All MIBs › HPN-ICF-LswINF-MIB
Last Updated: 2001-06-29
Category: Network Interfaces, Technology: Switching/L2, Vendor: H3C/HH3C, Vendor: HP/HPE
Description: Handles configuration of Layer 2 switch ports on HP/Comware switches, covering speed, duplex mode, and flow control.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HPN-ICF-LswINF-MIB?
HPN-ICF-LswINF-MIB is an HP/H3C Comware private MIB (part of the ICF Layer 2 switch family) that extends standard interface management with switch-specific Layer 2 port attributes. Its hpnicfifXXTable carries per-port flags (aggregate/mirror/isolated port, VLAN type, flow control) plus broadcast/multicast/unicast storm-suppression controls in both percentage and packets-per-second modes, and payload/error packet counters (hpnicfifInPayloadOctets, hpnicfifInErrorPktsRate, hpnicfifOutPkts). Companion tables cover link aggregation (hpnicfifAggregateTable), hybrid-port VLAN tagging bitmaps (hpnicfifHybridPortTable), combo fiber/copper port state (hpnicfifComboPortTable), and packet-buffer allocation per interface (hpnicfifPktBufTable, including hpnicfifPktBufMiss for buffer-starvation events). A separate hpnicfethernetTable exposes duplex, speed, MDI mode, MAC-learning limits/mode, and per-port Ethernet flow statistics. Because it layers switch-specific detail on top of standard IF-MIB ifIndex entries, it is deployed alongside IF-MIB on HP/H3C ICF-based switches for HPN-ICF-LswINF-MIB MIB based Layer 2 port diagnostics.
IPNetwork Monitor allows you to monitor SNMP objects defined in HPN-ICF-LswINF-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HP/H3C Comware-based ICF switches
Monitoring Examples
An operator polls hpnicfifInErrorPktsRate and hpnicfifPktBufMiss for a given ifIndex to check whether a switch port is dropping packets due to buffer exhaustion, and checks hpnicfifUniSuppression/hpnicfifMulSuppression against configured thresholds; a climbing hpnicfifPktBufMiss counter alongside high hpnicfifInErrorPktsRate would point to an oversubscribed or misconfigured port suppressing legitimate traffic.
What Can Be Monitored
- storm-suppression thresholds (unicast/multicast, ratio and pps)
- packet-buffer allocation and miss counters
- link-aggregation port list/mode
- combo/hybrid port state
- Ethernet duplex/speed/MDI settings
- per-port payload and error packet counters
This MIB depends on
Related MIBs
Imported Objects
From HPN-ICF-OID-MIB
| hpnicflswCommon | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex | |
| ifIndex | OBJECT-TYPE |
From SNMPv2-SMI
| Counter64 | |
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using hpnicfifOutPayloadOctets OID:
Select an HP/H3C Comware-based ICF switch (Layer 2 port attributes/storm suppression) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpnicfifOutPayloadOctets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The actual output octets of the interface. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| INT hpnicfBpduTunnelStatus | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.8 | INTEGER | read-write | Bpdu tunnel enable status. |
| hpnicfethernetEntry | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1 | not-accessible | Entries of Ethernet port attribute table | |
| hpnicfethernetTable | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4 | not-accessible | Ethernet port attribute table. | |
| INT hpnicfGlobalBroadcastMaxPps | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.6 | INTEGER | read-write | The global max packets per second. When it is set, the value of BroadcastMaxPps in all ports will be changed to that setting. |
| INT hpnicfGlobalBroadcastMaxRatio | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.7 | INTEGER | read-write | The global max-ratio of broadcast from 0 to 100 percent. When it is set, the value of BroadcastMaxRatio in all ports will be changed to that setting. |
| hpnicfifAggregateEntry | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.2.1 | not-accessible | Port aggregation information table. | |
| INT hpnicfifAggregateModel | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.2.1.4 | INTEGER | read-write | Load sharing mode for the port aggregation. |
| ROW hpnicfifAggregateOperStatus | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.2.1.5 | RowStatus | read-create | Current operation status of the row. |
| T/F hpnicfifAggregatePort | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.3 | TruthValue | read-only | Whether it is the aggregated port. (if the port participates in the aggregation, this value is true.) |
| NUM hpnicfifAggregatePortIndex | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.2.1.1 | InterfaceIndex | read-only | Index number of the main aggregated port. |
| POR hpnicfifAggregatePortListPorts | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.2.1.3 | PortList | read-write | Portlist of a aggregating. |
