All MIBs › HP-ICF-MLD-MIB
Organization: HP Networking
Last Updated: 2015-09-11
Category: Technology: IPv6, Technology: Multicast, Vendor: HP/HPE
Description: HP ICF SNMP MIB for Multicast Listener Discovery (MLD) snooping configuration and statistics on HP ProCurve switches.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HP-ICF-MLD-MIB?
HP-ICF-MLD-MIB is a vendor-specific HP (ProCurve/Aruba Networking) MIB that extends the standard MLD MIB (RFC 3019) with additional objects for managing IPv6 Multicast Listener Discovery snooping and querier behavior on HP switches. It augments the standard mldInterfaceEntry with per-interface querier state (hpicfMldIfEntryState) and a large set of protocol counters (report/query/leave rx/tx, malformed and bad-checksum packet counts), and adds a group-membership cache (hpicfMldCacheTable, with hpicfMldCacheUpTime, hpicfMldCacheExpiryTime, and hpicfJoinedPorts) alongside per-port mode control in hpicfMldPortConfigTable (forced-leave and fast-leave features). Monitoring it reveals whether MLD snooping/querier election is working correctly and whether ports are tracking multicast group joins as expected, which matters for diagnosing IPv6 multicast flooding or lost video/streaming traffic on switched networks. It depends on the standard IPV6-MLD-MIB for its base interface table and on Q-BRIDGE-MIB for port-list representations, and administrators can download the HP-ICF-MLD-MIB file to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HP-ICF-MLD-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- HP ProCurve / Aruba Networking switches (IPv6 multicast/MLD snooping capable)
Monitoring Examples
An operator polls hpicfMldCacheTable entries (hpicfMldCacheUpTime, hpicfMldCacheExpiryTime, hpicfJoinedPorts) alongside hpicfMldIfEntryStatMldV1ReportRx/V2ReportRx counters for a VLAN; a cache entry whose expiry timer is counting down without a corresponding report increment flags a host that stopped renewing membership, meaning the group may soon be pruned and multicast traffic cut off.
What Can Be Monitored
- MLD interface querier/non-querier state
- MLD protocol packet counters (queries, reports, leaves, malformed packets)
- multicast group cache entries and expiry timers
- per-port MLD mode and fast/forced-leave configuration
- filtered vs. standard group join counts
This MIB depends on
Related MIBs
Imported Objects
From HP-ICF-OID
| hpSwitch | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex |
From INET-ADDRESS-MIB
| InetAddressIPv6 |
From IPV6-MLD-MIB
| mldInterfaceEntry | OBJECT-TYPE |
From Q-BRIDGE-MIB
| PortList |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| TimeTicks | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using hpicfMldIfEntryStatGeneralQueryRx OID:
Select an HP ProCurve/Aruba switch (IPv6 MLD snooping/querier) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpicfMldIfEntryStatGeneralQueryRx into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of times an Mld General Service Query has been received on this interface. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hpicfMldMIB | 1.3.6.1.4.1.11.2.14.11.5.1.48 | This MIB module contains HP proprietary MIB definitions for managing MLD services including extensions to the standard MLD MIB (RFC 3019). | ||
| hpicfMldObjects | 1.3.6.1.4.1.11.2.14.11.5.1.48.1 | |||
| hpicfMld | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1 | |||
| T/F hpicfMldControlUnknownMulticast | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.1 | TruthValue | read-write | When enabled along with MLD, any IPv6 Multicast packets that are not joined by an MLD host will will be restricted to ports that have detected a multicast router or ports that are configured to always forward IPv6 multicast. When set to disabled or when MLD is disabled, the unjoined IPv6 multicast packets will be flooded out all ports in the VLAN. Permanently assigned multicast addresses are always flooded and so are not impacted by this object. |
| I32 hpicfMldConfigForcedLeaveInterval | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.2 | Integer32 | read-write | When a port's hpicfMldPortConfigEntryForcedLeaveFeature is enabled, this is the amount of time allowed for an MLD Report to arrive and cancel deletion of a multicast group requested by a previous MLD Leave request. Units are tenths of seconds. |
| I32 hpicfMldEnabledCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.3 | Integer32 | read-only | Current total count of interfaces with MLD enabled. |
| I32 hpicfMldMcastGroupJoinsCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.4 | Integer32 | read-only | Current total count of Multicast groups joined. |
| hpicfMldIfTable | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5 | not-accessible | HP extensions to the MLD standard MIB table mldIfTable. | |
| hpicfMldIfEntry | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1 | not-accessible | HP extensions for an entry in the mldInterfaceTable. | |
