HIPATH-WIRELESS-HWC-MIB

All MIBs › HIPATH-WIRELESS-HWC-MIB

Organization: Chantry Networks Inc.

Last Updated: 2016-04-13

Category: Domain: Wireless, Vendor: Siemens, Wireless and WLAN

Description: Siemens HiPath Wireless Controller (HWC) MIB for centralized WLAN controller management and AP provisioning.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HIPATH-WIRELESS-HWC-MIB?

HIPATH-WIRELESS-HWC-MIB is a Siemens (Enterasys/Extreme-lineage) MIB for the HiPath Wireless Controller (HWC), the centralized appliance that manages a fleet of wireless access points in a HiPath WLAN deployment. It exposes access-controller-level configuration and management objects covering AP provisioning, controller-wide settings, and the management relationship between the HWC and its subordinate APs. Its monitoring value centers on the software/service status of the wireless management plane: verifying controller and AP association health helps detect an AP that has lost contact with its controller or a controller-side configuration problem affecting the whole WLAN. It serves as the parent/core MIB that HIPATH-WIRELESS-BRANCH-OFFICE-MIB and related branch modules build upon for remote-site scenarios. It is deployed at the central or regional site running the HiPath Wireless Controller appliance that manages access points across an enterprise campus or multi-site WLAN, typically after a HIPATH-WIRELESS-HWC-MIB download is used to load the module into the management station.

IPNetwork Monitor allows you to monitor SNMP objects defined in HIPATH-WIRELESS-HWC-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Siemens/Enterasys HiPath Wireless Controller (HWC)

Monitoring Examples

No sample object names were supplied in the source for this module, so specific OIDs cannot be cited, but an administrator would typically check the controller's AP association/provisioning table to confirm all managed access points are registered and reachable. An AP that drops out of the controller's managed list, or repeatedly fails provisioning, would indicate a lost management connection or a firmware/configuration mismatch between the AP and the HWC.

What Can Be Monitored

AP association/provisioning status
controller-level WLAN configuration state

Imported Objects

From HIPATH-WIRELESS-SMI

hiPathWirelessMgmt	OBJECT-IDENTITY
hiPathWirelessModules	OBJECT-IDENTITY

From IEEE802dot11-MIB

WEPKeytype

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From IPV6-TC

Ipv6Address

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using vnLocalClients OID:

Select a Siemens/Enterasys HiPath Wireless Controller (HWC) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type vnLocalClients into the Find box to locate it in the OID tree, then select it and click OK. It reports the number of locally associated clients to this controller that is considered to be their home controller in the mobility zone, which this controller is part of. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hiPathWirelessController	1.3.6.1.4.1.4329.15.3.2
systemObjects	1.3.6.1.4.1.4329.15.3.2.1
STR sysSoftwareVersion	1.3.6.1.4.1.4329.15.3.2.1.1	DisplayString	read-only	System software version.
LOG sysLogLevel	1.3.6.1.4.1.4329.15.3.2.1.2	LogEventSeverity	read-write	Sets the level of events which are written to the system log.
OCT sysSerialNo	1.3.6.1.4.1.4329.15.3.2.1.3	OCTET STRING	read-only	System serial number.
sysLogSupport	1.3.6.1.4.1.4329.15.3.2.1.4
INT hiPathWirelessAppLogFacility	1.3.6.1.4.1.4329.15.3.2.1.4.1	INTEGER	read-write	The application log facility level for syslog.
INT serviceLogFacility	1.3.6.1.4.1.4329.15.3.2.1.4.2	INTEGER	read-write	The service log facility level for syslog.
T/F includeAllServiceMessages	1.3.6.1.4.1.4329.15.3.2.1.4.3	TruthValue	read-write	Indicates if DHCP messages should also be forwarded to syslog.
sysLogServersTable	1.3.6.1.4.1.4329.15.3.2.1.4.4		not-accessible	Table of syslog servers to forward logging messages.
sysLogServersEntry	1.3.6.1.4.1.4329.15.3.2.1.4.4.1		not-accessible	Configuration information for an external syslog server.
I32 sysLogServerIndex	1.3.6.1.4.1.4329.15.3.2.1.4.4.1.1	Integer32	read-write	Table index for the syslog server.
T/F sysLogServerEnabled	1.3.6.1.4.1.4329.15.3.2.1.4.4.1.2	TruthValue	read-write	Indicates if messages are to be sent to the syslog server.
IP sysLogServerIP	1.3.6.1.4.1.4329.15.3.2.1.4.4.1.3	IpAddress	read-write	syslog server IP address.
I32 sysLogServerPort	1.3.6.1.4.1.4329.15.3.2.1.4.4.1.4	Integer32	read-write	syslog server port number.
ROW sysLogServerRowStatus	1.3.6.1.4.1.4329.15.3.2.1.4.4.1.5	RowStatus	read-write	RowStatus for operating on syslogServersTable.
STR sysCPUType	1.3.6.1.4.1.4329.15.3.2.1.5	DisplayString	read-only	Wireless controller's CPU type
apLogManagement	1.3.6.1.4.1.4329.15.3.2.1.6
T/F apLogCollectionEnable	1.3.6.1.4.1.4329.15.3.2.1.6.1	TruthValue	read-write	If this field is set to true, then the AP log collection feature is enabled.
I32 apLogFrequency	1.3.6.1.4.1.4329.15.3.2.1.6.2	Integer32	read-write	Number of log collections performed daily. The number must be one of the following 1, 2, 4, 6.
INT apLogDestination	1.3.6.1.4.1.4329.15.3.2.1.6.3	INTEGER	read-write	Destination where the log file will be stored. If the local flash is not mounted, then you can not select 1. 0 : local memory. 1 : flash. 2 : remote location.
INT apLogFTProtocol	1.3.6.1.4.1.4329.15.3.2.1.6.4	INTEGER	read-write	File transfer protocol. This field has meaning only when apLogDestination is set to remote(2). 0 : ftp. 1 : scp.
IP apLogServerIP	1.3.6.1.4.1.4329.15.3.2.1.6.5	IpAddress	read-write	The IP address of the remote server. This field has meaning only when apLogDestination is set to remote(2).
STR apLogUserId	1.3.6.1.4.1.4329.15.3.2.1.6.6	DisplayString	read-write	The user ID that is used for access to the remote server. This field has meaning only when apLogDestination is set to remote(2).
STR apLogPassword	1.3.6.1.4.1.4329.15.3.2.1.6.7	DisplayString	read-write	The user password that is used for access to the remote server. This field has meaning only when apLogDestination is set to remote(2). This field can only be viewed in SNMPv3 mode with privacy.
STR apLogDirectory	1.3.6.1.4.1.4329.15.3.2.1.6.8	DisplayString	read-write	The directory of the remote server. This field has meaning only when apLogDestination is set to remote(2).
apLogSelectedAPsTable	1.3.6.1.4.1.4329.15.3.2.1.6.9		not-accessible	Table containing a list of APs for which log collection is supported.
apLogSelectedAPsEntry	1.3.6.1.4.1.4329.15.3.2.1.6.9.1		not-accessible	Configuration information of an AP which supports the AP log feature.
OCT apSerialNo	1.3.6.1.4.1.4329.15.3.2.1.6.9.1.1	OCTET STRING	not-accessible	Table index for the apLogSelectedAPs. The AP's serial number serves as the index.
T/F select	1.3.6.1.4.1.4329.15.3.2.1.6.9.1.2	TruthValue	read-write	Indicates whether logs are collected from the AP.
INT apLogQuickSelectedOption	1.3.6.1.4.1.4329.15.3.2.1.6.10	INTEGER	read-write	This is a quick select option for the user to perform the AP's bulk selection. This field is write-only and read access returns unknown(0) value. 0 : unknown. 1 : add all APs. 2 : add all local APs. 3 : add all foreign APs. 4 : remove all APs. 5 : remove all local APs. 6 : remove all foreign APs.
apLogFileUtility	1.3.6.1.4.1.4329.15.3.2.1.7
U32 apLogFileUtilityLimit	1.3.6.1.4.1.4329.15.3.2.1.7.1	Unsigned32	read-only	The maximum number of AP log file copy requests that can be held in the apLogFileCopyTable. A value of 0 indicates no configured limit.
G32 apLogFileUtilityCurrent	1.3.6.1.4.1.4329.15.3.2.1.7.2	Gauge32	read-only	The number of AP log file copy requests currently in the apLogFileCopyTable.
apLogFileCopyTable	1.3.6.1.4.1.4329.15.3.2.1.7.5		not-accessible	List of AP log file copy requests.
apLogFileCopyEntry	1.3.6.1.4.1.4329.15.3.2.1.7.5.1		not-accessible	An entry describing the AP log file copy request.
U32 apLogFileCopyIndex	1.3.6.1.4.1.4329.15.3.2.1.7.5.1.1	Unsigned32	not-accessible	The index for this AP log file copy request.
INT apLogFileCopyDestination	1.3.6.1.4.1.4329.15.3.2.1.7.5.1.2	INTEGER	read-write	Destination where the log file will be copied. If the local flash is not mounted, then you can not select 1. 1 : copy the local AP log file to flash. 2 : copy the local AP log file to remote server.
INT apLogFileCopyProtocol	1.3.6.1.4.1.4329.15.3.2.1.7.5.1.3	INTEGER	read-write	File transfer protocol to be used to copy the log file. 0 : ftp. 1 : scp.
IP apLogFileCopyServerIP	1.3.6.1.4.1.4329.15.3.2.1.7.5.1.4	IpAddress	read-write	The IP address of the remote server.
STR apLogFileCopyUserID	1.3.6.1.4.1.4329.15.3.2.1.7.5.1.5	DisplayString	read-write	The user ID that is used for access to the remote server.
STR apLogFileCopyPassword	1.3.6.1.4.1.4329.15.3.2.1.7.5.1.6	DisplayString	read-write	The user password that is used for access to the remote server. This field can only be viewed in SNMPv3 mode with privacy.
STR apLogFileCopyServerDirectory	1.3.6.1.4.1.4329.15.3.2.1.7.5.1.7	DisplayString	read-write	The directory on the remote server.
INT apLogFileCopyOperation	1.3.6.1.4.1.4329.15.3.2.1.7.5.1.8	INTEGER	read-create	If this field is set to 1, then the controller will start to perform the copy action.
INT apLogFileCopyOperationStatus	1.3.6.1.4.1.4329.15.3.2.1.7.5.1.9	INTEGER	read-only	The operational state of the AP log file copy request. inactive - Indicates that the RowStatus of this conceptual row is not in the `active` state. pending - Indicates that the AP log file copy described by this row is ready to run and waiting in a queue. running - Indicates that the AP log file copy described by this row is running. success - Indicates that the AP log file copy described by this row has successfully run to completion. failure - Indicates that the AP log file copy described by this row has failed to run to completion.
ROW apLogFileCopyRowStatus	1.3.6.1.4.1.4329.15.3.2.1.7.5.1.10	RowStatus	read-create	Row status variable for row operations on the apLogFileCopyTable.
dnsObjects	1.3.6.1.4.1.4329.15.3.2.2
IP primaryDNS	1.3.6.1.4.1.4329.15.3.2.2.1	IpAddress	read-write	Primary DNS address configured in the Controller.
IP secondaryDNS	1.3.6.1.4.1.4329.15.3.2.2.2	IpAddress	read-write	Secondary DNS address configured in the Controller.
IP tertiaryDNS	1.3.6.1.4.1.4329.15.3.2.2.3	IpAddress	read-write	Third DNS address configured in the Controller.
mgmtPortObjects	1.3.6.1.4.1.4329.15.3.2.3
I32 mgmtPortIfIndex	1.3.6.1.4.1.4329.15.3.2.3.1	Integer32	read-only	ifIndex of the management port.
STR mgmtPortHostname	1.3.6.1.4.1.4329.15.3.2.3.2	DisplayString	read-write	Hostname of the management port.
STR mgmtPortDomain	1.3.6.1.4.1.4329.15.3.2.3.5	DisplayString	read-write	Domain of the management port.
physicalPortObjects	1.3.6.1.4.1.4329.15.3.2.4
I32 physicalPortCount	1.3.6.1.4.1.4329.15.3.2.4.1	Integer32	read-only	Number of rows in routerPortsTable.
physicalPortsTable	1.3.6.1.4.1.4329.15.3.2.4.2		not-accessible	Table of router ports on the controller.
physicalPortsEntry	1.3.6.1.4.1.4329.15.3.2.4.2.1		not-accessible	An entry in routerPortsTable.
T/F portMgmtTrafficEnable	1.3.6.1.4.1.4329.15.3.2.4.2.1.1	TruthValue	read-write	Determines whether controller management network traffic is allowed over this interface.
INT portDuplexMode	1.3.6.1.4.1.4329.15.3.2.4.2.1.2	INTEGER	read-write	Duplex mode for the esa ports.
INT portFunction	1.3.6.1.4.1.4329.15.3.2.4.2.1.3	INTEGER	read-write	Specifies the behavior of the EWC physical ports.
INT portEnabled	1.3.6.1.4.1.4329.15.3.2.4.2.1.4	INTEGER	read-write	If enabled, the interface administratively is enabled.
OCT portName	1.3.6.1.4.1.4329.15.3.2.4.2.1.5	OCTET STRING	read-only	A textual string containing information about the port.
IP portIpAddress	1.3.6.1.4.1.4329.15.3.2.4.2.1.6	IpAddress	read-write	The IP address of this port.
IP portMask	1.3.6.1.4.1.4329.15.3.2.4.2.1.7	IpAddress	read-write	The subnet mask associated with the IP address of this port.
MAC portMacAddress	1.3.6.1.4.1.4329.15.3.2.4.2.1.8	MacAddress	read-only	Port's MAC address.
I32 portVlanID	1.3.6.1.4.1.4329.15.3.2.4.2.1.9	Integer32	read-write	External VLAN tag for the physical port for trasmitted and received packets. Value ranges: (-1) it is not tagged, zero(0) means reserved, 1-4094 tag value.
T/F portDHCPEnable	1.3.6.1.4.1.4329.15.3.2.4.2.1.10	TruthValue	read-write	If enabled, the controller is configured as default DHCP server for AP.
STR portDHCPGateway	1.3.6.1.4.1.4329.15.3.2.4.2.1.11	DisplayString	read-write	Gateway address to be supplied to the wireless clients if controller is configured as default DHCP server for AP.
STR portDHCPDomain	1.3.6.1.4.1.4329.15.3.2.4.2.1.12	DisplayString	read-write	Domain name to be supplied to the wireless clients if controller is configured as default DHCP server for AP.
I32 portDHCPDefaultLease	1.3.6.1.4.1.4329.15.3.2.4.2.1.13	Integer32	read-write	Default DHCP lease time in seconds to be supplied to the wireless clients if controller is configured as default DHCP server for AP.
I32 portDHCPMaxLease	1.3.6.1.4.1.4329.15.3.2.4.2.1.14	Integer32	read-write	Maximum DHCP lease time in seconds to be supplied to the wireless clients if controller is configured as default DHCP server for AP.
STR portDHCPDnsServers	1.3.6.1.4.1.4329.15.3.2.4.2.1.15	DisplayString	read-write	List of DNSs to be supplied to the wireless clients if controller is configured as default DHCP server for AP.
STR portDHCPWins	1.3.6.1.4.1.4329.15.3.2.4.2.1.16	DisplayString	read-write	List of WINSs to be supplied to the wireless clients if controller is configured as default DHCP server for AP.
I32 physicalPortsInternalVlanID	1.3.6.1.4.1.4329.15.3.2.4.3	Integer32	read-write	Internal VLAN tag to be used for physical ports for which the exernal VLAN tag have not been configured. Value ranges: (-1) it is not tagged, zero(0) means reserved, 1-4094 tag value.
INT physicalFlash	1.3.6.1.4.1.4329.15.3.2.4.4	INTEGER	read-only	Flash drive status.
phyDHCPRangeTable	1.3.6.1.4.1.4329.15.3.2.4.5		not-accessible	phyDHCPRangeTable contains the IP address ranges that DHCP will serve to clients associated with physical ports.
phyDHCPRangeEntry	1.3.6.1.4.1.4329.15.3.2.4.5.1		not-accessible	Configuration information for a DHCP range.
I32 phyDHCPRangeIndex	1.3.6.1.4.1.4329.15.3.2.4.5.1.1	Integer32	read-write	Index for the DHCP row element.
IP phyDHCPRangeStart	1.3.6.1.4.1.4329.15.3.2.4.5.1.2	IpAddress	read-write	First IP address in the range.
IP phyDHCPRangeEnd	1.3.6.1.4.1.4329.15.3.2.4.5.1.3	IpAddress	read-write	Last IP address in the range.
INT phyDHCPRangeType	1.3.6.1.4.1.4329.15.3.2.4.5.1.4	INTEGER	read-write	Determines whether addresses in the specified range will be included, or excluded by the DHCP server.
ROW phyDHCPRangeStatus	1.3.6.1.4.1.4329.15.3.2.4.5.1.5	RowStatus	read-write	Row status variable for row operations on the phyDHCPRangeTable
layerTwoPortTable	1.3.6.1.4.1.4329.15.3.2.4.6		not-accessible	This table contains all layer two ports.
layerTwoPortEntry	1.3.6.1.4.1.4329.15.3.2.4.6.1		not-accessible	Entry for a layer two port.
STR layerTwoPortName	1.3.6.1.4.1.4329.15.3.2.4.6.1.1	DisplayString	read-only	Text string identifying the port within the controller.
INT layerTwoPortMgmtState	1.3.6.1.4.1.4329.15.3.2.4.6.1.2	INTEGER	read-write	This value indicates administrator state of the port.
MAC layerTwoPortMacAddress	1.3.6.1.4.1.4329.15.3.2.4.6.1.3	MacAddress	read-only	Port's MAC address.
INT jumboFrames	1.3.6.1.4.1.4329.15.3.2.4.7	INTEGER	read-write	Enables support for frames up to 1800 bytes long. jumboFrames support only applies to the controller and compatible APs.
vnManagerObjects	1.3.6.1.4.1.4329.15.3.2.5
INT vnRole	1.3.6.1.4.1.4329.15.3.2.5.1	INTEGER	read-write	Specifies the role of this EWC in inter-EWC mobility. None indicates that mobile units cannot roam to or from this EWC. In any EWC cluster, only one EWC should be specified as vnMgr, all others should be have vnRole = vnAgent.
I32 vnIfIndex	1.3.6.1.4.1.4329.15.3.2.5.2	Integer32	read-write	ifIndex of the physical port where inter-EWC tunnels terminate. This field has meaning if vnRole is not none(1)
I32 vnHeartbeatInterval	1.3.6.1.4.1.4329.15.3.2.5.3	Integer32	read-write	The time interval between inter-EWC polling messages. This field has meaning if vnRole is not none(1)
C32 vnLocalClientsEx	1.3.6.1.4.1.4329.15.3.2.5.4	Counter32	read-only	Number of locally associated clients to this controller that is considered to be their home controller in the mobility zone, which this controller is part of.
C32 vnForeignClients	1.3.6.1.4.1.4329.15.3.2.5.5	Counter32	read-only	Number of clients that have registered with another controller in the mobility zone, which this controller is part of, and currently have roamed to this controller.
C32 vnTotalClients	1.3.6.1.4.1.4329.15.3.2.5.6	Counter32	read-only	Number of local and foreign clients on this controller in the Mobility zone.
ntpObjects	1.3.6.1.4.1.4329.15.3.2.6
T/F ntpEnabled	1.3.6.1.4.1.4329.15.3.2.6.1	TruthValue	read-write	Enable or disables support for the Network Time Protocol (NTP).
STR ntpTimezone	1.3.6.1.4.1.4329.15.3.2.6.2	DisplayString	read-write	Specifies the time zone where this EWC resides.
STR ntpTimeServer1	1.3.6.1.4.1.4329.15.3.2.6.3	DisplayString	read-write	Primary NTP server.
STR ntpTimeServer2	1.3.6.1.4.1.4329.15.3.2.6.4	DisplayString	read-write	Secondary NTP server.
STR ntpTimeServer3	1.3.6.1.4.1.4329.15.3.2.6.5	DisplayString	read-write	Tertiary NTP server.
T/F ntpServerEnabled	1.3.6.1.4.1.4329.15.3.2.6.6	TruthValue	read-write	Enable or disables support for controller as NTP server.
controllerStats	1.3.6.1.4.1.4329.15.3.2.7
C64 tunnelsTxRxBytes	1.3.6.1.4.1.4329.15.3.2.7.1	Counter64	read-only	Sum of transmitted and received bytes over all existing tunnels.
I32 tunnelCount	1.3.6.1.4.1.4329.15.3.2.7.6	Integer32	read-only	Number of connections to other WirelessController controllers.
tunnelStatsTable	1.3.6.1.4.1.4329.15.3.2.7.7		not-accessible	tunnelStatsTable contains a list of the IP tunnels connected to this EWC for use in inter-EWC mobility.
tunnelStatsEntry	1.3.6.1.4.1.4329.15.3.2.7.7.1		not-accessible	Statistics for a mobility tunnel.
IP tunnelStartIP	1.3.6.1.4.1.4329.15.3.2.7.7.1.1	IpAddress	read-write	IP address for the start of the tunnel.
OCT tunnelStartHWC	1.3.6.1.4.1.4329.15.3.2.7.7.1.2	OCTET STRING	read-write	Name of the access controller for the start of the tunnel.
IP tunnelEndIP	1.3.6.1.4.1.4329.15.3.2.7.7.1.3	IpAddress	read-write	IP address for the end of the tunnel.
OCT tunnelEndHWC	1.3.6.1.4.1.4329.15.3.2.7.7.1.4	OCTET STRING	read-write	Name of the access controller for the end of the tunnel.
INT tunnelStatus	1.3.6.1.4.1.4329.15.3.2.7.7.1.5	INTEGER	read-write	Indicates if the mobility tunnel is up or down.
C32 tunnelStatsTxBytes	1.3.6.1.4.1.4329.15.3.2.7.7.1.6	Counter32	read-only	Number of bytes have been transmitted from the controller at the start of the tunnel to the controller on the other end of the tunnel.
C32 tunnelStatsRxBytes	1.3.6.1.4.1.4329.15.3.2.7.7.1.7	Counter32	read-only	Number of bytes have been received by the controller at the end of the tunnel from the controller at the start of the tunnel.
C32 tunnelStatsTxRxBytes	1.3.6.1.4.1.4329.15.3.2.7.7.1.8	Counter32	read-only	Sum of transmitted and received bytes over this tunnel.
INT clearAccessRejectMsg	1.3.6.1.4.1.4329.15.3.2.7.8	INTEGER	read-write	Set this OID to one to erase the contents of the accessRejectMessage table. The OID always returns 0 when read.
accessRejectMsgTable	1.3.6.1.4.1.4329.15.3.2.7.9		not-accessible	This table lists each of the reply messages returned in RADIUS Access-Reject messages and for each reply message, a count of the number of times it has been received.
accessRejectMsgEntry	1.3.6.1.4.1.4329.15.3.2.7.9.1		not-accessible	One entry consisting of a unique Access-Reject Reply-Message (accessRejectReplyMessage) and count of this message.
I32 armIndex	1.3.6.1.4.1.4329.15.3.2.7.9.1.1	Integer32	not-accessible	A number uniquely identifying each conceptual row in the accessRejectMsgTable.
C64 armCount	1.3.6.1.4.1.4329.15.3.2.7.9.1.2	Counter64	read-only	Count of the number of times the controller has received an Access-Reject response from a RADIUS server that contained the associated armReplyMessage.
STR armReplyMessage	1.3.6.1.4.1.4329.15.3.2.7.9.1.3	DisplayString	read-only	A reply message attribute received by the controller from a RADIUS server in an Access-Reject message.
availability	1.3.6.1.4.1.4329.15.3.2.8
INT availabilityStatus	1.3.6.1.4.1.4329.15.3.2.8.1	INTEGER	read-write	This field can be used to enable or disable availability. If it is set to paired(1), then availability is enabled on this controller, otherwise it is considered that the controller operates in stand-alone mode. All other availability fields have no meaning if this field is set to standalone(0).
IP pairIPAddress	1.3.6.1.4.1.4329.15.3.2.8.2	IpAddress	read-write	IP address of paired controller in availability pairing mode.
INT hwcAvailabilityRank	1.3.6.1.4.1.4329.15.3.2.8.3	INTEGER	read-write	Rank of controller in Availability pairing mode. This is legacy field and applies to releases before 5.x and in current releases it is used for reporting only.
INT fastFailover	1.3.6.1.4.1.4329.15.3.2.8.4	INTEGER	read-write	Enables or disables fast failover when controller operates in Availability pairing mode.
U32 detectLinkFailure	1.3.6.1.4.1.4329.15.3.2.8.5	Unsigned32	read-write	Time to detect link failure between two controllers in availability pairing. The value can be set to values between 2-30 seconds
T/F synchronizeSystemConfig	1.3.6.1.4.1.4329.15.3.2.8.6	TruthValue	read-write	If this flag is set to enabled then system configuration is synchronized between paired controllers operating in Availabilty pairing mode.
T/F synchronizeGuestPort	1.3.6.1.4.1.4329.15.3.2.8.7	TruthValue	read-write	If this flag is set to enabled then Guest Portal user accounts are synchronized between paired controllers operating in Availabilty pairing mode.
secureConnection	1.3.6.1.4.1.4329.15.3.2.9
INT weakCipherEnable	1.3.6.1.4.1.4329.15.3.2.9.1	INTEGER	read-write	By default usage of weak cipher is enabled on EWC. Weak cipher can be disabled using this field.
dashboard	1.3.6.1.4.1.4329.15.3.2.10
licensingInformation	1.3.6.1.4.1.4329.15.3.2.10.1
STR licenseRegulatoryDomain	1.3.6.1.4.1.4329.15.3.2.10.1.1	DisplayString	read-only	Regulatory domain that this wireless controller system has been licensed for to operate.
INT licenseType	1.3.6.1.4.1.4329.15.3.2.10.1.2	INTEGER	read-only	Type of license for the controller. Temporary lincese allows controller to operate within defined number of days after which a permanent license is required for the operation of the controller system.
U32 licenseDaysRemaining	1.3.6.1.4.1.4329.15.3.2.10.1.3	Unsigned32	read-only	Number of days is left for the temporary license to expire. This value has meaning if the license type is temporary(1).
U32 licenseAvailableAP	1.3.6.1.4.1.4329.15.3.2.10.1.4	Unsigned32	read-only	If licenseMode is standAlone, this is the maximum number of APs that can be active on the controller without violating the licensing agreement. If licenseMode is availabilityPaired, this is the maximum number of APs that can be active on both members of the availability pair without violating the licensing agreement.
U32 licenseInServiceRadarAP	1.3.6.1.4.1.4329.15.3.2.10.1.5	Unsigned32	read-only	If licenseMode is standalone this is the maximum number of APs that can be active on this controller and can operate as Guardians or in-service Radar APs without violating the licensing agreement. If licenseMode is availabilityPaired, this is the maximum number of APs that can be active on both members of the availability pair and can operate as Guardians or in-service Radar APs without violating the licensing agreement.
INT licenseMode	1.3.6.1.4.1.4329.15.3.2.10.1.6	INTEGER	read-only	License mode determines how to interpret the license capacity OIDs. licenseMode is standalone if the controller is not part of an availability pair. licenseMode is availabilityPaired if the controller is part of an availability pair.
U32 licenseLocalAP	1.3.6.1.4.1.4329.15.3.2.10.1.7	Unsigned32	read-only	The total number of AP capacity licenses installed on this controller.
U32 licenseForeignAP	1.3.6.1.4.1.4329.15.3.2.10.1.8	Unsigned32	read-only	The total number of AP capacity licenses installed on this controller's availability partner.
U32 licenseLocalRadarAP	1.3.6.1.4.1.4329.15.3.2.10.1.9	Unsigned32	read-only	The total number of AP Radar capacity licenses installed on this controller.
U32 licenseForeignRadarAP	1.3.6.1.4.1.4329.15.3.2.10.1.10	Unsigned32	read-only	The total number of AP Radar capacity licenses installed on this controller's availability partner.
stationsByProtocol	1.3.6.1.4.1.4329.15.3.2.10.2
U32 stationsByProtocolA	1.3.6.1.4.1.4329.15.3.2.10.2.1	Unsigned32	read-only	Number of stations using 802.11a mode to access the network.
U32 stationsByProtocolB	1.3.6.1.4.1.4329.15.3.2.10.2.2	Unsigned32	read-only	Number of stations using 802.11b mode to access the network.
U32 stationsByProtocolG	1.3.6.1.4.1.4329.15.3.2.10.2.3	Unsigned32	read-only	Number of stations using 802.11b mode to access the network.
U32 stationsByProtocolN24	1.3.6.1.4.1.4329.15.3.2.10.2.4	Unsigned32	read-only	Number of stations using 802.11n mode with frequency of 2.4Gig to access the network.
U32 stationsByProtocolN5	1.3.6.1.4.1.4329.15.3.2.10.2.5	Unsigned32	read-only	Number of stations using 802.11n mode with frequency of 5Gig to access the network.
U32 stationsByProtocolUnavailable	1.3.6.1.4.1.4329.15.3.2.10.2.6	Unsigned32	read-only	The total number of stations with sessions on this controller for which the 802.11 protocol type (a, b, g, n, ac) for which the protocol could not be determined.
U32 stationsByProtocolError	1.3.6.1.4.1.4329.15.3.2.10.2.7	Unsigned32	read-only	The total number of stations with sessions on this controller for which an AP reported an invalid (out of range) value as the station's 802.11 protocol type.
U32 stationsByProtocolAC	1.3.6.1.4.1.4329.15.3.2.10.2.8	Unsigned32	read-only	Number of stations using 802.11ac mode to access the network.
apByChannelTable	1.3.6.1.4.1.4329.15.3.2.10.3		not-accessible	List of aggregated access points that are operating on a specific wireless channels.
apByChannelEntry	1.3.6.1.4.1.4329.15.3.2.10.3.1		not-accessible	An entry in this table for one wireless channel and aggregated access point on that channel.
U32 apByChannelNumber	1.3.6.1.4.1.4329.15.3.2.10.3.1.1	Unsigned32	not-accessible	The channel on which a set of access points are presently operating. If this number is 0, this means the AP is in Guardian mode or the AP's radios are turned off.
U32 apByChannelAPs	1.3.6.1.4.1.4329.15.3.2.10.3.1.2	Unsigned32	read-only	Total number of the access point on the channel that this row is indexed on.
virtualNetworks	1.3.6.1.4.1.4329.15.3.3
vnsConfigObjects	1.3.6.1.4.1.4329.15.3.3.1
I32 vnsCount	1.3.6.1.4.1.4329.15.3.3.1.1	Integer32	read-only	Number of VNSes defined in vnsConfigTable.
vnsConfigTable	1.3.6.1.4.1.4329.15.3.3.1.2		not-accessible	Contains definitions of the Virtual Network Segments defined on this WirelessController.
vnsConfigEntry	1.3.6.1.4.1.4329.15.3.3.1.2.1		not-accessible	Configuration elements for a specific Virtual Network Segment.
STR vnsDescription	1.3.6.1.4.1.4329.15.3.3.1.2.1.1	DisplayString	read-write	Textual description of the VNS.
INT vnsAssignmentMode	1.3.6.1.4.1.4329.15.3.3.1.2.1.2	INTEGER	read-write	Determines the method by which mobile units are assigned an address within this VNS. If vnsAssignmentMode = ssid, any client with an SSID matching the VNS will be assigned an address from this VNS. If vnsAssignmentMode == aaa, then address assignment is not completed until after the user is authenticated.
I32 vnsMUSessionTimeout	1.3.6.1.4.1.4329.15.3.3.1.2.1.3	Integer32	read-write	Client session idle time out, in seconds.
T/F vnsAllowMulticast	1.3.6.1.4.1.4329.15.3.3.1.2.1.4	TruthValue	read-write	When true, allows IP multicast packets to be broadcast to the clients on this VNS.
STR vnsSSID	1.3.6.1.4.1.4329.15.3.3.1.2.1.5	DisplayString	read-write	Service Set Identifier (i.e. Network Name) that will be configured on the AccessPoints associated with this VNS.
STR vnsDomain	1.3.6.1.4.1.4329.15.3.3.1.2.1.6	DisplayString	read-write	Domain name to be supplied to the wireless clients if internal DHCP address assignment.
STR vnsDNSServers	1.3.6.1.4.1.4329.15.3.3.1.2.1.7	DisplayString	read-write	List of DNSs to be supplied to the wireless clients if internal DHCP address assignment.
STR vnsWINSServers	1.3.6.1.4.1.4329.15.3.3.1.2.1.8	DisplayString	read-write	List of WINSs to be supplied to the wireless clients if internal DHCP address assignment.
INT vnsAuthModel	1.3.6.1.4.1.4329.15.3.3.1.2.1.9	INTEGER	read-write	vnsAuthModel specifies the authentication method used for clients in the VNS. None indicates that the VNS is open, and no authentication is required. vnsAuthModel=captivePortal may only be specified for a VNS with vnsAssignmentMode=ssid. Likewise, vnsAuthModel=dot1X may only be specified for a VNS with vnsAssignmentMode=aaa.
I32 vnsParentIfIndex	1.3.6.1.4.1.4329.15.3.3.1.2.1.10	Integer32	read-write	Specifies the ifIndex of the parent VNS, if this VNS is a child. If this is a top level VNS, vnsParentIfIndex will return null or 0.
T/F vnsMgmtTrafficEnable	1.3.6.1.4.1.4329.15.3.3.1.2.1.11	TruthValue	read-write	Specifies whether clients in the VNS have access to EWC management elements.
INT vnsUseDHCPRelay	1.3.6.1.4.1.4329.15.3.3.1.2.1.12	INTEGER	read-write	This variable indicates what type of DHCP is used for the VNS. none(0): No DHCP server on the VNS. dhcpRelay(1): Uses DHCP relay to reach the DHCP server. localDhcp(2): Uses local DHCP server on the controler.
T/F vns3rdPartyAP	1.3.6.1.4.1.4329.15.3.3.1.2.1.13	TruthValue	read-write	When true, specifies that the VNS contains 3rd party access points. Only one such VNS may be defined for a WirelessController.
ROW vnsStatus	1.3.6.1.4.1.4329.15.3.3.1.2.1.14	RowStatus	read-write	RowStatus variable for performing row operations on vnsConfigTable.
INT vnsMode	1.3.6.1.4.1.4329.15.3.3.1.2.1.15	INTEGER	read-write	Type of traffic for this VNS. routed(1): The traffic is routed at the controller. bridgeAtController(2): Traffic is bridged at controller. bridgeAtAP(3): Traffic is bridged at Access Points. wds(4): Wireless Distributed System (WDS) type of VNS. If VNS is type of wds(4), then only vnsSupressSSID, vnsDescription and vnsSSID has meaning.
I32 vnsVlanID	1.3.6.1.4.1.4329.15.3.3.1.2.1.16	Integer32	read-write	VLAN tag for the packets trasmitted to/from of the VNS. This value has meaning if vnsMode is bridgeAtController(2) or bridgeAtAP(3). If vnsMode = bridgeAtController(2), tagging is done at controller. If vnsMode = bridgeAtAP(3), tagging is done at Access Point. Value ranges: (-1) it is not tagged, zero(0) means reserved, 1-4094 tag value.
OCT vnsInterfaceName	1.3.6.1.4.1.4329.15.3.3.1.2.1.17	OCTET STRING	read-write	Physical interface to be used in the controller for trasmitting/receiving packets for the VNS. This value has meaning if vnsMode is bridgeAtController(2).
IP vnsMgmIpAddress	1.3.6.1.4.1.4329.15.3.3.1.2.1.18	IpAddress	read-write	IP address of the management port associated to this VNS. This value has meaning if vnsMode is bridgeAtController(2).
T/F vnsSuppressSSID	1.3.6.1.4.1.4329.15.3.3.1.2.1.19	TruthValue	read-write	If set to true, this prevents this SSID from appearing in the beacon message.
T/F vnsEnable11hSupport	1.3.6.1.4.1.4329.15.3.3.1.2.1.20	TruthValue	read-write	If true, enables 802.11h support.
T/F vnsApplyPowerBackOff	1.3.6.1.4.1.4329.15.3.3.1.2.1.21	TruthValue	read-write	Indicates whether the AP will direct 802.11h-enabled clients to apply the same power back-off setting that the AP is using
T/F vnsProcessClientIEReq	1.3.6.1.4.1.4329.15.3.3.1.2.1.22	TruthValue	read-write	If true, enables support for 802.11d client information request.
T/F vnsDLSSupportEnable	1.3.6.1.4.1.4329.15.3.3.1.2.1.23	TruthValue	read-write	If true, enables support for DLS Support. This value has meaning only if vnsUseDHCPRelay is selected as localDhcp(2) and vnsMode is select as either routed(1) or bridgeAtController(2).
STR vnsDLSAddress	1.3.6.1.4.1.4329.15.3.3.1.2.1.24	DisplayString	read-write	DNS IP Address for DLS associated to this VNS. It could be IP address or Name
I32 vnsDLSPort	1.3.6.1.4.1.4329.15.3.3.1.2.1.25	Integer32	read-write	DNS Port for DLS associated to this VNS.
STR vnsRateControlProfile	1.3.6.1.4.1.4329.15.3.3.1.2.1.26	DisplayString	read-write	The Rate Control Profile that is referenced by this VNS.
T/F vnsSessionAvailabilityEnable	1.3.6.1.4.1.4329.15.3.3.1.2.1.27	TruthValue	read-write	To indicate if Session Availability feature is enabled.
