 1.3.6.1.4.1.2011.6.115.1.5.4.6.1.65536 | Vdsl2UpboKl0RefBand | read-create | Octets 0+1 - length[1] Octets 2+3 - length[2] Octets 4+5 - length[3] Octets 6+7 - length[4] |
| vdsl2NoiseMarginProfTable | 1.3.6.1.4.1.2011.6.115.1.5.4.7 | not-accessible | The table vdsl2NoiseMarginProfTable contains VDSL2 noise margin configuration. The index of this table is vdsl2NoiseMarginProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| vdsl2NoiseMarginProfEntry | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1 | not-accessible | The table vdsl2NoiseMarginProfTable contains VDSL2 noise margin configuration. The index of this entry is vdsl2NoiseMarginProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| OCT vdsl2NoiseMarginProfName | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| U32 vdsl2NoiseMarginProfTargetSnrmDs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.2 | Unsigned32 | read-create | The minimum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2NoiseMarginProfTargetSnrmUs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.3 | Unsigned32 | read-create | The minimum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the upstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2NoiseMarginProfMaxSnrmDs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.4 | Unsigned32 | read-create | The maximum Noise Margin the xTU-R receiver shall try to sustain. If the Noise Margin is above this level, the xTU-R shall request that the xTU-C reduce the xTU-C transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of all 1's means that there is no maximum. Unit: 0.1 dB |
| U32 vdsl2NoiseMarginProfMaxSnrmUs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.5 | Unsigned32 | read-create | The maximum Noise Margin the xTU-C receiver shall try to sustain. If the Noise Margin is above this level, the xTU-C shall request that the xTU-R reduce the xTU-R transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of all 1's means that there is no maximum. Unit: 0.1 dB |
| U32 vdsl2NoiseMarginProfMinSnrmDs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.6 | Unsigned32 | read-create | The minimum Noise Margin the xTU-R receiver shall tolerate. If the noise margin falls below this level, the xTU-R shall request that the xTU-C increase the xTU-C transmit power. If an increase to xTU-C transmit power is not possible, a loss-of-margin (LOM) defect occurs, the xTU-R shall fail and attempt to reinitialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0 means that there is no minimum. Unit: 0.1 dB |
| U32 vdsl2NoiseMarginProfMinSnrmUs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.7 | Unsigned32 | read-create | The minimum Noise Margin the xTU-C receiver shall tolerate. If the noise margin falls below this level, the xTU-C shall request that the xTU-R increase the xTU-R transmit power. If an increase of xTU-R transmit power is not possible, a loss-of-margin (LOM) defect occurs, the xTU-C shall fail and attempt to re-initialize and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). A value of 0 means that there is no minimum. Unit: 0.1 dB |
| U32 vdsl2NoiseMarginProfRaUsNrmDs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.8 | Unsigned32 | read-create | The Downstream Up-Shift Noise Margin value, to be used when Vdsl2LineConfRaModeDs is set to DynamicRa. If the downstream noise margin is above this value and stays above it for more than the time specified by the Vdsl2ServProfRaUsTimeDs, the xTU-R shall attempt to increase the downstream net data rate. The Downstream Up-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2NoiseMarginProfRaUsNrmUs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.9 | Unsigned32 | read-create | The Upstream Up-Shift Noise Margin value, to be used when Vdsl2LineConfRaModeUs is set to DynamicRa. If the upstream noise margin is above this value and stays above it for more than the time specified by the Vdsl2LineConfRaUsTimeUs, the xTU-C shall attempt to increase the upstream net data rate. The Upstream Up-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2NoiseMarginProfRaUsTimeDs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.10 | Unsigned32 | read-create | The Downstream Up-Shift Time Interval, to be used when Vdsl2LineConfRaModeDs is set to DynamicRa. The interval of time that the downstream noise margin should stay above the Downstream Up-shift Noise Margin before the xTU-R shall attempt to increase the downstream net data rate. Unit: seconds |
| U32 vdsl2NoiseMarginProfRaUsTimeUs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.11 | Unsigned32 | read-create | The Upstream Up-Shift Time Interval, to be used when Vdsl2LineConfRaModeUs is set to DynamicRa. The interval of time the upstream noise margin should stay above the Upstream Up-shift Noise Margin before the xTU-C shall attempt to increase the upstream net data rate. Unit: seconds |
