HUAWEI-OSPFV3-MIB

All MIBs › HUAWEI-OSPFV3-MIB

Organization: Huawei Technologies Co.,Ltd.

Last Updated: 2015-05-03

Category: Protocol: OSPF, Routing Protocols, Technology: IPv6, Vendor: Huawei

Description: Huawei OSPFv3 MIB for managing IPv6 OSPFv3 instances, areas, interfaces, and neighbor adjacencies.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-OSPFV3-MIB?

HUAWEI-OSPFV3-MIB is Huawei's implementation of the IETF OSPFv3 (OSPF for IPv6) draft standard MIB. Its objects cover router ID, admin status, version number, area/AS border-router status, AS-scope LSA count/checksum sum, originated/received new-LSA counts, external-LSA count and LSDB limit, graceful-restart support/interval/status/age/exit-reason, notification enable, reference bandwidth, and a per-area table (area ID, import-AS-external policy, SPF-run count, area/AS border-router counts). As a configuration/protocol-status MIB it lets an administrator confirm OSPFv3 is enabled with the correct router ID and area configuration, and watch SPF-run frequency as a sign of topology instability. It is deployed on Huawei routers running OSPFv3. Engineers can download the HUAWEI-OSPFV3-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-OSPFV3-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei routers (OSPFv3/IPv6 routing)

Monitoring Examples

An administrator checks hwOspfv3AreaSpfRuns for an area experiencing frequent recalculation, a sign of a flapping link or unstable neighbor destabilizing the OSPFv3 topology.