INT vnsEnabled	1.3.6.1.4.1.4329.15.3.3.1.2.1.28	INTEGER	read-write	VNS status of being enabled or disabled.
INT vnsStrictSubnetAdherence	1.3.6.1.4.1.4329.15.3.3.1.2.1.29	INTEGER	read-write	Subnet adherence verification status for the VNS. Controller only learns devices whose address is within range of VNS segment definition. Disabling this field causes to not enforce validation. Doing so, may expose the controller to in-advertent Learning DoS attacks.
INT vnsSLPEnabled	1.3.6.1.4.1.4329.15.3.3.1.2.1.30	INTEGER	read-write	Status of SLP flag on Bridge at Controller type VNS. This field does not have any meaning for other types of VNS.
U32 vnsConfigWLANID	1.3.6.1.4.1.4329.15.3.3.1.2.1.31	Unsigned32	read-write	Creation of VNS requires existing of a free WLAN. One WLAN can only be used in one VNS only. This ID identifies the WLAN that is used for creation of VNS that is identified by this row.
vnsDHCPRangeTable	1.3.6.1.4.1.4329.15.3.3.1.3		not-accessible	vnsDHCPRangeTable contains the IP address ranges that DHCP will serve to clients associated with this VNS.
vnsDHCPRangeEntry	1.3.6.1.4.1.4329.15.3.3.1.3.1		not-accessible	Configuration information for a DHCP range.
I32 vnsDHCPRangeIndex	1.3.6.1.4.1.4329.15.3.3.1.3.1.1	Integer32	read-write	Index for the DHCP row element.
IP vnsDHCPRangeStart	1.3.6.1.4.1.4329.15.3.3.1.3.1.2	IpAddress	read-write	First IP address in the range.
IP vnsDHCPRangeEnd	1.3.6.1.4.1.4329.15.3.3.1.3.1.3	IpAddress	read-write	Last IP address in the range.
INT vnsDHCPRangeType	1.3.6.1.4.1.4329.15.3.3.1.3.1.4	INTEGER	read-write	Determines whether addresses in the specified range will be included, or excluded by the DHCP server.
ROW vnsDHCPRangeStatus	1.3.6.1.4.1.4329.15.3.3.1.3.1.5	RowStatus	read-write	Row status variable for row operations on the vnsDHCPRangeTable
vnsCaptivePortalTable	1.3.6.1.4.1.4329.15.3.3.1.4		not-accessible	Details of the Captive Portal login page for VNSes that have vnsAssignment=ssid and vnsAuthModel=captivePortal.
vnsCaptivePortalEntry	1.3.6.1.4.1.4329.15.3.3.1.4.1		not-accessible	Captive Portal Information for the VNS.
STR cpURL	1.3.6.1.4.1.4329.15.3.3.1.4.1.1	DisplayString	read-write	Redirect URL of the Captive Portal login page.
STR cpLoginLabel	1.3.6.1.4.1.4329.15.3.3.1.4.1.2	DisplayString	read-write	Label that appears in front of the login field on the Captive Portal login page.
STR cpPasswordLabel	1.3.6.1.4.1.4329.15.3.3.1.4.1.3	DisplayString	read-write	Label that appears in front of the password field on the Captive Portal login page.
STR cpHeaderURL	1.3.6.1.4.1.4329.15.3.3.1.4.1.4	DisplayString	read-write	URL of the Captive Portal header.
STR cpFooterURL	1.3.6.1.4.1.4329.15.3.3.1.4.1.5	DisplayString	read-write	URL of the Captive Portal footer.
STR cpMessage	1.3.6.1.4.1.4329.15.3.3.1.4.1.6	DisplayString	read-write	A welcome message, or set of instructions that is to appear on the Captive Portal login page.
STR cpReplaceGatewayWithFQDN	1.3.6.1.4.1.4329.15.3.3.1.4.1.7	DisplayString	read-write	Fully Qualified Domain Name (FQDN) to be used as the gateway IP address.
STR cpDefaultRedirectionURL	1.3.6.1.4.1.4329.15.3.3.1.4.1.8	DisplayString	read-write	Default Redirect URL of the Captive Portal login page.
IP cpConnectionIP	1.3.6.1.4.1.4329.15.3.3.1.4.1.9	IpAddress	read-write	IP address of the Controller interface for Captive Portal.
I32 cpConnectionPort	1.3.6.1.4.1.4329.15.3.3.1.4.1.10	Integer32	read-write	Port number on the cpConnectionIP interface.
OCT cpSharedSecret	1.3.6.1.4.1.4329.15.3.3.1.4.1.11	OCTET STRING	read-write	Secret Key to be used to encrypt the information passed between the Controller and the external web server. It is the password common to both Controller and the external web server.
INT cpLogOff	1.3.6.1.4.1.4329.15.3.3.1.4.1.12	INTEGER	read-write	Toggles the display of logoff popup screen, allowing users to control their logoff.
INT cpStatusCheck	1.3.6.1.4.1.4329.15.3.3.1.4.1.13	INTEGER	read-write	Toggles the display of popup window with session statistics for users to monitor their usage and time left in session.
INT cpType	1.3.6.1.4.1.4329.15.3.3.1.4.1.14	INTEGER	read-write	Type of captive portal is enabled for the selected VNS. none(1) = no captive portal configured or type is unknown. internal(2) = internal captive portal. external(4) = external captive portal. guestPortal (5) = open host captive portal.
vnsRadiusServerTable	1.3.6.1.4.1.4329.15.3.3.1.5		not-accessible	List of RADIUS servers to be utilized for authentication in the VNS.
vnsRadiusServerEntry	1.3.6.1.4.1.4329.15.3.3.1.5.1		not-accessible	Configuration information for a RADIUS server.
STR vnsRadiusServerName	1.3.6.1.4.1.4329.15.3.3.1.5.1.1	DisplayString	read-write	Name of the RADIUS server.
I32 vnsRadiusServerPort	1.3.6.1.4.1.4329.15.3.3.1.5.1.2	Integer32	read-write	Port number for the RADIUS server.
I32 vnsRadiusServerRetries	1.3.6.1.4.1.4329.15.3.3.1.5.1.3	Integer32	read-write	Number of retries for a RADIUS authentication request.
I32 vnsRadiusServerTimeout	1.3.6.1.4.1.4329.15.3.3.1.5.1.4	Integer32	read-write	Delay between requests.
STR vnsRadiusServerSharedSecret	1.3.6.1.4.1.4329.15.3.3.1.5.1.5	DisplayString	read-write	Shared secret to be used between the NAS and RADIUS server.
STR vnsRadiusServerNASIdentifier	1.3.6.1.4.1.4329.15.3.3.1.5.1.6	DisplayString	read-write	NAS identifier to be included in RADIUS request.
INT vnsRadiusServerAuthType	1.3.6.1.4.1.4329.15.3.3.1.5.1.7	INTEGER	read-write	Challenge mechanism for the request.
ROW vnsRadiusServerRowStatus	1.3.6.1.4.1.4329.15.3.3.1.5.1.8	RowStatus	read-write	RowStatus value for manipulating vnsRADIUSServerTable.
IP vnsRadiusServerNasAddress	1.3.6.1.4.1.4329.15.3.3.1.5.1.9	IpAddress	read-write	NAS address to be included in RADIUS request.
vnsFilterIDTable	1.3.6.1.4.1.4329.15.3.3.1.6		not-accessible	Table of names filters for a VNS.
vnsFilterIDEntry	1.3.6.1.4.1.4329.15.3.3.1.6.1		not-accessible	Name of a specific filter in the VNS.
STR vnsFilterID	1.3.6.1.4.1.4329.15.3.3.1.6.1.1	DisplayString	read-write	Filter names.
ROW vnsFilterIDStatus	1.3.6.1.4.1.4329.15.3.3.1.6.1.2	RowStatus	read-write	RowStatus for operating on vnsFilterIDTable.
vnsFilterRuleTable	1.3.6.1.4.1.4329.15.3.3.1.7		not-accessible	Table containing specific filters for a named filter.
vnsFilterRuleEntry	1.3.6.1.4.1.4329.15.3.3.1.7.1		not-accessible	Filter elements for an individual VNS filter.
I32 vnsFilterRuleOrder	1.3.6.1.4.1.4329.15.3.3.1.7.1.1	Integer32	read-write	Position of the filter in the filter list.
INT vnsFilterRuleDirection	1.3.6.1.4.1.4329.15.3.3.1.7.1.2	INTEGER	read-write	Traffic direction defined by the rule.
INT vnsFilterRuleAction	1.3.6.1.4.1.4329.15.3.3.1.7.1.3	INTEGER	read-write	Allow or deny traffic for the filter.
IP vnsFilterRuleIPAddress	1.3.6.1.4.1.4329.15.3.3.1.7.1.4	IpAddress	read-write	IP address to apply the filter.
I32 vnsFilterRulePortLow	1.3.6.1.4.1.4329.15.3.3.1.7.1.5	Integer32	read-write	Low port number for the filter.
I32 vnsFilterRulePortHigh	1.3.6.1.4.1.4329.15.3.3.1.7.1.6	Integer32	read-write	High port number for the filter.
INT vnsFilterRuleProtocol	1.3.6.1.4.1.4329.15.3.3.1.7.1.7	INTEGER	read-write	Specific protocol to filter.
INT vnsFilterRuleEtherType	1.3.6.1.4.1.4329.15.3.3.1.7.1.8	INTEGER	read-write	Specific ethertype to filter.
ROW vnsFilterRuleStatus	1.3.6.1.4.1.4329.15.3.3.1.7.1.9	RowStatus	read-write	RowStatus value for the vnsFilterRuleTable.
vnsPrivacyTable	1.3.6.1.4.1.4329.15.3.3.1.8		not-accessible	Table of privacy settings for the VNS.
vnsPrivacyEntry	1.3.6.1.4.1.4329.15.3.3.1.8.1		not-accessible	Configuration values for a specific privacy setting.
INT vnsPrivWEPKeyType	1.3.6.1.4.1.4329.15.3.3.1.8.1.1	INTEGER	read-write	Type of key in use. none(1) = not cofigured, wepstatic(2) = static WEP, wpapsk(3) = WPA Pre-Shared Key, dynamic(4) = dynamically assigned, wpa(5) = WPA.
I32 vnsPrivDynamicRekeyFrequency	1.3.6.1.4.1.4329.15.3.3.1.8.1.2	Integer32	read-write	Dynamic WEP re-keying frequency, in seconds. Setting this value to 0 disables rekeying. This value is only meaningful if vnsPrivWEPKeyType = wpapsk(3). For any other values of vnsPrivWEPKeyType, reading or setting this value will return an unsuccessful status and will return a value of null or zero.
I32 vnsPrivWEPKeyLength	1.3.6.1.4.1.4329.15.3.3.1.8.1.3	Integer32	read-write	WEP key length, 64, 128, or 152 bits. If vnsPrivWEPKeyType is none, reading or setting this value will return an unsuccessful status and will return a value of null or zero.
T/F vnsPrivWPA1Enabled	1.3.6.1.4.1.4329.15.3.3.1.8.1.4	TruthValue	read-write	Enables WPA.1 (Wi-Fi Protected Access).
T/F vnsPrivUseSharedKey	1.3.6.1.4.1.4329.15.3.3.1.8.1.5	TruthValue	read-write	Enables the use of WPA shared key for this VNS.
STR vnsPrivWPASharedKey	1.3.6.1.4.1.4329.15.3.3.1.8.1.6	DisplayString	read-write	The value of the WPA shared key for this VNS. This value is logically WRITE ONLY. Attempts to read this value shall return unsuccessful status and values of null or zero.
T/F vnsPrivWPA2Enabled	1.3.6.1.4.1.4329.15.3.3.1.8.1.7	TruthValue	read-write	When true, WPA v.2 support is enabled.
vnsWEPKeyTable	1.3.6.1.4.1.4329.15.3.3.1.9		not-accessible	Table of WEP key entries for a static WEP definition.
vnsWEPKeyEntry	1.3.6.1.4.1.4329.15.3.3.1.9.1		not-accessible	WEP key for a single entry in the table.
I32 vnsWEPKeyIndex	1.3.6.1.4.1.4329.15.3.3.1.9.1.1	Integer32	read-write	Table index for the WEP key.
WEP vnsWEPKeyValue	1.3.6.1.4.1.4329.15.3.3.1.9.1.2	WEPKeytype	read-write	Value of a WEP key for this VNS. This value is logically WRITE ONLY. Attempts to read this value shall return unsuccessful status and values of null or zero.
vns3rdPartyAPTable	1.3.6.1.4.1.4329.15.3.3.1.10		not-accessible	Contains a list of 3rd Party access points for the EWC.
vns3rdPartyAPEntry	1.3.6.1.4.1.4329.15.3.3.1.10.1		not-accessible	Configuration information for a 3rd party access point.
MAC apMacAddress	1.3.6.1.4.1.4329.15.3.3.1.10.1.1	MacAddress	read-write	Ethernet MAC address of the 3rd party access point.
IP apIPAddress	1.3.6.1.4.1.4329.15.3.3.1.10.1.2	IpAddress	read-write	IP address of the 3rd party access point.
vnsQoSTable	1.3.6.1.4.1.4329.15.3.3.1.11		not-accessible	This table contains list of per-VNS QoS related configuration.
vnsQoSEntry	1.3.6.1.4.1.4329.15.3.3.1.11.1		not-accessible	An entry related to QoS configuration for the VNS indexed by vnsIfIndex.
INT vnsQoSWirelessLegacyFlag	1.3.6.1.4.1.4329.15.3.3.1.11.1.1	INTEGER	read-write	This variable is used to enable/disable legacy QoS feature.
INT vnsQoSWirelessWMMFlag	1.3.6.1.4.1.4329.15.3.3.1.11.1.2	INTEGER	read-write	This variable is used to enable/disable WMM feature.
INT vnsQoSWireless80211eFlag	1.3.6.1.4.1.4329.15.3.3.1.11.1.3	INTEGER	read-write	This variable is used to enable/disable 802.11e feature.
INT vnsQoSWirelessTurboVoiceFlag	1.3.6.1.4.1.4329.15.3.3.1.11.1.4	INTEGER	read-write	This variable is used to enable/disable turbo feature.
INT vnsQoSPriorityOverrideFlag	1.3.6.1.4.1.4329.15.3.3.1.11.1.5	INTEGER	read-write	Enable/disable the use of DSCP to override Servic Class (SC) value.
INT vnsQoSPriorityOverrideSC	1.3.6.1.4.1.4329.15.3.3.1.11.1.6	INTEGER	read-write	Service class (SC) of the override value. This field has a meaning if vnsQoSPriorityOverrideFlag is enabled.
I32 vnsQoSPriorityOverrideDSCP	1.3.6.1.4.1.4329.15.3.3.1.11.1.7	Integer32	read-write	DSCP override value to be used for the service class. This field has a meaning if vnsQoSPriorityOverrideFlag is enabled.
OCT vnsQoSClassificationServiceClass	1.3.6.1.4.1.4329.15.3.3.1.11.1.8	OCTET STRING	read-write	Service Class value for the DSCP code. This field is 64-bytes long. Each byte represents mapping between DSCP and Service Class. Position of each byte in the array represents DSCP code and the content of each byte represents the service class value for that DSCP code. For example, second byte represents DSCP code 1 and its value represents SC value. Value for each byte is equivalent to either of: background = 0, bestEffort = 1, bronze = 2, silver = 3, gold = 4, platinum = 5, premiumVoice = 6, networkControl = 7
INT vnsQoSWirelessEnableUAPSD	1.3.6.1.4.1.4329.15.3.3.1.11.1.9	INTEGER	read-write	This variable is used to enable/disable U-APSD feature.
INT vnsQoSWirelessUseAdmControlVoice	1.3.6.1.4.1.4329.15.3.3.1.11.1.10	INTEGER	read-write	If enabled, admission control for voice traffic is used.
INT vnsQoSWirelessUseAdmControlVideo	1.3.6.1.4.1.4329.15.3.3.1.11.1.11	INTEGER	read-write	If enabled, admission control for vedio traffic is used. This field has a meaning if vnsQoSUseGlobalAdmVoice is enabled.
INT vnsQoSWirelessULPolicerAction	1.3.6.1.4.1.4329.15.3.3.1.11.1.12	INTEGER	read-write	If doNothing is selected, no action is taken. This is default value. If sendDELTStoClient is selected, AP will send DELTS if a client is abusing in uplink. This field has a meaning only if admission control is enabled for VO or VI.
INT vnsQoSWirelessDLPolicerAction	1.3.6.1.4.1.4329.15.3.3.1.11.1.13	INTEGER	read-write	If doNothing is selected, no action is taken. This is default value. If downgrade is selected, AP will downgrade all traffic to the highest AC that does not require CAC in downlink. If drop is selected, AP will drop client if it observes a client that is illegally using an AC that has CAC mandatory in downlink. This field has a meaning only if admission control is enabled for VO or VI.
INT vnsQoSWirelessUseAdmControlBestEffort	1.3.6.1.4.1.4329.15.3.3.1.11.1.14	INTEGER	read-write	If enabled, admission control for video traffic is set to Best Effort. This field has a meaning if vnsQoSUseGlobalAdmVoice is enabled.
INT vnsQoSWirelessUseAdmControlBackground	1.3.6.1.4.1.4329.15.3.3.1.11.1.15	INTEGER	read-write	If enabled, admission control for video traffic is set to Background. This field has a meaning if vnsQoSUseGlobalAdmVoice is enabled.
vnsWDSRFTable	1.3.6.1.4.1.4329.15.3.3.1.12		not-accessible	ontains definitions of the Wireless Distirbution System (WDS) VNS defined on this Controller.
vnsWDSRFEntry	1.3.6.1.4.1.4329.15.3.3.1.12.1		not-accessible	Configuration elements for a specific WDS VNS.
STR vnsWDSRFAPName	1.3.6.1.4.1.4329.15.3.3.1.12.1.1	DisplayString	read-write	AP name.
INT vnsWDSRFbgService	1.3.6.1.4.1.4329.15.3.3.1.12.1.2	INTEGER	read-write	Type of service offered by this radio.
INT vnsWDSRFaService	1.3.6.1.4.1.4329.15.3.3.1.12.1.3	INTEGER	read-write	Type of service offered by this radio.
STR vnsWDSRFPreferredParent	1.3.6.1.4.1.4329.15.3.3.1.12.1.4	DisplayString	read-write	Desired preferred parent.
STR vnsWDSRFBackupParent	1.3.6.1.4.1.4329.15.3.3.1.12.1.5	DisplayString	read-write	Desired backup parent.
INT vnsWDSRFBridge	1.3.6.1.4.1.4329.15.3.3.1.12.1.6	INTEGER	read-write	WDS bridge status.
vnsRateControlProfTable	1.3.6.1.4.1.4329.15.3.3.1.13		not-accessible	Table of Rate Control Profiles.
vnsRateControlProfEntry	1.3.6.1.4.1.4329.15.3.3.1.13.1		not-accessible	Name of a specific Rate Control Profile.
U32 vnsRateControlProfInd	1.3.6.1.4.1.4329.15.3.3.1.13.1.1	Unsigned32	read-write	A monotonically increasing integer which acts as index of entries within the named Rate Control Profiles.
STR vnsRateControlProfName	1.3.6.1.4.1.4329.15.3.3.1.13.1.2	DisplayString	read-write	Rate Control Profile Name.
U32 vnsRateControlCIR	1.3.6.1.4.1.4329.15.3.3.1.13.1.3	Unsigned32	read-write	Rate Control Average Rate (CIR) in kbps.
U32 vnsRateControlCBS	1.3.6.1.4.1.4329.15.3.3.1.13.1.4	Unsigned32	read-write	Rate Control Burst Size (CBS) in bytes.
vnsAPFilterTable	1.3.6.1.4.1.4329.15.3.3.1.14		not-accessible	Filters applied to Access Points via VNS settings and assignments.
vnsAPFilterEntry	1.3.6.1.4.1.4329.15.3.3.1.14.1		not-accessible	An entry containing filters definition for Access Points assigned to VNS that is identified by VNS index.
I32 vnsAPFilterRuleOrder	1.3.6.1.4.1.4329.15.3.3.1.14.1.1	Integer32	read-create	Position of the filter in the filter list.
INT vnsAPFilterRuleDirection	1.3.6.1.4.1.4329.15.3.3.1.14.1.2	INTEGER	read-create	Traffic direction related to the filter rule.
I32 vnsAPFilterAction	1.3.6.1.4.1.4329.15.3.3.1.14.1.3	Integer32	read-create	Allow or deny traffic for the filter.
IP vnsAPFilterIPAddress	1.3.6.1.4.1.4329.15.3.3.1.14.1.4	IpAddress	read-create	IP address applied to the filter.
IP vnsAPFilterMask	1.3.6.1.4.1.4329.15.3.3.1.14.1.5	IpAddress	read-create	The mask, number of bits set to one in the mask, applied to filter IP address.
I32 vnsAPFilterPortLow	1.3.6.1.4.1.4329.15.3.3.1.14.1.6	Integer32	read-create	Low port number for the filter.
I32 vnsAPFilterPortHigh	1.3.6.1.4.1.4329.15.3.3.1.14.1.7	Integer32	read-create	High port number for the filter.
I32 vnsAPFilterProtocol	1.3.6.1.4.1.4329.15.3.3.1.14.1.8	Integer32	read-create	Specific protocol for the filter.
INT vnsAPFilterEtherType	1.3.6.1.4.1.4329.15.3.3.1.14.1.9	INTEGER	read-create	Specific ethertype to the filter.
I32 vnsAPFilterRowStatus	1.3.6.1.4.1.4329.15.3.3.1.14.1.10	Integer32	read-create	RowStatus value for this table entry.
vnsStatsObjects	1.3.6.1.4.1.4329.15.3.3.2
I32 activeVNSSessionCount	1.3.6.1.4.1.4329.15.3.3.2.1	Integer32	read-write	Number of active VNSs.
vnsStatTable	1.3.6.1.4.1.4329.15.3.3.2.2		not-accessible	Description.
vnsStatEntry	1.3.6.1.4.1.4329.15.3.3.2.2.1		not-accessible	Description.
OCT vnsStatName	1.3.6.1.4.1.4329.15.3.3.2.2.1.1	OCTET STRING	read-write	Name of the VNS.
C64 vnsStatTxPkts	1.3.6.1.4.1.4329.15.3.3.2.2.1.2	Counter64	read-only	Trasmitted packets.
C64 vnsStatRxPkts	1.3.6.1.4.1.4329.15.3.3.2.2.1.3	Counter64	read-only	Received packtes.
C64 vnsStatTxOctects	1.3.6.1.4.1.4329.15.3.3.2.2.1.4	Counter64	read-only	Trasmitted octects.
C64 vnsStatRxOctects	1.3.6.1.4.1.4329.15.3.3.2.2.1.5	Counter64	read-only	Received octets.
C64 vnsStatMulticastTxPkts	1.3.6.1.4.1.4329.15.3.3.2.2.1.6	Counter64	read-only	Multicast trasmitted packets.
C64 vnsStatMulticastRxPkts	1.3.6.1.4.1.4329.15.3.3.2.2.1.7	Counter64	read-only	Multicast received packets.
C64 vnsStatBroadcastTxPkts	1.3.6.1.4.1.4329.15.3.3.2.2.1.8	Counter64	read-only	Broadcast trasmitted packets.
C64 vnsStatBroadcastRxPkts	1.3.6.1.4.1.4329.15.3.3.2.2.1.9	Counter64	read-only	Broadcast received packets.
C64 vnsStatRadiusTotRequests	1.3.6.1.4.1.4329.15.3.3.2.2.1.10	Counter64	read-only	Total requests sent to radius server.
C64 vnsStatRadiusReqFailed	1.3.6.1.4.1.4329.15.3.3.2.2.1.11	Counter64	read-only	Requests that failed to be processed by radius server.
C64 vnsStatRadiusReqRejected	1.3.6.1.4.1.4329.15.3.3.2.2.1.12	Counter64	read-only	Requests that have been rejected by radius server.
vnsExceptionStatTable	1.3.6.1.4.1.4329.15.3.3.2.3		not-accessible	Description.
vnsExceptionStatEntry	1.3.6.1.4.1.4329.15.3.3.2.3.1		not-accessible	Description.
OCT vnsExceptionFiterName	1.3.6.1.4.1.4329.15.3.3.2.3.1.1	OCTET STRING	read-write	Filter name.
C64 vnsExceptionStatPktsDenied	1.3.6.1.4.1.4329.15.3.3.2.3.1.2	Counter64	read-only	Total packets that are denied by defined filters.
C64 vnsExceptionStatPktsAllowed	1.3.6.1.4.1.4329.15.3.3.2.3.1.3	Counter64	read-only	Total packets that are allowed by defined filters.
vnsWDSStatTable	1.3.6.1.4.1.4329.15.3.3.2.4		not-accessible	Description.
vnsWDSStatEntry	1.3.6.1.4.1.4329.15.3.3.2.4.1		not-accessible	Description.
STR vnsWDSStatAPName	1.3.6.1.4.1.4329.15.3.3.2.4.1.1	DisplayString	read-write	AP name serving WDS VNS.
INT vnsWDSStatAPRole	1.3.6.1.4.1.4329.15.3.3.2.4.1.2	INTEGER	read-write	Role of the AP in WDS tree. All the statistics and configuration information in this table has no meaning if the role is unknown(-1).
STR vnsWDSStatAPRadio	1.3.6.1.4.1.4329.15.3.3.2.4.1.3	DisplayString	read-write	Radio and freq on which uplink WDS is established, N/A if connected over etherent (value are 'a:', 'b/g:', or 'N/A')
STR vnsWDSStatAPParent	1.3.6.1.4.1.4329.15.3.3.2.4.1.4	DisplayString	read-write	AP Name of the parent AP.
STR vnsWDSStatSSID	1.3.6.1.4.1.4329.15.3.3.2.4.1.5	DisplayString	read-write	SSID of the WDS VNS where parent WDS link is established.
C64 vnsWDSStatRxFrame	1.3.6.1.4.1.4329.15.3.3.2.4.1.6	Counter64	read-write	Received frames from the parent AP.
C64 vnsWDSStatTxFrame	1.3.6.1.4.1.4329.15.3.3.2.4.1.7	Counter64	read-write	Transmitted frames to the parent AP.
C64 vnsWDSStatRxError	1.3.6.1.4.1.4329.15.3.3.2.4.1.8	Counter64	read-write	Received frames in error from the parent AP.
C64 vnsWDSStatTxError	1.3.6.1.4.1.4329.15.3.3.2.4.1.9	Counter64	read-write	Transmitted frames in error to the parent AP.
I32 vnsWDSStatRxRSSI	1.3.6.1.4.1.4329.15.3.3.2.4.1.10	Integer32	read-write	Average Received Signal Strength Indicator (RSSI).
C64 vnsWDSStatRxRate	1.3.6.1.4.1.4329.15.3.3.2.4.1.11	Counter64	read-write	Average receive rate.
C64 vnsWDSStatTxRate	1.3.6.1.4.1.4329.15.3.3.2.4.1.12	Counter64	read-write	Average transmission rate.
vnsGlobalSetting	1.3.6.1.4.1.4329.15.3.3.3
wirelessQoS	1.3.6.1.4.1.4329.15.3.3.3.1
I32 maxVoiceBWforReassociation	1.3.6.1.4.1.4329.15.3.3.3.1.1	Integer32	read-write	Maximum voice bandwidth to be used for re-association.
I32 maxVoiceBWforAssociation	1.3.6.1.4.1.4329.15.3.3.3.1.2	Integer32	read-write	Maximum voice bandwidth to be used for association.
I32 maxVideoBWforReassociation	1.3.6.1.4.1.4329.15.3.3.3.1.3	Integer32	read-write	Maximum video bandwidth to be used for re-association.
I32 maxVideoBWforAssociation	1.3.6.1.4.1.4329.15.3.3.3.1.4	Integer32	read-write	Maximum video bandwidth to be used for association.
I32 maxBestEffortBWforReassociation	1.3.6.1.4.1.4329.15.3.3.3.1.5	Integer32	read-write	Maximum best effort bandwidth to be used for reassociation.
I32 maxBestEffortBWforAssociation	1.3.6.1.4.1.4329.15.3.3.3.1.6	Integer32	read-write	Maximum best effort bandwidth to be used for association.
I32 maxBackgroundBWforReassociation	1.3.6.1.4.1.4329.15.3.3.3.1.7	Integer32	read-write	Maximum background bandwidth to be used for reassociation.
I32 maxBackgroundBWforAssociation	1.3.6.1.4.1.4329.15.3.3.3.1.8	Integer32	read-write	Maximum background bandwidth to be used for association.
radiusInfo	1.3.6.1.4.1.4329.15.3.3.3.2
externalRadiusServerTable	1.3.6.1.4.1.4329.15.3.3.3.2.2		not-accessible	Table of external RADIUS servers available for authentication services.
externalRadiusServerEntry	1.3.6.1.4.1.4329.15.3.3.3.2.2.1		not-accessible	Configuration information about the RADIUS server entry.
STR externalRadiusServerName	1.3.6.1.4.1.4329.15.3.3.3.2.2.1.1	DisplayString	read-write	RADIUS server name.
STR externalRadiusServerAddress	1.3.6.1.4.1.4329.15.3.3.3.2.2.1.2	DisplayString	read-write	RADIUS server address, it can be either string or IP address.
OCT externalRadiusServerSharedSecret	1.3.6.1.4.1.4329.15.3.3.3.2.2.1.3	OCTET STRING	read-write	Shared secret between Radius and the client.
ROW externalRadiusServerRowStatus	1.3.6.1.4.1.4329.15.3.3.3.2.2.1.4	RowStatus	read-write	Row Status for the entry.
dasInfo	1.3.6.1.4.1.4329.15.3.3.3.3
I32 dasPort	1.3.6.1.4.1.4329.15.3.3.3.3.1	Integer32	read-write	Dynamic Authorization Server (DAS) port.
I32 dasReplayInterval	1.3.6.1.4.1.4329.15.3.3.3.3.2	Integer32	read-write	The time window for message timeliness and replay protection for DAS packets. Packets should be dropped that their time generation is outside of this specified interval. Value zero indicates that the timeliness checking will be performed.
INT advancedFilteringMode	1.3.6.1.4.1.4329.15.3.3.3.4	INTEGER	read-write	Value of 'enabled(1)' means EWC is operating in advanced filtering configuration mode. Value of 'disabled(0)' means EWC is operating in mode that is compatible with releases prior to 7.41. This field can only be set to 'enabled(1)' and after setting it to that value, the only way to undo that is by resetting the database.
INT radiusStrictMode	1.3.6.1.4.1.4329.15.3.3.3.5	INTEGER	read-write	If this variable set to true, then assignment of RADIUS server(s) to WLAN are automatic during WLAN creation, otherwise, assignment of RADIUS server(s) to WLAN must be done manually.
radiusFastFailoverEvents	1.3.6.1.4.1.4329.15.3.3.3.6
radiusFastFailoverEventsTable	1.3.6.1.4.1.4329.15.3.3.3.6.1		not-accessible	Table in which to configure which RADIUS servers will be sent interim accounting reports for stations when a fast failover incident occurs
radiusFastFailoverEventsEntry	1.3.6.1.4.1.4329.15.3.3.3.6.1.1		not-accessible	An entry for each radius server.
STR radiusFFOEid	1.3.6.1.4.1.4329.15.3.3.3.6.1.1.1	DisplayString	not-accessible	The IP address or hostname of configured radius server. If the hostname is created from GUI/CLI and the size is bigger than 64 characters, snmp will display the first 64 characters only.
INT fastFailoverEvents	1.3.6.1.4.1.4329.15.3.3.3.6.1.1.2	INTEGER	read-write	If true, send an interim accounting record to the RADIUS server for each affected station when a fast failover event occurs. This field can be modified when controller is operated in availablity paired mode and fast failover is enabled
dhcpRelayListeners	1.3.6.1.4.1.4329.15.3.3.3.7
U32 dhcpRelayListenersMaxEntries	1.3.6.1.4.1.4329.15.3.3.3.7.1	Unsigned32	read-only	Maximum number of servers to which DHCP messages are relayed .
U32 dhcpRelayListenersNumEntries	1.3.6.1.4.1.4329.15.3.3.3.7.2	Unsigned32	read-only	The current number of entries in the dhcpRelayListenersTable.
I32 dhcpRelayListenersNextIndex	1.3.6.1.4.1.4329.15.3.3.3.7.3	Integer32	read-only	This object indicates numerically lowest available index within this entity, which may be used for the value of index in the creation of new entry in dhcpRelayListenersTable. An index is considered available if the index falls within the range of 1 to dhcpRelayListenersMaxEntries and it is not being used to index an existing entry in the dhcpRelayListenersTable contained this entity. This value should only be used as guideline for the management application and there is no requirement on the management application to create entries based upon this index value. Value of zero indicates there is no more room for new dhcpRelayListenersTable creation.
dhcpRelayListenersTable	1.3.6.1.4.1.4329.15.3.3.3.7.4		not-accessible	A list of servers to which DHCP messages are relayed but from which no responses are expected.
dhcpRelayListenersEntry	1.3.6.1.4.1.4329.15.3.3.3.7.4.1		not-accessible	An entry for each dhcpRelayListeners.
U32 dhcpRelayListenersID	1.3.6.1.4.1.4329.15.3.3.3.7.4.1.1	Unsigned32	not-accessible	The id corresponds to the 'server number' in the controller GUI and CLI.
ROW dhcpRelayListenersRowStatus	1.3.6.1.4.1.4329.15.3.3.3.7.4.1.2	RowStatus	read-create	This object allows dynamic creation and deletion of entries within dhcpRelayListenersTable as well as activation and deactivation of these entries. For row creation, EWC only supports creatAndWait.
STR destinationName	1.3.6.1.4.1.4329.15.3.3.3.7.4.1.3	DisplayString	read-write	Text string uniquely identifying NAC Server Name. Allowable characters for this field are from the set of A-Z, a-z, -_!#$, 0-9, and space. max len is 63 chars Howerver, it is recommended to avoid leading and trailing spaces.
IP destinationIP	1.3.6.1.4.1.4329.15.3.3.3.7.4.1.4	IpAddress	read-write	IPv4 address to which DHCP messages are relayed.
INT clientAutologinOption	1.3.6.1.4.1.4329.15.3.3.3.8	INTEGER	read-write	Many devices such as those made by Apple(R) implement an autologin feature that prompts the user to login as soon as the device detects the presence of a Captive Portal. This feature sometimes causes problems for users who actually interact with the captive portal. hide(0) - Hide the captive portal from Autologin detector. redirect(1) - Redirect detection messages to the Captive Portal. This option is to allow client autologin to detect the captive portal & prompt the user to login. This may cause post-authentication redirection to fail. drop(2) - Drop detection messages.
authenticationAdvanced	1.3.6.1.4.1.4329.15.3.3.3.9
INT includeServiceType	1.3.6.1.4.1.4329.15.3.3.3.9.1	INTEGER	read-write	Include the Service-Type attribute in client access request messages when this field is set to enable(1).
I32 clientMessageDelayTime	1.3.6.1.4.1.4329.15.3.3.3.9.2	Integer32	read-write	This field specifies how long, in seconds, the notice Web page is displayed to the client when the topology changes as a result of a role change. The notice Web page indicates that authentication was successful and that the user must close all browser windows and then restart the browser for access to the network. Currently this is supported for Internal Captive Portal, Guest Portal, and Guest Splash.
INT radiusAccounting	1.3.6.1.4.1.4329.15.3.3.3.9.3	INTEGER	read-write	This field enables or disables RADIUS accounting. Disabling RADIUS accounting overrides the RADIUS accounting settings of individual WLAN Services. Enabling RADIUS accounting activates RADIUS accounting only in WLAN Services specifically configured to perform it.
INT serverUsageModel	1.3.6.1.4.1.4329.15.3.3.3.9.4	INTEGER	read-write	This field specifies RADIUS server failover behavior when the primary server goes down. When the primary server is down the controller moves on to the secondary or tertiary configured RADIUS Servers. If this field is set to primaryBackup(1), then the controller starts polling the primary RADIUS server to see if it is up. When the primary RADIUS server comes back, the controller automatically starts sending new access requests to the primary RADIUS server but pending requests continue with backup RADIUS server. The administrator can select between the two strategies, i.e. the existing roundRobin(0) or new primaryBackup(1). This only applies to Authentication, not to Accounting.
INT radacctStartOnIPAddr	1.3.6.1.4.1.4329.15.3.3.3.9.5	INTEGER	read-write	When this OID is set to disabled (0) the controller sends a RADIUS accounting start message as soon as it receives an Access-Accept for the user from a RADIUS server. When this OID is set to enabled(1) the controller defers sending the RADIUS accounting start message until an Access-Accept for the client is received and the client's IP address is known.
INT clientServiceTypeLogin	1.3.6.1.4.1.4329.15.3.3.3.9.6	INTEGER	read-write	When this OID is set to enabled(1) the controller sets the Service-Type attribute of a station's Access-Request to 'Login'. When this OID is set to disabled(0) the controller sets the Service-Type attribute of a station's Access-Request to 'Framed'. By default this OID is set to 'disabled'. You cannot use RADIUS servers to authenticate administrators for local server access when this OID is set to 'enabled'.
