All MIBs › HP-ICF-PIM
Organization: HP Networking
Last Updated: 2012-04-12
Category: Routing Protocols, Technology: Multicast, Technology: Routing/L3, Vendor: HP/HPE
Description: HP ICF SNMP MIB for Protocol Independent Multicast (PIM) routing configuration and neighbor state on HP ProCurve switches.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HP-ICF-PIM?
HP-ICF-PIM is an HP-proprietary (ICF) SNMP module providing extensions to the standard PIM (Protocol Independent Multicast) MIB defined in RFC 2934, adding HP-specific management objects for PIM routing configuration and neighbor state on HP ProCurve switches. No concrete sample objects were supplied, so exact table names cannot be confirmed, but given its stated purpose it would expose PIM interface configuration and neighbor adjacency status. Its monitoring relevance is in confirming multicast routing protocol health, i.e., whether PIM neighbors are established on a given interface and whether multicast forwarding state is being built correctly, which is software/protocol status rather than hardware condition. It explicitly extends the standard PIM MIB (RFC 2934), so it should be read alongside that base MIB for full coverage. It is deployed on HP ProCurve Layer 3 switches that participate in multicast routing within enterprise or campus networks. Engineers can download the HP-ICF-PIM file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HP-ICF-PIM. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HP ProCurve Layer 3 switches
Monitoring Examples
No sample objects were provided for this module, so a specific scenario cannot cite real object names; in general, an operator would use this MIB's HP-specific extensions alongside the standard PIM MIB to check PIM neighbor state on a switch interface and confirm multicast routing adjacencies are established rather than stuck in an initializing state.
What Can Be Monitored
- PIM interface configuration
- PIM neighbor adjacency state
This MIB depends on
Related MIBs
Imported Objects
From HP-ICF-OID
| hpSwitch | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex |
From INET-ADDRESS-MIB
| InetAddress | |
| InetAddressPrefixLength | |
| InetAddressType |
From IPMROUTE-STD-MIB
| ipMRouteEntry | OBJECT-TYPE |
| ipMRouteGroup | OBJECT-TYPE |
| ipMRouteSource | OBJECT-TYPE |
From PIM-MIB
| pimComponentEntry | OBJECT-TYPE |
| pimInterfaceEntry | OBJECT-TYPE |
| pimInterfaceIfIndex | OBJECT-TYPE |
| pimNeighborEntry | OBJECT-TYPE |
| pimRPSetComponent | OBJECT-TYPE |
| pimRPSetEntry | OBJECT-TYPE |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hpicfPimMIB | 1.3.6.1.4.1.11.2.14.11.5.1.20 | This MIB module contains HP proprietary extensions to the standard PIM MIB (RFC 2934). | ||
| hpicfPimObjects | 1.3.6.1.4.1.11.2.14.11.5.1.20.1 | |||
| hpicfPimTraps | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.0 | |||
| NTF hpicfPimHardMRTFull | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.0.1 | This notification signifies that the MRT table is full and the error has been originated by hardware. This trap should be generated whenever a multicast flow or MRT entry cannot be added. | ||
| NTF hpicfPimSoftMRTFull | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.0.2 | This notification signifies that the MRT table is full and the error has been originated by software. This trap should be generated whenever a multicast flow or MRT entry cannot be added. | ||
| hpicfPim | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1 | |||
| INT hpicfPimAdminStatus | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.1 | INTEGER | read-write | The operational status of the PIM routing protocol on this router. Default is disabled. |
| I32 hpicfPimStateRefreshInterval | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.2 | Integer32 | read-write | The interval between successive State Refresh messages originated by this router. Its default value is 60 seconds. The maximum value allowed in PIM for State Refresh interval will be 100. |
| I32 hpicfPimSPTThreshold | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.3 | Integer32 | read-write | Specifies a threshold for switching to the Shortest Path Tree (SPT) on this router. If the object has the special value of -1, the Shared Tree rooted to the Rendezvous Point (RP) will be used indefinitely on the router. Default is -1. |
| BIT hpicfPimTrapControl | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.4 | Bits | read-write | Indicates whether the PIM-enabled router will generate SNMP traps for PIM events. The set bit means 'enabled'. - neighborLoss(0) This bit controls whether the notification trap is allowed to be sent when the neighbor timer expires and the router has no other neighbors on the same interface with a lower IP address than itself. - hardMrtFull(1) This bit controls whether the notification trap is allowed to be sent when the MRT table is full and the error has been originated by hardware. - softMrtFull(2) This bit controls whether the notification trap is allowed to be sent when the MRT table is full and the error has been originated by software. |