| T/F hpicfMldIfEntryQuerierFeature | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.1 | TruthValue | read-write | Turns MLD querier functionality on and off. |
| T/F hpicfMldIfEntrySnoopingFeature | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.2 | TruthValue | read-write | When enabled along with MLD, any IPv6 Multicast packets that are joined by an MLD host will be be restricted to ports which have received the joins. This can be overridden by other features like hpicfMldPortConfigEntryPortModeFeature. |
| I32 hpicfMldIfEntryQuerierPort | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.3 | Integer32 | read-only | Logical port which the querier is connected to. This is determined by the presence of querier packets on this port. This value is 0 if this device is querier. |
| I32 hpicfMldIfEntryFilteredJoins | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.4 | Integer32 | read-only | Current total count of groups on this interface being tracked on a per port basis. Traffic for these groups will be filtered to flow only to ports with active joins, subject to HW resource limitations such as the maximum number of groups supported by the hardware. |
| I32 hpicfMldIfEntryStandardJoins | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.5 | Integer32 | read-only | Current total count of groups on this interface being traced on a per interface basis. Traffic for these groups are flooded to the ports on the interface. These can come form joinees on interfaces which do not have MLD snooping turned on. They can also come from interfaces which have MLD snooping on, but HW resources have been exhausted for bridging traffic based on joins. |
| POR hpicfMldIfEntryPortsWithMcastRouter | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.6 | PortList | read-only | This indicates which ports have a multicast router detected on them. |
| C32 hpicfMldIfEntryStatGeneralQueryRxEx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.7 | Counter32 | read-only | The number of times an Mld General Service Query has been received on this interface. |
| C32 hpicfMldIfEntryStatQueryTx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.8 | Counter32 | read-only | The number of times a query has been sent from this interface. |
| C32 hpicfMldIfEntryStatGSQRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.9 | Counter32 | read-only | The number of times a group specific query has been received from this interface. |
| C32 hpicfMldIfEntryStatGSQTx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.10 | Counter32 | read-only | The number of times a group specific query has been sent from this interface. |
| C32 hpicfMldIfEntryStatMldV1ReportRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.11 | Counter32 | read-only | The number of times an MLD version 1 report has been received on this interface. |
| C32 hpicfMldIfEntryStatMldV2ReportRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.12 | Counter32 | read-only | The number of times an MLD version 2 report has been received on this interface. |
| C32 hpicfMldIfEntryStatMldV1LeaveRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.13 | Counter32 | read-only | The number of times an MLD version 1 leave has been received on this interface. |
| C32 hpicfMldIfEntryStatUnknownMldTypeRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.14 | Counter32 | read-only | The number of times an Mld packet of unknown type has been received on this interface. |
| C32 hpicfMldIfEntryStatUnknownPktRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.15 | Counter32 | read-only | The number of times a packet of unknown type has been sent to the MLD protocol on this device on this interface. |
| C32 hpicfMldIfEntryStatForwardToRoutersTx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.16 | Counter32 | read-only | The number of times a packet has been forwarded to routers on this interface. |
| C32 hpicfMldIfEntryStatForwardToAllPortsTx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.17 | Counter32 | read-only | The number of times a packet has been forwarded to all ports on this interface. |
| C32 hpicfMldIfEntryStatFastLeaves | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.18 | Counter32 | read-only | The number of times a fast leave has occurred on this interface. |
| C32 hpicfMldIfEntryStatForcedFastLeaves | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.19 | Counter32 | read-only | The number of times a forced fast leave has occurred on this interface. |
| C32 hpicfMldIfEntryStatJoinTimeouts | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.20 | Counter32 | read-only | The number of times a join has timeout out on this interface. |
| C32 hpicfMldIfEntryStatWrongVersionQueries | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.21 | Counter32 | read-only | The number of general queries received whose MLD version does not match the equivalent Interface Version. |