| U32 vdsl2NoiseMarginProfRaDsNrmsDs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.12 | Unsigned32 | read-create | The Downstream Down-Shift Noise Margin value, to be used when Vdsl2LineConfRaModeDs is set to DynamicRa. If the downstream noise margin is below this value and stays below that for more than the time specified by the Vdsl2LineConfRaDsTimeDs, the xTU-R shall attempt to decrease the downstream net data rate. The Downstream Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2NoiseMarginProfRaDsNrmsUs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.13 | Unsigned32 | read-create | The Upstream Downshift Noise Margin value, to be used when Vdsl2LineConfRaModeUs is set to DynamicRa. If the upstream noise margin is below this value and stays below that for more than the time specified by the Vdsl2LineConfRaDsTimeUs, the xTU-C shall attempt to decrease the upstream net data rate. The Upstream Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Unit: 0.1 dB |
| U32 vdsl2NoiseMarginProfRaDsTimeDs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.14 | Unsigned32 | read-create | The Downstream Downshift Time Interval, to be used when Vdsl2LineConfRaModeDs is set to DynamicRa. The interval of time the downstream noise margin should stay below the Downstream Down-shift Noise Margin before the xTU-R shall attempt to decrease the downstream net data rate. Unit: seconds |
| U32 vdsl2NoiseMarginProfRaDsTimeUs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.15 | Unsigned32 | read-create | The Upstream Down-Shift Time Interval, to be used when Vdsl2LineConfRaModeUs is set to DynamicRa. The interval of time the upstream noise margin should stay below the Upstream Down-shift Noise Margin before the xTU-C shall attempt to decrease the upstream net data rate. Unit: seconds |
| U32 vdsl2NoiseMarginProfDsThresholdDs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.16 | Unsigned32 | read-create | Data Rate Threshold Downshift for downstream direction. A 'Down-shift rate change' event is triggered when the actual downstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bit/s. Unit: bits/second |
| U32 vdsl2NoiseMarginProfUsThresholdDs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.17 | Unsigned32 | read-create | Data Rate Threshold Up shift for downstream direction. An 'Up-shift rate change' event is triggered when the actual downstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bit/s. Unit: bits/second |
| U32 vdsl2NoiseMarginProfDsThresholdUs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.18 | Unsigned32 | read-create | Data Rate Threshold Downshift for upstream direction. A 'Down-shift rate change' event is triggered when the actual upstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bit/s. Unit: bits/second |
| U32 vdsl2NoiseMarginProfUsThresholdUs | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.19 | Unsigned32 | read-create | Data Rate Threshold Up shift for upstream direction. An 'Up-shift rate change' event is triggered when the actual upstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bit/s. Unit: bits/second |
| ROW vdsl2NoiseMarginProfRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.4.7.1.20 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated lines. |
| vdsl2DelayInpProfTable | 1.3.6.1.4.1.2011.6.115.1.5.4.8 | not-accessible | The table vdsl2DelayInpProfTable contains VDSL2 delay inp configuration. The index of this table is vdsl2DelayInpProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| vdsl2DelayInpProfEntry | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1 | not-accessible | The table vdsl2DelayInpProfTable contains VDSL2 delay inp configuration. The index of this entry is vdsl2DelayInpProfName. A default profile with an index of 'DEFVAL' will always exist and its parameters will be set to vendor-specific values, unless otherwise specified in this document. | |
| OCT vdsl2DelayInpProfName | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.1 | OCTET STRING | not-accessible | This object identifies a row in this table. |
| VDS vdsl2DelayInpProfForceINP | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.2 | Vdsl2ForceINP | read-create | This parameter indicates that the framer settings of the bearer shall be selected such that the impulse noise protection computed according to the formula specified in the relevant Recommendation is greater or equal to the minimal impulse noise protection requirement. This flag shall have the same value for all the bearers of one line in the same direction. |
