FRX-MIB

All MIBs › FRX-MIB

Description: FRX-MIB module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is FRX-MIB?

FRX-MIB is a legacy vendor MIB (associated with Netrix/FastComm-style FRX frame relay switch/multiplexer nodes) that manages and monitors a frame relay switching node, covering hardware identity, software version, and node-level operational state alongside protocol-specific groups for network protocols such as SPX/IPX and LAT-style extensions (net, spx, lwx). It exposes clear hardware/software status objects: nodeSoftwareRelease and nodeSoftwareReleaseDate report the running firmware version, nodeBootVersion and nodeCardType identify the boot code and installed card type, and nodeUpTime tracks how long the node has been running since last restart. Operationally it also reports nodeCongestionLevel and nodeBuffersUsed, giving direct visibility into frame relay network congestion and buffer exhaustion, both classic causes of frame relay service degradation. It predates modern standard frame-relay MIBs and is largely self-contained, though nodeIPAddress ties it into standard IP addressing conventions. It was deployed on legacy frame relay switch/access nodes in carrier or enterprise WAN frame relay networks. Engineers can download the FRX-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in FRX-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

legacy frame relay switch/access node (Netrix/FastComm-style FRX platform)

Monitoring Examples

An administrator would poll nodeUpTime and nodeSoftwareRelease/nodeSoftwareReleaseDate to confirm a node hasn't unexpectedly rebooted and is running the expected firmware version. nodeCongestionLevel and nodeBuffersUsed would be watched together - a high congestion level paired with high buffer usage on a node indicates the frame relay switch is nearing capacity and may start dropping or marking frames as discard-eligible. nodeCardType and nodeBootVersion would be checked after a hardware swap to confirm the replacement card and boot image match expectations.

What Can Be Monitored

node uptime
software release version and date
boot version
card type
network congestion level
buffer utilization

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
net	1.3.6.1.4.1.177
spx	1.3.6.1.4.1.177.1
lwx	1.3.6.1.4.1.177.2
frx	1.3.6.1.4.1.177.3
NTF systemRestartTrap	1.3.6.1.4.1.177.3.0.1			This trap is sent when the system restarts for any reason other than an operator requested restart.
NTF systemSyserrTrap	1.3.6.1.4.1.177.3.0.2			This trap is sent when the system detects a inconsistency. This may cause a reset of the FRX node.
NTF configChangedTrap	1.3.6.1.4.1.177.3.0.3			This trap is sent when a new configuration is saved in the non-volatile storage.
NTF nodeCongestedTrap	1.3.6.1.4.1.177.3.0.4			This trap is sent when the FRX node becomes congested.
NTF portInstalledTrap	1.3.6.1.4.1.177.3.0.5			This trap is sent when a port is installed.
NTF portDeletedTrap	1.3.6.1.4.1.177.3.0.6			This trap is sent when a port is deleted.
NTF portActivatedTrap	1.3.6.1.4.1.177.3.0.7			This trap is sent when a port is activated.
NTF portDisabledTrap	1.3.6.1.4.1.177.3.0.8			This trap is sent when a port is disabled.
NTF portCongestedTrap	1.3.6.1.4.1.177.3.0.9			This trap is sent when a port is congested.
NTF pvcInstalledTrap	1.3.6.1.4.1.177.3.0.10			This trap is sent when a virtual circuit is installed.
NTF pvcDeletedTrap	1.3.6.1.4.1.177.3.0.11			This trap is sent when a virtual circuit is deleted.
NTF pvcActivatedTrap	1.3.6.1.4.1.177.3.0.12			This trap is sent when a virtual circuit is activated.
NTF pvcDisabledTrap	1.3.6.1.4.1.177.3.0.13			This trap is sent when a virtual circuit is disabled.
NTF pvcStatusActiveTrap	1.3.6.1.4.1.177.3.0.14			This trap is sent when the status for a virtual circuit become active.
NTF pvcStatusInactiveTrap	1.3.6.1.4.1.177.3.0.15			This trap is sent when the status for a virtual circuit become inactive.
NTF cbusUpTrap	1.3.6.1.4.1.177.3.0.16			This trap is sent when the CBUS interface is ready for use.
NTF cbusDownTrap	1.3.6.1.4.1.177.3.0.17			This trap is sent when the CBUS interface becomes invalid.
NTF serialFailTrap	1.3.6.1.4.1.177.3.0.18			This trap is sent when an HDLC port fails to initialize.
NTF portUniActiveTrap	1.3.6.1.4.1.177.3.0.19			This trap is sent when a port's UNI protocol becomes active.
NTF portUniInactiveTrap	1.3.6.1.4.1.177.3.0.20			This trap is sent when a port's UNI protocol becomes inactive.
NTF portIDNXCallUpTrap	1.3.6.1.4.1.177.3.0.21			This trap is sent when a port's IDNX call (bandwidth) is available.
NTF portIDNXCallDownTrap	1.3.6.1.4.1.177.3.0.22			This trap is sent when a port's IDNX call (bandwidth) becomes unavailable.
NTF nodeNotCongestedTrap	1.3.6.1.4.1.177.3.0.23			This trap is sent when a FRX node goes from being congested to not being congested.
NTF portNotCongestedTrap	1.3.6.1.4.1.177.3.0.24			This trap is sent when a port goes from being congested to not being congested.
NTF operatorResetTrap	1.3.6.1.4.1.177.3.0.25			This trap is sent when the operator requests a reset of the FRX.
NTF eventLogClearedTrap	1.3.6.1.4.1.177.3.0.26			This trap is sent when the operator requests to clear the FRX event log.
NTF configClearedTrap	1.3.6.1.4.1.177.3.0.27			This trap is sent when the operator requests to clear the configuration of an FRX.
NTF functionMismatchTrap	1.3.6.1.4.1.177.3.0.28			This trap is sent when the code type (FRX) does not match the value stored in the IDNX database.
NTF eventLogErrorTrap	1.3.6.1.4.1.177.3.0.29			This trap is sent when the FRX is unable to create an event log.
NTF encapActiveTrap	1.3.6.1.4.1.177.3.0.30			This trap is sent when frame relay encapsulation is turned on for a PVC.
NTF encapInactiveTrap	1.3.6.1.4.1.177.3.0.31			This trap is sent when frame relay encapsulation is turned off for a PVC.
NTF altPathUsedTrap	1.3.6.1.4.1.177.3.0.32			This trap is sent when a path alternate to the preferred path is used to setup a pvc.
NTF pvcStateIdleTrap	1.3.6.1.4.1.177.3.0.33			The state of a PVC describes the current status of call setup. This trap is sent when a PVC's state changes to Idle.
NTF pvcStateSetupTrap	1.3.6.1.4.1.177.3.0.34			The state of a PVC describes the current status of call setup. This trap is sent when a PVC's state changes to Setup.
NTF pvcStateCompleteTrap	1.3.6.1.4.1.177.3.0.35			The state of a PVC describes the current status of call setup. This trap is sent when a PVC's state changes to Complete.
NTF pvcStateDisconnectTrap	1.3.6.1.4.1.177.3.0.36			The state of a PVC describes the current status of call setup. This trap is sent when a PVC's state changes to Disconnect.
NTF billingDownloadSuccessTrap	1.3.6.1.4.1.177.3.0.37			A Billing file was successfully downloaded from the FRX.
NTF billingDownloadFailureTrap	1.3.6.1.4.1.177.3.0.38			An error occurred while the FRX attempted to download a Billing file.
NTF billingDownloadThresholdTrap	1.3.6.1.4.1.177.3.0.39			An attempt was made to set an obsolete Billing download threshold parameter.
NTF configSyntaxErrorTrap	1.3.6.1.4.1.177.3.0.40			A line in the FRX configuration file had a syntax error when it was loaded; the line was ignored.
NTF configDownloadSuccessTrap	1.3.6.1.4.1.177.3.0.41			A Configuration file was successfully downloaded from the FRX.
NTF configDownloadFailureTrap	1.3.6.1.4.1.177.3.0.42			An error occurred while the FRX attempted to download a Configuration file.
NTF nodeFlashMemErr	1.3.6.1.4.1.177.3.0.50			This trap indicates that a code checksum error occurred in Flash.
NTF nodeFlashWriteErr	1.3.6.1.4.1.177.3.0.51			This trap indicates that a code transfer to Flash occurred. Flash may now be corrupted.
NTF nodeUserLogin	1.3.6.1.4.1.177.3.0.52			A user has logged into the FRX through the serial console or network.
NTF nodeUserLogout	1.3.6.1.4.1.177.3.0.53			A user has logged out.
NTF dsx1NoAlarm	1.3.6.1.4.1.177.3.0.54			No alarm present.
NTF dsx1RcvFarEndLOF	1.3.6.1.4.1.177.3.0.55			Far end LOF (a.k.a. Yellow Alarm).
NTF dsx1RcvFarEndLOFEnded	1.3.6.1.4.1.177.3.0.56			Far end LOF (a.k.a. Yellow Alarm) indication has ended.
NTF dsx1XmtFarEndLOF	1.3.6.1.4.1.177.3.0.57			Near end sending LOF Indication.
NTF dsx1XmtFarEndLOFEnding	1.3.6.1.4.1.177.3.0.58			Near end ending LOF Indication.
NTF dsx1RcvAIS	1.3.6.1.4.1.177.3.0.59			Far end sending AIS.
NTF dsx1RcvAISEnded	1.3.6.1.4.1.177.3.0.60			Far end AIS has ceased.
NTF dsx1XmtAIS	1.3.6.1.4.1.177.3.0.61			Near end sending AIS indication.
NTF dsx1XmtAISEnding	1.3.6.1.4.1.177.3.0.62			Near end ending AIS indication.
NTF dsx1LossOfFrame	1.3.6.1.4.1.177.3.0.63			Near end LOF (a.k.a. Red Alarm).
NTF dsx1LossOfFrameEnded	1.3.6.1.4.1.177.3.0.64			Near end LOF (a.k.a. Red Alarm) indication has ended.
NTF dsx1LossOfSignal	1.3.6.1.4.1.177.3.0.65			Near end Loss Of Signal.
NTF dsx1LossOfSignalEnded	1.3.6.1.4.1.177.3.0.66			Near end Loss Of Signal indication has ended.
NTF dsx1LoopbackState	1.3.6.1.4.1.177.3.0.67			Near end is looped.
NTF dsx1LoopbackStateEnded	1.3.6.1.4.1.177.3.0.68			Near end is un-looped.
NTF dsx1T16AIS	1.3.6.1.4.1.177.3.0.69			E1 TS16 AIS indication received.
NTF dsx1T16AISEnded	1.3.6.1.4.1.177.3.0.70			E1 TS16 AIS indication has ended.