INT applyMacAddressFormat	1.3.6.1.4.1.4329.15.3.3.3.9.7	INTEGER	read-write	When this OID is set to enabled(1), the controller uses MAC-Based Authentication MAC address format (refer to radiusMacAddressFormatOption) for user authentication and accounting via RADIUS.
radiusExtnsSetting	1.3.6.1.4.1.4329.15.3.3.3.10
radiusExtnsSettingTable	1.3.6.1.4.1.4329.15.3.3.3.10.1		not-accessible	List of RADIUS servers that will be used.
radiusExtnsSettingEntry	1.3.6.1.4.1.4329.15.3.3.3.10.1.1		not-accessible	An entry for each RADIUS server.
I32 radiusExtnsIndex	1.3.6.1.4.1.4329.15.3.3.3.10.1.1.1	Integer32	not-accessible	A number uniquely identifying each conceptual row in the radiusExtnsSettingTable. This value also equivalent to etsysRadiusAuthServerIndex of enterasys-radius-auth-client-mib.txt file.
INT pollingMechanism	1.3.6.1.4.1.4329.15.3.3.3.10.1.1.2	INTEGER	read-write	This field specifies the method to determine the health of the RADIUS server. If set to useRFC5997StatusServerRequest(1), RFC 5997 Status-Server packets will be sent to the primary server to determine it's health. If set to authorizeAsActualUser(0), access-request messages for a specified user account will be sent to the primary server to determine it's health.
I32 serverPollingInterval	1.3.6.1.4.1.4329.15.3.3.3.10.1.1.3	Integer32	read-write	Interval in seconds for the controller to poll the primary server.
netflowAndMirrorN	1.3.6.1.4.1.4329.15.3.3.3.11
IP netflowDestinationIP	1.3.6.1.4.1.4329.15.3.3.3.11.1	IpAddress	read-write	The IP address for the Purview engine that will receive netflow records.
I32 netflowInterval	1.3.6.1.4.1.4329.15.3.3.3.11.2	Integer32	read-write	The netflow record sending interval.
I32 mirrorFirstN	1.3.6.1.4.1.4329.15.3.3.3.11.3	Integer32	read-write	If non-zero, the first N packets of a particular flow will be mirrored. If 0, all packets will be mirrored.
OCT mirrorL2Ports	1.3.6.1.4.1.4329.15.3.3.3.11.4	OCTET STRING	read-write	Configure the mirror port(s) on the controller. The default value is None. Only l2ports will be allowed to be selected and only when not referred to elsewhere (lag, topologies). The most significant bit of the most significant octet represents the first esa port (esa0). The second most significant bit of the most significant octet represents the second esa port (esa1) and so on.
INT radiusMacAddressFormatOption	1.3.6.1.4.1.4329.15.3.3.3.12	INTEGER	read-write	The controller allows configuring different kinds of Mac address format in RADIUS messages. option1: mac address format as XXXXXXXXXXXX option2: mac address format as XX:XX:XX:XX:XX:XX option3: mac address format as XX-XX-XX-XX-XX-XX option4: mac address format as XXXX.XXXX.XXXX option5: mac address format as XXXXXX-XXXXXX option6: mac address format as XX XX XX XX XX XX option7: mac address format as xxxxxxxxxxxx option8: mac address format as xx:xx:xx:xx:xx:xx option9: mac address format as xx-xx-xx-xx-xx-xx option10: mac address format as xxxx.xxxx.xxxx option11: mac address format as xxxxxx-xxxxxx option12: mac address format as xx xx xx xx xx xx
wlan	1.3.6.1.4.1.4329.15.3.3.4
U32 wlanMaxEntries	1.3.6.1.4.1.4329.15.3.3.4.1	Unsigned32	read-only	Maximum number of WLAN supported by the device.
U32 wlanNumEntries	1.3.6.1.4.1.4329.15.3.3.4.2	Unsigned32	read-only	The current number of entries in the wlanTable.
I32 wlanTableNextAvailableIndex	1.3.6.1.4.1.4329.15.3.3.4.3	Integer32	read-only	This object indicates numerically lowest available index within this entity, which may be used for the value of index in the creation of new entry in wlanTable. An index is considered available if the index falls within the range of 1 to wlanMaxEntries and it is not being used to index an existing entry in the wlanTable contained this entity. This value should only be used as guideline for the management application and there is no requirement on the management application to create entries based upon this index value. Value of zero indicates there is no more room for new wlanTable creation.
wlanTable	1.3.6.1.4.1.4329.15.3.3.4.4		not-accessible	Table of configured WLAN.
wlanEntry	1.3.6.1.4.1.4329.15.3.3.4.4.1		not-accessible	An entry for each WLAN.
U32 wlanID	1.3.6.1.4.1.4329.15.3.3.4.4.1.1	Unsigned32	read-only	Unique internal ID associated with WLAN.
ROW wlanRowStatus	1.3.6.1.4.1.4329.15.3.3.4.4.1.2	RowStatus	read-write	This object allows dynamic creation and deletion of entries within wlanTable as well as activation and deactivation of these entries. For row creation, EWC only supports creatAndWait. WLAN name must be set before making the row active and persistent. Any WLAN that is associated to a VNS cannot be deleted unless it is first disassociated from VNS before being deleted. Any inactive entry will not be persistent and it will be lost during controller's restart.
INT wlanServiceType	1.3.6.1.4.1.4329.15.3.3.4.4.1.3	INTEGER	read-write	Service type of WLAN.
STR wlanName	1.3.6.1.4.1.4329.15.3.3.4.4.1.4	DisplayString	read-write	Text string uniquely identifying WLAN within EWC. Allowable characters for this field are from the set of A-Z, a-z, -!#$:, 0-9, and space. Howerver, it is recommended to avoid leading and trailing spaces.
STR wlanSSID	1.3.6.1.4.1.4329.15.3.3.4.4.1.5	DisplayString	read-write	SSID (broadcast string) associated with WLAN. Allowable characters for this field are from the set of A-Z, a-z, _-.@, 0-9, and space. Howerver, it is recommendedto avoid leading and trailing spaces.
T/F wlanSynchronize	1.3.6.1.4.1.4329.15.3.3.4.4.1.6	TruthValue	read-write	If it is set to true, then WLAN will be replicated to peer controller if availability is configured and enabled.
T/F wlanEnabled	1.3.6.1.4.1.4329.15.3.3.4.4.1.7	TruthValue	read-write	This field is used to enable or disable this WLAN. If WLAN is disabled, then no traffic will be passed on behalf of this WLAN.
INT wlanDefaultTopologyID	1.3.6.1.4.1.4329.15.3.3.4.4.1.8	INTEGER	read-write	The ID of topology from topologyTable associated to this WLAN. Topology ID of -1 means no default topology is associated to this WLAN. Physical topologies cannot be assigned to WLAN. The default topology indicates which topology to use for this WLAN if there is no topology associated with VNS via policy assignment.
U32 wlanSessionTimeout	1.3.6.1.4.1.4329.15.3.3.4.4.1.9	Unsigned32	read-write	MU session that is associated to this WLAN will be terminated after elapse of this number of minutes from the start of its current session.
U32 wlanIdleTimeoutPreAuth	1.3.6.1.4.1.4329.15.3.3.4.4.1.10	Unsigned32	read-write	Elapse time between association and authentication after which MU session will be terminated if the user is idle this amount of time without being authenticated.
U32 wlanIdleSessionPostAuth	1.3.6.1.4.1.4329.15.3.3.4.4.1.11	Unsigned32	read-write	MU session that is associated to this WLAN will be terminated if the user is idle this amount of time after being authenticated.
T/F wlanSupressSSID	1.3.6.1.4.1.4329.15.3.3.4.4.1.12	TruthValue	read-write	If it is set to true then broadcast string (SSID) for this WLAN will not be broadcasted over the air.
T/F wlanDot11hSupport	1.3.6.1.4.1.4329.15.3.3.4.4.1.13	TruthValue	read-write	If it is set to true then dot11h support is enabled for clients associated to this WLAN.
T/F wlanDot11hClientPowerReduction	1.3.6.1.4.1.4329.15.3.3.4.4.1.14	TruthValue	read-write	If it is set to true then apply power reduction to dot11h clients associated to this WLAN. This field has meaning if wlanDot11hSupport is enabled (set to true).
T/F wlanProcessClientIE	1.3.6.1.4.1.4329.15.3.3.4.4.1.15	TruthValue	read-write	If it is set to true then clients that are associated to this WLAN their IE requests will be processed.
T/F wlanEngerySaveMode	1.3.6.1.4.1.4329.15.3.3.4.4.1.16	TruthValue	read-write	If it is set to true then engergy saving mode is enabled.
T/F wlanBlockMuToMuTraffic	1.3.6.1.4.1.4329.15.3.3.4.4.1.17	TruthValue	read-write	If it is set to true then two MU associated to this WLAN cannot communicate with each other.
T/F wlanRemoteable	1.3.6.1.4.1.4329.15.3.3.4.4.1.18	TruthValue	read-write	If it is set to true then this WLAN can be used as remote WLAN within mobility zone that this controller is partaking.
U32 wlanVNSID	1.3.6.1.4.1.4329.15.3.3.4.4.1.19	Unsigned32	read-only	The ID of the VNS that uses this WLAN. WLAN can be created but not used in any VNS, in that case alue of zero indicates WLAN has not been used in any VNS. The value of this field set during VNS creation no during the WLAN creation.
INT wlanRadioManagement11k	1.3.6.1.4.1.4329.15.3.3.4.4.1.20	INTEGER	read-write	When this bit is set to enable, the Radio Management (802.11k) feature is enabled on those APs who have this wlan configuration and 802.11k capability.
INT wlanBeaconReport	1.3.6.1.4.1.4329.15.3.3.4.4.1.21	INTEGER	read-write	Enable/disable AP to send out beacon report. This field is configurable only if wlanRadioManagement11k is set to enable(1).
INT wlanQuietIE	1.3.6.1.4.1.4329.15.3.3.4.4.1.22	INTEGER	read-write	Enable/disable AP to advertise a Quiet Element. This field is configurable only if wlanRadioManagement11k is set to enable(1).
INT wlanMirrorN	1.3.6.1.4.1.4329.15.3.3.4.4.1.23	INTEGER	read-write	prohibited(0): Mirroring is prohibited. bothDirection(1) : Both direction packets will be mirrored. rxDirectionOnly(2): Only receive direction packets will be mirrored. Note: This will only take effect when the user's runtime current Roles's MirrorN action is None.
INT wlanNetFlow	1.3.6.1.4.1.4329.15.3.3.4.4.1.24	INTEGER	read-write	Enable/disable netflow on this WLAN service.
INT wlanAppVisibility	1.3.6.1.4.1.4329.15.3.3.4.4.1.25	INTEGER	read-write	Enable/disable both application visibility and control for this WLAN service.
wlanStatsTable	1.3.6.1.4.1.4329.15.3.3.4.5		not-accessible	Stats related to WLAN (RFS) created on EWC.
wlanStatsEntry	1.3.6.1.4.1.4329.15.3.3.4.5.1		not-accessible	An entery for each existing WLAN on EWC.
U32 wlanStatsID	1.3.6.1.4.1.4329.15.3.3.4.5.1.1	Unsigned32	read-only	Unique internal ID associated with WLAN.
C32 wlanStatsAssociatedClients	1.3.6.1.4.1.4329.15.3.3.4.5.1.2	Counter32	read-only	Number of clients that are currently associated to this WLAN.
C32 wlanStatsRadiusTotRequests	1.3.6.1.4.1.4329.15.3.3.4.5.1.3	Counter32	read-only	Number of requests that were sent to RADIUS servers associated to this WLAN on behalf of MUs' requests using SSID associated to the WLAN for association, authentication or authorization to this WLAN.
C32 wlanStatsRadiusReqFailed	1.3.6.1.4.1.4329.15.3.3.4.5.1.4	Counter32	read-only	Number of requests that were sent to RADIUS servers associated to this WLAN on behalf of MUs' requests for association, authentication or authorization to this WLAN but failed to be processed by RADIUS servers.
C32 wlanStatsRadiusReqRejected	1.3.6.1.4.1.4329.15.3.3.4.5.1.5	Counter32	read-only	Number of requests that were sent to RADIUS servers associated to this WLAN on behalf of MUs' requests for association, authentication or authorization to this WLAN but rejected to be processed by RADIUS servers.
wlanPrivTable	1.3.6.1.4.1.4329.15.3.3.4.6		not-accessible	This table contains configuration of privacy settings for all configured WLAN on EWC. For each of the configured WLAN on the controller one entry is added to this table. Addition/deletion of entries in this table are automatic depending on the addition or deletion of entries in wlanTable table.
wlanPrivEntry	1.3.6.1.4.1.4329.15.3.3.4.6.1		not-accessible	An entry in wlanPrivTable for each configured WLAN on EWC. Each entry is indexed with corresponding wlan ID of wlanTable. The writable fields in this table can be modified depending on the corresponding wlanTable.
INT wlanPrivPrivacyType	1.3.6.1.4.1.4329.15.3.3.4.6.1.1	INTEGER	read-write	Type of privacy applied to the corresponding configured WLAN. Configuration of the other fields in this table depends on the value of this field, e.g. if this field is set to none(0), then no other field in this table are settable.
INT wlanPrivWEPKeyIndex	1.3.6.1.4.1.4329.15.3.3.4.6.1.2	INTEGER	read-write	Index of configured WEP. This field is required if and only if privacy type is staticWEP(1).
INT wlanPrivWEPKeyLength	1.3.6.1.4.1.4329.15.3.3.4.6.1.3	INTEGER	read-write	Key legnth for the configured WEP key. This field is required if and only if privacy type is staticWEP(1).
STR wlanPrivWEPKey	1.3.6.1.4.1.4329.15.3.3.4.6.1.4	DisplayString	read-write	The configured WEP key length must match the wlanPrivWEPKeyLength field. Any key with length longer or shorter than that length will be rejected. This field is required if and only if privacy type is staticWEP(1). This key can only be viewed in SNMPv3 mode with privacy.
INT wlanPrivWPAv1EncryptionType	1.3.6.1.4.1.4329.15.3.3.4.6.1.5	INTEGER	read-write	The type of encryption used for WPA version 1 associations. This OID is undefined unless wlanPrivPrivacyType is wpa (3) or wpaPSK (4) and wlanPrivWPAversion is set to wpaV1 (1) or wpaV1andV2 (3).
INT wlanPrivWPAv2EncryptionType	1.3.6.1.4.1.4329.15.3.3.4.6.1.6	INTEGER	read-write	The type of encryption used for WPA version 2 associations. This OID is undefined unless wlanPrivPrivacyType is wpa (3) or wpaPSK (4) and wlanPrivWPAversion is set to wpaV2 (2) or wpaV1 and V2 (3).
INT wlanPrivKeyManagement	1.3.6.1.4.1.4329.15.3.3.4.6.1.7	INTEGER	read-write	Key management option available for the WPA2. This field has meaning if privacy type is WPA with WPA2 option enabled. This field can be modified only if wlanPrivPrivacyType is set to wpa(3) and wlanPrivWPAversion set to wpaV2(2) or wpaV1andV2(3). .
T/F wlanPrivBroadcastRekeying	1.3.6.1.4.1.4329.15.3.3.4.6.1.8	TruthValue	read-write	Broadcast rekeying if this value is set to true. This field can be modified only if wlanPrivPrivacyType is set to wpa(3) or wpaPSK(4).
U32 wlanPrivRekeyInterval	1.3.6.1.4.1.4329.15.3.3.4.6.1.9	Unsigned32	read-write	Interval in seconds for requesting rekeying. This field has meaning if privacy type is WPA and broadcast rekeying is enabled (wlanPrivBroadcastRekeying is set to true). This field can be modified only if wlanPrivBroadcastRekeying is set to true.
T/F wlanPrivGroupKPSR	1.3.6.1.4.1.4329.15.3.3.4.6.1.10	TruthValue	read-write	Group Key Power Save Retry (GKPSR) value for the WPA type of privacy. This field can be modified only if wlanPrivPrivacyType is set to wpa(3) or wpaPSK(4).
OCT wlanPrivWPAPSK	1.3.6.1.4.1.4329.15.3.3.4.6.1.11	OCTET STRING	read-write	WPA-PSK shared key. This field has meaning if and only if WLAN privacy type is set to WPA-PSK. Input type can be either HEX formatted string or ASCII string. In case of HEX string, it must be 64 octets from set of hex characters. In case of ASCII string, the length is limited between 8 to 63 octets. This key can only be viewed in SNMPv3 mode with privacy. This field can be modified only if wlanPrivPrivacyType is set to wpaPSK(4).
INT wlanPrivWPAversion	1.3.6.1.4.1.4329.15.3.3.4.6.1.12	INTEGER	read-write	Type of wpa version selected. This field can be modified only if wlanPrivPrivacyType is set to wpa(3) or wpaPSK(4). Note: wpa version v1 only is not allowed. 0 - no wpa version selected. 1 - wpa version v1 selected. 2 - wpa version v2 selected. 3 - both wpa version v1 and v2 selected.
INT wlanPrivfastTransition	1.3.6.1.4.1.4329.15.3.3.4.6.1.13	INTEGER	read-write	When this field is set to enable(1), the 802.11r (fast transition) is enabled. This field can be modified only if wlanPrivPrivacyType is set to wpa(2).
INT wlanPrivManagementFrameProtection	1.3.6.1.4.1.4329.15.3.3.4.6.1.14	INTEGER	read-write	Disable(0) : The AP will not encrypt any management frames. Enable(1): The AP will encrypt management frames for clients who also support this feature. If the clients do not support this feature, they are still able to connect to the AP but with no management frames encryption. Require(2): The AP will only allow clients who have the PMF feature to connect. Supported management frames will be encrypted to 802.11w standards. Clients who do not support this feature will not be able to associate.
wlanAuthTable	1.3.6.1.4.1.4329.15.3.3.4.7		not-accessible	This table contains configuration of authentication settings for all configured WLAN on EWC. For each of the configured WLAN on the controller one entry is added to this table. Addition/deletion of entries in this table are automatic depending on the addition/deletion of entries in wlanTable table.
wlanAuthEntry	1.3.6.1.4.1.4329.15.3.3.4.7.1		not-accessible	An entry in wlanAuthTable for each configured WLAN on EWC. Each entry is indexed with corresponding wlan ID of wlanTable. The writable fields in this table can be modified depending on the corresponding wlanTable. Note: All the fields in this table except wlanAuthType and wlanAuthCollectAcctInformation have meaning if MAC-based authentication filed (wlanAuthMacBasedAuth) is set to true.
INT wlanAuthType	1.3.6.1.4.1.4329.15.3.3.4.7.1.1	INTEGER	read-write	The type of authentication applied to stations attempting to associate to a BSSID belonging to this WLAN Service. If the dot1x type is selected, then this WLAN must have privacy. When the dot1x or internalCP is selected, the controller must have a RADIUS server, and SNMP will auto assign one RADIUS server to this WLAN if the user did not assign one.
T/F wlanAuthMacBasedAuth	1.3.6.1.4.1.4329.15.3.3.4.7.1.2	TruthValue	read-write	MAC based authorization is enabled if this field is set to true. When this field set to true, SNMP will auto configure one RADIUS server to enable MAC authorization.
T/F wlanAuthMACBasedAuthOnRoam	1.3.6.1.4.1.4329.15.3.3.4.7.1.3	TruthValue	read-write	If it is set to true, the client will be forced to go through MAC based authorization when the client roamed. This field has meaning only when wlanAuthMacBasedAuth is set to true. This field can be modified only when wlanAuthMacBasedAuth is set to true.
T/F wlanAuthAutoAuthAuthorizedUser	1.3.6.1.4.1.4329.15.3.3.4.7.1.4	TruthValue	read-write	All authorized users will be considered authenticated automatically. This field has meaning only when wlanAuthMacBasedAuth is set to true. This field can be modified only when wlanAuthMacBasedAuth is set to true.
T/F wlanAuthAllowUnauthorizedUser	1.3.6.1.4.1.4329.15.3.3.4.7.1.5	TruthValue	read-write	Unauthorized users will be allowed if this field is set to true.This field has meaning only when wlanAuthMacBasedAuth is set to true. This field can be modified only when wlanAuthMacBasedAuth is set to true.
T/F wlanAuthRadiusIncludeAP	1.3.6.1.4.1.4329.15.3.3.4.7.1.6	TruthValue	read-write	AP serial number will be included in RADIUS request packet as VSA if this field is set to true.
T/F wlanAuthRadiusIncludeVNS	1.3.6.1.4.1.4329.15.3.3.4.7.1.7	TruthValue	read-write	VNS name will be included in RADIUS request packet as VSA if this field is set to true.
T/F wlanAuthRadiusIncludeSSID	1.3.6.1.4.1.4329.15.3.3.4.7.1.8	TruthValue	read-write	WLAN SSID will be included in RADIUS request packet as VSA if this field is set to true.
T/F wlanAuthRadiusIncludePolicy	1.3.6.1.4.1.4329.15.3.3.4.7.1.9	TruthValue	read-write	Policy name will be included in RADIUS request packet as VSA if this field is set to true.
T/F wlanAuthRadiusIncludeTopology	1.3.6.1.4.1.4329.15.3.3.4.7.1.10	TruthValue	read-write	Topology name will be included in RADIUS request packet as VSA if this field is set to true.
T/F wlanAuthRadiusIncludeIngressRC	1.3.6.1.4.1.4329.15.3.3.4.7.1.11	TruthValue	read-write	Ingress rate control name will be included in RADIUS request packet as VSA if this field is set to true.
T/F wlanAuthRadiusIncludeEgressRC	1.3.6.1.4.1.4329.15.3.3.4.7.1.12	TruthValue	read-write	Egress rate control name will be included in RADIUS request packet as VSA if this field is set to true.
T/F wlanAuthCollectAcctInformation	1.3.6.1.4.1.4329.15.3.3.4.7.1.13	TruthValue	read-write	Accounting information is collected for clients if this field is set to true.
T/F wlanAuthReplaceCalledStationIDWithZone	1.3.6.1.4.1.4329.15.3.3.4.7.1.14	TruthValue	read-write	Replace called station ID with Zone if this field is set to true.
T/F wlanAuthRadiusAcctAfterMacBaseAuthorization	1.3.6.1.4.1.4329.15.3.3.4.7.1.15	TruthValue	read-write	RADIUS accounting begins after MAC-based authorization completes if this field is set to true. This field has meaning only when wlanAuthMacBasedAuth is set to true. This field can be modified only when wlanAuthMacBasedAuth is set to true.
I32 wlanAuthRadiusTimeoutRole	1.3.6.1.4.1.4329.15.3.3.4.7.1.16	Integer32	read-write	Apply this role to clients when the RADIUS server timed out. '-1' is treat like access reject. Any other number is the Role ID. This field has meaning only when wlanAuthMacBasedAuth is set to true. This field can be modified only when wlanAuthMacBasedAuth is set to true.
INT wlanAuthRadiusOperatorNameSpace	1.3.6.1.4.1.4329.15.3.3.4.7.1.17	INTEGER	read-write	wlanAuthRadiusOperatorNameSpace is the Namespace ID as defined in RFC 5580. The value within this field contains the operator namespace identifier. The Namespace ID value is encoded in ASCII and has the following values. -1 : disabled. 48 : TADIG. 49 : REALM. 50 : E212. 51 : ICC.
STR wlanAuthRadiusOperatorName	1.3.6.1.4.1.4329.15.3.3.4.7.1.18	DisplayString	read-write	RADIUS accounting message will include this string when the wlanAuthRadiusOperatorNameSpace is not set to -1.
T/F wlanAuthMACBasedAuthReAuthOnAreaRoam	1.3.6.1.4.1.4329.15.3.3.4.7.1.19	TruthValue	read-write	If this field is set to true, the client will be forced to go through MAC based authorization when the client roams to another area. This field has meaning and can be modified only when wlanAuthMacBasedAuth is set to true.
wlanRadiusTable	1.3.6.1.4.1.4329.15.3.3.4.8		not-accessible	This table contains configuration of RADIUS settings for all configured WLAN on EWC. For each of the configured WLAN on the controller there may exist one or more entries of RADIUS server(s) serving the WLAN. Addition/deletion of entries in this table are automatic depending on the addition/deletion of entries in wlanTable table.
wlanRadiusEntry	1.3.6.1.4.1.4329.15.3.3.4.8.1		not-accessible	An entry in wlanRadiusTable for each RADIUS server used by the WLAN indexed by wlanID.
U32 wlanRadiusIndex	1.3.6.1.4.1.4329.15.3.3.4.8.1.1	Unsigned32	not-accessible	Internally generated index and it has no external meaning.
STR wlanRadiusName	1.3.6.1.4.1.4329.15.3.3.4.8.1.2	DisplayString	read-write	Name of the RADIUS server associated to this entry.
INT wlanRadiusUsage	1.3.6.1.4.1.4329.15.3.3.4.8.1.3	INTEGER	read-write	Usage type associated to this entry for authentication.
I32 wlanRadiusPriority	1.3.6.1.4.1.4329.15.3.3.4.8.1.4	Integer32	read-write	Priority associated to this entry for authentication. RADIUS servers are contacted for authentication requests in the order of their priority defined in this field. The highest priority servers (priorities with lower numerical values have higher priority order) are consulted first for any authentication request.
U32 wlanRadiusPort	1.3.6.1.4.1.4329.15.3.3.4.8.1.5	Unsigned32	read-write	The RADIUS authentication requests should be sent to this authentication port.
U32 wlanRadiusRetries	1.3.6.1.4.1.4329.15.3.3.4.8.1.6	Unsigned32	read-write	Maximum number of retries attempted for an specific authentication request.
U32 wlanRadiusTimeout	1.3.6.1.4.1.4329.15.3.3.4.8.1.7	Unsigned32	read-write	Number of seconds to wait for a response from authentication server for each request sent to the server before considering the request as failure.
T/F wlanRadiusNASUseVnsIP	1.3.6.1.4.1.4329.15.3.3.4.8.1.8	TruthValue	read-write	If this value is set to true, then VNS IP address associated to the WLAN indexed by wlanID to this entry is used as NAS IP address. Otherwise NAS IP address should be configured manually.
STR wlanRadiusNASIP	1.3.6.1.4.1.4329.15.3.3.4.8.1.9	DisplayString	read-write	NAS IP associated to this RADIUS server. Configuration of this field is directly affected by the value of wlanRadiusNASUseVnsIP.
T/F wlanRadiusNASIDUseVNSName	1.3.6.1.4.1.4329.15.3.3.4.8.1.10	TruthValue	read-write	If this value is set to true, then use VNS name associated to the WLAN indexed by wlanID for this entry as NAS ID. Otherwise NAS ID should be configured manually.
STR wlanRadiusNASID	1.3.6.1.4.1.4329.15.3.3.4.8.1.11	DisplayString	read-write	NAS ID associated to this RADIUS server. Configuration of this field is directly affected by the value of wlanRadiusNASIDUseVNSName.
INT wlanRadiusAuthType	1.3.6.1.4.1.4329.15.3.3.4.8.1.12	INTEGER	read-write	Authentication type used for this WLAN when using this RADIUS server to authenticate users.
wlanCPTable	1.3.6.1.4.1.4329.15.3.3.4.9		not-accessible	This table contains configuration of Captive Portal settings for all configured WLAN on EWC. For each of the configured WLAN on the controller one entry is added to this table. Addition/deletion of entries in this table are automatic depending on the addition/deletion of entries in wlanTable table. This table can be accessed using SNMPv3 on behalf of users with privacy.
wlanCPEntry	1.3.6.1.4.1.4329.15.3.3.4.9.1		not-accessible	An entry in wlanCPTable for each configured WLAN on EWC. Each entry is indexed with corresponding wlan ID of wlanTable. The writable fields in this table can be modified depending on the corresponding wlanTable and type of CP assigned to the WLAN. If the authentication type is 'disabled(0)' for the WLAN, then all other entries in this table have no meaning.
INT wlanCPAuthType	1.3.6.1.4.1.4329.15.3.3.4.9.1.1	INTEGER	read-write	Type of authentication applied to MU requesting association using SSID associated to this WLAN.
T/F wlanCP802HttpRedirect	1.3.6.1.4.1.4329.15.3.3.4.9.1.2	TruthValue	read-write	If it is set to true, then CP will be redirected to configured CP. This value has meaning only for CP of the type 'dot1x(3)'.
IP wlanCPExtConnection	1.3.6.1.4.1.4329.15.3.3.4.9.1.3	IpAddress	read-write	IP address of the interface for this CP.
U32 wlanCPExtPort	1.3.6.1.4.1.4329.15.3.3.4.9.1.4	Unsigned32	read-write	The port associated to the CP IP address.
T/F wlanCPExtEnableHttps	1.3.6.1.4.1.4329.15.3.3.4.9.1.5	TruthValue	read-write	HTTPS support is enabled if this field is set to true.
INT wlanCPExtEncryption	1.3.6.1.4.1.4329.15.3.3.4.9.1.6	INTEGER	read-write	Type of encryption for the CP.
OCT wlanCPExtSharedSecret	1.3.6.1.4.1.4329.15.3.3.4.9.1.7	OCTET STRING	read-write	Shared secret used for this captive portal.
T/F wlanCPExtTosOverride	1.3.6.1.4.1.4329.15.3.3.4.9.1.8	TruthValue	read-write	Override ToS of NAC server usage only.
U32 wlanCPExtTosValue	1.3.6.1.4.1.4329.15.3.3.4.9.1.9	Unsigned32	read-write	ToS value for NAC server only.
T/F wlanCPExtAddIPtoURL	1.3.6.1.4.1.4329.15.3.3.4.9.1.10	TruthValue	read-write	If this value is set to true, then add EWC IP address and port number to the redirection URL.
T/F wlanCPIntLogoffButton	1.3.6.1.4.1.4329.15.3.3.4.9.1.11	TruthValue	read-write	If set to true provide 'Logoff' button to the user in CP page.
T/F wlanCPIntStatusCheckButton	1.3.6.1.4.1.4329.15.3.3.4.9.1.12	TruthValue	read-write	If set to true provide 'Status Check' button to the user in CP page.
STR wlanCPReplaceIPwithFQDN	1.3.6.1.4.1.4329.15.3.3.4.9.1.13	DisplayString	read-write	Replace CP gateway IP address with FQDN.
INT wlanCPSendLoginTo	1.3.6.1.4.1.4329.15.3.3.4.9.1.14	INTEGER	read-write	This field indicates to what URL the successful login session must be redirected. This field qualifies wlanCPRedirectURL.
STR wlanCPRedirectURL	1.3.6.1.4.1.4329.15.3.3.4.9.1.15	DisplayString	read-write	Text string identifying default redirection URL.
U32 wlanCPGuestAccLifetime	1.3.6.1.4.1.4329.15.3.3.4.9.1.16	Unsigned32	read-write	This value indicates for how many days the guest account is valid. Value of zero indicates that there is no limit for the guest account.
T/F wlanCPGuestAllowedLifetimeAcct	1.3.6.1.4.1.4329.15.3.3.4.9.1.17	TruthValue	read-write	If this value is set to true, then guest admin can obtain lifetime account.
U32 wlanCPGuestSessionLifetime	1.3.6.1.4.1.4329.15.3.3.4.9.1.18	Unsigned32	read-write	The guess account session using this CP cannot last longer than this number of hours. Value of zero means there is no limit for the session.
STR wlanCPGuestIDPrefix	1.3.6.1.4.1.4329.15.3.3.4.9.1.19	DisplayString	read-write	The prefix used for guest portal user ID label.
U32 wlanCPGuestMinPassLength	1.3.6.1.4.1.4329.15.3.3.4.9.1.20	Unsigned32	read-write	Minimum password length for the guest user account associated to this WLAN.
U32 wlanCPGuestMaxConcurrentSession	1.3.6.1.4.1.4329.15.3.3.4.9.1.21	Unsigned32	read-write	Maximum number of the guest users can use this set of credentials to access this concurrent session.
T/F wlanCPUseHTTPSforConnection	1.3.6.1.4.1.4329.15.3.3.4.9.1.22	TruthValue	read-write	When this value set to true, use HTTPS for user connection. It has meaning only when wlanCPAuthType is set to internalCP(2) or easyGuestCP(5) or guestSplash(6)
STR wlanCPIdentity	1.3.6.1.4.1.4329.15.3.3.4.9.1.23	DisplayString	read-write	wlanCPIdentity is used to identify the EWC to the external captive portal server (ECP) and the ECP to the EWC.
STR wlanCPCustomSpecificURL	1.3.6.1.4.1.4329.15.3.3.4.9.1.24	DisplayString	read-write	After a user successfully logs in, the user will be redirected to the URL as defined in the wlanCPCustomSpecificURL.
BIT wlanCPSelectionOption	1.3.6.1.4.1.4329.15.3.3.4.9.1.25	Bits	read-write	Append the above parameter(s) to the EWC captive portal redirection URL if one or more of the bits are set.
C32 wlanUnsecuredWlanCounts	1.3.6.1.4.1.4329.15.3.3.4.10	Counter32	read-only	Total number of WLAN with security issues. The details of security issues can be found in wlanSecurityReportTable.
wlanSecurityReportTable	1.3.6.1.4.1.4329.15.3.3.4.11		not-accessible	This table contains the weak configuration settings for all configured WLAN on EWC. For each of the configured WLAN on the controller there exist one entry in this table. Addition/deletion of entries in this table are automatic depending on the addition or deletion of entries in wlanTable table. This table can be accessed using SNMPv3 on behalf of users with privacy.
