All MIBs › HP-SN-BGP4-GROUP-MIB
Category: Protocol: BGP, Routing Protocols, Technology: Routing/L3, Vendor: HP/HPE
Description: HP ServerNet (Foundry-heritage) SNMP MIB for BGP4 routing protocol configuration and neighbor management on HP SN routers.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HP-SN-BGP4-GROUP-MIB?
HP-SN-BGP4-GROUP-MIB is an SNMP MIB inherited from HP's ServerNet networking line (originally Foundry Networks technology acquired by HP), used to configure BGP4 (Border Gateway Protocol version 4) routing policy on HP SN routers and switches. It exposes configuration objects for BGP address filters and route aggregation, controlling which routes are permitted, denied, or aggregated in the router's BGP routing table. As a routing-policy configuration MIB, its relevance to device status monitoring is mainly about confirming the software/protocol configuration is correctly applied, such as verifying an address filter's rowStatus is active, rather than reporting hardware sensor data. It complements the standard BGP4-MIB (RFC 4273), which would carry the actual peer/session operational state, while this module adds HP/Foundry-specific filtering and aggregation policy objects. It is typically deployed on HP SN core/edge routers running BGP in service-provider or large enterprise WAN environments. Engineers can download the HP-SN-BGP4-GROUP-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HP-SN-BGP4-GROUP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HP ProCurve Routing Switch 9304m/9308m/9315m (OEM'd Foundry Networks BigIron core routing switches)
Monitoring Examples
The module exposes snBgp4AddrFilterTable/Entry keyed by snBgp4AddrFilterIndex, holding snBgp4AddrFilterAction, snBgp4AddrFilterSourceIp/Mask, and snBgp4AddrFilterDestIp/Mask, alongside snBgp4AggregateAddrTable/Entry holding snBgp4AggregateAddrIp for route aggregation policy. An administrator would poll snBgp4AddrFilterRowStatus across configured filters to confirm a recently added filter is active and applying as expected, and check the aggregate address table to verify route summarization matches the intended CIDR block. Because this MIB is policy-configuration focused, actual BGP session/peer health would be monitored via the standard BGP4-MIB rather than this module.
What Can Be Monitored
- BGP address filter configuration and status
- filter action (permit/deny) per rule
- route aggregation address configuration
This MIB depends on
Related MIBs
Imported Objects
From HP-SN-ROOT-MIB
| snBgp4 | OBJECT-IDENTITY |
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| snBgp4Gen | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1 | |||
| INT snBgp4GenAlwaysCompareMed | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.1 | INTEGER | read-write | To enable/disable the comparison of the Multi-Exit Discriminator for paths from neighbors in different AS. |
| INT snBgp4GenAutoSummary | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.2 | INTEGER | read-write | To enable/disable the default behavior of automatic summarization of subnet routes into network-level routes. |
| INT snBgp4GenDefaultLocalPreference | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.3 | INTEGER | read-write | To set the default local preference attribute. |
| INT snBgp4GenDefaultInfoOriginate | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.4 | INTEGER | read-write | To enable/disable the default Information Originate. |
| INT snBgp4GenFastExternalFallover | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.5 | INTEGER | read-write | To enable/disable an action of immediately reset the BGP sessions of any directly adjacent external neighbors if the link used to reach them goes down. |
| INT snBgp4GenNextBootNeighbors | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.6 | INTEGER | read-write | The next-boot configured number of neighbors in a BGP Peer Group. The minimum value of this MIB is snBgp4GenMinNeighbors. The maximum value of this MIB is snBgp4GenMaxNeighbors. |
| INT snBgp4GenNextBootRoutes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.7 | INTEGER | read-write | The next-boot configured number of Routes. The minimum value of this MIB is snBgp4GenMinRoutes. The maximum value of this MIB is snBgp4GenMaxRoutes. |
| INT snBgp4GenSynchronization | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.8 | INTEGER | read-write | To enable/disable the synchronization between BGP and your IGP. |
| INT snBgp4GenKeepAliveTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.9 | INTEGER | read-write | The Keep alive timer. |
| INT snBgp4GenHoldTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.10 | INTEGER | read-write | The Hold time timer. |
| IP snBgp4GenRouterId | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.11 | IpAddress | read-write | BGP Router Id. |
| OCT snBgp4GenTableMap | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.12 | OCTET STRING | read-write | An octet string of the route-map name, each character of the name is represented by one octet. |
| INT snBgp4GenAdminStat | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.13 | INTEGER | read-write | The administrative status of BGP4 in the router. The value 'enabled' denotes that the BGP4 routing is active in this router; 'disabled' disables BGP4 routing on this router. |
| INT snBgp4GenDefaultMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.14 | INTEGER | read-write | To set default metric values for the BGP4 protocol. |
| INT snBgp4GenMaxNeighbors | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.15 | INTEGER | read-only | The maximum number of neighbors can be configured in a BGP Peer Group. |
| INT snBgp4GenMinNeighbors | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.16 | INTEGER | read-only | The minimum number of neighbors can be configured in a BGP Peer Group. |
| INT snBgp4GenMaxRoutes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.17 | INTEGER | read-only | The maximum configured number of Routes. |
| INT snBgp4GenMinRoutes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.18 | INTEGER | read-only | The minimum configured number of Routes. |
| INT snBgp4GenMaxAddrFilters | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.19 | INTEGER | read-only | The maximum configured number of BGP4 address filters. |
| INT snBgp4GenMaxAggregateAddresses | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.20 | INTEGER | read-only | The maximum configured number of BGP4 aggregate addresses. |
