FOUNDRY-SN-SWITCH-GROUP-MIB

All MIBs › FOUNDRY-SN-SWITCH-GROUP-MIB

Organization: Brocade Communications Systems, Inc.

Last Updated: 2013-10-25

Category: VLAN and Bridging, Vendor: Foundry/Brocade

Description: Brocade/Foundry proprietary MIB for switch group management covering VLANs, MAC tables, STP, and port configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is FOUNDRY-SN-SWITCH-GROUP-MIB?

FOUNDRY-SN-SWITCH-GROUP-MIB is a Brocade/Foundry proprietary MIB for managing switch-group-level Layer 2/3 features on Foundry (later Brocade) Ethernet switches, covering VLAN configuration, MAC address (forwarding database) tables, spanning tree port state, and switch-wide operating modes. It exposes configuration data such as Layer 3 switching mode, IP multicast mode, default configuration mode, and switch aging time, alongside per-VLAN, per-port, and FDB table entries. It supports monitoring device operational status through objects like snPortStpSetAll (spanning-tree port states) and the FDB table (snFdbTableCurEntry), which reveal port blocking/forwarding state and MAC learning activity, useful for diagnosing loops or connectivity issues. This kind of FOUNDRY-SN-SWITCH-GROUP-MIB SNMP monitoring is commonly paired with the standards-based BRIDGE-MIB to cross-check spanning-tree and forwarding-database state on the same switch. It is a Foundry/Brocade enterprise MIB with no dependency on external standards MIBs beyond basic SNMPv2-SMI conventions, though it parallels functionality found in the standards-based BRIDGE-MIB. It is deployed on Foundry/Brocade enterprise Ethernet switches (e.g. FastIron, BigIron series) in campus and data-center networks.

IPNetwork Monitor allows you to monitor SNMP objects defined in FOUNDRY-SN-SWITCH-GROUP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ruckus (CommScope) ICX 8200 (current) — successor to Foundry/Brocade FastIron switching
Ruckus ICX 7550 (current) — stackable enterprise switch

Monitoring Examples

An administrator checks snSwGroupOperMode and snSwGroupIpL3SwMode to confirm whether the switch group is running in the expected Layer 2 or Layer 3 switching mode after a configuration change. Polling snFdbTableCurEntry reveals current MAC address table entries, and an unexpectedly rapid churn combined with snSwGroupSwitchAgeTime settings can indicate a topology loop; issuing snFdbTableStationFlush clears stale entries. snPortStpSetAll and snVLanGroupVlanCurEntry are polled together to verify a given port's spanning-tree state matches its intended VLAN membership.

What Can Be Monitored

Layer 2/3 switching mode
IP multicast mode
MAC/FDB table entries
switch MAC aging time
spanning-tree port state
VLAN membership per port

Imported Objects

From FOUNDRY-SN-AGENT-MIB

DisplayString
MacAddress

From FOUNDRY-SN-ROOT-MIB

switch

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From P-BRIDGE-MIB

EnabledStatus

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using snSwIfStatsInUtilization OID:

Select a Brocade/Foundry FastIron/BigIron Ethernet switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type snSwIfStatsInUtilization into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the input network utilization on this interface, in hundredths of a percent, averaged over a 5-minute interval. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is an INTEGER-type OID, Value bounds is the most useful condition here — trigger an alert if utilization exceeds 80%, since sustained high inbound utilization often precedes latency and packet loss. Click Finish to create the monitor; you can adjust any parameter later.