| U32 vdsl2DelayInpProfCh1MaxDelayDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.3 | Unsigned32 | read-create | If retransmission is not used in downstream direction,this parameter is maximum interleave delay on downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Vdsl2ChanStatusActDelay) is as close as possible to, but less than or equal to, Vdsl2ChanConfMaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Unit: milliseconds |
| U32 vdsl2DelayInpProfCh1MaxDelayUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.4 | Unsigned32 | read-create | If retransmission is not used in upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Vdsl2ChanStatusActDelay) is as close as possible to, but less than or equal to, Vdsl2ChanConfMaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Unit: milliseconds |
| VDS vdsl2DelayInpProfCh1MinProtectionDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.5 | Vdsl2SymbolProtectionDs | read-create | If retransmission is not used in downstream direction,this parameter is minimum impulse noise protection for the bearer channel on downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Unit: symbols |
| VDS vdsl2DelayInpProfCh1MinProtectionUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.6 | Vdsl2SymbolProtectionUs | read-create | If retransmission is not used in upstream direction,this parameter is minimum impulse noise protection for the bearer channel on upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Unit: symbols |
| U32 vdsl2DelayInpProfCh2MaxDelayDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.7 | Unsigned32 | read-create | Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Vdsl2ChanStatusActDelay) is as close as possible to, but less than or equal to, Vdsl2ChanConfMaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Unit: milliseconds |
| U32 vdsl2DelayInpProfCh2MaxDelayUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.8 | Unsigned32 | read-create | Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (Vdsl2ChanStatusActDelay) is as close as possible to, but less than or equal to, Vdsl2ChanConfMaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Unit: milliseconds |
| VDS vdsl2DelayInpProfCh2MinProtectionDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.9 | Vdsl2SymbolProtectionDs | read-create | Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Unit: symbols |
| VDS vdsl2DelayInpProfCh2MinProtectionUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.10 | Vdsl2SymbolProtectionUs | read-create | Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Unit: symbols |
| ROW vdsl2DelayInpProfRowStatus | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.11 | RowStatus | read-create | This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be not referenced from all associated lines. |
| VDS vdsl2DelayInpProfCh1PhyRcontrolDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.12 | Vdsl2PhyRControl | read-write | To enable or disable the retransmission function on downstream direction. |
| VDS vdsl2DelayInpProfCh1PhyRcontrolUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.13 | Vdsl2PhyRControl | read-write | To enable or disable the retransmission function on upstream direction. |
| VDS vdsl2DelayInpProfCh1INPmaxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.14 | Vdsl2SymbolProtectionDs | read-write | Maximum Impulse Noise Protection on downstream direction. Options: 1. noProtection(1) 2. halfSymbol(2) 3. singleSymbol(3) 4. twoSymbols(4) 5. threeSymbols(5) 6. fourSymbols(6) 7. fiveSymbols(7) 8. sixSymbols(8) 9. sevenSymbols(9) 10. eightSymbols(10) 11. nineSymbols(11) 12. tenSymbols(12) 13. elevenSymbols(13) 14. twelveSymbols(14) 15. thirteeSymbols(15) 16. fourteenSymbols(16) 17. fifteenSymbols(17) 18. sixteenSymbols(18) The value multiply 1/2 is the real value of Noise Protection values. Unit: DMT Symbol |
| VDS vdsl2DelayInpProfCh1INPmaxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.15 | Vdsl2SymbolProtectionUs | read-write | Maximum Impulse Noise Protection on upstream direction. Options: 1. noProtection(1) 2. halfSymbol(2) 3. singleSymbol(3) 4. twoSymbols(4) 5. threeSymbols(5) 6. fourSymbols(6) 7. fiveSymbols(7) 8. sixSymbols(8) 9. sevenSymbols(9) 10. eightSymbols(10) 11. nineSymbols(11) 12. tenSymbols(12) 13. elevenSymbols(13) 14. twelveSymbols(14) 15. thirteeSymbols(15) 16. fourteenSymbols(16) 17. fifteenSymbols(17) 18. sixteenSymbols(18) The value multiply 1/2 is the real value of Noise Protection values. Unit: DMT Symbol |
| I32 vdsl2DelayInpProfCh1MinRtxRatioDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.16 | Integer32 | read-write | Minimum rtxratio on downstream direction. Unit: 1/256 |
| I32 vdsl2DelayInpProfCh1MinRtxRatioUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.17 | Integer32 | read-write | Minimum rtxratio on upstream direction. Unit: 1/256 |