wlanSecurityReportEntry	1.3.6.1.4.1.4329.15.3.3.4.11.1		not-accessible	An entry in wlanSecurityReportTable for each configured WLAN on EWC. Each entry is indexed with corresponding wlan ID of wlanTable.
INT wlanSecurityReportFlag	1.3.6.1.4.1.4329.15.3.3.4.11.1.1	INTEGER	read-only	Value of secureSetting(2) indicates that WLAN has secure configuration.
BIT wlanSecurityReportUnsecureType	1.3.6.1.4.1.4329.15.3.3.4.11.1.2	Bits	read-only	bit 0: by setting this bit means this WLAN does not use any kind of encryption bit 1: by setting this bit means this WLAN uses weak WEP encryption bit 2: by setting this bit means this WLAN uses weak tkip encryption bit 3: by setting this bit means this WLAN uses default SSID bit 4: by setting this bit means this WLAN uses HotSpot SSID bit 5: by setting this bit means this WLAN uses Rainbow SSID bit 6: by setting this bit means this WLAN uses dictionary word as an encryption key bit 7: by setting this bit means this WLAN uses dictionary word in an encryption key string bit 8: by setting this bit means this WLAN uses a short password key
STR wlanSecurityReportNotes	1.3.6.1.4.1.4329.15.3.3.4.11.1.3	DisplayString	read-only	Textual description of any security issues related to the WLAN is reflected in this field.
wlanRadiusServerTable	1.3.6.1.4.1.4329.15.3.3.4.12		not-accessible	This table contains configuration of RADIUS Servers settings for all configured WLANs on the Wireless Controller. For each of the configured WLANs on the controller there may exist one or more entries of RADIUS server(s) serving the WLAN. Addition/deletion of entries in this table are automatic depending on the addition/deletion of entries in wlanTable table.
wlanRadiusServerEntry	1.3.6.1.4.1.4329.15.3.3.4.12.1		not-accessible	An entry in wlanRadiusServerTable for each RADIUS server used by the WLAN indexed by wlanID and radiusId. The radiusId is the controller's internal radius server index.
U32 radiusId	1.3.6.1.4.1.4329.15.3.3.4.12.1.1	Unsigned32	not-accessible	Controller's internal RADIUS index.
STR wlanRadiusServerName	1.3.6.1.4.1.4329.15.3.3.4.12.1.2	DisplayString	read-only	Name of the RADIUS server.
INT wlanRadiusServerUse	1.3.6.1.4.1.4329.15.3.3.4.12.1.3	INTEGER	read-write	use : This means that this WLAN service indexed by wlanID uses this RADIUS server which it is indexed by the radiusId.
BIT wlanRadiusServerUsage	1.3.6.1.4.1.4329.15.3.3.4.12.1.4	Bits	read-write	bit 0: By setting this bit, this RADIUS server is used for authentication. This bit has meaning only when wlanAuthType is set to internalCP(2), dot1x(3), or externalCP(4). bit 1: By setting this bit, this RADIUS server is used for MAC-based authentication. This bit has meaning only when wlanAuthMacBasedAuth is set to true. bit 2: By setting this bit, this RADIUS server is used for accounting. This bit has meaning only when wlanAuthType is set to internalCP(2), dot1x(3), or externalCP(4).
T/F wlanRadiusServerAuthUseVNSIPAddr	1.3.6.1.4.1.4329.15.3.3.4.12.1.5	TruthValue	read-write	When this value set to true, use the VNS's IP address as NAS IP address during the authentication.
STR wlanRadiusServerAuthNASIP	1.3.6.1.4.1.4329.15.3.3.4.12.1.6	DisplayString	read-write	Use this IP address as the NAS IP addresss during the authentication. The default IP address is the VNS IP address. This field has meaning only when the wlanRadiusServerUsage's bit 0 is set.
T/F wlanRadiusServerAuthUseVNSName	1.3.6.1.4.1.4329.15.3.3.4.12.1.7	TruthValue	read-write	When this value set to true, use the VNS's name as the NAS identifier during the authentication.
STR wlanRadiusServerAuthNASId	1.3.6.1.4.1.4329.15.3.3.4.12.1.8	DisplayString	read-write	Use this name as the NAS identifier during the authentication. The default name is the VNS name. This field has meaning only when the wlanRadiusServerUsage's bit 0 is set.
INT wlanRadiusServerAuthAuthType	1.3.6.1.4.1.4329.15.3.3.4.12.1.9	INTEGER	read-write	Authentication type. This field has meaning only when the wlanRadiusServerUsage's bit 0 is set.
T/F wlanRadiusServerAcctUseVNSIPAddr	1.3.6.1.4.1.4329.15.3.3.4.12.1.10	TruthValue	read-write	When this value set to true, use the VNS's IP address as NAS IP address during the accounting.
STR wlanRadiusServerAcctNASIP	1.3.6.1.4.1.4329.15.3.3.4.12.1.11	DisplayString	read-write	Use this IP address as the NAS IP addresss during the accounting. The default IP address is the VNS IP address. This field has meaning only when the wlanRadiusServerUsage's bit 2 is set.
T/F wlanRadiusServerAcctUseVNSName	1.3.6.1.4.1.4329.15.3.3.4.12.1.12	TruthValue	read-write	When this value set to true, use the VNS's name as the NAS identifier during the accounting.
STR wlanRadiusServerAcctNASId	1.3.6.1.4.1.4329.15.3.3.4.12.1.13	DisplayString	read-write	Use this name as the NAS identifier during the accounting. The default name is the VNS name. This field has meaning only when the wlanRadiusServerUsage's bit 2 is set.
T/F wlanRadiusServerAcctSIAR	1.3.6.1.4.1.4329.15.3.3.4.12.1.14	TruthValue	read-write	If this value is set to true, then the controller sends interrim accounting records for fast failover events. This field has meaning only when the wlanRadiusServerUsage's bit 2 is set.
T/F wlanRadiusServerMacUseVNSIPAddr	1.3.6.1.4.1.4329.15.3.3.4.12.1.15	TruthValue	read-write	When this value set to true, use the VNS's IP address as NAS IP address during the MAC based authentication.
STR wlanRadiusServerMacNASIP	1.3.6.1.4.1.4329.15.3.3.4.12.1.16	DisplayString	read-write	Use this IP address as the NAS IP addresss during the MAC based authentication. The default IP address is the VNS IP address. This field has meaning only when the wlanRadiusServerUsage's bit 1 is set.
T/F wlanRadiusServerMacUseVNSName	1.3.6.1.4.1.4329.15.3.3.4.12.1.17	TruthValue	read-write	When this value set to true, use the VNS's name as the NAS identifier during the MAC based authentication.
STR wlanRadiusServerMacNASId	1.3.6.1.4.1.4329.15.3.3.4.12.1.18	DisplayString	read-write	Use this name as the NAS identifier during the MAC based authentication. The default name is the VNS name. This field has meaning only when the wlanRadiusServerUsage's bit 1 is set.
INT wlanRadiusServerMacAuthType	1.3.6.1.4.1.4329.15.3.3.4.12.1.19	INTEGER	read-write	Authentication type. This field has meaning only when the wlanRadiusServerUsage's bit 1 is set.
STR wlanRadiusServerMacPW	1.3.6.1.4.1.4329.15.3.3.4.12.1.20	DisplayString	read-write	The password is used for MAC based authentication. This field has meaning only when the wlanRadiusServerUsage's bit 1 is set.
topology	1.3.6.1.4.1.4329.15.3.4
topologyConfig	1.3.6.1.4.1.4329.15.3.4.1
topologyTable	1.3.6.1.4.1.4329.15.3.4.1.1		not-accessible	List of topologies configured on EWC.
topologyEntry	1.3.6.1.4.1.4329.15.3.4.1.1.1		not-accessible	Configuration information about a topology in topology table. EWC supports different types of topologies, therefore, for complete configuration of a topology not all fields are necessary to be defined or have meaning. Definition of each field in this table specifies topolog-specific characteristics of the field and its relevance.
U32 topologyID	1.3.6.1.4.1.4329.15.3.4.1.1.1.1	Unsigned32	not-accessible	Unique internal identifier of the topology. This item is generated internally by EWC and has no external meaning.
STR topologyName	1.3.6.1.4.1.4329.15.3.4.1.1.1.2	DisplayString	read-write	Name associated with topology. This name must be unique within EWC. Allowable characters for this field are from the set of A-Z, a-z, -!#$:, 0-9, and space. Howerver, it is recommended to avoid leading and trailing spaces.
INT topologyMode	1.3.6.1.4.1.4329.15.3.4.1.1.1.3	INTEGER	read-write	Type of this topology. This field implies the meaning and necessity of other attributes associated to the topology.
INT topologyTagged	1.3.6.1.4.1.4329.15.3.4.1.1.1.4	INTEGER	read-write	If topology is tagged, then a VLAN ID must be assigned to the topology. Meaning associated to this field is topology specific: - For Admin topology (management port) is always untagged - Ror routed topology has no meaning and always untagged - For all other topologies this field is configurable.
I32 topologyVlanID	1.3.6.1.4.1.4329.15.3.4.1.1.1.5	Integer32	read-write	VLAN ID assigned to a tagged topology. For untagged topology this field has no meaning and it is set to -1.
OCT topologyEgressPort	1.3.6.1.4.1.4329.15.3.4.1.1.1.6	OCTET STRING	read-write	Egress port associated to this topology if it is tagged and VLANID defined for the topology. This field is represented as octect string: The most significant bit of most significant octet represent first physical port (lowest number port) and second most significant bit of most significant octet represent second physical port and so on. Meaning associated to this field is topology specific: - For Admin topology (management port) this field has no meaning. - Ror routed topology this field has no meaning - For all other topologies: physical, bridge at controller, and bridge at AP topologies this field is configurable.
T/F topologyLayer3	1.3.6.1.4.1.4329.15.3.4.1.1.1.7	TruthValue	read-write	If set to true, then topology has layer three persence. Any topology with layer three presence must have IP address and gateway assigned to it. Meaning associated to this field is topology specific: - For Admin topology (management port) it is always set to true. - Ror bridge at AP this field has no meaning and it is set to false. - For routed and physical topologies it is always set to true. - For bridge at controller type of topology this field is configurable.
IP topologyIPAddress	1.3.6.1.4.1.4329.15.3.4.1.1.1.8	IpAddress	read-write	IP address assigned to the topology as its interface. Meaning associated to this field is topology specific: - This field has meaning if topology has layer three presence. - Ror bridge at AP this field has no meaning and set 0.0.0.0.
IP topologyIPMask	1.3.6.1.4.1.4329.15.3.4.1.1.1.9	IpAddress	read-write	Mask for topology's IP address. This field is only applicable to those topologies that have IP address assigned to them, otherwise it is set either to 255.255.255.255 or 0.0.0.0.
U32 topologyMTUsize	1.3.6.1.4.1.4329.15.3.4.1.1.1.10	Unsigned32	read-write	Default MTU size for the topology. This field is only configurable for a topologies that has layer three presence.
IP topologyGateway	1.3.6.1.4.1.4329.15.3.4.1.1.1.11	IpAddress	read-write	Gateway associated to this topology. This field has meaning for a topology that has layer three presence.
INT topologyDHCPUsage	1.3.6.1.4.1.4329.15.3.4.1.1.1.12	INTEGER	read-write	The type of DHCP to be used for IP address assignment to associated MU. This field has meaning only if the topology has layer three persense. Meaning associated to this field is topology specific: - For Admin topology (management port) has no meaning. - Ror bridge at AP this field has no meaning. - For all other topologies that their layer three presence is enabled this field is configurable.
T/F topologyAPRegistration	1.3.6.1.4.1.4329.15.3.4.1.1.1.13	TruthValue	read-write	If set to true, then AP registration can be achieved using via this topology. Meaning associated to this field is topology specific: - Always false for Admin (management port) and routed topologies - Always false and has no meaning for bridge at AP topology. - For physical and bridge at controller type topologies that have layer three presence this field can be set to either true or false.
T/F topologyManagementTraffic	1.3.6.1.4.1.4329.15.3.4.1.1.1.14	TruthValue	read-write	If set to true, then management data traffic is allowed on this topology. Meaning associated to this field is topology specific: - Always true for Admin topology (management port) - Has no meaning for bridge at AP type topologies - For all other topologies that have layer three presence this field can be set to either true or false.
T/F topologySynchronize	1.3.6.1.4.1.4329.15.3.4.1.1.1.15	TruthValue	read-write	If set to true, then topology must be synchronized with peer controller in availability mode operation. Meaning associated to this field is topology specific: - Always false for Admin topology (management port) - Has no meaning for topologies associated to physical ports. - For all other topologies: bridge at controller, routed and bridge at AP type topologies this field can be set to either true or false.
IP topologySyncGateway	1.3.6.1.4.1.4329.15.3.4.1.1.1.16	IpAddress	read-write	Gateway associated to synchronized topology. This field has meaning for those topologies that their topologySynchornize field is set to true.
IP topologySyncMask	1.3.6.1.4.1.4329.15.3.4.1.1.1.17	IpAddress	read-write	Mask of synchronized gateway IP address. This field has meaning for those topologies that their topologySynchornize field is set to true.
IP topologySyncIPStart	1.3.6.1.4.1.4329.15.3.4.1.1.1.18	IpAddress	read-write	Range of IP addresses assigned to remote synchronized topology. This IP address represents starting IP address. This field has meaning for those topologies that their topologySynchornize field is set to true.
IP topologySyncIPEnd	1.3.6.1.4.1.4329.15.3.4.1.1.1.19	IpAddress	read-write	Range of IP addresses assigned to remote synchronized topology. This IP address represents ending IP address. This field has meaning for those topologies that their topologySynchornize field is set to true.
STR topologyStaticIPv6Address	1.3.6.1.4.1.4329.15.3.4.1.1.1.20	DisplayString	read-write	Statically configured IPv6 address assigned to the admin port.
STR topologyLinkLocalIPv6Address	1.3.6.1.4.1.4329.15.3.4.1.1.1.21	DisplayString	read-only	Automatically generated link-local IPv6 address assigned to the admin port.
U32 topologyPreFixLength	1.3.6.1.4.1.4329.15.3.4.1.1.1.22	Unsigned32	read-write	The prfix length of the statically configured IPv6 address of the topology.
STR topologyIPv6Gateway	1.3.6.1.4.1.4329.15.3.4.1.1.1.23	DisplayString	read-write	The gateway of IPv6 address that is associated to the admin topology.
INT topologyDynamicEgress	1.3.6.1.4.1.4329.15.3.4.1.1.1.24	INTEGER	read-write	Enable/disable dynamic egress for this topology. Dynamic egress allows a station to receive from this VLAN if it can send to this VLAN.
INT topologyIsGroup	1.3.6.1.4.1.4329.15.3.4.1.1.1.25	INTEGER	read-write	When this flag is yes, this means the topology is created as a group topology.
OCT topologyGroupMembers	1.3.6.1.4.1.4329.15.3.4.1.1.1.26	OCTET STRING	read-write	This field specifies the topologies for this group. This field has meaning only when topologyIsGroup is set to 1. This field is represented as octect string. The most significant bit of the most significant octet of the octet string represents the first topology with topologyID = 0 and second most significant bit of the most significant octet represents the second topology with topologyID = 1 and so on.
I32 topologyMemberId	1.3.6.1.4.1.4329.15.3.4.1.1.1.27	Integer32	read-write	-1 : Means this topology is not a member of a group topology. valid topology ID : Means this topology is a member of a configured group topology that has this group topology ID.
topologyStat	1.3.6.1.4.1.4329.15.3.4.2
topoStatTable	1.3.6.1.4.1.4329.15.3.4.2.1		not-accessible	Statistics describing traffic transmitted or received for a single topology. This is the traffic on the topology that is coming from or going to destinations on the wired network.
topoStatEntry	1.3.6.1.4.1.4329.15.3.4.2.1.1		not-accessible	Statistic related an entry in topology table.
STR topoStatName	1.3.6.1.4.1.4329.15.3.4.2.1.1.1	DisplayString	read-only	Topology name.
C64 topoStatTxPkts	1.3.6.1.4.1.4329.15.3.4.2.1.1.2	Counter64	read-only	Number of packets transmitted to the wired network on the topology/vlan.
C64 topoStatRxPkts	1.3.6.1.4.1.4329.15.3.4.2.1.1.3	Counter64	read-only	Number of packets received from the wired network on the topology/vlan.
C64 topoStatTxOctets	1.3.6.1.4.1.4329.15.3.4.2.1.1.4	Counter64	read-only	Number of octets transmitted in frames to the wired network on the topology/vlan.
C64 topoStatRxOctets	1.3.6.1.4.1.4329.15.3.4.2.1.1.5	Counter64	read-only	Number of octets received in frames from the wired network on the topology/vlan.
C64 topoStatMulticastTxPkts	1.3.6.1.4.1.4329.15.3.4.2.1.1.6	Counter64	read-only	Number of multicast frames transmitted to the wired network on the topology/vlan.
C64 topoStatMulticastRxPkts	1.3.6.1.4.1.4329.15.3.4.2.1.1.7	Counter64	read-only	Number of multicast frames received from the wired network on the topology/vlan.
C64 topoStatBroadcastTxPkts	1.3.6.1.4.1.4329.15.3.4.2.1.1.8	Counter64	read-only	Number of broadcast frames transmitted to the wired network on the topology/vlan.
C64 topoStatBroadcastRxPkts	1.3.6.1.4.1.4329.15.3.4.2.1.1.9	Counter64	read-only	Number of broadcast frames received from the wired network on the topology/vlan.
C64 topoStatFrameChkSeqErrors	1.3.6.1.4.1.4329.15.3.4.2.1.1.10	Counter64	read-only	Number of frames with checksum errors received from the wired network on the topology/vlan.
C64 topoStatFrameTooLongErrors	1.3.6.1.4.1.4329.15.3.4.2.1.1.11	Counter64	read-only	Number of oversized frames received from the wired network on the topology/vlan.
topoExceptionStatTable	1.3.6.1.4.1.4329.15.3.4.2.2		not-accessible	The table contains list of exception-specific filters statistics for configured topologies in EWC.
topoExceptionStatEntry	1.3.6.1.4.1.4329.15.3.4.2.2.1		not-accessible	An entry in topology exception statistic table.
OCT topoExceptionFiterName	1.3.6.1.4.1.4329.15.3.4.2.2.1.1	OCTET STRING	read-write	Exception filter name.
C64 topoExceptionStatPktsDenied	1.3.6.1.4.1.4329.15.3.4.2.2.1.2	Counter64	read-only	Number of packets that were denied by defined filters since device's last restart.
C64 topoExceptionStatPktsAllowed	1.3.6.1.4.1.4329.15.3.4.2.2.1.3	Counter64	read-only	Number packets that were allowed by defined filters since device's last restart.
topoWireStatTable	1.3.6.1.4.1.4329.15.3.4.2.3		not-accessible	The table contains statistics describing traffic transmitted or received unencapsulated (i.e. not wrapped in WASSP) for each topology
topoWireStatEntry	1.3.6.1.4.1.4329.15.3.4.2.3.1		not-accessible	Statistics describing traffic transmitted or received unencapsulated (i.e. not wrapped in WASSP) for a single topology. This is the traffic on the topology that is coming from or going to destinations on the wired network other than to the controller's APs.
STR topoWireStatName	1.3.6.1.4.1.4329.15.3.4.2.3.1.1	DisplayString	read-only	Topology name.
C64 topoWireStatTxPkts	1.3.6.1.4.1.4329.15.3.4.2.3.1.2	Counter64	read-only	Number of packets transmitted unencapsulated to the wired network on the topology/vlan.
C64 topoWireStatRxPkts	1.3.6.1.4.1.4329.15.3.4.2.3.1.3	Counter64	read-only	Number of packets received unencapsulated from the wired network on the topology/vlan.
C64 topoWireStatTxOctets	1.3.6.1.4.1.4329.15.3.4.2.3.1.4	Counter64	read-only	Number of octets transmitted in unencapsulated frames to the wired network on the topology/vlan.
C64 topoWireStatRxOctets	1.3.6.1.4.1.4329.15.3.4.2.3.1.5	Counter64	read-only	Number of octets received in unencapsulated frames to the wired network on the topology/vlan.
C64 topoWireStatMulticastTxPkts	1.3.6.1.4.1.4329.15.3.4.2.3.1.6	Counter64	read-only	Number of multicast frames transmitted unencapsulated to the wired network on the topology/vlan.
C64 topoWireStatMulticastRxPkts	1.3.6.1.4.1.4329.15.3.4.2.3.1.7	Counter64	read-only	Number of multicast frames received unencapsulated from the wired network on the topology/vlan.
C64 topoWireStatBroadcastTxPkts	1.3.6.1.4.1.4329.15.3.4.2.3.1.8	Counter64	read-only	Number of broadcast frames transmitted unencapsulated to the wired network on the topology/vlan.
C64 topoWireStatBroadcastRxPkts	1.3.6.1.4.1.4329.15.3.4.2.3.1.9	Counter64	read-only	Number of broadcast frames received unencapsulated from the wired network on the topology/vlan.
C64 topoWireStatFrameChkSeqErrors	1.3.6.1.4.1.4329.15.3.4.2.3.1.10	Counter64	read-only	Number of unencapsulated frames with checksum errors received from the wired network on the topology/vlan.
C64 topoWireStatFrameTooLongErrors	1.3.6.1.4.1.4329.15.3.4.2.3.1.11	Counter64	read-only	Number of unencapsulated frames with length longer than permitted received from the wired network on the topology/vlan.
topoCompleteStatTable	1.3.6.1.4.1.4329.15.3.4.2.4		not-accessible	The table contains statistics describing traffic transmitted and received for each topology on both the wired side and the wireless side.
topoCompleteStatEntry	1.3.6.1.4.1.4329.15.3.4.2.4.1		not-accessible	Statistics describing traffic transmitted and received on a single topology on both the wired side and the wireless side.
STR topoCompleteStatName	1.3.6.1.4.1.4329.15.3.4.2.4.1.1	DisplayString	read-only	Topology name.
C64 topoCompleteStatTxPkts	1.3.6.1.4.1.4329.15.3.4.2.4.1.2	Counter64	read-only	Number of packets transmitted to the wired and wireless networks on the topology/vlan.
C64 topoCompleteStatRxPkts	1.3.6.1.4.1.4329.15.3.4.2.4.1.3	Counter64	read-only	Number of packets received from the wired and wireless networks on the topology/vlan.
C64 topoCompleteStatTxOctets	1.3.6.1.4.1.4329.15.3.4.2.4.1.4	Counter64	read-only	Number of octets transmitted in frames to the wired and wireless networks on the topology/vlan.
C64 topoCompleteStatRxOctets	1.3.6.1.4.1.4329.15.3.4.2.4.1.5	Counter64	read-only	Number of octets received in frames from the wired and wireless networks on the topology/vlan.
C64 topoCompleteStatMulticastTxPkts	1.3.6.1.4.1.4329.15.3.4.2.4.1.6	Counter64	read-only	Number of multicast frames transmitted to the wired and wireless networks on the topology/vlan.
C64 topoCompleteStatMulticastRxPkts	1.3.6.1.4.1.4329.15.3.4.2.4.1.7	Counter64	read-only	Number of multicast frames received from the wired and wireless networks on the topology/vlan.
C64 topoCompleteStatBroadcastTxPkts	1.3.6.1.4.1.4329.15.3.4.2.4.1.8	Counter64	read-only	Number of broadcast frames transmitted to the wired and wireless networks on the topology/vlan.
C64 topoCompleteStatBroadcastRxPkts	1.3.6.1.4.1.4329.15.3.4.2.4.1.9	Counter64	read-only	Number of broadcast frames received from the wired and wireless networks on the topology/vlan.
C64 topoCompleteStatFrameChkSeqErrors	1.3.6.1.4.1.4329.15.3.4.2.4.1.10	Counter64	read-only	Number of frames with checksum errors received from the wired and wireless networks on the topology/vlan.
C64 topoCompleteStatFrameTooLongErrors	1.3.6.1.4.1.4329.15.3.4.2.4.1.11	Counter64	read-only	Number of oversized frames received from the wired and wireless networks on the topology/vlan.
accessPoints	1.3.6.1.4.1.4329.15.3.5
apConfigObjects	1.3.6.1.4.1.4329.15.3.5.1
I32 apCount	1.3.6.1.4.1.4329.15.3.5.1.1	Integer32	read-only	The count of currently configured AccessPoints associated with this WirelessController.
apTable	1.3.6.1.4.1.4329.15.3.5.1.2		not-accessible	Contains a list of all configured APs associated with the Wireless Controller.
apEntry	1.3.6.1.4.1.4329.15.3.5.1.2.1		not-accessible	Configuration information for an access point.
I32 apIndex	1.3.6.1.4.1.4329.15.3.5.1.2.1.1	Integer32	read-write	Table index for the access point.
STR apName	1.3.6.1.4.1.4329.15.3.5.1.2.1.2	DisplayString	read-write	Access Point's name.
STR apDesc	1.3.6.1.4.1.4329.15.3.5.1.2.1.3	DisplayString	read-write	Text description of the AP.
OCT apSerialNumber	1.3.6.1.4.1.4329.15.3.5.1.2.1.4	OCTET STRING	read-only	16-character serial number of the AccessPoint.
NUM apPortifIndex	1.3.6.1.4.1.4329.15.3.5.1.2.1.5	InterfaceIndex	read-write	ifIndex of the physical port to which this AP is assigned.
NUM apWiredIfIndex	1.3.6.1.4.1.4329.15.3.5.1.2.1.6	InterfaceIndex	read-write	ifIndex of the wired interface on the AP.
OCT apSoftwareVersion	1.3.6.1.4.1.4329.15.3.5.1.2.1.7	OCTET STRING	read-only	Software version currently installed on the AP.
OID apSpecific	1.3.6.1.4.1.4329.15.3.5.1.2.1.8	OBJECT IDENTIFIER	read-only	A link back to the OID under the hiPathWirelessProducts branch that identifies the specific version of this AP.
T/F apBroadcastDisassociate	1.3.6.1.4.1.4329.15.3.5.1.2.1.9	TruthValue	read-write	True indicates that the AP should broadcast disassociation requests, False indicates unicast.
ROW apRowStatus	1.3.6.1.4.1.4329.15.3.5.1.2.1.10	RowStatus	read-write	RowStatus for the apTable.
I32 apVlanID	1.3.6.1.4.1.4329.15.3.5.1.2.1.11	Integer32	read-write	VLAN tag for the packets trasmitted to/from Access Point. Value ranges: (-1) it is not tagged, zero(0) means reserved, 1-4094 tag value.
INT apIpAssignmentType	1.3.6.1.4.1.4329.15.3.5.1.2.1.12	INTEGER	read-write	IP address assignment type, dhcp(1) = uses DHCP to obtain IP address, static(2) = static IP address is assigned to the access point.
MAC apIfMAC	1.3.6.1.4.1.4329.15.3.5.1.2.1.13	MacAddress	read-only	Acess Point's wired interface MAC address.
STR apHwVersion	1.3.6.1.4.1.4329.15.3.5.1.2.1.17	DisplayString	read-write	Text description of Access Point's hardware version.
STR apSwVersion	1.3.6.1.4.1.4329.15.3.5.1.2.1.18	DisplayString	read-write	Text description of Access Point's major software version.
INT apEnvironment	1.3.6.1.4.1.4329.15.3.5.1.2.1.19	INTEGER	read-write	Access Point's environment.
INT apHome	1.3.6.1.4.1.4329.15.3.5.1.2.1.20	INTEGER	read-write	Local session is created when access point registers directly with the controller. Foreign session is mirrored session created via availability feature.
INT apRole	1.3.6.1.4.1.4329.15.3.5.1.2.1.21	INTEGER	read-write	Indicates whether Access Point is a traffic fordwarder, sensor or guardian
INT apState	1.3.6.1.4.1.4329.15.3.5.1.2.1.22	INTEGER	read-write	Active means that access point has registered with this controller at some point of time and still has active connection with this controller. This variable has meaning in the context of the controller that query is done. Inactive mean access point has lost the connection with this controller.
INT apStatus	1.3.6.1.4.1.4329.15.3.5.1.2.1.23	INTEGER	read-write	Registration state for the access point at the time of query, approved(1) means the registration was completed, pending(2) means access point has registered but waiting manual approval from admin.
G32 apPollTimeout	1.3.6.1.4.1.4329.15.3.5.1.2.1.24	Gauge32	read-write	Duration after which the access point's connection to controller is considered has been lost if polling fails.
G32 apPollInterval	1.3.6.1.4.1.4329.15.3.5.1.2.1.25	Gauge32	read-write	Interval between each poll sent to the controller.
INT apTelnetAccess	1.3.6.1.4.1.4329.15.3.5.1.2.1.26	INTEGER	read-write	Indicates whether telnet access is enabled/disabled. This value only applys to AP26xx, W788, W786 and AP4102x APs. 1 : Enabled. 2 : Disabled. 3 : Telnet is not supported.
T/F apMaintainClientSession	1.3.6.1.4.1.4329.15.3.5.1.2.1.27	TruthValue	read-write	If true, Access Point maintains client's session in the event of poll failure.
T/F apRestartServiceContAbsent	1.3.6.1.4.1.4329.15.3.5.1.2.1.28	TruthValue	read-write	If true, Access Point restarts the service in the absence of controller.
STR apHostname	1.3.6.1.4.1.4329.15.3.5.1.2.1.29	DisplayString	read-only	Hostname assigned to Access Point.
STR apLocation	1.3.6.1.4.1.4329.15.3.5.1.2.1.30	DisplayString	read-write	Text identifying location of the access point.
U32 apStaticMTUsize	1.3.6.1.4.1.4329.15.3.5.1.2.1.31	Unsigned32	read-write	Configured MTU size for the access point. Access point will use the lower value of MTU size between statically configured MTU size and dynamically learned MTU size.
I32 apSiteID	1.3.6.1.4.1.4329.15.3.5.1.2.1.32	Integer32	read-write	The site ID, as defined in siteTable, that this AP is member of. The value of -1 indicates that AP is not member of any site.
STR apZone	1.3.6.1.4.1.4329.15.3.5.1.2.1.33	DisplayString	read-write	The Zone to which the Access Point belongs.
T/F apLLDP	1.3.6.1.4.1.4329.15.3.5.1.2.1.34	TruthValue	read-write	Enable or disable broadcasting of LLDP information by the wireless AP.
T/F apSSHAccess	1.3.6.1.4.1.4329.15.3.5.1.2.1.35	TruthValue	read-write	Enable or Disable SSH access to the Wireless AP. This value only applys to AP36xx, AP37xx, W788C and W786C APs.
INT apLEDMode	1.3.6.1.4.1.4329.15.3.5.1.2.1.36	INTEGER	read-write	LED status field for the Access Point. off(0): LED is set to off for the AP. wdsSignalStrength(1): LED conveys the strength of the singal, for the details please refer to user manual. indentify(2): Can be used to lacate the AP by making AP to flashing LED repeatedly. normal(3): This indicates AP's normal operational mode.
T/F apLocationbasedService	1.3.6.1.4.1.4329.15.3.5.1.2.1.37	TruthValue	read-write	Enable or disable the AeroScout or Ekahau location-based service for the Wireless AP.
T/F apSecureTunnel	1.3.6.1.4.1.4329.15.3.5.1.2.1.38	TruthValue	read-write	Enable or disable Secure Tunnel between Ap and Controller
T/F apEncryptCntTraffic	1.3.6.1.4.1.4329.15.3.5.1.2.1.39	TruthValue	read-write	Enable or disable encrypt of control traffic between AP & Controller. This value has meaning only if apSecureTunnel is enabled.
T/F apMICErrorWarning	1.3.6.1.4.1.4329.15.3.5.1.2.1.40	TruthValue	read-write	Enable or disable MIC error warning generation.
INT apSecureDataTunnelType	1.3.6.1.4.1.4329.15.3.5.1.2.1.41	INTEGER	read-write	secure data tunnel status between controller and acesss point. disable(0): disable encryption of control and data traffic between AP & Controller. encryptControlTraffic(1): encrypt control traffic between AP & Controller. encryptControlDataTraffic(2): encrypt control and data traffic between AP & Controller. debugMode(3): preserve keys without encryption.
T/F apIPMulticastAssembly	1.3.6.1.4.1.4329.15.3.5.1.2.1.42	TruthValue	read-write	Enable or disable fragmentation/reassembly of the IP Multicast frames transmitted over the tunnel between AP and Controller. When set to true, an IP Multicast frame larger than the tunnel MTU will be fragmented when it is placed into the WASSP tunnel and reassembled on the receiving end of the tunnel before being forwarded to the clients.
INT apSSHConnection	1.3.6.1.4.1.4329.15.3.5.1.2.1.43	INTEGER	read-write	Enable or Disable SSH access to the Wireless AP. This value only applys to AP36xx, AP37xx, W788C and W786C APs. 1 : Enabled. 2 : Disabled. 3 : SSH is not supported.
apRadioTable	1.3.6.1.4.1.4329.15.3.5.1.3		not-accessible	Table access point radio configuration information.