See also: snVLanGroupVlanCurEntry

OIDs

OID symbolic	OID numeric	Type	Access	Description
C64 brcdIfEgressCounterDropPkts	1.3.6.1.4.1.1991.1.1.3.3.11.1.5	Counter64	read-only	The egress dropped packet counters of the queue in a given port.
NUM brcdIfEgressCounterIfIndex	1.3.6.1.4.1.1991.1.1.3.3.11.1.1	InterfaceIndex	not-accessible	The port number of egress counter in the physical port. The port/interface index (ifindex).
brcdIfEgressCounterInfoEntry	1.3.6.1.4.1.1991.1.1.3.3.11.1		not-accessible	An entry in the Interface Egress Counter Information table. The ifIndices of ethernet interfaces and the queue number will be used to index this table.
brcdIfEgressCounterInfoTable	1.3.6.1.4.1.1991.1.1.3.3.11		not-accessible	This table lists the information of egress counters of all the queues in the physical ports.
C64 brcdIfEgressCounterPkts	1.3.6.1.4.1.1991.1.1.3.3.11.1.4	Counter64	read-only	The egress packet counters of the queue in a given port.
INT brcdIfEgressCounterQueueId	1.3.6.1.4.1.1991.1.1.3.3.11.1.2	INTEGER	not-accessible	The queue number of egress counter in the given port.
INT brcdIfEgressCounterType	1.3.6.1.4.1.1991.1.1.3.3.11.1.3	INTEGER	read-only	The queue type of the egress counter in a given port.
brcdRouteMap	1.3.6.1.4.1.1991.1.1.3.39
brcdSPXMIB	1.3.6.1.4.1.1991.1.1.3.40
brcdVlanExtStatsEntry	1.3.6.1.4.1.1991.1.1.3.2.8.1		not-accessible	A row in this table represents a VLAN extended statistics accounting entry. It can be a per-VLAN/port entry, in this case the Priority-ID is 128 (invalid). It can also be in a priority level granularity of the VLAN port, in this case the Priority-ID specifies which port QOS priority, and Priority-ID 128 is the index to the aggregate count bucket.
NUM brcdVlanExtStatsIfIndex	1.3.6.1.4.1.1991.1.1.3.2.8.1.2	InterfaceIndex	not-accessible	The ifIndex of the port belonging to this VLAN.
C64 brcdVlanExtStatsInOctets	1.3.6.1.4.1.1991.1.1.3.2.8.1.12	Counter64	read-only	The bytes count received by this port classified as belonging to this VLAN for both switched and routed packets.
C64 brcdVlanExtStatsInPkts	1.3.6.1.4.1.1991.1.1.3.2.8.1.6	Counter64	read-only	The number of valid frames received by this port classified as belonging to this VLAN for both switched and routed packets.
C64 brcdVlanExtStatsInRoutedOctets	1.3.6.1.4.1.1991.1.1.3.2.8.1.11	Counter64	read-only	The bytes count received by this port classified as belonging to this VLAN for routed packets. The value is applicable only if the system was configured to separately count the two types of packets. Otherwise, it returns 0.
C64 brcdVlanExtStatsInRoutedPkts	1.3.6.1.4.1.1991.1.1.3.2.8.1.5	Counter64	read-only	The number of valid frames received by this port classified as belonging to this VLAN for routed packets. The value is applicable only if the system was configured to separately count the two types of packets. Otherwise, it returns 0.
C64 brcdVlanExtStatsInSwitchedOctets	1.3.6.1.4.1.1991.1.1.3.2.8.1.10	Counter64	read-only	The bytes count received by this port classified as belonging to this VLAN for switched packets. The value is applicable only if the system was configured to separately count the two types of packets. Otherwise, it returns 0.
C64 brcdVlanExtStatsInSwitchedPkts	1.3.6.1.4.1.1991.1.1.3.2.8.1.4	Counter64	read-only	The number of valid frames received by this port classified as belonging to this VLAN for switched packets. The value is applicable only if the system was configured to separately count the two types of packets. Otherwise, it returns 0.
C64 brcdVlanExtStatsOutOctets	1.3.6.1.4.1.1991.1.1.3.2.8.1.15	Counter64	read-only	The bytes count transmitted by this port classified as belonging to this VLAN for both switched and routed packets.
C64 brcdVlanExtStatsOutPkts	1.3.6.1.4.1.1991.1.1.3.2.8.1.9	Counter64	read-only	The number of valid frames transmitted by this port classified as belonging to this VLAN for both switched and routed packets.
C64 brcdVlanExtStatsOutRoutedOctets	1.3.6.1.4.1.1991.1.1.3.2.8.1.14	Counter64	read-only	The bytes count transmitted by this port classified as belonging to this VLAN for routed packets. The value is applicable only if the system was configured to separately count the two types of packets. Otherwise, it returns 0.
C64 brcdVlanExtStatsOutRoutedPkts	1.3.6.1.4.1.1991.1.1.3.2.8.1.8	Counter64	read-only	The number of valid frames transmitted by this port classified as belonging to this VLAN for routed packets. The value is applicable only if the system was configured to separately count the two types of packets. Otherwise, it returns 0.
C64 brcdVlanExtStatsOutSwitchedOctets	1.3.6.1.4.1.1991.1.1.3.2.8.1.13	Counter64	read-only	The bytes count transmitted by this port classified as belonging to this VLAN for switched packets. The value is applicable only if the system was configured to separately count the two types of packets. Otherwise, it returns 0.
C64 brcdVlanExtStatsOutSwitchedPkts	1.3.6.1.4.1.1991.1.1.3.2.8.1.7	Counter64	read-only	The number of valid frames transmitted by this port classified as belonging to this VLAN for switched packets. The value is applicable only if the system was configured to separately count the two types of packets. Otherwise, it returns 0.
POR brcdVlanExtStatsPriorityId	1.3.6.1.4.1.1991.1.1.3.2.8.1.3	PortPriorityTC	not-accessible	Identifies the port QOS priority. The values 1 through 8 internally maps to priorities 0 through 7. The value 128 indicates that priority-level accounting is not enabled
brcdVlanExtStatsTable	1.3.6.1.4.1.1991.1.1.3.2.8		not-accessible	This table contains the extended statistics for VLAN ports of G2 and later modules. Not applicable for G1 cards. These applies to L2 VLANs and as well as port VLANs that are associated to IP interfaces (physical or VE).
BRC brcdVlanExtStatsVlanId	1.3.6.1.4.1.1991.1.1.3.2.8.1.1	BrcdVlanIdTC	not-accessible	The VLAN identifier (VLAN ID).
fdryDaiMIB	1.3.6.1.4.1.1991.1.1.3.35
fdryDhcpSnoopMIB	1.3.6.1.4.1.1991.1.1.3.36
fdryDns2MIB	1.3.6.1.4.1.1991.1.1.3.34
fdryIpSrcGuardMIB	1.3.6.1.4.1.1991.1.1.3.37
fdryLinkAggregationGroupMIB	1.3.6.1.4.1.1991.1.1.3.33
fdryMacVlanMIB	1.3.6.1.4.1.1991.1.1.3.32
sn6to4TunnelInterface	1.3.6.1.4.1.1991.1.1.3.3.2.13
snAAA	1.3.6.1.4.1.1991.1.1.3.15
snAccounting	1.3.6.1.4.1.1991.1.1.3.15.3
INT snAccountingCommandLevel	1.3.6.1.4.1.1991.1.1.3.15.3.2	INTEGER	read-write	Commands, which are equal to and less than the specified command level here will be accounted. Possible enumeration values: level0 - Privilege level 0 level4 - Privilege level 4 level5 - Privilege level 5.
OCT snAccountingCommandMethods	1.3.6.1.4.1.1991.1.1.3.15.3.1	OCTET STRING	read-write	A sequence of accounting methods. Each octet represents a method to account for the user command. Each octet has the following enumeration value: radius(2) - send accounting info to radius server tacplus(5) - send accounting info to tacplus server none(6) - skip accounting Setting a zero length octet string invalidates all previous accounting methods.
OCT snAccountingExec	1.3.6.1.4.1.1991.1.1.3.15.3.3	OCTET STRING	read-write	A sequence of accounting methods. Each octet represents a method for telnet or SSH login accounting. Each octet has the following enumeration value: radius(2) - send accounting info to radius server tacplus(5) - send accounting info to tacplus server none(6) - skip accounting Setting a zero length octet string invalidates all previous accounting methods.
OCT snAccountingSystem	1.3.6.1.4.1.1991.1.1.3.15.3.4	OCTET STRING	read-write	A sequence of accounting methods. Each octet represents a method to account for the system related events. Each octet has the following enumeration value: radius(2) - send accounting info to radius server tacplus(5) - send accounting info to tacplus server none(6) - skip accounting Setting a zero length octet string invalidates all previous accounting methods.
snArpInfo	1.3.6.1.4.1.1991.1.1.3.22
snAtmInterface	1.3.6.1.4.1.1991.1.1.3.3.2.3
snAuthentication	1.3.6.1.4.1.1991.1.1.3.15.1
snAuthorization	1.3.6.1.4.1.1991.1.1.3.15.2
INT snAuthorizationCommandLevel	1.3.6.1.4.1.1991.1.1.3.15.2.2	INTEGER	read-write	Commands, which are equal to and less than the specified command level here needs to be authorized. Possible enumeration values: 0 - Privilege level 0 4 - Privilege level 4 5 - Privilege level 5.
OCT snAuthorizationCommandMethods	1.3.6.1.4.1.1991.1.1.3.15.2.1	OCTET STRING	read-write	A sequence of authorization methods. Each octet represents a method to authorize the user command. Each octet has the following value: radius(2) - authorize by requesting radius server tacplus(5) - authorize by requesting tacplus server none(6) - skip authorization Setting a zero length octet string invalidates all previous authorization methods.
OCT snAuthorizationExec	1.3.6.1.4.1.1991.1.1.3.15.2.3	OCTET STRING	read-write	A sequence of exec authorization methods. Each octet represents a method for telnet or SSH login authorization. Each octet has the following enumeration value: radius(2) - send exec authorization request to radius server tacplus(5) - send exec authorization request to tacplus server none(6) - no exec authorization Setting a zero length octet string invalidates all authorization methods.
snCAR	1.3.6.1.4.1.1991.1.1.3.16
OCT snDhcpGatewayListAddrList	1.3.6.1.4.1.1991.1.1.3.8.1.1.2	OCTET STRING	read-write	The DHCP gateway address list for each DHCP gateway list ID. This list contains 1 to 8 IP addresses represented by octet string.
snDhcpGatewayListEntry	1.3.6.1.4.1.1991.1.1.3.8.1.1		not-accessible	An entry in the IP Port Address table.
INT snDhcpGatewayListId	1.3.6.1.4.1.1991.1.1.3.8.1.1.1	INTEGER	read-only	The ID for a DHCP gateway list entry.
snDhcpGatewayListInfo	1.3.6.1.4.1.1991.1.1.3.8
INT snDhcpGatewayListRowStatus	1.3.6.1.4.1.1991.1.1.3.8.1.1.3	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row or modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
snDhcpGatewayListTable	1.3.6.1.4.1.1991.1.1.3.8.1		not-accessible	A table of DHCP gateway list of addresses.
STR snDnsDomainName	1.3.6.1.4.1.1991.1.1.3.9.1	DisplayString	read-write	DNS Domain Name string.
OCT snDnsGatewayIpAddrList	1.3.6.1.4.1.1991.1.1.3.9.2	OCTET STRING	read-write	The DNS Gateway IP address list. This list contains 4 IP addresses represented by octet string.
snDnsInfo	1.3.6.1.4.1.1991.1.1.3.9
snDosAttack	1.3.6.1.4.1.1991.1.1.3.14.3
snDosAttackGlobal	1.3.6.1.4.1.1991.1.1.3.14.3.1
C32 snDosAttackICMPBlockCount	1.3.6.1.4.1.1991.1.1.3.14.3.1.2	Counter32	read-only	ICMP block counter.
C32 snDosAttackICMPDropCount	1.3.6.1.4.1.1991.1.1.3.14.3.1.1	Counter32	read-only	ICMP drop counter.
I32 snDosAttackPort	1.3.6.1.4.1.1991.1.1.3.14.3.2.1.1	Integer32	read-only	ifIndex value of a port.
snDosAttackPortEntry	1.3.6.1.4.1.1991.1.1.3.14.3.2.1		not-accessible	An entry of the denial of service attack port table.
C32 snDosAttackPortICMPBlockCount	1.3.6.1.4.1.1991.1.1.3.14.3.2.1.3	Counter32	read-only	ICMP block counter.
C32 snDosAttackPortICMPDropCount	1.3.6.1.4.1.1991.1.1.3.14.3.2.1.2	Counter32	read-only	ICMP drop counter.
C32 snDosAttackPortSYNBlockCount	1.3.6.1.4.1.1991.1.1.3.14.3.2.1.5	Counter32	read-only	SYN block counter.
C32 snDosAttackPortSYNDropCount	1.3.6.1.4.1.1991.1.1.3.14.3.2.1.4	Counter32	read-only	SYN drop counter.
snDosAttackPortTable	1.3.6.1.4.1.1991.1.1.3.14.3.2		not-accessible	Denial of service attack port table.
C32 snDosAttackSYNBlockCount	1.3.6.1.4.1.1991.1.1.3.14.3.1.4	Counter32	read-only	SYN block counter.
C32 snDosAttackSYNDropCount	1.3.6.1.4.1.1991.1.1.3.14.3.1.3	Counter32	read-only	SYN drop counter.
snEthernetInterface	1.3.6.1.4.1.1991.1.1.3.3.2.1
snFdbEntry	1.3.6.1.4.1.1991.1.1.3.4.1.1		not-accessible	Each entry represents the information of a static MAC station.
snFdbInfo	1.3.6.1.4.1.1991.1.1.3.4
INT snFdbRowStatus	1.3.6.1.4.1.1991.1.1.3.4.1.1.7	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
PHY snFdbStationAddr	1.3.6.1.4.1.1991.1.1.3.4.1.1.2	PhysAddress	read-write	The snFdbs physical address. The physical address represents a MAC Station.
I32 snFdbStationEntrySize	1.3.6.1.4.1.1991.1.1.3.1.23	Integer32	read-only	The size of each Fdb station table entry.
NUM snFdbStationIf	1.3.6.1.4.1.1991.1.1.3.4.1.1.8	InterfaceIndex	read-write	Station interface index.
INT snFdbStationIndex	1.3.6.1.4.1.1991.1.1.3.4.1.1.1	INTEGER	read-only	The FDB Station index to the Fdb Station Table.
I32 snFdbStationPort	1.3.6.1.4.1.1991.1.1.3.4.1.1.3	Integer32	read-write	Station slot/port number. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only).
INT snFdbStationQos	1.3.6.1.4.1.1991.1.1.3.4.1.1.5	INTEGER	read-write	The Stand alone stackable station Qos Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron switch station Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
INT snFdbStationType	1.3.6.1.4.1.1991.1.1.3.4.1.1.6	INTEGER	read-write	The station type values are: notSupported -- a read value only : this product does not support MultiLayer Switching. host -- any MAC station. router -- a router-typed station.
snFdbTable	1.3.6.1.4.1.1991.1.1.3.4.1		not-accessible	This table contains snFdb information for each station known to the system, one entry per station.
I32 snFdbTableCurEntry	1.3.6.1.4.1.1991.1.1.3.1.9	Integer32	read-only	The current total entry number of FDB are configured.
INT snFdbTableStationFlush	1.3.6.1.4.1.1991.1.1.3.1.10	INTEGER	read-write	The following values of the flush state can only be read: normal(1)... normal state error(2)... operation failed flushing(4)... in process The following value can be written: flush(3).....do flush The agent will return a response even before the flush is done. And the read value will be flushing until flush is done. And the flush request will be rejected until error or normal.
INT snFdbVLanId	1.3.6.1.4.1.1991.1.1.3.4.1.1.4	INTEGER	read-write	The Station VLan ID.
snFDP	1.3.6.1.4.1.1991.1.1.3.20
snFdpCache	1.3.6.1.4.1.1991.1.1.3.20.1.2
OCT snFdpCacheAddress	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.5	OCTET STRING	read-only	The (first) network-layer address of the device as reported in the most recent FDP/CDP message in the following format: IP address: 4 octets, ip(1) IPX address: 10 octets, ipx(2) First 4-octet as the network number Second 6-octet as the host number Appletalk address: 3 octets, appletalk(3) First 2-octet as the network number Second 1-octet as the host number
INT snFdpCacheAddressType	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.4	INTEGER	read-only	An indication of the type of address contained in the corresponding instance of snFdpCacheAddress.
STR snFdpCacheCapabilities	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.9	DisplayString	read-only	The Device's Functional Capabilities as reported in the most recent FDP/CDP message.
snFdpCachedAddr	1.3.6.1.4.1.1991.1.1.3.20.1.4
I32 snFdpCachedAddrDeviceAddrEntryIndex	1.3.6.1.4.1.1991.1.1.3.20.1.4.1.1.3	Integer32	not-accessible	A unique vlaue for address entry in device from which FDP/CDP messages are being received.
I32 snFdpCachedAddrDeviceIndex	1.3.6.1.4.1.1991.1.1.3.20.1.4.1.1.2	Integer32	not-accessible	A unique vlaue for each device from which FDP/CDP messages are being received.
snFdpCachedAddressEntry	1.3.6.1.4.1.1991.1.1.3.20.1.4.1.1		not-accessible	An entry (conceptual row) in the snFdpCacheAddressTable, containing one cached address from FDP/CDP messages.
snFdpCachedAddressTable	1.3.6.1.4.1.1991.1.1.3.20.1.4.1		not-accessible	Cached address table from receiving FDP/CDP messages.
NUM snFdpCachedAddrIfIndex	1.3.6.1.4.1.1991.1.1.3.20.1.4.1.1.1	InterfaceIndex	not-accessible	The ifIndex value of the local interface.
INT snFdpCachedAddrType	1.3.6.1.4.1.1991.1.1.3.20.1.4.1.1.4	INTEGER	read-only	An indication of the type of address contained in the corresponding instance of snFdpCacheAddrValue.
OCT snFdpCachedAddrValue	1.3.6.1.4.1.1991.1.1.3.20.1.4.1.1.5	OCTET STRING	read-only	The network-layer address of the device SNMP-agent as reported in the most recent FDP/CDP message in the following format: IP address: 4 octets, ip(1) IPX address: 10 octets, ipx(2) First 4-octet as the network number Second 6-octet as the host number Appletalk address: 3 octets, appletalk(3) First 2-octet as the network number Second 1-octet as the host number
I32 snFdpCacheDefaultTrafficeVlanIdForDualMode	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.15	Integer32	read-only	Default traffic vlan id for neighbor device dual-mode port
STR snFdpCacheDeviceId	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.3	DisplayString	read-only	The Device-ID string as reported in the most recent FDP/CDP message. The zero-length string indicates no Device-ID field (TLV) was reported in the most recent FDP/CDP message.
I32 snFdpCacheDeviceIndex	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.2	Integer32	not-accessible	Identification of a device, which sent FDP/CDP messages
STR snFdpCacheDevicePort	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.7	DisplayString	read-only	The Port-ID string as reported in the most recent FDP/CDP message. This will typically be the value of the ifName object (e.g., Ethernet0). The zero-length string indicates no Port-ID field (TLV) was reported in the most recent FDP/CDP message.
snFdpCacheEntry	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1		not-accessible	An entry in the snFdpCacheTable, having the information received via FDP/CDP on one interface from one device. Entries appear when a FDP/CDP advertisement is received from a neighbor device. Entries disappear when FDP/CDP is disabled on the interface, or globally.
NUM snFdpCacheIfIndex	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.1	InterfaceIndex	not-accessible	ifIndex value of the local interface.
INT snFdpCacheIsAggregateVlan	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.11	INTEGER	read-only	Neighbor device is in aggregated-vlan.
