HH3C-EPON-DEVICE-MIB

All MIBs › HH3C-EPON-DEVICE-MIB

Organization: Hangzhou H3C Tech. Co., Ltd.

Last Updated: 2004-09-21

Category: Technology: EPON/PON, Vendor: H3C/HH3C

Description: Manages EPON OLT device-level parameters including port capacity and system configuration on H3C access platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HH3C-EPON-DEVICE-MIB?

HH3C-EPON-DEVICE-MIB is an H3C enterprise MIB for device-level management of EPON (Ethernet Passive Optical Network) OLT equipment, based on the IEEE 802.3ah EFM PON draft standard, covering system-level configuration such as port capacity and overall device parameters rather than per-ONU detail. It is expected to expose OLT chassis/board-level configuration and status objects tied to the PON hardware. Its intended monitoring role is hardware status of the OLT device itself, confirming port capacity, board presence, and overall device configuration health as the aggregation point for many ONUs. It explicitly derives from the IEEE 802.3ah EFM PON draft standard as its normative reference, adapted with an hh3c object-name prefix. Typical deployment is on H3C EPON OLT chassis in fiber access networks. Engineers can download the HH3C-EPON-DEVICE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HH3C-EPON-DEVICE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

H3C EPON OLT (optical line terminal) chassis

Monitoring Examples

No specific objects were sampled for this MIB, so exact identifiers can't be cited, but based on its stated scope an operator would typically check OLT-level port-capacity and device configuration objects to confirm the chassis is provisioned correctly and to detect a board or port-capacity mismatch affecting downstream ONU service.

What Can Be Monitored

OLT port capacity
device/system configuration status

Imported Objects

From HH3C-OID-MIB

hh3cEpon

OBJECT-IDENTITY

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32
mib-2
zeroDotZero

From SNMPv2-TC

DateAndTime
MacAddress
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using hh3cEponDeviceStatTxFramesQueue0 OID:

Select an H3C EPON OLT chassis (802.3ah device management) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hh3cEponDeviceStatTxFramesQueue0 into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports a count of the number of times a -Queue-0- frames transmission occurs. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline (in frames), since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hh3cEponDeviceCompliance	1.3.6.1.4.1.25506.2.42.4.1.2.2.1			The compliance statement for EPON Devices.
hh3cEponDeviceCompliances	1.3.6.1.4.1.25506.2.42.4.1.2.2
hh3cEponDeviceConformance	1.3.6.1.4.1.25506.2.42.4.1.2
hh3cEponDeviceControlEntry	1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1		not-accessible	An entry in the EPON device Control table.
hh3cEponDeviceControlObjects	1.3.6.1.4.1.25506.2.42.4.1.1.1
hh3cEponDeviceControlTable	1.3.6.1.4.1.25506.2.42.4.1.1.1.1		not-accessible	Table for EPON device MIB modules.
T/F hh3cEponDeviceCriticalEventEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.5	TruthValue	read-write	A control to allow CriticalEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
T/F hh3cEponDeviceCriticalEventState	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.4	TruthValue	read-only	A read-only variable, which defines the state of the Critical Event indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a Critical Event asserted. When false the Critical Event is reset.
T/F hh3cEponDeviceDyingGaspAlarmEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.3	TruthValue	read-write	A control to allow DyingGaspAlarm event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
T/F hh3cEponDeviceDyingGaspAlarmState	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.2	TruthValue	read-only	A read-only variable, which defines the state of the Dying Gasp indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a dying gasp alarm asserted. When false the dying gasp alarm is reset
T/F hh3cEponDeviceErroredFrameEventEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.17	TruthValue	read-write	A control to allow ErroredFrameEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
T/F hh3cEponDeviceErroredFrameEventState	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.16	TruthValue	read-only	A read-only variable, which defines the state of the Errored Frame Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Event asserted. When false the Errored Frame Event is reset.
T/F hh3cEponDeviceErroredFramePeriodEventEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.19	TruthValue	read-write	A control to allow ErroredFramePeriodEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
T/F hh3cEponDeviceErroredFramePeriodEventState	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.18	TruthValue	read-only	A read-only variable, which defines the state of the Errored Frame Period Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Period Event asserted. When false the Errored Frame Period Event is reset.
T/F hh3cEponDeviceErroredFrameSecondsSummaryEventEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.21	TruthValue	read-write	A control to allow ErroredFrameSecondsSummaryEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
T/F hh3cEponDeviceErroredFrameSecondsSummaryEventState	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.20	TruthValue	read-only	A read-only variable, which defines the state of the Errored Frame Seconds Summary Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Frame Seconds Summary Event asserted. When false the Errored Frame Seconds Summary Event is reset.
T/F hh3cEponDeviceErroredSymbolPeriodEventEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.15	TruthValue	read-write	A control to allow ErroredSymbolPeriodEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
T/F hh3cEponDeviceErroredSymbolPeriodEventState	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.14	TruthValue	read-only	A read-only variable, which defines the state of the Errored Symbol Period Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Errored Symbol Period Event asserted. When false the Errored Symbol Period Event is reset.
INT hh3cEponDeviceEventControl	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.24	INTEGER	read-write	Indicates and controls the resetting of the Event log. Setting this object to none(1) has no action resetLog(2) empties the event log. All data is deleted. Setting it to useDefaultReporting(3) returns all event priorities to their factory-default reporting. Reading this object always returns useDefaultReporting(3).
hh3cEponDeviceEventObjectEntry	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1		not-accessible	Table entries for Table of Event objects for EPON devices.
hh3cEponDeviceEventObjects	1.3.6.1.4.1.25506.2.42.4.1.1.3
hh3cEponDeviceEventObjectTable	1.3.6.1.4.1.25506.2.42.4.1.1.3.1		not-accessible	This table defines the Event Objects for EPON devices. The attributes are relevant for an OLT and an ONU.
C32 hh3cEponDeviceEventsLogCounts	1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.6	Counter32	read-only	The number of consecutive event instances reported by this entry. This starts at 1 with the creation of this row and increments by 1 for each subsequent duplicate event.
hh3cEponDeviceEventsLogEntry	1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1		not-accessible	A group of Events. Applications create and delete entries using hh3cEponDeviceEventsEntryStatus. When adding objects to a notification they are added in the lexical order of their index in this table.
