HH3C-SNA-DLSW-EXT-MIB

All MIBs › HH3C-SNA-DLSW-EXT-MIB

Organization: Hangzhou H3C Tech. Co., Ltd.

Last Updated: 2005-07-20

Category: Domain: SNA/Legacy, SNA and Legacy Protocols, Vendor: H3C/HH3C

Description: HH3C extension MIB for SNA Data Link Switching (DLSw) providing vendor-specific DLSw management objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HH3C-SNA-DLSW-EXT-MIB?

HH3C-SNA-DLSW-EXT-MIB is an H3C (Hangzhou Huawei-3Com/New H3C) enterprise MIB extending standard Data Link Switching (DLSw) management with vendor-specific configuration objects for SNA-over-IP transport. It exposes per-node configuration data such as vendor ID, local IP address, priority, pacing window sizes, keepalive interval, and various connection/pending timeouts governing DLSw peer behavior. Its monitoring value lies mainly in software/protocol configuration and connection-state tuning rather than hardware sensors, letting an administrator verify DLSw peer timers and pacing settings that affect SNA session reliability over the WAN. It explicitly depends on and extends the standard DLSw protocol defined in RFC 1795, RFC 2024, and RFC 2166, layering H3C-specific enhancements on top of that IETF baseline. It is typically deployed on H3C routers providing legacy SNA/mainframe traffic encapsulation (DLSw) across a modern IP WAN, and network engineers can download the HH3C-SNA-DLSW-EXT-MIB file to load it into their MIB browser for reference.

IPNetwork Monitor allows you to monitor SNMP objects defined in HH3C-SNA-DLSW-EXT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C router providing SNA/DLSw over IP

Monitoring Examples

An administrator would check hh3cdeNodeKeepAliveInterval and hh3cdeNodeConnTimeout to diagnose why a DLSw peer connection is dropping or failing to establish reliably. hh3cdeNodeInitPacingWindow and hh3cdeNodeMaxPacingWindow would be reviewed when SNA sessions experience throughput problems, since pacing window mismatches between DLSw peers can throttle data flow. hh3cdeNodeLocalAddr and hh3cdeNodePriority help confirm which local node identity and priority are advertised in DLSw peer negotiation.

What Can Be Monitored

DLSw peer keepalive interval
connection timeout settings
pacing window sizes
node priority
local IP address configuration

Imported Objects

From DLSW-MIB

LFSize
MacAddressNC
TAddress
dlswTConnConfigEntry	OBJECT-TYPE
dlswTConnOperEntry	OBJECT-TYPE
dlswTConnTcpConfigEntry	OBJECT-TYPE

From HH3C-OID-MIB

hh3cCommon

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From RFC1213-MIB

ifIndex

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

RowStatus

How to Use in IPNetwork Monitor

Example using hh3cdeTConnOperRecvPkts OID:

Select an H3C router providing SNA/DLSw over IP (extended config) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hh3cdeTConnOperRecvPkts into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of Switch-to-Switch Protocol (SSP) messages received on this tcp transport connection. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hh3cDlswExt	1.3.6.1.4.1.25506.2.62			The MIB module for management of H3C specific Data Link Switching protocol enhancements. DLSw is described in RFC 1795, RFC 2024 and RFC2166.
hh3cDlswExtMIBObjects	1.3.6.1.4.1.25506.2.62.1
hh3cdeNode	1.3.6.1.4.1.25506.2.62.1.1
OCT hh3cdeNodeVendorID	1.3.6.1.4.1.25506.2.62.1.1.1	OCTET STRING	read-write	The value identifies the manufacturer's IEEE-assigned Organizationally Unique Identifier (OUI) of this DLSw. This information is reported in DLSw Capabilities Exchange.
IPt hh3cdeNodeIpAddrType	1.3.6.1.4.1.25506.2.62.1.1.2	InetAddressType	read-write	The type of ip address: IPv4 or IPv6.
IP hh3cdeNodeLocalAddr	1.3.6.1.4.1.25506.2.62.1.1.3	InetAddress	read-write	Local peer ip address. This ip address must have been configured for a port on the router. If no local peer ip address is configured, then this object will be the empty string.
I32 hh3cdeNodePriority	1.3.6.1.4.1.25506.2.62.1.1.4	Integer32	read-write	Peer priority advertised to remote peers in the DLSw Capabilities Exchange. If an end station can reach through more than one peer, the priority of each peer will be considered when a circuit is established. A lower priority indicates that peer will be the preferred choice if there are more than one path to the destination. A value of 65535 indicates the value is meaningless.
I32 hh3cdeNodeInitPacingWindow	1.3.6.1.4.1.25506.2.62.1.1.5	Integer32	read-write	Initial pacing window size. This is the starting size of the pacing window. DLSw uses an adaptive pacing flow control algorithm that automatically adjusts to congestion levels in the network. Pacing windows are used to control how many packets may be sent to a peer before acknowlegement. A value of 65535 indicates the value is meaningless.
I32 hh3cdeNodeMaxPacingWindow	1.3.6.1.4.1.25506.2.62.1.1.6	Integer32	read-write	Maximum pacing window size. This is the largest size that the pacing window will grow to. DLSw uses an adaptive pacing flow control algorithm that automatically adjusts to congestion levels in the network. Pacing windows are used to control how many packets may be sent to a peer before acknowlegement.
I32 hh3cdeNodeKeepAliveInterval	1.3.6.1.4.1.25506.2.62.1.1.7	Integer32	read-write	Default remote peer keepalive interval in seconds. The keepalive parameter refers to how often DLSw peers send peer keep alives to each other. These periodic messages allow DLSw to keep track of the state of all peers. If set to zero, no keepalives are sent. A value of 65535 indicates the value is meaningless.
INT hh3cdeNodePermitDynamic	1.3.6.1.4.1.25506.2.62.1.1.8	INTEGER	read-write	To accept connections from non-configured remote peer when permitDynamic is specified.
I32 hh3cdeNodeConnTimeout	1.3.6.1.4.1.25506.2.62.1.1.9	Integer32	read-write	Define connected state timer.
I32 hh3cdeNodeLocalPendTimeout	1.3.6.1.4.1.25506.2.62.1.1.10	Integer32	read-write	Define connected state timer.
I32 hh3cdeNodeRemotePendTimeout	1.3.6.1.4.1.25506.2.62.1.1.11	Integer32	read-write	Define connected state timer.
I32 hh3cdeNodeSnaCacheTimeout	1.3.6.1.4.1.25506.2.62.1.1.12	Integer32	read-write	Define connected state timer.