| INT snBgp4GenMaxAsPathFilters | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.21 | INTEGER | read-only | The maximum configured number of BGP4 AS-PATH filters. |
| INT snBgp4GenMaxCommunityFilters | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.22 | INTEGER | read-only | The maximum configured number of BGP4 Community filters. |
| INT snBgp4GenMaxNetworks | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.23 | INTEGER | read-only | The maximum configured number of BGP4 Networks. |
| INT snBgp4GenMaxRouteMapFilters | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.24 | INTEGER | read-only | The maximum configured number of BGP4 Route-map Filters. |
| INT snBgp4GenNeighPrefixMinValue | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.25 | INTEGER | read-only | The minimum configured value of BGP4 Neighbor Prefix. |
| INT snBgp4GenOperNeighbors | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.26 | INTEGER | read-only | The current operational max number of neighbors configured for a BGP Group. |
| INT snBgp4GenOperRoutes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.27 | INTEGER | read-only | The current operational number of Routes. |
| INT snBgp4GenLocalAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.28 | INTEGER | read-write | Bgp4 local autonomous system number. |
| INT snBgp4GenRoutesInstalled | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.29 | INTEGER | read-only | Bgp4 installed routes. |
| INT snBgp4GenAsPathInstalled | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.30 | INTEGER | read-only | Bgp4 installed autonomous system path. |
| INT snBgp4ExternalDistance | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.31 | INTEGER | read-write | Administrative distance for BGP external routes. |
| INT snBgp4InternalDistance | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.32 | INTEGER | read-write | Administrative distance for BGP internal routes. |
| INT snBgp4LocalDistance | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.33 | INTEGER | read-write | Administrative distance for BGP local routes. |
| INT snBgp4OperNumOfAttributes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.34 | INTEGER | read-only | The operational number of attribute entries. |
| INT snBgp4NextBootMaxAttributes | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.35 | INTEGER | read-write | The next boot maximum attribute entries. 10000 means reset to default. |
| INT snBgp4ClusterId | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.36 | INTEGER | read-write | A cluster ID which is represented by 4 bytes unsigned integer (0..0xFFFFFFFF). 0 means reset to default. |
| INT snBgp4ClientToClientReflection | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.37 | INTEGER | read-write | To enable/disable the client to client reflection in BGP4. |
| INT snBgp4GenTotalNeighbors | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.38 | INTEGER | read-only | The current total number of neighbors running in a BGP Group. |
| INT snBgp4GenMaxPaths | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.39 | INTEGER | read-write | The maximum configured number of Paths. |
| INT snBgp4GenConfedId | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.40 | INTEGER | read-write | Bgp4 Confederation Id. |
| OCT snBgp4GenConfedPeers | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.41 | OCTET STRING | read-write | An AS number from 1 to 0xFFFF construct confederation peers. There are 50(max peers) of them. This integer number is represented by 2 OCTETs. |
| INT snBgp4GenDampening | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.42 | INTEGER | read-write | The dampening of BGP4 in the router. value 'none' denotes that the BGP4 dampening is off 'parameters' denotes parameters are confibrurable. 'routeMap' denotes routemap is configurable. |
| INT snBgp4GenDampenHalfLife | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.43 | INTEGER | read-write | Bgp4 Dampening Half Life. |
| INT snBgp4GenDampenReuse | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.44 | INTEGER | read-write | Bgp4 Dampening Reuse. |
| INT snBgp4GenDampenSuppress | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.45 | INTEGER | read-write | Bgp4 Dampening Suppress. |
| INT snBgp4GenDampenMaxSuppress | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.46 | INTEGER | read-write | Bgp4 Dampening Max Suppress Time. |
| OCT snBgp4GenDampenMap | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.1.47 | OCTET STRING | read-write | An octet string of the route-map name for dampening, each character of the name is represented by one octet. |
| snBgp4AddrFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2 | |||
| snBgp4AddrFilterTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1 | not-accessible | Bgp4 Address Filter table. | |
| snBgp4AddrFilterEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1 | not-accessible | An entry in the Bgp4 Address Filter table. | |
| INT snBgp4AddrFilterIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.1 | INTEGER | read-only | The table index for a filter entry. |
| INT snBgp4AddrFilterAction | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.2 | INTEGER | read-write | Action to take if the bgp address match with this filter. |
| IP snBgp4AddrFilterSourceIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.3 | IpAddress | read-write | Source IP address. |
| IP snBgp4AddrFilterSourceMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.4 | IpAddress | read-write | Source IP subnet mask. |
| IP snBgp4AddrFilterDestIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.5 | IpAddress | read-write | Destination IP address. |
| IP snBgp4AddrFilterDestMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.6 | IpAddress | read-write | Destination IP subnet mask. |
| INT snBgp4AddrFilterRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.2.1.1.7 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
| snBgp4AggregateAddr | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3 | |||
| snBgp4AggregateAddrTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1 | not-accessible | Bgp4 Aggregate Address table. | |
| snBgp4AggregateAddrEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1 | not-accessible | An entry in the Bgp4 Aggregate Address table. | |
| IP snBgp4AggregateAddrIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.1 | IpAddress | read-only | Aggregate Address IP address. |