ROW hh3cEponDeviceEventsLogEntryStatus	1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.8	RowStatus	read-create	The control that allows creation and deletion of entries. Once made active an entry MAY not be modified except to delete it.
DAT hh3cEponDeviceEventsLogFirstTime	1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.4	DateAndTime	read-only	The time that an entry was created.
OID hh3cEponDeviceEventsLogID	1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.3	OBJECT IDENTIFIER	read-create	The object identifier of a MIB module object to add to a Notification that results from the event. Writing can be done all the time.
U32 hh3cEponDeviceEventsLogIndex	1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.2	Unsigned32	not-accessible	An arbitrary integer for the purpose of identifying individual Events within a hh3cEponDeviceEventsLogName group. Events within a group are placed in the notification in the numerical order of this index.
DAT hh3cEponDeviceEventsLogLastTime	1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.5	DateAndTime	read-only	If multiple events are reported via the same entry, the time that the last event for this entry occurred, otherwise this should have the same value as hh3cEponDeviceEventsLogFirstTime.
STR hh3cEponDeviceEventsLogName	1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.1	SnmpAdminString	not-accessible	A locally-unique, administratively assigned name for a group of Events.
hh3cEponDeviceEventsLogTable	1.3.6.1.4.1.25506.2.42.4.1.1.3.2		not-accessible	A table of objects provides a log of notification based on the event as pointed to by entries in those tables. The intent is a MAC level event log (set of events to when they happened). This attribute is relevant for an OLT and an ONU.
INT hh3cEponDeviceEventsLogType	1.3.6.1.4.1.25506.2.42.4.1.1.3.2.1.7	INTEGER	read-only	A list of types for Events. Events are ordered according to their significance where 1 is the highest severity. hh3cEponDeviceDyingGaspAlarmState(1) indicates a Dying Gasp Alarm State, hh3cEponDeviceCriticalEventState(2) indicates a Critical Event State, hh3cEponDeviceLocalLinkFaultAlarmState(3) indicates a Local Link Fault Alarm State, hh3cEponDeviceTemperatureEventIndicationState(4) indicates a Temperature Event Indication State, hh3cEponDevicePowerVoltageEventIndicationState(5) indicates a Power Voltage Event Indication State, hh3cEponDeviceGlobalEventState(6) indicates a Global Event State, hh3cEponDeviceErroredSymbolPeriodEventState(7) indicates an Errored Symbol Period Event State, hh3cEponDeviceErroredFrameEventState(8) indicates an Errored Frame Event State, hh3cEponDeviceErroredFramePeriodEventState(9) indicates an Errored Frame Period Event State, hh3cEponDeviceErroredFrameSecondsSummaryEventState(10) indicates an Errored Frame Seconds Summary Event State, hh3cEponDeviceOrganizationSpecificEventState(11) indicates an Organization Specific Event State.
T/F hh3cEponDeviceGlobalEventEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.13	TruthValue	read-write	A control to allow GlobalEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
T/F hh3cEponDeviceGlobalEventState	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.12	TruthValue	read-only	A read-only variable, which defines the state of the Global Event indication of an EPON device. When the indication of the event input occurs the event is asserted. When the input is removed that event is de-asserted. When true the device has a Global Event asserted. When false the Global Event Indication is reset.
hh3cEponDeviceGroupControl	1.3.6.1.4.1.25506.2.42.4.1.2.1.1			A collection of objects of hh3cEponDevice control definition.
hh3cEponDeviceGroupEvent	1.3.6.1.4.1.25506.2.42.4.1.2.1.4			A collection of objects for EPON device Events
hh3cEponDeviceGroupEventLog	1.3.6.1.4.1.25506.2.42.4.1.2.1.5			A collection of objects for EPON device Events log
hh3cEponDeviceGroupRMadLTable	1.3.6.1.4.1.25506.2.42.4.1.2.1.2			A collection of objects of hh3cEponDevice remote Mac address to LLID table.
hh3cEponDeviceGroups	1.3.6.1.4.1.25506.2.42.4.1.2.1
hh3cEponDeviceGroupStat	1.3.6.1.4.1.25506.2.42.4.1.2.1.3			A collection of objects of EPON device Statistics
T/F hh3cEponDeviceLocalLinkFaultAlarmEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.7	TruthValue	read-write	A control to allow LocalLinkFaultAlarm event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
T/F hh3cEponDeviceLocalLinkFaultAlarmState	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.6	TruthValue	read-only	A read-only variable, which defines the state of the Local Link Fault indication of the OAM alarm indications as described in the [802.3ah] clause 57. When true the device has a Local Link Fault alarm asserted. When false the Local Link Fault alarm is reset.
hh3cEponDeviceMIB	1.3.6.1.4.1.25506.2.42.4			The objects in this MIB module are used to manage Ethernet Passive Optical Network (EPON) devices which are based on the Ethernet in the First Mile (EFM) PON as defined in IEEE Draft P802.3ah/D3.0 clause 60,64,65. This MIB is excerpted from the draft files directly,only changed the object name,added the hh3c as prefix. The following reference is used throughout this MIB module: [802.3ah] refers to: IEEE Draft P802.3ah/D3.3: 'Draft amendment to - Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications - Media Access Control Parameters, Physical Layers and Management Parameters for subscriber access networks', 22 April 2004. Of particular interest are Clause 64(MPCP) 65(P2mP RS) and 60 (PON PMDs). Clause 30, 'Management', and Clause 45,'Management Data Input/Output (MDIO) Interface'. Copyright (C) The Internet Society (2004). This version of this MIB module is part of XXXX see the RFC itself for full legal notices.