apRadioEntry	1.3.6.1.4.1.4329.15.3.5.1.3.1		not-accessible	Configuration information for a radio on the access point.
INT apRadioFrequency	1.3.6.1.4.1.4329.15.3.5.1.3.1.1	INTEGER	read-only	The frequency of the radio as supported by the hardware. Supported frequencies are either of 2.5Ghz or 5.0Ghz.
U32 apRadioNumber	1.3.6.1.4.1.4329.15.3.5.1.3.1.2	Unsigned32	read-only	Access point radios are numbered from 1 in increasing order. This numbering is limited in the context of AP. This field returns the radio number of the AP indexed by apIndex.
INT apRadioType	1.3.6.1.4.1.4329.15.3.5.1.3.1.3	INTEGER	read-write	Indicates the type of radio (a, a/n, a/c, n-strict, c-strict, b, g, b/g, or b/g/n) as it is configured.
BIT apRadioProtocol	1.3.6.1.4.1.4329.15.3.5.1.3.1.4	Bits	read-write	Enumerates the possible types of 802.11 radio protocols.
radioVNSTable	1.3.6.1.4.1.4329.15.3.5.1.4		not-accessible	Table of VNSs the radio is participating in.
radioVNSEntry	1.3.6.1.4.1.4329.15.3.5.1.4.1		not-accessible	Information for a single VNS entry.
NUM radioIfIndex	1.3.6.1.4.1.4329.15.3.5.1.4.1.1	InterfaceIndex	read-write	Radio participating in the VNS.
NUM vnsIfIndex	1.3.6.1.4.1.4329.15.3.5.1.4.1.2	InterfaceIndex	read-write	ifIndex for the VNS the radio is participating.
ROW radioVNSRowStatus	1.3.6.1.4.1.4329.15.3.5.1.4.1.3	RowStatus	read-write	RowStatus for the radioVNSTable.
T/F apFastFailoverEnable	1.3.6.1.4.1.4329.15.3.5.1.5	TruthValue	read-write	True indicates that Fast Failover feature is enabled at AP.
I32 apLinkTimeout	1.3.6.1.4.1.4329.15.3.5.1.6	Integer32	read-write	Time to deteck link failure. The value is in 1-30 seconds.
apAntennaTable	1.3.6.1.4.1.4329.15.3.5.1.7		not-accessible	Contains a list of antennas configured for each AP associated with the Wireless Controller. All elements in this table are predefined and read-only.
apAntennaEntry	1.3.6.1.4.1.4329.15.3.5.1.7.1		not-accessible	An entry in this table identifying attributes of one antenna for an AP.
U32 apAntennaIndex	1.3.6.1.4.1.4329.15.3.5.1.7.1.1	Unsigned32	not-accessible	Index of an antenna inside an AP.
STR apAntennanName	1.3.6.1.4.1.4329.15.3.5.1.7.1.2	DisplayString	read-only	Textual description identifying the antenna.
STR apAntennaType	1.3.6.1.4.1.4329.15.3.5.1.7.1.3	DisplayString	read-write	Textual description of antenna type selected for that antenna.
apRadioAntennaTable	1.3.6.1.4.1.4329.15.3.5.1.8		not-accessible	Contains a list of Radio configured for each AP associated with the Wireless Controller. All elements in this table are predefined and read-only.
apRadioAntennaEntry	1.3.6.1.4.1.4329.15.3.5.1.8.1		not-accessible	An entry in this table identifying attributes of one radio for an AP.
STR apRadioAntennaType	1.3.6.1.4.1.4329.15.3.5.1.8.1.3	DisplayString	read-only	Textual description of antenna type selected for that radio.
U32 apRadioAntennaModel	1.3.6.1.4.1.4329.15.3.5.1.8.1.4	Unsigned32	read-only	Antenna type. 0 indicates internal antenna. 1 indicates no antenna. Other value indicates specific external antenna type.
I32 apRadioAttenuation	1.3.6.1.4.1.4329.15.3.5.1.8.1.5	Integer32	read-write	Cumulative attenuation (in dB) of all components (cables, attenuators) between the radio port and the antenna. A professional installer must configure this value so it does not violate country regulations and must verify that it reflects the actual installed components. If this field value is set to -1, then this radio does not support the attenuation configuration.
apStatsObjects	1.3.6.1.4.1.4329.15.3.5.2
I32 apActiveCount	1.3.6.1.4.1.4329.15.3.5.2.1	Integer32	read-only	The count of active AccessPoints associated with this WirelessController.
apStatsTable	1.3.6.1.4.1.4329.15.3.5.2.2		not-accessible	Table of statistics for the access points.
apStatsEntry	1.3.6.1.4.1.4329.15.3.5.2.2.1		not-accessible	Statistics for an access point.
C64 apInUcastPkts	1.3.6.1.4.1.4329.15.3.5.2.2.1.1	Counter64	read-only	Number of unicast packets from wireless-to-wired network.
C64 apInNUcastPkts	1.3.6.1.4.1.4329.15.3.5.2.2.1.2	Counter64	read-only	Number of non-unicast packets from wireless-to-wired network.
C64 apInOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.3	Counter64	read-only	Number of octets from wireless-to-wired network.
C64 apInErrors	1.3.6.1.4.1.4329.15.3.5.2.2.1.4	Counter64	read-only	Number of error packets from wireless-to-wired network.
C64 apInDiscards	1.3.6.1.4.1.4329.15.3.5.2.2.1.5	Counter64	read-only	Number of discarded packets from wireless-to-wired network.
C64 apOutUcastPkts	1.3.6.1.4.1.4329.15.3.5.2.2.1.6	Counter64	read-only	Number of unicast packets from wired-to-wireless network.
C64 apOutNUcastPkts	1.3.6.1.4.1.4329.15.3.5.2.2.1.7	Counter64	read-only	Number of non-unicast packets from wired-to-wireless network.
C64 apOutOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.8	Counter64	read-only	Number of octets from wired-to-wireless network.
C64 apOutErrors	1.3.6.1.4.1.4329.15.3.5.2.2.1.9	Counter64	read-only	Number of error packets from wired-to-wireless network.
C64 apOutDiscards	1.3.6.1.4.1.4329.15.3.5.2.2.1.10	Counter64	read-only	Number of discarded packets from wired-to-wireless network.
TIK apUpTime	1.3.6.1.4.1.4329.15.3.5.2.2.1.11	TimeTicks	read-only	The time (in hundredths of a second) since the management portion of the access point was last re-initialized.
INT apCredentialType	1.3.6.1.4.1.4329.15.3.5.2.2.1.12	INTEGER	read-only	Supported certificate type used by AP for commnuication. none(0) = not supported, TLS(1) = Trasport Layer Security (TLS), PEAP(2) = Protected Extensible Authentication Protocol, all(2) = supports all supported EAP.
TIK apCertificateExpiry	1.3.6.1.4.1.4329.15.3.5.2.2.1.13	TimeTicks	read-only	The number of timeticks from January, 1st, 1970 to the date when the certificate expires (issued certificate no longer is valid).
U32 apStatsMuCounts	1.3.6.1.4.1.4329.15.3.5.2.2.1.14	Unsigned32	read-only	Number of MUs currently associated with this AP.
TIK apStatsSessionDuration	1.3.6.1.4.1.4329.15.3.5.2.2.1.15	TimeTicks	read-only	Elapse time since the access point's session has started.
U32 apTotalStationsA	1.3.6.1.4.1.4329.15.3.5.2.2.1.16	Unsigned32	read-only	Number of MUs that are currently associated to this AP using dot11 connection mode 'a'.
U32 apTotalStationsB	1.3.6.1.4.1.4329.15.3.5.2.2.1.17	Unsigned32	read-only	Number of MUs that are currently associated to this AP using dot11 connection mode 'b'.
U32 apTotalStationsG	1.3.6.1.4.1.4329.15.3.5.2.2.1.18	Unsigned32	read-only	Number of MUs that are currently associated to this AP using dot11 connection mode 'g'.
U32 apTotalStationsN50	1.3.6.1.4.1.4329.15.3.5.2.2.1.19	Unsigned32	read-only	Number of MUs that are currently associated to this AP using dot11 connection mode 'n 5.0 Ghz'.
U32 apTotalStationsN24	1.3.6.1.4.1.4329.15.3.5.2.2.1.20	Unsigned32	read-only	Number of MUs that are currently associated to this AP using dot11 connection mode 'n 2.4 Ghz'.
U32 apInvalidPolicyCount	1.3.6.1.4.1.4329.15.3.5.2.2.1.21	Unsigned32	read-only	Number of invalid role has been assigned to the AP
U32 apInterfaceMTU	1.3.6.1.4.1.4329.15.3.5.2.2.1.22	Unsigned32	read-only	The AP's configured ethernet interface MTU size in bytes.
U32 apEffectiveTunnelMTU	1.3.6.1.4.1.4329.15.3.5.2.2.1.23	Unsigned32	read-only	The AP Effective Tunnel MTU determines the maximum length of the frames that can be tunnelled without fragmentation, after subtracting the tunnel headers (WASSP and IPSEC). The AP Effective Tunnel MTU is determined for each AP tunnel as minimum between the Static MTU (configurable) and Dynamic MTU (learned from the ICMP path discovery).
U32 apTotalStationsAC	1.3.6.1.4.1.4329.15.3.5.2.2.1.24	Unsigned32	read-only	Number of MUs that are currently associated to this AP using dot11ac connection mode.
C64 apTotalStationsAInOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.25	Counter64	read-only	Number of octets from client to AP for clients using protocol 802.11a.
C64 apTotalStationsAOutOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.26	Counter64	read-only	Number of octets from AP to client for clients using protocol 802.11a.
C64 apTotalStationsBInOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.27	Counter64	read-only	Number of octets from client to AP for clients using protocol 802.11b.
C64 apTotalStationsBOutOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.28	Counter64	read-only	Number of octets from AP to client for clients using protocol 802.11b.
C64 apTotalStationsGInOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.29	Counter64	read-only	Number of octets from client to AP for clients using protocol 802.11g.
C64 apTotalStationsGOutOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.30	Counter64	read-only	Number of octets from AP to client for clients using protocol 802.11g.
C64 apTotalStationsN50InOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.31	Counter64	read-only	Number of octets from client to AP for clients using protocol 802.11n (5Ghz).
C64 apTotalStationsN50OutOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.32	Counter64	read-only	Number of octets from AP to client for clients using protocol 802.11n (5Ghz).
C64 apTotalStationsN24InOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.33	Counter64	read-only	Number of octets from client to AP for clients using protocol 802.11n (2.4Ghz).
C64 apTotalStationsN24OutOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.34	Counter64	read-only	Number of octets from AP to client for clients using protocol 802.11n (2.4Ghz).
C64 apTotalStationsACInOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.35	Counter64	read-only	Number of octets from client to AP for clients using protocol 802.11ac.
C64 apTotalStationsACOutOctets	1.3.6.1.4.1.4329.15.3.5.2.2.1.36	Counter64	read-only	Number of octets from AP to client for clients using protocol 802.11ac.
C32 apRegistrationRequests	1.3.6.1.4.1.4329.15.3.5.2.3	Counter32	read-only	Total registration request have been received by all access points since last reboot.
apRadioStatusTable	1.3.6.1.4.1.4329.15.3.5.2.4		not-accessible	Table of radio configuration attributes that the AP can change dynamically. It contains one entry for each radio of each active AP.
apRadioStatusEntry	1.3.6.1.4.1.4329.15.3.5.2.4.1		not-accessible	The configuration attributes of one AP radio that the AP can change dynamically.
U32 apRadioStatusChannel	1.3.6.1.4.1.4329.15.3.5.2.4.1.1	Unsigned32	read-only	The lowest 20 MHz channel of the 20/40/80 MHz wide channel on which the radio is operating. This can be different from the administratively configured channel as a result of the AP complying with regulatory requirements like DFS or adapting to the RF environment (e.g. DCS). If this field value is set to 0, then this means this radio is off or this AP is in Guardian mode.
INT apRadioStatusChannelWidth	1.3.6.1.4.1.4329.15.3.5.2.4.1.2	INTEGER	read-only	Maximum width of the channel being served by the AP's radio. The AP may select a different channel width from the administratively configured width in order to comply with regulatory requirements and the current RF environment.
U32 apRadioStatusChannelOffset	1.3.6.1.4.1.4329.15.3.5.2.4.1.3	Unsigned32	read-only	This is the offset (in 20 MHz channels) of the primary channel from the lowest 20 MHz channel within an aggregated channel. The offset can be 0 if the primary channel is the same as the lowest channel or it can be 1,2 or 3 depending on the aggregate channel width. The AP may select a different channel width from the administratively configured width in order to comply with regulatory requirements and the current RF environment.
apPerformanceReportByRadioTable	1.3.6.1.4.1.4329.15.3.5.2.5		not-accessible	Table of AP performance statistics by radio that the AP can change dynamically. It contains one entry for each radio of each active AP.
apPerformanceReportByRadioEntry	1.3.6.1.4.1.4329.15.3.5.2.5.1		not-accessible	The AP radio performance statistics of one AP radio.
I32 apRadioIndex	1.3.6.1.4.1.4329.15.3.5.2.5.1.1	Integer32	not-accessible	Index of an radio inside an AP.
G32 apPerfRadioPrevPeakChannelUtilization	1.3.6.1.4.1.4329.15.3.5.2.5.1.2	Gauge32	read-only	Peak channel utilization in % from last 15 minute interval.
G32 apPerfRadioCurPeakChannelUtilization	1.3.6.1.4.1.4329.15.3.5.2.5.1.3	Gauge32	read-only	Peak channel utilization in % of current 15 minute interval.
NUM apPerfRadioAverageChannelUtilization	1.3.6.1.4.1.4329.15.3.5.2.5.1.4	HundredthOfGauge32	read-only	Running average of channel utilization in hundredth of a %.
G32 apPerfRadioCurrentChannelUtilization	1.3.6.1.4.1.4329.15.3.5.2.5.1.5	Gauge32	read-only	Channel utilization in % from latest statistics from AP.
G32 apPerfRadioPrevPeakRSS	1.3.6.1.4.1.4329.15.3.5.2.5.1.6	Gauge32	read-only	Peak RSS in dBm from last 15 minute interval. Value of -100 means this field is not available.
G32 apPerfRadioCurPeakRSS	1.3.6.1.4.1.4329.15.3.5.2.5.1.7	Gauge32	read-only	Peak RSS in dBm of current 15 minute interval. Value of -100 means this field is not available.
NUM apPerfRadioAverageRSS	1.3.6.1.4.1.4329.15.3.5.2.5.1.8	HundredthOfInt32	read-only	Running average of RSS in hundredth of a dBm. Value of -10000 means this field is not available.
G32 apPerfRadioCurrentRSS	1.3.6.1.4.1.4329.15.3.5.2.5.1.9	Gauge32	read-only	RSS in dBm from latest statistics from AP. Value of -100 means this field is not available.
G32 apPerfRadioPrevPeakSNR	1.3.6.1.4.1.4329.15.3.5.2.5.1.10	Gauge32	read-only	Peak SNR in dB from last 15 minute interval. Value of -100 means this field is not available.
G32 apPerfRadioCurPeakSNR	1.3.6.1.4.1.4329.15.3.5.2.5.1.11	Gauge32	read-only	Peak SNR in dB of current 15 minute interval. Value of -100 means this field is not available.
NUM apPerfRadioAverageSNR	1.3.6.1.4.1.4329.15.3.5.2.5.1.12	HundredthOfInt32	read-only	Running average of SNR in hundredth of a dB. Value of -10000 means this field is not available.
G32 apPerfRadioCurrentSNR	1.3.6.1.4.1.4329.15.3.5.2.5.1.13	Gauge32	read-only	SNR in dB from latest statistics from AP. Value of -100 means this field is not available.
NUM apPerfRadioPrevPeakPktRetx	1.3.6.1.4.1.4329.15.3.5.2.5.1.14	HundredthOfGauge64	read-only	Peak packet retransmissions in hundredth of pps from last 15 minute interval.
NUM apPerfRadioCurPeakPktRetx	1.3.6.1.4.1.4329.15.3.5.2.5.1.15	HundredthOfGauge64	read-only	Peak packet retransmissions in hundredth of pps of current 15 minute interval.
NUM apPerfRadioAveragePktRetx	1.3.6.1.4.1.4329.15.3.5.2.5.1.16	HundredthOfGauge64	read-only	Running average of packet retransmissions in hundredth of pps.
NUM apPerfRadioCurrentPktRetx	1.3.6.1.4.1.4329.15.3.5.2.5.1.17	HundredthOfGauge64	read-only	Packet retransmissions in hundredth of pps from latest statistics from AP.
C64 apPerfRadioPktRetx	1.3.6.1.4.1.4329.15.3.5.2.5.1.18	Counter64	read-only	Running counter of number of packet retransmissions.
apAccessibilityTable	1.3.6.1.4.1.4329.15.3.5.2.6		not-accessible	A table showing the rate of associations, reassociations and deauthentications/dissassociations from each AP radio. The table contains one row per radio per active AP.
apAccessibilityEntry	1.3.6.1.4.1.4329.15.3.5.2.6.1		not-accessible	The accessibility statistics of one AP radio.
NUM apAccPrevPeakAssocReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.1	HundredthOfGauge64	read-only	Peak number of association requests in hundredth of requests per second received by AP from last 15 minute interval.
NUM apAccCurPeakAssocReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.2	HundredthOfGauge64	read-only	Peak number of association requests in hundredth of requests per second received by AP of current 15 minute interval.
NUM apAccAverageAssocReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.3	HundredthOfGauge64	read-only	Running average of association requests in hundredth of requests per second received by an AP radio.
NUM apAccCurrentAssocReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.4	HundredthOfGauge64	read-only	Association requests in hundredth of requests per second from latest statistics from AP.
C64 apAccAssocReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.5	Counter64	read-only	Running counter of association requests.
NUM apAccPrevPeakReassocReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.6	HundredthOfGauge64	read-only	Peak number of re-association requests in hundredth of requests per second received by an AP radio from last 15 minute interval.
NUM apAccCurPeakReassocReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.7	HundredthOfGauge64	read-only	Peak number of re-association requests in hundredth of requests per second received by an AP radio of current 15 minute interval.
NUM apAccAverageReassocReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.8	HundredthOfGauge64	read-only	Running average of re-association requests in hundredth of requests per second received by an AP radio.
NUM apAccCurrentReassocReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.9	HundredthOfGauge64	read-only	Re-association requests in hundredth of requests per second received by an AP radio from latest statistics from AP.
C64 apAccReassocReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.10	Counter64	read-only	Running counter of re-association requests received by an AP radio.
NUM apAccPrevPeakDisassocDeauthReqTx	1.3.6.1.4.1.4329.15.3.5.2.6.1.11	HundredthOfGauge64	read-only	Peak number of disassociation/deauthentication requests in hundredth of requests per second transmitted by an AP radio from last 15 minute interval.
NUM apAccCurPeakDisassocDeauthReqTx	1.3.6.1.4.1.4329.15.3.5.2.6.1.12	HundredthOfGauge64	read-only	Peak number of disassociation/deauthentication requests in hundredth of requests per second transmitted by an AP radio of current 15 minute interval.
NUM apAccAverageDisassocDeauthReqTx	1.3.6.1.4.1.4329.15.3.5.2.6.1.13	HundredthOfGauge64	read-only	Running average of disassociation/deauthentication requests in hundredth of requests per second transmitted by an AP radio.
NUM apAccCurrentDisassocDeauthReqTx	1.3.6.1.4.1.4329.15.3.5.2.6.1.14	HundredthOfGauge64	read-only	Disassociation/deauthentication requests in hundredth of requests per second transmitted by an AP radio from latest statistics from AP.
C64 apAccDisassocDeauthReqTx	1.3.6.1.4.1.4329.15.3.5.2.6.1.15	Counter64	read-only	Running counter of disassociation/deauthentication requests transmitted by an AP radio.
NUM apAccPrevPeakDisassocDeauthReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.16	HundredthOfGauge64	read-only	Peak number of disassociation/deauthentication requests in hundredth of requests per second received by an AP radio from last 15 minute interval.
NUM apAccCurPeakDisassocDeauthReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.17	HundredthOfGauge64	read-only	Peak number of disassociation/deauthentication requests in hundredth of requests per second received by an AP radio of current 15 minute interval.
NUM apAccAverageDisassocDeauthReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.18	HundredthOfGauge64	read-only	Running average of disassociation/deauthentication requests in hundredth of requests per second received by an AP radio.
NUM apAccCurrentDisassocDeauthReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.19	HundredthOfGauge64	read-only	Disassociation/deauthentication requests in hundredth of requests per second received by an AP radio from latest statistics from AP.
C64 apAccDisassocDeauthReqRx	1.3.6.1.4.1.4329.15.3.5.2.6.1.20	Counter64	read-only	Running counter of disassociation/deauthentication requests received by an AP radio.
apPerformanceReportbyRadioAndWlanTable	1.3.6.1.4.1.4329.15.3.5.2.7		not-accessible	Table of AP performance statistics by AP, AP radio and WLAN.
apPerformanceReportbyRadioAndWlanEntry	1.3.6.1.4.1.4329.15.3.5.2.7.1		not-accessible	The AP performance statistics of one AP radio and WLAN.
G32 apPerfWlanPrevPeakClientsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.1	Gauge32	read-only	Peak clients per second from last 15 minute interval.
G32 apPerfWlanCurPeakClientsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.2	Gauge32	read-only	Peak clients per second of current 15 minute interval.
NUM apPerfWlanAverageClientsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.3	HundredthOfGauge32	read-only	Running average of clients in hundredth of clients per second.
G32 apPerfWlanCurrentClientsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.4	Gauge32	read-only	Clients per second from latest statistics from AP.
NUM apPerfWlanPrevPeakULOctetsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.5	HundredthOfGauge64	read-only	Peak uplink octets in hundredth of octets per second from last 15 minute interval.
NUM apPerfWlanCurPeakULOctetsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.6	HundredthOfGauge64	read-only	Peak uplink octets in hundredth of octets per second of current 15 minute interval.
NUM apPerfWlanAverageULOctetsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.7	HundredthOfGauge64	read-only	Running average of uplink hundredth of octets per second.
NUM apPerfWlanCurrentULOctetsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.8	HundredthOfGauge64	read-only	Uplink octets in hundredth of octets per second from latest statistics from AP.
C64 apPerfWlanULOctets	1.3.6.1.4.1.4329.15.3.5.2.7.1.9	Counter64	read-only	Running counter of uplink octets per second.
NUM apPerfWlanPrevPeakULPktsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.10	HundredthOfGauge64	read-only	Peak uplink packets in hundredth of packets per second from last 15 minute interval.
NUM apPerfWlanCurPeakULPktsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.11	HundredthOfGauge64	read-only	Peak uplink packets in hundredth of packets per second of current 15 minute interval.
NUM apPerfWlanAverageULPktsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.12	HundredthOfGauge64	read-only	Running average of uplink packets in hundredth of packets per second.
NUM apPerfWlanCurrentULPktsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.13	HundredthOfGauge64	read-only	Uplink packets in hundredth of packets per second from latest statistics from AP.
C64 apPerfWlanULPkts	1.3.6.1.4.1.4329.15.3.5.2.7.1.14	Counter64	read-only	Running counter of uplink packets per second.
NUM apPerfWlanPrevPeakDLOctetsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.15	HundredthOfGauge64	read-only	Peak downlink octets in hundredth of octets per second from last 15 minute interval.
NUM apPerfWlanCurPeakDLOctetsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.16	HundredthOfGauge64	read-only	Peak downlink octets in hundredth of octets per second of current 15 minute interval.
NUM apPerfWlanAverageDLOctetsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.17	HundredthOfGauge64	read-only	Running average of downlink octets in hundredth of octets per second.
NUM apPerfWlanCurrentDLOctetsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.18	HundredthOfGauge64	read-only	Downlink octets in hundredth octets per second from latest statistics from AP.
C64 apPerfWlanDLOctets	1.3.6.1.4.1.4329.15.3.5.2.7.1.19	Counter64	read-only	Running counter of downlink octets per second.
NUM apPerfWlanPrevPeakDLPktsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.20	HundredthOfGauge64	read-only	Peak downlink packets in hundredth of packets per second from last 15 minute interval.
NUM apPerfWlanCurPeakDLPktsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.21	HundredthOfGauge64	read-only	Peak downlink packets in hundredth of packets per second of current 15 minute interval.
NUM apPerfWlanAverageDLPktsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.22	HundredthOfGauge64	read-only	Running average of downlink packets in hundredth of packets per second.
NUM apPerfWlanCurrentDLPktsPerSec	1.3.6.1.4.1.4329.15.3.5.2.7.1.23	HundredthOfGauge64	read-only	Downlink packets in hundredth of packets per second from latest statistics from AP.
C64 apPerfWlanDLPkts	1.3.6.1.4.1.4329.15.3.5.2.7.1.24	Counter64	read-only	Running counter of downlink packets per second.
apChannelUtilizationTable	1.3.6.1.4.1.4329.15.3.5.2.8		not-accessible	Table of AP utilization by channel that the AP can change dynamically. It contains one entry for each radio and channel of each active AP.
apChannelUtilizationEntry	1.3.6.1.4.1.4329.15.3.5.2.8.1		not-accessible	The AP performance statistics of one AP radio and channel.
U32 channel	1.3.6.1.4.1.4329.15.3.5.2.8.1.1	Unsigned32	not-accessible	Channel on which utilization is measured.
G32 apChnlUtilPrevPeakUtilization	1.3.6.1.4.1.4329.15.3.5.2.8.1.2	Gauge32	read-only	Peak channel utilization in % from last 15 minute interval.
G32 apChnlUtilCurPeakUtilization	1.3.6.1.4.1.4329.15.3.5.2.8.1.3	Gauge32	read-only	Peak channel utilization in % of current 15 minute interval.
NUM apChnlUtilAverageUtilization	1.3.6.1.4.1.4329.15.3.5.2.8.1.4	HundredthOfGauge32	read-only	Running average of channel utilization in hundredth of %.
G32 apChnlUtilCurrentUtilization	1.3.6.1.4.1.4329.15.3.5.2.8.1.5	Gauge32	read-only	Channel utilization in % from latest statistics from AP.
apNeighboursTable	1.3.6.1.4.1.4329.15.3.5.2.9		not-accessible	A table showing the BSSID, RSS, operating radio channel and detailed information of a nearby AP. The table contains one row per nearby AP per radio per active AP.
apNeighboursEntry	1.3.6.1.4.1.4329.15.3.5.2.9.1		not-accessible	The configuration attributes of one nearby AP.
U32 nearbyApIndex	1.3.6.1.4.1.4329.15.3.5.2.9.1.1	Unsigned32	not-accessible	Nearby AP index.
STR nearbyApInfo	1.3.6.1.4.1.4329.15.3.5.2.9.1.2	DisplayString	read-only	Detailed information of a nearby AP.
OCT nearbyApBSSID	1.3.6.1.4.1.4329.15.3.5.2.9.1.3	OCTET STRING	read-only	The BSSID of a nearby AP.
STR nearbyApChannel	1.3.6.1.4.1.4329.15.3.5.2.9.1.4	DisplayString	read-only	The operating radio channel of a nearby AP.
I32 nearbyApRSS	1.3.6.1.4.1.4329.15.3.5.2.9.1.5	Integer32	read-only	The Received Signal Strength of a nearby AP.
sensorManagement	1.3.6.1.4.1.4329.15.3.5.3
STR tftpSever	1.3.6.1.4.1.4329.15.3.5.3.1	DisplayString	read-write	TFTP server that sensor image resides.
STR imagePath26xx	1.3.6.1.4.1.4329.15.3.5.3.2	DisplayString	read-write	Path of sensor image on TFTP server.
STR imagePath36xx	1.3.6.1.4.1.4329.15.3.5.3.3	DisplayString	read-write	Path of sensor image on TFTP server.
STR imageVersionOfap26xx	1.3.6.1.4.1.4329.15.3.5.3.4	DisplayString	read-write	Sensor's software version.
STR imageVersionOfngap36xx	1.3.6.1.4.1.4329.15.3.5.3.5	DisplayString	read-write	Sensor's softerware version for Next Generation Access Point.
apRegistration	1.3.6.1.4.1.4329.15.3.5.4
INT apRegSecurityMode	1.3.6.1.4.1.4329.15.3.5.4.1	INTEGER	read-write	Indicates registration mode for an AP. If allowAll(1), then all wireless APs are allowed to register to the controlloer, otherwise only approved APs in 'Approved AP' list are allowed to register to the controller.
U32 apRegDiscoveryRetries	1.3.6.1.4.1.4329.15.3.5.4.2	Unsigned32	read-write	Number of retries for discovery requests from an access point to controller. After these number of retries, the access point will start over again after some arbitrary delays.
U32 apRegDiscoveryInterval	1.3.6.1.4.1.4329.15.3.5.4.3	Unsigned32	read-write	Interval between two consecutive discovery requests from the same access point.
OCT apRegTelnetPassword	1.3.6.1.4.1.4329.15.3.5.4.4	OCTET STRING	read-write	Password used to access an AP via telnet. This field is write-only and read access returns empty string.
OCT apRegSSHPassword	1.3.6.1.4.1.4329.15.3.5.4.5	OCTET STRING	read-write	SSH password used to access an access point. This field is write-only and read access returns empty string.
T/F apRegUseClusterEncryption	1.3.6.1.4.1.4329.15.3.5.4.6	TruthValue	read-write	If this field set to true, then all APs in the cluster use cluster encryption.
OCT apRegClusterSharedSecret	1.3.6.1.4.1.4329.15.3.5.4.7	OCTET STRING	read-write	Password for cluster encryption. This field is write-only and read access returns empty string.
loadBalancing	1.3.6.1.4.1.4329.15.3.5.5
loadGroupTable	1.3.6.1.4.1.4329.15.3.5.5.1		not-accessible	Table of configured load groups for access points. A set of access points can be grouped together and they are identified by unique name. An access point can only be assigned to one group.
loadGroupEntry	1.3.6.1.4.1.4329.15.3.5.5.1.1		not-accessible	An entry containing definition of a load group. There exists two types of load group: client-balancing-group and radio-balancing-group.
U32 loadGroupID	1.3.6.1.4.1.4329.15.3.5.5.1.1.1	Unsigned32	read-only	Internally generated ID for a group and cannot be changed externally.
STR loadGroupName	1.3.6.1.4.1.4329.15.3.5.5.1.1.2	DisplayString	read-write	Unique name assigned to the group.
INT loadGroupType	1.3.6.1.4.1.4329.15.3.5.5.1.1.3	INTEGER	read-write	Type of load balancing this group supports.
INT loadGroupBandPreference	1.3.6.1.4.1.4329.15.3.5.5.1.1.4	INTEGER	read-write	Band preference is enabled for this group if this field is set to true and group type is set to radioBalancing(1).
INT loadGroupLoadControl	1.3.6.1.4.1.4329.15.3.5.5.1.1.5	INTEGER	read-write	Load balancing is enabled for this group if this field is set to true and group type is set to radioBalancing(1).
U32 loadGroupClientCountRadio1	1.3.6.1.4.1.4329.15.3.5.5.1.1.6	Unsigned32	read-write	Maximum number of client on this radio. This field is only applicable to a group with radioBalancing(1) type.
U32 loadGroupClientCountRadio2	1.3.6.1.4.1.4329.15.3.5.5.1.1.7	Unsigned32	read-write	Maximum number of client on this radio. This field is only applicable to a group with radioBalancing(1) type.
INT loadGroupLoadControlEnableR1	1.3.6.1.4.1.4329.15.3.5.5.1.1.8	INTEGER	read-write	If it is enabled then load control is applicable to radio #1 of all access points that are assigned to this load group. This field has meaning only for the load group that is of radioBalancing(1) type.
INT loadGroupLoadControlEnableR2	1.3.6.1.4.1.4329.15.3.5.5.1.1.9	INTEGER	read-write	If it is enabled then load control is applicable to radio #2 of all access points that are assigned to this load group. This field has meaning only for the load group that is of radioBalancing(1) type.