| OCT hpnicfifAggregatePortName | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.2.1.2 | OCTET STRING | read-write | Aggregation group name. |
| hpnicfifAggregateTable | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.2 | not-accessible | Port aggregation information table. | |
| I32 hpnicfifBKbpsMulSuppression | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.27 | Integer32 | read-write | With bandwidth-based multicast suppression, the bandwidth is measured in Kbps. The upper limit of the multicast suppession with bandwidth-based(Kbps) is the value of hpnicfifBKbpsMulSuppressionMax in the entry. The value of hpnicfifBKbpsMulSuppression must be multiple of the value of hpnicfifBKbpsMulSuppressionStep. The default value of hpnicfifBKbpsMulSuppression is the value of hpnicfifBKbpsMulSuppressionMax. |
| I32 hpnicfifBKbpsMulSuppressionMax | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.25 | Integer32 | read-only | The maximum value of the multicast suppression with bandwidth-based(Kbps) that a port can be configured. |
| I32 hpnicfifBKbpsMulSuppressionStep | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.26 | Integer32 | read-only | The step of multicast suppression with bandwidth-based(Kbps). |
| I32 hpnicfifBKbpsUniSuppression | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.34 | Integer32 | read-write | With bandwidth-based unicast suppression, the bandwidth is measured in Kbps. The upper limit of the unicast suppession with bandwidth-based(Kbps) is the value of hpnicfifBKbpsUniSuppressionMax in the entry. The value of hpnicfifBKbpsUniSuppression must be multiple of the value of hpnicfifBKbpsUniSuppressionStep. The default value of hpnicfifBKbpsUniSuppression is the value of hpnicfifBKbpsUniSuppressionMax. |
| I32 hpnicfifBKbpsUniSuppressionMax | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.32 | Integer32 | read-only | The maximum value of the unicast suppression with bandwidth-based (Kbps) that a port can be configured. |
| I32 hpnicfifBKbpsUniSuppressionStep | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.33 | Integer32 | read-only | The step of unicast suppression with bandwidth-based(Kbps). |
| I32 hpnicfifBMbpsMulSuppression | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.24 | Integer32 | read-write | With bandwidth-based multicast suppression, the bandwidth is measured in Mbps. The upper limit of the multicast suppession with bandwidth-based(Mbps) is the value of hpnicfifBMbpsMulSuppressionMax in the entry. The default value of hpnicfifBMbpsMulSuppression is the value of hpnicfifBMbpsMulSuppressionMax. |
| I32 hpnicfifBMbpsMulSuppressionMax | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.23 | Integer32 | read-only | The maximum value of the multicast suppression with bandwidth-based(Mbps) that a port can be configured. |
| I32 hpnicfifBMbpsUniSuppression | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.31 | Integer32 | read-write | With bandwidth-based Unicast suppression, the bandwidth is measured in Mbps. The upper limit of the unicast suppession with bandwidth-based(Mbps) is the value of hpnicfifBMbpsUniSuppressionMax in the entry. The default value of hpnicfifBMbpsUniSuppression is the value of hpnicfifBMbpsUniSuppressionMax. |
| I32 hpnicfifBMbpsUniSuppressionMax | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.30 | Integer32 | read-only | The maximum value of the unicast suppression with bandwidth-based (Mbps) that a port can be configured. |
| INT hpnicfifClearStat | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.9 | INTEGER | read-write | Clear specify port statistics. Operation read is not supported. |
| INT hpnicfifComboActivePort | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.22 | INTEGER | read-write | Active port on combo interface. |
| INT hpnicfifComboPortCurActive | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.4.1.2 | INTEGER | read-write | Current active interface of combo interfaces. The value 'fiber' means the interface with fiber connector of the pair of combo-port interfaces is active. The value 'copper' means the interface with copper connector of the pair is active. The value 'na' means not supported. |
| hpnicfifComboPortEntry | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.4.1 | not-accessible | The entry of hpnicfifComboPortTable. | |
| NUM hpnicfifComboPortIndex | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.4.1.1 | InterfaceIndex | read-only | The combo-port interface index. Its value is the same as the value of ifIndex in ifTable, but only includes indexes of the combo-port interfaces. |
| hpnicfifComboPortTable | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.4 | not-accessible | Combo-port table. | |