INT hh3cEponDeviceObjectDeviceReadyMode	1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.6	INTEGER	read-write	This variable defines the mode of an EPON device and provides information on the mode in initialization - ready for registration as defined by the [802.3ah] clause 64. When notReady(1) the device is not ready for operation. When inProcess(2) the device is in initialization process. When ready(3) the device is ready for registration. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
INT hh3cEponDeviceObjectFecEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.4	INTEGER	read-write	This variable defines and provides information whether the EPON device uses FEC as defined in the [802.3ah] clause 65.2 for EPON. When noFECEnabled(1) the device does not support FEC mode When fecTxEnabled(2) the device supports the FEC transmission mode. When fecRxEnabled(3) the device supports the FEC Receive mode. When fecTxRxEnabled(4) the device supports the FEC transmission and receive mode. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
hh3cEponDeviceObjectMIB	1.3.6.1.4.1.25506.2.42.4.1
INT hh3cEponDeviceObjectModes	1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.2	INTEGER	read-only	This variable defines the mode of the EPON device. When an olt(1) it is an Optical Line Terminal device (server) and when an onu(2) and Optical Network Unit device (client)
I32 hh3cEponDeviceObjectNumberOfLLIDs	1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.8	Integer32	read-only	A read only variable which defines the number of registered LLIDs (as defined by the [802.3ah] clause 65) in a EPON network for an OLT and an ONU. Initialization value is 0. This attribute is relevant for an OLT and an ONU.
INT hh3cEponDeviceObjectOamMode	1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.5	INTEGER	read-write	This variable defines and provides information on the Operation Administration and Maintenance (OAM) mode of an EPON device as defined by the [802.3ah] clause 57. When noOam(1) the device does not supports the OAM mode. When oamServer(2) the device supports the OAM mode as a server unit. When oamClient(3) the device supports the OAM mode as a client unit. Writing can be done during initialization, hh3cEponDeviceObjectDeviceReadyMode is in notReady(1) or inProcess(2). This attribute is relevant for an OLT and an ONU.
T/F hh3cEponDeviceObjectPowerDown	1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.7	TruthValue	read-write	Setting this variable to True(1) will cause Device to be entered into Power down mode where no registration is allowed and only receiving data from the link. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
I32 hh3cEponDeviceObjectReportThreshold	1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.9	Integer32	read-write	A set of 8 integers, for each LLID, that defines the threshold reporting for each Queue in the REPORT message, as defined in [802.3ah] 64. First Queue set reporting will provide information on the queue occupancy of frames below this Threshold. The value returned shall be in Time quanta (TQ) which is 16nsec or 2 octets increments. Writing can be done all the time. This attribute is relevant for an OLT and an ONU.
INT hh3cEponDeviceObjectReset	1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.1	INTEGER	read-write	This variable is used to reset the EPON device. The interface may be unavailable while the reset occurs and data may be lost. During reading operation it returns the state of the EPON device. running(1) indicates and operates normal operation, reset(2) indicates and operates reset mode. Writing can be done all the time.
hh3cEponDeviceObjects	1.3.6.1.4.1.25506.2.42.4.1.1
T/F hh3cEponDeviceOrganizationSpecificEventEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.23	TruthValue	read-write	A control to allow OrganizationSpecificEvent event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
T/F hh3cEponDeviceOrganizationSpecificEventState	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.22	TruthValue	read-only	A read-only variable, which defines the state of the Organization Specific Event indication of the OAM alarm TLV indications as described in the [802.3ah] clause 57.5.3. When true the device has an Organization Specific Event asserted. When false the Organization Specific Event is reset.
T/F hh3cEponDevicePowerVoltageEventIndicationEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.11	TruthValue	read-write	A control to allow PowerVoltageEventIndication event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
T/F hh3cEponDevicePowerVoltageEventIndicationState	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.10	TruthValue	read-only	A read-only variable, which defines the state of the Power/Voltage Event Indication of an EPON device. When condition of box Power/voltage is above the threshold defined the alarm is asserted. When the condition is below that threshold the alarm is de-asserted. When true the device has a Power/Voltage Event Indication asserted. When false the Power/Voltage Event Indication is reset.
INT hh3cEponDeviceRemoteMACAddressLLIDControl	1.3.6.1.4.1.25506.2.42.4.1.1.1.1.1.10	INTEGER	read-write	Indicates and controls the resetting of the LLID MAC address log. Setting this object to none(1) has no action resetLog(2) empties the LLID MAC address log. All data is deleted. Setting it to useDefaultReporting(3) returns all entries priorities to their factory-default reporting. Reading this object always returns useDefaultReporting(3).