| I32 vdsl2DelayInpProfCh1MinRSoverheadDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.18 | Integer32 | read-write | The minimum value of R/N on downstream direction. Unit: 1/256 |
| I32 vdsl2DelayInpProfCh1MinRSoverheadUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.19 | Integer32 | read-write | The minimum value of R/N on upstream direction. Unit: 1/256 |
| VDS vdsl2DelayInpProfCh2PhyRcontrolDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.20 | Vdsl2PhyRControl | read-write | To enable or disable the retransmission function on downstream direction. |
| VDS vdsl2DelayInpProfCh2PhyRcontrolUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.21 | Vdsl2PhyRControl | read-write | To enable or disable the retransmission function on upstream direction. |
| VDS vdsl2DelayInpProfCh2INPmaxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.22 | Vdsl2SymbolProtectionDs | read-write | Maximum Impulse Noise Protection on downstream direction. Options: 1. noProtection(1) 2. halfSymbol(2) 3. singleSymbol(3) 4. twoSymbols(4) 5. threeSymbols(5) 6. fourSymbols(6) 7. fiveSymbols(7) 8. sixSymbols(8) 9. sevenSymbols(9) 10. eightSymbols(10) 11. nineSymbols(11) 12. tenSymbols(12) 13. elevenSymbols(13) 14. twelveSymbols(14) 15. thirteeSymbols(15) 16. fourteenSymbols(16) 17. fifteenSymbols(17) 18. sixteenSymbols(18) The value multiply 1/2 is the real value of Noise Protection values. Unit: DMT Symbol |
| VDS vdsl2DelayInpProfCh2INPmaxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.23 | Vdsl2SymbolProtectionUs | read-write | Maximum Impulse Noise Protection on upstream direction. Options: 1. noProtection(1) 2. halfSymbol(2) 3. singleSymbol(3) 4. twoSymbols(4) 5. threeSymbols(5) 6. fourSymbols(6) 7. fiveSymbols(7) 8. sixSymbols(8) 9. sevenSymbols(9) 10. eightSymbols(10) 11. nineSymbols(11) 12. tenSymbols(12) 13. elevenSymbols(13) 14. twelveSymbols(14) 15. thirteeSymbols(15) 16. fourteenSymbols(16) 17. fifteenSymbols(17) 18. sixteenSymbols(18) The value multiply 1/2 is the real value of Noise Protection values. Unit: DMT Symbol |
| I32 vdsl2DelayInpProfCh2MinRtxRatioDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.24 | Integer32 | read-write | Minimum rtxratio on downstream direction. Unit: 1/256 |
| I32 vdsl2DelayInpProfCh2MinRtxRatioUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.25 | Integer32 | read-write | Minimum rtxratio on upstream direction. Unit: 1/256 |
| I32 vdsl2DelayInpProfCh2MinRSoverheadDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.26 | Integer32 | read-write | The minimum value of R/N on downstream direction. Unit: 1/256 |
| I32 vdsl2DelayInpProfCh2MinRSoverheadUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.27 | Integer32 | read-write | The minimum value of R/N on upstream direction. Unit: 1/256 |
| U32 hwvdsl2DelayInpProfCh1MaxDelayRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.28 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the maximum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 1 to 63 ms by steps of 1 ms. Unit: milliseconds |
| U32 hwvdsl2DelayInpProfCh1MaxDelayRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.29 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the maximum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 1 to 63 ms by steps of 1 ms. Unit: milliseconds |
| U32 hwvdsl2DelayInpProfCh1MinDelayRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.30 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 0 to 63 ms by steps of 1 ms. Unit: milliseconds |
| U32 hwvdsl2DelayInpProfCh1MinDelayRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.31 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum for the instantaneous delay due to the effect of retransmission only (see G.998.4 for detailed specification). The delay ranges from 0 to 63 ms by steps of 1 ms. Unit: milliseconds |
| U32 hwvdsl2DelayInpProfCh1MinInpShineRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.32 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 63, inclusive. Unit: symbols |
| U32 hwvdsl2DelayInpProfCh1MinInpShineRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.33 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 63, inclusive. Unit: symbols |
| U32 hwvdsl2DelayInpProfCh1MinInp8ShineRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.34 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 127, inclusive. Unit: symbols |
| U32 hwvdsl2DelayInpProfCh1MinInp8ShineRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.35 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against SHINE for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 127, inclusive. Unit: symbols |
| U32 hwvdsl2DelayInpProfCh1ShineRatioRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.36 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the SHINE ratio (detailed definition see G.998.4). The values range from 0 to 0.100 in increments of 0.001. |