| hpicfPimStaticRPSetTable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.5 | not-accessible | The (conceptual) table containing statically configured Rendezvous Points (RPs) for IP multicast group mappings. This information is being used in the PIM Sparse mode only. | |
| hpicfPimStaticRPSetEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.5.1 | not-accessible | An entry (row) in the hpicfPimStaticRPSetTable. NOTE: the pimRPSetComponent is an index that uniquely identifies the component. Each protocol instance connected to a separate domain should have a different index value. | |
| IP hpicfPimStaticRPSetGroupAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.5.1.1 | IpAddress | not-accessible | The IP multicast group address which, when combined with hpicfPimStaticRPSetGroupMask, gives the group prefix for which this entry contains information about the statically configured RP. |
| IP hpicfPimStaticRPSetGroupMask | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.5.1.2 | IpAddress | not-accessible | The multicast group address mask which, when combined with hpicfPimStaticRPSetGroupAddress, gives the group prefix for which this entry contains information about the statically configured RP. |
| IP hpicfPimStaticRPSetAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.5.1.3 | IpAddress | not-accessible | The IP address of statically configured RP for the given IP multicast group(s). |
| T/F hpicfPimStaticRPSetOverride | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.5.1.4 | TruthValue | read-create | If true, indicates that the router should ignore the information learned by a BSR if there is a conflict between the information this static entry contains and the information that is learned by the BSR. Default is false. |
| ROW hpicfPimStaticRPSetRowStatus | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.5.1.5 | RowStatus | read-create | The status of this row, by which new entries may be created, or old entries deleted from this table. |
| hpicfPimIfTable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6 | not-accessible | HP extensions to the pimInterfaceTable. | |
| hpicfPimIfEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1 | not-accessible | HP extensions for an entry in the pimInterfaceTable. | |
| IP hpicfPimIfAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.1 | IpAddress | read-create | This is copy of pimInterfaceAddress with read-create access. PIM uses this source address to send its protocol packets out on this interface. This address can be set to one of IP addresses of the interface or 255.255.255.255 if the address is determined dynamically based on the current IP configuration. The currently used source address is value of pimInterfaceAddress in the latter case. |
| I32 hpicfPimIfTrigHelloInterval | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.2 | Integer32 | read-create | The maximum time before a triggered PIM Hello message is transmitted on this interface. Default is 5 seconds. |
| I32 hpicfPimIfHelloHoldtime | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.3 | Integer32 | read-create | The value set in the Holdtime field of Hello messages transmitted on this interface. This should be 3.5 times the value of pimInterfaceHelloInterval. Default is 105 seconds. |
| T/F hpicfPimIfLanPruneDelay | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.4 | TruthValue | read-create | Turns the LAN Prune Delay options ON and OFF, on this interface. Default is true. |
| I32 hpicfPimIfPropagationDelay | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.5 | Integer32 | read-create | The value inserted into the LAN Prune Delay field of a LAN Prune Delay option on this interface. Default is 500 milliseconds. |
| I32 hpicfPimIfOverrideInterval | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.6 | Integer32 | read-create | The value inserted into the Override Interval field of a LAN Prune Delay option on this interface. Default is 2500 milliseconds. |
| T/F hpicfPimIfGenerationID | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.7 | TruthValue | read-create | Turns the Generation ID option ON and OFF, on this interface. Default is false. |
| U32 hpicfPimIfJoinPruneHoldtime | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.8 | Unsigned32 | read-create | The value inserted into the Holdtime field of a Join/ Prune message sent on this interface. The value should be 3.5 times pimInterfaceJoinPruneInterval. Default is 210 seconds. |
| I32 hpicfPimIfGraftRetryInterval | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.9 | Integer32 | read-create | The interval a PIM router waits for a Graft Ack before re-sending a Graft on this interface. Default is 3 seconds. |