hh3cEponDeviceRemoteMACAddressLLIDEntry	1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1		not-accessible	A group of entries. Applications create and delete entries using hh3cEponDeviceRMadlEntryStatus. When adding objects to an LLID they are added in the persistent order of their index in this table.
STR hh3cEponDeviceRemoteMACAddressLLIDName	1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.1	SnmpAdminString	read-create	A locally-unique, administratively assigned name for a group of entries.
hh3cEponDeviceRemoteMACAddressLLIDTable	1.3.6.1.4.1.25506.2.42.4.1.1.1.2		not-accessible	A table of read-only value that identifies the source_address and LLIDs parameter of the remote devices in the network. This MacAddress value, as defined in [802.3ah], 30.3.5.1.5, is updated on reception of a valid frame with a unicast destination Field or (1) a destination Field equal to the reserved multicast address for MAC Control specified in [802.3ah] Annex 31A, (2) lengthOrType field value equal to the reserved Type for MAC Control as specified in [802.3ah] Annex 31A. (3)an MPCP subtype value equal to the subtype reserved for MPCP as specified in [802.3ah] Annex 31A, and an LLID as allocated by the OLT. The table is defined as Remote MAC address - LLID (RMadL) The table is relevant only for an OLT device, and is equivalent from a bridge emulation to the bridge port-MAC address table where the LLIDs are equivalent to virtual bridge ports.
INT hh3cEponDeviceRMadlAction	1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.6	INTEGER	read-create	A list of actions for an entry - LLID. Indicates and defines the state of registration for the remote device. none(1) marks no action, register(2) marks to register an LLID, deregister(3) marks to deregister an LLID, reregister(4) marks reregistered LLID. Writing can be done all the time.
ROW hh3cEponDeviceRMadlEntryStatus	1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.7	RowStatus	read-create	The control that allows creation and deletion of entries. Once made active an entry MAY not be modified except to delete it.
U32 hh3cEponDeviceRMadlLLID	1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.2	Unsigned32	read-create	An arbitrary integer for the purpose of identifying the LLID. Writing can be done all the time.
OID hh3cEponDeviceRMadlLogID	1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.3	OBJECT IDENTIFIER	read-create	The object identifier of a MIB module object to add to an entry, indicating the entry ID in the table. Writing can be done all the time.
MAC hh3cEponDeviceRMadlRemoteAddress	1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.4	MacAddress	read-create	The remote MAC address of the LLID. Writing can be done all the time.
INT hh3cEponDeviceRMadlType	1.3.6.1.4.1.25506.2.42.4.1.1.1.2.1.5	INTEGER	read-create	A list of types for entries - LLIDs. Indicates and defines the state of registration. notRegister(1) marks a non registered LID, registered(2) marks a registered LLID. Writing can be done all the time.
I32 hh3cEponDeviceSampleMinimum	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.1	Integer32	read-write	The minimum Frequency of events this system will accept. A system may use the larger values of this minimum to lessen the impact of constant sampling. For larger sampling intervals the system samples less often and suffers less overhead. Unless explicitly resource limited, a system's value for this object SHOULD be 1, allowing as small as a 1 second interval for ongoing trigger sampling. Writing of the value can be done all the time.
C32 hh3cEponDeviceStatDroppedFramesQueue0	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.17	Counter32	read-only	A count of the number of times a -Queue-0- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatDroppedFramesQueue1	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.18	Counter32	read-only	A count of the number of times a -Queue-1- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatDroppedFramesQueue2	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.19	Counter32	read-only	A count of the number of times a -Queue-2- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatDroppedFramesQueue3	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.20	Counter32	read-only	A count of the number of times a -Queue-3- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatDroppedFramesQueue4	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.21	Counter32	read-only	A count of the number of times a -Queue-4- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatDroppedFramesQueue5	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.22	Counter32	read-only	A count of the number of times a -Queue-5- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatDroppedFramesQueue6	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.23	Counter32	read-only	A count of the number of times a -Queue-6- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatDroppedFramesQueue7	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.24	Counter32	read-only	A count of the number of times a -Queue-7- frames drops occurs. Increment the counter by one for each frame dropped from -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
hh3cEponDeviceStatEntry	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1		not-accessible	Table entries for Table of statistics counters of EPON devices.
hh3cEponDeviceStatObjects	1.3.6.1.4.1.25506.2.42.4.1.1.2
C32 hh3cEponDeviceStatRxFramesQueue0	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.9	Counter32	read-only	A count of the number of times a -Queue-0- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