I32 hh3cdeNodeExplorerTimeout	1.3.6.1.4.1.25506.2.62.1.1.13	Integer32	read-write	Define explorer timer.
I32 hh3cdeNodeExplorerWaitTimeout	1.3.6.1.4.1.25506.2.62.1.1.14	Integer32	read-write	Define explorer waiting timer.
OCT hh3cdeNodeConfigSapList	1.3.6.1.4.1.25506.2.62.1.1.15	OCTET STRING	read-write	The SAP list indicates which SAPs are allowed. Only SAPs with even numbers are represented, in the form of the most significant bit of the first octet representing the SAP 0, the next most significant bit representing the SAP 2, to the least significant bit of the last octet representing the SAP 254. Data link switching is allowed for those SAPs which have one in its corresponding bit, not allowed otherwise. The whole SAP list has to be changed together. Changing the SAP list affects only new circuit establishments and has no effect on established circuits. This list can be used to restrict specific partners from knowing about all the SAPs used by DLSw on all its interfaces (these are represented in hh3cdeIfSapList for each interface). For instance, one may want to run NetBIOS with some partners but not others. If a node supports sending run-time capabilities exchange messages, changes to this object should cause that action. When to start the run-time capabilities exchange is implementation-specific. The DEFVAL below indicates support for SAPs 0, 2, 4, 6, 8, A, C and E.
I32 hh3cdeNodeMaxTransmission	1.3.6.1.4.1.25506.2.62.1.1.16	Integer32	read-write	The maximum retry times for TCP packet. Default value is 5.
INT hh3cdeNodeMulticastStatus	1.3.6.1.4.1.25506.2.62.1.1.17	INTEGER	read-write	Multicast support status. It is disabled by default.
IP hh3cdeNodeMulticastAddress	1.3.6.1.4.1.25506.2.62.1.1.18	InetAddress	read-write	Multicast address. Default is 224.0.10.0. When the hh3cdeNodeMulticastStatus is disabled, the multicast address is reset to 0.0.0.0.
INT hh3cdeNodeResetTcpAll	1.3.6.1.4.1.25506.2.62.1.1.19	INTEGER	read-write	Reset all TCP circuit switch. Any return value is meaningless.
I32 hh3cdeNodeStCapTcpNum	1.3.6.1.4.1.25506.2.62.1.1.20	Integer32	read-write	Tcp number reported in DLSw Capabilities Exchange.
I32 hh3cdeNodeTcpQueueMax	1.3.6.1.4.1.25506.2.62.1.1.21	Integer32	read-write	The max length of TCP queue.
hh3cdeTConn	1.3.6.1.4.1.25506.2.62.1.2
hh3cdeTConnConfigTable	1.3.6.1.4.1.25506.2.62.1.2.1		not-accessible	This table defines the peer transport connections that will be initiated or accepted by this DLSw. This table augments dlswTConnConfigTable.
hh3cdeTConnConfigEntry	1.3.6.1.4.1.25506.2.62.1.2.1.1		not-accessible	A list of objects that define specific configuration for a DLSw peer transport connection.
OCT hh3cdeTConnConfigVersion	1.3.6.1.4.1.25506.2.62.1.2.1.1.1	OCTET STRING	read-create	This value identifies which version (first octet) and release (second octet) of the DLSw standard is supported by this partner DLSw. This information is obtained from a DLSw Capabilities Exchange message received from the partner DLSw. A string of zero length is returned before a Capabilities Exchange message is received, or if one is never received. A conceptual row with a hh3cdeTConnOperState of 'connected' but a zero length partner version indicates that the partner is a non-standard DLSw partner. If an implementation chooses to keep hh3cdeTConnOperEntrys in the 'disconnected' state, this value should remain unchanged.
I32 hh3cdeTConnConfigPriority	1.3.6.1.4.1.25506.2.62.1.2.1.1.2	Integer32	read-create	The priority for remote peer.