| C32 hpicfMldIfEntryLastMemberQueryCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.22 | Counter32 | read-only | Represents the number of group-specific and group-and-source-specific queries sent by the router before it assumes there are no local members. |
| C32 hpicfMldIfEntryStartupQueryCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.23 | Counter32 | read-only | Represents the number of Queries sent out on startup, separated by the Startup Query Interval (hpicfMldIfEntryStartupQueryInterval) |
| U32 hpicfMldIfEntryStartupQueryInterval | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.24 | Unsigned32 | read-only | Represents the interval between General Queries sent by a Querier on startup. |
| C32 hpicfMldIfEntryStatExcludeGroupJoinsCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.25 | Counter32 | read-only | Current number of groups on this interface which are in EXCLUDE mode. |
| C32 hpicfMldIfEntryStatIncludeGroupJoinsCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.26 | Counter32 | read-only | Current number of groups on this interface which are in INCLUDE mode. |
| C32 hpicfMldIfEntryStatFilteredExcludeGroupJoinsCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.27 | Counter32 | read-only | Current number of filtered groups on this interface which are in EXCLUDE mode. |
| C32 hpicfMldIfEntryStatFilteredIncludeGroupJoinsCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.28 | Counter32 | read-only | Current number of filtered groups on this interface which are in INCLUDE mode. |
| C32 hpicfMldIfEntryStatStandardExcludeGroupJoinsCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.29 | Counter32 | read-only | Current number of standard groups on this interface which are in EXCLUDE Mode. Traffic for these groups is flooded to the ports on the interface. These can come form joins on interfaces which do not have MLD snooping turned on. They can also come from interfaces which have MLD snooping on, but hardware resources have been exhausted for bridging traffic based on joins. |
| C32 hpicfMldIfEntryStatStandardIncludeGroupJoinsCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.30 | Counter32 | read-only | Current number of standard groups on this interface which are in INCLUDE Mode. Traffic for these groups is flooded to the ports on the interface. These can come form joins on interfaces which do not have MLD snooping turned on. They can also come from interfaces which have MLD snooping on, but hardware resources have been exhausted for bridging traffic based on joins. |
| C32 hpicfMldIfEntryStatV1QueryTx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.31 | Counter32 | read-only | The number of V1 Queries transmitted on this interface. |
| C32 hpicfMldIfEntryStatV1QueryRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.32 | Counter32 | read-only | The number of V1 Queries received on this interface. |
| C32 hpicfMldIfEntryStatV2QueryTx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.33 | Counter32 | read-only | The number of V2 Queries transmitted on this interface. |
| C32 hpicfMldIfEntryStatV2QueryRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.34 | Counter32 | read-only | The number of V2 Queries received on this interface. |
| C32 hpicfMldIfEntryStatGSSQTx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.35 | Counter32 | read-only | The number of Group Source Specific Queries transmitted on this interface. |
| C32 hpicfMldIfEntryStatGSSQRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.36 | Counter32 | read-only | The number of Group Source Specific Queries received on this interface |
| C32 hpicfMldIfEntryStatMalformedPktRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.37 | Counter32 | read-only | The number of malformed packets received on this interface. |
| C32 hpicfMldIfEntryStatBadCheckSumRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.38 | Counter32 | read-only | The number of bad checksum packets received on this interface. |
| C32 hpicfMldIfEntryStatMartianSourceRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.39 | Counter32 | read-only | The number of packets received on this interface from Martian source. Martian source are the packets with invalid source address, e.g. 255.255.255.255. |
| C32 hpicfMldIfEntryStatPacketsRxOnDisabled | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.40 | Counter32 | read-only | The number of MLD packets received on this interface when MLD is disabled. |
| T/F hpicfMldIfEntryStrictVersionMode | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.41 | TruthValue | read-write | When true, MLD packets whose version matches the protocol version configured on this interface will be processed. Other version MLD packets will be dropped. When false, all protocol version packets will be processed irrespective of the configured version. |
| C32 hpicfMldIfEntryStatMldV1ReportTx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.42 | Counter32 | read-only | The number of times an MLD version 1 report was transmitted on this interface. |