C32 hh3cEponDeviceStatRxFramesQueue1	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.10	Counter32	read-only	A count of the number of times a -Queue-1- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
C32 hh3cEponDeviceStatRxFramesQueue2	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.11	Counter32	read-only	A count of the number of times a -Queue-2- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
C32 hh3cEponDeviceStatRxFramesQueue3	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.12	Counter32	read-only	A count of the number of times a -Queue-3- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
C32 hh3cEponDeviceStatRxFramesQueue4	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.13	Counter32	read-only	A count of the number of times a -Queue-4- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
C32 hh3cEponDeviceStatRxFramesQueue5	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.14	Counter32	read-only	A count of the number of times a -Queue-5- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
C32 hh3cEponDeviceStatRxFramesQueue6	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.15	Counter32	read-only	A count of the number of times a -Queue-6- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
C32 hh3cEponDeviceStatRxFramesQueue7	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.16	Counter32	read-only	A count of the number of times a -Queue-7- frames reception occurs. A single counter at the ONU and a set of counters, one for each LLID, at the OLT. Increment the counter by one for each frame received for each LLID, which is an output of -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU and an OLT.
hh3cEponDeviceStatTable	1.3.6.1.4.1.25506.2.42.4.1.1.2.1		not-accessible	This table defines the list of statistics counters of EPON devices. The attributes are relevant for an OLT and an ONU.
C32 hh3cEponDeviceStatTxFramesQueue0Ex	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.1	Counter32	read-only	A count of the number of times a -Queue-0- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-0-. The -Queue-0- marking matched the REPORT MPCP message Queue-0 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatTxFramesQueue1	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.2	Counter32	read-only	A count of the number of times a -Queue-1- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-1-. The -Queue-1- marking matched the REPORT MPCP message Queue-1 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatTxFramesQueue2	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.3	Counter32	read-only	A count of the number of times a -Queue-2- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-2-. The -Queue-2- marking matched the REPORT MPCP message Queue-2 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatTxFramesQueue3	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.4	Counter32	read-only	A count of the number of times a -Queue-3- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-3-. The -Queue-3- marking matched the REPORT MPCP message Queue-3 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatTxFramesQueue4	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.5	Counter32	read-only	A count of the number of times a -Queue-4- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-4-. The -Queue-4- marking matched the REPORT MPCP message Queue-4 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatTxFramesQueue5	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.6	Counter32	read-only	A count of the number of times a -Queue-5- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-5-. The -Queue-5- marking matched the REPORT MPCP message Queue-5 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatTxFramesQueue6	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.7	Counter32	read-only	A count of the number of times a -Queue-6- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-6-. The -Queue-6- marking matched the REPORT MPCP message Queue-6 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
C32 hh3cEponDeviceStatTxFramesQueue7	1.3.6.1.4.1.25506.2.42.4.1.1.2.1.1.8	Counter32	read-only	A count of the number of times a -Queue-7- frames transmission occurs. Increment the counter by one for each frame transmitted which is an output of -Queue-7-. The -Queue-7- marking matched the REPORT MPCP message Queue-7 field, as defined in [802.3ah] clause 64. This counter is mandatory for an ONU.
T/F hh3cEponDeviceTemperatureEventIndicationEnabled	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.9	TruthValue	read-write	A control to allow TemperatureEventIndication event to be used. When the value is true the event is sampled. When the value is false the event is not sampled. Writing can be done all the time.
T/F hh3cEponDeviceTemperatureEventIndicationState	1.3.6.1.4.1.25506.2.42.4.1.1.3.1.1.8	TruthValue	read-only	A read-only variable, which defines the state of the Temperature Event indication of an EPON device. When condition of box temperature is above the threshold defined the alarm is asserted. When the condition is below that threshold the alarm is de-asserted. When true the device has a Temperature Event Indication asserted. When false the Temperature Event Indication is reset.

RFC description

H3C Ethernet Passive Optical Network (EPON) device management based on IEEE 802.3ah standards.

Start monitoring H3C EPON OLT chassis (802.3ah device management) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HH3C-EPON-DEVICE-MIB