What Can Be Monitored

OSPFv3 area configuration and SPF recalculation frequency

Imported Objects

From HUAWEI-MIB

hwDatacomm

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex

From INET-ADDRESS-MIB

InetAddress
InetAddressPrefixLength
InetAddressType

From OSPF-MIB

BigMetric
DesignatedRouterPriority
HelloRange
Metric
Status

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32
mib-2

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwOspfv3	1.3.6.1.4.1.2011.5.25.147			The MIB module for OSPF version 3. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC draft-ietf-ospf-ospfv3-mib-11; see the RFC itself for full legal notices.
hwOspfv3Notifications	1.3.6.1.4.1.2011.5.25.147.0
NTF hwOspfv3VirtIfStateChange	1.3.6.1.4.1.2011.5.25.147.0.1			An ospfv3VirtIfStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual interface. This notification should be generated when the interface state regresses (e.g., goes from Point-to-Point to Down) or progresses to a terminal state (i.e., Point-to-Point).
NTF hwOspfv3NbrStateChange	1.3.6.1.4.1.2011.5.25.147.0.2			An ospfv3NbrStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., 2-Way or Full). When an neighbor transitions from or to Full on non-broadcast multi-access and broadcast networks, the notification should be generated by the designated router. A designated router transitioning to Down will be noted by ospfIfStateChange.
NTF hwOspfv3VirtNbrStateChange	1.3.6.1.4.1.2011.5.25.147.0.3			An ospfv3VirtNbrStateChange notification signifies that there has been a change in the state of an OSPFv3 virtual neighbor. This notification should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., Full).
NTF hwOspfv3IfConfigError	1.3.6.1.4.1.2011.5.25.147.0.4			An ospfv3IfConfigError notification signifies that a packet has been received on a non-virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming.
NTF hwOspfv3VirtIfConfigError	1.3.6.1.4.1.2011.5.25.147.0.5			An ospfv3VirtIfConfigError notification signifies that a packet has been received on a virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a notification only if it prevents an adjacency from forming.
NTF hwOspfv3IfRxBadPacket	1.3.6.1.4.1.2011.5.25.147.0.6			An ospfv3IfRxBadPacket notification signifies that an OSPFv3 packet that cannot be parsed has been received on a non-virtual interface.
NTF hwOspfv3VirtIfRxBadPacket	1.3.6.1.4.1.2011.5.25.147.0.7			An ospfv3VirtIfRxBadPacket notification signifies that an OSPFv3 packet that cannot be parsed has been received on a virtual interface.
NTF hwOspfv3IfStateChange	1.3.6.1.4.1.2011.5.25.147.0.8			An ospfv3IfStateChange notification signifies that there has been a change in the state of a non-virtual OSPFv3 interface. This notification should be generated when the interface state regresses (e.g., goes from Dr to Down) or progresses to a terminal state (i.e., Point-to-Point, DR Other, Dr, or Backup).
NTF hwOspfv3RestartStatusChange	1.3.6.1.4.1.2011.5.25.147.0.9			An ospfv3RestartStatusChange notification signifies that there has been a change in the graceful restart state for the router. This notification should be generated when the router restart status changes.
NTF hwOspfv3NbrRestartHelperStatusChange	1.3.6.1.4.1.2011.5.25.147.0.10			An ospfv3NbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the neighbor. This notification should be generated when the neighbor restart helper status transitions for a neighbor.
NTF hwOspfv3VirtNbrRestartHelperStatusChange	1.3.6.1.4.1.2011.5.25.147.0.11			An ospfv3VirtNbrRestartHelperStatusChange notification signifies that there has been a change in the graceful restart helper state for the virtual neighbor. This notification should be generated when the virtual neighbor restart helper status transitions for a virtual neighbor.
NTF hwOspfv3NssaTranslatorStatusChange	1.3.6.1.4.1.2011.5.25.147.0.12			An ospfv3NssaTranslatorStatusChange notification indicates that there has been a change in the router's ability to translate OSPFv3 NSSA LSAs into OSPFv3 External LSAs. This notification should be generated when the Translator Status transitions from or to any defined status on a per area basis.
NTF hwOspfv3LastAuthKeyExpiry	1.3.6.1.4.1.2011.5.25.147.0.13			An hwOspfv3LastAuthKeyExpiry notification indicates that the last key associated with an interface has expired. When this notification is received, either the lifetime of the key should be extended or a new key should be configured.
NTF hwOspfv3AuthSequenceNumWrap	1.3.6.1.4.1.2011.5.25.147.0.14			An hwOspfv3AuthSequenceNumWrap notification indicates that the 64-bit authentication sequence number has wrapped. When this notification is received, all the keys must be reset to avoid the possibility of replay attacks.
NTF hwOspfv3IntraAreaRouterIdConflictRecovered	1.3.6.1.4.1.2011.5.25.147.0.15			The object is used to monitor router ID conflict recovery in an intra area.
hwOspfv3Objects	1.3.6.1.4.1.2011.5.25.147.1
hwOspfv3GeneralGroup	1.3.6.1.4.1.2011.5.25.147.1.1
HWO hwOspfv3RouterId	1.3.6.1.4.1.2011.5.25.147.1.1.1	HWOspfv3RouterIdTc	read-write	A 32-bit integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses, represented as a 32-bit unsigned integer, if IPv4 is configured on the router.
STA hwOspfv3AdminStatus	1.3.6.1.4.1.2011.5.25.147.1.1.2	Status	read-write	The administrative status of OSPFv3 in the router. The value 'enabled' denotes that the OSPFv3 Process is active on at least one interface; 'disabled' disables it on all interfaces.