| C32 hpicfMldIfEntryStatMldV2ReportTx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.43 | Counter32 | read-only | The number of times an MLD version 2 report was transmitted on this interface. |
| HPI hpicfMldIfEntryState | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.44 | HpicfMldIfEntryState | read-only | Represents the MLD interface state. |
| C32 hpicfMldIfEntryStatV1GSQRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.45 | Counter32 | read-only | The number of V1 group specific queries received on this interface. |
| C32 hpicfMldIfEntryStatV1GSQTx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.46 | Counter32 | read-only | The number of V1 group specific queries transmitted by this interface. |
| C32 hpicfMldIfEntryStatV2GSQRx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.47 | Counter32 | read-only | The number of V2 group specific queries received on this interface. |
| C32 hpicfMldIfEntryStatV2GSQTx | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.48 | Counter32 | read-only | The number of V2 group specific queries transmitted by this interface. |
| TIK hpicfMldIfEntryStartupQueryExpiryTime | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.49 | TimeTicks | read-only | The minimum amount of time remaining before a multicast router decides that there is no longer another multicast router which should be the querier on startup on this interface. |
| U32 hpicfMldIfEntryOtherQuerierInterval | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.50 | Unsigned32 | read-only | The length of time that must pass before a multicast router decides that there is no longer another multicast router which should be the querier on this interface. |
| TIK hpicfMldIfEntryOtherQuerierExpiryTime | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.5.1.51 | TimeTicks | read-only | The minimum amount of time remaining before a multicast router decides that there is no longer another multicast router which should be the querier on this interface. |
| hpicfMldCacheTable | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6 | not-accessible | HP extensions to the MLD standard MIB table mldCacheTable. | |
| hpicfMldCacheEntry | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1 | not-accessible | HP extensions for an entry in the mldCacheTable. | |
| NUM hpicfMldCacheIfIndex | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.1 | InterfaceIndex | not-accessible | The internetwork-layer interface for which this entry contains information for an IPv6 multicast group address. |
| ADR hpicfMldCacheAddress | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.2 | InetAddressIPv6 | not-accessible | The IPv6 multicast group address for which this entry contains information. |
| T/F hpicfMldCacheSelf | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.3 | TruthValue | read-create | An indication of whether the local system is a member of this group address on this interface. |
| ADR hpicfMldCacheLastReporter | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.4 | InetAddressIPv6 | read-only | The IPv6 address of the source of the last membership report received for this IPv6 Multicast group address on this interface. If no membership report has been received, this object has the value 0::0. |
| TIK hpicfMldCacheUpTime | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.5 | TimeTicks | read-only | The time elapsed since this entry was created. |
| TIK hpicfMldCacheExpiryTime | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.6 | TimeTicks | read-only | The minimum amount of time remaining before this entry will be aged out. A value of 0 indicates that the entry is only present because mldCacheSelf is true and that if the router left the group, this entry would be aged out immediately. Note that some implementations may process Membership Reports from the local system in the same way as reports from other hosts, so a value of 0 is not required. |
| HPI hpicfMldGroupType | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.7 | HpicfMcastGroupTypeDefinition | read-only | See HpicfMldGroupTypeDefinition description. |
| POR hpicfJoinedPorts | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.8 | PortList | read-only | Logical ports with active MLD joins on them for this entry. For Filtered groups this will be the logical ports which have active joins. For standard and mini groups this will include all logical ports on the interface running MLD. |
| ROW hpicfMldCacheStatus | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.9 | RowStatus | read-create | The status of this row, by which new entries may be created, or existing entries deleted from this table. |
| INT hpicfMldCacheFilterMode | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.10 | INTEGER | read-only | The value indicates whether the group state is include(1) or exclude(2) |