STR snFdpCachePlatform	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.8	DisplayString	read-only	The Device's Hardware Platform as reported in the most recent FDP/CDP message. The zero-length string indicates that no Platform field (TLV) was reported in the most recent FDP/CDP message.
INT snFdpCachePortTagMode	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.14	INTEGER	read-only	Neighbor device port tag mode
OCT snFdpCachePortVlanMask	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.13	OCTET STRING	read-only	Neighbor device port VLAN masks in 512-byte octet string.
snFdpCacheTable	1.3.6.1.4.1.1991.1.1.3.20.1.2.1		not-accessible	The table for the cached information obtained via receiving FDP/CDP messages.
I32 snFdpCacheTagType	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.12	Integer32	read-only	Neighbor device tag-type.
INT snFdpCacheVendorId	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.10	INTEGER	read-only	Indicates the entry received by either FDP or CDP.
STR snFdpCacheVersion	1.3.6.1.4.1.1991.1.1.3.20.1.2.1.1.6	DisplayString	read-only	Version string as reported in the most recent FDP/CDP message.
snFdpGlobal	1.3.6.1.4.1.1991.1.1.3.20.1.3
INT snFdpGlobalCdpRun	1.3.6.1.4.1.1991.1.1.3.20.1.3.4	INTEGER	read-write	An indication of whether the Cisco Discovery Protocol is currently running. CDP entries in snFdpCacheTable are deleted when CDP is disabled.
INT snFdpGlobalHoldTime	1.3.6.1.4.1.1991.1.1.3.20.1.3.3	INTEGER	read-write	The time for the receiving device holds FDP message. The default value is 180 seconds.
INT snFdpGlobalMessageInterval	1.3.6.1.4.1.1991.1.1.3.20.1.3.2	INTEGER	read-write	The interval at which FDP messages are to be generated. The default value is 60 seconds.
INT snFdpGlobalRun	1.3.6.1.4.1.1991.1.1.3.20.1.3.1	INTEGER	read-write	The flag, whether the Foundry Discovery Protocol is currently running. FDP entries in snFdpCacheTable are deleted when FDP is disabled.
snFdpInterface	1.3.6.1.4.1.1991.1.1.3.20.1.1
INT snFdpInterfaceCdpEnable	1.3.6.1.4.1.1991.1.1.3.20.1.1.1.1.3	INTEGER	read-write	The flag, whether the Cisco Discovery Protocol is currently running on this interface. It has no effect when CDP is disabled (snCdpGlobalRun = FALSE).
snFdpInterfaceEntry	1.3.6.1.4.1.1991.1.1.3.20.1.1.1.1		not-accessible	An entry in the snFdpInterfaceTable, having the status of FDP on an interface.
INT snFdpInterfaceFdpEnable	1.3.6.1.4.1.1991.1.1.3.20.1.1.1.1.2	INTEGER	read-write	The flag, whether the Foundry Discovery Protocol is currently running on this interface. It has no effect when FDP is disabled (snFdpGlobalRun = FALSE).
NUM snFdpInterfaceIfIndex	1.3.6.1.4.1.1991.1.1.3.20.1.1.1.1.1	InterfaceIndex	not-accessible	ifIndex value of the local interface.
snFdpInterfaceTable	1.3.6.1.4.1.1991.1.1.3.20.1.1.1		not-accessible	Status of FDP on the device's interfaces.
snFdpMIBObjects	1.3.6.1.4.1.1991.1.1.3.20.1
snGreTunnelInterface	1.3.6.1.4.1.1991.1.1.3.3.2.6
snIfIndexLookup2Entry	1.3.6.1.4.1.1991.1.1.3.3.8.1		not-accessible
I32 snIfIndexLookup2IfIndex	1.3.6.1.4.1.1991.1.1.3.3.8.1.1	Integer32	not-accessible
NUM snIfIndexLookup2InterfaceId	1.3.6.1.4.1.1991.1.1.3.3.8.1.2	InterfaceId2	read-only
snIfIndexLookup2Table	1.3.6.1.4.1.1991.1.1.3.3.8		not-accessible
snIfIndexLookupEntry	1.3.6.1.4.1.1991.1.1.3.3.4.1		not-accessible
I32 snIfIndexLookupIfIndex	1.3.6.1.4.1.1991.1.1.3.3.4.1.1	Integer32	read-only
NUM snIfIndexLookupInterfaceId	1.3.6.1.4.1.1991.1.1.3.3.4.1.2	InterfaceId	read-only
snIfIndexLookupTable	1.3.6.1.4.1.1991.1.1.3.3.4		not-accessible
snIfMediaInfoEntry	1.3.6.1.4.1.1991.1.1.3.3.9.1		not-accessible	An entry in the Interface Media Information table. The ifIndices of ethernet interfaces will be used to index this table.
snIfMediaInfoTable	1.3.6.1.4.1.1991.1.1.3.3.9		not-accessible	This table lists the information of the media device (SFP/XFP/Copper) installed in the physical port. Only the ifIndices of Ethernet ports those are associated with the operational cards will be included in this table.
STR snIfMediaPartNumber	1.3.6.1.4.1.1991.1.1.3.3.9.1.4	DisplayString	read-only	The media vendor part number.
STR snIfMediaSerialNumber	1.3.6.1.4.1.1991.1.1.3.3.9.1.5	DisplayString	read-only	The vendor serial number of the media device.
STR snIfMediaType	1.3.6.1.4.1.1991.1.1.3.3.9.1.1	DisplayString	read-only	The type of the media installed in the physical port.
STR snIfMediaVendorName	1.3.6.1.4.1.1991.1.1.3.3.9.1.2	DisplayString	read-only	The media vendor name, full name of the corporation.
STR snIfMediaVersion	1.3.6.1.4.1.1991.1.1.3.3.9.1.3	DisplayString	read-only	The media vendor product version number.
snIfOpticalLaneMonitoringEntry	1.3.6.1.4.1.1991.1.1.3.3.10.1		not-accessible	Only the ifIndices of optical interfaces whose parameters need to be monitored will be used to index this table.
U32 snIfOpticalLaneMonitoringLane	1.3.6.1.4.1.1991.1.1.3.3.10.1.1	Unsigned32	not-accessible	The lane number of this 40G or 100G optic. LR4 and SR4 have 4 lanes per optic. LR10 has 10 lanes per optic.
STR snIfOpticalLaneMonitoringRxPower	1.3.6.1.4.1.1991.1.1.3.3.10.1.4	DisplayString	read-only	This object holds the value of the receiver optical signal power for the lane in the interface, measured in dBm, followed by whether this is a normal value, or high/low warning or alarm.
snIfOpticalLaneMonitoringTable	1.3.6.1.4.1.1991.1.1.3.3.10		not-accessible	This table lists the instrumented parameters of all lanes within a 40G Optic of type SR4 and LR4, 100G optic of type LR4 and LR10. LR4 and SR4 have 4 lanes per optic, LR10 has 10 lanes per optic.
STR snIfOpticalLaneMonitoringTemperature	1.3.6.1.4.1.1991.1.1.3.3.10.1.2	DisplayString	read-only	This object holds the value of the transmitter laser diode temperature for the lane in the interface. This object indicates the health of the transmitter. The format is xxx.yyyy C(elcius), followed by whether the measured value is normal, high/low alarm or high/low warning.
STR snIfOpticalLaneMonitoringTxBiasCurrent	1.3.6.1.4.1.1991.1.1.3.3.10.1.5	DisplayString	read-only	Tx Bias Current. It is measured in mA, and is followed by whether this is a normal value, or high/low warning or alarm.
STR snIfOpticalLaneMonitoringTxPower	1.3.6.1.4.1.1991.1.1.3.3.10.1.3	DisplayString	read-only	This object holds the value of the transmitter optical signal power for the lane in the interface, measured in dBm, followed by whether this is a normal value, or high/low warning or alarm.
snIfOpticalMonitoringInfoEntry	1.3.6.1.4.1.1991.1.1.3.3.6.1		not-accessible	Only the ifIndices of optical interfaces whose parameters need to be monitored will be used to index this table.
snIfOpticalMonitoringInfoTable	1.3.6.1.4.1.1991.1.1.3.3.6		not-accessible	This table lists the instrumented parameters of all optical interfaces.
STR snIfOpticalMonitoringRxPower	1.3.6.1.4.1.1991.1.1.3.3.6.1.3	DisplayString	read-only	This object holds the value of the receiver optical signal power for the interface, measured in dBm, followed by whether this is a normal value, or high/low warning or alarm. For 100G LR4 and LR10 optic, this returns the aggregated Rx Power for all lanes.
STR snIfOpticalMonitoringTemperature	1.3.6.1.4.1.1991.1.1.3.3.6.1.1	DisplayString	read-only	This object holds the value of the transmitter laser diode temperature for the interface. This object indicates the health of the transmitter. The format is xxx.yyyy C(elcius), followed by whether the measured value is normal, high/low alarm or high/low warning. For 100G LR4 and LR10 optic, this returns the average temperature for all lanes.
STR snIfOpticalMonitoringTxBiasCurrent	1.3.6.1.4.1.1991.1.1.3.3.6.1.4	DisplayString	read-only	Tx Bias Current. It is measured in mA, and is followed by whether this is a normal value, or high/low warning or alarm. For 100G LR4 and LR10 optic, this returns the aggregated Tx Bias Current for all lanes.
STR snIfOpticalMonitoringTxPower	1.3.6.1.4.1.1991.1.1.3.3.6.1.2	DisplayString	read-only	This object holds the value of the transmitter optical signal power for the interface, measured in dBm, followed by whether this is a normal value, or high/low warning or alarm. For 100G LR4 and LR10 optic, this returns the aggregated Tx Power for all lanes.
C32 snIfRstpConfigBPDUReceived	1.3.6.1.4.1.1991.1.1.3.5.2.1.21	Counter32	read-only	RSTP configuration bridge protocol unit received counter.
C32 snIfRstpConfigBPDUTransmitted	1.3.6.1.4.1.1991.1.1.3.5.2.1.23	Counter32	read-only	RSTP configuration bridge protocol unit transmitted counter.
C32 snIfRstpTCNBPDUReceived	1.3.6.1.4.1.1991.1.1.3.5.2.1.22	Counter32	read-only	RSTP topology change notification bridge protocol unit received counter.
C32 snIfRstpTCNBPDUTransmitted	1.3.6.1.4.1.1991.1.1.3.5.2.1.24	Counter32	read-only	RSTP topology change notification bridge protocol unit transmitted counter.
C32 snIfStpBPDUReceived	1.3.6.1.4.1.1991.1.1.3.5.2.1.20	Counter32	read-only	STP/RSTP bridge protocol unit received counter.
C32 snIfStpBPDUTransmitted	1.3.6.1.4.1.1991.1.1.3.5.2.1.19	Counter32	read-only	STP/RSTP bridge protocol unit transmitted counter.
INT snIfStpCfgPathCost	1.3.6.1.4.1.1991.1.1.3.5.2.1.4	INTEGER	read-write	dot1dStpPortPathCost : The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN. Writing value zero to this object sets path cost to a default value which automatically changes according to port speed.
snIfStpEntry	1.3.6.1.4.1.1991.1.1.3.5.2.1		not-accessible	An entry in the snIfStpTable indicates the configuration on a specified port. A SNMP SET PDU for a row of the snIfStpTable requires the entired sequence of the MIB Objects in each snIfStpEntry stored in one PDU. Otherwise, GENERR return-value will be returned.
INT snIfStpOperPathCost	1.3.6.1.4.1.1991.1.1.3.5.2.1.17	INTEGER	read-only	dot1dStpPortPathCost : The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN. Reading value zero indicates an unknown path cost value because port speed cannot be determined due to speed auto sense in progress or port link is down.
INT snIfStpOperState	1.3.6.1.4.1.1991.1.1.3.5.2.1.5	INTEGER	read-only	For FastIron: By default, this mode is set to notActivated(0). notActivated(0)...the Port STP or RSTP entry is not configured and not in running mode. activated(1)......the Port STP or RSTP entry is enabled. For NetIron: By default, this mode is set to notActivated(0). notActivated(0)...the Port STP entry is not activated and not in running mode. activated(1)......the Port STP entry is activated and in running mode
T/F snIfStpPortAdminEdgePort	1.3.6.1.4.1.1991.1.1.3.5.2.1.15	TruthValue	read-write	The administrative value of the Edge Port parameter. A value of TRUE(1) indicates that this port should be assumed as an edge-port and a value of FALSE(2) indicates that this port should be assumed as a non-edge-port.
T/F snIfStpPortAdminPointToPoint	1.3.6.1.4.1.1991.1.1.3.5.2.1.16	TruthValue	read-write	The administrative point-to-point status of the LAN segment attached to this port. A value of TRUE(1) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of FALSE(2) indicates that this port should be treated as having a shared media connection.
T/F snIfStpPortAdminRstp	1.3.6.1.4.1.1991.1.1.3.5.2.1.13	TruthValue	read-write	Enable or disable RSTP of a port which is a member of a VLAN. If the VLAN is not operating in RSTP, this object will return FALSE(2) and this object is not writable.
BRI snIfStpPortDesignatedBridge	1.3.6.1.4.1.1991.1.1.3.5.2.1.11	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
I32 snIfStpPortDesignatedCost	1.3.6.1.4.1.1991.1.1.3.5.2.1.9	Integer32	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OCT snIfStpPortDesignatedPort	1.3.6.1.4.1.1991.1.1.3.5.2.1.12	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
BRI snIfStpPortDesignatedRoot	1.3.6.1.4.1.1991.1.1.3.5.2.1.10	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
NUM snIfStpPortNum	1.3.6.1.4.1.1991.1.1.3.5.2.1.2	InterfaceIndex	read-only	The port number of the Switch. It has the ifIndex value.
INT snIfStpPortPriority	1.3.6.1.4.1.1991.1.1.3.5.2.1.3	INTEGER	read-write	The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of dot1dStpPort.
T/F snIfStpPortProtocolMigration	1.3.6.1.4.1.1991.1.1.3.5.2.1.14	TruthValue	read-write	When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read.
INT snIfStpPortRole	1.3.6.1.4.1.1991.1.1.3.5.2.1.18	INTEGER	read-only	STP/RSTP port role.
INT snIfStpPortState	1.3.6.1.4.1.1991.1.1.3.5.2.1.8	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpPortEnable), this object will have a value of disabled(1).
snIfStpTable	1.3.6.1.4.1.1991.1.1.3.5.2		not-accessible	A specific snIfStpTable consists of a number of switch ports. This table only exists if only if snVLanByPortCfgTable exists and snVLanByPortCfgStpMode is enabled for each VLAN.
INT snIfStpVLanId	1.3.6.1.4.1.1991.1.1.3.5.2.1.1	INTEGER	read-only	The VLAN ID of the VLAN switch community.
snInterfaceId	1.3.6.1.4.1.1991.1.1.3.3.2
snInterfaceLookup2Entry	1.3.6.1.4.1.1991.1.1.3.3.7.1		not-accessible
I32 snInterfaceLookup2IfIndex	1.3.6.1.4.1.1991.1.1.3.3.7.1.2	Integer32	read-only
NUM snInterfaceLookup2InterfaceId	1.3.6.1.4.1.1991.1.1.3.3.7.1.1	InterfaceId2	not-accessible
snInterfaceLookup2Table	1.3.6.1.4.1.1991.1.1.3.3.7		not-accessible
snInterfaceLookupEntry	1.3.6.1.4.1.1991.1.1.3.3.3.1		not-accessible
I32 snInterfaceLookupIfIndex	1.3.6.1.4.1.1991.1.1.3.3.3.1.2	Integer32	read-only
NUM snInterfaceLookupInterfaceId	1.3.6.1.4.1.1991.1.1.3.3.3.1.1	InterfaceId	read-only
snInterfaceLookupTable	1.3.6.1.4.1.1991.1.1.3.3.3		not-accessible
snLoopbackInterface	1.3.6.1.4.1.1991.1.1.3.3.2.5
snMac	1.3.6.1.4.1.1991.1.1.3.24
snMacAuth	1.3.6.1.4.1.1991.1.1.3.28
snMacFilter	1.3.6.1.4.1.1991.1.1.3.10
INT snMacFilterAction	1.3.6.1.4.1.1991.1.1.3.10.1.1.2	INTEGER	read-write	Action to take if the Mac packet match with this filter.
MAC snMacFilterDestMac	1.3.6.1.4.1.1991.1.1.3.10.1.1.5	MacAddress	read-write	Destination MAC address.
MAC snMacFilterDestMask	1.3.6.1.4.1.1991.1.1.3.10.1.1.6	MacAddress	read-write	Destination MAC subnet mask.
snMacFilterEntry	1.3.6.1.4.1.1991.1.1.3.10.1.1		not-accessible	An entry in the MAC filter table.
INT snMacFilterFrameType	1.3.6.1.4.1.1991.1.1.3.10.1.1.8	INTEGER	read-write	Frame Type: ethernet-type, LLC and SNAP types
INT snMacFilterFrameTypeNum	1.3.6.1.4.1.1991.1.1.3.10.1.1.9	INTEGER	read-write	Frame Type Number. 0 means NA
snMacFilterIfAccessEntry	1.3.6.1.4.1.1991.1.1.3.10.3.1		not-accessible	An entry in the MAC Filter Port access table.
OCT snMacFilterIfAccessFilters	1.3.6.1.4.1.1991.1.1.3.10.3.1.2	OCTET STRING	read-write	1st octet correspond to 1st filter number and so on.
NUM snMacFilterIfAccessPortIndex	1.3.6.1.4.1.1991.1.1.3.10.3.1.1	InterfaceIndex	read-only	The port/interface index.
INT snMacFilterIfAccessRowStatus	1.3.6.1.4.1.1991.1.1.3.10.3.1.3	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
snMacFilterIfAccessTable	1.3.6.1.4.1.1991.1.1.3.10.3		not-accessible	MAC Filter port access table.
I32 snMacFilterIndex	1.3.6.1.4.1.1991.1.1.3.10.1.1.1	Integer32	read-only	The table index for a filter entry.
INT snMacFilterOperator	1.3.6.1.4.1.1991.1.1.3.10.1.1.7	INTEGER	read-write	Type of comparison to perform.
snMacFilterPortAccessEntry	1.3.6.1.4.1.1991.1.1.3.10.2.1		not-accessible	An entry in the MAC Filter Port access table.
OCT snMacFilterPortAccessFilters	1.3.6.1.4.1.1991.1.1.3.10.2.1.2	OCTET STRING	read-write	1st octet correspond to 1st filter number and so on.
INT snMacFilterPortAccessPortIndex	1.3.6.1.4.1.1991.1.1.3.10.2.1.1	INTEGER	read-only	The port index. For FastIron/NetIron products, port index value is from 1 to 42 For BigIron products, port index is an encoded number: The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number. For virtual router interface, slot number is 15, port number is the virtual router port from 1 to 60. Therefore, port index value for BigIron is from 257 to 3900.
INT snMacFilterPortAccessRowStatus	1.3.6.1.4.1.1991.1.1.3.10.2.1.3	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
snMacFilterPortAccessTable	1.3.6.1.4.1.1991.1.1.3.10.2		not-accessible	MAC Filter port access table.
INT snMacFilterRowStatus	1.3.6.1.4.1.1991.1.1.3.10.1.1.10	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
MAC snMacFilterSourceMac	1.3.6.1.4.1.1991.1.1.3.10.1.1.3	MacAddress	read-write	Source MAC address.
MAC snMacFilterSourceMask	1.3.6.1.4.1.1991.1.1.3.10.1.1.4	MacAddress	read-write	Source MAC subnet mask.
snMacFilterTable	1.3.6.1.4.1.1991.1.1.3.10.1		not-accessible	MAC filter table.
snMacSecurity	1.3.6.1.4.1.1991.1.1.3.24.1
INT snMacStationVLanId	1.3.6.1.4.1.1991.1.1.3.1.32	INTEGER	read-write	This VLAN ID controls filtering of the Forwarding Database table in the standard Bridge MIB (dot1dTpFdbTable). Since the dot1dTpFdbTable contains MAC addresses associated with each of the ports in the bridge, and each MAC address can be associated with different VLANs, the snMacStationVLanId can be used by users to specify which VLAN's MAC Station information the dot1dTpFdbTable should provide. If this variable is set to zero (the default value), all MAC station entries will be returned when the dot1dTpFdbTable is retrieved. The VLAN-aware dot1qTpFdbTable described in RFC 2674 should be used as a replacement for this variable.
snMetroRing	1.3.6.1.4.1.1991.1.1.3.29
snMgmtEthernetInterface	1.3.6.1.4.1.1991.1.1.3.3.2.10
snMplsTunnelInterface	1.3.6.1.4.1.1991.1.1.3.3.2.8
snMSTrunkEntry	1.3.6.1.4.1.1991.1.1.3.6.2.1		not-accessible	An entry of the snMSTrunkTable.
snMSTrunkIfEntry	1.3.6.1.4.1.1991.1.1.3.6.3.1		not-accessible	An entry of the snMSTrunkIfTable.
I32 snMSTrunkIfIndex	1.3.6.1.4.1.1991.1.1.3.6.3.1.1	Integer32	read-only	The primary port(IfIndex) of a trunk group. For module with Gig ports, primary port is port 1, 3, 5, 7. For module with 10/100 ports, primary port is port 1, 5, 9, 13, 17, 21.