INT loadGroupLoadControlStrictLimitR1	1.3.6.1.4.1.4329.15.3.5.5.1.1.10	INTEGER	read-write	If it is enabled then strict limit for load control is applicable to radio #1 of all access points that are assigned to this load group. This field has meaning only for the load group that is of radioBalancing(1) type.
INT loadGroupLoadControlStrictLimitR2	1.3.6.1.4.1.4329.15.3.5.5.1.1.11	INTEGER	read-write	If it is enabled then strict limit for load control is applicable to radio #2 of all access points that are assigned to this load group. This field has meaning only for the load group that is of radioBalancing(1) type.
loadGrpRadiosTable	1.3.6.1.4.1.4329.15.3.5.5.2		not-accessible	Table of radio assignment to defined load groups.
loadGrpRadiosEntry	1.3.6.1.4.1.4329.15.3.5.5.2.1		not-accessible	Any entry defining radio assignment of AP, identified by apIndex, to a load group identified by loadGroupID.
INT loadGrpRadiosRadio1	1.3.6.1.4.1.4329.15.3.5.5.2.1.2	INTEGER	read-write	If this field is set to 'assigned(1)', then the radio of the AP identified by the apIndex is a member of the load balancing group identified by the loadBlanaceID. For radio blanacing group, either all or none of the radios of a specific AP (indentified by apIndex) are assigned to the load balancing group.
INT loadGrpRadiosRadio2	1.3.6.1.4.1.4329.15.3.5.5.2.1.3	INTEGER	read-write	If this field is set to 'assigned(2)', then the radio of the AP identified by the apIndex is a member of the load balancing group identified by the loadBlanaceID. For radio blanacing group, either all or none of the radios of a specific AP (indentified by apIndex) are assigned to the load balancing group.
loadGrpWlanTable	1.3.6.1.4.1.4329.15.3.5.5.3		not-accessible	Table of WLAN assignment to defined load groups.
loadGrpWlanEntry	1.3.6.1.4.1.4329.15.3.5.5.3.1		not-accessible	An entry defining WLAN, identified by wlanID, assignment to a load group identified by loadGroupID.
T/F loadGrpWlanAssigned	1.3.6.1.4.1.4329.15.3.5.5.3.1.1	TruthValue	read-write	Assignement of WLAN, identified with wlanID, to the load balancing group identified bye loadGroupID.
apMaintenanceCycle	1.3.6.1.4.1.4329.15.3.5.6
INT schedule	1.3.6.1.4.1.4329.15.3.5.6.1	INTEGER	read-write	AP maintenance schedule options. 0 : never perform the maintenance action. 1 : perform the maintenance action every day. 2 : perform the maintenance action every week. 3 : perform the maintenance action every month.
I32 startHour	1.3.6.1.4.1.4329.15.3.5.6.2	Integer32	read-write	Maintenance action starts at this hour of the day.
I32 startMinute	1.3.6.1.4.1.4329.15.3.5.6.3	Integer32	read-write	Maintenance action starts at this minute of the hour.
I32 duration	1.3.6.1.4.1.4329.15.3.5.6.4	Integer32	read-write	Duration of the AP maintenance cycle (how often maintenance is done) in hours.
INT recurrenceDaily	1.3.6.1.4.1.4329.15.3.5.6.5	INTEGER	read-write	This field has meaning only when the maintenance schedule option is set to daily(1). Below is the recurrence option. 0 : every day. 1 : every weekday. 2 : every weekend.
BIT recurrenceWeekly	1.3.6.1.4.1.4329.15.3.5.6.6	Bits	read-write	This field has meaning only when the maintenance schedule option is set to weekly(2). Below are the recurrence options. BIT 0 : Sunday. BIT 1 : Monday. BIT 2 : Tuesday. BIT 3 : Wednesday. BIT 4 : Thursday. BIT 5 : Friday. BIT 6 : Saturday.
BIT recurrenceMonthly	1.3.6.1.4.1.4329.15.3.5.6.7	Bits	read-write	This field has meaning only when the maintenance schedule option is set to monthly(3). Below are the recurrence options. BIT 0 : the first week of the month. BIT 1 : the second week of the month. BIT 2 : the third week of the month. BIT 3 : the fourth week of the month. BIT 4 : the fifth week of the month. BIT 5 : sunday of the week. BIT 6 : monday of the week. BIT 7 : tuesday of the week. BIT 8 : wednesday of the week. BIT 9 : thursday of the week. BIT 10 : friday of the week. BIT 11 : saturday of the week.
BIT apPlatforms	1.3.6.1.4.1.4329.15.3.5.6.8	Bits	read-write	Select which models of the AP platforms to perform the maintenance. BIT 0 : AP2600 platform. BIT 1 : AP2605 platform. BIT 2 : AP2650 platform. BIT 3 : AP4102 platform. BIT 4 : W786 platform. BIT 5 : AP3705 platform. BIT 6 : AP3710 platform. BIT 7 : AP3715 platform. BIT 8 : AP3765 platform. BIT 9 : AP3767 platform. BIT 10 : AP3801 platform. BIT 11 : AP3805 platform. BIT 12 : AP3825 platform. BIT 13 : AP3865 platform. BIT 14 : AP3935 platform. BIT 15 : AP3965 platform. BIT 16 : W78XC platform. BIT 17 : W78XCSFP platform.
mobileUnits	1.3.6.1.4.1.4329.15.3.6
I32 mobileUnitCount	1.3.6.1.4.1.4329.15.3.6.1	Integer32	read-write	Number of clients associated with the controller.
muTable	1.3.6.1.4.1.4329.15.3.6.2		not-accessible	Table of information for clients associated with the EWC.
muEntry	1.3.6.1.4.1.4329.15.3.6.2.1		not-accessible	Information for a client associated with the EWC.
MAC muMACAddress	1.3.6.1.4.1.4329.15.3.6.2.1.1	MacAddress	read-only	Client MAC address.
IP muIPAddress	1.3.6.1.4.1.4329.15.3.6.2.1.2	IpAddress	read-only	Client IP Address.
OCT muUser	1.3.6.1.4.1.4329.15.3.6.2.1.3	OCTET STRING	read-only	Client login name.
T/F muState	1.3.6.1.4.1.4329.15.3.6.2.1.4	TruthValue	read-only	True if the client is authenticated.
OCT muAPSerialNo	1.3.6.1.4.1.4329.15.3.6.2.1.5	OCTET STRING	read-only	Serial Number of the Access Point the client is associated with.
OCT muVnsSSID	1.3.6.1.4.1.4329.15.3.6.2.1.6	OCTET STRING	read-only	SSID of the VNS the client is associated with.
C64 muTxPackets	1.3.6.1.4.1.4329.15.3.6.2.1.7	Counter64	read-only	Number of packets trasmitted to the client.
C64 muRxPackets	1.3.6.1.4.1.4329.15.3.6.2.1.8	Counter64	read-only	Number of packets received from the client.
C64 muTxOctets	1.3.6.1.4.1.4329.15.3.6.2.1.9	Counter64	read-only	Number of octets transmitted to the client.
C64 muRxOctets	1.3.6.1.4.1.4329.15.3.6.2.1.10	Counter64	read-only	Number of octets received from the client.
C64 muDuration	1.3.6.1.4.1.4329.15.3.6.2.1.11	Counter64	read-only	Time client has been associated with the EWC.
STR muAPName	1.3.6.1.4.1.4329.15.3.6.2.1.12	DisplayString	read-only	Name of the Access Point the client is associated with.
STR muTopologyName	1.3.6.1.4.1.4329.15.3.6.2.1.13	DisplayString	read-only	Topology name that the MU is associated with.
STR muPolicyName	1.3.6.1.4.1.4329.15.3.6.2.1.14	DisplayString	read-only	The name of the policy that provides filter for this MU.
STR muDefaultCoS	1.3.6.1.4.1.4329.15.3.6.2.1.15	DisplayString	read-only	The CoS that is applied to the current traffic if the defined rule for the current traffic has not specifically defined any CoS.
INT muConnectionProtocol	1.3.6.1.4.1.4329.15.3.6.2.1.16	INTEGER	read-only	The MU is using this connection protocol for current connection. Symbols notation: n50 = an = n5.0Ghz, n24 = bgn = n2.4Ghz
INT muConnectionCapability	1.3.6.1.4.1.4329.15.3.6.2.1.17	INTEGER	read-only	This field indicates what are the MU connection capability.
U32 muWLANID	1.3.6.1.4.1.4329.15.3.6.2.1.18	Unsigned32	read-only	ID of the WLAN that the MU is associated with.
MAC muBSSIDMac	1.3.6.1.4.1.4329.15.3.6.2.1.19	MacAddress	read-only	Client BSSID MAC address.
BIT muDot11ConnectionCapability	1.3.6.1.4.1.4329.15.3.6.2.1.20	Bits	read-write	This field indicates what are the MU connection capabilities. bit 0 : If this bit is set, the client is capable to tx/rx on A radio. bit 1 : If this bit is set, the client is capable to tx/rx on BG radio. bit 2 : If this bit is set, the client is capable of wpaV1 privacy. bit 3 : If this bit is set, the client is capable of wpaV2 privacy. bit 4 : If this bit is set, the client is capable to comunicate with 1 data stream. bit 5 : If this bit is set, the client is capable to comunicate with 2 data streams. bit 6 : If this bit is set, the client is capable to comunicate with 3 data streams. bit 7 : If this bit is set, the client is capable of Unscheduled automatic power-save delivery (U-APSD) benefits. The voice client can synchronize the transmission and reception of voice frames with the AP. bit 8 : If this bit is set, the client is capable of Unscheduled automatic power-save delivery (U-APSD) benefits. The video client can synchronize the transmission and reception of video frames with the AP. bit 9 : If this bit is set, the client is capable of Unscheduled automatic power-save delivery (U-APSD) benefits. The client can synchronize the transmission and reception in background queue. bit 10 : If this bit is set, the client is capable of Unscheduled automatic power-save delivery (U-APSD) benefits. The client can synchronize the transmission and reception in best effort queue. bit 11 : If this bit is set, the client is capable of Wi-Fi Multimedia(WMM) power save. bit 12 : If this bit is set, the client is capable of 802.11n Greenfield mode. bit 13 : If this bit is set, the client is on fast-transition mode.
muTSPECTable	1.3.6.1.4.1.4329.15.3.6.3		not-accessible	Table of information for Admission Control Statistics by active client.
muTSPECEntry	1.3.6.1.4.1.4329.15.3.6.3.1		not-accessible	Information for Admission Control Statistics by active client.
MAC tspecMuMACAddress	1.3.6.1.4.1.4329.15.3.6.3.1.1	MacAddress	read-only	Client MAC address.
INT tspecAC	1.3.6.1.4.1.4329.15.3.6.3.1.2	INTEGER	read-only	Access Category, such as Best Effort, Background, Voice, Video, and Reserved.
INT tspecDirection	1.3.6.1.4.1.4329.15.3.6.3.1.3	INTEGER	read-only	Traffic direction, such as uplink direction, downlink direction.
OCT tspecApSerialNumber	1.3.6.1.4.1.4329.15.3.6.3.1.4	OCTET STRING	read-only	16-character serial number of the AccessPoint.
IP tspecMuIPAddress	1.3.6.1.4.1.4329.15.3.6.3.1.5	IpAddress	read-only	Client IP Address.
MAC tspecBssMac	1.3.6.1.4.1.4329.15.3.6.3.1.6	MacAddress	read-only	Access Point BSSID.
STR tspecSsid	1.3.6.1.4.1.4329.15.3.6.3.1.7	DisplayString	read-only	VNS SSID.
U32 tspecMDR	1.3.6.1.4.1.4329.15.3.6.3.1.8	Unsigned32	read-only	Mean Data Rate (bytes per second).
U32 tspecNMS	1.3.6.1.4.1.4329.15.3.6.3.1.9	Unsigned32	read-only	Nominal MSDU size (bytes).
U32 tspecSBA	1.3.6.1.4.1.4329.15.3.6.3.1.10	Unsigned32	read-only	Surplus Bandwidth Allowance.
STR tspecDlRate	1.3.6.1.4.1.4329.15.3.6.3.1.11	DisplayString	read-only	Downlink Rate (bytes per second).
STR tspecUlRate	1.3.6.1.4.1.4329.15.3.6.3.1.12	DisplayString	read-only	Uplink Rate (bytes per second).
STR tspecDlViolations	1.3.6.1.4.1.4329.15.3.6.3.1.13	DisplayString	read-only	Downlink Violations (bytes per second).
STR tspecUlViolations	1.3.6.1.4.1.4329.15.3.6.3.1.14	DisplayString	read-only	Uplink Violations (bytes per second).
INT tspecProtocol	1.3.6.1.4.1.4329.15.3.6.3.1.15	INTEGER	read-only	802.11 radio protocol.
INT muACLType	1.3.6.1.4.1.4329.15.3.6.4	INTEGER	read-write	MUs can access EWC by sending association request and providing proper credentials. However, EWC allows creation of a master list of a blacklist or a whitelist group to control such access. There can exist only a blacklist or a whitelist (mutually exclusive) at any time. The list of MUs belonging to such a list is populated in muACLTable. The muACLTable content can be interpreted in conjunction with this field as follows: - blacklist(1): MUs listed in muACLTable cannot access EWC resources. - whitelist(2): Only MUs listed in muACLTable can access EWC resources.
muACLTable	1.3.6.1.4.1.4329.15.3.6.5		not-accessible	Semantics of this list is directly related to muACLType. Access Control List(ACL) is list of MUs and their access rights. An MU can either belong to 'Blacklist', in that case its association request is denied, or it can belong to 'Whitelist', in that case it is allowed to associate to EWC provided having proper credentials.
muACLEntry	1.3.6.1.4.1.4329.15.3.6.5.1		not-accessible	An entry about an MU and its ACL.
MAC muACLMACAddress	1.3.6.1.4.1.4329.15.3.6.5.1.1	MacAddress	read-only	MAC address of MU.
ROW muACLRowStatus	1.3.6.1.4.1.4329.15.3.6.5.1.2	RowStatus	read-create	An MU can either be added or removed to this list, therefore, allowed set values for this field are: createAndGo, destroy.
muAccessListTable	1.3.6.1.4.1.4329.15.3.6.6		not-accessible	Semantics of this list is directly related to muACLType. Access List Control(ACL) list of MUs and their access rights. An MU can either belong to 'Blacklist', in that case its association request is denied, or it can belong to 'Whitelist', in that case it is allowed to associate to EWC provided having proper credentials.
muAccessListEntry	1.3.6.1.4.1.4329.15.3.6.6.1		not-accessible	An entry about about an MU and its ACL.
MAC muAccessListMACAddress	1.3.6.1.4.1.4329.15.3.6.6.1.1	MacAddress	read-only	MAC address of MU.
INT muAccessListBitmaskLength	1.3.6.1.4.1.4329.15.3.6.6.1.2	INTEGER	read-create	Length of bitmask associated to the MAC address in the entry.
ROW muAccessListRowStatus	1.3.6.1.4.1.4329.15.3.6.6.1.3	RowStatus	read-create	An MU can either be added or removed to this list, therefore, allowed set values for this field are: createAndGo, destroy.
associations	1.3.6.1.4.1.4329.15.3.7
I32 assocCount	1.3.6.1.4.1.4329.15.3.7.1	Integer32	read-write	Total number of current client associations to the access point.
assocTable	1.3.6.1.4.1.4329.15.3.7.2		not-accessible	Table of information about clients associated with the access point.
assocEntry	1.3.6.1.4.1.4329.15.3.7.2.1		not-accessible	Information for a single client in the association table.
MAC assocMUMacAddress	1.3.6.1.4.1.4329.15.3.7.2.1.1	MacAddress	read-only	MAC address of the client.
TIK assocStartSysUpTime	1.3.6.1.4.1.4329.15.3.7.2.1.2	TimeTicks	read-only	The system uptime that client became associated with the access point.
C64 assocTxPackets	1.3.6.1.4.1.4329.15.3.7.2.1.3	Counter64	read-only	Nubmer of tx packets to the client.
C64 assocRxPackets	1.3.6.1.4.1.4329.15.3.7.2.1.4	Counter64	read-only	Number of received packets from the client.
C64 assocTxOctets	1.3.6.1.4.1.4329.15.3.7.2.1.5	Counter64	read-only	Number of octets sent to the client.
C64 assocRxOctets	1.3.6.1.4.1.4329.15.3.7.2.1.6	Counter64	read-only	Number of octets received from the client.
I32 assocDuration	1.3.6.1.4.1.4329.15.3.7.2.1.7	Integer32	read-write	Length of time since last association.
NUM assocVnsIfIndex	1.3.6.1.4.1.4329.15.3.7.2.1.8	InterfaceIndex	read-only	Index of VNS to which the MU is associated with.
protocols	1.3.6.1.4.1.4329.15.3.8
wassp	1.3.6.1.4.1.4329.15.3.8.1
logNotifications	1.3.6.1.4.1.4329.15.3.9
LOG logEventSeverityThreshold	1.3.6.1.4.1.4329.15.3.9.1	LogEventSeverity	read-write	Specifies the minimum level at which the SNMP agent will send notifications for log events. I.e., setting this value to 'major' will send notifcations for critical and major log events. Setting the threshold to minor will trap critical, major, and minor events.
LOG logEventSeverity	1.3.6.1.4.1.4329.15.3.9.3	LogEventSeverity	read-only	Contains the severity of the most recently trapped hiPathWirelessLogAlarm notification.
OCT logEventComponent	1.3.6.1.4.1.4329.15.3.9.4	OCTET STRING	read-only	Contains the component which sent the most recently trapped hiPathWirelessLogAlarm notification.
OCT logEventDescription	1.3.6.1.4.1.4329.15.3.9.5	OCTET STRING	read-only	Contains the description of the most recently trapped hiPathWirelessLogAlarm.
NTF hiPathWirelessLogAlarm	1.3.6.1.4.1.4329.15.3.9.6			Components of an alarm.
sites	1.3.6.1.4.1.4329.15.3.10
U32 siteMaxEntries	1.3.6.1.4.1.4329.15.3.10.1	Unsigned32	read-only	The maximum number of entries allowed in the siteTable. This value is platform dependent.
U32 siteNumEntries	1.3.6.1.4.1.4329.15.3.10.2	Unsigned32	read-only	The current number of entries in the siteTable.
U32 siteTableNextAvailableIndex	1.3.6.1.4.1.4329.15.3.10.3	Unsigned32	read-only	This object indicates the numerically lowest available index within this entity, which may be used for the value of siteID in the creation of a new entry in the siteTable. An index is considered available if the index value falls within the range of 1 to siteMaxEntries value and is not being used to index an existing entry in the siteTable contained within this entity. This value should only be considered a guideline for management creation of siteEntries, there is no requirement on management to create entries based upon this index value.
siteTable	1.3.6.1.4.1.4329.15.3.10.4		not-accessible	A site is a logical entity that is constituted by collection of APs, CoS rules, policies, Radius server, WLAN, etc. A site is identified by a unique name.
siteEntry	1.3.6.1.4.1.4329.15.3.10.4.1		not-accessible	Definition of a site.
U32 siteID	1.3.6.1.4.1.4329.15.3.10.4.1.1	Unsigned32	read-only	An unique ID, identifying the site in the context of the controller. The site ID can be an integer value from 1 to the maximum number of APs supported by the EWC.
ROW siteRowStatus	1.3.6.1.4.1.4329.15.3.10.4.1.2	RowStatus	read-create	Row status for the entry.
STR siteName	1.3.6.1.4.1.4329.15.3.10.4.1.3	DisplayString	read-create	Textual description to identify the site in the context of the controller.
T/F siteLocalRadiusAuthentication	1.3.6.1.4.1.4329.15.3.10.4.1.4	TruthValue	read-create	If this value is set to true, then the RADIUS client is on APs, otherwise the RADIUS client is on controller.
STR siteDefaultDNSServer	1.3.6.1.4.1.4329.15.3.10.4.1.5	DisplayString	read-create	If the APs associated to the site uses DHCP, and DHCP server does not assign DNS server, then this entry will be used for that purpose. Otherwise, if AP is configured with static IP address, then this entry will be used for that purpose.
T/F siteEnableSecureTunnel	1.3.6.1.4.1.4329.15.3.10.4.1.6	TruthValue	read-create	If set to true secure communication key sent to APs to be used to encrypt the traffic between APs within the site and the traffic between controller and APs. However, the encryption itself does not take place unless siteEncryptCommAPtoController and/or siteEncryptCommBetweenAPs set to true.
T/F siteEncryptCommAPtoController	1.3.6.1.4.1.4329.15.3.10.4.1.7	TruthValue	read-create	If set to true, communication between APs within the site and the controller are encrypted using defined encyption. For details about encryption type, please refer to user manual.
T/F siteEncryptCommBetweenAPs	1.3.6.1.4.1.4329.15.3.10.4.1.8	TruthValue	read-create	If set to true, communication between APs within the site are encrypted using defined encyption. For details about encryption type, please refer to user manual.
INT siteBandPreferenceEnable	1.3.6.1.4.1.4329.15.3.10.4.1.9	INTEGER	read-create	Enabling/disabling band preference for the site and associated APs. By enabling band preference 11a-capable clients can be moved to 11a radio and relieve the congestion on the 11g radio. Band preference provides radio load balancing between 11g and 11a radios.
INT siteLoadControlEnableR1	1.3.6.1.4.1.4329.15.3.10.4.1.10	INTEGER	read-create	Enabling/disabling load control for the site for this radio. Load control manages the number of clients on the Radio #1 by disallowing additional clients on the radio above the configured radio limit.
INT siteLoadControlEnableR2	1.3.6.1.4.1.4329.15.3.10.4.1.11	INTEGER	read-create	Enabling/disabling load control for the site for this radio. Load control manages the number of clients on the Radio #2 by disallowing additional clients on the radio above the configured radio limit.
U32 siteMaxClientR1	1.3.6.1.4.1.4329.15.3.10.4.1.12	Unsigned32	read-create	Maximum number of clients that are allowed to be associated to this radio (radio #1). If the Load Control is not enabled then the maximum for this radio uses default value.
U32 siteMaxClientR2	1.3.6.1.4.1.4329.15.3.10.4.1.13	Unsigned32	read-create	Maximum number of clients that are allowed to be associated to this radio (radio #2). If the Load Control is not enabled then the maximum for this radio uses default value.
INT siteStrictLimitEnableR1	1.3.6.1.4.1.4329.15.3.10.4.1.14	INTEGER	read-create	Enabling/disabling strict limit of load control for this radio that is assigned to the site. Eanbleing strict limit enforces configured client limit for the radio (radio #1) in any circumstances. Otherwise if this field is disabled then the restriction may not be enforced in all circumstances.
INT siteStrictLimitEnableR2	1.3.6.1.4.1.4329.15.3.10.4.1.15	INTEGER	read-create	Enabling/disabling strict limit of load control for this radio that is assigned to the site. Eanbleing strict limit enforces configured client limit for the radio (radio #2) in any circumstances. Otherwise if this field is disabled then the restriction may not be enforced in all circumstances.
T/F siteReplaceStnIDwithSiteName	1.3.6.1.4.1.4329.15.3.10.4.1.16	TruthValue	read-create	If this value is set to true, then the called station ID will be replaced with the site name.
sitePolicyTable	1.3.6.1.4.1.4329.15.3.10.5		not-accessible	Each site can have zero or more policies assigned to it. All policies associated to a site are pushed to the all APs belonging to the site. This table defines the assignment of various policies to various sites.
sitePolicyEntry	1.3.6.1.4.1.4329.15.3.10.5.1		not-accessible	An entry defining assignment of a policy, identified by sitePolicyID, to a site, identified by siteID.
U32 sitePolicyID	1.3.6.1.4.1.4329.15.3.10.5.1.1	Unsigned32	not-accessible	The policy index, as defined ENTERASYS-POLICY-PROFILE-MIB::etsysPolicyProfileIndex.
INT sitePolicyMember	1.3.6.1.4.1.4329.15.3.10.5.1.2	INTEGER	read-write	Indicates whether the policy associated with this row is a member of the zone identified by zoneID.
siteCosTable	1.3.6.1.4.1.4329.15.3.10.6		not-accessible	Each site can have zero or more CoS assigned to it. All CoS associated to a site are pushed to the all APs belonging to the site. This table defines the assignment of various CoS to various sites.
siteCosEntry	1.3.6.1.4.1.4329.15.3.10.6.1		not-accessible	An entry defining assignment of a CoS, identified by siteCoSID, to a site, identified by siteID.
U32 siteCoSID	1.3.6.1.4.1.4329.15.3.10.6.1.1	Unsigned32	not-accessible	The CoS index, as defined in ENTERASYS-POLICY-PROFILE-MIB::etsysCosIndex.
INT siteCoSMember	1.3.6.1.4.1.4329.15.3.10.6.1.2	INTEGER	read-only	Indicates whether the CoS associated with this row is a member of the site identified by siteID.
siteAPTable	1.3.6.1.4.1.4329.15.3.10.7		not-accessible	A site can have zero or more Access Points(AP) assigned to it. This table defines the assignment of various APs to various sites.
siteAPEntry	1.3.6.1.4.1.4329.15.3.10.7.1		not-accessible	An entry defining assignment of an AP, identified by apIndex, to a site, identified by siteID.
INT siteAPMember	1.3.6.1.4.1.4329.15.3.10.7.1.1	INTEGER	read-write	Indicates whether the AP associated with this row is a member of the site identified by siteID.
siteWlanTable	1.3.6.1.4.1.4329.15.3.10.8		not-accessible	A site can have zero or more WLAN assigned to it. All WLANs that are associated with a site are pushed to the all APs belonging to the site. This table defines the assignment of various WLANs to various sites.
siteWlanEntry	1.3.6.1.4.1.4329.15.3.10.8.1		not-accessible	An entry defining assignment of a WLAN identified by siteWlanID, to a site, identified by siteID.
INT siteWlanApRadioIndex	1.3.6.1.4.1.4329.15.3.10.8.1.1	INTEGER	not-accessible	Description.
INT siteWlanApRadioAssigned	1.3.6.1.4.1.4329.15.3.10.8.1.2	INTEGER	read-write	Description.
widsWips	1.3.6.1.4.1.4329.15.3.11
INT mitigatorAnalysisEngine	1.3.6.1.4.1.4329.15.3.11.1	INTEGER	read-write	Mitigator analysis engine can be enabled/disabled using this variable. All mitigator related objects, objects defined in widsWips subtree, can only be accessed using SNMPv3 provided this variable is set to enable(1) on behalf of users with privacy.
U32 scanGroupMaxEntries	1.3.6.1.4.1.4329.15.3.11.2	Unsigned32	read-only	Maximum number of scan groups that can be created on the device.
U32 scanGroupsCurrentEntries	1.3.6.1.4.1.4329.15.3.11.3	Unsigned32	read-only	Number of scan groups currently have been created on the device.
U32 activeThreatsCounts	1.3.6.1.4.1.4329.15.3.11.4	Unsigned32	read-only	Number of currently active threats that have been detected.
U32 friendlyAPCounts	1.3.6.1.4.1.4329.15.3.11.5	Unsigned32	read-only	Number of friendly access points that have been discovered at this point.
U32 uncategorizedAPCounts	1.3.6.1.4.1.4329.15.3.11.6	Unsigned32	read-only	Number of uncategorized access points that have been discovered. This value refers to current number not the historical value.
widsWipsEngineTable	1.3.6.1.4.1.4329.15.3.11.11		not-accessible	Table of Mitigators defined on set of controllers each identified by widsWipsEngineControllerIPAddress.
widsWipsEngineEntry	1.3.6.1.4.1.4329.15.3.11.11.1		not-accessible	One entry in this table identifying a mitigator engine in a defined controller identified by IP address, widsWipsEngineControllerIPAddress.
ROW widsWipsEngineRowStatus	1.3.6.1.4.1.4329.15.3.11.11.1.1	RowStatus	read-create	RowStatus for creation/deletion of mitigator engine row.
IP widsWipsEngineControllerIPAddress	1.3.6.1.4.1.4329.15.3.11.11.1.2	IpAddress	read-create	Ip address of the controller that the defined mitigator in this row will run on.
INT widsWipsEnginePollInterval	1.3.6.1.4.1.4329.15.3.11.11.1.3	INTEGER	read-create	Poll interval in seconds between successive keep alive messages between this controller and the mitigator engine to monitor status of mitigator engine.
INT widsWipsEnginePollRetry	1.3.6.1.4.1.4329.15.3.11.11.1.4	INTEGER	read-create	Number of consecutive retries of failed contact to a mitigator agent before declaring mitigator engine dead.
inServiceScanGroupTable	1.3.6.1.4.1.4329.15.3.11.12		not-accessible	In service scan group enables the subsystem simultaneously scan for threats and performs wireless bridging based on 37xx-based APs. The threats are discovered and identified in the deployment environment and then classified for further actions.
inServiceScanGroupEntry	1.3.6.1.4.1.4329.15.3.11.12.1		not-accessible	An entry in this table that defines attributes of a in-service scan group.
U32 scanGroupProfileID	1.3.6.1.4.1.4329.15.3.11.12.1.1	Unsigned32	not-accessible	A internally unique identifier for a scan group. Each scan group is indexed by this value.
STR inSrvScanGrpName	1.3.6.1.4.1.4329.15.3.11.12.1.2	DisplayString	read-create	Textual description identifying the scan group.
INT inSrvScanGrpSecurityThreats	1.3.6.1.4.1.4329.15.3.11.12.1.3	INTEGER	read-create	Enable/disable security engine to scan for threats.
INT inSrvScanGrpMaxConcurrentAttacksPerAP	1.3.6.1.4.1.4329.15.3.11.12.1.4	INTEGER	read-create	Max number of concurrent attacks per AP
BIT inSrvScanGrpCounterMeasuresType	1.3.6.1.4.1.4329.15.3.11.12.1.5	Bits	read-create	bit 0: Setting this bit prevents authorized stations from roaming to external honeypot APs. bit 1: Setting this bit prevents authorized stations from roaming to friendly APs. bit 2: Setting this bit prevents any station from using an internal honeypot AP. bit 3: Setting this bit prevents any station from using a spoofed AP. bit 4: Setting this bit drops frames in a controlled fashion during a flood attack. bit 5: Setting this bit removes network access from clients originating DoS attacks. bit 6: Setting this bit prevents any station from using an ad hoc mode device. bit 7: Setting this bit prevents any station from using a rogue AP.
BIT inSrvScanGrpScan2400MHzSelection	1.3.6.1.4.1.4329.15.3.11.12.1.6	Bits	read-create	bit 0: by setting this bit scanning is performed on 2412 MHz frequency channel bit 1: by setting this bit scanning is performed on 2417 MHz frequency channel bit 2: by setting this bit scanning is performed on 2422 MHz frequency channel bit 3: by setting this bit scanning is performed on 2427 MHz frequency channel bit 4: by setting this bit scanning is performed on 2432 MHz frequency channel bit 5: by setting this bit scanning is performed on 2437 MHz frequency channel bit 6: by setting this bit scanning is performed on 2442 MHz frequency channel bit 7: by setting this bit scanning is performed on 2447 MHz frequency channel bit 8: by setting this bit scanning is performed on 2452 MHz frequency channel bit 9: by setting this bit scanning is performed on 2457 MHz frequency channel bit 10: by setting this bit scanning is performed on 2462 MHz frequency channel bit 11: by setting this bit scanning is performed on 2467 MHz frequency channel bit 12: by setting this bit scanning is performed on 2472 MHz frequency channel bit 13: by setting this bit scanning is performed on 2484 MHz frequency channel
BIT inSrvScanGrpScan5GHzSelection	1.3.6.1.4.1.4329.15.3.11.12.1.7	Bits	read-create	bit 0: by setting this bit scanning is performed on 5040 MHz frequency channel bit 1: by setting this bit scanning is performed on 5060 MHz frequency channel bit 2: by setting this bit scanning is performed on 5080 MHz frequency channel bit 3: by setting this bit scanning is performed on 5180 MHz frequency channel bit 4: by setting this bit scanning is performed on 5200 MHz frequency channel bit 5: by setting this bit scanning is performed on 5220 MHz frequency channel bit 6: by setting this bit scanning is performed on 5240 MHz frequency channel bit 7: by setting this bit scanning is performed on 5260 MHz frequency channel bit 8: by setting this bit scanning is performed on 5280 MHz frequency channel bit 9: by setting this bit scanning is performed on 5300 MHz frequency channel bit 10: by setting this bit scanning is performed on 5320 MHz frequency channel bit 11: by setting this bit scanning is performed on 5500 MHz frequency channel bit 12: by setting this bit scanning is performed on 5520 MHz frequency channel bit 13: by setting this bit scanning is performed on 5540 MHz frequency channel bit 14: by setting this bit scanning is performed on 5560 MHz frequency channel bit 15: by setting this bit scanning is performed on 5580 MHz frequency channel bit 16: by setting this bit scanning is performed on 5600 MHz frequency channel bit 17: by setting this bit scanning is performed on 5620 MHz frequency channel bit 18: by setting this bit scanning is performed on 5640 MHz frequency channel bit 19: by setting this bit scanning is performed on 5660 MHz frequency channel bit 20: by setting this bit scanning is performed on 5680 MHz frequency channel bit 21: by setting this bit scanning is performed on 5700 MHz frequency channel bit 22: by setting this bit scanning is performed on 5745 MHz frequency channel bit 23: by setting this bit scanning is performed on 5765 MHz frequency channel bit 24: by setting this bit scanning is performed on 5785 MHz frequency channel bit 25: by setting this bit scanning is performed on 5805 MHz frequency channel bit 26: by setting this bit scanning is performed on 5825 MHz frequency channel bit 27: by setting this bit scanning is performed on 4920 MHz frequency channel bit 28: by setting this bit scanning is performed on 4940 MHz frequency channel bit 29: by setting this bit scanning is performed on 4960 MHz frequency channel bit 30: by setting this bit scanning is performed on 4980 MHz frequency channel
