GDCSC613-MIB

All MIBs › GDCSC613-MIB

Category: Vendor: GDC

Description: General DataComm SC613 shelf controller MIB for enhanced chassis management and redundancy control.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is GDCSC613-MIB?

GDCSC613-MIB is a proprietary MIB from General DataComm for the SC613 shelf controller, a chassis management module used in telecom multiplexer/carrier shelves. It exposes card inventory/identification data, firmware code revision, alarm status, and configuration parameters such as receive-loss timeout, test pattern, and master transmit clock source. It is directly useful for monitoring both hardware and software status of the shelf, surfacing active alarm conditions (bql613AlarmStatus), confirming firmware revision (bql613CodeRev), identifying installed card types per slot (bql613WhatAreYouTable), and tracking clock-source redundancy state for the shelf's timing subsystem. As a self-contained legacy enterprise MIB it shows no apparent dependency on external standard MIBs. It is typically deployed in legacy telecom central-office or carrier shelves where SC613 controllers manage chassis alarms and clock redundancy. Engineers can download the GDCSC613-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in GDCSC613-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

General DataComm SC613 shelf/chassis controller
telecom multiplexer shelf

Monitoring Examples

An admin polls bql613AlarmStatus to detect active alarms on the shelf and bql613CodeRev to confirm the firmware revision of the controller card after a maintenance update. bql613MasterTXClkSrc indicates which clock source is currently acting as master, useful for spotting an unplanned failover in a redundant clocking scheme, while bql613WhatAreYouTable/Entry (indexed by bql613WhatAreYouIndex) identifies the installed card type in each slot.

What Can Be Monitored

alarm status
firmware code revision
card type per slot
master transmit clock source
test pattern configuration
receive-loss timeout