OCT snMSTrunkIfList	1.3.6.1.4.1.1991.1.1.3.6.3.1.2	OCTET STRING	read-write	A list of interface indices which are the port membership of a trunk group. Each interface index is a 16-bit integer in big endian order. The first interface/port index must be the primary port(ifIndex) index.
INT snMSTrunkIfRowStatus	1.3.6.1.4.1.1991.1.1.3.6.3.1.4	INTEGER	read-write	To create or delete a table entry.
snMSTrunkIfTable	1.3.6.1.4.1.1991.1.1.3.6.3		not-accessible	A table contains the configuration of port members of multi-slot trunk groups.
INT snMSTrunkIfType	1.3.6.1.4.1.1991.1.1.3.6.3.1.3	INTEGER	read-write	The trunk connection type which specifies what device the trunk ports are connected to.
I32 snMSTrunkPortIndex	1.3.6.1.4.1.1991.1.1.3.6.2.1.1	Integer32	read-only	The primary port of a trunk group. For module with Gig ports, primary port is port 1, 3, 5, 7. For module with 10/100 ports, primary port is port 1, 5, 9, 13, 17, 21.
OCT snMSTrunkPortList	1.3.6.1.4.1.1991.1.1.3.6.2.1.2	OCTET STRING	read-write	A list of port indices which are the port membership of a trunk group. Each port index is a 16-bit integer in big endian order. The first port index must be the primary port index.
INT snMSTrunkRowStatus	1.3.6.1.4.1.1991.1.1.3.6.2.1.4	INTEGER	read-write	To create or delete a table entry.
snMSTrunkTable	1.3.6.1.4.1.1991.1.1.3.6.2		not-accessible	A table contains the configuration of port members of multi-slot trunk groups.
INT snMSTrunkType	1.3.6.1.4.1.1991.1.1.3.6.2.1.3	INTEGER	read-write	The trunk connection type which specifies what device the trunk ports are connected to.
snNetFlow	1.3.6.1.4.1.1991.1.1.3.18
I32 snNetFlowAggregationActiveTimeout	1.3.6.1.4.1.1991.1.1.3.18.3.1.6	Integer32	read-write	Maximum time an active flow can be in the aggregation cache
INT snNetFlowAggregationEnable	1.3.6.1.4.1.1991.1.1.3.18.3.1.8	INTEGER	read-write	Enable/disable NetFlow aggregation for this aggregation scheme.
snNetFlowAggregationEntry	1.3.6.1.4.1.1991.1.1.3.18.3.1		not-accessible	A row in the NetFlow Aggregation table.
I32 snNetFlowAggregationInactiveTimeout	1.3.6.1.4.1.1991.1.1.3.18.3.1.7	Integer32	read-write	Maximum time an inactive flow can be in the aggregation cache
INT snNetFlowAggregationIndex	1.3.6.1.4.1.1991.1.1.3.18.3.1.1	INTEGER	read-only	The Aggregation scheme ID
IP snNetFlowAggregationIp	1.3.6.1.4.1.1991.1.1.3.18.3.1.2	IpAddress	read-write	The NetFlow aggregation collector ip address.
I32 snNetFlowAggregationNumberOfCacheEntries	1.3.6.1.4.1.1991.1.1.3.18.3.1.5	Integer32	read-write	Number of cache entries for aggregation scheme
INT snNetFlowAggregationRowStatus	1.3.6.1.4.1.1991.1.1.3.18.3.1.9	INTEGER	read-write	To create or delete a NetFlow collector table entry.
NUM snNetFlowAggregationSourceInterface	1.3.6.1.4.1.1991.1.1.3.18.3.1.4	InterfaceIndex	read-write	The ifIndex value to specify source port to export NetFlow aggregation packet. Value 0 to indicate default outgoing port.
snNetFlowAggregationTable	1.3.6.1.4.1.1991.1.1.3.18.3		not-accessible	A table of each NetFlow aggregation scheme information.
I32 snNetFlowAggregationUdpPort	1.3.6.1.4.1.1991.1.1.3.18.3.1.3	Integer32	read-write	The NetFlow aggregation collector UDP port number.
snNetFlowCollectorEntry	1.3.6.1.4.1.1991.1.1.3.18.2.1		not-accessible	A row in the NetFlow collector table.
INT snNetFlowCollectorIndex	1.3.6.1.4.1.1991.1.1.3.18.2.1.1	INTEGER	read-only	The index to the NetFlow collector table.
IP snNetFlowCollectorIp	1.3.6.1.4.1.1991.1.1.3.18.2.1.2	IpAddress	read-write	The NetFlow collector ip address.
INT snNetFlowCollectorRowStatus	1.3.6.1.4.1.1991.1.1.3.18.2.1.5	INTEGER	read-write	To create or delete a NetFlow collector table entry.
NUM snNetFlowCollectorSourceInterface	1.3.6.1.4.1.1991.1.1.3.18.2.1.4	InterfaceIndex	read-write	The ifIndex value to specify source port to export NetFlow packet. Value 0 to indicate default outgoing port.
snNetFlowCollectorTable	1.3.6.1.4.1.1991.1.1.3.18.2		not-accessible	A table of each NetFlow collector information.
I32 snNetFlowCollectorUdpPort	1.3.6.1.4.1.1991.1.1.3.18.2.1.3	Integer32	read-write	The NetFlow collector UDP port number.
I32 snNetFlowGblActiveTimeout	1.3.6.1.4.1.1991.1.1.3.18.1.4	Integer32	read-write	Maximum time an active flow can be in the NetFlow cache (minutes: 1..60)
INT snNetFlowGblEnable	1.3.6.1.4.1.1991.1.1.3.18.1.1	INTEGER	read-write	Enable/disable NetFlow export operation.
I32 snNetFlowGblInactiveTimeout	1.3.6.1.4.1.1991.1.1.3.18.1.5	Integer32	read-write	Maximum time an inactive flow can be in the NetFlow cache (seconds: 10..600)
I32 snNetFlowGblProtocolDisable	1.3.6.1.4.1.1991.1.1.3.18.1.3	Integer32	read-write	bit 0 - other, disable all protocols export except UDP and TCP bit 1 - tcp, disable TCP protocol export bit 2 - udp, disable UDP protocol export
INT snNetFlowGblVersion	1.3.6.1.4.1.1991.1.1.3.18.1.2	INTEGER	read-write	NetFlow export version.
snNetFlowGlb	1.3.6.1.4.1.1991.1.1.3.18.1
snNetFlowIfEntry	1.3.6.1.4.1.1991.1.1.3.18.4.1		not-accessible	Entry containing the type of switching performed on that interface.
INT snNetFlowIfFlowSwitching	1.3.6.1.4.1.1991.1.1.3.18.4.1.2	INTEGER	read-write	To enable/disable flow switching in a particular interface: disable (0) - no flow switching enable (1) - flow switching
NUM snNetFlowIfIndex	1.3.6.1.4.1.1991.1.1.3.18.4.1.1	InterfaceIndex	read-only	A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.
snNetFlowIfTable	1.3.6.1.4.1.1991.1.1.3.18.4		not-accessible	A list of interface entries. The number of entries is given by the value of ifNumber.
snNTP	1.3.6.1.4.1.1991.1.1.3.11
snNTPGeneral	1.3.6.1.4.1.1991.1.1.3.11.1
INT snNTPPollInterval	1.3.6.1.4.1.1991.1.1.3.11.1.1	INTEGER	read-write	Interval specifies how often to poll the NTP server. Each unit is one second. This object is not supported in NI devices from R5.3
snNTPServerEntry	1.3.6.1.4.1.1991.1.1.3.11.2.1		not-accessible	An entry in the NTP server table.
IP snNTPServerIp	1.3.6.1.4.1.1991.1.1.3.11.2.1.1	IpAddress	read-only	NTP server IP address.
INT snNTPServerRowStatus	1.3.6.1.4.1.1991.1.1.3.11.2.1.3	INTEGER	read-write	To create or delete a NTP server table entry.
snNTPServerTable	1.3.6.1.4.1.1991.1.1.3.11.2		not-accessible	NTP (Network Time Protocol) server table.
INT snNTPServerVersion	1.3.6.1.4.1.1991.1.1.3.11.2.1.2	INTEGER	read-write	NTP server version.
INT snNTPSummerTimeEnable	1.3.6.1.4.1.1991.1.1.3.11.1.3	INTEGER	read-write	Enable/Disable daylight saving time. This enables daylight saving time for time/date starting 02:00:00 of first Sunday in April and ending 02:00:00 of last Sunday in October every year.
INT snNTPSync	1.3.6.1.4.1.1991.1.1.3.11.1.5	INTEGER	read-write	Initiate time synchronization to the NTP servers. For set operation, only 'synchronize(2)' is accepted. For get operation, always return 'other(1)'. This object is not supported in NI devices from R5.3
OCT snNTPSystemClock	1.3.6.1.4.1.1991.1.1.3.11.1.4	OCTET STRING	read-write	System clock, in the following format: octet 0: seconds after the minute [0-60] octet 1: minutes after the hour [0-59] octet 2: hours since midnight [0-23] octet 3: day of the month [1-31] octet 4: months since January [0-11] octet 5: years since 1900 octet 6: days since Sunday [0-6] Setting this object requires valid value in octets 0 to 5, and zero in octet 6. System clock can be disabled by setting zero to all octets.
INT snNTPTimeZone	1.3.6.1.4.1.1991.1.1.3.11.1.2	INTEGER	read-write	Time zone.
snPortMacGlobalSecurity	1.3.6.1.4.1.1991.1.1.3.24.1.2
U32 snPortMacGlobalSecurityAgeOutTime	1.3.6.1.4.1.1991.1.1.3.24.1.2.2	Unsigned32	read-write	The amount of time, in minutes, MAC addresses learned on this device will remain secure. It allows configurable values in the range of 0-1440. 0 means no aging permanently.
U32 snPortMacGlobalSecurityAutosave	1.3.6.1.4.1.1991.1.1.3.24.1.2.3	Unsigned32	read-write	The port security autosave value for this device. It allows configurable values 0 and also in the range of 15-1440. The value 0 means no autosave.
INT snPortMacGlobalSecurityFeature	1.3.6.1.4.1.1991.1.1.3.24.1.2.1	INTEGER	read-write	Port security for this device can be either disabled or enabled.
snPortMacSecurity	1.3.6.1.4.1.1991.1.1.3.24.1.1
U32 snPortMacSecurityAgeLeft	1.3.6.1.4.1.1991.1.1.3.24.1.1.1.1.5	Unsigned32	read-only	The number of minutes the MAC address will remain secure before being aged out. 0 means no aging.
MAC snPortMacSecurityAutosaveMacAddress	1.3.6.1.4.1.1991.1.1.3.24.1.1.5.1.4	MacAddress	read-only	The secure MAC address for this local Ethernet interface on which the secure MAC Address is autosaved.
snPortMacSecurityAutosaveMacEntry	1.3.6.1.4.1.1991.1.1.3.24.1.1.5.1		not-accessible	An entry in the snPortMacSecurityAutosaveMacTable
I32 snPortMacSecurityAutosaveMacIfIndex	1.3.6.1.4.1.1991.1.1.3.24.1.1.5.1.1	Integer32	read-only	ifIndex value of the local Ethernet interface on which MAC security is configured.
U32 snPortMacSecurityAutosaveMacQueryIndex	1.3.6.1.4.1.1991.1.1.3.24.1.1.5.1.3	Unsigned32	read-only	Entry index within the given resource of local Ethernet interface on which MAC security is autosaved.
INT snPortMacSecurityAutosaveMacResource	1.3.6.1.4.1.1991.1.1.3.24.1.1.5.1.2	INTEGER	read-only	The MAC address was autosaved using local or shared resources.
snPortMacSecurityAutosaveMacTable	1.3.6.1.4.1.1991.1.1.3.24.1.1.5		not-accessible	Autosave MAC addresses of port MAC security on the device's interfaces.
snPortMacSecurityEntry	1.3.6.1.4.1.1991.1.1.3.24.1.1.1.1		not-accessible	An entry in the snPortMacSecurityTable
U32 snPortMacSecurityIfIndex	1.3.6.1.4.1.1991.1.1.3.24.1.1.1.1.1	Unsigned32	read-only	ifIndex value of the local Ethernet interface on which MAC security is configured.
U32 snPortMacSecurityIntfContentAgeOutTime	1.3.6.1.4.1.1991.1.1.3.24.1.1.3.1.6	Unsigned32	read-write	The amount of time, in minutes, MAC addresses learned on this interface will remain secure. It allows configurable values 0-1440. 0 means no aging permanently.
snPortMacSecurityIntfContentEntry	1.3.6.1.4.1.1991.1.1.3.24.1.1.3.1		not-accessible	An entry in the snPortMacSecurityIntfContentTable
NUM snPortMacSecurityIntfContentIfIndex	1.3.6.1.4.1.1991.1.1.3.24.1.1.3.1.1	InterfaceIndex	not-accessible	In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2863.
U32 snPortMacSecurityIntfContentMaxLockedMacAllowed	1.3.6.1.4.1.1991.1.1.3.24.1.1.3.1.7	Unsigned32	read-write	Maximum number of security MAC addresses can be locked to this interface.
INT snPortMacSecurityIntfContentSecurity	1.3.6.1.4.1.1991.1.1.3.24.1.1.3.1.2	INTEGER	read-write	Port security for this interface can be either disabled or enabled.
U32 snPortMacSecurityIntfContentShutdownTime	1.3.6.1.4.1.1991.1.1.3.24.1.1.3.1.4	Unsigned32	read-write	If snPortMacSecurityIntfContentViolationType is shutdown(1), this value gives the number of seconds this interface is shut down when violation occurs. In the shutdown(1) case, 0 means interface is permanently down. If snPortMacSecurityIntfContentViolationType is restrict(2), this value will be always 0.
U32 snPortMacSecurityIntfContentShutdownTimeLeft	1.3.6.1.4.1.1991.1.1.3.24.1.1.3.1.5	Unsigned32	read-only	If snPortMacSecurityIntfContentViolationType is shutdown(1), whether this interface has been shut down due to a security violation and the value gives the number of seconds before this interface is enabled again. If snPortMacSecurityIntfContentViolationType is restrict(2), this value will be always 0.
snPortMacSecurityIntfContentTable	1.3.6.1.4.1.1991.1.1.3.24.1.1.3		not-accessible	Port MAC security statistics on each Ethernet Interface.
U32 snPortMacSecurityIntfContentTotalMACs	1.3.6.1.4.1.1991.1.1.3.24.1.1.3.1.8	Unsigned32	read-only	The totol number of port MAC security MAC addresses are locked in this interface.
U32 snPortMacSecurityIntfContentViolationCounts	1.3.6.1.4.1.1991.1.1.3.24.1.1.3.1.9	Unsigned32	read-only	The totol number of counts of violation are collected in this interface.
INT snPortMacSecurityIntfContentViolationType	1.3.6.1.4.1.1991.1.1.3.24.1.1.3.1.3	INTEGER	read-write	Port security violation type for this interface is shutdown or restrict.
MAC snPortMacSecurityIntfMacAddress	1.3.6.1.4.1.1991.1.1.3.24.1.1.4.1.2	MacAddress	read-only	The secure MAC address for this local Ethernet interface on which the secure MAC Address is configured and/or learned. The maximum number of the secure MAC Addresses is restricted by the snPortMacSecurityIntfContentMaxLockedMacAllowed.
snPortMacSecurityIntfMacEntry	1.3.6.1.4.1.1991.1.1.3.24.1.1.4.1		not-accessible	An entry in the snPortMacSecurityIntfMacTable
I32 snPortMacSecurityIntfMacIfIndex	1.3.6.1.4.1.1991.1.1.3.24.1.1.4.1.1	Integer32	read-only	ifIndex value of the local Ethernet interface on which MAC security is configured.
INT snPortMacSecurityIntfMacRowStatus	1.3.6.1.4.1.1991.1.1.3.24.1.1.4.1.4	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
snPortMacSecurityIntfMacTable	1.3.6.1.4.1.1991.1.1.3.24.1.1.4		not-accessible	Status of port MAC security on the device's interfaces.
U32 snPortMacSecurityIntfMacVlanId	1.3.6.1.4.1.1991.1.1.3.24.1.1.4.1.3	Unsigned32	read-write	The vlan membership of this interface, zero means don't care.
MAC snPortMacSecurityMAC	1.3.6.1.4.1.1991.1.1.3.24.1.1.1.1.4	MacAddress	read-only	The secure MAC address for this interface.
snPortMacSecurityModuleStatEntry	1.3.6.1.4.1.1991.1.1.3.24.1.1.2.1		not-accessible	An entry in the snPortMacSecurityModuleStatTable
I32 snPortMacSecurityModuleStatSlotNum	1.3.6.1.4.1.1991.1.1.3.24.1.1.2.1.1	Integer32	read-only	The slot number of the port security device module.
snPortMacSecurityModuleStatTable	1.3.6.1.4.1.1991.1.1.3.24.1.1.2		not-accessible	Port MAC security statistics on each module.
U32 snPortMacSecurityModuleStatTotalMACs	1.3.6.1.4.1.1991.1.1.3.24.1.1.2.1.3	Unsigned32	read-only	The totol number of port MAC security MAC addresses are learned or configured in this module.
U32 snPortMacSecurityModuleStatTotalSecurityPorts	1.3.6.1.4.1.1991.1.1.3.24.1.1.2.1.2	Unsigned32	read-only	The totol number of Ethernet interfaces on which MAC security is configured in this module.
U32 snPortMacSecurityModuleStatTotalShutdownPorts	1.3.6.1.4.1.1991.1.1.3.24.1.1.2.1.5	Unsigned32	read-only	The totol number of Ethernet interfaces are shutted down due to security violation in this module.
U32 snPortMacSecurityModuleStatViolationCounts	1.3.6.1.4.1.1991.1.1.3.24.1.1.2.1.4	Unsigned32	read-only	The totol number of counts of violation are collected in this module.
U32 snPortMacSecurityQueryIndex	1.3.6.1.4.1.1991.1.1.3.24.1.1.1.1.3	Unsigned32	read-only	Entry index within the given resource of local Ethernet interface on which MAC security is configured.
INT snPortMacSecurityResource	1.3.6.1.4.1.1991.1.1.3.24.1.1.1.1.2	INTEGER	read-only	The MAC address was secured using local or shared resources.
INT snPortMacSecurityShutdownStatus	1.3.6.1.4.1.1991.1.1.3.24.1.1.1.1.6	INTEGER	read-only	Interface up/down status.
U32 snPortMacSecurityShutdownTimeLeft	1.3.6.1.4.1.1991.1.1.3.24.1.1.1.1.7	Unsigned32	read-only	If snPortMacSecurityShutdownStatus is up(1), this value will be 0. If snPortMacSecurityShutdownStatus is down(2), this gives the number of seconds before this interface is enabled again. In the later case, 0 means interface is permanently down.
snPortMacSecurityTable	1.3.6.1.4.1.1991.1.1.3.24.1.1.1		not-accessible	Status of port MAC security on the device's interfaces.
U32 snPortMacSecurityVlanId	1.3.6.1.4.1.1991.1.1.3.24.1.1.1.1.8	Unsigned32	read-only	The vlan membership of this interface.
snPortMonitor	1.3.6.1.4.1.1991.1.1.3.25
snPortMonitorEntry	1.3.6.1.4.1.1991.1.1.3.25.1.1		not-accessible	An entry in the snPortMonitorTable
NUM snPortMonitorIfIndex	1.3.6.1.4.1.1991.1.1.3.25.1.1.1	InterfaceIndex	not-accessible	ifIndex value of the local interface on which monitoring is configuerd.
STR snPortMonitorMirrorList	1.3.6.1.4.1.1991.1.1.3.25.1.1.2	DisplayString	read-write	Lists the monitoring configuration of this port. The value is a space delimited sequence of ifIndex of mirror port and monitor mode. The values for mode can be - 0 - off, 1 - input, 2 - output, 3 - both Eg. '65 2 66 1' means send the output traffic to port 2/1 and input traffic to port 2/2. To turn off a mirror use monitor mode of 0 (off) in the list.
snPortMonitorTable	1.3.6.1.4.1.1991.1.1.3.25.1		not-accessible	Status of port monitoring on the device's interfaces.
snPortStpEntry	1.3.6.1.4.1.1991.1.1.3.5.1.1		not-accessible	An entry in the snPortStpTable indicates the configuration on a specified port. A SNMP SET PDU for a row of the snPortStpTable requires the entired sequence of the MIB Objects in each snPortStpEntry stored in one PDU. Otherwise, GENERR return-value will be returned.
I32 snPortStpEntrySize	1.3.6.1.4.1.1991.1.1.3.1.24	Integer32	read-only	The size of each port stp table entry.
snPortStpInfo	1.3.6.1.4.1.1991.1.1.3.5
INT snPortStpOperState	1.3.6.1.4.1.1991.1.1.3.5.1.1.5	INTEGER	read-only	By default, this mode is set to notActivated(0). notActivated(0)...the Port STP entry is not activated and not in running mode. activated(1)......the Port STP entry is activated and in running mode
INT snPortStpPathCost	1.3.6.1.4.1.1991.1.1.3.5.1.1.4	INTEGER	read-write	dot1dStpPortPathCost : The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN. Writing value zero to this object sets path cost to a default value which automatically changes according to port speed. Reading value zero indicates an unknown path cost value because port speed cannot be determined due to speed auto sense in progress.
INT snPortStpPortAdminEdgePort	1.3.6.1.4.1.1991.1.1.3.5.1.1.15	INTEGER	read-write	The administrative value of the Edge Port parameter. A value of TRUE(1) indicates that this port should be assumed as an edge-port and a value of FALSE(2) indicates that this port should be assumed as a non-edge-port.