INT hwOspfv3VersionNumber	1.3.6.1.4.1.2011.5.25.147.1.1.3	INTEGER	read-only	The version number of OSPF for IPv6 is 3.
T/F hwOspfv3AreaBdrRtrStatus	1.3.6.1.4.1.2011.5.25.147.1.1.4	TruthValue	read-only	A flag to note whether this router is an area border router.
T/F hwOspfv3AsBdrRtrStatus	1.3.6.1.4.1.2011.5.25.147.1.1.5	TruthValue	read-write	A flag to note whether this router is configured as an Autonomous System border router.
G32 hwOspfv3AsScopeLsaCount	1.3.6.1.4.1.2011.5.25.147.1.1.6	Gauge32	read-only	The number of AS-Scope (e.g. AS-External) link state advertisements in the link state database.
U32 hwOspfv3AsScopeLsaCksumSum	1.3.6.1.4.1.2011.5.25.147.1.1.7	Unsigned32	read-only	The 32-bit unsigned sum of the LS checksums of the AS-scoped link state advertisements contained in the link state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
C32 hwOspfv3OriginateNewLsas	1.3.6.1.4.1.2011.5.25.147.1.1.8	Counter32	read-only	The number of new link-state advertisements that have been originated. This number is incremented each time the router originates a new LSA.
C32 hwOspfv3RxNewLsas	1.3.6.1.4.1.2011.5.25.147.1.1.9	Counter32	read-only	The number of link state advertisements received determined to be new instantiations. This number does not include newer instantiations of self-originated link state advertisements.
G32 hwOspfv3ExtLsaCount	1.3.6.1.4.1.2011.5.25.147.1.1.10	Gauge32	read-only	The number of AS-Scope External(LS type 0x4005) link state advertisements in the link state database
I32 hwOspfv3ExtAreaLsdbLimit	1.3.6.1.4.1.2011.5.25.147.1.1.11	Integer32	read-write	The maximum number of non-default AS-external-LSAs entries that can be stored in the link state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches ospfv3ExtAreaLsdbLimit, the router enters Overflow state. The router never holds more than ospfv3ExtAreaLsdbLimit non-default AS-external-LSAs in its database. Ospfv3ExtAreaLsdbLimit MUST be set identically in all routers attached to the OSPFv3 backbone and/or any regular OSPFv3 area. (i.e., OSPFv3 stub areas and NSSAs are excluded).
INT hwOspfv3RestartSupport	1.3.6.1.4.1.2011.5.25.147.1.1.12	INTEGER	read-write	The router's support for OSPFv3 Graceful restart. Options include: no restart support, only planned restarts or both planned and unplanned restarts.
NUM hwOspfv3RestartInterval	1.3.6.1.4.1.2011.5.25.147.1.1.13	HWOspfv3UpToRefreshIntervalTc	read-write	Configured OSPFv3 Graceful restart timeout interval.
INT hwOspfv3RestartStatus	1.3.6.1.4.1.2011.5.25.147.1.1.14	INTEGER	read-only	The current status of OSPFv3 Graceful restart capability.
NUM hwOspfv3RestartAge	1.3.6.1.4.1.2011.5.25.147.1.1.15	HWOspfv3UpToRefreshIntervalTc	read-only	Remaining time in current OSPFv3 Graceful restart interval.
INT hwOspfv3RestartExitRc	1.3.6.1.4.1.2011.5.25.147.1.1.16	INTEGER	read-only	Describes the outcome of the last attempt at a Graceful restart. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
T/F hwOspfv3NotificationEnable	1.3.6.1.4.1.2011.5.25.147.1.1.17	TruthValue	read-write	If this object is set to true(1), then it enables the generation of OSPFv3 Notifications. If it is set to false(2), these notifications are not generated. Configured values MUST survive an agent reboot.
U32 hwOspfv3ReferenceBandwidth	1.3.6.1.4.1.2011.5.25.147.1.1.18	Unsigned32	read-write	Reference bandwidth in kilobits per second for calculating default interface metrics. The default value is 100,000 KBPS (100 MBPS). This object is persistent, and when written, the entity SHOULD save the change to non-volatile storage.
hwOspfv3AreaTable	1.3.6.1.4.1.2011.5.25.147.1.2		not-accessible	Information describing the configured parameters and cumulative statistics of the router's attached areas.
hwOspfv3AreaEntry	1.3.6.1.4.1.2011.5.25.147.1.2.1		not-accessible	Information describing the configured parameters and cumulative statistics of one of the router's attached areas.
HWO hwOspfv3AreaId	1.3.6.1.4.1.2011.5.25.147.1.2.1.1	HWOspfv3AreaIdTc	not-accessible	A 32-bit integer uniquely identifying an area. Area ID 0 is used for the OSPFv3 backbone.
INT hwOspfv3AreaImportAsExtern	1.3.6.1.4.1.2011.5.25.147.1.2.1.2	INTEGER	read-create	Indicates whether an area is a Stub area, NSSA, or standard area. AS-scope LSAs are not imported into Stub Areas or NSSAs. NSSAs import AS-External data as NSSA LSAs which have Area-scope
C32 hwOspfv3AreaSpfRuns	1.3.6.1.4.1.2011.5.25.147.1.2.1.3	Counter32	read-only	The number of times that the intra-area route table has been calculated using this area's link state database. This is typically done using Dijkstra's algorithm.
G32 hwOspfv3AreaBdrRtrCount	1.3.6.1.4.1.2011.5.25.147.1.2.1.4	Gauge32	read-only	The total number of area border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
G32 hwOspfv3AreaAsBdrRtrCount	1.3.6.1.4.1.2011.5.25.147.1.2.1.5	Gauge32	read-only	The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
G32 hwOspfv3AreaScopeLsaCount	1.3.6.1.4.1.2011.5.25.147.1.2.1.6	Gauge32	read-only	The total number of Area-Scope link state advertisements in this area's link state database.
U32 hwOspfv3AreaScopeLsaCksumSum	1.3.6.1.4.1.2011.5.25.147.1.2.1.7	Unsigned32	read-only	The 32-bit unsigned sum of the Area-Scope link state advertisements' LS checksums contained in this area's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