| I32 hpicfPimIfMaxGraftRetries | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.10 | Integer32 | read-create | The maximum number of times this router will re-send a Graft on this interface. Default is 2. |
| U32 hpicfPimIfSRTTLThreshold | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.11 | Unsigned32 | read-create | The Time To Live in a PIM-DM State Refresh message at which it is not forwarded on this interface. Default is 0. |
| T/F hpicfPimIfLanDelayEnabled | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.12 | TruthValue | read-only | Evaluates to TRUE if all routers on this interface are using the LAN Prune Delay Option. |
| T/F hpicfPimIfSRCapable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.13 | TruthValue | read-only | Evaluates to TRUE if all routers on this interface are using the State Refresh Capable Option. |
| U32 hpicfPimIfDRPriority | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.14 | Unsigned32 | read-create | The Designated Router Priority inserted into the DR priority option on this interface. Default is 1. |
| I32 hpicfPimIfNBRTimeout | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.15 | Integer32 | read-create | Time interval after which the router will consider a neighbor to not be present, if no PIM Hello messages arrived on the interface. Default is 180 seconds. |
| C32 hpicfPimIfNBRCount | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.16 | Counter32 | read-only | PIM Neighbor Count. |
| TIK hpicfPimIfNegotiatedPropagationDelay | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.17 | TimeTicks | read-only | Negotiated PIM LAN/Propagation Delay (ms). |
| TIK hpicfPimIfNegotiatedOverrideInterval | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.18 | TimeTicks | read-only | Negotiated PIM Override Interval (ms). |
| C32 hpicfPimIfAssertHoldInterval | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.19 | Counter32 | read-only | PIM Assert Hold Interval (s). |
| C32 hpicfPimIfNumRoutersNotUsingDRPriority | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.20 | Counter32 | read-only | Number of routers on network not using DR priority. |
| C32 hpicfPimIfNumRoutersNotUsingLanDelay | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.6.1.21 | Counter32 | read-only | Number of routers on network not using LAN Delay. |
| hpicfPimComponentTable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7 | not-accessible | HP extensions to the pimComponentTable - the (conceptual) table containing objects specific to a PIM domain. One row exists for each domain to which the router is connected. Typically, a PIM-SM router will be a member of exactly one domain, however, the table also supports routers which may form a border between two PIM-SM domains and do not forward Bootstrap messages between them. | |
| hpicfPimComponentEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1 | not-accessible | HP extensions for an entry in the pimComponentTable. | |
| INT hpicfPimComponentCBSRAdminStatus | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.1 | INTEGER | read-create | This objects specifies whether or not the router configured to be a Candidate BSR for the local PIM region. Default is disabled. |
| IP hpicfPimComponentCBSRAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.2 | IpAddress | read-create | The IP address the Candidate BSR router will advertise for the local PIM region. |
| I32 hpicfPimComponentCBSRPriority | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.3 | Integer32 | read-create | The priority for Candidate BSR router. In BSR election process the candidate BSR with the highest (numerically bigger) priority becomes the BSR. If the priority values are the same, the router with the larger IP address is the BSR. Default is 0. |
| I32 hpicfPimComponentCBSRHashMaskLength | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.4 | Integer32 | read-create | Specifies the length (in bits) of a multicast group address to use when mapping a group to one of the candidate RPs from the RP-Set whose group-prefix includes the group. The recommended value for IPv4 is 30, for IPv6 is 126. Default is 30. |
| I32 hpicfPimComponentCBSRMessageInterval | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.5 | Integer32 | read-create | If this router is the elected BSR, this object is the interval for sending (multicast out) periodic Bootstrap (RP-Set) messages on all PIM SM interfaces. The acceptable range is 5-300. The default value of this object is 60 seconds. |
| I32 hpicfPimComponentCRPPriority | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.6 | Integer32 | read-create | The priority for the Candidate RP for the local PIM domain. Determines which Candidate RPs get selected by the BSR to be in the RP Set. The smaller value means the higher priority (a value of zero is the highest possible priority). Default is 192. |