INT snPortStpPortAdminPointToPoint	1.3.6.1.4.1.1991.1.1.3.5.1.1.16	INTEGER	read-write	The administrative point-to-point status of the LAN segment attached to this port. A value of TRUE(1) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of FALSE(2) indicates that this port should be treated as having a shared media connection.
INT snPortStpPortAdminRstp	1.3.6.1.4.1.1991.1.1.3.5.1.1.13	INTEGER	read-write	Enable or disable RSTP of a port which is a member of a VLAN. If the VLAN is not operating in RSTP, this object will return FALSE(2) and this object is not writable.
BRI snPortStpPortDesignatedBridge	1.3.6.1.4.1.1991.1.1.3.5.1.1.11	BridgeId	read-only	The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
I32 snPortStpPortDesignatedCost	1.3.6.1.4.1.1991.1.1.3.5.1.1.9	Integer32	read-only	The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OCT snPortStpPortDesignatedPort	1.3.6.1.4.1.1991.1.1.3.5.1.1.12	OCTET STRING	read-only	The Port Identifier of the port on the Designated Bridge for this port's segment.
BRI snPortStpPortDesignatedRoot	1.3.6.1.4.1.1991.1.1.3.5.1.1.10	BridgeId	read-only	The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
INT snPortStpPortEnable	1.3.6.1.4.1.1991.1.1.3.5.1.1.6	INTEGER	not-accessible	The enabled/disabled status of the port.
C32 snPortStpPortForwardTransitions	1.3.6.1.4.1.1991.1.1.3.5.1.1.7	Counter32	not-accessible	The number of times this port has transitioned from the Learning state to the Forwarding state.
I32 snPortStpPortNum	1.3.6.1.4.1.1991.1.1.3.5.1.1.2	Integer32	read-only	The port number of the Switch. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only).
INT snPortStpPortPriority	1.3.6.1.4.1.1991.1.1.3.5.1.1.3	INTEGER	read-write	The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of dot1dStpPort.
INT snPortStpPortProtocolMigration	1.3.6.1.4.1.1991.1.1.3.5.1.1.14	INTEGER	read-write	When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read.
INT snPortStpPortState	1.3.6.1.4.1.1991.1.1.3.5.1.1.8	INTEGER	read-only	The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpPortEnable), this object will have a value of disabled(1).
I32 snPortStpSetAll	1.3.6.1.4.1.1991.1.1.3.1.11	Integer32	read-write	The value of this object is 1 which means invoking Port STP Set-all command. The snPortStpPriority, snPortStpPathCost, the read-write STP related attributes of the first row of table will be used to set the same attributes for all the ports in the system. Note: prior setting this object, all the intended attributes of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire port-table. The previous setting will be overwritten by the new one.
snPortStpTable	1.3.6.1.4.1.1991.1.1.3.5.1		not-accessible	A specific snPortStpTable consists of a number of switch ports. This table only exists if only if snVLanByPortCfgTable exists and snVLanByPortCfgStpMode is enabled for each VLAN.
INT snPortStpVLanId	1.3.6.1.4.1.1991.1.1.3.5.1.1.1	INTEGER	read-only	The VLAN ID of the VLAN switch community.
snPosInterface	1.3.6.1.4.1.1991.1.1.3.3.2.2
snPvcInterface	1.3.6.1.4.1.1991.1.1.3.3.2.9
snQos	1.3.6.1.4.1.1991.1.1.3.14
snQosBindEntry	1.3.6.1.4.1.1991.1.1.3.14.2.1		not-accessible	An entry of the snQosBindTable.
INT snQosBindIndex	1.3.6.1.4.1.1991.1.1.3.14.2.1.1	INTEGER	read-only	The table index of QOS Bind.
I32 snQosBindPriority	1.3.6.1.4.1.1991.1.1.3.14.2.1.2	Integer32	read-only	QOS bind priority.
INT snQosBindProfileIndex	1.3.6.1.4.1.1991.1.1.3.14.2.1.3	INTEGER	read-write	QOS Bind Profile Index. This is pointer to the index of snQosProfile Table.
snQosBindTable	1.3.6.1.4.1.1991.1.1.3.14.2		not-accessible	A table contains the configuration of 802.1p to qos profile binding groups.
INT snQosProfileCalculatedBandwidth	1.3.6.1.4.1.1991.1.1.3.14.1.1.4	INTEGER	read-only	Qos Profile Calculated Bandwidth.
snQosProfileEntry	1.3.6.1.4.1.1991.1.1.3.14.1.1		not-accessible	An entry of the snQosProfileTable.
INT snQosProfileIndex	1.3.6.1.4.1.1991.1.1.3.14.1.1.1	INTEGER	read-only	The table index of QOS Profile.
STR snQosProfileName	1.3.6.1.4.1.1991.1.1.3.14.1.1.2	DisplayString	read-write	Qos Profile Name string.
INT snQosProfileRequestedBandwidth	1.3.6.1.4.1.1991.1.1.3.14.1.1.3	INTEGER	read-write	Qos Profile Requested Bandwidth.
snQosProfileTable	1.3.6.1.4.1.1991.1.1.3.14.1		not-accessible	A table contains the configuration of qos profile groups.
snRadius	1.3.6.1.4.1.1991.1.1.3.12
INT snRadiusDeadTime	1.3.6.1.4.1.1991.1.1.3.12.1.5	INTEGER	read-write	Interval specifies Radius server dead time, each unit is one minute.
OCT snRadiusEnableMethod	1.3.6.1.4.1.1991.1.1.3.12.1.8	OCTET STRING	read-write	A sequence of authentication methods. Each octet represents a method to authenticate the user entering priviledge mode of the command line interface. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods.
INT snRadiusEnableTelnetAuth	1.3.6.1.4.1.1991.1.1.3.12.1.2	INTEGER	read-write	Enable/Disable telnet authentication specified by 'snRadiusLoginMethod'.
snRadiusGeneral	1.3.6.1.4.1.1991.1.1.3.12.1
STR snRadiusKey	1.3.6.1.4.1.1991.1.1.3.12.1.6	DisplayString	read-write	Authentication key displayed as encrypted text. Write operation can only be done if the SET request uses SNMPv3 with data encrypted using privacy key. FastIron and NetIron platforms support keysize upto 64 characters.
OCT snRadiusLoginMethod	1.3.6.1.4.1.1991.1.1.3.12.1.7	OCTET STRING	read-write	A sequence of authentication methods. Each octet represents a method to authenticate the user login process. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods.
INT snRadiusRetransmit	1.3.6.1.4.1.1991.1.1.3.12.1.3	INTEGER	read-write	The number of authentication query retransmissions to the Radius server.
I32 snRadiusServerAcctPort	1.3.6.1.4.1.1991.1.1.3.12.2.1.3	Integer32	read-write	Account UDP port number.
I32 snRadiusServerAuthPort	1.3.6.1.4.1.1991.1.1.3.12.2.1.2	Integer32	read-write	Authentication UDP port number.
snRadiusServerEntry	1.3.6.1.4.1.1991.1.1.3.12.2.1		not-accessible	An entry in the Radius server table.
IP snRadiusServerIp	1.3.6.1.4.1.1991.1.1.3.12.2.1.1	IpAddress	read-only	Radius server IP address.
STR snRadiusServerRowKey	1.3.6.1.4.1.1991.1.1.3.12.2.1.5	DisplayString	read-write	Authentication key displayed as encrypted text. FastIron and NetIron platforms support keysize upto 64 characters.
INT snRadiusServerRowStatus	1.3.6.1.4.1.1991.1.1.3.12.2.1.4	INTEGER	read-write	To create or delete a Radius server table entry.
snRadiusServerTable	1.3.6.1.4.1.1991.1.1.3.12.2		not-accessible	Radius server table.
INT snRadiusServerUsage	1.3.6.1.4.1.1991.1.1.3.12.2.1.6	INTEGER	read-write	To allow this server to be dedicated for a particular AAA activity.
INT snRadiusSNMPAccess	1.3.6.1.4.1.1991.1.1.3.12.1.1	INTEGER	read-only	Indicate whether RADIUS server and key related MIB objects can be accessed by SNMP manager. If value is disabled, then snRadiusKey and snRadiusServerTable objects will not be accessible.
OCT snRadiusSNMPServerMethod	1.3.6.1.4.1.1991.1.1.3.12.1.10	OCTET STRING	read-write	A sequence of authentication methods. Each octet represents a method to authenticate the user accessing the snmp-server. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods.
INT snRadiusTimeOut	1.3.6.1.4.1.1991.1.1.3.12.1.4	INTEGER	read-write	Interval specifies how long to wait for authentication reply from the Radius server, each unit is one second.
OCT snRadiusWebServerMethod	1.3.6.1.4.1.1991.1.1.3.12.1.9	OCTET STRING	read-write	A sequence of authentication methods. Each octet represents a method to authenticate the user accessing the web-server. Each octet has the following enumeration value: enable(1) - authenticate by command line interface enable password radius(2) - authenticate by requesting radius server local(3) - authenticate by local user account table line(4) - authenticate by telnet password tacplus(5) - authenticate by requesting tacplus server none(6) - do not authenticate tacacs(7) - authenticate by requesting tacacs server Setting a zero length octet string invalidates all previous authentication methods.
snSFlow	1.3.6.1.4.1.1991.1.1.3.19
snSflowCollectorEntry	1.3.6.1.4.1.1991.1.1.3.19.2.1		not-accessible	A row in the sFlow collector table.
I32 snSflowCollectorIndex	1.3.6.1.4.1.1991.1.1.3.19.2.1.1	Integer32	read-only	The index to the sFlow collector table.
IP snSflowCollectorIP	1.3.6.1.4.1.1991.1.1.3.19.2.1.2	IpAddress	read-write	The sFlow collector ip address.
INT snSflowCollectorRowStatus	1.3.6.1.4.1.1991.1.1.3.19.2.1.4	INTEGER	read-write	To create, update or delete a SFlow collector table entry. If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
snSflowCollectorTable	1.3.6.1.4.1.1991.1.1.3.19.2		not-accessible	Table of all but first sFlow collectors. The first collector can be configured using sFlowTable in RFC 3176. The RFC cannot be used to configure more than one sFlow collectors. This table has been created to fill this gap.
I32 snSflowCollectorUDPPort	1.3.6.1.4.1.1991.1.1.3.19.2.1.3	Integer32	read-write	The sFlow collector UDP port number.
snSFlowGlb	1.3.6.1.4.1.1991.1.1.3.19.1
snSSH	1.3.6.1.4.1.1991.1.1.3.26
snSSL	1.3.6.1.4.1.1991.1.1.3.27
snStacking	1.3.6.1.4.1.1991.1.1.3.31
snSubInterface	1.3.6.1.4.1.1991.1.1.3.3.2.7
INT snSw8021qTagMode	1.3.6.1.4.1.1991.1.1.3.1.13	INTEGER	read-write	The Switch Group is configured with the IEEE802.1q Tagging mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate IEEE802.1q Tagging mode. disabled(0)..........no IEEE802.1q Tagging.
I32 snSw8021qTagType	1.3.6.1.4.1.1991.1.1.3.1.34	Integer32	read-write	The IEEE802.1q tag type embedded in the length/type field of an Ethernet packet. It specifies that the 2 octets after the length/type field in an Ethernet packet is the tag value.
I32 snSwBroadcastLimit	1.3.6.1.4.1.1991.1.1.3.1.35	Integer32	read-write	Limit the number of broadcast packets to forward out of the switch ports. This object specifies the number of broadcast packets per second. Setting a value of 0 to this object disables the limitation check. This object is deprecated by snSwBroadcastLimit2 on NI platform.
U32 snSwBroadcastLimit2	1.3.6.1.4.1.1991.1.1.3.1.45	Unsigned32	read-write	Limit the number of broadcast packets to forward out of the switch ports. This object specifies the number of broadcast packets per second.
INT snSwClearCounters	1.3.6.1.4.1.1991.1.1.3.1.33	INTEGER	read-write	valid(0) - a SNMP-GET of this mib shows that it is valid command to use. clear(1) - represents clear counter command of the following counters: Dot3, MIB2, IP and IPX counters for all ports.
INT snSwDefaultVLanId	1.3.6.1.4.1.1991.1.1.3.1.38	INTEGER	read-write	The VLAN ID of the DEFAULT PORT-VLAN.
INT snSwEnableBridgeNewRootTrap	1.3.6.1.4.1.1991.1.1.3.1.25	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate bridge new root traps.
INT snSwEnableBridgeTopoChangeTrap	1.3.6.1.4.1.1991.1.1.3.1.26	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate bridge topology change traps.
INT snSwEnableLockedAddrViolationTrap	1.3.6.1.4.1.1991.1.1.3.1.27	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate locked address violation traps.
I32 snSwEosBufferSize	1.3.6.1.4.1.1991.1.1.3.1.20	Integer32	read-only	A specific buffer size for all the different EOS buffers.
INT snSwFastStpMode	1.3.6.1.4.1.1991.1.1.3.1.42	INTEGER	read-write	Fast Spanning Tree System Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Fast Spanning Tree disabled(0)..........no Fast Spanning Tree
INT snSwGlobalAutoNegotiate	1.3.6.1.4.1.1991.1.1.3.1.39	INTEGER	read-write	This feature only applies to Gigabit Ethernet ports. If set to disable(0), all Gigabit Ethernet ports will be put to non- negotiation mode. If set to enable(1), all Gigabit Ethernet ports will start auto-negotiation indefinitely until succeed. If set to negFullAuto(2), all Gigabit Ethernet ports will start with auto-negotiation, if the negotiation failed, then they will automatically switch to non-negotiation mode. Stackable products (except TurboIron 8) Gigabit Ethernet ports do not support negFullAuto(2). If the snSwPortInfoAutoNegotiate value of a port was not set to global, this global value does not apply to the negotiation mode of that port.
INT snSwGlobalStpMode	1.3.6.1.4.1.1991.1.1.3.1.14	INTEGER	read-write	Spanning Tree System Global Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Spanning Tree disabled(0)..........no Spanning Tree
INT snSwGroupDefaultCfgMode	1.3.6.1.4.1.1991.1.1.3.1.4	INTEGER	read-write	The Switch Group is configured with the Default configuration. If the default configuration gets overwritten, the state will change to non-default. default(1)...........default configuration nonDefault(2)..........non default configuration
INT snSwGroupIpL3SwMode	1.3.6.1.4.1.1991.1.1.3.1.2	INTEGER	read-write	The Switch Group is configured with the Layer3 IP Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate Layer3 IP Switch disabled(0)..........disable Layer3 IP Switch
INT snSwGroupIpMcastMode	1.3.6.1.4.1.1991.1.1.3.1.3	INTEGER	read-write	The Switch Group is configured with the IP Multicast pruning mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate IP Multicast pruning disabled(0)..........no IP Multicast pruning
INT snSwGroupOperMode	1.3.6.1.4.1.1991.1.1.3.1.1	INTEGER	read-write	noVLan(1) represents all switch ports with no virtual LAN by port (no Port VLAN), and with no tag assigned. vlanByPort(2) represents all switch ports with Basic VLAN (layer2 Switch).
I32 snSwGroupSwitchAgeTime	1.3.6.1.4.1.1991.1.1.3.1.5	Integer32	read-write	For FastIron: Sets the aging period for ports on the device, defining how long a port address remains active in the address table. Valid values: 0 = no aging, or 67 - 65535 seconds Default: 300 seconds. For NetIron: The Switch Age time is 180sec by default. The configured range is 10 to 10,000sec. The time represents the time span to age out an MAC Address entry.
STR snSwIfDescr	1.3.6.1.4.1.1991.1.1.3.3.5.1.18	DisplayString	read-only	A textual string containing the slot/port information about the interface.
INT snSwIfDhcpGateListId	1.3.6.1.4.1.1991.1.1.3.3.5.1.16	INTEGER	read-write	The ID for a DHCP gateway list entry relative to this switch port. 0 = unset or no assigned ID
INT snSwIfFastSpanPortEnable	1.3.6.1.4.1.1991.1.1.3.3.5.1.22	INTEGER	read-write	The enabled/disabled fast span port status of the port.
INT snSwIfFastSpanUplinkEnable	1.3.6.1.4.1.1991.1.1.3.3.5.1.23	INTEGER	read-write	The enabled/disabled fast span uplink status of the port.
INT snSwIfGBICStatus	1.3.6.1.4.1.1991.1.1.3.3.5.1.27	INTEGER	read-only	Indicate if the gig port has GBICs on them. If set to GBIC(1), it means that the port is GBIC. If set to miniGBIC(2), it means that the port miniGBIC. If set to empty(3), it means that the GBIC is missing. Value other(4) means that the port not a removable gig port.
INT snSwIfInfoAdminStatus	1.3.6.1.4.1.1991.1.1.3.3.5.1.10	INTEGER	read-write	The desired state of all ports. The testing(3) state indicates that no operational packets can be passed. (same as ifAdminStatus in MIB-II)
T/F snSwIfInfoAllowAllVlan	1.3.6.1.4.1.1991.1.1.3.3.5.1.61	TruthValue	read-write	Specifies allowing all vlan packets for pbr
INT snSwIfInfoAutoNegotiate	1.3.6.1.4.1.1991.1.1.3.3.5.1.19	INTEGER	read-write	This feature only applies to Gigabit Ethernet ports. If set to disable(0), port will be put to non-negotiation mode. If set to enable(1), port will start auto-negotiation indefinitely until succeed. If set to negFullAuto(2), the port will start with auto- negotiation, if the negotiation failed, then it will automatically switch to non-negotiation mode. Stackable products (except TurboIron 8) Gigabit Ethernet ports do not support negFullAuto(2). If set to global(3), port negotiation mode follows the value of snSwGlobalAutoNegotiate. Non-Gigabit Ethernet port returns the value other(4).
INT snSwIfInfoChnMode	1.3.6.1.4.1.1991.1.1.3.3.5.1.6	INTEGER	read-write	The port can be configured to operate in either half or full duplex mode. The values are: none(0) is not used. halfDuplex(1)...half duplex mode fullDuplex(2)...full duplex mode The read-back channel status from hardware are: halfDuplex(1)...half duplex mode fullDuplex(2)...full duplex mode The port media type (expansion or regular) and port link type (trunk or feeder) determine value of this object. The port can not set to half duplex mode if the port connect mode is m200e(4). However, the value of this parameter may be automatically set whenever the expansion port is connected (e.g. cascade connecting device).
INT snSwIfInfoConnectorType	1.3.6.1.4.1.1991.1.1.3.3.5.1.9	INTEGER	read-only	The type of connector that the port offers. The values are: other(1)...........other or unknown connector copper(2)..........Copper connector fiber(3)...........Fiber connector both(4)............Supports both Copper and Fiber This describes the physical connector type
snSwIfInfoEntry	1.3.6.1.4.1.1991.1.1.3.3.5.1		not-accessible	An entry in the snSwIfInfo table indicates the configuration on a specified port. A SNMP SET PDU for a row of the snSwIfInfoTable requires the entire sequence of the MIB Objects in each snSwIfInfoEntry stored in one PDU. Otherwise, GENERR return-value will be returned.
INT snSwIfInfoFlowControl	1.3.6.1.4.1.1991.1.1.3.3.5.1.20	INTEGER	read-write	Enable/Disbale port flow control.