INT hwOspfv3AreaSummary	1.3.6.1.4.1.2011.5.25.147.1.2.1.8	INTEGER	read-create	The variable ospfv3AreaSummary controls the import of Inter-Area LSAs into stub and NSSA areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate Inter-Area LSAs into the stub or NSSA area. It will rely entirely on its default route. If it is sendAreaSummary, the router will both summarize and propagate Inter-Area LSAs.
ROW hwOspfv3AreaRowStatus	1.3.6.1.4.1.2011.5.25.147.1.2.1.9	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
BIG hwOspfv3AreaStubMetric	1.3.6.1.4.1.2011.5.25.147.1.2.1.10	BigMetric	read-create	The metric value advertised for the default route into Stub and NSSA areas.
INT hwOspfv3AreaNssaTranslatorRole	1.3.6.1.4.1.2011.5.25.147.1.2.1.11	INTEGER	read-create	Indicates an NSSA border router's policy to perform NSSA translation of NSSA-LSAs into AS-External-LSAs.
INT hwOspfv3AreaNssaTranslatorState	1.3.6.1.4.1.2011.5.25.147.1.2.1.12	INTEGER	read-only	Indicates if and how an NSSA border router is performing NSSA translation of NSSA-LSAs into AS-External-LSAs. When this object is set to 'enabled', the NSSA border router's ospfv3AreaNssaTranslatorRole has been set to 'always'. When this object is set to 'elected', a candidate NSSA border router is translating NSSA-LSAs into AS-External-LSAs. When this object is set to 'disabled', a candidate NSSA Border router is NOT translating NSSA-LSAs into AS-External-LSAs.
U32 hwOspfv3AreaNssaTranslatorStabInterval	1.3.6.1.4.1.2011.5.25.147.1.2.1.13	Unsigned32	read-create	The stability interval defined as the number of seconds after an elected translator determines its services are no longer required that it should continue to perform its translation duties.
C32 hwOspfv3AreaNssaTranslatorEvents	1.3.6.1.4.1.2011.5.25.147.1.2.1.14	Counter32	read-only	Indicates the number of Translator state changes that have occurred since the last start-up of the OSPFv3 routing process. Discontinuities in the value of this counter can occur at re-initialization of the management system and at other times as indicated by the value of ospfv3DiscontinuityTime.
hwOspfv3AsLsdbTable	1.3.6.1.4.1.2011.5.25.147.1.3		not-accessible	The OSPFv3 Process's AS-Scope Link State Database.
hwOspfv3AsLsdbEntry	1.3.6.1.4.1.2011.5.25.147.1.3.1		not-accessible	A single AS-Scope Link State Advertisement.
U32 hwOspfv3AsLsdbType	1.3.6.1.4.1.2011.5.25.147.1.3.1.1	Unsigned32	not-accessible	The type of the link state advertisement. Each link state type has a separate advertisement format. AS-Scope LSAs not recognized by the router may be stored in the database.
HWO hwOspfv3AsLsdbRouterId	1.3.6.1.4.1.2011.5.25.147.1.3.1.2	HWOspfv3RouterIdTc	not-accessible	The 32 bit number that uniquely identifies the originating router in the Autonomous System.
U32 hwOspfv3AsLsdbLsId	1.3.6.1.4.1.2011.5.25.147.1.3.1.3	Unsigned32	not-accessible	The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
HWO hwOspfv3AsLsdbSequence	1.3.6.1.4.1.2011.5.25.147.1.3.1.4	HWOspfv3LsaSequenceTC	read-only	The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
HWO hwOspfv3AsLsdbAge	1.3.6.1.4.1.2011.5.25.147.1.3.1.5	HWOspfv3LsaAgeTC	read-only	This field is the age of the link state advertisement in seconds.
I32 hwOspfv3AsLsdbChecksum	1.3.6.1.4.1.2011.5.25.147.1.3.1.6	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT hwOspfv3AsLsdbAdvertisement	1.3.6.1.4.1.2011.5.25.147.1.3.1.7	OCTET STRING	read-only	The entire Link State Advertisement, including its header.
T/F hwOspfv3AsLsdbTypeKnown	1.3.6.1.4.1.2011.5.25.147.1.3.1.8	TruthValue	read-only	Indicates whether the LSA type is recognized by this Router.
hwOspfv3AreaLsdbTable	1.3.6.1.4.1.2011.5.25.147.1.4		not-accessible	The OSPFv3 Process's Area-Scope Link State Database.
hwOspfv3AreaLsdbEntry	1.3.6.1.4.1.2011.5.25.147.1.4.1		not-accessible	A single Area-Scope Link State Advertisement.
HWO hwOspfv3AreaLsdbAreaId	1.3.6.1.4.1.2011.5.25.147.1.4.1.1	HWOspfv3AreaIdTc	not-accessible	The 32-bit identifier of the Area from which the LSA was received.
U32 hwOspfv3AreaLsdbType	1.3.6.1.4.1.2011.5.25.147.1.4.1.2	Unsigned32	not-accessible	The type of the link state advertisement. Each link state type has a separate advertisement format. Area-Scope LSAs unrecognized by the router are also stored in this database.
HWO hwOspfv3AreaLsdbRouterId	1.3.6.1.4.1.2011.5.25.147.1.4.1.3	HWOspfv3RouterIdTc	not-accessible	The 32-bit number that uniquely identifies the originating router in the Autonomous System.
U32 hwOspfv3AreaLsdbLsId	1.3.6.1.4.1.2011.5.25.147.1.4.1.4	Unsigned32	not-accessible	The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
HWO hwOspfv3AreaLsdbSequence	1.3.6.1.4.1.2011.5.25.147.1.4.1.5	HWOspfv3LsaSequenceTC	read-only	The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
HWO hwOspfv3AreaLsdbAge	1.3.6.1.4.1.2011.5.25.147.1.4.1.6	HWOspfv3LsaAgeTC	read-only	This field is the age of the link state advertisement in seconds.
I32 hwOspfv3AreaLsdbChecksum	1.3.6.1.4.1.2011.5.25.147.1.4.1.7	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT hwOspfv3AreaLsdbAdvertisement	1.3.6.1.4.1.2011.5.25.147.1.4.1.8	OCTET STRING	read-only	The entire Link State Advertisement, including its header.
T/F hwOspfv3AreaLsdbTypeKnown	1.3.6.1.4.1.2011.5.25.147.1.4.1.9	TruthValue	read-only	Indicates whether the LSA type is recognized by this Router.
hwOspfv3LinkLsdbTable	1.3.6.1.4.1.2011.5.25.147.1.5		not-accessible	The OSPFv3 Process's Link-Scope Link State Database.
hwOspfv3LinkLsdbEntry	1.3.6.1.4.1.2011.5.25.147.1.5.1		not-accessible	A single Link-Scope Link State Advertisement.
NUM hwOspfv3LinkLsdbIfIndex	1.3.6.1.4.1.2011.5.25.147.1.5.1.1	InterfaceIndex	not-accessible	The identifier of the link from which the LSA was received.