| U32 hwvdsl2DelayInpProfCh1ShineRatioRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.37 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the SHINE ratio (detailed definition see G.998.4). The values range from 0 to 0.100 in increments of 0.001. |
| U32 hwvdsl2DelayInpProfCh1MinInpReinRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.38 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 7, inclusive. |
| U32 hwvdsl2DelayInpProfCh1MinInpReinRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.39 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 4.3125 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 4.3125 kHz and can take any integer value from 0 to 7, inclusive. |
| U32 hwvdsl2DelayInpProfCh1MinInp8ReinRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.40 | Unsigned32 | read-create | If retransmission is used in downstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 13, inclusive. |
| U32 hwvdsl2DelayInpProfCh1MinInp8ReinRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.41 | Unsigned32 | read-create | If retransmission is used in upstream direction, this parameter specifies the minimum impulse noise protection against REIN for the bearer channel if it is transported over DMT symbols with a subcarrier spacing of 8.625 kHz. The impulse noise protection is expressed in DMT symbols with a subcarrier spacing of 8.625 kHz and can take any integer value from 0 to 13, inclusive. |
| INT hwvdsl2DelayInpProfCh1IatReinRtxDs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.42 | INTEGER | read-create | If retransmission is used in downstream direction, this parameter specifies the inter-arrival time that shall be assumed for REIN protection. Options: 1. frequency100Hz(0) - an inter-arrival time derived from a REIN at 100 Hz 2. frequency120Hz(1) - an inter-arrival time derived from a REIN at 120 Hz |
| INT hwvdsl2DelayInpProfCh1IatReinRtxUs | 1.3.6.1.4.1.2011.6.115.1.5.4.8.1.43 | INTEGER | read-create | If retransmission is used in upstream direction, this parameter specifies the inter-arrival time that shall be assumed for REIN protection. Options: 1. frequency100Hz(0) - an inter-arrival time derived from a REIN at 100 Hz 2. frequency120Hz(1) - an inter-arrival time derived from a REIN at 120 Hz |
| vdsl2Scalar | 1.3.6.1.4.1.2011.6.115.1.6 | |||
| vdsl2ScalarSC | 1.3.6.1.4.1.2011.6.115.1.6.1 | |||
| U32 vdsl2ScalarSCMaxInterfaces | 1.3.6.1.4.1.2011.6.115.1.6.1.1 | Unsigned32 | read-only | This value determines the maximum number of interfaces supported by vdsl2SCStatusTable, vdsl2SCStatusBandTable, and vdsl2SCStatusSegmentTable. |
| U32 vdsl2ScalarSCAvailInterfaces | 1.3.6.1.4.1.2011.6.115.1.6.1.2 | Unsigned32 | read-only | This value determines the currently available number of interfaces listed in vdsl2SCStatusTable, vdsl2SCStatusBandTable, and vdsl2SCStatusSegmentTable. |
| vdsl2Conformance | 1.3.6.1.4.1.2011.6.115.1.8 | |||
| vdsl2Groups | 1.3.6.1.4.1.2011.6.115.1.8.1 | |||
| vdsl2LineGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.1 | The group of configuration, status, and commands objects on the line level. | ||
| vdsl2ChannelStatusGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.2 | The group of status objects on the channel level. | ||
| vdsl2ChannelStatusAtmGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.3 | The group of status objects on the data path level when it is ATM. | ||
| vdsl2ChannelStatusPtmGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.4 | The group of status objects on the data path level when it is PTM. | ||
| vdsl2PrivSCStatusGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.5 | The group of status objects on the sub-carrier level. They are updated as a result of a DELT process. | ||
| vdsl2DeltGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.6 | The group of status objects on the sub-carrier level. They are updated as a result of a DELT process. | ||
| vdsl2LineInventoryGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.7 | The group of inventory objects per xTU. | ||
| vdsl2LineConfTemplateGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.8 | The group of objects in a line configuration template. | ||
| vdsl2LineConfProfGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.9 | The group of objects in a line configuration profile. | ||
| vdsl2LineConfProfRaGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.10 | The group of objects required for controlling the rate adaptive behavior of the line. | ||
| vdsl2LineConfProfMsgMinGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.11 | The group of objects required for controlling the rate reserved for Overhead traffic. | ||
| vdsl2LineConfProfModeSpecGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.12 | The group of objects in a line configuration profile that have an instance for each operation mode allowed. | ||