INT snSwIfInfoGigType	1.3.6.1.4.1.1991.1.1.3.3.5.1.21	INTEGER	read-only	The media type for the port. The values are: m1000BaseSX(0)....1Gbits per second fiber, with a short wavelength transceiver. m1000BaseLX(1)....1Gbits per second fiber, with a long wavelength transceiver (3km). m1000BaseLH(2)....1Gbits per second fiber, with a special wavelength transceiver (50km). m1000BaseLHA(3)....1Gbits per second fiber, with a special wavelength transceiver (70km). m1000BaseLHB(4)....1Gbits per second fiber, with a special wavelength transceiver (150km). m1000BaseTX(5)....1Gbits per second copper (100meter). m10000BaseSR(6)....10Gbits per second fiber, with a short range wavelength transceiver (100m). m10000BaseLR(7)....10Gbits per second fiber, with a long range wavelength transceiver (10km). m10000BaseER(8)....10Gbits per second fiber, with a extended range wavelength transceiver (40km). sfpCWDM1470nm80Km(9)....1Gbits per second CWDM fiber, with a wavelength 1470nm, reach 80 kms. sfpCWDM1490nm80Km(10)....1Gbits per second CWDM fiber, with a wavelength 1490nm, reach 80 kms. sfpCWDM1510nm80Km(11)....1Gbits per second CWDM fiber, with a wavelength 1510nm, reach 80 kms. sfpCWDM1530nm80Km(12)....1Gbits per second CWDM fiber, with a wavelength 1530nm, reach 80 kms. sfpCWDM1550nm80Km(13)....1Gbits per second CWDM fiber, with a wavelength 1550nm, reach 80 kms. sfpCWDM1570nm80Km(14)....1Gbits per second CWDM fiber, with a wavelength 1570nm, reach 80 kms. sfpCWDM1590nm80Km(15)....1Gbits per second CWDM fiber, with a wavelength 1590nm, reach 80 kms. sfpCWDM1610nm80Km(16)....1Gbits per second CWDM fiber, with a wavelength 1610nm, reach 80 kms. sfpCWDM1470nm100Km(17)....1Gbits per second CWDM fiber, with a wavelength 1470nm, reach 100 kms. sfpCWDM1490nm100Km(18)....1Gbits per second CWDM fiber, with a wavelength 1490nm, reach 100 kms. sfpCWDM1510nm100Km(19)....1Gbits per second CWDM fiber, with a wavelength 1510nm, reach 100 kms. sfpCWDM1530nm100Km(20)....1Gbits per second CWDM fiber, with a wavelength 1530nm, reach 100 kms. sfpCWDM1550nm100Km(21)....1Gbits per second CWDM fiber, with a wavelength 1550nm, reach 100 kms. sfpCWDM1570nm100Km(22)....1Gbits per second CWDM fiber, with a wavelength 1570nm, reach 100 kms. sfpCWDM1590nm100Km(23)....1Gbits per second CWDM fiber, with a wavelength 1590nm, reach 100 kms. sfpCWDM1610nm100Km(24)....1Gbits per second CWDM fiber, with a wavelength 1610nm, reach 100 kms. m1000BaseLHX(25)...1Gbits per second fiber, with a special wavelength transceiver (150km). m1000BaseLMC(35)...Link Media Copper. mXFP10000BaseSR(36)...10GBASE fiber, 850nm serial pluggable XFP optic (LC), target range 300m over MMF. mXFP10000BaseLR(37)...10GBASE fiber, 1310nm serial pluggable XFP optic (LC) for up to 10km over SMF. mXFP10000BaseER(38)...10GBASE fiber, 1550nm serial pluggable XFP optic (LC) for up to 40km over SMF. mXFP10000BaseSW(39)...not used. mXFP10000BaseLW(40)...not used. mXFP10000BaseEW(41)...not used mXFP10000BaseCX4(42)...10GBASE-CX4, XFP module,15m, CX4 connector. mXFP10000BaseZR(43)...1550nm serial pluggable XFP optic (LC) for up to 80km over SMF. mXFP10000BaseZRD(44)...10GBASE-ZR DWDM, XFP optic, 80km. mXFP10000BaseSRSW(46)...same as .mXFP10000BaseSR(36) mXFP10000BaseLRLW(47)...same as .mXFP10000BaseLR(37) mXFP10000BaseEREW(48)...same as mXFP10000BaseER(38). m10000BaseT(49)...10GBASE fiber. m2500BaseTX(50)...2.5GBASE fiber. mCFP100GBaseSR10(145)... 100GbE CFP optic (MPO 2x12), SR10, for distances up to 100m over MMF. mCFP100GBaseLR4(146)... 100GbE CFP optic (SC), LR4, for distances up to 10 km over SMF. mCFP100GBaseER4(147)... 100GbE CFP optic, ER4, for distances up to 40 km over SMF. mCFP100GBase10x10g2Km(148)... 100GbE CFP optic (LC), 10x10, for distances up to 2 km over SMF. mCFP100GBase10x10g10Km(149)... 100GbE CFP optic (LC), 10x10, for distances up to 10 km over SMF. mXFP10000BaseUSR(152)... 10 Gbps Ultra-Short Range (USR) 100m Ethernet optical transceiver. mXFP10000BaseTwinax(153)... 10Gbps Active copper twinax cables. mCFP2-100GBaseSR10(154)... 100GbE CFP2 optic (MPO 2x12), SR10, for distances up to 100m over MMF. mCFP2-100GBaseLR4(155)... 100GbE CFP2 optic (SC), LR4, for distances up to 10 km over SMF. mCFP2-100GBaseER4(156)... 100GbE CFP2 optic, ER4, for distances up to 40 km over SMF. mCFP2-100GBase10x10g2Km(157)... 100GbE CFP2 optic (LC), 10x10, for distances up to 2 km over SMF. mCFP2-100GBase10x10g10Km(158)... 100GbE CFP2 optic (LC), 10x10, for distances up to 10 km over SMF. notApplicable(255)....a non-gigabit port.
INT snSwIfInfoL2FowardEnable	1.3.6.1.4.1.1991.1.1.3.3.5.1.60	INTEGER	read-write	The status of cluster L2 forward feature on an ethernet port. When this object is set to disable, the STP protocol packets coming on the MCT VLANs are dropped. The snSwIfInfoL2FowardEnable has more preference than brcdMctL2Forward for this interface when set with enable(1) or disable(2). When set to globalConfig(3) the status of brcdMctL2Forward object applies for this interface.
INT snSwIfInfoLinkStatus	1.3.6.1.4.1.1991.1.1.3.3.5.1.11	INTEGER	read-only	The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. (same as ifOperStatus in MIB-II)
INT snSwIfInfoMediaType	1.3.6.1.4.1.1991.1.1.3.3.5.1.8	INTEGER	read-only	The media type for the port. The values are: other(1).........other or unknown media. m100BaseTX(2)....100Mbits per second copper. m100BaseFX(3)....100Mbits per second fiber. m1000BaseFX(4)...1Gbits per second fiber. mT3(5)...........45Mbits per second (T3). m155ATM(6).......155Mbits per second (ATM). m1000BaseTX(7)...1Gbits per second copper. m622ATM(8).......622Mbits per second (ATM). m155POS(9).......155Mbits per second (POS). m622POS(10)......622Mbits per second (POS). m2488POS(11).....2488Mbits per second (POS). m10000BaseFX(12).10Gbits per second fiber. m9953POS(13).....9953Mbits per second (POS). m16GStacking(14)...16Gbits per second fiber. m40GStacking(16). 40Gbits per second fiber. m40GBaseFX(17)....40Gbits per second fiber. m10000BaseTX(18)..10Gbits per second copper. m2500BaseTX(19). 2.5Gbits per second fiber.
INT snSwIfInfoMirrorMode	1.3.6.1.4.1.1991.1.1.3.3.5.1.58	INTEGER	read-write	Enable/disable mirror on this port.
OCT snSwIfInfoMirrorPorts	1.3.6.1.4.1.1991.1.1.3.3.5.1.3	OCTET STRING	read-write	The list of port/interface index (ifindex), which mirror this interface, when monitoring is enabled.
INT snSwIfInfoMonitorMode	1.3.6.1.4.1.1991.1.1.3.3.5.1.2	INTEGER	read-write	For FastIron platforms, this object is DEPRECATED by snSwIf2MirrorMode and snPortMonitorTable. For NetIron platforms, this object is DEPRECATED by snPortMonitorTable.
PHY snSwIfInfoNativeMacAddress	1.3.6.1.4.1.1991.1.1.3.3.5.1.62	PhysAddress	read-only	The port native MAC address. The native MAC address represents the switch port.
PHY snSwIfInfoPhysAddress	1.3.6.1.4.1.1991.1.1.3.3.5.1.13	PhysAddress	read-only	The port physical address. The physical address represents the switch port.
NUM snSwIfInfoPortNum	1.3.6.1.4.1.1991.1.1.3.3.5.1.1	InterfaceIndex	read-only	The port/interface index (ifindex).
INT snSwIfInfoPortQos	1.3.6.1.4.1.1991.1.1.3.3.5.1.12	INTEGER	read-write	The Stand alone stackable switch Port Qos Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron Port Qos Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
INT snSwIfInfoSpeed	1.3.6.1.4.1.1991.1.1.3.3.5.1.7	INTEGER	read-write	The speed configuration for a port. The values are: none(0)..........not used. sAutoSense(1)....Auto-sensing 10 or 100Mbits. s10M(2)..........10Mbits per second. s100M(3).........100Mbits per second. s1G(4)...........1Gbits per second. s1GM(5)..........1Gbits per second master. s155M(6).........155Mbits per second (ATM) (for expansion board only). s10G(7)..........10Gbits per second. s622M(8).........OC12 - 622Mbits per second s2488M(9)........OC48 - 2.488Gbits per second s9953M(10).......OC192 - 9.953Gbits per second s16G(11)..........16Gbits per second. s40G(13)..........40Gbits per second. s2500M(14)..........2.5Gbits per second. The read-back hardware status are the following: none(0)..........link down or no traffic. s10M(2)..........10Mbits per second. s100M(3).........100Mbits per second. s1G(4)...........1Gbits per second. s1GM(5)..........1Gbits per second master. s155M(6).........155Mbits per second (ATM) (for expansion board only). s10G(7)..........10Gbits per second. s622M(8).........OC12 - 622Mbits per second s2488M(9)........OC48 - 2.488Gbits per second s9953M(10).......OC192 - 9.953Gbits per second s16G(11)..........16Gbits per second. s40G(13)..........40Gbits per second. s2500M(14)..........2.5Gbits per second. The port media type (expansion or regular) and port link type (trunk or feeder) determine whether this object can be written and the valid values. It is not allowed to change speed for trunks ports. For expansion ports, all of the above speed can be set. However, the value of this parameter may be automatically set whenever the expansion port is connected (e.g. cascade connecting device).
snSwIfInfoTable	1.3.6.1.4.1.1991.1.1.3.3.5		not-accessible	A specific snSwIfInfo group consists of a number of switch ports.
INT snSwIfInfoTagMode	1.3.6.1.4.1.1991.1.1.3.3.5.1.4	INTEGER	read-write	For tagged/dual port, we could have multiple VLANs per port. For untagged port, there is only one VLAN ID per port, dual mode is associated with a vlan id 'snSwIfVlanId', dual mode with snSwIfVlanId zero disables the dual mode.
I32 snSwIfInfoTagType	1.3.6.1.4.1.1991.1.1.3.3.5.1.5	Integer32	read-write	The IEEE802.1q tag type embedded in the length/type field of an Ethernet packet. It specifies that the 2 octets after the length/type field in an Ethernet packet is the tag value.
C64 snSwIfInOctets	1.3.6.1.4.1.1991.1.1.3.3.5.1.46	Counter64	read-only	The total number of octets received on the interface, including framing characters. This object is a 64-bit counter of the ifInOctets object, defined in RFC 1213. The octet string is in big-endian byte order.
INT snSwIfLoadInterval	1.3.6.1.4.1.1991.1.1.3.3.5.1.28	INTEGER	read-write	The time in seconds for which average port utilization should be carried out. The value should be incremental of 30 seconds, between the ranges specified.
INT snSwIfLockAddressCount	1.3.6.1.4.1.1991.1.1.3.3.5.1.14	INTEGER	read-write	The number of source MAC addresses are allowed for a port. Writing 0 to this object will allow any number of addresses.
T/F snSwIfMacLearningDisable	1.3.6.1.4.1.1991.1.1.3.3.5.1.59	TruthValue	read-write	The status of MAC learning feature on an ethernet port. For POS port, Get operation will return the default value and Set operation will return an error.
STR snSwIfName	1.3.6.1.4.1.1991.1.1.3.3.5.1.17	DisplayString	read-write	Port Name string.
C64 snSwIfOutOctets	1.3.6.1.4.1.1991.1.1.3.3.5.1.47	Counter64	read-only	The total number of octets transmitted out of the interface, including framing characters. This object is a 64-bit counter of the ifOutOctets object, defined in RFC 1213. The octet string is in big-endian byte order.
INT snSwIfPresent	1.3.6.1.4.1.1991.1.1.3.3.5.1.26	INTEGER	read-only	Indicate if the port is absent or present. This object only valid for M4 module.
INT snSwIfRouteOnly	1.3.6.1.4.1.1991.1.1.3.3.5.1.25	INTEGER	read-write	Enable/Disable L2 switching of a routing switch port. By default, the routing switch performs routing first. If routing failed, it performs switching. Enable route only instrcuts the routing switch to perform routing only. For a L2 switching only product, reading this object always return 'disabled', writing 'enabled' to this object takes no effect.
C32 snSwIfStatsAlignErrors	1.3.6.1.4.1.1991.1.1.3.3.5.1.31	Counter32	read-only	dot3StatsAlignmentErrors : A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
C32 snSwIfStatsFCSErrors	1.3.6.1.4.1.1991.1.1.3.3.5.1.32	Counter32	read-only	dot3StatsFCSErrors : A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
C32 snSwIfStatsFrameTooLongs	1.3.6.1.4.1.1991.1.1.3.3.5.1.36	Counter32	read-only	dot3StatsFrameTooLongs : A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
C32 snSwIfStatsFrameTooShorts	1.3.6.1.4.1.1991.1.1.3.3.5.1.37	Counter32	read-only	A count of frames received on a particular interface that below the minimum permitted frame size.
C32 snSwIfStatsInBcastFrames	1.3.6.1.4.1.1991.1.1.3.3.5.1.38	Counter32	read-only	The total number of broadcast packets received on the interface.
G32 snSwIfStatsInBitsPerSec	1.3.6.1.4.1.1991.1.1.3.3.5.1.48	Gauge32	read-only	The number of bits per second received on the interface over a 5 minutes interval.
C32 snSwIfStatsInDiscard	1.3.6.1.4.1.1991.1.1.3.3.5.1.42	Counter32	read-only	The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
C32 snSwIfStatsInFrames	1.3.6.1.4.1.1991.1.1.3.3.5.1.29	Counter32	read-only	The total number of packets received on the interface.
C64 snSwIfStatsInJumboFrames	1.3.6.1.4.1.1991.1.1.3.3.5.1.56	Counter64	read-only	The total number of jumbo packets received on the interface.
U32 snSwIfStatsInKiloBitsPerSec	1.3.6.1.4.1.1991.1.1.3.3.5.1.54	Unsigned32	read-only	Bit rate in kilobits per second received on the 10G and faster interface over a 5 minutes interval.
C32 snSwIfStatsInMcastFrames	1.3.6.1.4.1.1991.1.1.3.3.5.1.40	Counter32	read-only	The total number of multicast packets received on the interface.
G32 snSwIfStatsInPktsPerSec	1.3.6.1.4.1.1991.1.1.3.3.5.1.50	Gauge32	read-only	The number of packets per second received on the interface over a 5 minutes interval.
INT snSwIfStatsInUtilizationEx	1.3.6.1.4.1.1991.1.1.3.3.5.1.52	INTEGER	read-only	The input network utilization in hundredths of a percent over a 5 minutes interval.
C32 snSwIfStatsLinkChange	1.3.6.1.4.1.1991.1.1.3.3.5.1.45	Counter32	read-only	The total number of link state change of the interface.
I32 snSwIfStatsMacStations	1.3.6.1.4.1.1991.1.1.3.3.5.1.44	Integer32	read-only	The total number of MAC Stations connected to the interface.
C32 snSwIfStatsMultiColliFrames	1.3.6.1.4.1.1991.1.1.3.3.5.1.33	Counter32	read-only	dot3StatsMultipleCollisionFrames : A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object.
C32 snSwIfStatsOutBcastFrames	1.3.6.1.4.1.1991.1.1.3.3.5.1.39	Counter32	read-only	The total number of broadcast packets transmitted out of the interface.
G32 snSwIfStatsOutBitsPerSec	1.3.6.1.4.1.1991.1.1.3.3.5.1.49	Gauge32	read-only	The number of bits per second transmitted out of the interface over a 5 minutes interval.
C32 snSwIfStatsOutDiscard	1.3.6.1.4.1.1991.1.1.3.3.5.1.43	Counter32	read-only	The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
C32 snSwIfStatsOutFrames	1.3.6.1.4.1.1991.1.1.3.3.5.1.30	Counter32	read-only	The total number of packets transmitted out of the interface.
C64 snSwIfStatsOutJumboFrames	1.3.6.1.4.1.1991.1.1.3.3.5.1.57	Counter64	read-only	The total number of jumbo packets transmitted out of the interface.
U32 snSwIfStatsOutKiloBitsPerSec	1.3.6.1.4.1.1991.1.1.3.3.5.1.55	Unsigned32	read-only	Bit rate in kilobits per second transmitted out of the 10G and faster interface over a 5 minutes interval.
C32 snSwIfStatsOutMcastFrames	1.3.6.1.4.1.1991.1.1.3.3.5.1.41	Counter32	read-only	The total number of multicast packets transmitted out of the interface.
G32 snSwIfStatsOutPktsPerSec	1.3.6.1.4.1.1991.1.1.3.3.5.1.51	Gauge32	read-only	The number of packets per second transmitted out of the interface over a 5 minutes interval.
INT snSwIfStatsOutUtilization	1.3.6.1.4.1.1991.1.1.3.3.5.1.53	INTEGER	read-only	The output network utilization in hundredths of a percent over a 5 minutes interval.
C32 snSwIfStatsRxColliFrames	1.3.6.1.4.1.1991.1.1.3.3.5.1.35	Counter32	read-only	A count of successfully received frames on a particular interface for which transmission is inhibited by more than one collision. This object is not specified in dot3 but it has the same functionarity as snSwIfStatsTxColliFrames.
C32 snSwIfStatsTxColliFrames	1.3.6.1.4.1.1991.1.1.3.3.5.1.34	Counter32	read-only	A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by a combination of both dot3StatsSingleCollisionFrames and dot3StatsMultipleCollisionFrames objects.
INT snSwIfStpPortEnable	1.3.6.1.4.1.1991.1.1.3.3.5.1.15	INTEGER	read-write	The enabled/disabled status of the port.
INT snSwIfVlanId	1.3.6.1.4.1.1991.1.1.3.3.5.1.24	INTEGER	read-write	The ID of a VLAN of which this port is a member. Port must be untagged. For tagged port which belongs to multiple VLANs, this object return 0 which is an invalid VLAN ID value, reading is valid only for untagged and dual mode, writing is valid for only dual mode.
snSwInfo	1.3.6.1.4.1.1991.1.1.3.1
INT snSwIpMcastQuerierMode	1.3.6.1.4.1.1991.1.1.3.1.15	INTEGER	read-write	The IP Multicast pruning mode is configured either Non-Querier or Querier mode and the default is querier mode. querier(1)...........when prunning traffic locally within the VLAN. nonQuerier(2)........when running with a multicast capable router in the network.
INT snSwIpxL3SwMode	1.3.6.1.4.1.1991.1.1.3.1.28	INTEGER	read-write	The Switch Group is configured with the Layer3 IPX Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate Layer3 Switch disabled(0)..........disable Layer3 Switch
snSwitch	1.3.6.1.4.1.1991.1.1.3			Copyright 1996-2010 Brocade Communications Systems, Inc. All rights reserved. This Brocade Communications Systems SNMP Management Information Base Specification embodies Brocade Communications Systems' confidential and proprietary intellectual property. Brocade Communications Systems retains all title and ownership in the Specification, including any revisions. This Specification is supplied AS IS, and Brocade Communications Systems makes no warranty, either express or implied, as to the use, operation, condition, or performance of the specification, and any unintended consequence it may on the user environment.
I32 snSwMaxMacFilterPerPort	1.3.6.1.4.1.1991.1.1.3.1.37	Integer32	read-only	The maximum number of MAC Filters per port in the Port MAC Access Filter table.
I32 snSwMaxMacFilterPerSystem	1.3.6.1.4.1.1991.1.1.3.1.36	Integer32	read-only	The maximum number of MAC Filters per system in the MAC Filter table.
I32 snSwPortCacheGroupId	1.3.6.1.4.1.1991.1.1.3.3.1.1.32	Integer32	read-write	Cache Group ID for the interface.
STR snSwPortDescr	1.3.6.1.4.1.1991.1.1.3.3.1.1.39	DisplayString	read-only	A textual string containing the slot/port information about the interface.