HWO hwOspfv3LinkLsdbIfInstId	1.3.6.1.4.1.2011.5.25.147.1.5.1.2	HWOspfv3IfInstIdTc	not-accessible	The identifier of the interface instance from which the LSA was received.
U32 hwOspfv3LinkLsdbType	1.3.6.1.4.1.2011.5.25.147.1.5.1.3	Unsigned32	not-accessible	The type of the link state advertisement. Each link state type has a separate advertisement format. Link-Scope LSAs unrecognized by the router are also stored in this database.
HWO hwOspfv3LinkLsdbRouterId	1.3.6.1.4.1.2011.5.25.147.1.5.1.4	HWOspfv3RouterIdTc	not-accessible	The 32 bit number that uniquely identifies the originating router in the Autonomous System.
HWO hwOspfv3LinkLsdbLsId	1.3.6.1.4.1.2011.5.25.147.1.5.1.5	HWOspfv3LsIdTC	not-accessible	The Link State ID is an LS Type Specific field containing a unique identifier; it identifies the piece of the routing domain that is being described by the advertisement. In contrast to OSPFv2, the LSID has no addressing semantics.
HWO hwOspfv3LinkLsdbSequence	1.3.6.1.4.1.2011.5.25.147.1.5.1.6	HWOspfv3LsaSequenceTC	read-only	The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
HWO hwOspfv3LinkLsdbAge	1.3.6.1.4.1.2011.5.25.147.1.5.1.7	HWOspfv3LsaAgeTC	read-only	This field is the age of the link state advertisement in seconds.
I32 hwOspfv3LinkLsdbChecksum	1.3.6.1.4.1.2011.5.25.147.1.5.1.8	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT hwOspfv3LinkLsdbAdvertisement	1.3.6.1.4.1.2011.5.25.147.1.5.1.9	OCTET STRING	read-only	The entire Link State Advertisement, including its header.
T/F hwOspfv3LinkLsdbTypeKnown	1.3.6.1.4.1.2011.5.25.147.1.5.1.10	TruthValue	read-only	Indicates whether the LSA type is recognized by this Router.
hwOspfv3IfTable	1.3.6.1.4.1.2011.5.25.147.1.6		not-accessible	The OSPFv3 Interface Table describes the interfaces from the viewpoint of OSPFv3.
hwOspfv3IfEntry	1.3.6.1.4.1.2011.5.25.147.1.6.1		not-accessible	The OSPFv3 Interface Entry describes one interface from the viewpoint of OSPFv3.
NUM hwOspfv3IfIndex	1.3.6.1.4.1.2011.5.25.147.1.6.1.1	InterfaceIndex	not-accessible	The interface index of this OSPFv3 interface. It corresponds to the interface index of the IPv6 interface on which OSPFv3 is configured.
HWO hwOspfv3IfInstId	1.3.6.1.4.1.2011.5.25.147.1.6.1.2	HWOspfv3IfInstIdTc	not-accessible	Enables multiple interface instances of OSPFv3 to be run over a single link. Each protocol instance would be assigned a separate ID. This ID has local link significance only.
HWO hwOspfv3IfAreaId	1.3.6.1.4.1.2011.5.25.147.1.6.1.3	HWOspfv3AreaIdTc	read-create	A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0 is used for the OSPFv3 backbone.
INT hwOspfv3IfType	1.3.6.1.4.1.2011.5.25.147.1.6.1.4	INTEGER	read-create	The OSPFv3 interface type.
STA hwOspfv3IfAdminStatus	1.3.6.1.4.1.2011.5.25.147.1.6.1.5	Status	read-create	The OSPFv3 interface's administrative status. The value formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPFv3.
DES hwOspfv3IfRtrPriority	1.3.6.1.4.1.2011.5.25.147.1.6.1.6	DesignatedRouterPriority	read-create	The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker.
NUM hwOspfv3IfTransitDelay	1.3.6.1.4.1.2011.5.25.147.1.6.1.7	HWOspfv3UpToRefreshIntervalTc	read-create	The estimated number of seconds it takes to transmit a link state update packet over this interface.
NUM hwOspfv3IfRetransInterval	1.3.6.1.4.1.2011.5.25.147.1.6.1.8	HWOspfv3UpToRefreshIntervalTc	read-create	The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets.
HWH hwOspfv3IfHelloInterval	1.3.6.1.4.1.2011.5.25.147.1.6.1.9	HWHelloRange	read-create	The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
NUM hwOspfv3IfRtrDeadInterval	1.3.6.1.4.1.2011.5.25.147.1.6.1.10	HWOspfv3DeadIntRangeTc	read-create	The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down on the interface. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
INT hwOspfv3IfState	1.3.6.1.4.1.2011.5.25.147.1.6.1.11	INTEGER	read-only	The OSPFv3 Interface State.
HWO hwOspfv3IfDesignatedRouter	1.3.6.1.4.1.2011.5.25.147.1.6.1.12	HWOspfv3RouterIdTc	read-only	The Router ID of the Designated Router.
HWO hwOspfv3IfBackupDesignatedRouter	1.3.6.1.4.1.2011.5.25.147.1.6.1.13	HWOspfv3RouterIdTc	read-only	The Router ID of the Backup Designated Router.
C32 hwOspfv3IfEvents	1.3.6.1.4.1.2011.5.25.147.1.6.1.14	Counter32	read-only	The number of times this OSPFv3 interface has changed its state, or an error has occurred.
ROW hwOspfv3IfRowStatus	1.3.6.1.4.1.2011.5.25.147.1.6.1.15	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
MET hwOspfv3IfMetricValue	1.3.6.1.4.1.2011.5.25.147.1.6.1.16	Metric	read-create	The metric assigned to this interface. The default value of the Metric is Reference Bandwidth / ifSpeed. The value of the reference bandwidth is configured by the ospfv3ReferenceBandwidth object.
G32 hwOspfv3IfLinkScopeLsaCount	1.3.6.1.4.1.2011.5.25.147.1.6.1.17	Gauge32	read-only	The total number of Link-Scope link state advertisements in this link's link state database.
U32 hwOspfv3IfLinkLsaCksumSum	1.3.6.1.4.1.2011.5.25.147.1.6.1.18	Unsigned32	read-only	The 32-bit unsigned sum of the Link-Scope link state advertisements' LS checksums contained in this link's link state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
U32 hwOspfv3IfPollInterval	1.3.6.1.4.1.2011.5.25.147.1.6.1.19	Unsigned32	read-create	The larger time interval, in seconds, between the Hello packets sent to an inactive non-broadcast multi-access neighbor.