Imported Objects

From GDCMACRO-MIB

SCinstance

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
gdc	1.3.6.1.4.1.498
bql2	1.3.6.1.4.1.498.12
bql613	1.3.6.1.4.1.498.12.1
STR bql613MIBVersion	1.3.6.1.4.1.498.12.1.1	DisplayString	read-only	The version number of the MIB, to allow products to know which MIB is being supported. The version number will be x.yzT where x is a major revision (1-9), y is a minor revision(0-9), z is a typo revision (0-9) and T indicates the MIB is still a test revision(A-Z). When a release is complete no T should exist.
bql613WhatAreYouTable	1.3.6.1.4.1.498.12.1.2		not-accessible	The GDC SC613 What Are You Table.
bql613WhatAreYouEntry	1.3.6.1.4.1.498.12.1.2.1		not-accessible	An entry in the GDC SC613 What Are You table.
SCI bql613WhatAreYouIndex	1.3.6.1.4.1.498.12.1.2.1.1	SCinstance	read-only	This object is the identifier of the SC613 What Are You table.
STR bql613CodeRev	1.3.6.1.4.1.498.12.1.2.1.2	DisplayString	read-only	This function returns the firmware code level. Example A- ,B-
OCT bql613AlarmStatus	1.3.6.1.4.1.498.12.1.2.1.3	OCTET STRING	read-only	The current alarms of the unit without the alarm masks.
bql613ConfigTable	1.3.6.1.4.1.498.12.1.3		not-accessible	The GDC SC613.
bql613ConfigEntry	1.3.6.1.4.1.498.12.1.3.1		not-accessible	A listing of GDC 2B1Q SC613 options.
SCI bql613ConfigIndex	1.3.6.1.4.1.498.12.1.3.1.1	SCinstance	read-only	A unique index for the Configuration Table.
INT bql613TestPattern	1.3.6.1.4.1.498.12.1.3.1.2	INTEGER	read-write	Object to select loop and channel test pattern for SC613.
INT bql613RLTimeout	1.3.6.1.4.1.498.12.1.3.1.3	INTEGER	read-write	Object to select remote loop time out.
INT bql613MasterTXClkSrc	1.3.6.1.4.1.498.12.1.3.1.4	INTEGER	read-write	Object to option the Loop master transmit clock source.
INT bql613DTEDataRate	1.3.6.1.4.1.498.12.1.3.1.5	INTEGER	read-write	Object to option a SC613 Loop interface to a K bit per second rate.
INT bql613RespRdl	1.3.6.1.4.1.498.12.1.3.1.6	INTEGER	read-write	Object to option V54 Response RDL to enable or disable.
bql613DiagnosticTable	1.3.6.1.4.1.498.12.1.4		not-accessible	The GDC SC613 diagnostics table.
bql613DiagnosticEntry	1.3.6.1.4.1.498.12.1.4.1		not-accessible	A listing of GDC SC613 diagnostic tests
SCI bql613DiagnosticIndex	1.3.6.1.4.1.498.12.1.4.1.1	SCinstance	read-only	A unique index for the Diagnostic Table.
INT bql613DiagnosticTest	1.3.6.1.4.1.498.12.1.4.1.2	INTEGER	read-write	This function selects or reads the test. 0 = no test currently operating 1 = remote loopback test 2 = channel loopback test 4 = data loopback test 8 = selftest 16 = line loopback test 32 = terminate test All other values are test combinations such as 9 = selftest and remote loopback.
INT bql613DiagnosticActive	1.3.6.1.4.1.498.12.1.4.1.3	INTEGER	read-only	This function represents the test condition.
INT bql613DiagnosticResults	1.3.6.1.4.1.498.12.1.4.1.4	INTEGER	read-only	This function reads the self test results in bit errors.
INT bql613DiagnosticErrorCount	1.3.6.1.4.1.498.12.1.4.1.5	INTEGER	read-write	This function resets the selftest error count for a SC613.
bql613ControlTable	1.3.6.1.4.1.498.12.1.6		not-accessible	The GDC SC613 Control Table.
bql613ControlEntry	1.3.6.1.4.1.498.12.1.6.1		not-accessible	An entry in the GDC SC613 Control table.
SCI bql613ControlIndex	1.3.6.1.4.1.498.12.1.6.1.1	SCinstance	read-only	This object is the identifier of the SC613 Control table.
INT bql613SoftReset	1.3.6.1.4.1.498.12.1.6.1.2	INTEGER	read-write	Forces a soft reset on the network element. The reset selection is write only. The normal selection is read only.
INT bql613EraseConfig	1.3.6.1.4.1.498.12.1.6.1.3	INTEGER	read-write	Forces an erase of the stored configuration in the network element. The erase selection is write only. The normal selection is read only.
INT bql613FrontPanel	1.3.6.1.4.1.498.12.1.6.1.4	INTEGER	read-write	Object used to enable or disable the units front panel switches.
OCT bql613LEDStatus	1.3.6.1.4.1.498.12.1.6.1.5	OCTET STRING	read-only	The GDC SC613 front panel LED Status. A value of 1 means on, 0 is off. byte 1 bit 7 (1.7) - not used 1.6 - test mode 1.5 - alarm on 1.4 - loop 1 line loopback 1.3 - loop 1 send data transitions 1.2 - loop 1 receive data transitions 1.1 - loop 1 request to send 1.0 - loop 1 data carrier on 2.7 - not used 2.6 - not used 2.5 - not used 2.4 - loop 2 line loopback 2.3 - loop 2 send data transitions 2.2 - loop 2 receive data transitions 2.1 - loop 2 request to send 2.0 - loop 2 data carrier on 3.7 - not used 3.6 - not used 3.5 - not used 3.4 - loop 3 line loopback 3.3 - loop 3 send data transitions 3.2 - loop 3 receive data transitions 3.1 - loop 3 request to send 3.0 - loop 3 data carrier on
bql613CurrentTable	1.3.6.1.4.1.498.12.1.7		not-accessible	The SC613 Current table.
bql613CurrentEntry	1.3.6.1.4.1.498.12.1.7.1		not-accessible	An entry in the SC613 Current table.
SCI bql613CurrentIndex	1.3.6.1.4.1.498.12.1.7.1.1	SCinstance	read-only	The index value which uniquely identifies the SC613 interface to which this entry is applicable.