| SPE hpnicfifEthernetAutoSpeed | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.20 | SpeedModeFlag | read-write | This object indicates which kinds of speed mode are negotiable on this port. Only when a bit of hpnicfifEthernetAutoSpeedMask is '1', the corresponding bit of this object can be set to '1', indicating the corresponding speed mode is negotiable. For example, if the value of hpnicfifEthernetAutoSpeedMask is 0xA0, which indicates speed mode 's10M' and 's1000M' are negotiable, the possible value of this object should be one of the four values (0x00, 0x20, 0x80 and 0xA0). If the value of hpnicfifEthernetSpeed is not 'auto', the value of this object is insignificant and should be ignored. The value length of this object should be as long as that of hpnicfifEthernetAutoSpeedMask. |
| SPE hpnicfifEthernetAutoSpeedMask | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.19 | SpeedModeFlag | read-only | This object specifies which kinds of speed mode can be negotiated. Each bit corresponds to a kind of speed mode. If the value of a bit is '1', it means the corresponding speed mode is negotiable on the port. Otherwise the negotiation for that kind of speed mode is not supported on this port. If there are several negotiable speed modes, all bits for them are '1'. For example, if the speed mode 's10M' and 's1000M' can be negotiable, the value of this object is 0xA0. |
| INT hpnicfifEthernetDuplex | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.3 | INTEGER | read-write | Ethernet interface mode. |
| INT hpnicfifEthernetFlowInterval | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.12 | INTEGER | read-write | Set flow interval of the ethernet. The NMS should set value to integer which is a multiple of 5. |
| OCT hpnicfifEthernetIsolate | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.13 | OCTET STRING | read-write | Isolate group means that all ports in the same isolate group can not send and receive packets each other. Each octet within this value specifies a set of eight isolate groups, with the first octet specifying isolate groups 1 through 8, the second octet specifying isolate groups 9 through 16, etc. Within each octet, the leftmost bit is the first bit. the first bit represents the lowest numbered isolate group, and the last bit represents the highest numbered isolate group. one port can belong to more than one isolate group. Thus, each isolate group is represented by a single bit within the value of this object. If that bit has a value of '1', then that isolate group includes this port; the port is not included if its bit has a value of '0'. for example, the first octet is '10000100' means that the port is included in the isolate group 1 and isolate group 6. |
| INT hpnicfifEthernetMdi | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.7 | INTEGER | read-write | Type of the line connected to the port. MDI-II (straight-through cable): 1 MDI-X (crossover cable): 2 MDI-AUTO (auto-sensing): 3 |
| INT hpnicfifEthernetMTU | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.4 | INTEGER | read-write | MTU on the Ethernet interface. |
| INT hpnicfifEthernetSpeed | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.5 | INTEGER | read-write | Ethernet interface speed. |
| INT hpnicfifEthernetTest | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.10 | INTEGER | read-write | Test this interface. The actual testing will be different according to products. Read operation not supported. |
| T/F hpnicfifFlowControl | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.7 | TruthValue | read-write | Flow control status. |
| hpnicfifHybridPortEntry | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.3.1 | not-accessible | Hybrid-port configuration table. | |
| INT hpnicfifHybridPortIndex | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.3.1.1 | INTEGER | read-only | Index number of Hybrid-port. |
| hpnicfifHybridPortTable | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.3 | not-accessible | Hybrid-port configuration table. | |
| OCT hpnicfifHybridTaggedVlanListHigh | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.3.1.3 | OCTET STRING | read-write | Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each tagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is tagged in the set of VLANs; the VLAN is not tagged if its bit has a value of '0'. |
| OCT hpnicfifHybridTaggedVlanListLow | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.3.1.2 | OCTET STRING | read-write | Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each tagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is tagged in the set of VLANs; the VLAN is not tagged if its bit has a value of '0'. |
| OCT hpnicfifHybridUnTaggedVlanListHigh | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.3.1.5 | OCTET STRING | read-write | Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each untagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is untagged in the set of VLANs; the VLAN is not untagged if its bit has a value of '0'. |