| vdsl2ChConfProfileGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.13 | The group of objects in a channel configuration profile. | ||
| vdsl2ChConfProfileAtmGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.14 | The group of configuration objects required when the data path is ATM. | ||
| vdsl2ChConfProfileMinResGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.15 | The group of configuration objects required for the reserved data rate. | ||
| vdsl2LineAlarmConfTemplateGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.16 | The group of objects in a line alarm template. | ||
| vdsl2LineAlarmConfProfileGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.17 | The group of objects in a line alarm profile. | ||
| vdsl2ChAlarmConfProfileGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.18 | The group of objects in a channel alarm profile. | ||
| vdsl2PMLineCurrGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.19 | The group of objects that report the line level counters for current PM intervals. | ||
| vdsl2PMLineCurrInitGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.20 | The group of objects that report the full initializations counters for current PM intervals. | ||
| vdsl2PMLineCurrInitShortGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.21 | The group of objects that report the short initializations counters for current PM intervals. | ||
| vdsl2PMLineHist15MinGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.22 | The group of line level PM counters for the previous 15 minutes intervals. | ||
| vdsl2PMLineHist1DayGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.23 | The group of line level PM counters for the previous 24 hours intervals. | ||
| vdsl2PMLineInitHist15MinGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.24 | The group of PM counters for the previous 15 minutes intervals full initializations. | ||
| vdsl2PMLineInitHist15MinShortGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.25 | The group of PM counters for the previous 15 minutes intervals short initializations. | ||
| vdsl2PMLineInitHist1DayGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.26 | The group of PM counters for the previous 24 hours intervals full initializations. | ||
| vdsl2PMLineInitHist1DayShortGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.27 | The group of PM counters for the previous 24 hours intervals short initializations. | ||
| vdsl2PMChCurrGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.28 | The group of objects that report the channel level counters for current PM intervals. | ||
| vdsl2PMChHist15MinGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.29 | The group of objects that report the channel level counters for previous 15 minutes PM intervals. | ||
| vdsl2PMChHist1DGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.30 | The group of objects that report the channel level counters for previous 24 hours PM intervals. | ||
| vdsl2ScalarDeltGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.31 | The group of objects that report the available memory resources for DELT processes. | ||
| vdsl2ThreshNotificationGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.32 | This notification indicates alarm when this group supports notifications of significant conditions associated with VDSL2 lines. | ||
| vdsl2StatusChangeNotificationGroup | 1.3.6.1.4.1.2011.6.115.1.8.1.33 | This notification indicates alarm when this group supports notifications of thresholds crossing associated with VDSL2 lines. | ||
| vdsl2Compliances | 1.3.6.1.4.1.2011.6.115.1.8.2 | |||
| vdsl2LineMibCompliance | 1.3.6.1.4.1.2011.6.115.1.8.2.1 | The compliance statement for SNMP entities which manage VDSL2 interfaces. | ||
| vdsl2Mode | 1.3.6.1.4.1.2011.6.115.1.9 | |||
| VDS hwvdslmodecfg | 1.3.6.1.4.1.2011.6.115.1.9.1 | Vdsl2CfgMode | read-write | This object is used to change VDSL management mode. After the mode being changed, system will automatically save data and reboot. |
| vdsl2GlobalConfig | 1.3.6.1.4.1.2011.6.115.1.10 | |||
| INT vdsl2DpboEselGlobalConfigSwitch | 1.3.6.1.4.1.2011.6.115.1.10.1 | INTEGER | read-write | Enable/Disable VDSL port DPBOESEL shall Feature. This object is defaulted disabled(2). Options: 1. enabled(1) - enabled the switch 2. disabled(2) - disabled the switch |
| U32 vdsl2DpboEselGlobalConfigValue | 1.3.6.1.4.1.2011.6.115.1.10.2 | Unsigned32 | read-write | This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid.If DPBOESEL is set to zero, the DPBO in this section shall be disabled. This object is defaulted 84. Unit: 0.5dB |