NTF dsx1RcvFarEndLOMF	1.3.6.1.4.1.177.3.0.71			Far End sending TS16 LOMF.
NTF dsx1RcvFarEndLOMFEnded	1.3.6.1.4.1.177.3.0.72			Far End ending TS16 LOMF.
NTF dsx1XmtFarEndLOMF	1.3.6.1.4.1.177.3.0.73			Near End sending TS16 LOMF.
NTF dsx1XmtFarEndLOMFEnding	1.3.6.1.4.1.177.3.0.74			Near End ending TS16 LOMF.
NTF dsx1RcvTestCode	1.3.6.1.4.1.177.3.0.75			Near End detected a test code.
NTF dsx1OtherFailure	1.3.6.1.4.1.177.3.0.76			Unknown line status received.
NTF nodeAlarmedPortsZero	1.3.6.1.4.1.177.3.0.77			The value of nodeAlarmedPorts became zero.
NTF portAlarmedPVCsZero	1.3.6.1.4.1.177.3.0.78			The value of portAlarmedPVCs for this port became zero.
NTF operatorInstallTrap	1.3.6.1.4.1.177.3.0.79			This trap is sent when a new operator is installed.
NTF operatorDeleteTrap	1.3.6.1.4.1.177.3.0.80			This trap is sent when an operator is deleted.
NTF portPVCReOptimizationStart	1.3.6.1.4.1.177.3.0.81			This trap is sent when PVC ReOptimization has started.
NTF portPVCReOptimizationEnd	1.3.6.1.4.1.177.3.0.82			This trap is sent when PVC ReOptimization has ended.
globals	1.3.6.1.4.1.177.3.1
INT mibVersion	1.3.6.1.4.1.177.3.1.1	INTEGER	read-only	The version number of this FRX MIB.
INT mibEditVersion	1.3.6.1.4.1.177.3.1.2	INTEGER	read-only	The edit version (sub version) number of this FRX MIB.
node	1.3.6.1.4.1.177.3.2
STR nodeIdnxAddress	1.3.6.1.4.1.177.3.2.1	DisplayString	read-only	The IDNX Address of this PX card, e.g. NxCy.
STR nodeSoftwareRelease	1.3.6.1.4.1.177.3.2.2	DisplayString	read-only	The release of FRX code running on this PX card, e.g. Release 2.01.01 Version 81.01.
STR nodeSoftwareReleaseDate	1.3.6.1.4.1.177.3.2.3	DisplayString	read-only	The date the FRX code was built, e.g. Wed Feb 10 14:12:24 PST 1993 by tee.
STR nodeBootVersion	1.3.6.1.4.1.177.3.2.4	DisplayString	read-only	The version of boot prom on the PX card.
STR nodeCardType	1.3.6.1.4.1.177.3.2.5	DisplayString	read-only	The type of PX card running the FRX code.
STR nodeUpTime	1.3.6.1.4.1.177.3.2.6	DisplayString	read-only	The amount of time the FRX has been alive.
INT nodeCongestionLevel	1.3.6.1.4.1.177.3.2.7	INTEGER	read-only	The current state of congestion for the FRX node. The valid values are notCongested (normal operation), approachingCongestion (FECN and BECN are being set), congested (DE frames are being dropped), and fullyCongested (normal data frames are being dropped).
INT nodeBuffersUsed	1.3.6.1.4.1.177.3.2.8	INTEGER	read-only	The number of system buffers being used.
INT nodeNumberHDLCPorts	1.3.6.1.4.1.177.3.2.9	INTEGER	read-only	The number of HDLC ports the hardware supports.
IP nodeIPAddress	1.3.6.1.4.1.177.3.2.10	IpAddress	read-only	The IP Address of this FRX Node.
IP nodeNetworkMask	1.3.6.1.4.1.177.3.2.11	IpAddress	read-write	The IP network mask for this FRX Node.
INT nodeBackcard	1.3.6.1.4.1.177.3.2.12	INTEGER	read-write	Enables or disables the backcard on the FRX node. The backcard must be enabled for gateway functionality. Note: If the backcard is not physically present, an attempt to enable it will result in an error.
INT nodeBackcardType	1.3.6.1.4.1.177.3.2.13	INTEGER	read-only	The type of backcard interface installed.
STR nodeBackcardSerialNumber	1.3.6.1.4.1.177.3.2.14	DisplayString	read-only	The serial number and revision of the backcard interface.
INT nodeBillingDownloads	1.3.6.1.4.1.177.3.2.15	INTEGER	read-write	Enables or disables billing record downloads to an NMS workstation from this FRX node.
INT nodeConfigurationDownloads	1.3.6.1.4.1.177.3.2.16	INTEGER	read-write	Enables or disables configuration record downloads to an NMS workstation from this FRX node.
INT nodeFrameCounterThreshold	1.3.6.1.4.1.177.3.2.17	INTEGER	not-accessible	A threshold that causes a billing record to be downloaded when a frame counter exceeds its value.
INT nodeByteCounterThreshold	1.3.6.1.4.1.177.3.2.18	INTEGER	not-accessible	A threshold that causes a billing record to be downloaded when a byte counter exceeds its value.
nodeBillingTimeTable	1.3.6.1.4.1.177.3.2.19		not-accessible	The list of times to download billing records to an NMS workstation.
nodeBillingTimeEntry	1.3.6.1.4.1.177.3.2.19.1		not-accessible	A row from the billing download time table.
OCT downloadTime	1.3.6.1.4.1.177.3.2.19.1.1	OCTET STRING	read-write	A time of day at which billing records for the node are sent to an NMS workstation.
INT downloadTimeRowStatus	1.3.6.1.4.1.177.3.2.19.1.2	INTEGER	read-write	Controls row deletion for this table. Setting to invalid deletes the row from the table.
INT downloadTimeIndex	1.3.6.1.4.1.177.3.2.19.1.3	INTEGER	read-only	The index into the billing time table.
nodeNMSWorkstationTable	1.3.6.1.4.1.177.3.2.20		not-accessible	The list of workstations that are downloaded with billing and configuration records.
nodeNMSWorkstationEntry	1.3.6.1.4.1.177.3.2.20.1		not-accessible	A row from the NMS workstation download target list.
IP nmsWorkstationAddress	1.3.6.1.4.1.177.3.2.20.1.1	IpAddress	read-write	The IP address of an NMS workstation that billing and configuration records get downloaded to.
INT nmsWorkstationInetPort	1.3.6.1.4.1.177.3.2.20.1.2	INTEGER	read-write	The internet port on which the special TFTP server on an NMS workstation will listen for requests to download billing and configuration records.
INT nmsWorkstationRowStatus	1.3.6.1.4.1.177.3.2.20.1.3	INTEGER	read-write	Controls row deletion for this table. Setting to invalid deletes the row from the table.
INT nodeNumberTBUSPorts	1.3.6.1.4.1.177.3.2.21	INTEGER	read-only	The number of TBus ports the hardware supports.
INT nodeBackcardWanIF	1.3.6.1.4.1.177.3.2.22	INTEGER	read-write	Enables or disables the backcard WAN I/F on the FRX node. The backcard must be enabled for WAN port functionality. Note: If the backcard is not physically present, an attempt to enable it will result in an error.
GAU nodeAlarmedPorts	1.3.6.1.4.1.177.3.2.23	Gauge	read-only	The number of front or backcard ports on this node where any of the following conditions is true: - portTBusState (or T1 Status for backcard ports) is 'down' - portUNIState is 'down' - portAlarmedPVCs is not zero.
STR nodeBackcardHardwareAddress	1.3.6.1.4.1.177.3.2.24	DisplayString	read-only	The hardware address of the backcard interface.
port	1.3.6.1.4.1.177.3.3
portConfTable	1.3.6.1.4.1.177.3.3.1		not-accessible	A table of this FRX's port configuration. Before attempting to modify any variables in this table, the port must be disabled (set portConfState = 'disable').
portConfEntry	1.3.6.1.4.1.177.3.3.1.1		not-accessible	An entry (conceptual row) in the port configuration table.
INT portConfEntryId	1.3.6.1.4.1.177.3.3.1.1.1	INTEGER	read-only	The port identifier (number) for this port.
INT portConfState	1.3.6.1.4.1.177.3.3.1.1.2	INTEGER	read-write	Performs the enumerated action on the port. That is to say, setting the value to delete will cause the port to be deleted, etc. This variable must be set to 'disable' before any other port configuration variables can be modified.
INT portInterfaceProtocol	1.3.6.1.4.1.177.3.3.1.1.3	INTEGER	read-write	Determines the function of the port, including which UNI protocol is to be used. All values except interNode are for ports at access points into the network. InterNode is for ports internal to the network. AnsiNetwork, ansiUser, and ansiNNI conform to procedures specified in the ANSI T1.617 Annex D specification. ccittNetwork, ccittUser, and ccittNNI conform to procedures specified in the CCITT Q.933 Annex A specification. lmiNetwork, lmiUser, and lmiNNI conform to procedures specified in the DEC, Northern Telecom, StratCom specification.
INT portKeepaliveVerif	1.3.6.1.4.1.177.3.3.1.1.4	INTEGER	read-write	Enables or disables keepalive verification. This parameter is applicable when the portInterfaceProtocol is interNode.
INT portBackupInterNodal	1.3.6.1.4.1.177.3.3.1.1.5	INTEGER	read-write	Enables or disables using this port as a backup Inter-Nodal port. This parameter is applicable when the portInterfaceProtocol is interNode.
INT portExternalFrTrunk	1.3.6.1.4.1.177.3.3.1.1.6	INTEGER	read-write	Enables or disables the External Frame Relay Trunk feature.
INT portUniExternalFrTrunk	1.3.6.1.4.1.177.3.3.1.1.7	INTEGER	read-write	The UNI protocol to use when the External Frame Relay Trunk feature is enabled.
INT portDlciExternalFrTrunk	1.3.6.1.4.1.177.3.3.1.1.8	INTEGER	read-write	The DLCI of the PVC that is in use at the UNI when the External Frame Relay Trunk feature is enabled.
INT portLinkIntegVerif	1.3.6.1.4.1.177.3.3.1.1.9	INTEGER	read-write	Determines whether this port will react to problems detected by a UNI protocol. This parameter is applicable if the portInterfaceProtocol is ansi, ccitt, or lmi*.
INT portAsyncPVCStatus	1.3.6.1.4.1.177.3.3.1.1.10	INTEGER	read-write	Determines whether this port should send Asynchronous PVC status messages. This parameter is applicable if the portInterfaceProtocol is ansiNetwork, ansiNNI, ccittNetwork, or ccittNNI.