INT hwOspfv3IfMulticastForwarding	1.3.6.1.4.1.2011.5.25.147.1.6.1.20	INTEGER	read-create	The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link unicasts. Data link multicasting is not meaningful on point to point and NBMA interfaces, and setting ospfv3MulticastForwarding to 0 effectively disables all multicast forwarding.
hwOspfv3VirtIfTable	1.3.6.1.4.1.2011.5.25.147.1.7		not-accessible	Information about this router's virtual interfaces.
hwOspfv3VirtIfEntry	1.3.6.1.4.1.2011.5.25.147.1.7.1		not-accessible	Information about a single Virtual Interface.
HWO hwOspfv3VirtIfAreaId	1.3.6.1.4.1.2011.5.25.147.1.7.1.1	HWOspfv3AreaIdTc	not-accessible	The Transit Area that the Virtual Link traverses. By definition, this is not Area 0
HWO hwOspfv3VirtIfNeighbor	1.3.6.1.4.1.2011.5.25.147.1.7.1.2	HWOspfv3RouterIdTc	not-accessible	The Router ID of the Virtual Neighbor.
NUM hwOspfv3VirtIfIndex	1.3.6.1.4.1.2011.5.25.147.1.7.1.3	InterfaceIndex	read-only	The local interface index assigned to this OSPFv3 virtual interface. It is advertised in Hello's sent over the virtual link and in the router's router-LSAs.
HWO hwOspfv3VirtIfInstId	1.3.6.1.4.1.2011.5.25.147.1.7.1.4	HWOspfv3IfInstIdTc	read-only	Specifies the interface instance ID to be used for the virtual interface. This ID has local link significance only.
NUM hwOspfv3VirtIfTransitDelay	1.3.6.1.4.1.2011.5.25.147.1.7.1.5	HWOspfv3UpToRefreshIntervalTc	read-create	The estimated number of seconds it takes to transmit a link state update packet over this interface.
NUM hwOspfv3VirtIfRetransInterval	1.3.6.1.4.1.2011.5.25.147.1.7.1.6	HWOspfv3UpToRefreshIntervalTc	read-create	The number of seconds between link state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link state request packets. This value should be well over the expected round-trip time.
HEL hwOspfv3VirtIfHelloInterval	1.3.6.1.4.1.2011.5.25.147.1.7.1.7	HelloRange	read-create	The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.
NUM hwOspfv3VirtIfRtrDeadInterval	1.3.6.1.4.1.2011.5.25.147.1.7.1.8	HWOspfv3DeadIntRangeTc	read-create	The number of seconds that a router's Hello packets have not been seen before its neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.
INT hwOspfv3VirtIfState	1.3.6.1.4.1.2011.5.25.147.1.7.1.9	INTEGER	read-only	OSPFv3 virtual interface states. The same encoding as the hwOspfv3IfTable is used.
C32 hwOspfv3VirtIfEvents	1.3.6.1.4.1.2011.5.25.147.1.7.1.10	Counter32	read-only	The number of state changes or error events on this Virtual Link
ROW hwOspfv3VirtIfRowStatus	1.3.6.1.4.1.2011.5.25.147.1.7.1.11	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
G32 hwOspfv3VirtIfLinkScopeLsaCount	1.3.6.1.4.1.2011.5.25.147.1.7.1.12	Gauge32	read-only	The total number of Link-Scope link state advertisements in this virtual link's link state database.
U32 hwOspfv3VirtIfLinkLsaCksumSum	1.3.6.1.4.1.2011.5.25.147.1.7.1.13	Unsigned32	read-only	The 32-bit unsigned sum of the Link-Scope link-state advertisements' LS checksums contained in this virtual link's link-state database. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link state database of two routers.
hwOspfv3NbrTable	1.3.6.1.4.1.2011.5.25.147.1.8		not-accessible	A table of non-virtual neighbor information.
hwOspfv3NbrEntry	1.3.6.1.4.1.2011.5.25.147.1.8.1		not-accessible	The information regarding a single neighbor.
NUM hwOspfv3NbrIfIndex	1.3.6.1.4.1.2011.5.25.147.1.8.1.1	InterfaceIndex	not-accessible	The local link ID of the link over which the neighbor can be reached.
HWO hwOspfv3NbrIfInstId	1.3.6.1.4.1.2011.5.25.147.1.8.1.2	HWOspfv3IfInstIdTc	not-accessible	Interface instance over which the neighbor can be reached. This ID has local link significance only.
HWO hwOspfv3NbrRtrId	1.3.6.1.4.1.2011.5.25.147.1.8.1.3	HWOspfv3RouterIdTc	not-accessible	A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
IPt hwOspfv3NbrAddressType	1.3.6.1.4.1.2011.5.25.147.1.8.1.4	InetAddressType	read-only	The address type of ospfv3NbrAddress. Only IPv6 addresses without zone index are expected.
IP hwOspfv3NbrAddress	1.3.6.1.4.1.2011.5.25.147.1.8.1.5	InetAddress	read-only	The IPv6 address of the neighbor associated with the local link.
I32 hwOspfv3NbrOptions	1.3.6.1.4.1.2011.5.25.147.1.8.1.6	Integer32	read-only	A Bit Mask corresponding to the neighbor's options field.
DES hwOspfv3NbrPriority	1.3.6.1.4.1.2011.5.25.147.1.8.1.7	DesignatedRouterPriority	read-only	The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.
INT hwOspfv3NbrState	1.3.6.1.4.1.2011.5.25.147.1.8.1.8	INTEGER	read-only	The State of the relationship with this Neighbor.
C32 hwOspfv3NbrEvents	1.3.6.1.4.1.2011.5.25.147.1.8.1.9	Counter32	read-only	The number of times this neighbor relationship has changed state, or an error has occurred.
G32 hwOspfv3NbrLsRetransQLen	1.3.6.1.4.1.2011.5.25.147.1.8.1.10	Gauge32	read-only	The current length of the retransmission queue.
T/F hwOspfv3NbrHelloSuppressed	1.3.6.1.4.1.2011.5.25.147.1.8.1.11	TruthValue	read-only	Indicates whether Hellos are being suppressed to the neighbor
NUM hwOspfv3NbrIfId	1.3.6.1.4.1.2011.5.25.147.1.8.1.12	InterfaceIndex	read-only	The interface ID that the neighbor advertises in its Hello Packets on this link, that is, the neighbor's local interface index.
INT hwOspfv3NbrRestartHelperStatus	1.3.6.1.4.1.2011.5.25.147.1.8.1.13	INTEGER	read-only	Indicates whether the router is acting as a Graceful restart helper for the neighbor.
NUM hwOspfv3NbrRestartHelperAge	1.3.6.1.4.1.2011.5.25.147.1.8.1.14	HWOspfv3UpToRefreshIntervalTc	read-only	Remaining time in current OSPFv3 Graceful restart interval, if the router is acting as a restart helper for the neighbor.