| TIK hpicfMldCacheExcludeModeExpiryTimer | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.11 | TimeTicks | read-only | The time remaining before the group in EXCLUDE state expires and transitions to INCLUDE mode. |
| TIK hpicfMldCacheVersion1HostTimer | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.12 | TimeTicks | read-only | The time remaining until the local router will assume that there are no longer any MLD version 1 members on the IP subnet attached to this interface |
| C32 hpicfMldCacheSrcCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.6.1.13 | Counter32 | read-only | The number of sources either included or excluded for this group. If V1 host timer (hpicfMldCacheVersion1HostTimer) is active, this value will be zero. |
| hpicfMldPortConfigTable | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.7 | not-accessible | This table contains information about the MLD port configurations on this switch. | |
| hpicfMldPortConfigEntry | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.7.1 | not-accessible | The information associated with each MLD port configuration. | |
| NUM hpicfMldPortConfigEntryInterfaceIfIndex | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.7.1.1 | InterfaceIndex | not-accessible | The internetwork-layer interface value of the interface for which MLD is enabled. |
| I32 hpicfMldPortConfigEntryIndex | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.7.1.2 | Integer32 | not-accessible | The ifIndex value which uniquely identifies a row in the Interfaces Table for a port or trunk. |
| HPI hpicfMldPortConfigEntryPortModeFeature | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.7.1.3 | HpicfMldConfigPortModeType | read-write | The operational status of the MLD feature for this port or trunk. 1 implies that all IP Multicast traffic will be monitored on the port, 2 implies that IP Multicast traffic will be dropped on the port, and 3 implies that all IP Multicast traffic will be forwarded without the switch examining it. |
| T/F hpicfMldPortConfigEntryForcedLeaveFeature | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.7.1.4 | TruthValue | read-write | The operational status of the MLD feature for this port or trunk indicates whether any MLD Leaves received for an IPv6 Multicast group will cause the group to be deleted after the hpicfMLDConfigForcedLeaveInterval if no new MLD Reports are received for that group. Normal behavior is for a group issuing a Leave to be deleted after the Querier's Maximum Response time if no MLD Report is received. |
| T/F hpicfMldPortConfigEntryFastLeaveFeature | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.7.1.5 | TruthValue | read-write | The operational status of the MLD feature for this port or trunk indicates whether any MLD Leaves received for an IPv6 Multicast group will cause the group to be deleted immediately on single- connection ports. Normal behavior is for a group issuing a Leave to be deleted after the Querier's Maximum Response time if no MLD Report is received. |
| hpicfMldFilteredGroupPortCacheTable | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.8 | not-accessible | This table contains information about the MLD port configurations on this switch. | |
| hpicfMldFilteredGroupPortCacheEntry | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.8.1 | not-accessible | The information associated with each MLD port configuration. | |
| NUM hpicfMldFilteredGroupPortCacheIfIndex | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.8.1.1 | InterfaceIndex | not-accessible | The internetwork-layer interface value of the interface for which MLD is enabled and for which this filtered group exists. |
| ADR hpicfMldFilteredGroupPortCacheGroupAddress | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.8.1.2 | InetAddressIPv6 | not-accessible | The IPv6 multicast group address for which this entry contains information. |
| I32 hpicfMldFilteredGroupPortCachePortIndex | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.8.1.3 | Integer32 | not-accessible | The ifIndex value which uniquely identifies a row in the Interfaces Table for a port or trunk. |
| TIK hpicfMldFilteredGroupPortCacheExpiryTime | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.8.1.4 | TimeTicks | read-only | The minimum amount of time remaining before this entry will be aged out. |
| hpicfMldSrcListTable | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.9 | not-accessible | HP extensions to the Mgmd standard MIB table mgmdRouterSrcListTable for Ipv6 type. | |
| hpicfMldSrcListEntry | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.9.1 | not-accessible | HP extensions to the Mgmd standard MIB table mgmdRouterSrcListTable for Ipv6 type. | |
| NUM hpicfMldSrcListIfIndex | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.9.1.1 | InterfaceIndex | not-accessible | The internetwork-layer interface for which this entry contains information for an IPv6 multicast group address. |