| U32 hpicfPimComponentCRPAdvInterval | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.7 | Unsigned32 | read-only | The interval at which the Candidate RP transmits (unicast to the elected BSR) advertise messages in the local PIM domain. |
| U32 hpicfPimComponentBSRPriority | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.8 | Unsigned32 | read-only | The priority of the Bootstrap Router (BSR) elected for the local PIM region. |
| U32 hpicfPimComponentBSRHashMaskLength | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.9 | Unsigned32 | read-only | The hash mask length of the elected Bootstrap Router (BSR). |
| TIK hpicfPimComponentBSRUpTime | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.10 | TimeTicks | read-only | Length of time that the elected Bootstrap Router (BSR) has been up. |
| TIK hpicfPimComponentBSRNextMessage | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.11 | TimeTicks | read-only | Time in which the next bootstrap message is due from the elected Bootstrap Router (BSR). |
| TIK hpicfPimComponentCRPAdvTimer | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.7.1.12 | TimeTicks | read-only | Next scheduled Candidate RP Advertisement. |
| T/F hpicfPimRemoveConfig | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.8 | TruthValue | read-write | PIM is halted. This objects clears all existing PIM configuration, intializes the pim config to the default state. SnmpGet on this will always return false. An SnmpSet of false has no effect. |
| hpicfPimStaticRpfTable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9 | not-accessible | The (conceptual) table containing statically configured reverse path forwarding (RPF) source address to interface mappings. This information is currently used in the PIM sparse mode only. | |
| hpicfPimStaticRpfEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9.1 | not-accessible | A row in the hpicfPimStaticRpfTable. | |
| IPt hpicfPimStaticRpfSourceAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9.1.1 | InetAddressType | not-accessible | The IP address type of the statically configured multicast source. |
| IP hpicfPimStaticRpfSourceAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9.1.2 | InetAddress | not-accessible | The IP address of the statically configured multicast source. |
| ADR hpicfPimStaticRpfSourcePrefixLength | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9.1.3 | InetAddressPrefixLength | not-accessible | The prefix length of the statically configured multicast source. |
| IPt hpicfPimStaticRpfAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9.1.4 | InetAddressType | not-accessible | The type of RPF address for this route. The value of this object must be equal to a value appropriate for the corresponding instance of the hpicfPimStaticRpfSourceAddressType object. |
| IP hpicfPimStaticRpfAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9.1.5 | InetAddress | not-accessible | The IP address of the interface to use for RPF checks. |
| ROW hpicfPimStaticRpfRowStatus | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9.1.6 | RowStatus | read-create | The status of this row, by which new entries may be created, or old entries deleted from this table. |
| INT hpicfPimStaticRpfOverrideState | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9.1.7 | INTEGER | read-only | The state of this RPF override entry. |
| NUM hpicfPimStaticRpfIfIndex | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9.1.8 | InterfaceIndex | read-only | Index of the Interface towards the RPF neighbor. |
| IPt hpicfPimStaticRpfNeighborAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9.1.9 | InetAddressType | read-only | The IP address type of the statically configured RPF neighbor. |
| IP hpicfPimStaticRpfNeighborAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.9.1.10 | InetAddress | read-only | The IP address of the static RPF Neighbor. |
| C32 hpicfPimNumStaticRpfEntries | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.10 | Counter32 | read-only | Total number of Static RPF entries. |
| C32 hpicfPimVersion | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.11 | Counter32 | read-only | Currently running PIM Version. |
| C32 hpicfPimStarGEntries | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.12 | Counter32 | read-only | Total number of entries in the (*,G) table |
| C32 hpicfPimSGEntries | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.13 | Counter32 | read-only | Total number of entries in the (S,G) table. |
| hpicfPimMRouteTable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14 | not-accessible | HP extensions to rfc2932's ipMRouteEntry table. | |
| hpicfPimMRouteEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1 | not-accessible | HP extensions for an entry in ipMRouteEntry. | |
| T/F hpicfPimSendRegStop | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.1 | TruthValue | read-only | Indicates that a register-stop message must be sent. |