LFS hh3cdeTConnConfigLfSize	1.3.6.1.4.1.25506.2.62.1.2.1.1.3	LFSize	read-create	The largest frame size.
I32 hh3cdeTConnConfigKeepaliveIntval	1.3.6.1.4.1.25506.2.62.1.2.1.1.4	Integer32	read-create	The keepalive interval value.
INT hh3cdeTConnConfigBackup	1.3.6.1.4.1.25506.2.62.1.2.1.1.5	INTEGER	read-create	The current remote peer is configured as the backup of another configured remote peer.
ADR hh3cdeTConnConfigBackupTAddr	1.3.6.1.4.1.25506.2.62.1.2.1.1.6	TAddress	read-create	It is the ip address of a configured remote peer of which the current remote peer is configrued as backup.
I32 hh3cdeTConnConfigBackupLinger	1.3.6.1.4.1.25506.2.62.1.2.1.1.7	Integer32	read-create	Backup peer linger.
hh3cdeTConnOperTable	1.3.6.1.4.1.25506.2.62.1.2.2		not-accessible	A list of peer transport connections. Each connected peer will create a conceptual row in the table. When the peer disconnects, the row will be deleted from the table. This table augments dlswTConnOperTable.
hh3cdeTConnOperEntry	1.3.6.1.4.1.25506.2.62.1.2.2.1		not-accessible	A list of objects that contain spefific operational information for a DLSw peer transport connection.
INT hh3cdeTConnOperPeerType	1.3.6.1.4.1.25506.2.62.1.2.2.1.1	INTEGER	read-only	The current remote peer is configured when the value is 'configured'.
OCT hh3cdeTConnOperVendorID	1.3.6.1.4.1.25506.2.62.1.2.2.1.2	OCTET STRING	read-only	The value identifies the manufacturer's IEEE-assigned Organizationally Unique Identifier (OUI) of remote peer.
OCT hh3cdeTConnOperVersionString	1.3.6.1.4.1.25506.2.62.1.2.2.1.3	OCTET STRING	read-only	Version information of remote peer. The length up to 512 bytes.
TIK hh3cdeTConnOperUpTime	1.3.6.1.4.1.25506.2.62.1.2.2.1.4	TimeTicks	read-only	The amount of time (in seconds) since this transport connection last entered the 'connected' state.
ADR hh3cdeTConnOperMulticastAddress	1.3.6.1.4.1.25506.2.62.1.2.2.1.5	TAddress	read-only	When remote peer supports DLSw2.0, this node identifies its multicast address.
I32 hh3cdeTConnOperStCapTcpNumber	1.3.6.1.4.1.25506.2.62.1.2.2.1.6	Integer32	read-only	Number of tcp supported when capabilities exchanging.
C32 hh3cdeTConnOperRecvPktsEx	1.3.6.1.4.1.25506.2.62.1.2.2.1.7	Counter32	read-only	The number of Switch-to-Switch Protocol (SSP) messages received on this tcp transport connection.
C32 hh3cdeTConnOperSendPkts	1.3.6.1.4.1.25506.2.62.1.2.2.1.8	Counter32	read-only	The number of SSP messages sent on this tcp transport connection.
C32 hh3cdeTConnOperDropPkts	1.3.6.1.4.1.25506.2.62.1.2.2.1.9	Counter32	read-only	The number of SSP messages dropped on this tcp transport connection.
hh3cdeTConnTcpConfigTable	1.3.6.1.4.1.25506.2.62.1.2.3		not-accessible	This table defines the TCP transport connections that will be either initiated by or accepted by this DSLw. It augments the entries in dlswTConnConfigTable whose domain is dlswTCPDomain. In other words for each conceptual row in the dlswTConnConfigTable, if the dlswTConnConfigTDomain is dlswTCPDomain, that conceptual row will be augmented by this table. dlswTCPDomain, dlswTConnConfigTable, and dlswTConnConfigTDomain are all imported from DLSW-MIB (RFC 2024). This table augments dlswTConnTcpConfigTable.
hh3cdeTConnTcpConfigEntry	1.3.6.1.4.1.25506.2.62.1.2.3.1		not-accessible	A list of objects that define specific configuration for a DLSw peer transport connection within the dlswTCPDomain. dlswTCPDomain is imported from DLSW-MIB (RFC 2024).