| IP snBgp4AggregateAddrMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.2 | IpAddress | read-only | Aggregate Address IP subnet mask. |
| INT snBgp4AggregateAddrOption | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.3 | INTEGER | read-only | address(1), asSet(2), summaryOnly(3), the suppressMap(4), advertiseMap(5), attributeMap(6) are Options for creating an aggregate entry in a BGP routing table. |
| OCT snBgp4AggregateAddrMap | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.4 | OCTET STRING | read-write | This object associates with the snBgp4AggregateAddrOption and the suppressMap(4), advertiseMap(5), attributeMap(6) of the snBgp4AggregateAddrOption are only two Options for creating an aggregate address map. A SNMP-SET error will be returned for other options. An octet string of the map name, each character of the name is represented by one octet. |
| INT snBgp4AggregateAddrRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.3.1.1.5 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
| snBgp4AsPathFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4 | |||
| snBgp4AsPathFilterTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1 | not-accessible | Bgp4 AS-Path Filter table. | |
| snBgp4AsPathFilterEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1 | not-accessible | An entry in the Bgp4 As-path Filter table. | |
| INT snBgp4AsPathFilterIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.1 | INTEGER | read-only | The table index for a filter entry. |
| INT snBgp4AsPathFilterAction | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.2 | INTEGER | read-write | Action to take if the bgp address match with this filter. |
| OCT snBgp4AsPathFilterRegExpression | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.3 | OCTET STRING | read-write | Autonomous system in the filter using a regular expression. Each character of the regular expression string is represented by one octet. |
| INT snBgp4AsPathFilterRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.4.1.1.4 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
| snBgp4CommunityFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5 | |||
| snBgp4CommunityFilterTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1 | not-accessible | Bgp4 Community Filter table. | |
| snBgp4CommunityFilterEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1 | not-accessible | An entry in the Bgp4 Community Filter table. | |
| INT snBgp4CommunityFilterIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.1 | INTEGER | read-only | The table index for a filter entry. |
| INT snBgp4CommunityFilterAction | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.2 | INTEGER | read-write | Action to take if the bgp address match with this filter. |
| OCT snBgp4CommunityFilterCommNum | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.3 | OCTET STRING | read-write | A number from 1 to 0xFFFFFFFF. There are 20 of them. This integer number is represented by 4 OCTETs. |
| INT snBgp4CommunityFilterInternet | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.4 | INTEGER | read-write | Disabled/Enabled the Internet Community. |
| INT snBgp4CommunityFilterNoAdvertise | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.5 | INTEGER | read-write | Do not advertise this route to any peer (internal or external). |
| INT snBgp4CommunityFilterNoExport | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.6 | INTEGER | read-write | Do not advertise this route to an EBGP peer. |
| INT snBgp4CommunityFilterRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.7 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
| INT snBgp4CommunityFilterLocalAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.5.1.1.8 | INTEGER | read-write | Send this route to peers in other sub-autonomous systems within the local confederation. Do not advertise this route to an external system. |
| snBgp4NeighGenCfg | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6 | |||
| snBgp4NeighGenCfgTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1 | not-accessible | Bgp4 Neighbor General Configuration table. | |
| snBgp4NeighGenCfgEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1 | not-accessible | An entry in the Bgp4 Community Filter table. | |
| IP snBgp4NeighGenCfgNeighIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.1 | IpAddress | read-only | The IP Address for a neighbor entry. |
| INT snBgp4NeighGenCfgAdvertlevel | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.2 | INTEGER | read-write | To set the minimum interval between the sending of BGP routing updates. |
| INT snBgp4NeighGenCfgDefOriginate | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.3 | INTEGER | read-write | To enable/disable the default originate for this neighbor. |
| INT snBgp4NeighGenCfgEbgpMultihop | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.4 | INTEGER | read-write | To enable/disable the EBGP Muitihop for this neighbor. |
| INT snBgp4NeighGenCfgMaxPrefix | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.5 | INTEGER | read-write | To control how many prefixes can be received from a neighbor. The minimum value of the maximum prefix is snBgp4GenNeighPrefixMinValue. The maximum value of the maximum prefix is snBgp4GenOperRoutes. |
| INT snBgp4NeighGenCfgNextHopSelf | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.6 | INTEGER | read-write | To enable/disable the next-hop processing of BGP updates on the router. |
| INT snBgp4NeighGenCfgRemoteAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.7 | INTEGER | read-write | To specify a neighbor with an autonomous system number(AS). |
| INT snBgp4NeighGenCfgSendComm | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.8 | INTEGER | read-write | To specify that a COMMUNITES attribute should be sent to a BGP neighbor. |
| INT snBgp4NeighGenCfgWeight | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.9 | INTEGER | read-write | To assign a weight to a neighbor connection. |
| OCT snBgp4NeighGenCfgWeightFilterList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.10 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 16 of them. This integer number is represented by 2 OCTETs. |
| INT snBgp4NeighGenCfgRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.11 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row applyDefault(6)...apply default value to an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