INT portN391Counter	1.3.6.1.4.1.177.3.3.1.1.11	INTEGER	read-write	The value for N391, the full status polling counter.
INT portN392Counter	1.3.6.1.4.1.177.3.3.1.1.12	INTEGER	read-write	The value for N392, the error threshold counter.
INT portN393Counter	1.3.6.1.4.1.177.3.3.1.1.13	INTEGER	read-write	The value for N393, the monitored events counter.
INT portT391Timer	1.3.6.1.4.1.177.3.3.1.1.14	INTEGER	read-write	The value for T391, the link integrity polling timer.
INT portT392Timer	1.3.6.1.4.1.177.3.3.1.1.15	INTEGER	read-write	The value for T392, the polling verification timer.
INT portSdlcEncapMode	1.3.6.1.4.1.177.3.3.1.1.16	INTEGER	read-write	Selects which encapsulation mode to be used when the portInterfacePrococol is sdlcHdlcEncap.
INT portSdlcEncapDefaultDlci	1.3.6.1.4.1.177.3.3.1.1.17	INTEGER	read-write	Specifies which DLCI will be used to encapsulate received SDLC/HDLC frames at the entry to the network. This parameter is applicable if the portInterfaceProtocol is sdlcHdlcEncap and the encapsulation mode is transparent.
INT portAddrMapDefaultDlci	1.3.6.1.4.1.177.3.3.1.1.18	INTEGER	read-write	Specifies which DLCI will be used to encapsulate received SDLC/HDLC frames at the entry to the network. This parameter is applicable if the portInterfaceProtocol is sdlcHdlcEncap and the encapsulation mode is address-mapped.
INT portPriorityQueuing	1.3.6.1.4.1.177.3.3.1.1.19	INTEGER	read-write	Enables or disables priority queuing on a port.
INT portAccountingPerDlci	1.3.6.1.4.1.177.3.3.1.1.20	INTEGER	read-write	Enables or disables accounting per DLCI on a port. Enabling this feature may seriously degrade performance in systems with high speed (greater than 1.024 Mbps) ports. Frames may be lost.
INT portPVCOptimization	1.3.6.1.4.1.177.3.3.1.1.21	INTEGER	read-write	Enables or disables route optimization per DLCI on a port. Enabling this feature may seriously degrade performance in systems with high speed (greater than 1.024 Mbps) ports. Frames may be lost.
portStatusTable	1.3.6.1.4.1.177.3.3.2		not-accessible	A table of this node's port status and statistics.
portStatusEntry	1.3.6.1.4.1.177.3.3.2.1		not-accessible	The port status and statistics table.
INT portDataBaseState	1.3.6.1.4.1.177.3.3.2.1.1	INTEGER	read-only	The state of the port in the database. The values are active and disabled.
INT portTBusState	1.3.6.1.4.1.177.3.3.2.1.2	INTEGER	read-only	The state of the TBus connection for this port. The values are up and down.
INT portUNIState	1.3.6.1.4.1.177.3.3.2.1.3	INTEGER	read-only	The state of the UNI for this port. The valid values are up and down.
INT portNumberEstablishedCircuits	1.3.6.1.4.1.177.3.3.2.1.4	INTEGER	read-only	The number of virtual circuits on this port in state Complete.
INT portNumberTotalCircuits	1.3.6.1.4.1.177.3.3.2.1.5	INTEGER	read-only	The total number of virtual circuits on this port, regardles of state.
INT portRxCongestState	1.3.6.1.4.1.177.3.3.2.1.6	INTEGER	read-only	The congestion state of the port's receiver. The valid values are notCongested (normal operation), approachingCongestion (FECN and BECN are being set), congested (DE frames are being dropped), and fullyCongested (normal data frames are being dropped).
INT portTxCongestState	1.3.6.1.4.1.177.3.3.2.1.7	INTEGER	read-only	The congestion state of the port's transmitter. The valid values are notCongested (normal operation), approachingCongestion (FECN and BECN are being set), congested (DE frames are being dropped), and fullyCongested (normal data frames are being dropped).
INT portAccessRate	1.3.6.1.4.1.177.3.3.2.1.8	INTEGER	read-only	The access rate (speed) for this port in bits per second.
INT portCIR	1.3.6.1.4.1.177.3.3.2.1.9	INTEGER	read-only	The total allocated committed information rate for all virtual circuits on this port.
STR portNeighbor	1.3.6.1.4.1.177.3.3.2.1.10	DisplayString	read-only	Represents the IDNX domain-node-card of the adjacent FRX. This field is valid for ports with the interface protocol set to interNode.
CTR portInFrames	1.3.6.1.4.1.177.3.3.2.1.11	Counter	read-only	The number of frames received by this port.
CTR portOutFrames	1.3.6.1.4.1.177.3.3.2.1.12	Counter	read-only	The number of frames transmitter by this port.
CTR portInBytes	1.3.6.1.4.1.177.3.3.2.1.13	Counter	read-only	The number of bytes received by this port.
CTR portOutBytes	1.3.6.1.4.1.177.3.3.2.1.14	Counter	read-only	The number of bytes transmitted by this port.
CTR portDroppedFrames	1.3.6.1.4.1.177.3.3.2.1.15	Counter	read-only	The number of frames dropped by the port for reasons other than: DE, unknown DLCI, bandwidth admission, input/output congestion, frame error, inactive PVC, or disabled port. These are generally internal errors, such as 'Heap buffer failed'.
CTR portDroppedDEFrames	1.3.6.1.4.1.177.3.3.2.1.16	Counter	read-only	The number of frames with DE set dropped due to congestion.
CTR portUnknownDLCIFrames	1.3.6.1.4.1.177.3.3.2.1.17	Counter	read-only	The number of frames received with unknown DLCIs.
INT portLastUnknownDLCI	1.3.6.1.4.1.177.3.3.2.1.18	INTEGER	read-only	The DLCI number of the last frame with an unknown DLCI. A value of -1 signifies that no unknown DLCI has yet been received.
CTR portDEInFrames	1.3.6.1.4.1.177.3.3.2.1.19	Counter	read-only	The number of DE frames received by a port.
CTR portDEOutFrames	1.3.6.1.4.1.177.3.3.2.1.20	Counter	read-only	The number of DE frames transmitted by a port.
CTR portDEInBytes	1.3.6.1.4.1.177.3.3.2.1.21	Counter	read-only	The number of bytes received in DE frames.
CTR portDEOutBytes	1.3.6.1.4.1.177.3.3.2.1.22	Counter	read-only	The number of bytes transmitted in DE frames.
CTR portBECNInFrames	1.3.6.1.4.1.177.3.3.2.1.23	Counter	read-only	The number of BECN frames received by a port.
CTR portBECNOutFrames	1.3.6.1.4.1.177.3.3.2.1.24	Counter	read-only	The number BECN frames transmitted by a port.
CTR portFECNInFrames	1.3.6.1.4.1.177.3.3.2.1.25	Counter	read-only	The number of FECN frames received by a port.
CTR portFECNOutFrames	1.3.6.1.4.1.177.3.3.2.1.26	Counter	read-only	The number of FECN frames transmitted by a port.
GAU portFrameRateIn	1.3.6.1.4.1.177.3.3.2.1.27	Gauge	read-only	The rate in frames per second of frames received by the FRX. This number is a updated every minute and represents the last five minutes worth of traffic.
GAU portFrameRateOut	1.3.6.1.4.1.177.3.3.2.1.28	Gauge	read-only	The rate in frames per second of frames transmitted by the FRX. This number is a updated every minute and represents the last five minutes worth of traffic.
GAU portByteRateIn	1.3.6.1.4.1.177.3.3.2.1.29	Gauge	read-only	The rate in bytes per second received by the FRX. This number is updated every minute and represents the last five minutes worth of traffic.
GAU portByteRateOut	1.3.6.1.4.1.177.3.3.2.1.30	Gauge	read-only	The rate in bytes per second received by the FRX. This number is updated every minute and represents the last five minutes worth of traffic.
GAU portAverageRxQueue	1.3.6.1.4.1.177.3.3.2.1.31	Gauge	read-only	The average depth of the receiver's input queue.
GAU portAverageTxQueue	1.3.6.1.4.1.177.3.3.2.1.32	Gauge	read-only	The average depth of the transmitter's output queue.
GAU portMaxFrameRateIn	1.3.6.1.4.1.177.3.3.2.1.33	Gauge	read-only	The maximum frame rate for frames received by a port.
GAU portMaxFrameRateOut	1.3.6.1.4.1.177.3.3.2.1.34	Gauge	read-only	The maximum frame rate for frames transmitted by a port.
GAU portMaxByteRateIn	1.3.6.1.4.1.177.3.3.2.1.35	Gauge	read-only	The maximum byte rate for frames received by a port.
GAU portMaxByteRateOut	1.3.6.1.4.1.177.3.3.2.1.36	Gauge	read-only	The maximum byte rate for frames transmitted by a port.
GAU portMaxQueueDepthIn	1.3.6.1.4.1.177.3.3.2.1.37	Gauge	read-only	The maximum length of a port's receive queue.
GAU portMaxQueueDepthOut	1.3.6.1.4.1.177.3.3.2.1.38	Gauge	read-only	The maximum length of a port's transmit queue.
CTR portBadFrames	1.3.6.1.4.1.177.3.3.2.1.39	Counter	read-only	The number of frames dropped by the HDLC controller. Examples of reasons why frames are dropped include receiving a bad CRC and non-octet alignment.
CTR portShortFrames	1.3.6.1.4.1.177.3.3.2.1.40	Counter	read-only	The number of frames received by the HDLC controller that don't meet the minimum length restriction.
CTR portMissedFrames	1.3.6.1.4.1.177.3.3.2.1.41	Counter	read-only	The number of receive frames missed by the HDLC controller. This happens when the receiver's input queue is full.
CTR portLongFrames	1.3.6.1.4.1.177.3.3.2.1.42	Counter	read-only	The number of frames received longer than the maximum length.
CTR portRxOverruns	1.3.6.1.4.1.177.3.3.2.1.43	Counter	read-only	The number of receiver overruns the HDLC controller experiences.
CTR portTxUnderruns	1.3.6.1.4.1.177.3.3.2.1.44	Counter	read-only	The number of transmitter underruns the HDLC controller experiences.
INT portStatusEntryId	1.3.6.1.4.1.177.3.3.2.1.45	INTEGER	read-only	The port identifier (number) for this port.
STR portStatsClearedTime	1.3.6.1.4.1.177.3.3.2.1.46	DisplayString	read-only	The amount of time since the last time the statistics were cleared for this port.