| OCT hpnicfifHybridUnTaggedVlanListLow | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.3.1.4 | OCTET STRING | read-write | Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each untagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is untagged in the set of VLANs; the VLAN is not untagged if its bit has a value of '0'. |
| I32 hpnicfifInErrorPktsRate | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.37 | Integer32 | read-only | The rate of inbound error packets on the interface. |
| C64 hpnicfifInNormalPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.39 | Counter64 | read-only | The number of normal packets received on the interface. |
| C64 hpnicfifInPayloadOctets | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.36 | Counter64 | read-only | The actual input octets of the interface. |
| C64 hpnicfifInPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.38 | Counter64 | read-only | The number of packets received on the interface. |
| C64 hpnicfifIPv4InBroadcastPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.4 | Counter64 | read-only | Number of broadcast packets based on IPv4 received on the interface. |
| C64 hpnicfifIPv4InDiscards | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.5 | Counter64 | read-only | Number of discard packets based on IPv4 received on the interface. |
| C64 hpnicfifIPv4InErrors | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.6 | Counter64 | read-only | Number of error packets based on IPv4 received on the interface. |
| C64 hpnicfifIPv4InMultiPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.3 | Counter64 | read-only | Number of multicast packets based on IPv4 received on the interface. |
| C64 hpnicfifIPv4InOctets | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.1 | Counter64 | read-only | Number of octets based on IPv4 received on the interface. |
| C64 hpnicfifIPv4InUcastPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.2 | Counter64 | read-only | Number of unicast packets based on IPv4 received on the interface. |
| C64 hpnicfifIPv4OutBroadcastPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.10 | Counter64 | read-only | Number of broadcast packets based on IPv4 transmitted out of the interface. |
| C64 hpnicfifIPv4OutDiscards | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.11 | Counter64 | read-only | Number of discard packets based on IPv4 transmitted out of the interface. |
| C64 hpnicfifIPv4OutErrors | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.12 | Counter64 | read-only | Number of error packets based on IPv4 transmitted out of the interface. |
| C64 hpnicfifIPv4OutMultiPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.9 | Counter64 | read-only | Number of multicast packets based on IPv4 transmitted out of the interface. |
| C64 hpnicfifIPv4OutOctets | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.7 | Counter64 | read-only | Number of octets based on IPv4 transmitted out of the interface. |
| C64 hpnicfifIPv4OutUcastPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.8 | Counter64 | read-only | Number of unicast packets based on IPv4 transmitted out of the interface. |
| C64 hpnicfifIPv6InAnycastPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.16 | Counter64 | read-only | Number of anycast packets based on IPv6 received on the interface. |
| C64 hpnicfifIPv6InDiscards | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.17 | Counter64 | read-only | Number of discard packets based on IPv6 received on the interface. |
| C64 hpnicfifIPv6InErrors | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.18 | Counter64 | read-only | Number of error packets based on IPv6 received on the interface. |
| C64 hpnicfifIPv6InMultiPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.15 | Counter64 | read-only | Number of multicast packets based on IPv6 received on the interface. |
| C64 hpnicfifIPv6InOctets | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.13 | Counter64 | read-only | Number of octets based on IPv6 received on the interface. |
| C64 hpnicfifIPv6InUcastPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.14 | Counter64 | read-only | Number of unicast packets based on IPv6 received on the interface. |
| C64 hpnicfifIPv6OutAnycastPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.22 | Counter64 | read-only | Number of anycast packets based on IPv6 transmitted out of the interface. |
| C64 hpnicfifIPv6OutDiscards | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.23 | Counter64 | read-only | Number of discard packets based on IPv6 transmitted out of the interface. |
| C64 hpnicfifIPv6OutErrors | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.24 | Counter64 | read-only | Number of error packets based on IPv6 transmitted out of the interface. |