| INT snBgp4NeighGenCfgUpdateSrcLpbIntf | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.12 | INTEGER | read-write | To allow internal BGP sessions to use any operational loopback interface (1..8) for TCP connections. Zero interface means to restore the interface assignment to the closest interface, which is called the best local address. |
| INT snBgp4NeighGenCfgRouteRefClient | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.13 | INTEGER | read-write | To configure the router as a BGP route reflector, enable the specified neighbor as its client. When all the clients are disabled, the local router is no longer a route reflector. |
| INT snBgp4NeighGenCfgRemovePrivateAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.14 | INTEGER | read-write | To enable/disable filtering private AS number. |
| INT snBgp4NeighGenCfgEbgpMultihopTtl | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.15 | INTEGER | read-write | The EBGP Muitihop TTL for this neighbor. |
| INT snBgp4NeighGenCfgShutdown | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.16 | INTEGER | read-write | To enable/disable BGP4 Nbr Shutdown. |
| INT snBgp4NeighGenCfgKeepAliveTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.17 | INTEGER | read-write | The Keep alive timer. |
| INT snBgp4NeighGenCfgHoldTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.18 | INTEGER | read-write | The Hold time timer. |
| OCT snBgp4NeighGenCfgDefOrigMap | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.19 | OCTET STRING | read-write | An octet string of the route-map name, each character of the name is represented by one octet. |
| OCT snBgp4NeighGenCfgDesc | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.20 | OCTET STRING | read-write | An octet string of the neighbor description. |
| OCT snBgp4NeighGenCfgPass | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.6.1.1.21 | OCTET STRING | read-write | An octet string of the neighbor Md5 password. |
| snBgp4NeighDistGroup | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7 | |||
| snBgp4NeighDistGroupTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1 | not-accessible | Bgp4 Neighbor Distribute Group table. | |
| snBgp4NeighDistGroupEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1 | not-accessible | An entry in the Bgp4 Distribute Group table. | |
| IP snBgp4NeighDistGroupNeighIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.1 | IpAddress | read-only | The IP Address for a neighbor entry. |
| INT snBgp4NeighDistGroupDir | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.2 | INTEGER | read-only | The incoming/outgoing advertisements to which the access list is applied. |
| OCT snBgp4NeighDistGroupAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.3 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 16 of them. This integer number is represented by 2 OCTETs. |
| INT snBgp4NeighDistGroupRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.4 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
| OCT snBgp4NeighDistGroupInFilterList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.5 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 16 of them. This integer number is represented by 2 OCTETs. |
| OCT snBgp4NeighDistGroupOutFilterList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.6 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 16 of them. This integer number is represented by 2 OCTETs. |
| OCT snBgp4NeighDistGroupInIpAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.7 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 1 of them. This integer number is represented by 2 OCTETs. |
| OCT snBgp4NeighDistGroupOutIpAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.8 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 1 of them. This integer number is represented by 2 OCTETs. |
| OCT snBgp4NeighDistGroupInPrefixList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.9 | OCTET STRING | read-write | A Prefix name list. |
| OCT snBgp4NeighDistGroupOutPrefixList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.7.1.1.10 | OCTET STRING | read-write | A Prefix name list. |
| snBgp4NeighFilterGroup | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8 | |||
| snBgp4NeighFilterGroupTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1 | not-accessible | Bgp4 Neighbor Filter Group table. | |
| snBgp4NeighFilterGroupEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1 | not-accessible | An entry in the Bgp4 Neighbor Filter Group table. | |
| IP snBgp4NeighFilterGroupNeighIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.1 | IpAddress | read-only | The IP Address for a neighbor entry. |
| INT snBgp4NeighFilterGroupDir | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.2 | INTEGER | read-only | The incoming/outgoing advertisements to which the access list is applied. |
| OCT snBgp4NeighFilterGroupAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.3 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 16 of them. This integer number is represented by 2 OCTETs. |
| INT snBgp4NeighFilterGroupRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.4 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
| OCT snBgp4NeighFilterGroupInFilterList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.5 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 16 of them. This integer number is represented by 2 OCTETs. |
| OCT snBgp4NeighFilterGroupOutFilterList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.6 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 16 of them. This integer number is represented by 2 OCTETs. |
| OCT snBgp4NeighFilterGroupInAsPathAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.7 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 1 of them. This integer number is represented by 2 OCTETs. |
| OCT snBgp4NeighFilterGroupOutAsPathAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.8 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 1 of them. This integer number is represented by 2 OCTETs. |
| INT snBgp4NeighFilterGroupWeight | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.9 | INTEGER | read-write | To assign a weight to a neighbor filter. |
| OCT snBgp4NeighFilterGroupWeightAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.8.1.1.10 | OCTET STRING | read-write | A number from 1 to 0xFFFF. There are 1 of them. This integer number is represented by 2 OCTETs. |