CTR portDropBWadmitFrames	1.3.6.1.4.1.177.3.3.2.1.47	Counter	read-only	The number of frames dropped due to Bandwidth Admission enforcement at the port. This occurs when the number of frames is greater than (Bc + Be) during Tc over all Tc's since the last clear of statistics. In other words, these are the burst frames which exceed the sum of the Committed Burst size (Bc) and the Excess Burst size (Be) over each time interval (Tc). This count is only valid when Bandwidth Admission is Enabled for the port; otherwise, it is zero.
CTR portDropInCongestFrames	1.3.6.1.4.1.177.3.3.2.1.48	Counter	read-only	The number of frames dropped because the port input buffer is fully congested.
CTR portDropOutCongestFrames	1.3.6.1.4.1.177.3.3.2.1.49	Counter	read-only	The number of frames dropped because the port output buffer is fully congested.
CTR portDropErroredFrames	1.3.6.1.4.1.177.3.3.2.1.50	Counter	read-only	The number of frames dropped because of frame errors. These include: bad DLCI, invalid DLCI (with and without Cache), invalid source route frame, and wierd frame.
CTR portDropPVCinactiveFrames	1.3.6.1.4.1.177.3.3.2.1.51	Counter	read-only	The number of frames dropped because the PVC is inactive.
CTR portDropPortDisabledFrames	1.3.6.1.4.1.177.3.3.2.1.52	Counter	read-only	The number of frames dropped because the port is Disabled.
INT portChannelAssignment	1.3.6.1.4.1.177.3.3.2.1.53	INTEGER	read-only	This variable will not be available from version 3.0 onwards; it has been replaced by portChannelAssignment30 (see below).
GAU portAlarmedPVCs	1.3.6.1.4.1.177.3.3.2.1.54	Gauge	read-only	The number of circuits on this port where all of the following conditions are true: - circuitState is not 'idle' - circuitStatus is not 'active'.
OCT portChannelAssignment30	1.3.6.1.4.1.177.3.3.2.1.55	OCTET STRING	read-only	The DS0s assigned to this logical backcard port. These may, or may not, be contiguous (when more than one is assigned).
portSdlcEncapMapTable	1.3.6.1.4.1.177.3.3.3		not-accessible	The table containing address map translations between DLCIs and SDLC/HDLC addresses. This table is applicable if the portInterfaceProtocol is sdlcHdlcEncap and the portSdlcEncapMode is addressMapped.
portSdlcEncapMapEntry	1.3.6.1.4.1.177.3.3.3.1		not-accessible	A row from the address map translation table.
INT addressMapSdlcAddress	1.3.6.1.4.1.177.3.3.3.1.1	INTEGER	read-write	The SDLC or HDLC address that is mapped to a DLCI when using SDLC/HDLC encapsulation.
INT addressMapDlci	1.3.6.1.4.1.177.3.3.3.1.2	INTEGER	read-write	The DLCI used when mapping an SCLC/HDLC address when SLDC/HDLC encapsulation is being used.
INT addressMapRowStatus	1.3.6.1.4.1.177.3.3.3.1.3	INTEGER	read-write	Used to create a row in the table.
INT addressMapPortNumber	1.3.6.1.4.1.177.3.3.3.1.4	INTEGER	read-only	The port number index for the address map table.
circuit	1.3.6.1.4.1.177.3.4
circuitConfTable	1.3.6.1.4.1.177.3.4.1		not-accessible	A table containing configuration information for a circuit. The objects in this table are always readable; they can only be written (if accessible) only for the instance in which the circuitConfPortNumber and circuitConfDLCI correspond to the port number and DLCI at the source (originate). When creating a new circuit, at a minimum the destination address must be supplied. Note: Before modifying any circuit configuration variables, the circuit must be disabled (set circuitConfState = 'disable').
circuitConfEntry	1.3.6.1.4.1.177.3.4.1.1		not-accessible	Configuration information about a particular circuit.
STR circuitSourceAddress	1.3.6.1.4.1.177.3.4.1.1.1	DisplayString	read-only	The value of this object is the source (originate) address of this circuit. It is expressed in terms of IDNX Node, Card, and Port (NxCyPz).
INT circuitSourceDLCI	1.3.6.1.4.1.177.3.4.1.1.2	INTEGER	read-write	The value of this object is the DLCI associated with the source address of this circuit.
STR circuitDestinationAddress	1.3.6.1.4.1.177.3.4.1.1.3	DisplayString	read-write	The value of this object is the destination (termination) address of this circuit. The value must be consistent with the endpoint of the user-selected path (if one exists). In the case of a manager that can issue only single-varbind Set requests, clear the user-selected path (if one exists) before attempting to change this value.
INT circuitDestinationDLCI	1.3.6.1.4.1.177.3.4.1.1.4	INTEGER	read-write	The value of this object is the DLCI associated with the destination address of this circuit.
STR circuitUserSelectedPath	1.3.6.1.4.1.177.3.4.1.1.5	DisplayString	read-write	The value of this object is the required path through the FRX network that this virtual circuit must take. The endpoints of this path must be consistent with the configured source and destination addresses. The value 'disabled' indicates that a user-selected path has not been configured.
INT circuitAllowAlternatePath	1.3.6.1.4.1.177.3.4.1.1.6	INTEGER	read-write	If a user-selected path has been configured, enabling this variable allows the FRX to choose an alternate route through the network if the user-selected path is unavailable. Disabling it forces the FRX to wait until the user-selected path is available before establishing the PVC.
INT circuitBandwidthAdmission	1.3.6.1.4.1.177.3.4.1.1.7	INTEGER	read-write	The field reflects the status of bandwidth admission for this virtual circuit. If enabled then CIR, Be, and Bc must be configured.
INT circuitCommittedInfoRate	1.3.6.1.4.1.177.3.4.1.1.8	INTEGER	read-write	The committed information rate (in bits per second) for this virtual circuit.
INT circuitBurstSize	1.3.6.1.4.1.177.3.4.1.1.9	INTEGER	read-write	The burst size (Bc, expressed in bits) for this virtual circuit.
INT circuitExcessBurstSize	1.3.6.1.4.1.177.3.4.1.1.10	INTEGER	read-write	The excess burst size (Be, expressed in bits) for this virtual circuit.
INT circuitPriority	1.3.6.1.4.1.177.3.4.1.1.11	INTEGER	read-write	The priority value of this circuit. If prioritized circuits are not enabled on the port then the circuit priority is set to (normal); normal priority is always one less than the highest priority available, which depend on the number of priority queues defined. There can between 2, and 15 priority queues defined. The default is 3. This parameter can not be set unless Prioritize PVC is enabled for the port (portPriorityQueueing).
INT circuitConfState	1.3.6.1.4.1.177.3.4.1.1.12	INTEGER	read-write	The database state for this virtual circuit. Setting this field to delete causes the virtual circuit to be deleted. Setting this field to install either creates a new circuit, or disables an already existing circuit. Activating the circuit builds the circuit across the network. Note: The database state must be set to 'disable' before any other circuit parameters can be modified.
INT circuitConfPortNumber	1.3.6.1.4.1.177.3.4.1.1.13	INTEGER	read-only	The first index into the circuit configuration table.
INT circuitConfDLCI	1.3.6.1.4.1.177.3.4.1.1.14	INTEGER	read-only	The second index into the circuit configuration table.
circuitStatusTable	1.3.6.1.4.1.177.3.4.2		not-accessible	A table containing virtual circuit status for this port
circuitStatusEntry	1.3.6.1.4.1.177.3.4.2.1		not-accessible	A status entry contains information about virtual circuits.
INT circuitDataBaseState	1.3.6.1.4.1.177.3.4.2.1.1	INTEGER	read-only	The value of this object identifies the current database state of the PVC.
INT circuitState	1.3.6.1.4.1.177.3.4.2.1.2	INTEGER	read-only	This field represents the status of the virtual circuit. The possible values for the state are idle, setup, complete, and disconnect.
STR circuitSetupFailureReason	1.3.6.1.4.1.177.3.4.2.1.3	DisplayString	read-only	This field is valid when the call cannot be completed. The reason the circuit setup failed is contained in this string.
STR circuitLastDisconnectReason	1.3.6.1.4.1.177.3.4.2.1.4	DisplayString	read-only	This field displays the reason for the last disconnect of this virtual circuit, including normal termination.
STR circuitRoute	1.3.6.1.4.1.177.3.4.2.1.5	DisplayString	read-only	This field displays the route that the circuit has taken through the FRX network. It is expressed in terms of IDNX Nodes and Cards (NxCy-NxCy-[...]NxCy.)
INT circuitWindowLength	1.3.6.1.4.1.177.3.4.2.1.6	INTEGER	read-only	The value of this object is the window length (Tc) used for bandwidth admission procedures. The units are tenths-of-seconds. This object is applicable only if bandwidth admission is enabled for the circuit.
CTR circuitReceiveFrames	1.3.6.1.4.1.177.3.4.2.1.7	Counter	read-only	The number of frames received by this circuit.
CTR circuitTransmitFrames	1.3.6.1.4.1.177.3.4.2.1.8	Counter	read-only	The number of frames transmitted by this circuit.
CTR circuitReceiveBytes	1.3.6.1.4.1.177.3.4.2.1.9	Counter	read-only	The number of bytes received by this circuit.
CTR circuitTransmitBytes	1.3.6.1.4.1.177.3.4.2.1.10	Counter	read-only	The number of bytes transmitted by this circuit.
CTR circuitDroppedFrames	1.3.6.1.4.1.177.3.4.2.1.11	Counter	read-only	This field represents the number of frames dropped for this DLCI due to bandwidth admission procedures.
CTR circuitMarkedDEFrames	1.3.6.1.4.1.177.3.4.2.1.12	Counter	read-only	This field represents the number of frames in which the FRX set the DE bit, due to bandwidth admission procedures.
CTR circuitReceivedDEFrames	1.3.6.1.4.1.177.3.4.2.1.13	Counter	read-only	This field represents the number of frames received with the DE bit set.
CTR circuitCurrentTcBurstBits	1.3.6.1.4.1.177.3.4.2.1.14	Counter	read-only	The number of Bc bits received during the present Tc window.
CTR circuitCurrentTcExcessBits	1.3.6.1.4.1.177.3.4.2.1.15	Counter	read-only	The number of Be bits received during the present Tc window.
CTR circuitMaximumBcBits	1.3.6.1.4.1.177.3.4.2.1.16	Counter	read-only	The maximum number of Bc bits received for this virtual circuit.
CTR circuitMaximumBeBits	1.3.6.1.4.1.177.3.4.2.1.17	Counter	read-only	The maximum number of Be bits received for this virtual circuit.
GAU circuitAverageBc	1.3.6.1.4.1.177.3.4.2.1.18	Gauge	read-only	The average number of Bc bits during the past five (5) Tc periods.