| ADR hpicfMldSrcListAddress | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.9.1.2 | InetAddressIPv6 | not-accessible | The IPv6 multicast group address for which this entry contains information. |
| ADR hpicfMldSrcListHostAddress | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.9.1.3 | InetAddressIPv6 | not-accessible | The Host Address to which this entry corresponds. |
| POR hpicfMldSrcListPorts | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.9.1.4 | PortList | read-only | List of ports for which this entry is either excluded or included. |
| TIK hpicfMldSrcListExpiry | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.9.1.5 | TimeTicks | read-only | This value indicates the relevance of the SrcList entry, whereby a non-zero value indicates this is an INCLUDE state value, and a zero value indicates this to be an EXCLUDE state value. |
| TIK hpicfMldSrcListUpTime | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.9.1.6 | TimeTicks | read-only | The time elapsed since this entry was created. |
| HPI hpicfMldSrcListType | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.9.1.7 | HpicfMcastGroupTypeDefinition | read-only | See HpicfMldGroupTypeDefinition description. |
| hpicfMldPortSrcTable | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.10 | not-accessible | This table contains information about the MLD PortSrc configurations on this switch. | |
| hpicfMldPortSrcEntry | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.10.1 | not-accessible | HP extensions for an entry in the MLD PortSrc Table. | |
| NUM hpicfMldPortSrcIfIndex | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.10.1.1 | InterfaceIndex | not-accessible | The internetwork-layer interface for which this entry contains information for an IPv6 multicast group address. |
| ADR hpicfMldPortSrcAddress | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.10.1.2 | InetAddressIPv6 | not-accessible | The IPv6 multicast group address for which this entry contains information. |
| ADR hpicfMldPortSrcHostAddress | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.10.1.3 | InetAddressIPv6 | not-accessible | The Host Address to which this entry corresponds. |
| I32 hpicfMldPortSrcPortIndex | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.10.1.4 | Integer32 | not-accessible | The ifIndex value which uniquely identifies a row in the PortSrc Table for a port or trunk. |
| TIK hpicfMldPortSrcExpiry | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.10.1.5 | TimeTicks | read-only | This value indicates the relevance of the SrcList entry, whereby a non-zero value indicates this is an INCLUDE state value, and a zero value indicates this to be an EXCLUDE state value. |
| TIK hpicfMldPortSrcUpTime | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.10.1.6 | TimeTicks | read-only | The time elapsed since this entry was created. |
| INT hpicfMldPortSrcFilterMode | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.10.1.7 | INTEGER | read-only | The Value indicates whether the port state is include(1) or exclude(2). |
| I32 hpicfMldMcastExcludeGroupJoinsCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.11 | Integer32 | read-only | Number of multicast groups in Exclude mode. |
| I32 hpicfMldMcastIncludeGroupJoinsCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.12 | Integer32 | read-only | Number of multicast groups in Include mode. |
| POR hpicfMldMcastPortFastLearn | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.13 | PortList | read-write | List of ports on which the fast learn feature is enabled |
| hpicfMldGroupPortCacheTable | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14 | not-accessible | This table contains information about the MLD port configurations on this switch. | |
| hpicfMldGroupPortCacheEntry | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14.1 | not-accessible | The information associated with each MLD port configuration. | |
| NUM hpicfMldGroupPortCacheIfIndex | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14.1.1 | InterfaceIndex | not-accessible | The internetwork-layer interface value of the interface for which MLD is enabled and for which this group exists. |
| ADR hpicfMldGroupPortCacheGroupAddress | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14.1.2 | InetAddressIPv6 | not-accessible | The IPv6 multicast group address for which this entry contains information. |
| I32 hpicfMldGroupPortCachePortIndex | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14.1.3 | Integer32 | not-accessible | The ifIndex value which uniquely identifies a row in the Interfaces Table for a port or trunk. |
| TIK hpicfMldGroupPortCacheExpiryTime | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14.1.4 | TimeTicks | read-only | The minimum amount of time remaining before this entry will be aged out. |
| TIK hpicfMldGroupPortCacheUpTime | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14.1.5 | TimeTicks | read-only | The time elapsed since this entry was created. |