| snBgp4NeighRouteMap | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9 | |||
| snBgp4NeighRouteMapTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1 | not-accessible | Bgp4 Neighbor Route Map table. | |
| snBgp4NeighRouteMapEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1 | not-accessible | An entry in the Bgp4 Route Map table. | |
| IP snBgp4NeighRouteMapNeighIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.1 | IpAddress | read-only | The IP Address for a neighbor entry. |
| INT snBgp4NeighRouteMapDir | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.2 | INTEGER | read-only | The incoming/outgoing advertisements to which the access list is applied. |
| OCT snBgp4NeighRouteMapMapName | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.3 | OCTET STRING | read-write | An octet string of the route-map name, Each character of the name is represented by one octet. |
| INT snBgp4NeighRouteMapRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.9.1.1.4 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
| snBgp4Network | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10 | |||
| snBgp4NetworkTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1 | not-accessible | Bgp4 Network Weight table. | |
| snBgp4NetworkEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1 | not-accessible | An entry in the Bgp4 Network Weight table. | |
| IP snBgp4NetworkIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.1 | IpAddress | read-only | The IP Address for a network entry. |
| IP snBgp4NetworkSubnetMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.2 | IpAddress | read-only | The subnet mask for a network entry. |
| INT snBgp4NetworkWeight | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.3 | INTEGER | read-write | To assign a weight to a neighbor connection. |
| INT snBgp4NetworkBackdoor | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.4 | INTEGER | read-write | To enable/disable the backdoor for this network. |
| INT snBgp4NetworkRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.10.1.1.5 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
| snBgp4Redis | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11 | |||
| snBgp4RedisTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1 | not-accessible | The BGP4 Redistribution contains configurations that could be imported into the BGP4 domain. | |
| snBgp4RedisEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1 | not-accessible | The BGP4 Redistribution Entry specifies a particular RIP or , OSPF, or Static route to be imported into the BGP4 domain. | |
| INT snBgp4RedisProtocol | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.1 | INTEGER | read-only | The imported configuration into BGP4 domain is set in the following: rip(1): - the RIP. ospf(2): - the OSPF. static(3): - the static. connected(4): - the connected. |
| INT snBgp4RedisMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.2 | INTEGER | read-write | The metric of using the specified protocol Metric value. |
| OCT snBgp4RedisRouteMap | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.3 | OCTET STRING | read-write | An octet string of the route-map name, each character of the name is represented by one octet. |
| INT snBgp4RedisWeight | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.4 | INTEGER | read-write | To assign a weight for the specified protocol. |
| INT snBgp4RedisMatchInternal | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.5 | INTEGER | read-write | This object is only applicable to the OSPF protocol. |
| INT snBgp4RedisMatchExternal1 | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.6 | INTEGER | read-write | This object is only applicable to the OSPF protocol. |
| INT snBgp4RedisMatchExternal2 | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.7 | INTEGER | read-write | This object is only applicable to the OSPF protocol. |
| INT snBgp4RedisRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.11.1.1.8 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
| snBgp4RouteMapFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12 | |||
| snBgp4RouteMapFilterTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1 | not-accessible | Bgp4 RouteMap Filter table. | |
| snBgp4RouteMapFilterEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1 | not-accessible | An entry in the Bgp4 RouteMap Filter table. | |
| OCT snBgp4RouteMapFilterMapName | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.1 | OCTET STRING | read-only | An octet string of the route-map name, each character of the name is represented by one octet. |
| INT snBgp4RouteMapFilterSequenceNum | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.2 | INTEGER | read-only | A sequence number for this particular route-map. |
| INT snBgp4RouteMapFilterAction | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.3 | INTEGER | read-write | Action to take if the bgp address match with this filter. |
| INT snBgp4RouteMapFilterRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.12.1.1.4 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
| snBgp4RouteMapMatch | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13 | |||
| snBgp4RouteMapMatchTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1 | not-accessible | Bgp4 Route Map Set table. | |
| snBgp4RouteMapMatchEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1 | not-accessible | An entry in the Bgp4 Route Map Match table. | |
| OCT snBgp4RouteMapMatchMapName | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.1 | OCTET STRING | read-only | An octet string of the route-map name, each character of the name is represented by one octet. |
| INT snBgp4RouteMapMatchSequenceNum | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.2 | INTEGER | read-only | A sequence number for this particular route-map. |
| OCT snBgp4RouteMapMatchAsPathFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.3 | OCTET STRING | read-write | A number from 1 to 0xFFFF and there are 10 of 2 OCTETs. This integer number is represented by 2 OCTETs. To match a BGP autonomous system path access list. |
| OCT snBgp4RouteMapMatchCommunityFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.4 | OCTET STRING | read-write | A number from 1 to 0xFFFF and there are 10 of 2 OCTETs. This integer number is represented by 2 OCTETs. To match a BGP community access list. |