I32 inSrvScanGrpblockAdHocClientsPeriod	1.3.6.1.4.1.4329.15.3.11.12.1.8	Integer32	read-create	Number of seconds removing network access to the clients that are in ad hoc mode.
INT inSrvScanGrpClassifySourceIF	1.3.6.1.4.1.4329.15.3.11.12.1.9	INTEGER	read-create	This variable allows to enable/disable classify sources of interference
ROW inSrvScanGrpRowStatus	1.3.6.1.4.1.4329.15.3.11.12.1.10	RowStatus	read-create	RowStatus field for creation/deletion or changing row status.
INT inSrvScanGrpDetectRogueAP	1.3.6.1.4.1.4329.15.3.11.12.1.11	INTEGER	read-create	This enables/disables rogue AP detection.
I32 inSrvScanGrpListeningPort	1.3.6.1.4.1.4329.15.3.11.12.1.12	Integer32	read-write	This OID represents the UDP port number that APs are to listen on while performing rogue AP detection. It has meaning only when inSrvScanGrpDetectRogueAP is enabled.
outOfServiceScanGroupTable	1.3.6.1.4.1.4329.15.3.11.13		not-accessible	Out of service scan group is used to collect and classify various wireless identifiers that are discovered in the deployment environment. Legacy APs (26xx-based, 36xx-based) can participate in this subsystem if they are configured for out-of-service scanning. The new APs, based on 37xx architecture, can also participate in this subsystem.
outOfServiceScanGroupEntry	1.3.6.1.4.1.4329.15.3.11.13.1		not-accessible	An entry in this table that defines attributes of a out-of-service scan group.
STR outOfSrvScanGrpName	1.3.6.1.4.1.4329.15.3.11.13.1.1	DisplayString	read-create	Human readable textual description identifying scan group.
INT outOfSrvScanGrpRadio	1.3.6.1.4.1.4329.15.3.11.13.1.2	INTEGER	read-create	Radio selection for the scan group. Selected radio will be used in sacn group.
INT outOfSrvScanGrpChannelList	1.3.6.1.4.1.4329.15.3.11.13.1.3	INTEGER	read-create	Identifying the channel(s) which will be used for the defined scan group.
INT outOfSrvScanGrpScanType	1.3.6.1.4.1.4329.15.3.11.13.1.4	INTEGER	read-create	This field allows to select the type of scanning, active/passive, this scan group will be executing.
INT outOfSrvScanGrpChannelDwellTime	1.3.6.1.4.1.4329.15.3.11.13.1.5	INTEGER	read-create	Dwell time in mili-second for performing scanning.
INT outOfSrvScanGrpScanTimeInterval	1.3.6.1.4.1.4329.15.3.11.13.1.6	INTEGER	read-create	Time interval between two sucssive scanning performed for this scan group.
INT outOfSrvScanGrpSecurityScan	1.3.6.1.4.1.4329.15.3.11.13.1.7	INTEGER	read-create	This field allows to enable/disable security Scan.
INT outOfSrvScanGrpScanActivity	1.3.6.1.4.1.4329.15.3.11.13.1.8	INTEGER	read-create	Scaning can be started or stopped using this field.
I32 outOfSrvScanGrpScanRowStatus	1.3.6.1.4.1.4329.15.3.11.13.1.9	Integer32	read-create	RowStatus field for the entry.
scanGroupAPAssignmentTable	1.3.6.1.4.1.4329.15.3.11.14		not-accessible	The list of APs that have been assigned to a particular scan group, which could include in-service and out-of-service scanning groups.
scanGroupAPAssignmentEntry	1.3.6.1.4.1.4329.15.3.11.14.1		not-accessible	An entry in this table defining an AP assignment to a group, identified by scanGroupProfileID.
OCT scanGroupAPAssignApSerial	1.3.6.1.4.1.4329.15.3.11.14.1.1	OCTET STRING	read-only	Unique string of characters, a 16-character long, serial number of an access point.
STR scanGroupAPAssignGroupName	1.3.6.1.4.1.4329.15.3.11.14.1.2	DisplayString	read-only	Human readable textual description identifying scan group.
STR scanGroupAPAssignName	1.3.6.1.4.1.4329.15.3.11.14.1.3	DisplayString	read-only	Access Point (AP) name associated to this scan group.
INT scanGroupAPAssignRadio1	1.3.6.1.4.1.4329.15.3.11.14.1.4	INTEGER	read-write	This field allows the radio #1 of the AP to be turned on/off. this field has meaning only the AP assigned to legacy (outOfScan) scan profile
INT scanGroupAPAssignRadio2	1.3.6.1.4.1.4329.15.3.11.14.1.5	INTEGER	read-write	This field allows the radio #2 of the AP to be turned on/off. this field has meaning only the AP assigned to legacy (outOfScan) scan profile
INT scanGroupAPAssignInactiveAP	1.3.6.1.4.1.4329.15.3.11.14.1.6	INTEGER	read-write	This field allows to set the AP as active/inactive in scanning activities.
INT scanGroupAPAssignAllowScanning	1.3.6.1.4.1.4329.15.3.11.14.1.7	INTEGER	read-write	Setting scanning to active/inactive using this AP.
INT scanGroupAPAssignAllowSpectrumAnalysis	1.3.6.1.4.1.4329.15.3.11.14.1.8	INTEGER	read-write	Setting spectrum analysis to active/inactive using this AP.
IP scanGroupAPAssignControllerIPAddress	1.3.6.1.4.1.4329.15.3.11.14.1.9	IpAddress	read-write	The IP address of the controller to which the AP is connected currently.
BIT scanGroupAPAssignFordwardingService	1.3.6.1.4.1.4329.15.3.11.14.1.10	Bits	read-only	This OID lists the types of forwarding services that each Guardian is assigned to. A Guardian will revert to providing these services when it is removed from the Guardian role. The meanings of the individual flags are: bit 0: Set if this AP is a member of a site. bit 1: Set if this AP is assigned to a load group. bit 2: Set if this AP is assigned to at least one WLAN service. This OID is only relevant to APs in the Guardian role.
scanAPTable	1.3.6.1.4.1.4329.15.3.11.15		not-accessible	Table of sacn APs on each collector. This table can be viewed only in v3 mode when the mitigator analys engine is enabled.
scanAPEntry	1.3.6.1.4.1.4329.15.3.11.15.1		not-accessible	An entry in this table identifying one access point.
IP scanAPControllerIPAddress	1.3.6.1.4.1.4329.15.3.11.15.1.1	IpAddress	read-only	IP address of the controller on which the scanning executed.
OCT scanAPSerialNumber	1.3.6.1.4.1.4329.15.3.11.15.1.2	OCTET STRING	read-only	Serial number of the access point, 16-character human readable text, that is assigned to this group.
STR scanAPAcessPointName	1.3.6.1.4.1.4329.15.3.11.15.1.3	DisplayString	read-create	Name of the access point belonging to this group.
ROW scanAPRowStatus	1.3.6.1.4.1.4329.15.3.11.15.1.4	RowStatus	read-create	Row status for the entry.
STR scanAPProfileName	1.3.6.1.4.1.4329.15.3.11.15.1.5	DisplayString	read-create	Name of the scan profile to which this access point is assigned.
INT scanAPProfileType	1.3.6.1.4.1.4329.15.3.11.15.1.6	INTEGER	read-create	inServiceScan(1): access point is performed In service Scan. guardianScan(2): access point is performed Guardian Scan. outOfServiceScan(3): access point is performed out of service Scan(Legacy Scan).
friendlyAPTable	1.3.6.1.4.1.4329.15.3.11.16		not-accessible	List of Access Points that have been categorized as not being any threat to the wireless network that is managed by EWC. This table can be viewed only in v3 mode when the mitigator analys engine is enabled.
friendlyAPEntry	1.3.6.1.4.1.4329.15.3.11.16.1		not-accessible	An entry in this table identifying an access points and some of its attributes.
MAC friendlyAPMacAddress	1.3.6.1.4.1.4329.15.3.11.16.1.1	MacAddress	read-write	Ethernet MAC address of the access point.
STR friendlyAPSSID	1.3.6.1.4.1.4329.15.3.11.16.1.2	DisplayString	read-write	SSID broadcasted by the access point.
STR friendlyAPDescription	1.3.6.1.4.1.4329.15.3.11.16.1.3	DisplayString	read-write	Textual description that is used to identify the access point.
STR friendlyAPManufacturer	1.3.6.1.4.1.4329.15.3.11.16.1.4	DisplayString	read-only	Textual description identifying the access point manufacturer.
uncategorizedAPTable	1.3.6.1.4.1.4329.15.3.11.17		not-accessible	List of APs that have not been categorized either as friendly, threat or authorized.
uncategorizedAPEntry	1.3.6.1.4.1.4329.15.3.11.17.1		not-accessible	An entry about an AP in this table.
MAC uncategorizedAPMAC	1.3.6.1.4.1.4329.15.3.11.17.1.1	MacAddress	not-accessible	MAC address of access point.
STR uncategorizedAPDescption	1.3.6.1.4.1.4329.15.3.11.17.1.2	DisplayString	read-only	Textual description of access point.
STR uncategorizedAPManufacturer	1.3.6.1.4.1.4329.15.3.11.17.1.3	DisplayString	read-only	Access point manufacturer.
INT uncategorizedAPClassify	1.3.6.1.4.1.4329.15.3.11.17.1.4	INTEGER	read-write	By setting this field, access point can be reclassified and moved to different group.
STR uncategorizedAPSSID	1.3.6.1.4.1.4329.15.3.11.17.1.5	DisplayString	read-only	SSID broadcasted by the access point.
authorizedAPTable	1.3.6.1.4.1.4329.15.3.11.18		not-accessible	List of authorized access point.
authorizedAPEntry	1.3.6.1.4.1.4329.15.3.11.18.1		not-accessible	An entry in this table describing an authorized AP.
MAC authorizedAPMAC	1.3.6.1.4.1.4329.15.3.11.18.1.1	MacAddress	not-accessible	MAC address of access point.
STR authorizedAPDescription	1.3.6.1.4.1.4329.15.3.11.18.1.2	DisplayString	read-create	Discription of the access point.
STR authorizedAPManufacturer	1.3.6.1.4.1.4329.15.3.11.18.1.3	DisplayString	read-create	Access point's manufacturer. This field is cannot be set and it is deduced by MAC addressed.
INT authorizedAPClassify	1.3.6.1.4.1.4329.15.3.11.18.1.4	INTEGER	read-create	By setting this field, access point can be reclassified and moved to different group.
ROW authorizedAPRowStatus	1.3.6.1.4.1.4329.15.3.11.18.1.5	RowStatus	read-create	Action permitted are 'delete/add' row.
prohibitedAPTable	1.3.6.1.4.1.4329.15.3.11.19		not-accessible	List of prohibited access points.
prohibitedAPEntry	1.3.6.1.4.1.4329.15.3.11.19.1		not-accessible	An entry in this table describing an access point.
MAC prohibitedAPMAC	1.3.6.1.4.1.4329.15.3.11.19.1.1	MacAddress	not-accessible	MAC address of access point.
INT prohibitedAPCategory	1.3.6.1.4.1.4329.15.3.11.19.1.2	INTEGER	read-create	The category the access point in this row belongs to.
STR prohibitedAPDescription	1.3.6.1.4.1.4329.15.3.11.19.1.3	DisplayString	read-create	Description of the access point.
STR prohibitedAPManufacturer	1.3.6.1.4.1.4329.15.3.11.19.1.4	DisplayString	read-create	Access point's manufacturer. This field is cannot be set and it is deduced by MAC addressed.
INT prohibitedAPClassify	1.3.6.1.4.1.4329.15.3.11.19.1.5	INTEGER	read-create	By setting this field, access point can be reclassified and moved to different group.
ROW prohibitedAPRowStatus	1.3.6.1.4.1.4329.15.3.11.19.1.6	RowStatus	read-create	Action permitted are 'delete/add' row.
dedicatedScanGroupTable	1.3.6.1.4.1.4329.15.3.11.20		not-accessible	dedicated scan group enables the subsystem full time scan for threats based on 37xx-based APs. The threats are discovered and identified in the deployment environment and then classified for further actions.
dedicatedScanGroupEntry	1.3.6.1.4.1.4329.15.3.11.20.1		not-accessible	An entry in this table that defines attributes of a dedicated scan group.
STR dedicatedScanGrpName	1.3.6.1.4.1.4329.15.3.11.20.1.1	DisplayString	read-create	Textual description identifying the scan group.
INT dedicatedScanGrpSecurityThreats	1.3.6.1.4.1.4329.15.3.11.20.1.2	INTEGER	read-create	Enable/disable security engine to scan for threats.
I32 dedicatedScanGrpMaxConcurrentAttacksPerAP	1.3.6.1.4.1.4329.15.3.11.20.1.3	Integer32	read-create	Max number of concurrent attacks per AP
BIT dedicatedScanGrpCounterMeasures	1.3.6.1.4.1.4329.15.3.11.20.1.4	Bits	read-create	bit 0: Setting this bit prevents authorized stations from roaming to external honeypot APs. bit 1: Setting this bit prevents authorized stations from roaming to friendly APs. bit 2: Setting this bit prevents any station from using an internal honeypot AP. bit 3: Setting this bit prevents any station from using a spoofed AP. bit 4: Setting this bit drops frames in a controlled fashion during a flood attack. bit 5: Setting this bit removes network access from clients originating DoS attacks. bit 6: Setting this bit prevents any station from using an ad hoc mode device. bit 7: Setting this bit prevents any station from using a rogue AP.
BIT dedicatedScanGrpScan2400MHzFreq	1.3.6.1.4.1.4329.15.3.11.20.1.5	Bits	read-create	bit 0: by setting this bit scanning is performed on 2412 MHz frequency channel bit 1: by setting this bit scanning is performed on 2417 MHz frequency channel bit 2: by setting this bit scanning is performed on 2422 MHz frequency channel bit 3: by setting this bit scanning is performed on 2427 MHz frequency channel bit 4: by setting this bit scanning is performed on 2432 MHz frequency channel bit 5: by setting this bit scanning is performed on 2437 MHz frequency channel bit 6: by setting this bit scanning is performed on 2442 MHz frequency channel bit 7: by setting this bit scanning is performed on 2447 MHz frequency channel bit 8: by setting this bit scanning is performed on 2452 MHz frequency channel bit 9: by setting this bit scanning is performed on 2457 MHz frequency channel bit 10: by setting this bit scanning is performed on 2462 MHz frequency channel bit 11: by setting this bit scanning is performed on 2467 MHz frequency channel bit 12: by setting this bit scanning is performed on 2472 MHz frequency channel bit 13: by setting this bit scanning is performed on 2484 MHz frequency channel
BIT dedicatedScanGrpScan5GHzFreq	1.3.6.1.4.1.4329.15.3.11.20.1.6	Bits	read-create	bit 0: by setting this bit scanning is performed on 5040 MHz frequency channel bit 1: by setting this bit scanning is performed on 5060 MHz frequency channel bit 2: by setting this bit scanning is performed on 5080 MHz frequency channel bit 3: by setting this bit scanning is performed on 5180 MHz frequency channel bit 4: by setting this bit scanning is performed on 5200 MHz frequency channel bit 5: by setting this bit scanning is performed on 5220 MHz frequency channel bit 6: by setting this bit scanning is performed on 5240 MHz frequency channel bit 7: by setting this bit scanning is performed on 5260 MHz frequency channel bit 8: by setting this bit scanning is performed on 5280 MHz frequency channel bit 9: by setting this bit scanning is performed on 5300 MHz frequency channel bit 10: by setting this bit scanning is performed on 5320 MHz frequency channel bit 11: by setting this bit scanning is performed on 5500 MHz frequency channel bit 12: by setting this bit scanning is performed on 5520 MHz frequency channel bit 13: by setting this bit scanning is performed on 5540 MHz frequency channel bit 14: by setting this bit scanning is performed on 5560 MHz frequency channel bit 15: by setting this bit scanning is performed on 5580 MHz frequency channel bit 16: by setting this bit scanning is performed on 5600 MHz frequency channel bit 17: by setting this bit scanning is performed on 5620 MHz frequency channel bit 18: by setting this bit scanning is performed on 5640 MHz frequency channel bit 19: by setting this bit scanning is performed on 5660 MHz frequency channel bit 20: by setting this bit scanning is performed on 5680 MHz frequency channel bit 21: by setting this bit scanning is performed on 5700 MHz frequency channel bit 22: by setting this bit scanning is performed on 5745 MHz frequency channel bit 23: by setting this bit scanning is performed on 5765 MHz frequency channel bit 24: by setting this bit scanning is performed on 5785 MHz frequency channel bit 25: by setting this bit scanning is performed on 5805 MHz frequency channel bit 26: by setting this bit scanning is performed on 5825 MHz frequency channel bit 27: by setting this bit scanning is performed on 4920 MHz frequency channel bit 28: by setting this bit scanning is performed on 4940 MHz frequency channel bit 29: by setting this bit scanning is performed on 4960 MHz frequency channel bit 30: by setting this bit scanning is performed on 4980 MHz frequency channel
I32 dedicatedScanGrpBlockAdHocPeriod	1.3.6.1.4.1.4329.15.3.11.20.1.7	Integer32	read-create	Number of seconds removing network access to the clients that are in ad hoc mode.
INT dedicatedScanGrpClassifySourceIF	1.3.6.1.4.1.4329.15.3.11.20.1.8	INTEGER	read-create	This variable allows to enable/disable classify sources of interference
ROW dedicatedScanGrpRowStatus	1.3.6.1.4.1.4329.15.3.11.20.1.9	RowStatus	read-create	RowStatus field for creation/deletion or changing row status.
INT dedicatedScanGrpDetectRogueAP	1.3.6.1.4.1.4329.15.3.11.20.1.10	INTEGER	read-create	This enables/disables rogue AP detection.
I32 dedicatedScanGrpListeningPort	1.3.6.1.4.1.4329.15.3.11.20.1.11	Integer32	read-create	This variable has meaning only when dedicatedScanGrpDetectRogueAP is enabled. The port number is the port for listening for rogue AP detection.
widsWipsReport	1.3.6.1.4.1.4329.15.3.11.30
activeThreatTable	1.3.6.1.4.1.4329.15.3.11.30.1		not-accessible	List of active threats that have been discovered to this point of time.
activeThreatEntry	1.3.6.1.4.1.4329.15.3.11.30.1.1		not-accessible	An entry in this table describing an idividual threat charactersitics and attributes.
U32 activeThreatIndex	1.3.6.1.4.1.4329.15.3.11.30.1.1.1	Unsigned32	not-accessible	Internally generated number without any significat meaning except used as indexing in this table.
STR activeThreatCategory	1.3.6.1.4.1.4329.15.3.11.30.1.1.2	DisplayString	read-only	Textual description describing the type of the threat.
MAC activeThreatDeviceMAC	1.3.6.1.4.1.4329.15.3.11.30.1.1.3	MacAddress	read-only	MAC address of the device that the threat appears to be originated.
STR activeThreatDateTime	1.3.6.1.4.1.4329.15.3.11.30.1.1.4	DisplayString	read-only	Date and time the threat was discovered.
INT activeThreatCounterMeasure	1.3.6.1.4.1.4329.15.3.11.30.1.1.5	INTEGER	read-only	Counter measure has been taken to tackle the threat.
STR activeThreatAPName	1.3.6.1.4.1.4329.15.3.11.30.1.1.6	DisplayString	read-only	Name of the access point.
STR activeThreatRSS	1.3.6.1.4.1.4329.15.3.11.30.1.1.7	DisplayString	read-only	Signal strength of the device considered to be a threat.
STR activeThreatExtraDetails	1.3.6.1.4.1.4329.15.3.11.30.1.1.8	DisplayString	read-only	Extra comments related to the threat.
STR activeThreatThreat	1.3.6.1.4.1.4329.15.3.11.30.1.1.9	DisplayString	read-only	Textual description of the threat.
countermeasureAPTable	1.3.6.1.4.1.4329.15.3.11.30.2		not-accessible	List of APs engaged in countermeasure activities to thwart coming threats.
countermeasureAPEntry	1.3.6.1.4.1.4329.15.3.11.30.2.1		not-accessible	An entry in this table identifying an AP engaged in countermeasure activities.
U32 countermeasureAPThreatIndex	1.3.6.1.4.1.4329.15.3.11.30.2.1.1	Unsigned32	not-accessible	Internally generated index of the access point taking part in countermeasure.
STR countermeasureAPSerial	1.3.6.1.4.1.4329.15.3.11.30.2.1.2	DisplayString	read-only	Serial number of the access point taking part in countermeasure.
STR countermeasureAPName	1.3.6.1.4.1.4329.15.3.11.30.2.1.3	DisplayString	read-only	Name of the access point taking part in countermeasure.
STR countermeasureAPThreatCategory	1.3.6.1.4.1.4329.15.3.11.30.2.1.4	DisplayString	read-only	Textual description of the threat category that countermeasure action is aimed at.
STR countermeasureAPCountermeasure	1.3.6.1.4.1.4329.15.3.11.30.2.1.5	DisplayString	read-only	Countermeasure has been taken to thwart the threat.
STR countermeasureAPTime	1.3.6.1.4.1.4329.15.3.11.30.2.1.6	DisplayString	read-only	The time that the countermeasure has started.
blacklistedClientTable	1.3.6.1.4.1.4329.15.3.11.30.3		not-accessible	List of clients that have been blacklisted due to preceived threats they may pose to the safe functioning of the operating network.
blacklistedClientEntry	1.3.6.1.4.1.4329.15.3.11.30.3.1		not-accessible	An entry in this table pertaining information about the MU that has been blacklisted.
MAC blacklistedClientMAC	1.3.6.1.4.1.4329.15.3.11.30.3.1.1	MacAddress	read-only	MAC address of the client.
STR blacklistedClientStatTime	1.3.6.1.4.1.4329.15.3.11.30.3.1.2	DisplayString	read-only	The time blacklisting started.
STR blacklistedClientEndTime	1.3.6.1.4.1.4329.15.3.11.30.3.1.3	DisplayString	read-only	The time blacklisting ends.
STR blacklistedClientReason	1.3.6.1.4.1.4329.15.3.11.30.3.1.4	DisplayString	read-only	Reason for blacklisting the client.
threatSummaryTable	1.3.6.1.4.1.4329.15.3.11.30.4		not-accessible	Summary of all threats that have been detected in the network by wireless controller system.
threatSummaryEntry	1.3.6.1.4.1.4329.15.3.11.30.4.1		not-accessible	An entry summarizing statistics about a category of a threat.
U32 threatSummaryIndex	1.3.6.1.4.1.4329.15.3.11.30.4.1.1	Unsigned32	not-accessible	Internally generated index.
STR threatSummaryCategory	1.3.6.1.4.1.4329.15.3.11.30.4.1.2	DisplayString	read-only	Textul description identifying the category of a threat.
U32 threatSummaryActiveThreat	1.3.6.1.4.1.4329.15.3.11.30.4.1.3	Unsigned32	read-only	Counts of threats that are currently active.
U32 threatSummaryHistoricalCounts	1.3.6.1.4.1.4329.15.3.11.30.4.1.4	Unsigned32	read-only	Historical counts of such threat that were detected in the past by the wireless controller system.
apNotifications	1.3.6.1.4.1.4329.15.3.19
INT apEventId	1.3.6.1.4.1.4329.15.3.19.1	INTEGER	read-write	Identifies event associated with AP or AP tunnel: apPollTimeout - an event triggered when the AP disconnects from the controller. apRegister - an event triggered when the AP connects to the controller.
OCT apEventDescription	1.3.6.1.4.1.4329.15.3.19.2	OCTET STRING	read-only	Contains the description of the most recently triggered event.
OCT apEventAPSerialNumber	1.3.6.1.4.1.4329.15.3.19.3	OCTET STRING	read-only	16-character serial number of the AP.
NTF apTunnelAlarm	1.3.6.1.4.1.4329.15.3.19.4			alarm associated with AP and AP interface.
stationSessionNotifications	1.3.6.1.4.1.4329.15.3.20
INT stationEventType	1.3.6.1.4.1.4329.15.3.20.1	INTEGER	read-only	station event type include: registration(0): MU registration. deRegistration(1): MU de-registration. stateChange(2): MU state changed. registrationFailed(3): MU registration failure. roam(4): MU roam. mbaTimeout(5): MU MAC-Based-Authentication time out. mbaAccepted(6): MU MAC-Based-Authentication accepted. mbaRejected(7): MU MAC-Based-Authentication rejected. authorizationChanged(8): MU authorization changed. authentication(9): MU authentication. authenticationFailed(10): MU authentication failure. locationUpdate(11): MU location updated. areaChange(12): MU roamed to other area.
MAC stationMacAddress	1.3.6.1.4.1.4329.15.3.20.2	MacAddress	read-only	MAC address of the station that is the subject of this event report.
IP stationIPAddress	1.3.6.1.4.1.4329.15.3.20.3	IpAddress	read-only	IP address of the station that is the subject of this event report.
STR stationAPName	1.3.6.1.4.1.4329.15.3.20.4	DisplayString	read-only	name of the AP which station associated with
STR stationAPSSID	1.3.6.1.4.1.4329.15.3.20.5	DisplayString	read-only	SSID broadcasted by the access point which station connected to
STR stationDetailEvent	1.3.6.1.4.1.4329.15.3.20.6	DisplayString	read-only	detail description of the station event
STR stationRoamedAPName	1.3.6.1.4.1.4329.15.3.20.7	DisplayString	read-only	name of the access point which station roamed from
STR stationName	1.3.6.1.4.1.4329.15.3.20.8	DisplayString	read-only	name of station
STR stationBSSID	1.3.6.1.4.1.4329.15.3.20.9	DisplayString	read-only	the Mac address of the radio which station connect to
TIK stationEventTimeStamp	1.3.6.1.4.1.4329.15.3.20.10	TimeTicks	read-only	The duration in hundredths of a second from the network agent start time to the time of generation of the station event.
NTF stationEventAlarm	1.3.6.1.4.1.4329.15.3.20.11			A trap describing a significant event that happened to a station during a session on the network. A controller can sees hundreds or even thousands of these events every second.
ADR stationIPv6Address1	1.3.6.1.4.1.4329.15.3.20.12	Ipv6Address	read-only	One of the IPv6 addresses of the station that is the subject of this event report.
ADR stationIPv6Address2	1.3.6.1.4.1.4329.15.3.20.13	Ipv6Address	read-only	One of the IPv6 addresses of the station that is the subject of this event report.
ADR stationIPv6Address3	1.3.6.1.4.1.4329.15.3.20.14	Ipv6Address	read-only	One of the IPv6 addresses of the station that is the subject of this event report.
hiPathWirelessHWCConformance	1.3.6.1.4.1.4329.15.3.30
hiPathWirelessHWCModule	1.3.6.1.4.1.4329.15.3.30.1			Conformance definition for the EWC MIB.
hiPathWirelessHWCGroup	1.3.6.1.4.1.4329.15.3.30.2			Conformance groups.
hiPathWirelessHWCAlarms	1.3.6.1.4.1.4329.15.3.30.3			Conformance information for the alarm groups.
hiPathWirelessHWCObsolete	1.3.6.1.4.1.4329.15.3.30.4			List of object that EWC does not anymore support.
wirelessEWCGroups	1.3.6.1.4.1.4329.15.3.30.5
physicalPortsGroup	1.3.6.1.4.1.4329.15.3.30.5.1			Physical ports and their attributes.
phyDHCPRangeGroup	1.3.6.1.4.1.4329.15.3.30.5.2			DHCP objects and attributes associated to physical ports.
layerTwoPortGroup	1.3.6.1.4.1.4329.15.3.30.5.3			Collection of layer two ports objects.
muGroup	1.3.6.1.4.1.4329.15.3.30.5.4			MU attributes associated to EWC.
apStatsGroup	1.3.6.1.4.1.4329.15.3.30.5.5			Collection of objects and attributes related to AP statistics.
muACLGroup	1.3.6.1.4.1.4329.15.3.30.5.6			List of objects for creation of blacklist/whitelist.
siteGroup	1.3.6.1.4.1.4329.15.3.30.5.7			A collection of objects providing Site creation and its attributes.
sitePolicyGroup	1.3.6.1.4.1.4329.15.3.30.5.8			Objects defining the association of policies to sites.
siteCosGroup	1.3.6.1.4.1.4329.15.3.30.5.9			Objects defining the association of policies to sites.
siteAPGroup	1.3.6.1.4.1.4329.15.3.30.5.10			Objects defining the association of policies to sites.
siteWlanGroup	1.3.6.1.4.1.4329.15.3.30.5.11			Objects defining the association of policies to sites.
apGroup	1.3.6.1.4.1.4329.15.3.30.5.12			List of objects defining configuration attributes of an AP.
wlanGroup	1.3.6.1.4.1.4329.15.3.30.5.13			List of objects defining configuration attributes of a WLAN.
wlanStatsGroup	1.3.6.1.4.1.4329.15.3.30.5.14			List of objects defining configuration attributes of a WLAN.
topologyGroup	1.3.6.1.4.1.4329.15.3.30.5.15			List of objects defining configuration attributes of a WLAN.
topologyStatGroup	1.3.6.1.4.1.4329.15.3.30.5.16			List of objects for defining topology statics.
loadGroup	1.3.6.1.4.1.4329.15.3.30.5.17			A collection of objects providing Load Group creation and its attributes.
widsWipsObjectsGroup	1.3.6.1.4.1.4329.15.3.30.5.18			Objects defining the state of WIDS-WIPS for the controller.
widsWipsEngineGroup	1.3.6.1.4.1.4329.15.3.30.5.19			Set of objects defining attributes of a WIDS-WIPS engine.
outOfServiceScanGroup	1.3.6.1.4.1.4329.15.3.30.5.20			List of objects for defining out-of-service scan group.
inServiceScanGroup	1.3.6.1.4.1.4329.15.3.30.5.21			List of objects for defining in-service scan group.
scanGroupAPAssignmentGroup	1.3.6.1.4.1.4329.15.3.30.5.22			List of objects for assignment of AP to scan group.
scanAPGroup	1.3.6.1.4.1.4329.15.3.30.5.23			List of objects for defining AP scan groups in EWC.
friendlyAPGroup	1.3.6.1.4.1.4329.15.3.30.5.24			List of objects defining friendly APs identified during scanning time.
wlanSecurityReportGroup	1.3.6.1.4.1.4329.15.3.30.5.25			Set of objects defining attributes of security group report.
apAntennaGroup	1.3.6.1.4.1.4329.15.3.30.5.26			A collection of objects defining an antenna attributes for an AP.
muAccessListGroup	1.3.6.1.4.1.4329.15.3.30.5.27			List of objects for creation of MU access list to block MU access, case of black list, or allow access, case of white list to wireless controller resources.
activeThreatGroup	1.3.6.1.4.1.4329.15.3.30.5.28			List of objects defining a discovered security threat.
countermeasureAPGroup	1.3.6.1.4.1.4329.15.3.30.5.29			List of objects defining APs taking part in countermeasure activities to thwart incoming threats.
blaclistedClientGroup	1.3.6.1.4.1.4329.15.3.30.5.30			List of objects identifying blacklisted clients.
threatSummaryGroup	1.3.6.1.4.1.4329.15.3.30.5.31			List of objects defining attributes of known discovered threat.
licensingInformationGroup	1.3.6.1.4.1.4329.15.3.30.5.32			List of objects providing licensing information for the controller system.
stationsByProtocolGroup	1.3.6.1.4.1.4329.15.3.30.5.33			List of objects for aggregated MUs on a specific wireless channel.
apByChannelGroup	1.3.6.1.4.1.4329.15.3.30.5.34			List of objects for aggregated access points on a wireless channel.
uncategorizedAPGroup	1.3.6.1.4.1.4329.15.3.30.5.35			Objects defining uncategorized access points discovered by Radar application.
authorizedAPGroup	1.3.6.1.4.1.4329.15.3.30.5.36			Objects defining authorized access points discovered by Radar application.
prohibitedAPGroup	1.3.6.1.4.1.4329.15.3.30.5.37			Objects defining prohibited access points discovered by Radar application.
dedicatedScanGroup	1.3.6.1.4.1.4329.15.3.30.5.38			List of objects for defining dedicated scan group.
apRadioAntennaGroup	1.3.6.1.4.1.4329.15.3.30.5.39			A collection of objects defining an antenna attributes for an AP.
radiusFastFailoverEventsGroup	1.3.6.1.4.1.4329.15.3.30.5.40			List of objects for defining radius FastFailoverEvents.
dhcpRelayListenersGroup	1.3.6.1.4.1.4329.15.3.30.5.41			List of objects for defining dhcpRelayListeners.
authenticationAdvancedGroup	1.3.6.1.4.1.4329.15.3.30.5.42			List of objects for defining authenticationAdvanced.
radiusExtnsSettingGroup	1.3.6.1.4.1.4329.15.3.30.5.43			List of objects for defining radiusExtnsSetting.
hiPathWirelessControllerMib	1.3.6.1.4.1.4329.15.5.2			The access controller MIB

RFC description

HiPath wireless controller MIB for managing WLAN access points, stations, and wireless network operations.

Start monitoring Siemens/Enterasys HiPath Wireless Controller (HWC) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HIPATH-WIRELESS-HWC-MIB