INT snSwPortDhcpGateListId	1.3.6.1.4.1.1991.1.1.3.3.1.1.23	INTEGER	read-write	The ID for a DHCP gateway list entry relative to this switch port. 0 = unset or no assigned ID
I32 snSwPortEntrySize	1.3.6.1.4.1.1991.1.1.3.1.22	Integer32	read-only	The size of each port table entry.
INT snSwPortFastSpanPortEnable	1.3.6.1.4.1.1991.1.1.3.3.1.1.48	INTEGER	read-write	The enabled/disabled fast span port status of the port.
INT snSwPortFastSpanUplinkEnable	1.3.6.1.4.1.1991.1.1.3.3.1.1.49	INTEGER	read-write	The enabled/disabled fast span uplink status of the port.
INT snSwPortGBICStatus	1.3.6.1.4.1.1991.1.1.3.3.1.1.53	INTEGER	read-only	Indicate if the gig port has GBICs on them. If set to GBIC(1), it means that the port is GBIC. If set to miniGBIC(2), it means that the port miniGBIC. If set to empty(3), it means that the GBIC is missing. Value other(4) means that the port not a removable gig port.
I32 snSwPortIfIndex	1.3.6.1.4.1.1991.1.1.3.3.1.1.38	Integer32	read-only	In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 1213 and RFC 1573.
snSwPortInfo	1.3.6.1.4.1.1991.1.1.3.3
INT snSwPortInfoAdminStatus	1.3.6.1.4.1.1991.1.1.3.3.1.1.8	INTEGER	read-write	The desired state of all ports. The testing(3) state indicates that no operational packets can be passed. (same as ifAdminStatus in MIB-II)
INT snSwPortInfoAutoNegotiate	1.3.6.1.4.1.1991.1.1.3.3.1.1.34	INTEGER	read-write	This feature only applies to Gigabit Ethernet ports. If set to disable(0), port will be put to non-negotiation mode. If set to enable(1), port will start auto-negotiation indefinitely until succeed. If set to negFullAuto(2), the port will start with auto- negotiation, if the negotiation failed, then it will automatically switch to non-negotiation mode. Stackable products (except TurboIron 8) Gigabit Ethernet ports do not support negFullAuto(2). If set to global(3), port negotiation mode follows the value of snSwGlobalAutoNegotiate. Non-Gigabit Ethernet port returns the value other(4).
INT snSwPortInfoChnMode	1.3.6.1.4.1.1991.1.1.3.3.1.1.4	INTEGER	read-write	The port can be configured to operate in either half or full duplex mode. The values are: halfDuplex(1)...half duplex mode fullDuplex(2)...full duplex mode The read-back channel status from hardware are: none(0).........link down or port disabled. halfDuplex(1)...half duplex mode fullDuplex(2)...full duplex mode The port media type (expansion or regular) and port link type (trunk or feeder) determine value of this object. The port can not set to half duplex mode if the port connect mode is m200e(4). However, the value of this parameter may be automatically set whenever the expansion port is connected (e.g. cascade connecting device).
INT snSwPortInfoConnectorType	1.3.6.1.4.1.1991.1.1.3.3.1.1.7	INTEGER	read-only	The type of connector that the port offers. The values are: other(1)...........other or unknown connector copper(2)..........Copper connector fiber(3)...........Fiber connector This describes the physical connector type
snSwPortInfoEntry	1.3.6.1.4.1.1991.1.1.3.3.1.1		not-accessible	An entry in the snSwPortInfo table indicates the configuration on a specified port. A SNMP SET PDU for a row of the snSwPortInfoTable requires the entired sequence of the MIB Objects in each snSwPortInfoEntry stored in one PDU. Otherwise, GENERR return-value will be returned.
INT snSwPortInfoFlowControl	1.3.6.1.4.1.1991.1.1.3.3.1.1.35	INTEGER	read-write	Enable/Disbale port flow control.
INT snSwPortInfoGigType	1.3.6.1.4.1.1991.1.1.3.3.1.1.36	INTEGER	read-only	The media type for the port. The values are: m1000BaseSX(0)....1Gbits per second fiber, with a short wavelength transceiver. m1000BaseLX(1)....1Gbits per second fiber, with a long wavelength transceiver (3km). m1000BaseLH(2)....1Gbits per second fiber, with a special wavelength transceiver (50km). m1000BaseLHA(3)....1Gbits per second fiber, with a special wavelength transceiver (70km). m1000BaseLHB(4)....1Gbits per second fiber, with a special wavelength transceiver (150km). m1000BaseTX(5)....1Gbits per second copper (100meter). m10000BaseSR(6)....10Gbits per second fiber, with a short range wavelength transceiver (100m). m10000BaseLR(7)....10Gbits per second fiber, with a long range wavelength transceiver (10km). m10000BaseER(8)....10Gbits per second fiber, with a extended range wavelength transceiver (40km). sfpCWDM1470nm80Km(9)....1Gbits per second CWDM fiber, with a wavelength 1470nm, reach 80 kms. sfpCWDM1490nm80Km(10)....1Gbits per second CWDM fiber, with a wavelength 1490nm, reach 80 kms. sfpCWDM1510nm80Km(11)....1Gbits per second CWDM fiber, with a wavelength 1510nm, reach 80 kms. sfpCWDM1530nm80Km(12)....1Gbits per second CWDM fiber, with a wavelength 1530nm, reach 80 kms. sfpCWDM1550nm80Km(13)....1Gbits per second CWDM fiber, with a wavelength 1550nm, reach 80 kms. sfpCWDM1570nm80Km(14)....1Gbits per second CWDM fiber, with a wavelength 1570nm, reach 80 kms. sfpCWDM1590nm80Km(15)....1Gbits per second CWDM fiber, with a wavelength 1590nm, reach 80 kms. sfpCWDM1610nm80Km(16)....1Gbits per second CWDM fiber, with a wavelength 1610nm, reach 80 kms. sfpCWDM1470nm100Km(17)....1Gbits per second CWDM fiber, with a wavelength 1470nm, reach 100 kms. sfpCWDM1490nm100Km(18)....1Gbits per second CWDM fiber, with a wavelength 1490nm, reach 100 kms. sfpCWDM1510nm100Km(19)....1Gbits per second CWDM fiber, with a wavelength 1510nm, reach 100 kms. sfpCWDM1530nm100Km(20)....1Gbits per second CWDM fiber, with a wavelength 1530nm, reach 100 kms. sfpCWDM1550nm100Km(21)....1Gbits per second CWDM fiber, with a wavelength 1550nm, reach 100 kms. sfpCWDM1570nm100Km(22)....1Gbits per second CWDM fiber, with a wavelength 1570nm, reach 100 kms. sfpCWDM1590nm100Km(23)....1Gbits per second CWDM fiber, with a wavelength 1590nm, reach 100 kms. sfpCWDM1610nm100Km(24)....1Gbits per second CWDM fiber, with a wavelength 1610nm, reach 100 kms. m1000BaseLHX(25)...1Gbits per second fiber, with a special wavelength transceiver (150km). m2500BaseTX(50)...2.5GBASE fiber. notApplicable(255)....a non-gigabit port.
INT snSwPortInfoLinkStatus	1.3.6.1.4.1.1991.1.1.3.3.1.1.9	INTEGER	read-only	The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. (same as ifOperStatus in MIB-II)
INT snSwPortInfoMediaType	1.3.6.1.4.1.1991.1.1.3.3.1.1.6	INTEGER	read-only	The media type for the port. The values are: other(1).........other or unknown media. m100BaseTX(2)....100Mbits per second copper. m100BaseFX(3)....100Mbits per second fiber. m1000BaseFX(4)...1Gbits per second fiber. mT3(5)...........45Mbits per second (T3). m155ATM(6).......155Mbits per second (ATM). m1000BaseTX(7)...1Gbits per second copper. m622ATM(8).......622Mbits per second (ATM). m155POS(9).......155Mbits per second (POS). m622POS(10)......622Mbits per second (POS). m2488POS(11).....2488Mbits per second (POS). m10000BaseFX(12).10Gbits per second fiber. m9953POS(13).....9953Mbits per second (POS). m16GStacking(14).16Gbits per second fiber. m40GStacking(16). 40Gbits per second fiber.
INT snSwPortInfoMirrorMode	1.3.6.1.4.1.1991.1.1.3.3.1.1.62	INTEGER	read-write	Enable/disable mirror on this port.
INT snSwPortInfoMonitorMode	1.3.6.1.4.1.1991.1.1.3.3.1.1.2	INTEGER	read-write	DEPRECATED by snSwPortInfoMirrorMode and snPortMonitorTable.
PHY snSwPortInfoPhysAddress	1.3.6.1.4.1.1991.1.1.3.3.1.1.11	PhysAddress	read-only	The port physical address. The physical address represents the switch port.
I32 snSwPortInfoPortNum	1.3.6.1.4.1.1991.1.1.3.3.1.1.1	Integer32	read-only	The port index. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only).
INT snSwPortInfoPortQos	1.3.6.1.4.1.1991.1.1.3.3.1.1.10	INTEGER	read-write	The Stand alone stackable switch Port Qos Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron Port Qos Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
INT snSwPortInfoSpeed	1.3.6.1.4.1.1991.1.1.3.3.1.1.5	INTEGER	read-write	The speed configuration for a port. The values are: none(0)..........link down or no traffic. sAutoSense(1)....Auto-sensing 10 or 100Mbits. s10M(2)..........10Mbits per second. s100M(3).........100Mbits per second. s1G(4)...........1Gbits per second. s1GM(5)..........1Gbits per second master. s155M(6).........155Mbits per second (ATM) (for expansion board only). s10G(7)..........10Gbits per second. s622M(8).........OC12 - 622Mbits per second s2488M(9)........OC48 - 2.488Gbits per second s9953M(10).......OC192 - 9.953Gbits per second s16G(11)..........16Gbits per second. s40G(13)..........40Gbits per second. s2500M(14)..........2.5Gbits per second. The read-back hardware status are the following: none(0)..........link down or no traffic. s10M(2)..........10Mbits per second. s100M(3).........100Mbits per second. s1G(4)...........1Gbits per second. s1GM(5)..........1Gbits per second master. s155M(6).........155Mbits per second (ATM) (for expansion board only). s10G(7)..........10Gbits per second. s622M(8).........OC12 - 622Mbits per second s2488M(9)........OC48 - 2.488Gbits per second s9953M(10).......OC192 - 9.953Gbits per second s16G(11)..........16Gbits per second. s40G(13)..........40Gbits per second. s2500M(14)..........2.5Gbits per second. The port media type (expansion or regular) and port link type (trunk or feeder) determine whether this object can be written and the valid values. It is not allowed to change speed for trunks ports. For expansion ports, all of the above speed can be set. However, the value of this parameter may be automatically set whenever the expansion port is connected (e.g. cascade connecting device).
snSwPortInfoTable	1.3.6.1.4.1.1991.1.1.3.3.1		not-accessible	A specific snSwPortInfo group consists of a number of switch ports.
INT snSwPortInfoTagMode	1.3.6.1.4.1.1991.1.1.3.3.1.1.3	INTEGER	read-write	For tagged port, we could have multiple VLANs per port. For untagged port or auto port, there is only one VLAN ID per port.
INT snSwPortInLinePowerClass	1.3.6.1.4.1.1991.1.1.3.3.1.1.60	INTEGER	read-write	Adjust the inline power class. This object can only be set after snSwPortInLinePowerControl has been set to 'enable(3)' or 'enableLegacyDevice(4)'. If a port does not have inline power capability, reading this object returns undefined value.
I32 snSwPortInLinePowerConsumed	1.3.6.1.4.1.1991.1.1.3.3.1.1.66	Integer32	read-only	Inline power consumed by the port. Each unit is milliwatts.
INT snSwPortInLinePowerControl	1.3.6.1.4.1.1991.1.1.3.3.1.1.58	INTEGER	read-write	Control inline power on/off to a port. If a port does not have inline power capability, reading this object returns 'other(1)'.
STR snSwPortInLinePowerPDType	1.3.6.1.4.1.1991.1.1.3.3.1.1.67	DisplayString	read-only	Inline Power device type 802.3af or Legacy device.
INT snSwPortInLinePowerPriority	1.3.6.1.4.1.1991.1.1.3.3.1.1.61	INTEGER	read-write	Inline power allocation priority for the power device 0- Not a POE port, 1- Critical, 2- High, 3- Low, 4- Medium, 5- other.
I32 snSwPortInLinePowerWattage	1.3.6.1.4.1.1991.1.1.3.3.1.1.59	Integer32	read-write	Adjust the inline power wattage. Valid value between 1000 and 15400. Each unit is milliwatts. This object can only be set after snSwPortInLinePowerControl has been set to 'enable(3)' or 'enableLegacyDevice(4)'. If a port does not have inline power capability, reading this object returns undefined value.
OCT snSwPortInOctets	1.3.6.1.4.1.1991.1.1.3.3.1.1.40	OCTET STRING	read-only	The total number of octets received on the interface, including framing characters. This object is a 64-bit counter of the ifInOctets object, defined in RFC 1213. The octet string is in big-endian byte order.
INT snSwPortLoadInterval	1.3.6.1.4.1.1991.1.1.3.3.1.1.56	INTEGER	read-write	The time in seconds for which average port utilization should be carried out. The value should be incremental of 30 seconds, between the ranges specified.
INT snSwPortLockAddressCount	1.3.6.1.4.1.1991.1.1.3.3.1.1.21	INTEGER	read-write	The number of source MAC addresses are allowed for a port. Writing 0 to this object will allow any number of addresses.
STR snSwPortName	1.3.6.1.4.1.1991.1.1.3.3.1.1.24	DisplayString	read-write	Port Name string.
OCT snSwPortOutOctets	1.3.6.1.4.1.1991.1.1.3.3.1.1.41	OCTET STRING	read-only	The total number of octets transmitted out of the interface, including framing characters. This object is a 64-bit counter of the ifOutOctets object, defined in RFC 1213. The octet string is in big-endian byte order.
INT snSwPortPresent	1.3.6.1.4.1.1991.1.1.3.3.1.1.52	INTEGER	read-only	Indicate if the port is absent or present. This object only valid for M4 module
INT snSwPortRouteOnly	1.3.6.1.4.1.1991.1.1.3.3.1.1.51	INTEGER	read-write	Enable/Disable L2 switching of a routing switch port. By default, the routing switch performs routing first. If routing failed, it performs switching. Enable route only instrcuts the routing switch to perform routing only. For a L2 switching only product, reading this object always return 'disabled', writing 'enabled' to this object takes no effect.
I32 snSwPortSetAll	1.3.6.1.4.1.1991.1.1.3.1.8	Integer32	read-write	The value of this object is the index number of the snSwPortInfoTable (snSwPortInfoPortIndex). snSwPortInfoMonitorMode, snSwPortInfoTagMode, snSwPortInfoChnMode, snSwPortInfoSpeed, snSwPortInfoAdminStatus are all the read-write attributes of that row of table. They will be used to set the same attributes for all the ports in the system. Note: prior setting this object, all the intended attributes of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire port-table. The previous setting will be overwritten by the new one.
C32 snSwPortStatsAlignErrors	1.3.6.1.4.1.1991.1.1.3.3.1.1.14	Counter32	read-only	dot3StatsAlignmentErrors : A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
C32 snSwPortStatsFCSErrors	1.3.6.1.4.1.1991.1.1.3.3.1.1.15	Counter32	read-only	dot3StatsFCSErrors : A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
C32 snSwPortStatsFrameTooLongs	1.3.6.1.4.1.1991.1.1.3.3.1.1.17	Counter32	read-only	dot3StatsFrameTooLongs : A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
C32 snSwPortStatsFrameTooShorts	1.3.6.1.4.1.1991.1.1.3.3.1.1.20	Counter32	read-only	A count of frames received on a particular interface that below the minimum permitted frame size.
C32 snSwPortStatsInBcastFrames	1.3.6.1.4.1.1991.1.1.3.3.1.1.25	Counter32	read-only	The total number of broadcast packets received on the interface.
G32 snSwPortStatsInBitsPerSec	1.3.6.1.4.1.1991.1.1.3.3.1.1.42	Gauge32	read-only	The number of bits per second received on the interface over a 5 minutes interval.
C32 snSwPortStatsInDiscard	1.3.6.1.4.1.1991.1.1.3.3.1.1.29	Counter32	read-only	The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
C32 snSwPortStatsInFrames	1.3.6.1.4.1.1991.1.1.3.3.1.1.12	Counter32	read-only	The total number of packets received on the interface.
C64 snSwPortStatsInJumboFrames	1.3.6.1.4.1.1991.1.1.3.3.1.1.63	Counter64	read-only	The total number of jumbo packets received on the interface.
U32 snSwPortStatsInKiloBitsPerSec	1.3.6.1.4.1.1991.1.1.3.3.1.1.54	Unsigned32	read-only	Bit rate in kilobits per second received on the 10G and faster interface over a 5 minutes interval.
C32 snSwPortStatsInMcastFrames	1.3.6.1.4.1.1991.1.1.3.3.1.1.27	Counter32	read-only	The total number of multicast packets received on the interface.
G32 snSwPortStatsInPktsPerSec	1.3.6.1.4.1.1991.1.1.3.3.1.1.44	Gauge32	read-only	The number of packets per second received on the interface over a 5 minutes interval.
INT snSwPortStatsInUtilization	1.3.6.1.4.1.1991.1.1.3.3.1.1.46	INTEGER	read-only	The input network utilization in hundredths of a percent over a 5 minutes interval.
C32 snSwPortStatsLinkChange	1.3.6.1.4.1.1991.1.1.3.3.1.1.37	Counter32	read-only	The total number of link state change of the interface.
I32 snSwPortStatsMacStations	1.3.6.1.4.1.1991.1.1.3.3.1.1.31	Integer32	read-only	The total number of MAC Stations connected to the interface.
C32 snSwPortStatsMultiColliFrames	1.3.6.1.4.1.1991.1.1.3.3.1.1.16	Counter32	read-only	dot3StatsMultipleCollisionFrames : A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object.
C32 snSwPortStatsOutBcastFrames	1.3.6.1.4.1.1991.1.1.3.3.1.1.26	Counter32	read-only	The total number of broadcast packets transmitted out of the interface.
G32 snSwPortStatsOutBitsPerSec	1.3.6.1.4.1.1991.1.1.3.3.1.1.43	Gauge32	read-only	The number of bits per second transmitted out of the interface over a 5 minutes interval.
C32 snSwPortStatsOutDiscard	1.3.6.1.4.1.1991.1.1.3.3.1.1.30	Counter32	read-only	The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
C32 snSwPortStatsOutFrames	1.3.6.1.4.1.1991.1.1.3.3.1.1.13	Counter32	read-only	The total number of packets transmitted out of the interface.
C64 snSwPortStatsOutJumboFrames	1.3.6.1.4.1.1991.1.1.3.3.1.1.64	Counter64	read-only	The total number of jumbo packets transmitted out of the interface.
U32 snSwPortStatsOutKiloBitsPerSec	1.3.6.1.4.1.1991.1.1.3.3.1.1.55	Unsigned32	read-only	Bit rate in kilobits per second transmitted out of the 10G and faster interface over a 5 minutes interval.
C32 snSwPortStatsOutMcastFrames	1.3.6.1.4.1.1991.1.1.3.3.1.1.28	Counter32	read-only	The total number of multicast packets transmitted out of the interface.
G32 snSwPortStatsOutPktsPerSec	1.3.6.1.4.1.1991.1.1.3.3.1.1.45	Gauge32	read-only	The number of packets per second transmitted out of the interface over a 5 minutes interval.
INT snSwPortStatsOutUtilization	1.3.6.1.4.1.1991.1.1.3.3.1.1.47	INTEGER	read-only	The output network utilization in hundredths of a percent over a 5 minutes interval.
C32 snSwPortStatsRxColliFrames	1.3.6.1.4.1.1991.1.1.3.3.1.1.19	Counter32	read-only	A count of successfully received frames on a particular interface for which transmission is inhibited by more than one collision. This object is not specified in dot3 but it has the same functionarity as snSwPortStatsTxColliFrames.