OCT bql613CurrentStats	1.3.6.1.4.1.498.12.1.7.1.2	OCTET STRING	read-only	The number of Errored Seconds, Severely Errored Seconds & Unavailable Errored Seconds encountered by an ISDN interface in the current 15 minute interval.
bql613IntervalTable	1.3.6.1.4.1.498.12.1.8		not-accessible	The SC613 Interval table.
bql613IntervalEntry	1.3.6.1.4.1.498.12.1.8.1		not-accessible	An entry in the SC613 Interval table.
SCI bql613IntervalIndex	1.3.6.1.4.1.498.12.1.8.1.1	SCinstance	read-only	The index value which uniquely identifies the ISDN interface to which this entry is applicable.
INT bql613IntervalNumber	1.3.6.1.4.1.498.12.1.8.1.2	INTEGER	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minute inter- val (assuming that all 96 intervals are valid).
OCT bql613IntervalStats	1.3.6.1.4.1.498.12.1.8.1.3	OCTET STRING	read-only	The number of Errored Seconds, Severely Errored Seconds and Unavailable Errored Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
bql613TotalTable	1.3.6.1.4.1.498.12.1.9		not-accessible	The SC613 Total table. 24 hour interval.
bql613TotalEntry	1.3.6.1.4.1.498.12.1.9.1		not-accessible	An entry in the SC613 Total table.
SCI bql613TotalIndex	1.3.6.1.4.1.498.12.1.9.1.1	SCinstance	read-only	The index value which uniquely identifies the ISDN interface to which this entry is applicable.
OCT bql613TotalStats	1.3.6.1.4.1.498.12.1.9.1.2	OCTET STRING	read-only	The number of Errored Seconds,Severely Errored Seconds & Unavailable Errored Seconds encountered by an ISDN interface in the previous 24 hour interval.
bql613IntervalMaintenanceTable	1.3.6.1.4.1.498.12.1.10		not-accessible	The SC613 Loop Interval Maintenance table.
bql613IntervalMaintenanceEntry	1.3.6.1.4.1.498.12.1.10.1		not-accessible	The SC613 Interval Maintenance table entry.
SCI bql613IntervalMaintenanceIndex	1.3.6.1.4.1.498.12.1.10.1.1	SCinstance	read-only	The index value which uniquely identifies the interface to which this entry is applicable. This has the form of a SCinstance which defines the slot, line, drop, and interface, where is can be 1, 2, or 3.
INT bql613ResetIntervals	1.3.6.1.4.1.498.12.1.10.1.2	INTEGER	read-write	This variable is used to reset Loop performance intervals. When it is set to reset, the Loop performance tables are reset to zero.
INT bql613NumberofValidIntervals	1.3.6.1.4.1.498.12.1.10.1.3	INTEGER	read-only	This variable is used to read the number of intervals collected. Each interval is an increment of 15 minutes.
INT bql613ResetMajorAlarm	1.3.6.1.4.1.498.12.1.10.1.4	INTEGER	read-write	This variable is used to reset alarm per Loop basis.
INT bql613ResetMinorAlarm	1.3.6.1.4.1.498.12.1.10.1.5	INTEGER	read-write	This variable is used to reset alarm per Loop basis.
bql613Alarm	1.3.6.1.4.1.498.12.7
bql613AlarmData	1.3.6.1.4.1.498.12.7.1
bql613NoResponseAlm	1.3.6.1.4.1.498.12.7.1.1
bql613DiagRxErrAlm	1.3.6.1.4.1.498.12.7.1.2
bql613PowerUpAlm	1.3.6.1.4.1.498.12.7.1.3
bql613Lp2B1QOutofSyncAlm	1.3.6.1.4.1.498.12.7.1.4
bql613LpTxClockOutOfTolerance	1.3.6.1.4.1.498.12.7.1.5
bql613LpExtTxClkAlm	1.3.6.1.4.1.498.12.7.1.6
bql613LpSealingCurrentNoContinuityAlm	1.3.6.1.4.1.498.12.7.1.7
bql613LpMajorBERAlm	1.3.6.1.4.1.498.12.7.1.8
bql613LpMinorBERAlm	1.3.6.1.4.1.498.12.7.1.9
bql613AlarmConfigTable	1.3.6.1.4.1.498.12.7.2		not-accessible	The bql613AlarmConfigTable contains entries that configure alarm reporting. The structure of the table is such that alarm configuration is supported on a unit and interface basis, and then on an alarm type basis within the interface. For simplicity sake alarms, be they unit or interface related, are represented in one table.
bql613AlarmConfigEntry	1.3.6.1.4.1.498.12.7.2.1		not-accessible	An entry in the bql613AlarmConfigTable table.
SCI bql613AlarmConfigIndex	1.3.6.1.4.1.498.12.7.2.1.1	SCinstance	read-only	The index value which uniquely identifies the interface to which this entry is applicable.
OID bql613AlarmConfigIdentifier	1.3.6.1.4.1.498.12.7.2.1.2	OBJECT IDENTIFIER	read-only	The unique alarm identifier assigned to this alarm type. The format of this identifier is an OBJECT IDENTIFIER that has the following format: {iso(1) org(3) dod(6) internet(1) private(4) enterprises(1) gdc(498) xxx(x) alarm(z) yyy(y) where xxx(x) is the administratively assigned family object identifier (z) is the object identifier for alarms in the family defined MIB and yyy(y) is the administratively assigned alarm type identifier for this alarm.
INT bql613AlarmThreshold	1.3.6.1.4.1.498.12.7.2.1.3	INTEGER	read-write	This function sets/reads the Major or Minor BER alarm threshold criteria.

RFC description

GDC SC613 ISDN 2B1Q device management covering network element information and ISDN interface configuration.

Start monitoring General DataComm (GDC) SC613 shelf/chassis controller with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download GDCSC613-MIB

What Is GDCSC613-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description