| T/F hpicfPimSGSourceIsActive | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.2 | TruthValue | read-only | Indicates whether the multicast source corresponding to the (S,G) is active. |
| T/F hpicfPimOutgoingRegisterIfAvailable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.3 | TruthValue | read-only | Indicates that a register outgoing interface is available. |
| T/F hpicfPimEntryAddSuccess | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.4 | TruthValue | read-only | Indicates that an entry has been successfully added. |
| C32 hpicfPimNumOutgoingInterfaces | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.5 | Counter32 | read-only | List of outgoing interfaces. |
| T/F hpicfPimDirectlyConnectedSource | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.6 | TruthValue | read-only | Specifies PIM routing entries on routers directly connecting to the same subnet with the multicast source. |
| T/F hpicfPimNeighborSearchFailure | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.7 | TruthValue | read-only | Specifies PIM routing entries with PIM neighbor searching failure. |
| T/F hpicfPimRPTreePruneSent | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.8 | TruthValue | read-only | Specifies PIM routing entries on RPT branches where (S, G) prunes have been sent to the RP. |
| T/F hpicfPimOnSPTree | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.9 | TruthValue | read-only | Specifies PIM routing entries on the SPT. |
| T/F hpicfPimRPToSPTreeSwitching | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.10 | TruthValue | read-only | Specifies PIM routing entries in the process of RPT-to-SPT switchover. |
| T/F hpicfPimWildcardEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.11 | TruthValue | read-only | Specifies wildcard routing entries. |
| IPt hpicfPimRPFPrimeNeighborAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.12 | InetAddressType | read-only | RPF Prime Neighbor address type |
| IP hpicfPimRPFPrimeNeighborAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.13 | InetAddress | read-only | RPF Prime Neighbor address |
| C32 hpicfPimNumDownstreams | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.14.1.14 | Counter32 | read-only | Total number of downstreams. |
| C32 hpicfPimTotalNeighborCount | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.15 | Counter32 | read-only | PIM Neighbor Count. |
| hpicfPimNeighborTable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.16 | not-accessible | HP extensions to the pimNeighborTable. | |
| hpicfPimNeighborEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.16.1 | not-accessible | HP extensions for an entry in the pimNeighborTable. | |
| C32 hpicfPimNeighborDRPriority | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.16.1.1 | Counter32 | read-only | PIM Neighbor Router's Designated Router Priority value. |
| C32 hpicfPimNeighborGenerationIDValue | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.16.1.2 | Counter32 | read-only | PIM Neighbor Router's Generation ID value. |
| C32 hpicfPimNeighborHoldtime | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.16.1.3 | Counter32 | read-only | PIM Neighbor Router's Hold Time value. |
| C32 hpicfPimNeighborPropagationDelay | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.16.1.4 | Counter32 | read-only | PIM Neighbor Router's LAN Delay value. |
| C32 hpicfPimNeighborOverrideInterval | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.16.1.5 | Counter32 | read-only | PIM Neighbor Router's Override Interval value. |
| C32 hpicfPimNeighborStateRefreshInterval | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.16.1.6 | Counter32 | read-only | PIM Neighbor Router's State Refresh Interval value. |
| hpicfPimUcastRouteTable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.17 | not-accessible | Cached Unicast Route related to PIM. | |
| hpicfPimUcastRouteEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.17.1 | not-accessible | An entry in pimUcastRouteTable. | |
| IPt hpicfPimUcastRouteAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.17.1.1 | InetAddressType | not-accessible | Address family of a Unicast IP Address of a Source or network. |
| IP hpicfPimUcastRouteAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.17.1.2 | InetAddress | not-accessible | Unicast IP Address of a Source or network. |
| U32 hpicfPimUcastRoutePrefix | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.17.1.3 | Unsigned32 | not-accessible | Network Prefix length in bits of the address. |
| NUM hpicfPimUcastRouteIfIndex | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.17.1.4 | InterfaceIndex | read-only | Index of the Interface towards the source/network. |
| IPt hpicfPimUcastRouteUpstreamNbrType | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.17.1.5 | InetAddressType | read-only | Address type of the PIM neighbor on Interface towards the source/network. |