| TIK hpicfMldGroupPortCacheVersion1Timer | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14.1.6 | TimeTicks | read-only | The time remaining until the local router will assume that there are no longer any MLD version 1 members on this port. |
| TIK hpicfMldGroupPortCacheFilterTimer | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14.1.7 | TimeTicks | read-only | The time remaining before the port in EXCLUDE state expires and transitions to INCLUDE mode. |
| INT hpicfMldGroupPortCacheFilterMode | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14.1.8 | INTEGER | read-only | The Value indicates whether the port state is include(1) or exclude(2). |
| C32 hpicfMldGroupPortCacheExcludeSrcCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14.1.9 | Counter32 | read-only | Current number of sources excluded on this port. |
| C32 hpicfMldGroupPortCacheRequestedSrcCount | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.14.1.10 | Counter32 | read-only | Current number of sources requested on this port. |
| T/F hpicfMldReload | 1.3.6.1.4.1.11.2.14.11.5.1.48.1.1.15 | TruthValue | read-write | Setting this object to true will reset MLD on all interfaces, while setting this object to false does not have any impact. A get on this object will always return false. |
| hpicfMldConformance | 1.3.6.1.4.1.11.2.14.11.5.1.48.2 | |||
| hpicfMldGroups | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1 | |||
| hpicfMldBaseGroup | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.1 | A collection of objects to support basic MLD configuration information on HP routers. | ||
| hpicfMldIfGroup | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.2 | A collection of objects that extends objects defined in mldInterfaceTable and used to support management of interfaces with MLD enabled. | ||
| hpicfMldCacheGroup | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.3 | A collection of objects that extends objects defined in mldCacheTable and used to support management of interfaces with MLD enabled. | ||
| hpicfMldPortGroup | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.4 | A collection of objects that extends objects defined in mldInterfaceTable and used to support management of interfaces with MLD enabled. | ||
| hpicfMldFilteredGroupPortCacheGroup | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.5 | A collection of objects that extends objects defined in hpicfMldCacheTable which are of type filtered. These are used to support management of interfaces with MLD enabled. | ||
| hpicfMldBaseGroupV2 | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.6 | A collection of objects to support basic MLD configuration information on HP routers. | ||
| hpicfMldIfGroupV2 | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.7 | A collection of objects that extends objects defined in mldInterfaceTable and used to support management of interfaces with MLD enabled. | ||
| hpicfMldCacheGroupV2 | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.8 | A collection of objects that extends objects defined in mldCacheTable and used to support management of interfaces with MLD enabled. | ||
| hpicfMldSrcListGroup | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.9 | A collection of objects that extends objects defined in Mgmd standard MIB table mgmdRouterSrcListTable for Ipv6 type. | ||
| hpicfMldPortSrcGroup | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.10 | A collection of objects containing information about the MLD PortSrc configurations on this switch | ||
| hpicfMldGroupPortCacheGroup | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.11 | A collection of objects that extends objects defined in hpicfMldCacheTable. These are used to support management of interfaces with MLD enabled. | ||
| hpicfMldIfGroupV3 | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.12 | A collection of objects that extends objects defined in mldInterfaceTable and used to support management of interfaces with MLD enabled. | ||
| hpicfMldReloadModeGroup | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.1.13 | A collection of objects for MLD Reload mode. | ||
| hpicfMldCompliances | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.2 | |||
| hpicfMldMIBCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.2.1 | The compliance statement for HP routers running MLD and implementing the HP-ICF-MLD MIB. | ||
| hpicfMldMIBComplianceV2 | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.2.2 | The compliance statement for HP routers running MLD and implementing the HP-ICF-MLD MIB. | ||
| hpicfMldMIBComplianceV3 | 1.3.6.1.4.1.11.2.14.11.5.1.48.2.2.3 | The compliance statement for HP routers running MLD and implementing the HP-ICF-MLD MIB. |
RFC description
HP proprietary MIB for managing MLD (Multicast Listener Discovery) services with extensions to RFC 3019 standard.
Start monitoring HP ProCurve/Aruba switch (IPv6 MLD snooping/querier) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.