I32 hh3cdeTConnTcpConfigQueueMax	1.3.6.1.4.1.25506.2.62.1.2.3.1.1	Integer32	read-create	Maximum output TCP queue size for this remote peer. For DLSw over TCP encapsulation, packets may be queued due to congestion of the TCP network. This variable is used to set the output queue maximum of the underlying TCP connection for the peer represented by the conceptual row.
hh3cdeBridge	1.3.6.1.4.1.25506.2.62.1.3
hh3cdeBridgeTable	1.3.6.1.4.1.25506.2.62.1.3.1		not-accessible	A list of bridge group which is serving for DLSw.
hh3cdeBridgeEntry	1.3.6.1.4.1.25506.2.62.1.3.1.1		not-accessible	A list of bridge information.
I32 hh3cdeBridgeNumIndex	1.3.6.1.4.1.25506.2.62.1.3.1.1.1	Integer32	not-accessible	This value identifies the bridge number.
ROW hh3cdeBridgeRowStatus	1.3.6.1.4.1.25506.2.62.1.3.1.1.2	RowStatus	read-create	RowStatus.
hh3cdeBridgeIfTable	1.3.6.1.4.1.25506.2.62.1.3.2		not-accessible	The list of interface on which DLSw is active.
hh3cdeBridgeIfEntry	1.3.6.1.4.1.25506.2.62.1.3.2.1		not-accessible	The list of bridge interface information.
I32 hh3cdeBridgeIfBrgGrp	1.3.6.1.4.1.25506.2.62.1.3.2.1.1	Integer32	read-create	This value identifies the bridge number attached to the interface.
ROW hh3cdeBridgeIfRowStatus	1.3.6.1.4.1.25506.2.62.1.3.2.1.2	RowStatus	read-create	RowStatus.
hh3cdeQllc	1.3.6.1.4.1.25506.2.62.1.4
hh3cdeQllcTable	1.3.6.1.4.1.25506.2.62.1.4.1		not-accessible	The table defines attributes related for those QLLC that participate in data link switching.
hh3cdeQllcEntry	1.3.6.1.4.1.25506.2.62.1.4.1.1		not-accessible	The ifIndex belongs to the interface which link protocol is x.25.
I32 hh3cQllcX121Address	1.3.6.1.4.1.25506.2.62.1.4.1.1.1	Integer32	read-create	X.121 address.
ADR hh3cQllcLocalMac	1.3.6.1.4.1.25506.2.62.1.4.1.1.2	MacAddressNC	read-create	The virtual MAC address used to represent the QLLC-attached link station to the rest of the DLSw network.
OCT hh3cQllcLocalSap	1.3.6.1.4.1.25506.2.62.1.4.1.1.3	OCTET STRING	read-create	The SAP used to represent this link station.
ADR hh3cQllcRemoteMac	1.3.6.1.4.1.25506.2.62.1.4.1.1.4	MacAddressNC	read-create	The MAC address to which DLSw should attempt to connect this link station. If this information is not available, a length of zero for this object should be returned.
OCT hh3cQllcRemoteSap	1.3.6.1.4.1.25506.2.62.1.4.1.1.5	OCTET STRING	read-create	The SAP of the remote station to which this link station should be connected. If this information is not available, a length of zero for this object should be returned.
ROW hh3cQllcRowStatus	1.3.6.1.4.1.25506.2.62.1.4.1.1.6	RowStatus	read-create	RowStatus.
hh3cdeSdlc	1.3.6.1.4.1.25506.2.62.1.5
hh3cdeSdlcPortTable	1.3.6.1.4.1.25506.2.62.1.5.1		not-accessible	The table defines parameters for the interfaces whose link protocol is SDLC.
hh3cdeSdlcPortEntry	1.3.6.1.4.1.25506.2.62.1.5.1.1		not-accessible	Sdlc port entry.
INT hh3cdeSdlcPortRole	1.3.6.1.4.1.25506.2.62.1.5.1.1.1	INTEGER	read-create	The SDLC role of interface.
I32 hh3cdeSdlcPortSendWindow	1.3.6.1.4.1.25506.2.62.1.5.1.1.2	Integer32	read-create	Size of local send window.
INT hh3cdeSdlcPortModulo	1.3.6.1.4.1.25506.2.62.1.5.1.1.3	INTEGER	read-create	Size of modulus.
I32 hh3cdeSdlcPortMaxPdu	1.3.6.1.4.1.25506.2.62.1.5.1.1.4	Integer32	read-create	Maximum bytes for incoming frames.
I32 hh3cdeSdlcPortMaxSendQueue	1.3.6.1.4.1.25506.2.62.1.5.1.1.5	Integer32	read-create	Size of hold queue.
I32 hh3cdeSdlcPortMaxTransmission	1.3.6.1.4.1.25506.2.62.1.5.1.1.6	Integer32	read-create	Number of times to retry an operation.