| IP hpicfPimUcastRouteUpstreamNbr | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.17.1.6 | InetAddress | read-only | Address of the PIM neighbor on the Interface towards the source/network. |
| U32 hpicfPimUcastRouteProtocol | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.17.1.7 | Unsigned32 | read-only | Unicast routing protocol through which the route was learned. |
| hpicfPimJoinPruneTable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.18 | not-accessible | Info on Join-Prune messages to send | |
| hpicfPimJoinPruneEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.18.1 | not-accessible | An entry in hpicfPimJoinPruneTable. | |
| NUM hpicfPimJoinPruneInterface | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.18.1.1 | InterfaceIndex | not-accessible | Interface on which Join-Prune messages will be sent. |
| INT hpicfPimJoinPruneInterfaceState | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.18.1.2 | INTEGER | not-accessible | Flag indicating a (S,G)/(*,G) join or (S,G,Rpt) prune. |
| IPt hpicfPimJoinPruneSourceType | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.18.1.3 | InetAddressType | not-accessible | Flow source address type for a (S,G) join or (S,G,Rpt) prune. |
| IP hpicfPimJoinPruneSourceAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.18.1.4 | InetAddress | not-accessible | Flow source address for a (S,G) join or (S,G,Rpt) prune. |
| IPt hpicfPimJoinPruneGroupType | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.18.1.5 | InetAddressType | not-accessible | Flow group address type for a (S,G)/(*,G) join or (S,G,Rpt) prune. |
| IP hpicfPimJoinPruneGroupAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.18.1.6 | InetAddress | not-accessible | Flow group address for a (S,G)/(*,G) join or (S,G,Rpt) prune. |
| IPt hpicfPimJoinPruneNeighborAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.18.1.7 | InetAddressType | read-only | PIM neighbor router address type towards the source/RP to which Join-Prune messages are sent. |
| IP hpicfPimJoinPruneNeighborAddress | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.18.1.8 | InetAddress | read-only | PIM neighbor router address towards the source/RP to which Join-Prune messages are sent. |
| U32 hpicfPimJoinPruneExpiryTime | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.18.1.9 | Unsigned32 | read-only | Expiry time of sending Join-Prune messages. |
| hpicfPimRPSetTable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.19 | not-accessible | Extensions to rfc2943's pimRPSetTable. | |
| hpicfPimRPSetEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.19.1 | not-accessible | An entry in pimUcastRouteTable. | |
| C32 hpicfPimRPSetPriority | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.19.1.1 | Counter32 | read-only | RP Set Priority. |
| TIK hpicfPimRPSetUptime | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.19.1.2 | TimeTicks | read-only | Time RP has been up. |
| hpicfPimIfMessageCounterTable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20 | not-accessible | Table of per-interface message counters. | |
| hpicfPimIfMessageCounterEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1 | not-accessible | An entry in hpicfPimIfMessageCounterTable. | |
| C32 hpicfPimIfMsgCountAssertReceive | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.1 | Counter32 | read-only | Per-interface count of received Assert messages. |
| C32 hpicfPimIfMsgCountAssertTransmit | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.2 | Counter32 | read-only | Per-interface count of transmitted Assert messages. |
| C32 hpicfPimIfMsgCountAssertInvalid | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.3 | Counter32 | read-only | Per-interface count of invalid Assert messages received. |
| C32 hpicfPimIfMsgCountGraftReceive | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.4 | Counter32 | read-only | Per-interface count of received Graft messages. |
| C32 hpicfPimIfMsgCountGraftTransmit | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.5 | Counter32 | read-only | Per-interface count of transmitted Graft messages. |
| C32 hpicfPimIfMsgCountGraftInvalid | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.6 | Counter32 | read-only | Per-interface count of invalid Graft messages received. |
| C32 hpicfPimIfMsgCountGraftAckReceive | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.7 | Counter32 | read-only | Per-interface count of received Graft-Ack messages. |
| C32 hpicfPimIfMsgCountGraftAckTransmit | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.8 | Counter32 | read-only | Per-interface count of transmitted Graft-Ack messages. |
| C32 hpicfPimIfMsgCountGraftAckInvalid | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.9 | Counter32 | read-only | Per-interface count of invalid Graft-Ack messages received. |
| C32 hpicfPimIfMsgCountHelloReceive | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.10 | Counter32 | read-only | Per-interface count of received HELLO messages. |