GAU circuitAverageBe	1.3.6.1.4.1.177.3.4.2.1.19	Gauge	read-only	The average number of Be bits during the past five (5) Tc periods.
INT circuitStatus	1.3.6.1.4.1.177.3.4.2.1.20	INTEGER	read-only	The status of virtual circuit. The valid values are Active or Inactive.
STR circuitDownReason	1.3.6.1.4.1.177.3.4.2.1.21	DisplayString	read-only	This field is a description of why the virtual circuit is down.
CTR circuitBECNReceiveFrames	1.3.6.1.4.1.177.3.4.2.1.22	Counter	read-only	The number of BECN frames received by the circuit.
CTR circuitBECNTransmitFrames	1.3.6.1.4.1.177.3.4.2.1.23	Counter	read-only	The number of BECN frames transmitted by the circuit.
CTR circuitFECNReceiveFrames	1.3.6.1.4.1.177.3.4.2.1.24	Counter	read-only	The number of FECN frames received by the circuit.
CTR circuitFECNTransmitFrames	1.3.6.1.4.1.177.3.4.2.1.25	Counter	read-only	The number of FECN frames transmitted by the circuit.
INT circuitStatusPortNumber	1.3.6.1.4.1.177.3.4.2.1.26	INTEGER	read-only	The first index into the circuit table.
INT circuitStatusDLCI	1.3.6.1.4.1.177.3.4.2.1.27	INTEGER	read-only	The second index into the circuit table.
INT circuitSrcSidePort	1.3.6.1.4.1.177.3.4.2.1.28	INTEGER	read-only	A circuit segment within an FRX node has two endpoints, each identified by a (port,DLCI) pair. This variable is the source side port number. Note: A value of -1 means 'not applicable'. This variable is not applicable unless the PVC state is Complete.
INT circuitSrcSideDLCI	1.3.6.1.4.1.177.3.4.2.1.29	INTEGER	read-only	A circuit segment within an FRX node has two endpoints, each identified by a (port,DLCI) pair. This variable is the source side DLCI. Note: A value of -1 means 'not applicable'. This variable is not applicable unless the PVC state is Complete.
INT circuitDestSidePort	1.3.6.1.4.1.177.3.4.2.1.30	INTEGER	read-only	A circuit segment within an FRX node has two endpoints, each identified by a (port,DLCI) pair. This variable is the destination side port number. Note: A value of -1 means 'not applicable'. This variable is not applicable unless the PVC state is Complete.
INT circuitDestSideDLCI	1.3.6.1.4.1.177.3.4.2.1.31	INTEGER	read-only	A circuit segment within an FRX node has two endpoints, each identified by a (port,DLCI) pair. This variable is the destination side DLCI. Note: A value of -1 means 'not applicable'. This variable is not applicable unless the PVC state is Complete.
operator	1.3.6.1.4.1.177.3.5
INT operatorCount	1.3.6.1.4.1.177.3.5.1	INTEGER	read-only	The number of operators currently installed on this FRX.
operatorTable	1.3.6.1.4.1.177.3.5.2		not-accessible	The list of operators installed on this FRX. A row can be added to this table using a set request that includes, at minimum, a valid value for operatorIdentifier. A row can be deleted by setting operatorRowStatus to invalid.
operatorTableEntry	1.3.6.1.4.1.177.3.5.2.1		not-accessible	An entry (conceptual row) in the operator table.
INT operatorIndex	1.3.6.1.4.1.177.3.5.2.1.1	INTEGER	read-only	The auxiliary variable used for identifying instances of the columnar objects in the operator table.
STR operatorIdentifier	1.3.6.1.4.1.177.3.5.2.1.2	DisplayString	read-write	A textual string giving the name of this operator. Cannot be empty. A name for a new operator cannot duplicate a name for an existing operator. There is no default value, so a valid value for this column must be includedin any set request for row creation.
INT operatorPrivilege	1.3.6.1.4.1.177.3.5.2.1.3	INTEGER	read-write	The privilege level for this operator.
STR operatorPassword	1.3.6.1.4.1.177.3.5.2.1.4	DisplayString	read-write	The password for this operator. Can be empty.
INT operatorRowStatus	1.3.6.1.4.1.177.3.5.2.1.5	INTEGER	read-write	Setting this column to invalid will delete this operator. Setting it to valid has no effect.
event	1.3.6.1.4.1.177.3.6
eventTypeTable	1.3.6.1.4.1.177.3.6.1		not-accessible	A table listing the types of real-time events on the FRX. The event types comprise two main categories: configuration changes (PVC installed, port activated, etc.), and status changes (port congested, node decongested, etc.). Though the types of events are static, some of their attributes, such as whether or not they trigger an SNMP trap, are configurable.
eventTypeEntry	1.3.6.1.4.1.177.3.6.1.1		not-accessible	Information about a particular event on the FRX. The event types comprise two main categories: configuration changes (PVC installed, port activated, etc.), and status changes (port congested, node decongested, etc.). Though the types of events are static, some of their attributes, such as whether or not they trigger an SNMP trap, are configurable.
INT eventTypeIndex	1.3.6.1.4.1.177.3.6.1.1.1	INTEGER	read-only	Auxiliary variable used to identify row instances in the eventTypeTable.
INT eventTypeLevel	1.3.6.1.4.1.177.3.6.1.1.2	INTEGER	read-write	The IDNX alarm level of this FRX event; user configurable.
INT eventTypeDefaultLevel	1.3.6.1.4.1.177.3.6.1.1.3	INTEGER	read-only	The default IDNX alarm level of this FRX event.
INT eventTypeNetworkSignificant	1.3.6.1.4.1.177.3.6.1.1.4	INTEGER	read-write	Determines whether or not this type of event is forwarded to the repository node for network-significant events.
INT eventTypeDefaultNetworkSignificant	1.3.6.1.4.1.177.3.6.1.1.5	INTEGER	read-only	Default determination of whether or not this type of event is forwarded to the repository node for network-significant events.
INT eventTypeForward	1.3.6.1.4.1.177.3.6.1.1.6	INTEGER	read-write	Determines whether or not this type of event is forwarded to the IDNX event log; user configurable.
INT eventTypeDefaultForward	1.3.6.1.4.1.177.3.6.1.1.7	INTEGER	read-only	Default determination of whether or not this type of event is forwarded to the IDNX event log.
INT eventTypeLog	1.3.6.1.4.1.177.3.6.1.1.8	INTEGER	read-write	Determines whether or not this type of event is logged to the FRX (local) event log; user configurable.
INT eventTypeDefaultLog	1.3.6.1.4.1.177.3.6.1.1.9	INTEGER	read-only	Default determination of whether or not this type of event is logged to the FRX (local) event log.
INT eventTypeTrap	1.3.6.1.4.1.177.3.6.1.1.10	INTEGER	read-write	Determines whether or not this type of event generates an SNMP trap; user configurable.
INT eventTypeDefaultTrap	1.3.6.1.4.1.177.3.6.1.1.11	INTEGER	read-only	Default determination of whether or not this type of event generates an SNMP trap.
INT eventTypeTrapNumber	1.3.6.1.4.1.177.3.6.1.1.12	INTEGER	read-only	Enterprise-specific trap number associated with this event.
network	1.3.6.1.4.1.177.3.7
INT networkNodeCount	1.3.6.1.4.1.177.3.7.1	INTEGER	read-only	The number of nodes this FRX knows about in the FRX network.
networkTable	1.3.6.1.4.1.177.3.7.2		not-accessible	The network table contains information on FRX nodes that is known network wide. This information is distributed via a link state algorithm.
networkTableEntry	1.3.6.1.4.1.177.3.7.2.1		not-accessible	A row in the network table. Each row contains information on a different node in the network.
OCT networkNodeId	1.3.6.1.4.1.177.3.7.2.1.1	OCTET STRING	read-only	The IDNX domain-node-card address of the FRX node.
INT networkTableIndex	1.3.6.1.4.1.177.3.7.2.1.2	INTEGER	read-only	The index for a particular row in the network table. The value of this index is the FRX node number that corresponds to the networkNodeId address.
IP networkNodeIpAddress	1.3.6.1.4.1.177.3.7.2.1.3	IpAddress	read-only	The IP address of the FRX node.
IP networkNodeNetMask	1.3.6.1.4.1.177.3.7.2.1.4	IpAddress	read-only	The network mask of the FRX node.
networkLinkStateTable	1.3.6.1.4.1.177.3.7.3		not-accessible	The link state table is a list of FRX nodes that are neighbors to a given FRX node.
networkLinkStateEntry	1.3.6.1.4.1.177.3.7.3.1		not-accessible	A row in the link state table. Each row contains information on the neighbor nodes for the FRX node in the network table.
OCT linkStateNeighborId	1.3.6.1.4.1.177.3.7.3.1.1	OCTET STRING	read-only	The IDNX domain-node-card address of a neighbor FRX node.
INT linkStateNodeNumber	1.3.6.1.4.1.177.3.7.3.1.2	INTEGER	read-only	The first index into the link state table. The value of this index is an FRX node number.
INT linkStateIndex	1.3.6.1.4.1.177.3.7.3.1.3	INTEGER	read-only	The second index into the link state table.
management	1.3.6.1.4.1.177.3.8
bufferCongestion	1.3.6.1.4.1.177.3.8.1
INT bufferMinimumThreshold	1.3.6.1.4.1.177.3.8.1.1	INTEGER	read-write	The minimum percentage of buffer utilization to cause node congestion.
INT bufferDEFrameThreshold	1.3.6.1.4.1.177.3.8.1.2	INTEGER	read-write	The minimum percentage of buffer utilization that causes DE frames to be dropped.
INT bufferNormalFrameThreshold	1.3.6.1.4.1.177.3.8.1.3	INTEGER	read-write	The minimum percentage of buffer utilization that causes normal data frames to be dropped.
portCongestion	1.3.6.1.4.1.177.3.8.2
portCongestionTable	1.3.6.1.4.1.177.3.8.2.1		not-accessible	A list of the port congestion parameters, row for each port.
portCongestionEntry	1.3.6.1.4.1.177.3.8.2.1.1		not-accessible	A row from the port congestion parameters table.
INT portCongId	1.3.6.1.4.1.177.3.8.2.1.1.1	INTEGER	read-only	The port number associated with this row in the table.
INT portCongFrameDropRate	1.3.6.1.4.1.177.3.8.2.1.1.2	INTEGER	read-write	The rate at which normal frames are dropped during extreme congestion.
INT portCongUtilThreshold	1.3.6.1.4.1.177.3.8.2.1.1.3	INTEGER	read-write	The percentage of the port's access rate, at which time congestion avoidance procedures are started.