INT hh3cdeSdlcPortSimultaneousEnable	1.3.6.1.4.1.25506.2.62.1.5.1.1.7	INTEGER	read-create	Activate SDLC two-way simultaneous mode.
I32 hh3cdeSdlcPortTimerACK	1.3.6.1.4.1.25506.2.62.1.5.1.1.8	Integer32	read-create	Time to wait for a reply to a frame.
I32 hh3cdeSdlcPortTimerLifeTime	1.3.6.1.4.1.25506.2.62.1.5.1.1.9	Integer32	read-create	Time to wait for a reply used by secondary station.
I32 hh3cdeSdlcPortTimerPollPause	1.3.6.1.4.1.25506.2.62.1.5.1.1.10	Integer32	read-create	Time between polls for each secondary SDLC station.
ROW hh3cdeSdlcPortRowStatus	1.3.6.1.4.1.25506.2.62.1.5.1.1.11	RowStatus	read-create	RowStatus.
hh3cdeLlc2	1.3.6.1.4.1.25506.2.62.1.6
hh3cdeLlc2PortTable	1.3.6.1.4.1.25506.2.62.1.6.1		not-accessible	This table defines parameters for the Ethernet interface.
hh3cdeLlc2PortEntry	1.3.6.1.4.1.25506.2.62.1.6.1.1		not-accessible	LLC2 port entry.
I32 hh3cdeLlc2PortMaxAck	1.3.6.1.4.1.25506.2.62.1.6.1.1.1	Integer32	read-create	Maximum of I-frames received before ACK.
I32 hh3cdeLlc2PortMaxPdu	1.3.6.1.4.1.25506.2.62.1.6.1.1.2	Integer32	read-create	Maximum of LLC2 pdu length.
I32 hh3cdeLlc2PortMaxSendQueue	1.3.6.1.4.1.25506.2.62.1.6.1.1.3	Integer32	read-create	Queue for sending llc2 I-frames.
I32 hh3cdeLlc2PortMaxTransmission	1.3.6.1.4.1.25506.2.62.1.6.1.1.4	Integer32	read-create	Retry times of operations.
INT hh3cdeLlc2PortModulo	1.3.6.1.4.1.25506.2.62.1.6.1.1.5	INTEGER	read-create	Modulus of LLC2.
I32 hh3cdeLlc2PortReceiveWindow	1.3.6.1.4.1.25506.2.62.1.6.1.1.6	Integer32	read-create	Maximum number of I-frames to send before received ACK.
I32 hh3cdeLlc2PortTimerAck	1.3.6.1.4.1.25506.2.62.1.6.1.1.7	Integer32	read-create	Waiting for ACK time after sending an I-frame.
I32 hh3cdeLlc2PortTimerAckDelay	1.3.6.1.4.1.25506.2.62.1.6.1.1.8	Integer32	read-create	Maximum time allows I-frames incoming without replay ACK.
I32 hh3cdeLlc2PortTimerDetect	1.3.6.1.4.1.25506.2.62.1.6.1.1.9	Integer32	read-create	Detect the link status.
I32 hh3cdeLlc2PortTimerBusy	1.3.6.1.4.1.25506.2.62.1.6.1.1.10	Integer32	read-create	Waiting time while other LLC2 station is in busy state.
I32 hh3cdeLlc2PortTimerPoll	1.3.6.1.4.1.25506.2.62.1.6.1.1.11	Integer32	read-create	Waiting time after a P frame is sent.
I32 hh3cdeLlc2PortTimerReject	1.3.6.1.4.1.25506.2.62.1.6.1.1.12	Integer32	read-create	Waiting time after a REJ frame is sent.
ROW hh3cdeLlc2PortRowStatus	1.3.6.1.4.1.25506.2.62.1.6.1.1.13	RowStatus	read-create	RowStatus.
hh3cdeReachableCache	1.3.6.1.4.1.25506.2.62.1.7
hh3cdeRchCacheStat	1.3.6.1.4.1.25506.2.62.1.7.1
I32 hh3cdeRchCacheMaxIndex	1.3.6.1.4.1.25506.2.62.1.7.1.1	Integer32	read-only	Maximum of hh3cdeRchCacheIndex.
I32 hh3cdeRchCacheNextIndex	1.3.6.1.4.1.25506.2.62.1.7.1.2	Integer32	read-only	The next value of hh3cdeRchCacheIndex to be assigned by the agent. A retrieval of this object atomically reserves the returned value for use by the manager to create a row in hh3cdeRchCacheTable. This makes it possible for the agent to control the index space of the MAC address cache, yet allows the manager to administratively create new rows.
hh3cdeRchCacheTable	1.3.6.1.4.1.25506.2.62.1.7.3		not-accessible	Reachable cache table.
hh3cdeRchCacheEntry	1.3.6.1.4.1.25506.2.62.1.7.3.1		not-accessible	Reachable cache entry.
I32 hh3cdeRchCacheIndex	1.3.6.1.4.1.25506.2.62.1.7.3.1.1	Integer32	not-accessible	Index of reachable cache entry.
INT hh3cdeRchCacheStatus	1.3.6.1.4.1.25506.2.62.1.7.3.1.2	INTEGER	read-only	Current status of reachable cache entry.