| OCT snBgp4RouteMapMatchAddressFilter | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.5 | OCTET STRING | read-write | A number from 1 to 0xFFFF and there are 10 of 2 OCTETs. This integer number is represented by 2 OCTETs. To match a BGP address access list. |
| INT snBgp4RouteMapMatchMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.6 | INTEGER | read-write | To match a metric for BGP routes. |
| OCT snBgp4RouteMapMatchNextHopList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.7 | OCTET STRING | read-write | A number from 1 to 0xFFFF and there are 16 of 2 OCTETs. This integer number is represented by 2 OCTETs. To match a BGP next-hop access list. |
| INT snBgp4RouteMapMatchRouteType | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.8 | INTEGER | read-write | To match a route-type. Currently only externalType1(2), externalType2(3), internal(4) is supported for SNMP-SET. |
| OCT snBgp4RouteMapMatchTagList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.9 | OCTET STRING | read-write | To match a BGP tag access list. |
| INT snBgp4RouteMapMatchRowMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.10 | INTEGER | read-write | This object is used together with above MIBs in the same VARBIND to set and reset any MIBs in the table. The bit number is referred to the snBgp4RouteMapMatchEntry number of each row in the table. The bit is ON - means set, The bit is OFF - means reset |
| OCT snBgp4RouteMapMatchAsPathAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.11 | OCTET STRING | read-write | A number from 1 to 0xFFFFFFFF and there are 5 of 4 OCTETs. This integer number is represented by 4 OCTETs. To match a BGP autonomous system path access list. |
| OCT snBgp4RouteMapMatchCommunityList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.12 | OCTET STRING | read-write | A number from 1 to 0xFFFFFFFF and there are 5 of 4 OCTETs. This integer number is represented by 4 OCTETs. To match a BGP community access list. |
| OCT snBgp4RouteMapMatchAddressAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.13 | OCTET STRING | read-write | A number from 1 to 0xFFFF and there are 5 of 2 OCTETs. This integer number is represented by 2 OCTETs. To match a BGP address access list. |
| OCT snBgp4RouteMapMatchAddressPrefixList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.14 | OCTET STRING | read-write | Prefix list To match a BGP address access list. |
| OCT snBgp4RouteMapMatchNextHopAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.15 | OCTET STRING | read-write | A number from 1 to 0xFFFF and there are 5 of 2 OCTETs. This integer number is represented by 2 OCTETs. To match a BGP address access list. |
| OCT snBgp4RouteMapMatchNextHopPrefixList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.13.1.1.16 | OCTET STRING | read-write | Prefix list To match a BGP address access list. |
| snBgp4RouteMapSet | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14 | |||
| snBgp4RouteMapSetTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1 | not-accessible | Bgp4 Route Map Set table. | |
| snBgp4RouteMapSetEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1 | not-accessible | An entry in the Bgp4 Route Map Set table. | |
| OCT snBgp4RouteMapSetMapName | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.1 | OCTET STRING | read-only | An octet string of the route-map name, each character of the name is represented by one octet. |
| INT snBgp4RouteMapSetSequenceNum | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.2 | INTEGER | read-only | A sequence number for this particular route-map. |
| INT snBgp4RouteMapSetAsPathType | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.3 | INTEGER | read-write | To modify an autonomous system path for BGP routes. tag(0) - Converts the tag of a route into an autonomous system path. prepend(1) - Appends the string from snBgp4RouteMapSetAsPathString to the as-path of the route that is matched by the route map. |
| OCT snBgp4RouteMapSetAsPathString | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.4 | OCTET STRING | read-write | as-path string. This string is used if only if the snBgp4RouteMapSetAsPathCmd was sent together with the value set to prepend(1). |
| INT snBgp4RouteMapSetAutoTag | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.5 | INTEGER | read-write | To enable/disable the automatic-tag for BGP routes. |
| INT snBgp4RouteMapSetCommunityType | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.6 | INTEGER | read-write | To set the BGP COMMUNITIES attribute. none means no other community attributes are allowed, nums means allowing community attributesi, the old values 1 and 2 are not valid since 5.03.00 |
| INT snBgp4RouteMapSetCommunityNum | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.7 | INTEGER | read-write | community-number. This number is used if only if the snBgp4RouteMapSetCommunityCmd was sent together with the value set to number(0). |
| INT snBgp4RouteMapSetCommunityAdditive | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.8 | INTEGER | read-write | To add the community to the already existing communities. |
| INT snBgp4RouteMapSetLocalPreference | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.9 | INTEGER | read-write | To modify a local-preference for BGP routes. |
| INT snBgp4RouteMapSetMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.10 | INTEGER | read-write | To modify a metric for BGP routes. |
| IP snBgp4RouteMapSetNextHop | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.11 | IpAddress | read-write | To modify the IP address of the next hop for BGP routes. |
| INT snBgp4RouteMapSetOrigin | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.12 | INTEGER | read-write | To set the BGP origin code. |
| INT snBgp4RouteMapSetTag | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.13 | INTEGER | read-write | To specify the tag for BGP routes. |
| INT snBgp4RouteMapSetWeight | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.14 | INTEGER | read-write | To specify the BGP weight for the routing table. |
| INT snBgp4RouteMapSetRowMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.15 | INTEGER | read-write | This object is used together with above MIBs in the same VARBIND to set and reset any MIBs in the table. The bit number is referred to the snBgp4RouteMapSetEntry number of each row in the table. The bit is ON - means set, The bit is OFF - means reset |
| OCT snBgp4RouteMapSetCommunityNums | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.16 | OCTET STRING | read-write | Community number is from 1 to 0xFFFFFFFF. There are 6 of them. This integer number is represented by 4 OCTETs. |