INT portCongMinThreshold	1.3.6.1.4.1.177.3.8.2.1.1.4	INTEGER	read-write	The number of seconds of port congestion before FECN and BECN begin to get set.
INT portCongDEThreshold	1.3.6.1.4.1.177.3.8.2.1.1.5	INTEGER	read-write	The number of seconds of APPROACHINGCONGESTION before DE frames begin to get dropped.
INT portCongNormalThreshold	1.3.6.1.4.1.177.3.8.2.1.1.6	INTEGER	read-write	The number of seconds of DECONGESTION before normal data frames begin to get dropped.
routingParameters	1.3.6.1.4.1.177.3.8.3
INT routingLongTimeout	1.3.6.1.4.1.177.3.8.3.1	INTEGER	read-write	The amount of time between normal routing table updates for this FRX node.
INT routingShortTimeout	1.3.6.1.4.1.177.3.8.3.2	INTEGER	read-write	The amount of time to wait after a PVC has been added or deleted before distributing a new routing table update for this FRX node.
INT routingCriticalStaleness	1.3.6.1.4.1.177.3.8.3.3	INTEGER	read-write	The number of minor changes or short timeouts that causes a routing table update to be distributed.
clearObjects	1.3.6.1.4.1.177.3.8.4
clearEventLog	1.3.6.1.4.1.177.3.8.4.1
INT eventLogClear	1.3.6.1.4.1.177.3.8.4.1.1	INTEGER	read-write	Writing to this object will cause the event log to be cleared.
clearPVCStats	1.3.6.1.4.1.177.3.8.4.2
clearPVCStatsTable	1.3.6.1.4.1.177.3.8.4.2.1		not-accessible	A virtual table which is used to clear PVC statistics.
clearPVCStatsEntry	1.3.6.1.4.1.177.3.8.4.2.1.1		not-accessible	A row of parameters which are used to clear PVC based statistics.
INT clearPVCStatsPortId	1.3.6.1.4.1.177.3.8.4.2.1.1.1	INTEGER	read-only	The port number identifying a PVC whose statistics are to be cleared.
INT clearPVCStatsPvcId	1.3.6.1.4.1.177.3.8.4.2.1.1.2	INTEGER	read-only	The DLCI value identifying a PVC whose statistics are to be cleared.
INT clearPVCStatsActivator	1.3.6.1.4.1.177.3.8.4.2.1.1.3	INTEGER	read-write	After setting up the clearPVCStatsPVCId and clearPVCStatsPortId fields, writing to this field will clear the identified PVCs counters.
clearPortStats	1.3.6.1.4.1.177.3.8.4.3
clearPortStatsTable	1.3.6.1.4.1.177.3.8.4.3.1		not-accessible	A virtual table for clearing port based statistics.
clearPortStatsEntry	1.3.6.1.4.1.177.3.8.4.3.1.1		not-accessible	A virtual entry used to clear port statistics.
INT clearPortStatsPortId	1.3.6.1.4.1.177.3.8.4.3.1.1.1	INTEGER	read-write	Setting the field to a valid port number and then writing to clearPortStatsActivator will clear a port's statistics.
INT clearPortStatsActivator	1.3.6.1.4.1.177.3.8.4.3.1.1.2	INTEGER	read-write	After setting the clearPortStatsPortId field with a valid port number, writing to this field will clear a port's statistics.
clearConfiguration	1.3.6.1.4.1.177.3.8.4.4
INT configurationClear	1.3.6.1.4.1.177.3.8.4.4.1	INTEGER	read-write	Writing anything to this field will clear a FRX node's configuration. This can be very dangerous.
saveConfiguration	1.3.6.1.4.1.177.3.8.5
INT configurationSave	1.3.6.1.4.1.177.3.8.5.1	INTEGER	read-write	Writing anything to this field will cause the current configuration to be saved in the non-volatile store of the PX card.
nmsDownloads	1.3.6.1.4.1.177.3.8.6
INT fullConfigDownload	1.3.6.1.4.1.177.3.8.6.1	INTEGER	read-write	Writing anything to this field will cause the current PVC configuration to be downloaded to a NMS workstation.
portQueueThreshold	1.3.6.1.4.1.177.3.8.7
txQueueMaxTable	1.3.6.1.4.1.177.3.8.7.1		not-accessible	A list of the port transmit queue maximum size, row for each port.
txQueueMaxEntry	1.3.6.1.4.1.177.3.8.7.1.1		not-accessible	A row from the port transmit queue max size table.
INT txQueueMaxPortId	1.3.6.1.4.1.177.3.8.7.1.1.1	INTEGER	read-only	The port number associated with this row in the table.
INT txQueueMax	1.3.6.1.4.1.177.3.8.7.1.1.2	INTEGER	read-write	The Transmit Queue Max size for this port.
INT txQueueMaxRangeMin	1.3.6.1.4.1.177.3.8.7.1.1.3	INTEGER	read-only	Transmit Queue Max size range minimum value for this port.
INT txQueueMaxRangeMax	1.3.6.1.4.1.177.3.8.7.1.1.4	INTEGER	read-only	Transmit Queue Max size range maximum value for this port.
priorityQueuesThresholdTable	1.3.6.1.4.1.177.3.8.7.2		not-accessible	A list of the port priority queues threshold, row for each port.
priorityQueuesThresholdEntry	1.3.6.1.4.1.177.3.8.7.2.1		not-accessible	A row from the port priority queues threshold table.
INT thresholdQueuePortId	1.3.6.1.4.1.177.3.8.7.2.1.1	INTEGER	read-only	The port number associated with this row in the table.
INT thresholdQueueId	1.3.6.1.4.1.177.3.8.7.2.1.2	INTEGER	read-only	The queue associated with this row in the table.
INT priorityQueuesThreshold	1.3.6.1.4.1.177.3.8.7.2.1.3	INTEGER	read-write	Priority Queue threshold for this port.
INT priorityQueuesThresholdMin	1.3.6.1.4.1.177.3.8.7.2.1.4	INTEGER	read-only	Minimum Priority Queue threshold for this port.
INT priorityQueuesThresholdMax	1.3.6.1.4.1.177.3.8.7.2.1.5	INTEGER	read-only	Maximum Priority Queue threshold for this port.
priorityQueues	1.3.6.1.4.1.177.3.8.8
INT numberOfPriorities	1.3.6.1.4.1.177.3.8.8.1	INTEGER	read-only	The number of priorities for a given node.
priorityQueueRatioTable	1.3.6.1.4.1.177.3.8.8.2		not-accessible	A list of the port priority queues ratios, row for each port.
priorityQueueRatioEntry	1.3.6.1.4.1.177.3.8.8.2.1		not-accessible	A row from the port priority queues ratio table.
INT priorityQueuePortId	1.3.6.1.4.1.177.3.8.8.2.1.1	INTEGER	read-only	The port number associated with this row in the table.
OCT priorityQueueRatio	1.3.6.1.4.1.177.3.8.8.2.1.2	OCTET STRING	read-write	Priority Queue ratio for this port.
gateway	1.3.6.1.4.1.177.3.9
IP gwIPAddress	1.3.6.1.4.1.177.3.9.1	IpAddress	read-write	The IP Address of the FRX backcard.
IP gwNetMask	1.3.6.1.4.1.177.3.9.2	IpAddress	read-write	The network mask of the FRX backcard.
INT gwRARP	1.3.6.1.4.1.177.3.9.3	INTEGER	read-only	This parameter is not supported. A get on this OID will return disabled. A set on this OID will have no effect.
INT gwRIP	1.3.6.1.4.1.177.3.9.4	INTEGER	read-write	Enable or disable the use of RIP (Routing Information Protocol). With RIP disabled, the user must install static routes on the attached workstation. Default state is disabled.
gwIPAccessTable	1.3.6.1.4.1.177.3.9.5		not-accessible	A table of IP host or network addresses whose managers are allowed to access the FRX gateway.
gwIPAccessEntry	1.3.6.1.4.1.177.3.9.5.1		not-accessible	An IP host or network addresses whose managers are allowed to access the FRX gateway.
INT gwIPAccessRowStatus	1.3.6.1.4.1.177.3.9.5.1.1	INTEGER	read-write	Auxiliary variable used to create or delete row instances in the gateway's IP address access table.
IP gwIPAccessAddress	1.3.6.1.4.1.177.3.9.5.1.2	IpAddress	read-write	The IP address of a host or network that is allowed to access the FRX gateway.
dsx	1.3.6.1.4.1.177.3.10
dsx1ConfigEntry	1.3.6.1.4.1.177.3.10.1
INT dsx1Initialized	1.3.6.1.4.1.177.3.10.1.1	INTEGER	not-accessible	Used to pad the wan structure in wan.h; it is not used for SNMP.
INT dsx1TimeElapsed	1.3.6.1.4.1.177.3.10.1.2	INTEGER	read-only	The number of seconds that have elapsed since the beginning of the current error-measurement period.
INT dsx1ValidIntervals	1.3.6.1.4.1.177.3.10.1.3	INTEGER	read-only	The number of previous intervals for which valid data was collected. The value will be 96 unless the interface was brought on-line within the last 24 hours, in which case the value will be the number of complete 15 minute intervals the since interface has been online.
INT dsx1LineType	1.3.6.1.4.1.177.3.10.1.4	INTEGER	read-write	This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: dsx1ESF Extended SuperFrame DS1 dsx1D4 AT&T D4 format DS1 dsx1E1 CCITT Recommendation G.704 (Table 4a) dsx1E1-CRC CCITT Recommendation G.704 (Table 4b) dsxE1-MF G.704 (Table 4a) with TS16 multiframing enabled dsx1E1-CRC-MF G.704 (Table 4b) with TS16 multiframing enabled
INT dsx1LineCoding	1.3.6.1.4.1.177.3.10.1.5	INTEGER	read-write	This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. dsx1B8ZS refers to the use of a specified pat- tern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits. ANSI Clear Channels may use dsx1ZBTSI, or Zero Byte Time Slot Interchange. E1 links, with or without CRC, use dsx1HDB3 or dsx1AMI. dsx1AMI refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density re- quirements, such as inverting HDLC data.
INT dsx1SendCode	1.3.6.1.4.1.177.3.10.1.6	INTEGER	read-write	This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: dsx1SendNoCode sending looped or normal data dsx1SendLineCode sending a request for a line loopback dsx1SendPayloadCode sending a request for a payload loopback dsx1SendResetCode sending a loopback termination request dsx1SendQRS sending a Quasi-Random Signal (QRS) test pattern dsx1Send511Pattern sending a 511 bit fixed test pattern dsx1Send3in24Pattern sending a fixed test pattern of 3 bits set in 24 dsx1SendOtherTestPattern sending a test pattern other than those described by this object
STR dsx1CircuitIdentifier	1.3.6.1.4.1.177.3.10.1.7	DisplayString	read-write	This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting.