TIK hh3cdeRchCacheRemainTime	1.3.6.1.4.1.25506.2.62.1.7.3.1.3	TimeTicks	read-only	Remain time of reachable cache entry.
ADR hh3cdeRchCacheMac	1.3.6.1.4.1.25506.2.62.1.7.3.1.4	MacAddressNC	read-create	MAC address of reachable cache entry.
IPt hh3cdeRchCacheRemoteIpAddrType	1.3.6.1.4.1.25506.2.62.1.7.3.1.5	InetAddressType	read-create	Remote peer ip address type.
IP hh3cdeRchCacheRemoteIp	1.3.6.1.4.1.25506.2.62.1.7.3.1.6	InetAddress	read-create	Remote peer ip address of reachable cache entry.
ROW hh3cdeRchCacheRowStatus	1.3.6.1.4.1.25506.2.62.1.7.3.1.7	RowStatus	read-create	RowStatus.
hh3cdeEthernetBackup	1.3.6.1.4.1.25506.2.62.1.8
hh3cdeEBMacMapStat	1.3.6.1.4.1.25506.2.62.1.8.1
I32 hh3cdeEBMacMapMaxIndex	1.3.6.1.4.1.25506.2.62.1.8.1.1	Integer32	read-only	Maximum of hh3cdeEBMacMapIndex.
I32 hh3cdeEBMacMapNextIndex	1.3.6.1.4.1.25506.2.62.1.8.1.2	Integer32	read-only	The next value of hh3cdeEBMacMapIndex to be assigned by the agent. A retrieval of this object atomically reserves the returned value for use by the manager to create a row in hh3cdeEBMacMapTable. This makes it possible for the agent to control the index space of the MAC mapping tables, yet allows the manager to administratively create new rows.
hh3cdeEBIfTable	1.3.6.1.4.1.25506.2.62.1.8.3		not-accessible	Information of interface which works for DLSw Ethernet redundancy.
hh3cdeEBIfEntry	1.3.6.1.4.1.25506.2.62.1.8.3.1		not-accessible	Parameters defined for DLSw Ethernet redundancy interface.
ADR hh3cdeEBMulticastMac	1.3.6.1.4.1.25506.2.62.1.8.3.1.1	MacAddressNC	read-create	Multicast MAC address configured for the Ethernet redundancy of dlsw module. When Ethernet redundancy is inactive, its value is '000000000000'H. To active Ethernet redundancy, give it a valid multicast MAC address.
I32 hh3cdeEBPriority	1.3.6.1.4.1.25506.2.62.1.8.3.1.2	Integer32	read-create	Priority configured for the Ethernet redundancy of DLSw module.
I32 hh3cdeEBtimer	1.3.6.1.4.1.25506.2.62.1.8.3.1.3	Integer32	read-create	Timer for the Ethernet redundancy of DLSw module.
ROW hh3cdeEBRowStatus	1.3.6.1.4.1.25506.2.62.1.8.3.1.4	RowStatus	read-create	RowStatus.
hh3cdeEBMacMapTable	1.3.6.1.4.1.25506.2.62.1.8.4		not-accessible	MAC address mapping table.
hh3cdeEBMacMapEntry	1.3.6.1.4.1.25506.2.62.1.8.4.1		not-accessible	MAC address mapping entry.
I32 hh3cdeEBMacMapIndex	1.3.6.1.4.1.25506.2.62.1.8.4.1.1	Integer32	not-accessible	Index of MAC address mapping entry.
ADR hh3cdeEBMacMapLocalMac	1.3.6.1.4.1.25506.2.62.1.8.4.1.2	MacAddressNC	read-create	Local MAC address in MAC address mapping. When creating a new conceptual row, hh3cdeEBMacMapLocalMac and hh3cdeEBMacMapRemoteMac should be set simultaneously.
ADR hh3cdeEBMacMapRemoteMac	1.3.6.1.4.1.25506.2.62.1.8.4.1.3	MacAddressNC	read-create	Remote MAC address of MAC address mapping. When creating a new conceptual row, hh3cdeEBMacMapLocalMac and hh3cdeEBMacMapRemoteMac should be set simultaneously.
ADR hh3cdeEBMacMapNeighbour	1.3.6.1.4.1.25506.2.62.1.8.4.1.4	MacAddressNC	read-create	Neighbour of MAC address mapping.
ROW hh3cdeEBMacMapRowStatus	1.3.6.1.4.1.25506.2.62.1.8.4.1.5	RowStatus	read-create	Status of MAC address mapping entry.

RFC description

Vendor-private MIB for H3C SNA Data Link Switch (DLSw) extensions; manages advanced DLSw protocol features for legacy network support.

Start monitoring H3C router providing SNA/DLSw over IP (extended config) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HH3C-SNA-DLSW-EXT-MIB