INT hwOspfv3NbrRestartHelperExitRc	1.3.6.1.4.1.2011.5.25.147.1.8.1.15	INTEGER	read-only	Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
hwOspfv3CfgNbrTable	1.3.6.1.4.1.2011.5.25.147.1.9		not-accessible	A table of configured, non-virtual neighbor information.
hwOspfv3CfgNbrEntry	1.3.6.1.4.1.2011.5.25.147.1.9.1		not-accessible	The information regarding a single configured neighbor or neighbor discovered by lower-level protocols such as Inverse Neighbor Discovery.
NUM hwOspfv3CfgNbrIfIndex	1.3.6.1.4.1.2011.5.25.147.1.9.1.1	InterfaceIndex	not-accessible	The local link ID of the link over which the neighbor can be reached.
HWO hwOspfv3CfgNbrIfInstId	1.3.6.1.4.1.2011.5.25.147.1.9.1.2	HWOspfv3IfInstIdTc	not-accessible	Interface instance over which the neighbor can be reached. This ID has local link significance only.
HWO hwOspfv3CfgNbrRtrId	1.3.6.1.4.1.2011.5.25.147.1.9.1.3	HWOspfv3RouterIdTc	not-accessible	A 32-bit integer uniquely identifying the static neighbor router in the Autonomous System.
DES hwOspfv3CfgNbrPriority	1.3.6.1.4.1.2011.5.25.147.1.9.1.4	DesignatedRouterPriority	read-create	The priority of this neighbor in the designated router election algorithm. The value 0 signifies that the neighbor is not eligible to become the designated router on this particular network.
ROW hwOspfv3CfgNbrRowStatus	1.3.6.1.4.1.2011.5.25.147.1.9.1.5	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
hwOspfv3VirtNbrTable	1.3.6.1.4.1.2011.5.25.147.1.10		not-accessible	A table of virtual neighbor information.
hwOspfv3VirtNbrEntry	1.3.6.1.4.1.2011.5.25.147.1.10.1		not-accessible	Virtual neighbor information.
HWO hwOspfv3VirtNbrArea	1.3.6.1.4.1.2011.5.25.147.1.10.1.1	HWOspfv3AreaIdTc	not-accessible	The Transit Area Identifier.
HWO hwOspfv3VirtNbrRtrId	1.3.6.1.4.1.2011.5.25.147.1.10.1.2	HWOspfv3RouterIdTc	not-accessible	A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
NUM hwOspfv3VirtNbrIfIndex	1.3.6.1.4.1.2011.5.25.147.1.10.1.3	InterfaceIndex	read-only	The local interface ID for the virtual link over which the neighbor can be reached.
HWO hwOspfv3VirtNbrIfInstId	1.3.6.1.4.1.2011.5.25.147.1.10.1.4	HWOspfv3IfInstIdTc	read-only	The interface instance for the virtual link over which the neighbor can be reached.
IPt hwOspfv3VirtNbrAddressType	1.3.6.1.4.1.2011.5.25.147.1.10.1.5	InetAddressType	read-only	The address type of ospfv3VirtNbrAddress. Only IPv6 addresses without zone index are expected.
IP hwOspfv3VirtNbrAddress	1.3.6.1.4.1.2011.5.25.147.1.10.1.6	InetAddress	read-only	The IPv6 address advertised by this Virtual Neighbor. It must be a Global scope address.
I32 hwOspfv3VirtNbrOptions	1.3.6.1.4.1.2011.5.25.147.1.10.1.7	Integer32	read-only	A Bit Mask corresponding to the neighbor's options field.
INT hwOspfv3VirtNbrState	1.3.6.1.4.1.2011.5.25.147.1.10.1.8	INTEGER	read-only	The state of the Virtual Neighbor Relationship.
C32 hwOspfv3VirtNbrEvents	1.3.6.1.4.1.2011.5.25.147.1.10.1.9	Counter32	read-only	The number of times this virtual link has changed its state, or an error has occurred.
G32 hwOspfv3VirtNbrLsRetransQLen	1.3.6.1.4.1.2011.5.25.147.1.10.1.10	Gauge32	read-only	The current length of the retransmission queue.
T/F hwOspfv3VirtNbrHelloSuppressed	1.3.6.1.4.1.2011.5.25.147.1.10.1.11	TruthValue	read-only	Indicates whether Hellos are being suppressed to the neighbor
NUM hwOspfv3VirtNbrIfId	1.3.6.1.4.1.2011.5.25.147.1.10.1.12	InterfaceIndex	read-only	The interface ID that the neighbor advertises in its Hello Packets on this virtual link, that is, the neighbor's local interface ID.
INT hwOspfv3VirtNbrRestartHelperStatus	1.3.6.1.4.1.2011.5.25.147.1.10.1.13	INTEGER	read-only	Indicates whether the router is acting as a Graceful restart helper for the neighbor.
NUM hwOspfv3VirtNbrRestartHelperAge	1.3.6.1.4.1.2011.5.25.147.1.10.1.14	HWOspfv3UpToRefreshIntervalTc	read-only	Remaining time in current OSPFv3 Graceful restart interval, if the router is acting as a restart helper for the neighbor.
INT hwOspfv3VirtNbrRestartHelperExitRc	1.3.6.1.4.1.2011.5.25.147.1.10.1.15	INTEGER	read-only	Describes the outcome of the last attempt at acting as a Graceful restart helper for the neighbor. none:............no restart has yet been attempted. inProgress:......a restart attempt is currently underway. completed:.......the last restart completed successfully. timedOut:........the last restart timed out. topologyChanged:.the last restart was aborted due to a topology change.
hwOspfv3AreaAggregateTable	1.3.6.1.4.1.2011.5.25.147.1.11		not-accessible	A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one.
hwOspfv3AreaAggregateEntry	1.3.6.1.4.1.2011.5.25.147.1.11.1		not-accessible	A range of IPv6 prefixes specified by a prefix/prefix length pair. Note that if ranges are configured such that one range subsumes another range the most specific match is the preferred one.
HWO hwOspfv3AreaAggregateAreaId	1.3.6.1.4.1.2011.5.25.147.1.11.1.1	HWOspfv3AreaIdTc	not-accessible	The Area the Address Aggregate is to be found within.
INT hwOspfv3AreaAggregateAreaLsdbType	1.3.6.1.4.1.2011.5.25.147.1.11.1.2	INTEGER	not-accessible	The type of the Address Aggregate. This field specifies the Area Lsdb type that this Address Aggregate applies to.
IPt hwOspfv3AreaAggregatePrefixType	1.3.6.1.4.1.2011.5.25.147.1.11.1.4	InetAddressType	not-accessible	The prefix type of ospfv3AreaAggregatePrefix. Only IPv6 addresses are expected.
IP hwOspfv3AreaAggregatePrefix	1.3.6.1.4.1.2011.5.25.147.1.11.1.5	InetAddress	not-accessible	The IPv6 Prefix.