| C64 hpnicfifIPv6OutMultiPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.21 | Counter64 | read-only | Number of multicast packets based on IPv6 transmitted out of the interface. |
| C64 hpnicfifIPv6OutOctets | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.19 | Counter64 | read-only | Number of octets based on IPv6 transmitted of the interface. |
| C64 hpnicfifIPv6OutUcastPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1.20 | Counter64 | read-only | Number of unicast packets based on IPv6 transmitted out of the interface. |
| I32 hpnicfifIsolateGroupID | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.17 | Integer32 | read-write | Isolate group identifier. Value zero means this interface does not belong to any isolate group. |
| T/F hpnicfifISPhyPort | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.2 | TruthValue | read-only | Whether it is a physical interface. |
| INT hpnicfifisUplinkPort | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.18 | INTEGER | read-only | Ethernet uplink status, default value is 2. |
| INT hpnicfifMacAddressLearn | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.9 | INTEGER | read-only | This object indicates if the interface is allowed to learn mac address. eanbled(1) means the interface can learn mac address, otherwise disabled(2) can be set. |
| INT hpnicfifMacAddrLearnMode | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.11 | INTEGER | read-only | Status indicates mac address learn mode of the interface. IVL(1) means independent VLAN learning. SVL means shared VLAN learning. |
| INT hpnicfifMcastControl | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.6 | INTEGER | read-write | Broadcast storm suppression with the step length of 1, ranging from 0 to 100 percent. In some products the step is 5, ranging from 0 to 100. |
| T/F hpnicfifMirrorPort | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.4 | TruthValue | read-write | Whether it is a mirror port. |
| I32 hpnicfifMulSuppression | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.20 | Integer32 | read-write | The multicast suppression with ranging from 0 to 100 percent in ratio mode. The step is determined by hpnicfifMulSuppressionStep. |
| I32 hpnicfifMulSuppressionStep | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.16 | Integer32 | read-only | The step of multicast suppression in ratio mode. |
| C64 hpnicfifOutPayloadOctetsEx | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.35 | Counter64 | read-only | The actual output octets of the interface. |
| C64 hpnicfifOutPkts | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.40 | Counter64 | read-only | The number of packets sent on the interface. |
| hpnicfifPktBufEntry | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.5.1 | not-accessible | The entry of hpnicfifPktBufTable. | |
| I32 hpnicfifPktBufFree | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.5.1.1 | Integer32 | read-only | The number of packet buffers available for the interface. |
| I32 hpnicfifPktBufInit | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.5.1.2 | Integer32 | read-only | The number of packet buffers allocated when the interface was created. |
| I32 hpnicfifPktBufMin | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.5.1.3 | Integer32 | read-only | The smallest number of packet buffers available for the interface. |
| C64 hpnicfifPktBufMiss | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.5.1.4 | Counter64 | read-only | The number of times that the interface failed to obtain a packet buffer. Failure to obtain a buffer indicates that buffers were busy. |
| hpnicfifPktBufTable | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.5 | not-accessible | Packet buffer table. | |
| hpnicfifPortProtocolStatEntry | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13.1 | not-accessible | The entry of hpnicfifPortProtocolStatTable. | |
| hpnicfifPortProtocolStatTable | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.13 | not-accessible | This table contains objects of port statistics information based on IPv4 and IPv6 protocols. | |
| INT hpnicfifPpsBcastDisValControl | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.13 | INTEGER | read-write | Control the port's pps(packet per second) broadcast suppression. When the port is enabled, its pps broadcast suppression value is the global disperse value, and when disabled, it doesn't suppress broadcast. |
| I32 hpnicfifPpsMcastControl | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.12 | Integer32 | read-write | The broadcast suppression with pps(packet per second) type. The max value is determined by the port type and product. |