| INT snBgp4RouteMapSetDampenHalfLife | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.17 | INTEGER | read-write | Bgp4 Route Map Dampening Half Life. |
| INT snBgp4RouteMapSetDampenReuse | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.18 | INTEGER | read-write | Bgp4 Route Map Dampening Reuse. |
| INT snBgp4RouteMapSetDampenSuppress | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.19 | INTEGER | read-write | Bgp4 Route Map Dampening Suppress. |
| INT snBgp4RouteMapSetDampenMaxSuppress | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.14.1.1.20 | INTEGER | read-write | Bgp4 Route Map Dampening Max Suppress Time. |
| snBgp4NeighOperStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15 | |||
| snBgp4NeighOperStatusTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1 | not-accessible | Bgp4 Neighbor Operational Status table. | |
| snBgp4NeighOperStatusEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1 | not-accessible | An entry in the Bgp4 Operational Status table. | |
| INT snBgp4NeighOperStatusIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.1 | INTEGER | read-only | The index for a neighbor entry. |
| IP snBgp4NeighOperStatusIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.2 | IpAddress | read-only | The IP Address for a neighbor entry. |
| INT snBgp4NeighOperStatusRemoteAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.3 | INTEGER | read-only | To show a neighbor with an autonomous system number(AS). |
| INT snBgp4NeighOperStatusBgpType | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.4 | INTEGER | read-only | To show the type of BGP protocol whether is internal or external. |
| INT snBgp4NeighOperStatusState | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.5 | INTEGER | read-only | To show the state of this neighbor. |
| INT snBgp4NeighOperStatusKeepAliveTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.6 | INTEGER | read-only | The Keep alive timer. |
| INT snBgp4NeighOperStatusHoldTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.7 | INTEGER | read-only | The Hold time timer. |
| INT snBgp4NeighOperStatusAdvertlevel | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.8 | INTEGER | read-only | To show the minimum interval between the sending of BGP routing updates. |
| CTR snBgp4NeighOperStatusKeepAliveTxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.9 | Counter | read-only | Keep alive message sent counts. |
| CTR snBgp4NeighOperStatusKeepAliveRxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.10 | Counter | read-only | Keep alive message received counts. |
| CTR snBgp4NeighOperStatusUpdateTxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.11 | Counter | read-only | Update message sent counts. |
| CTR snBgp4NeighOperStatusUpdateRxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.12 | Counter | read-only | Update message received counts. |
| CTR snBgp4NeighOperStatusNotifTxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.13 | Counter | read-only | Notification message sent counts. |
| CTR snBgp4NeighOperStatusNotifRxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.14 | Counter | read-only | Notification message received counts. |
| CTR snBgp4NeighOperStatusOpenTxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.15 | Counter | read-only | Open message sent counts. |
| CTR snBgp4NeighOperStatusOpenRxCounts | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.15.1.1.16 | Counter | read-only | Open message received counts. |
| snBgp4RouteOperStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16 | |||
| snBgp4RouteOperStatusTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1 | not-accessible | Bgp4 Routebor Operational Status table. | |
| snBgp4RouteOperStatusEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1 | not-accessible | An entry in the Bgp4 Operational Status table. | |
| INT snBgp4RouteOperStatusIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.1 | INTEGER | read-only | The index for a route entry. |
| IP snBgp4RouteOperStatusIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.2 | IpAddress | read-only | The IP Address for a route entry. |
| IP snBgp4RouteOperStatusSubnetMask | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.3 | IpAddress | read-only | The IP Subnet Mask for a route entry. |
| IP snBgp4RouteOperStatusNextHop | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.4 | IpAddress | read-only | The next-hop IP for a route entry. |
| INT snBgp4RouteOperStatusMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.5 | INTEGER | read-only | To show the metric value of a route entry. |
| INT snBgp4RouteOperStatusLocalPreference | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.6 | INTEGER | read-only | To show the local preference of a route entry. |
| INT snBgp4RouteOperStatusWeight | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.7 | INTEGER | read-only | To show the weight of this route. |
| INT snBgp4RouteOperStatusOrigin | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.8 | INTEGER | read-only | To show the origin of this route. |
| INT snBgp4RouteOperStatusStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.9 | INTEGER | read-only | A bit array that contains the status of this route. This is a packed bit string; The following shows the meaning of each bit: (bit 0 is the least significant bit and 0=FALSE, 1=TRUE). bit position meaning ------------ ------- 6-31 reserved. 5 aggregate. 4 best. 3 internal. 2 local. 1 suppressed. 0 valid. |
| INT snBgp4RouteOperStatusRouteTag | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.10 | INTEGER | read-only | To show the route tag of this route. |
| OCT snBgp4RouteOperStatusCommunityList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.11 | OCTET STRING | read-only | To show the community list of this route. If the community list is an NULL string that means an empty list, then the community is INTERNET. A number from 1 to 0xFFFFFFFF. This integer number is represented by 4 OCTETs. In the community list, it could have some Well-known numbers such as: BGP_COMMUNITY_ATTRIBUTE_NO_EXPORT 0xFFFFFF01 BGP_COMMUNITY_ATTRIBUTE_NO_ADVERTISE 0xFFFFFF02 |
| OCT snBgp4RouteOperStatusAsPathList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.16.1.1.12 | OCTET STRING | read-only | To show the AS Path list of this route. A number from 1 to 0xFFFF. This integer number is represented by 2 OCTETs. |