| INT vdsl2ProfileAutoNegotiationSwitch | 1.3.6.1.4.1.2011.6.115.1.10.3 | INTEGER | read-write | Enable/Disable the VDSL2 G993.2 profile auto-negotiation function. Default values:disabled(2). Options: 1. enabled(1) - enabled the switch 2. disabled(2) - disabled the switch |
| INT vdsl2MaximumInterleavedDepth | 1.3.6.1.4.1.2011.6.115.1.10.4 | INTEGER | read-write | Set the VDSL2 maximum interleaved depth function. Default values:maxInterleavedDepth511(2). Options: 1. maxInterleavedDepth64(1) - it means the interleaving depth up to 64 can be selected 2. maxInterleavedDepth511(2) - it means the interleaving depth up to 512 can be selected |
| hwvdsl2AutoDeleteProfUnused | 1.3.6.1.4.1.2011.6.115.1.11 | |||
| INT hwvdsl2AutoDeleteProfUnusedProfType | 1.3.6.1.4.1.2011.6.115.1.11.1 | INTEGER | read-write | The profile type of deleting unused VDSL profile. Options: 1. vdsl2LineConfTemplate(1) - VDSL2 line template 2. vdsl2LineConfProf(2) - VDSL2 line profile 3. vdsl2ChConfProfile(3) - VDSL2 channel profile 4. vdsl2LineAlarmConfTemplate(4) - VDSL2 alarm template 5. vdsl2LineAlarmConfProfile(5) - VDSL2 alarm profile 6. vdsl2ChAlarmConfProfile(6) - VDSL2 channel alarm profile 7. vdsl2ServProf(7) - VDSL2 service profile 8. vdsl2SpectrumProf(8) - VDSL2 spectrum profile 9. vdsl2DpboProf(9) - VDSL2 dpbo profile 10. vdsl2UpboProf(10) - VDSL2 upbo profile 11. vdsl2NoiseMarginProf(11) - VDSL2 noise-margin profile 12. vdsl2DelayInpProf(12) - VDSL2 inp-delay profile 13. vopDataRateConfProf(13) - XDSL data rate profile 14. vopLineSpectrumConfProf(14) - XDSL line spectrum profile 15. vopUPBOConfProf(15) - XDSL upbo profile 16. vopDPBOConfProf(16) - XDSL dpbo profile 17. vopRFIConfProf(17) - XDSL rfi profile 18. vopSNRMarginConfProf(18) - XDSL noise-margin profile 19. vopINPDelayConfProf(19) - XDSL inp-delay profile 20. vopVirtualNoiseConfProf(20) - XDSL virtual noise profile 21. vopModeSpecificPSDConfProf(21) - XDSL PSD profile |
| INT hwvdsl2AutoDeleteProfUnusedOperType | 1.3.6.1.4.1.2011.6.115.1.11.2 | INTEGER | read-write | The operation type of deleting unused VDSL profile. This object is defaulted all(2). Options: 1. first(1) - Delete first profile 2. all(2) - Delete all profile |
| hwvdsl2Traps | 1.3.6.1.4.1.2011.6.115.1.15 | |||
| hwvdsl2CommonTraps | 1.3.6.1.4.1.2011.6.115.1.15.1 | |||
| hwvdsl2CommonTrapsPrefix | 1.3.6.1.4.1.2011.6.115.1.15.1.0 | |||
| NTF hwvdsl2ModeSwitchTrap | 1.3.6.1.4.1.2011.6.115.1.15.1.0.1 | VDSL mode switch trap. This trap message is generated when the VDSL line mode fails to be switched. | ||
| NTF hwvdsl2CurrentModeTrap | 1.3.6.1.4.1.2011.6.115.1.15.1.0.2 | VDSL current mode trap. This trap message is generated when the current mode of the VDSL line is reported to the NMS periodically. | ||
| NTF hwvdsl2PortStatusChangeTrap | 1.3.6.1.4.1.2011.6.115.1.15.1.0.3 | VDSL port status change trap. This trap message is generated when the port status changes, for example from up to down or from down to up.The parameter information about the trap message describes the current status of the link and the location where the trap message is generated. | ||
| NTF hwvdsl2DeltOperResultTrap | 1.3.6.1.4.1.2011.6.115.1.15.1.0.4 | VDSL delt trap. This trap message is generated when the result of the DELT performed on the VDSL line is reported. | ||
| NTF hwvdsl2TemplateIDChangeTrap | 1.3.6.1.4.1.2011.6.115.1.15.1.0.5 | VDSL template change trap. This trap message is generated when the VDSL templete changed. | ||
| hwvdsl2AlarmTraps | 1.3.6.1.4.1.2011.6.115.1.15.2 | |||
| hwvdsl2AlarmTrapsPrefix | 1.3.6.1.4.1.2011.6.115.1.15.2.0 | |||
| NTF hwvdsl2AutoDeactivateLackLicensesAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.1 | This trap message is generated when some xDSL ports or all the xDSL ports are automatically deactivated due to lack of licenses. | ||
| NTF hwvdsl2PortAutoDeactiveLineFaultAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.2 | This trap message is generated when the VDSL port is automatically deactivated due to the line fault. | ||
| NTF hwvdsl2PortReactiveAfterRecoverAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.3 | This trap message is generated when the VDSL port is re-activated after the VDSL line recovers. | ||
| NTF hwvdsl2PerformanceStatiReachThresholdAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.4 | This trap message is generated when the line performance statistics of the VDSL port reach the threshold. | ||
| NTF hwvdsl2DownstreamRateLowerThresholdAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.5 | This trap message is generated when the xDSL channel downstream rate is lower than the threshold. | ||
| NTF hwvdsl2ActivePortFailConfigParaAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.6 | This trap message is generated when it fails to activate the port by using the VDSL line configuration parameters. | ||