| I32 hpnicfifPpsMulSuppression | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.21 | Integer32 | read-write | The multicast suppression in pps(packet per second) mode. The max pps value is determined by hpnicfifPpsMulSuppressionMax. |
| I32 hpnicfifPpsMulSuppressionMax | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.17 | Integer32 | read-only | The max pps(packet per second) value of multicast suppression in pps mode. |
| I32 hpnicfifPpsUniSuppression | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.19 | Integer32 | read-write | The unicast suppression in pps(packet per second) mode. The max value is determined by hpnicfifPpsUniSuppressionMax. |
| I32 hpnicfifPpsUniSuppressionMax | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.15 | Integer32 | read-only | The max pps(packet per second) value of unicast suppression in pps mode. |
| T/F hpnicfifSrcMacControl | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.8 | TruthValue | read-only | Whether to filter by source MAC address. |
| T/F hpnicfifUnBoundPort | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.1 | TruthValue | read-only | Whether it is the unbound port. (true indicates that the port is the main port of the aggregation or the port does not participate in the aggregation.) |
| I32 hpnicfifUniSuppression | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.18 | Integer32 | read-write | The unicast suppression with the ranging from 0 to 100 percent in ratio mode. The step is determined by hpnicfifUniSuppressionStep. |
| I32 hpnicfifUniSuppressionStep | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.14 | Integer32 | read-only | The step of unicast suppression in ratio mode. |
| DRO hpnicfifUnknownPacketDropMul | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.28 | DropDirection | read-write | Control the port's unknown-multicast packets drop. When inbound direction is enabled on this port, the port will drop unknown-multicast packets in inbound direction. When outbound direction is enabled on this port, the port will drop unknown-multicast packets in outbound direction. When both directions are enabled on this port, the port will drop unknown-multicast packets in both inbound and outbound directions. |
| DRO hpnicfifUnknownPacketDropUni | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.29 | DropDirection | read-write | Control the port's unknown-unicast packets drop. When inbound direction is enabled on this port, the port will drop unknown-unicast packets in inbound direction. When outbound direction is enabled on this port, the port will drop unknown-unicast packets in outbound direction. When both directions are enabled on this port, the port will drop unknown-unicast packets in both inbound and outbound directions. |
| OCT hpnicfifVLANTrunkAllowListHigh | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.3.1.7 | OCTET STRING | read-write | Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is allowed in the set of VLANs; the VLAN is not allowed if its bit has a value of '0'. |
| OCT hpnicfifVLANTrunkAllowListLow | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.3.1.6 | OCTET STRING | read-write | Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each allowed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is allowed in the set of VLANs; the VLAN is not allowed if its bit has a value of '0'. |
| INT hpnicfifVLANTrunkGvrpRegistration | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.3.1.2 | INTEGER | read-write | GVRP registration information normal: This is the default configuration. Allow create, register and unregister vlans dynamiclly at this port. fixed: Aallow create and register vlan manually at this port. Prevent from unregistering vlans or registering known vlans of this port at another trunk port. forbidden: Unregister all vlans but vlan 1, forbid to create or register any other vlans at this port. |
| NUM hpnicfifVLANTrunkIndex | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.3.1.1 | InterfaceIndex | read-only | Index number of the VLANTrunk interface. |
| OCT hpnicfifVLANTrunkPassListHigh | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.3.1.5 | OCTET STRING | read-only | Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 2049 through 2056, the second octet specifying VLANs 2057 through 2064, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each actually passed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is actually passed in the set of VLANs; the VLAN is not actually passed if its bit has a value of '0'. |
| OCT hpnicfifVLANTrunkPassListLow | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.3.1.4 | OCTET STRING | read-only | Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each actually passed VLAN of the trunk port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is actually passed in the set of VLANs; the VLAN is not actually passed if its bit has a value of '0'. |