| C32 hpicfPimIfMsgCountHelloTransmit | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.11 | Counter32 | read-only | Per-interface count of transmitted HELLO messages. |
| C32 hpicfPimIfMsgCountHelloInvalid | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.12 | Counter32 | read-only | Per-interface count of invalid HELLO messages received. |
| C32 hpicfPimIfMsgCountJPReceive | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.13 | Counter32 | read-only | Per-interface count of received Join-Prune messages. |
| C32 hpicfPimIfMsgCountJPTransmit | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.14 | Counter32 | read-only | Per-interface count of transmitted Join-Prune messages. |
| C32 hpicfPimIfMsgCountJPInvalid | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.15 | Counter32 | read-only | Per-interface count of invalid Join-Prune messages received. |
| C32 hpicfPimIfMsgCountSRReceive | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.16 | Counter32 | read-only | Per-interface count of received State-Refresh messages. |
| C32 hpicfPimIfMsgCountSRTransmit | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.17 | Counter32 | read-only | Per-interface count of transmitted State-Refresh messages. |
| C32 hpicfPimIfMsgCountSRInvalid | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.18 | Counter32 | read-only | Per-interface count of invalid State-Refresh messages received. |
| C32 hpicfPimIfMsgCountBSRReceive | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.19 | Counter32 | read-only | Per-interface count of received BSR messages. |
| C32 hpicfPimIfMsgCountBSRTransmit | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.20 | Counter32 | read-only | Per-interface count of transmitted BSR messages. |
| C32 hpicfPimIfMsgCountBSRInvalid | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.21 | Counter32 | read-only | Per-interface count of invalid BSR messages received. |
| C32 hpicfPimIfMsgCountCRPReceive | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.22 | Counter32 | read-only | Per-interface count of received Candidate-RP messages. |
| C32 hpicfPimIfMsgCountCRPTransmit | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.23 | Counter32 | read-only | Per-interface count of transmitted Candidate-RP messages. |
| C32 hpicfPimIfMsgCountCRPInvalid | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.20.1.24 | Counter32 | read-only | Per-interface count of invalid Candidate-RP messages received. |
| hpicfPimUnackGraftsTable | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.21 | not-accessible | Information about unacknowledged graft messages on the network. | |
| hpicfPimUnackGraftsEntry | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.21.1 | not-accessible | An entry in hpicfPimUnackGraftsTable. | |
| IPt hpicfPimUnackGraftSourceType | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.21.1.1 | InetAddressType | not-accessible | Flow Source address type for an unacknowledged Graft message on the network. |
| IP hpicfPimUnackGraftSource | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.21.1.2 | InetAddress | not-accessible | Flow Source address for an unacknowledged Graft message on the network. |
| IPt hpicfPimUnackGraftGroupType | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.21.1.3 | InetAddressType | not-accessible | Flow Group address type for an unacknowledged Graft message on the network. |
| IP hpicfPimUnackGraftGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.21.1.4 | InetAddress | not-accessible | Flow Group address for an unacknowledged graft message on the network. |
| C32 hpicfPimUnackGraftAge | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.21.1.5 | Counter32 | read-only | Time in which the graft message will be timed-out. |
| C32 hpicfPimUnackGraftRetransIn | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.1.21.1.6 | Counter32 | read-only | Time in which the graft message will be retransmitted. |
| hpicfPimScalars | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.2 | |||
| C32 hpicfPimMsgCountRegisterReceive | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.2.1 | Counter32 | read-only | Global count of received Register messages. |
| C32 hpicfPimMsgCountRegisterTransmit | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.2.2 | Counter32 | read-only | Global count of transmitted Register messages. |
| C32 hpicfPimMsgCountRegisterInvalid | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.2.3 | Counter32 | read-only | Global count of invalid Register messages received. |
| C32 hpicfPimMsgCountRegStopReceive | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.2.4 | Counter32 | read-only | Global count of received Register-stop messages. |
| C32 hpicfPimMsgCountRegStopTransmit | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.2.5 | Counter32 | read-only | Global count of transmitted Register-stop messages. |