| snBgp4NeighborSummary | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17 | |||
| snBgp4NeighborSummaryTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1 | not-accessible | Bgp4 Routebor Operational Status table. | |
| snBgp4NeighborSummaryEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1 | not-accessible | An entry in the Bgp4 Operational Status table. | |
| INT snBgp4NeighborSummaryIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.1 | INTEGER | read-only | The index for a route entry. |
| IP snBgp4NeighborSummaryIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.2 | IpAddress | read-only | The IP Address for a route entry. |
| INT snBgp4NeighborSummaryState | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.3 | INTEGER | read-only | To show the state of this neighbor. |
| INT snBgp4NeighborSummaryStateChgTime | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.4 | INTEGER | read-only | The time of a change of the state of this neighbor. |
| INT snBgp4NeighborSummaryRouteReceived | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.5 | INTEGER | read-only | The number of routes received of this neighbor. |
| INT snBgp4NeighborSummaryRouteInstalled | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.17.1.1.6 | INTEGER | read-only | The number of routes installed of this neighbor. |
| snBgp4Attribute | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18 | |||
| snBgp4AttributeTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1 | not-accessible | Bgp4 Attribute entries table. | |
| snBgp4AttributeEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1 | not-accessible | An entry in the Bgp4 Attribute table. | |
| INT snBgp4AttributeIndex | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.1 | INTEGER | read-only | The index for a route entry. |
| IP snBgp4AttributeNextHop | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.2 | IpAddress | read-only | The next-hop IP for a route entry. |
| INT snBgp4AttributeMetric | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.3 | INTEGER | read-only | To show the metric value of a route entry. |
| INT snBgp4AttributeOrigin | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.4 | INTEGER | read-only | To show the origin of this route. |
| INT snBgp4AttributeAggregatorAs | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.5 | INTEGER | read-only | The aggregator AS number for an attribute entry. |
| IP snBgp4AttributeRouterId | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.6 | IpAddress | read-only | The router ID for an attribute entry. |
| INT snBgp4AttributeAtomicAggregatePresent | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.7 | INTEGER | read-only | The atomic aggregate present in an attribute entry. |
| INT snBgp4AttributeLocalPreference | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.8 | INTEGER | read-only | To show the local preference of a route entry. |
| OCT snBgp4AttributeCommunityList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.9 | OCTET STRING | read-only | To show the community list of this attribute entry. If the community list is an NULL string that means an empty list, then the community is INTERNET. A number from 1 to 0xFFFFFFFF. This integer number is represented by 4 OCTETs. In the community list, it could have some Well-known numbers such as: BGP_COMMUNITY_ATTRIBUTE_NO_EXPORT 0xFFFFFF01 BGP_COMMUNITY_ATTRIBUTE_NO_ADVERTISE 0xFFFFFF02 |
| OCT snBgp4AttributeAsPathList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.10 | OCTET STRING | read-only | To show the AS Path list of this attribute entry. A number from 1 to 0xFFFF. This integer number is represented by 2 OCTETs. |
| IP snBgp4AttributeOriginator | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.11 | IpAddress | read-only | The originator IP address for an attribute entry. |
| OCT snBgp4AttributeClusterList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.18.1.1.12 | OCTET STRING | read-only | To show the cluster list of this attribute entry. If the cluster list is an NULL string, it means an empty list. Otherwise, the list is a group of cluster ID which is represented by 4 OCTETs IP address. |
| snBgp4ClearNeighborCmd | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.19 | |||
| snBgp4ClearNeighborCmdTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1 | not-accessible | Clear Bgp4 command table. | |
| snBgp4ClearNeighborCmdEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1.1 | not-accessible | An entry in the clear Bgp4 neighbor command table. | |
| IP snBgp4ClearNeighborCmdIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1.1.1 | IpAddress | read-only | The IP Address for a neighbor entry. If the IP address is 255.255.255.255, it means for all neighbors. |
| INT snBgp4ClearNeighborCmdElement | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.19.1.1.2 | INTEGER | read-write | To send the command element of this neighbor for value(1) to (5) valid(0) is received in SNMP-get. |
| snBgp4NeighPrefixGroup | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.20 | |||
| snBgp4NeighPrefixGroupTable | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1 | not-accessible | Bgp4 Neighbor Prefix Group table. | |
| snBgp4NeighPrefixGroupEntry | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1 | not-accessible | An entry in the Bgp4 Prefix Group table. | |
| IP snBgp4NeighPrefixGroupNeighIp | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1.1 | IpAddress | read-only | The IP Address for a neighbor entry. |
| INT snBgp4NeighPrefixGroupDir | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1.2 | INTEGER | read-only | The incoming/outgoing advertisements to which the access list is applied. |
| OCT snBgp4NeighPrefixGroupInAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1.3 | OCTET STRING | read-write | An in access prefix list name. |
| OCT snBgp4NeighPrefixGroupOutAccessList | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1.4 | OCTET STRING | read-write | An out prefix list name. |
| INT snBgp4NeighPrefixGroupRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.2.11.20.1.1.5 | INTEGER | read-write | This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid |
RFC description
HP Foundry vendor MIB for Border Gateway Protocol (BGP) version 4 routing management on network switches.
Start monitoring HP ProCurve Routing Switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.