| hpnicfifVLANTrunkStatusEntry | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.3.1 | not-accessible | Gvrp attributes on the VlanTrunk port. | |
| hpnicfifVLANTrunkStatusTable | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.3 | not-accessible | Gvrp attributes on the VlanTrunk port. | |
| INT hpnicfifVLANType | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.5 | INTEGER | read-write | port vlan types. hybrid (3) port can carry multiple VLANs. If fabric function is supported, fabric(4) means the port is a fabric port. |
| INT hpnicfifVlanVPNStatus | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.14 | INTEGER | read-write | Vlan VPN enable status. |
| I32 hpnicfifVlanVPNTPID | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.16 | Integer32 | read-write | Port based Vlan VPN TPID(Tag Protocol Indentifier), default value is 0x8100. Please refer to hpnicfVlanVPNTPIDMode to get more information. |
| INT hpnicfifVlanVPNUplinkStatus | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.15 | INTEGER | read-write | Vlan VPN uplink status. |
| INT hpnicfifXXBasePortIndex | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.10 | INTEGER | read-only | Index number of the port and the first port index of the device is 1. |
| INT hpnicfifXXDevPortIndex | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1.11 | INTEGER | read-only | Device index of the port. |
| hpnicfifXXEntry | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1.1 | not-accessible | Entries of extended interface information table. | |
| hpnicfifXXTable | 1.3.6.1.4.1.11.2.14.11.15.8.35.1.1 | not-accessible | Extended interface information table. | |
| I32 hpnicfIsolateGroupMax | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.5 | Integer32 | read-only | Max isolate group that this device support, the value is zero means that the device does not support isolate group. |
| hpnicfLswExtInterface | 1.3.6.1.4.1.11.2.14.11.15.8.35.1 | |||
| hpnicfLswL2InfMib | 1.3.6.1.4.1.11.2.14.11.15.8.35.5 | |||
| hpnicfLswL2InfMibObject | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1 | |||
| INT hpnicfMaxMacLearn | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.4.1.8 | INTEGER | read-write | The maximum number of MAC addresses that the port can learn. The value -1 means that the number of Mac addresses that the port can learn is unlimited. |
| I32 hpnicfMaxMacLearnRange | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.12 | Integer32 | read-only | The maximum number of MAC address that the port supports. |
| STR hpnicfPortIsolateGroupDescription | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.11.1.4 | DisplayString | read-create | Port isolate group description, default value is zero-length string. |
| hpnicfPortIsolateGroupEntry | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.11.1 | not-accessible | The entry of hpnicfPortIsolateGroupTable. | |
| I32 hpnicfPortIsolateGroupIndex | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.11.1.1 | Integer32 | not-accessible | Port isolate group identifier. The index of the hpnicfPortIsolateGroupTable. The value ranges from 1 to the limit of isolate group quantity. |
| ROW hpnicfPortIsolateGroupRowStatus | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.11.1.3 | RowStatus | read-create | Current operation status of the row. |
| hpnicfPortIsolateGroupTable | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.11 | not-accessible | Isolate Group attribute table. | |
| NUM hpnicfPortIsolateUplinkIfIndex | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.11.1.2 | InterfaceIndex | read-create | Index number of the uplink interface. |
| INT hpnicfSlotPortMax | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.1 | INTEGER | read-only | Max ports of the slots. |
| INT hpnicfSwitchPortMax | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.2 | INTEGER | read-only | Max ports that this switch includes. |
| I32 hpnicfVlanVPNTPID | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.10 | Integer32 | read-write | Global Vlan VPN TPID(Tag Protocol Indentifier), default value is 0x8100. |
| INT hpnicfVlanVPNTPIDMode | 1.3.6.1.4.1.11.2.14.11.15.8.35.5.1.9 | INTEGER | read-only | Vlan VPN TPID mode. The value 'port-based' means VLAN VPN TPID value would be set based on port via hpnicfifVlanVPNTPID. In this situation, hpnicfVlanVPNTPID is meaningless and always return 0x8100. The value 'global' means VLAN VPN TPID value should be set globally via hpnicfVlanVPNTPID. In this situation, hpnicfifVlanVPNTPID in hpnicfethernetTable has the same value with hpnicfVlanVPNTPID. |
RFC description
Manages Layer 2 switch interface (port) configuration including speed, duplex, and flow control on HP/Comware switches.
Start monitoring HP/H3C Comware-based ICF switch (Layer 2 port attributes/storm suppression) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.