ADR hwOspfv3AreaAggregatePrefixLength	1.3.6.1.4.1.2011.5.25.147.1.11.1.6	InetAddressPrefixLength	not-accessible	The length of the prefix (in bits). A prefix can not be shorter than 0 bits.
ROW hwOspfv3AreaAggregateRowStatus	1.3.6.1.4.1.2011.5.25.147.1.11.1.7	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation, construction and destruction. The value of this object has no effect on whether other objects in this conceptual row can be modified.
INT hwOspfv3AreaAggregateEffect	1.3.6.1.4.1.2011.5.25.147.1.11.1.8	INTEGER	read-create	Prefixes subsumed by ranges either trigger the advertisement of the indicated aggregate (advertiseMatching), or result in the prefix not being advertised at all outside the area.
hwOspfv3NotificationEntry	1.3.6.1.4.1.2011.5.25.147.1.12
INT hwOspfv3ConfigErrorType	1.3.6.1.4.1.2011.5.25.147.1.12.1	INTEGER	accessible-for-notify	Potential types of configuration conflicts. Used by the ospfv3ConfigError and ospfv3ConfigVirtError notifications. When the last value of a notification using this object is needed, but no notifications of that type have been sent, this value pertaining to this object should be returned as noError
INT hwOspfv3PacketType	1.3.6.1.4.1.2011.5.25.147.1.12.2	INTEGER	accessible-for-notify	OSPFv3 packet types. When the last value of a notification using this object is needed, but no notifications of that type have been sent, the value pertaining to this object should be returned as nullPacket
IP hwOspfv3PacketSrc	1.3.6.1.4.1.2011.5.25.147.1.12.3	InetAddress	accessible-for-notify	The IPv6 address of an inbound packet that cannot be identified by a neighbor instance. When the last value of a notification using this object is needed, but no notifications of that type have been sent, the value pertaining to this object should be returned as 0. Only IPv6 addresses without zone index are expected.
OCT hwOspfv3IfName	1.3.6.1.4.1.2011.5.25.147.1.12.4	OCTET STRING	accessible-for-notify	The interface name
INT hwOspfv3IfStateChgReason	1.3.6.1.4.1.2011.5.25.147.1.12.5	INTEGER	accessible-for-notify	Interface state change reason.
INT hwOspfv3NbrStateChgReason	1.3.6.1.4.1.2011.5.25.147.1.12.6	INTEGER	accessible-for-notify	Neighbor state change reason.
I32 hwOspfv3ProcessId	1.3.6.1.4.1.2011.5.25.147.1.12.7	Integer32	read-only	The process ID indicates the OSPFv3 process number. The value ranges from 1 to 65535.
HWO hwOspfv3AreaIdIndex	1.3.6.1.4.1.2011.5.25.147.1.12.8	HWOspfv3AreaIdTc	read-only	A 32-bit integer uniquely identifying an area. Area ID 0 is used for the OSPFv3 backbone.
HWO hwOspfv3NewRouterId	1.3.6.1.4.1.2011.5.25.147.1.12.9	HWOspfv3RouterIdTc	read-only	A 32-bit integer uniquely identifying the router in the Autonomous System. To ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses, represented as a 32-bit unsigned integer, if IPv4 is configured on the router.
hwOspfv3Conformance	1.3.6.1.4.1.2011.5.25.147.2
hwOspfv3Groups	1.3.6.1.4.1.2011.5.25.147.2.1
hwOspfv3BasicGroup	1.3.6.1.4.1.2011.5.25.147.2.1.1			These objects are used for managing/monitoring OSPFv3 global parameters.
hwOspfv3AreaGroup	1.3.6.1.4.1.2011.5.25.147.2.1.2			These objects are used for OSPFv3 systems supporting areas.
hwOspfv3AsLsdbGroup	1.3.6.1.4.1.2011.5.25.147.2.1.3			These objects are used for OSPFv3 systems that display their AS-scope link state database.
hwOspfv3AreaLsdbGroup	1.3.6.1.4.1.2011.5.25.147.2.1.4			These objects are used for OSPFv3 systems that display their Area-scope link state database.
hwOspfv3LinkLsdbGroup	1.3.6.1.4.1.2011.5.25.147.2.1.5			These objects are used for OSPFv3 systems that display their Link-scope link state database.
hwOspfv3IfGroup	1.3.6.1.4.1.2011.5.25.147.2.1.6			These interface objects used for managing/monitoring OSPFv3 interfaces.
hwOspfv3VirtIfGroup	1.3.6.1.4.1.2011.5.25.147.2.1.7			These virtual interface objects are used for managing/monitoring OSPFv3 virtual interfaces.
hwOspfv3NbrGroup	1.3.6.1.4.1.2011.5.25.147.2.1.8			These neighbor objects are used for managing/monitoring OSPFv3 neighbors.
hwOspfv3CfgNbrGroup	1.3.6.1.4.1.2011.5.25.147.2.1.9			These configured neighbor objects are used for managing/monitoring OSPFv3 configured neighbors.
hwOspfv3VirtNbrGroup	1.3.6.1.4.1.2011.5.25.147.2.1.10			These virtual neighbor objects are used for managing/monitoring OSPFv3 virtual neighbors.
hwOspfv3AreaAggregateGroup	1.3.6.1.4.1.2011.5.25.147.2.1.11			These area aggregate objects used required for aggregating OSPFv3 prefixes for summarization across areas.
hwOspfv3NotificationObjectGroup	1.3.6.1.4.1.2011.5.25.147.2.1.12			These objects are used to record notification parameters
hwOspfv3NotificationGroup	1.3.6.1.4.1.2011.5.25.147.2.1.13			This group is used for OSPFv3 notifications
hwOspfv3Compliances	1.3.6.1.4.1.2011.5.25.147.2.2
hwOspfv3Compliance	1.3.6.1.4.1.2011.5.25.147.2.2.1			The compliance statement
hwOspfv3ReadOnlyCompliance	1.3.6.1.4.1.2011.5.25.147.2.2.2			When this MIB module is implemented without support for read-create (i.e., in read-only mode), the implementation can claim read-only compliance. Such a device can then be monitored, but cannot be configured with this MIB.

RFC description

Monitors OSPFv3 routing protocol configuration, neighbors, and adjacencies on Huawei devices.

Start monitoring Huawei router running OSPFv3/IPv6 with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-OSPFV3-MIB

What Is HUAWEI-OSPFV3-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description