INT dsx1LoopbackConfig	1.3.6.1.4.1.177.3.10.1.8	INTEGER	read-write	This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a requested loopback state that the interface does not support. The values mean: dsx1NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value. dsx1PayloadLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for re- transmission after it has passed through the device's framing function. dsx1LineLoop The received signal at this interface does not go through the device (minimum pene- tration) but is looped back out. dsx1OtherLoop Loopbacks that are not defined here.
INT dsx1LineStatus	1.3.6.1.4.1.177.3.10.1.9	INTEGER	read-only	This variable indicates the Line Status of the interface. It contains loopback, failure, re- ceived 'alarm' and transmitted 'alarm' infor- mation. -- The dsx1LineStatus is a bit map represented as a sum, -- therefore, it can represent multiple failures (alarms) and -- a LoopbackState simultaneously. -- dsx1NoAlarm should be set if and only if no other flag is -- set. -- If the dsx1LoopbackState bit is set, the loopback in ef- -- fect can be determined from the dsx1LoopbackConfig object. -- The various bit positions are: -- 1 dsx1NoAlarm No Alarm Present -- 2 dsx1RcvFarEndLOF Far end LOF (a.k.a. Yellow Alarm) -- 4 dsx1XmtFarEndLOF Near end sending LOF Indication -- 8 dsx1RcvAIS Far end sending AIS -- 16 dsx1XmtAIS Near end sending AIS -- 32 dsx1LossOfFrame Near end LOF (a.k.a. Red Alarm) -- 64 dsx1LossOfSignal Near end Loss Of Signal -- 128 dsx1LoopbackState Near end is looped -- 256 dsx1T16AIS E1 TS16 AIS -- 512 dsx1RcvFarEndLOMF Far End Sending TS16 LOMF -- 1024 dsx1XmtFarEndLOMF Near End Sending TS16 LOMF -- 2048 dsx1RcvTestCode Near End detects a test code -- 4096 dsx1OtherFailure any line status not defined here
INT dsx1LineMode	1.3.6.1.4.1.177.3.10.1.10	INTEGER	read-write	This set of values describes the mode of the WAN I/F. For DS1 lines it sets the mode to CSU by way of a standard dB level, and for DSX configurations sets the line buildout in feet. for E1 lines, it sets the mode in Ohm
INT dsx1TransmitClockSource	1.3.6.1.4.1.177.3.10.1.11	INTEGER	read-write	The source of Tranmit Clock. 'loopTiming' indicates that the recovered re- ceive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used. 'throughTiming' indicates that recovered re- ceive clock from another interface is ised as the transmit clock.
INT dsx1Fdl	1.3.6.1.4.1.177.3.10.1.12	INTEGER	read-write	This bitmap describes the use of the facili- ties data link, and is the sum of the capabili- ties: 'other' indicates that a protocol other than one following is used. 'dsx1Ansi-T1-403' refers to the FDL exchange recommended by ANSI. (This is a T1-only option.) 'dsx1Att-54016' refers to ESF FDL exchanges. (This is a T1-only option.) 'dsx1Fdl-none' indicates that the device does not use the FDL.
INT dsx1YellowAlarmStyle	1.3.6.1.4.1.177.3.10.1.13	INTEGER	read-write	This variable describes the use of the yellow alarm style when in D4 line encoding mode.
dsx1CurrentTable	1.3.6.1.4.1.177.3.10.2		not-accessible	The DS1 Current table.
dsx1CurrentEntry	1.3.6.1.4.1.177.3.10.2.1		not-accessible	An entry in the DS1 Current table.
INT dsx1CurrentIndex	1.3.6.1.4.1.177.3.10.2.1.1	INTEGER	read-only	The index value which uniquely identifies the DS1 interface to which this entry is applica- ble. The interface identified by a particular value of this index is the same interface as identified by the same value as a dsx1LineIndex object instance.
GAU dsx1CurrentESs	1.3.6.1.4.1.177.3.10.2.1.2	Gauge	read-only	The number of Errored Seconds, encountered by a DS1 interface in the current 15 minute inter- val.
GAU dsx1CurrentSESs	1.3.6.1.4.1.177.3.10.2.1.3	Gauge	read-only	The number of Severely Errored Seconds encoun- tered by a DS1 interface in the current 15 minute interval.
GAU dsx1CurrentSEFSs	1.3.6.1.4.1.177.3.10.2.1.4	Gauge	read-only	The number of Severely Errored Framing Seconds encountered by a DS1 interface in the current 15 minute interval.
GAU dsx1CurrentUASs	1.3.6.1.4.1.177.3.10.2.1.5	Gauge	read-only	The number of Unavailable Seconds encountered by a DS1 interface in the current 15 minute in- terval.
GAU dsx1CurrentCSSs	1.3.6.1.4.1.177.3.10.2.1.6	Gauge	read-only	The number of Controlled Slip Seconds encoun- tered by a DS1 interface in the current 15 minute interval.
GAU dsx1CurrentPCVs	1.3.6.1.4.1.177.3.10.2.1.7	Gauge	read-only	The number of Path Coding Violations encoun- tered by a DS1 interface in the current 15 minute interval.
GAU dsx1CurrentLESs	1.3.6.1.4.1.177.3.10.2.1.8	Gauge	read-only	The number of Line Errored Seconds encountered by a DS1 interface in the current 15 minute in- terval.
GAU dsx1CurrentBESs	1.3.6.1.4.1.177.3.10.2.1.9	Gauge	read-only	The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the current 15 minute interval.
GAU dsx1CurrentDMs	1.3.6.1.4.1.177.3.10.2.1.10	Gauge	read-only	The number of Degraded Minutes (DMs) encoun- tered by a DS1 interface in the current 15 minute interval.
GAU dsx1CurrentLCVs	1.3.6.1.4.1.177.3.10.2.1.11	Gauge	read-only	The number of Line Code Violations (LCVs) en- countered by a DS1 interface in the current 15 minute interval.
dsx1IntervalTable	1.3.6.1.4.1.177.3.10.3		not-accessible	The DS1 Interval table.
dsx1IntervalEntry	1.3.6.1.4.1.177.3.10.3.1		not-accessible	An entry in the DS1 Interval table.
INT dsx1IntervalIndex	1.3.6.1.4.1.177.3.10.3.1.1	INTEGER	read-only	The index value which uniquely identifies the DS1 interface to which this entry is applica- ble. The interface identified by a particular value of this index is the same interface as identified by the same value as a dsx1LineIndex object instance.
INT dsx1IntervalNumber	1.3.6.1.4.1.177.3.10.3.1.2	INTEGER	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes inter- val (assuming that all 96 intervals are valid).
GAU dsx1IntervalESs	1.3.6.1.4.1.177.3.10.3.1.3	Gauge	read-only	The number of Errored Seconds encountered by a DS1 interface in one of the previous 96, indi- vidual 15 minute, intervals.
GAU dsx1IntervalSESs	1.3.6.1.4.1.177.3.10.3.1.4	Gauge	read-only	The number of Severely Errored Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalSEFSs	1.3.6.1.4.1.177.3.10.3.1.5	Gauge	read-only	The number of Severely Errored Framing Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalUASs	1.3.6.1.4.1.177.3.10.3.1.6	Gauge	read-only	The number of Unavailable Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalCSSs	1.3.6.1.4.1.177.3.10.3.1.7	Gauge	read-only	The number of Controlled Slip Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalPCVs	1.3.6.1.4.1.177.3.10.3.1.8	Gauge	read-only	The number of Path Coding Violations encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalLESs	1.3.6.1.4.1.177.3.10.3.1.9	Gauge	read-only	The number of Line Errored Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalBESs	1.3.6.1.4.1.177.3.10.3.1.10	Gauge	read-only	The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalDMs	1.3.6.1.4.1.177.3.10.3.1.11	Gauge	read-only	The number of Degraded Minutes (DMs) encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1IntervalLCVs	1.3.6.1.4.1.177.3.10.3.1.12	Gauge	read-only	The number of Line Code Violations (LCVs) en- countered by a DS1 interface in the current 15 minute interval.
dsx1TotalTable	1.3.6.1.4.1.177.3.10.4		not-accessible	The DS1 Total table. 24 hour interval.
dsx1TotalEntry	1.3.6.1.4.1.177.3.10.4.1		not-accessible	An entry in the DS1 Total table.
INT dsx1TotalIndex	1.3.6.1.4.1.177.3.10.4.1.1	INTEGER	read-only	The index value which uniquely identifies the DS1 interface to which this entry is applica- ble. The interface identified by a particular value of this index is the same interface as identified by the same value as a dsx1LineIndex object instance.
GAU dsx1TotalESs	1.3.6.1.4.1.177.3.10.4.1.2	Gauge	read-only	The number of Errored Seconds encountered by a DS1 interface in the previous 24 hour interval
GAU dsx1TotalSESs	1.3.6.1.4.1.177.3.10.4.1.3	Gauge	read-only	The number of Severely Errored Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
GAU dsx1TotalSEFSs	1.3.6.1.4.1.177.3.10.4.1.4	Gauge	read-only	The number of Severely Errored Framing Seconds encountered by a DS1 interface in the previous 24 hour interval.
GAU dsx1TotalUASs	1.3.6.1.4.1.177.3.10.4.1.5	Gauge	read-only	The number of Unavailable Seconds encountered by a DS1 interface in the previous 24 hour in- terval.
GAU dsx1TotalCSSs	1.3.6.1.4.1.177.3.10.4.1.6	Gauge	read-only	The number of Controlled Slip Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
GAU dsx1TotalPCVs	1.3.6.1.4.1.177.3.10.4.1.7	Gauge	read-only	The number of Path Coding Violations encoun- tered by a DS1 interface in the previous 24 hour interval.
GAU dsx1TotalLESs	1.3.6.1.4.1.177.3.10.4.1.8	Gauge	read-only	The number of Line Errored Seconds encountered by a DS1 interface in the previous 24 hour in- terval.
GAU dsx1TotalBESs	1.3.6.1.4.1.177.3.10.4.1.9	Gauge	read-only	The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the previous 24 hour interval.
GAU dsx1TotalDMs	1.3.6.1.4.1.177.3.10.4.1.10	Gauge	read-only	The number of Degraded Minutes (DMs) encoun- tered by a DS1 interface in the previous 24 hour interval.
GAU dsx1TotalLCVs	1.3.6.1.4.1.177.3.10.4.1.11	Gauge	read-only	The number of Line Code Violations (LCVs) en- countered by a DS1 interface in the current 15 minute interval.
dsx1FarEndCurrentTable	1.3.6.1.4.1.177.3.10.5		not-accessible	The DS1 Far End Current table.
dsx1FarEndCurrentEntry	1.3.6.1.4.1.177.3.10.5.1		not-accessible	An entry in the DS1 Far End Current table.