| C32 hpicfPimMsgCountRegStopInvalid | 1.3.6.1.4.1.11.2.14.11.5.1.20.1.2.6 | Counter32 | read-only | Global count of invalid Register-stop messages received. |
| hpicfPimConformance | 1.3.6.1.4.1.11.2.14.11.5.1.20.2 | |||
| hpicfPimGroups | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1 | |||
| hpicfPimNotificationGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.1 | A collection of notifications that extends notifications defined in RFC 2934 - used for signaling important PIM events. | ||
| hpicfPimBaseGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.2 | A collection of objects to support basic PIM configuration information on HP routers. | ||
| hpicfPimStaticRPSetMappingGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.3 | A collection of objects to support management of static Rendezvous Point (RP) to IP multicast group mappings. | ||
| hpicfPimSparseIfGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.4 | A collection of objects that extends objects defined in pimInterfaceTable and used to support management of interfaces operating in PIM Sparse Mode. | ||
| hpicfPimDenseIfGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.5 | A collection of objects that extends objects defined in pimInterfaceTable and used to support management of interfaces operating in PIM Dense Mode. | ||
| hpicfPimComponentGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.6 | A collection of objects that extends objects defined in pimComponentTable (RFC 2934). | ||
| hpicfPimStaticRpfGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.7 | A collection of objects defined in hpicfPimStaticRpfTable. | ||
| hpicfPimInterfaceExtensionsGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.8 | A collection of objects that extends objects defined in pimInterfaceTable. | ||
| hpicfPimStaticRpfExtensionsGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.9 | A collection of objects that extend hpicfPimStaticRpfTable. | ||
| hpicfPimNeighborGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.10 | A collection of objects defined in hpicfPimNeighborTable. | ||
| hpicfPimMRouteGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.11 | A collection of objects defined in hpicfMRouteTable. | ||
| hpicfPimUcastRouteGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.12 | A collection of objects defined in hpicfUcastRouteTable. | ||
| hpicfPimUnackGraftsGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.13 | A collection of objects defined in hpicfUnackGraftTable. | ||
| hpicfPimGlobalCounterGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.14 | A collection of global PIM counter objects. | ||
| hpicfPimRPSetGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.15 | A collection of additional RP & BSR objects. | ||
| hpicfPimJoinPruneGroup | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.1.17 | A collection of objects defined in hpicfPimJoinPruneTable. | ||
| hpicfPimCompliances | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.2 | |||
| hpicfPimSparseMIBCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.2.1 | The compliance statement for HP routers running PIM Sparse Mode and implementing the HP-ICF-PIM MIB. | ||
| hpicfPimDenseMIBCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.2.2 | The compliance statement for HP routers running PIM Dense Mode and implementing the HP-ICF-PIM MIB. | ||
| hpicfPimNotificationCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.2.3 | The collection of notifications that extends notifications defined in RFC 2934 - used for signalling important PIM events. | ||
| hpicfPimUcastRoutingCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.2.4 | The compliance statement for HP routers running PIM and related Unicast routing info. | ||
| hpicfPimMcastRoutingCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.2.5 | The compliance statement for HP routers running PIM and related multicast forwarding info. | ||
| hpicfPimInterfaceInfoCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.2.6 | The compliance statement for HP routers running PIM and related interface and neighbor info. | ||
| hpicfPimProtoMessageCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.2.7 | The compliance statement for HP routers running PIM and certain protocol packet info. | ||
| hpicfPimGlobalCountersCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.2.8 | The compliance statement for HP routers running PIM and related global statistics data. | ||
| hpicfPimRPSetExtensionsCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.20.2.2.9 | The compliance statement for HP routers running PIM Sparse Mode and further RP set info. |
RFC description
HP Protocol Independent Multicast (PIM) extensions for managing multicast routing and group membership.
Start monitoring HP ProCurve Layer 3 switch (PIM multicast routing) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.