| NTF hwvdsl2PerformanceStatisReachThresholdAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.7 | This trap message is generated when the channel performance statistics of the VDSL port reach the threshold. | ||
| NTF hwvdsl2ChannelUpstreamLowerThresholdAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.8 | This trap message is generated when the xDSL channel upstream rate is lower than the threshold. | ||
| NTF hwvdsl2VTURPowerOffAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.9 | This trap message is generated when the VTU-R is powered off. | ||
| NTF hwvdsl2PortActiveRateChangeAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.10 | This trap message is generated when the VDSL port actived rate change. | ||
| NTF hwvdsl2ChipsetUnavailableAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.11 | This trap message is generated when the VDSL chipset is unavailable. | ||
| NTF hwvdsl2ChipsetRecoverAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.12 | This trap message is generated when the VDSL chipset recovers from unavailability. | ||
| NTF hwvdsl2ChannelUpstreamExcThreAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.13 | This trap message is generated when the xDSL channel upstream rate increases to a value higher than the threshold. | ||
| NTF hwvdsl2ChannelUpstreamRestoreThreAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.14 | This trap message is generated when the xDSL channel upstream rate decreases to a value lower than the threshold. | ||
| NTF hwvdsl2ChannelDownstreamExcThreAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.15 | This trap message is generated when the xDSL channel downstream rate increases to a value higher than the threshold. | ||
| NTF hwvdsl2ChannelDownstreamRestoreThreAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.16 | This trap message is generated when the xDSL channel downstream rate decreases to a value lower than the threshold. | ||
| NTF hwvdsl2UnSuppVectorPortActFailAlarmTrap | 1.3.6.1.4.1.2011.6.115.1.15.2.0.17 | When the CPE connected to the port does not support vectoring and cannot be activated in 993.2 mode, this trap is sent. | ||
| hwvdsl2TrapsVbOids | 1.3.6.1.4.1.2011.6.115.1.16 | |||
| OCT hwvdsl2LinePMThresholdItem | 1.3.6.1.4.1.2011.6.115.1.16.1 | OCTET STRING | accessible-for-notify | Indicate the threshold item. |
| I32 hwvdsl2LinePMThresholdValue | 1.3.6.1.4.1.2011.6.115.1.16.2 | Integer32 | accessible-for-notify | VDSL threshold value |
| OCT hwvdsl2PortActFailReason | 1.3.6.1.4.1.2011.6.115.1.16.3 | OCTET STRING | accessible-for-notify | Indicate the the reason of the active port fail. |
| OCT hwvdsl2ChPMThresholdItem | 1.3.6.1.4.1.2011.6.115.1.16.4 | OCTET STRING | accessible-for-notify | Indicate the threshold value of threshold item . |
| I32 hwvdsl2ChPMCurrentValue | 1.3.6.1.4.1.2011.6.115.1.16.5 | Integer32 | accessible-for-notify | Indicate the current value of threshold item. |
| I32 hwvdsl2ChPMThresholdValue | 1.3.6.1.4.1.2011.6.115.1.16.6 | Integer32 | accessible-for-notify | Indicate the threshold value of threshold item. |
| I32 hwvdsl2LineActRateUs | 1.3.6.1.4.1.2011.6.115.1.16.7 | Integer32 | accessible-for-notify | Indicate the line active data rate in the upstream direction. |
| I32 hwvdsl2LineActRateDs | 1.3.6.1.4.1.2011.6.115.1.16.8 | Integer32 | accessible-for-notify | Indicate the line active data rate in the downstream direction. |
| I32 hwvdsl2ChipsetID | 1.3.6.1.4.1.2011.6.115.1.16.9 | Integer32 | accessible-for-notify | ChipsetID, the chipset id of the board. |
| INT hwvdsl2ModeSwitchResult | 1.3.6.1.4.1.2011.6.115.1.16.10 | INTEGER | accessible-for-notify | VDSL mode switch result. Options: 1. success(0) - success 2. fail(1) - fail |
| I32 hwvdsl2LinePMCurrentValue | 1.3.6.1.4.1.2011.6.115.1.16.11 | Integer32 | accessible-for-notify | Indicate the current value of threshold item. |
| I32 hwVdsl2RequestID | 1.3.6.1.4.1.2011.6.115.1.16.12 | Integer32 | accessible-for-notify | Request ID |
| OCT hwACTChngeDesc | 1.3.6.1.4.1.2011.6.115.1.16.13 | OCTET STRING | accessible-for-notify | The VDSL port actived rate change description. |
| INT hwVdsl2TemplateType | 1.3.6.1.4.1.2011.6.115.1.16.14 | INTEGER | accessible-for-notify | Type of the VDSL template ID. Options: 1. lineConfTemplate(1) - VDSL2 line template 2. alarmConfTemplate(2) - VDSL2 alarm template 3. spectrumProf(3) - VDSL2 spectrum profile 4. dpboProf(4) - VDSL2 dpbo profile 5. upboProf(5) - VDSL2 upbo profile 6. serviceProf(6) - VDSL2 service profile 7. noiseMarginProf(7) - VDSL2 noise-margin profile 8. delayInpProf(8) - VDSL2 delay-inp profile |
RFC description
Manages VDSL2 line parameters including initialization, transmission modes, power management, and performance monitoring.
Start monitoring Huawei DSLAM/broadband access node/MSAN (VDSL2 line) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.