INT dsx1FarEndCurrentIndex	1.3.6.1.4.1.177.3.10.5.1.1	INTEGER	read-only	The index value which uniquely identifies the DS1 interface to which this entry is applica- ble. The interface identified by a particular value of this index is the same interface as identified by the same value an dsx1LineIndex object instance.
INT dsx1FarEndTimeElapsed	1.3.6.1.4.1.177.3.10.5.1.2	INTEGER	read-only	The number of seconds that have elapsed since the beginning of the far end current error-measurement period.
INT dsx1FarEndValidIntervals	1.3.6.1.4.1.177.3.10.5.1.3	INTEGER	read-only	The number of previous far end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute far end intervals since the interface has been online.
GAU dsx1FarEndCurrentESs	1.3.6.1.4.1.177.3.10.5.1.4	Gauge	read-only	The number of Far Far End Errored Seconds en- countered by a DS1 interface in the current 15 minute interval.
GAU dsx1FarEndCurrentSESs	1.3.6.1.4.1.177.3.10.5.1.5	Gauge	read-only	The number of Far End Severely Errored Seconds encountered by a DS1 interface in the current 15 minute interval.
GAU dsx1FarEndCurrentSEFSs	1.3.6.1.4.1.177.3.10.5.1.6	Gauge	read-only	The number of Far End Severely Errored Framing Seconds encountered by a DS1 interface in the current 15 minute interval.
GAU dsx1FarEndCurrentUASs	1.3.6.1.4.1.177.3.10.5.1.7	Gauge	read-only	The number of Unavailable Seconds encountered by a DS1 interface in the current 15 minute in- terval.
GAU dsx1FarEndCurrentCSSs	1.3.6.1.4.1.177.3.10.5.1.8	Gauge	read-only	The number of Far End Controlled Slip Seconds encountered by a DS1 interface in the current 15 minute interval.
GAU dsx1FarEndCurrentLESs	1.3.6.1.4.1.177.3.10.5.1.9	Gauge	read-only	The number of Far End Line Errored Seconds en- countered by a DS1 interface in the current 15 minute interval.
GAU dsx1FarEndCurrentPCVs	1.3.6.1.4.1.177.3.10.5.1.10	Gauge	read-only	The number of Far End Path Coding Violations reported via the far end block error count en- countered by a DS1 interface in the current 15 minute interval.
GAU dsx1FarEndCurrentBESs	1.3.6.1.4.1.177.3.10.5.1.11	Gauge	read-only	The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the current 15 minute interval.
GAU dsx1FarEndCurrentDMs	1.3.6.1.4.1.177.3.10.5.1.12	Gauge	read-only	The number of Degraded Minutes (DMs) encoun- tered by a DS1 interface in the current 15 minute interval.
dsx1FarEndIntervalTable	1.3.6.1.4.1.177.3.10.6		not-accessible	The DS1 Far End Interval table.
dsx1FarEndIntervalEntry	1.3.6.1.4.1.177.3.10.6.1		not-accessible	An entry in the DS1 Far End Interval table.
INT dsx1FarEndIntervalIndex	1.3.6.1.4.1.177.3.10.6.1.1	INTEGER	read-only	The index value which uniquely identifies the DS1 interface to which this entry is applica- ble. The interface identified by a particular value of this index is the same interface as identified by the same value as a dsx1LineIndex object instance.
INT dsx1FarEndIntervalNumber	1.3.6.1.4.1.177.3.10.6.1.2	INTEGER	read-only	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes inter- val (assuming that all 96 intervals are valid).
GAU dsx1FarEndIntervalESs	1.3.6.1.4.1.177.3.10.6.1.3	Gauge	read-only	The number of Far End Errored Seconds encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1FarEndIntervalSESs	1.3.6.1.4.1.177.3.10.6.1.4	Gauge	read-only	The number of Far End Severely Errored Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1FarEndIntervalSEFSs	1.3.6.1.4.1.177.3.10.6.1.5	Gauge	read-only	The number of Far End Severely Errored Framing Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, in- tervals.
GAU dsx1FarEndIntervalUASs	1.3.6.1.4.1.177.3.10.6.1.6	Gauge	read-only	The number of Unavailable Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1FarEndIntervalCSSs	1.3.6.1.4.1.177.3.10.6.1.7	Gauge	read-only	The number of Far End Controlled Slip Seconds encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1FarEndIntervalLESs	1.3.6.1.4.1.177.3.10.6.1.8	Gauge	read-only	The number of Far End Line Errored Seconds en- countered by a DS1 interface in one of the pre- vious 96, individual 15 minute, intervals.
GAU dsx1FarEndIntervalPCVs	1.3.6.1.4.1.177.3.10.6.1.9	Gauge	read-only	The number of Far End Path Coding Violations reported via the far end block error count en- countered by a DS1 interface in one of the pre- vious 96, individual 15 minute, intervals.
GAU dsx1FarEndIntervalBESs	1.3.6.1.4.1.177.3.10.6.1.10	Gauge	read-only	The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
GAU dsx1FarEndIntervalDMs	1.3.6.1.4.1.177.3.10.6.1.11	Gauge	read-only	The number of Degraded Minutes (DMs) encoun- tered by a DS1 interface in one of the previous 96, individual 15 minute, intervals.
dsx1FarEndTotalTable	1.3.6.1.4.1.177.3.10.7		not-accessible	The DS1 Far End Total table.
dsx1FarEndTotalEntry	1.3.6.1.4.1.177.3.10.7.1		not-accessible	An entry in the DS1 Far End Total table.
INT dsx1FarEndTotalIndex	1.3.6.1.4.1.177.3.10.7.1.1	INTEGER	read-only	The index value which uniquely identifies the DS1 interface to which this entry is applica- ble. The interface identified by a particular value of this index is the same interface as identified by the same value an dsx1LineIndex object instance.
GAU dsx1FarEndTotalESs	1.3.6.1.4.1.177.3.10.7.1.2	Gauge	read-only	The number of Far End Errored Seconds encoun- tered by a DS1 interface in the previous 24 hour interval.
GAU dsx1FarEndTotalSESs	1.3.6.1.4.1.177.3.10.7.1.3	Gauge	read-only	The number of Far End Severely Errored Seconds encountered by a DS1 interface in the previous 24 hour interval.
GAU dsx1FarEndTotalSEFSs	1.3.6.1.4.1.177.3.10.7.1.4	Gauge	read-only	The number of Far End Severely Errored Framing Seconds encountered by a DS1 interface in the previous 24 hour interval.
GAU dsx1FarEndTotalUASs	1.3.6.1.4.1.177.3.10.7.1.5	Gauge	read-only	The number of Unavailable Seconds encountered by a DS1 interface in the previous 24 hour in- terval.
GAU dsx1FarEndTotalCSSs	1.3.6.1.4.1.177.3.10.7.1.6	Gauge	read-only	The number of Far End Controlled Slip Seconds encountered by a DS1 interface in the previous 24 hour interval.
GAU dsx1FarEndTotalLESs	1.3.6.1.4.1.177.3.10.7.1.7	Gauge	read-only	The number of Far End Line Errored Seconds en- countered by a DS1 interface in the previous 24 hour interval.
GAU dsx1FarEndTotalPCVs	1.3.6.1.4.1.177.3.10.7.1.8	Gauge	read-only	The number of Far End Path Coding Violations reported via the far end block error count en- countered by a DS1 interface in the previous 24 hour interval.
GAU dsx1FarEndTotalBESs	1.3.6.1.4.1.177.3.10.7.1.9	Gauge	read-only	The number of Bursty Errored Seconds (BESs) encountered by a DS1 interface in the previous 24 hour interval.
GAU dsx1FarEndTotalDMs	1.3.6.1.4.1.177.3.10.7.1.10	Gauge	read-only	The number of Degraded Minutes (DMs) encoun- tered by a DS1 interface in the previous 24 hour interval.
dsx1ChanOwnerTable	1.3.6.1.4.1.177.3.10.8		not-accessible	The DS1 Channel-to-Port mapping table.
dsx1ChanOwnerEntry	1.3.6.1.4.1.177.3.10.8.1		not-accessible	An entry in the dsx1ChanOwner table, indexed by channel showing which logical port owns this channel. An entry of -1 depicts a channel that is freely assignable.
INT dsx1ChanIndex	1.3.6.1.4.1.177.3.10.8.1.1	INTEGER	read-only	The index value which uniquely identifies the DSX channel to which this entry is applicable.
INT dsx1ChanOwnerPort	1.3.6.1.4.1.177.3.10.8.1.2	INTEGER	read-write	The number of the port to which this channel is assigned.
dsx1PortModeTable	1.3.6.1.4.1.177.3.10.9		not-accessible	The DS1 Logical Port-to-Mode mapping table.
dsx1PortModeEntry	1.3.6.1.4.1.177.3.10.9.1		not-accessible	An entry in the DS1 Port->Mode table, indexed by port showing which mode this port runs in. An entry of 0 depicts a port that is operating in the DS0 mode, a non-zero entry indicates the 56K mode. Note that a DS1 link operating JBZS will always have all of its channels operating in 56K mode.
INT dsx1PortMode	1.3.6.1.4.1.177.3.10.9.1.1	INTEGER	read-write	The port mode of the T1/E1 Back Card port to which this entry is applicable.
INT dsx1PortIndex	1.3.6.1.4.1.177.3.10.9.1.2	INTEGER	read-only	The index value which uniquely identifies the T1/E1 Back Card port to which this entry is applicable.
filesystem	1.3.6.1.4.1.177.3.11
INT exportFileSystem	1.3.6.1.4.1.177.3.11.1	INTEGER	read-write	Determines whether this node will export its filesystem. The default will be . This variable can be changed by the FrameXpress Node Manager. When the agent receives the request to change this variable to , it attempts to export the file system prior to responding to the Node Manager. If the export fails, the SNMP request will fail sending a failure response to the Manager.
INT loadAndExecute	1.3.6.1.4.1.177.3.11.2	INTEGER	read-write	Triggers the loading of SNMPCNF.CMD if such a file existed, otherwise, it triggers the loading of DEFAULT.CFG after clearing the current configuration.
adaptive	1.3.6.1.4.1.177.4
idnx	1.3.6.1.4.1.177.5

RFC description

Manages Frame Relay Exchange (FRX) devices from NET with port, circuit and T1/E1 backcard monitoring.

Start monitoring Legacy frame relay switch/access node (Netrix/FastComm-style FRX platform) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download FRX-MIB

What Is FRX-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description