C32 snSwPortStatsTxColliFrames	1.3.6.1.4.1.1991.1.1.3.3.1.1.18	Counter32	read-only	A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by a combination of both dot3StatsSingleCollisionFrames and dot3StatsMultipleCollisionFrames objects.
INT snSwPortStpPortEnable	1.3.6.1.4.1.1991.1.1.3.3.1.1.22	INTEGER	read-write	The enabled/disabled status of the port.
I32 snSwPortTagType	1.3.6.1.4.1.1991.1.1.3.3.1.1.57	Integer32	read-write	The IEEE802.1q tag type embedded in the length/type field of an Ethernet packet. It specifies that the 2 octets after the length/type field in an Ethernet packet is the tag value.
I32 snSwPortTransGroupId	1.3.6.1.4.1.1991.1.1.3.3.1.1.33	Integer32	read-write	Transparent Group ID for the interface.
INT snSwPortVlanId	1.3.6.1.4.1.1991.1.1.3.3.1.1.50	INTEGER	read-write	The ID of a VLAN of which this port is a member. Port must be untagged. For tagged port which belongs to multiple VLANs, this object return 0 which is an invalid VLAN ID value.
I32 snSwProbePortNum	1.3.6.1.4.1.1991.1.1.3.1.12	Integer32	read-write	A chassis switch probe port is operated as a traffic analyzer port and only one port can be assigned in the chassis. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number. A stackable switch is only assigned with one probe port as a traffic analyzer.
INT snSwProtocolVLanMode	1.3.6.1.4.1.1991.1.1.3.1.31	INTEGER	read-write	disabled(0) - represents system with Protocol VLAN disabled. enabled(1) - represents system with Protocol VLAN enabled (Layer3 VLAN).
INT snSwQosMechanism	1.3.6.1.4.1.1991.1.1.3.1.40	INTEGER	read-write	Indicates whether the qos mechanism is strict or weighted. This object is not supported on NI platform.
INT snSwSingleStpMode	1.3.6.1.4.1.1991.1.1.3.1.41	INTEGER	read-write	Single Spanning Tree System Mode in the Switch Group can be set either enabled or disabled and the default is disabled mode. disable(0)...........no Single Spanning Tree enableStp(1).........activate SSTP control vlan to run Spanning Tree enableRstp(2)........activate SSTP control vlan to run Rapid Spanning Tree
I32 snSwSingleStpVLanId	1.3.6.1.4.1.1991.1.1.3.1.44	Integer32	read-only	The VLAN ID of the Single Spanning Tree VLAN if Single Spanning Tree was enabled. This object returns zero if Single Spanning Tree was disabled.
snSwSummary	1.3.6.1.4.1.1991.1.1.3.7
INT snSwSummaryMode	1.3.6.1.4.1.1991.1.1.3.7.1	INTEGER	read-write	The Switch Group Configuration Summary is configured either enabled or disabled and the default is disabled mode. enabled(1)...........activate Switch Configuration Summary. disabled(0)..........no Switch Configuration Summary.
I32 snSwViolatorIfIndex	1.3.6.1.4.1.1991.1.1.3.1.43	Integer32	read-only	The port number of the switch or router that received a violator packet. It is included in the locked address violation trap.
MAC snSwViolatorMacAddress	1.3.6.1.4.1.1991.1.1.3.1.18	MacAddress	read-only	The source address of the violator packet received by the switch or router. It is included in the locked address violation trap.
I32 snSwViolatorPortNumber	1.3.6.1.4.1.1991.1.1.3.1.17	Integer32	read-only	The port number of the switch or router that received a violator packet. It is included in the locked address violation trap. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only).
snTacacs	1.3.6.1.4.1.1991.1.1.3.13
INT snTacacsDeadTime	1.3.6.1.4.1.1991.1.1.3.13.1.3	INTEGER	read-write	Interval specifies Tacacs server dead time, each unit is one minute.
snTacacsGeneral	1.3.6.1.4.1.1991.1.1.3.13.1
STR snTacacsKey	1.3.6.1.4.1.1991.1.1.3.13.1.4	DisplayString	read-write	Authentication key displayed as encrypted text. Write operation can only be done if the SET request uses SNMPv3 with data encrypted using privacy key. FastIron and NetIron platforms support keysize upto 64 characters.
INT snTacacsRetransmit	1.3.6.1.4.1.1991.1.1.3.13.1.1	INTEGER	read-write	The number of authentication query retransmissions to the Tacacs server.
I32 snTacacsServerAuthPort	1.3.6.1.4.1.1991.1.1.3.13.2.1.2	Integer32	read-write	Authentication UDP port number.
snTacacsServerEntry	1.3.6.1.4.1.1991.1.1.3.13.2.1		not-accessible	An entry in the Tacacs server table.
IP snTacacsServerIp	1.3.6.1.4.1.1991.1.1.3.13.2.1.1	IpAddress	read-only	Tacacs server IP address.
STR snTacacsServerRowKey	1.3.6.1.4.1.1991.1.1.3.13.2.1.4	DisplayString	read-write	Authentication key displayed as encrypted text. Write operation can only be done if the SET request uses SNMPv3 with data encrypted using privacy key. FastIron and NetIron platforms support keysize upto 64 characters.
INT snTacacsServerRowStatus	1.3.6.1.4.1.1991.1.1.3.13.2.1.3	INTEGER	read-write	To create or delete a Tacacs server table entry.
snTacacsServerTable	1.3.6.1.4.1.1991.1.1.3.13.2		not-accessible	Tacacs server table.
INT snTacacsServerUsage	1.3.6.1.4.1.1991.1.1.3.13.2.1.5	INTEGER	read-write	To allow this server to be dedicated for a particular AAA activity.
INT snTacacsSNMPAccess	1.3.6.1.4.1.1991.1.1.3.13.1.5	INTEGER	read-only	Indicate whether TACACS+ server and key related MIB objects can be accessed by SNMP manager. If value is disabled, then snTacacsKey and snTacacsServerTable MIB objects will not be accessible.
INT snTacacsTimeOut	1.3.6.1.4.1.1991.1.1.3.13.1.2	INTEGER	read-write	Interval specifies how long to wait for authentication reply from the Tacacs server, each unit is one second.
snTrunkEntry	1.3.6.1.4.1.1991.1.1.3.6.1.1		not-accessible	An entry in the snTrunkTable indicates the configuration on a specified Trunk port membership.
I32 snTrunkIndex	1.3.6.1.4.1.1991.1.1.3.6.1.1.1	Integer32	read-only	The number of the trunk entries can be configured. This can be 32* for Jetcore, and 16* for Ironcore.
snTrunkInfo	1.3.6.1.4.1.1991.1.1.3.6
snTrunkInterface	1.3.6.1.4.1.1991.1.1.3.3.2.11
POR snTrunkPortMask	1.3.6.1.4.1.1991.1.1.3.6.1.1.2	PortMask	read-write	Trunk membership of the Switch.
snTrunkTable	1.3.6.1.4.1.1991.1.1.3.6.1		not-accessible	A specific snTrunkTable consists of a number of Trunk port-mask.
INT snTrunkType	1.3.6.1.4.1.1991.1.1.3.6.1.1.3	INTEGER	read-write	The trunk connection type which specifies what device the trunk ports are connected to.
snVirtualInterface	1.3.6.1.4.1.1991.1.1.3.3.2.4
snVirtualMgmtInterface	1.3.6.1.4.1.1991.1.1.3.3.2.12
OCT snVLanByATCableChassisStaticMask	1.3.6.1.4.1.1991.1.1.3.2.5.1.5	OCTET STRING	read-write	A list of ports which are statically configured to become port members of a VLAN. (It was obsoleted after release 07100, replaced by snVLanByATCableStaticPortList)
snVLanByATCableEntry	1.3.6.1.4.1.1991.1.1.3.2.5.1		not-accessible	An entry of the AppleTalk Cable VLAN table.
I32 snVLanByATCableIndex	1.3.6.1.4.1.1991.1.1.3.2.5.1.2	Integer32	read-only	AppleTalk Cable VLAN index number.
INT snVLanByATCableRouterIntf	1.3.6.1.4.1.1991.1.1.3.2.5.1.3	INTEGER	read-write	A virtual router interface to the AppleTalk Cable VLAN, only router products accept the SNMP-SET operation. The value zero indicates that virtual router interface was not configured.
INT snVLanByATCableRowStatus	1.3.6.1.4.1.1991.1.1.3.2.5.1.4	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
OCT snVLanByATCableStaticPortList	1.3.6.1.4.1.1991.1.1.3.2.5.1.7	OCTET STRING	read-write	A list of port indices which are the configured port membership of the AppleTalk Cable VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
snVLanByATCableTable	1.3.6.1.4.1.1991.1.1.3.2.5		not-accessible	A Table Of VLAN By AppleTalk Network Number.
INT snVLanByATCableVLanId	1.3.6.1.4.1.1991.1.1.3.2.5.1.1	INTEGER	read-only	The VLAN ID of a PORT VLAN of which the AppleTalk Cable VLAN was attaching to.
STR snVLanByATCableVLanName	1.3.6.1.4.1.1991.1.1.3.2.5.1.6	DisplayString	read-write	VLAN Name string.
OCT snVLanByIpSubnetChassisDynamicMask	1.3.6.1.4.1.1991.1.1.3.2.3.1.12	OCTET STRING	read-only	The Chassis VLAN By Subnet active port membership. (It was obsoleted after release 07100, replaced by snVLanByIpSubnetDynamicPortList)
OCT snVLanByIpSubnetChassisExcludeMask	1.3.6.1.4.1.1991.1.1.3.2.3.1.11	OCTET STRING	read-write	The Chassis VLAN By Subnet port membership applied in exclusive mode. (It was obsoleted after release 07100, replaced by snVLanByIpSubnetExcludePortList)
OCT snVLanByIpSubnetChassisStaticMask	1.3.6.1.4.1.1991.1.1.3.2.3.1.10	OCTET STRING	read-write	The Chassis VLAN By Subnet port membership applied in static mode. (It was obsoleted after release 07100, replaced by snVLanByIpSubnetStaticPortList)
INT snVLanByIpSubnetDynamic	1.3.6.1.4.1.1991.1.1.3.2.3.1.4	INTEGER	read-write	disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only.
POR snVLanByIpSubnetDynamicMask	1.3.6.1.4.1.1991.1.1.3.2.3.1.9	PortMask	read-only	The Standand-alone switch VLAN By Subnet active port membership. (It was obsoleted for Chassis Product)
OCT snVLanByIpSubnetDynamicPortList	1.3.6.1.4.1.1991.1.1.3.2.3.1.16	OCTET STRING	read-only	A list of port indices which are dynamically joining the port membership of the VLAN By IP Subnet. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
snVLanByIpSubnetEntry	1.3.6.1.4.1.1991.1.1.3.2.3.1		not-accessible	An entry in the VLAN By IP Subnet Configuration table.
POR snVLanByIpSubnetExcludeMask	1.3.6.1.4.1.1991.1.1.3.2.3.1.6	PortMask	read-write	The Standand-alone switch VLAN By Subnet port membership applied in exclusive mode. (It was obsoleted for Chassis Product)
OCT snVLanByIpSubnetExcludePortList	1.3.6.1.4.1.1991.1.1.3.2.3.1.15	OCTET STRING	read-write	A list of port indices which are the excluded from port membership of the VLAN By IP Subnet. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
IP snVLanByIpSubnetIpAddress	1.3.6.1.4.1.1991.1.1.3.2.3.1.2	IpAddress	read-only	Subnet IP address.
I32 snVLanByIpSubnetMaxSubnets	1.3.6.1.4.1.1991.1.1.3.1.29	Integer32	read-only	The maximum number of subnets for each IP VLAN.
INT snVLanByIpSubnetRouterIntf	1.3.6.1.4.1.1991.1.1.3.2.3.1.7	INTEGER	read-write	Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured.
INT snVLanByIpSubnetRowStatus	1.3.6.1.4.1.1991.1.1.3.2.3.1.8	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
POR snVLanByIpSubnetStaticMask	1.3.6.1.4.1.1991.1.1.3.2.3.1.5	PortMask	read-write	The Standand-alone switch VLAN By Subnet port membership applied in static mode. (It was obsoleted for Chassis Product)
OCT snVLanByIpSubnetStaticPortList	1.3.6.1.4.1.1991.1.1.3.2.3.1.14	OCTET STRING	read-write	A list of port indices which are the configured port membership of the VLAN By IP Subnet. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
IP snVLanByIpSubnetSubnetMask	1.3.6.1.4.1.1991.1.1.3.2.3.1.3	IpAddress	read-only	Subnet mask associated with the Subnet IP address.
snVLanByIpSubnetTable	1.3.6.1.4.1.1991.1.1.3.2.3		not-accessible	An entry of the VLAN By IPX Network Number Table.
INT snVLanByIpSubnetVLanId	1.3.6.1.4.1.1991.1.1.3.2.3.1.1	INTEGER	read-only	The VLAN ID index to both of the VLAN By Port Info Table and this table.
STR snVLanByIpSubnetVLanName	1.3.6.1.4.1.1991.1.1.3.2.3.1.13	DisplayString	read-write	VLAN Community Name string.
OCT snVLanByIpxNetChassisDynamicMask	1.3.6.1.4.1.1991.1.1.3.2.4.1.12	OCTET STRING	read-only	The Chassis VLAN By IPX network active port membership. (It was obsoleted after release 07100, replaced by snVLanByIpxNetDynamicPortList)
OCT snVLanByIpxNetChassisExcludeMask	1.3.6.1.4.1.1991.1.1.3.2.4.1.11	OCTET STRING	read-write	The Chassis VLAN By IPX network port membership applied in exclusive mode. (It was obsoleted after release 07100, replaced by snVLanByIpxNetExcludePortList)
OCT snVLanByIpxNetChassisStaticMask	1.3.6.1.4.1.1991.1.1.3.2.4.1.10	OCTET STRING	read-write	The Chassis VLAN By IPX network port membership applied in static mode. (It was obsoleted after release 07100, replaced by snVLanByIpxNetStaticPortList)
INT snVLanByIpxNetDynamic	1.3.6.1.4.1.1991.1.1.3.2.4.1.4	INTEGER	read-write	disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only.
POR snVLanByIpxNetDynamicMask	1.3.6.1.4.1.1991.1.1.3.2.4.1.9	PortMask	read-only	The VLAN By IPX network active port membership. (It was obsoleted for Chassis Product)
OCT snVLanByIpxNetDynamicPortList	1.3.6.1.4.1.1991.1.1.3.2.4.1.16	OCTET STRING	read-only	A list of port indices which are dynamically joining the port membership of the VLAN By IPX network. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
snVLanByIpxNetEntry	1.3.6.1.4.1.1991.1.1.3.2.4.1		not-accessible	An entry in the VLAN By Ipx Network Number Configuration table.
POR snVLanByIpxNetExcludeMask	1.3.6.1.4.1.1991.1.1.3.2.4.1.6	PortMask	read-write	The VLAN By IPX network port membership applied in exclusive mode. (It was obsoleted for Chassis Product)
OCT snVLanByIpxNetExcludePortList	1.3.6.1.4.1.1991.1.1.3.2.4.1.15	OCTET STRING	read-write	A list of port indices which are the excluded from port membership of the VLAN By IPX network. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
INT snVLanByIpxNetFrameType	1.3.6.1.4.1.1991.1.1.3.2.4.1.3	INTEGER	read-only	The following IPX Frame types are operated in Layer3 VLAN such as : ipxEthernet8022(1), ipxEthernet8023(2), ipxEthernetII(3), ipxEthernetSnap(4). choose notApplicable(0) for other protocols. Note: Each Network Number can be assigned with one unique Frame type; Otherwise, a SNMP-SET error will be returned.
I32 snVLanByIpxNetMaxNetworks	1.3.6.1.4.1.1991.1.1.3.1.30	Integer32	read-only	The maximum number of networks for each IPX VLAN.
OCT snVLanByIpxNetNetworkNum	1.3.6.1.4.1.1991.1.1.3.2.4.1.2	OCTET STRING	read-only	IPX Network Number.
INT snVLanByIpxNetRouterIntf	1.3.6.1.4.1.1991.1.1.3.2.4.1.7	INTEGER	read-write	Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured.
INT snVLanByIpxNetRowStatus	1.3.6.1.4.1.1991.1.1.3.2.4.1.8	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
POR snVLanByIpxNetStaticMask	1.3.6.1.4.1.1991.1.1.3.2.4.1.5	PortMask	read-write	The VLAN By IPX network port membership applied in static mode. (It was obsoleted for Chassis Product)
OCT snVLanByIpxNetStaticPortList	1.3.6.1.4.1.1991.1.1.3.2.4.1.14	OCTET STRING	read-write	A list of port indices which are the configured port membership of the VLAN By IPX network. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
snVLanByIpxNetTable	1.3.6.1.4.1.1991.1.1.3.2.4		not-accessible	An entry of the VLAN By IPX Network Number Table.
INT snVLanByIpxNetVLanId	1.3.6.1.4.1.1991.1.1.3.2.4.1.1	INTEGER	read-only	The VLAN ID index to both of the VLAN By Port Info Table and this table.
STR snVLanByIpxNetVLanName	1.3.6.1.4.1.1991.1.1.3.2.4.1.13	DisplayString	read-write	VLAN Community Name string.
MAC snVLanByPortBaseBridgeAddress	1.3.6.1.4.1.1991.1.1.3.2.1.1.24	MacAddress	read-only	The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with dot1dStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
I32 snVLanByPortBaseNumPorts	1.3.6.1.4.1.1991.1.1.3.2.1.1.12	Integer32	read-only	The number of ports controlled by this bridging entity.
INT snVLanByPortBaseType	1.3.6.1.4.1.1991.1.1.3.2.1.1.13	INTEGER	read-only	Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
MAC snVLanByPortCfgBaseBridgeAddress	1.3.6.1.4.1.1991.1.1.3.2.7.1.20	MacAddress	read-only	The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with dot1dStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol.
I32 snVLanByPortCfgBaseNumPorts	1.3.6.1.4.1.1991.1.1.3.2.7.1.8	Integer32	read-only	The number of ports controlled by this bridging entity.
INT snVLanByPortCfgBaseType	1.3.6.1.4.1.1991.1.1.3.2.7.1.9	INTEGER	read-only	Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
snVLanByPortCfgEntry	1.3.6.1.4.1.1991.1.1.3.2.7.1		not-accessible	An entry of the port VLAN configuration table.
C64 snVLanByPortCfgInOctets	1.3.6.1.4.1.1991.1.1.3.2.7.1.25	Counter64	read-only	The number of bytes received on this VLAN. This can be used as the per VE couter, if there is one-to-one map for VLAN-VE.
POR snVLanByPortCfgQos	1.3.6.1.4.1.1991.1.1.3.2.7.1.2	PortQosTC	read-write	The Stand alone stackable switch VLAN Priority values are: level0(0) -- low prority level1(1) -- high prority. The BigIron switch VLAN Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7). Value invalid(127) is used by CES/CER products to signify that no QoS was specified for this VLAN.
I32 snVLanByPortCfgRouterIntf	1.3.6.1.4.1.1991.1.1.3.2.7.1.22	Integer32	read-write	Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured.
INT snVLanByPortCfgRowStatus	1.3.6.1.4.1.1991.1.1.3.2.7.1.23	INTEGER	read-write	Use this object to delete a vlan entry. For read operation, its value is 'valid' if it is a user-configured VLAN and 'other' if it is a control-VLAN.
BRI snVLanByPortCfgStpDesignatedRoot	1.3.6.1.4.1.1991.1.1.3.2.7.1.19	BridgeId	read-only	dot1dStpDesignatedRoot: From RFC1493(Bridge MIB). The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
TIM snVLanByPortCfgStpForwardDelay	1.3.6.1.4.1.1991.1.1.3.2.7.1.14	Timeout	read-only	dot1dStpForwardDelay: From RFC1493(Bridge MIB). This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
I32 snVLanByPortCfgStpGroupForwardDelay	1.3.6.1.4.1.1991.1.1.3.2.7.1.7	Integer32	read-write	dot1dStpBridgeForwardDelay : From RFC1493(Bridge MIB). The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. Valid value between 2 and 30. Default is 15 seconds. Value 0 is returned if no STP is not configured for this vlan.
I32 snVLanByPortCfgStpGroupHelloTime	1.3.6.1.4.1.1991.1.1.3.2.7.1.6	Integer32	read-write	dot1dStpBridgeHelloTime: From RFC1493(Bridge MIB). The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. Valid value between 1 and 10. Default is 2 seconds. Value 0 is returned if no STP is not configured for this vlan.
I32 snVLanByPortCfgStpGroupMaxAge	1.3.6.1.4.1.1991.1.1.3.2.7.1.5	Integer32	read-write	dot1dStpBridgeMaxAge: From RFC1493(Bridge MIB). The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. Valid value between 6 and 40. Default is 20 seconds. Value 0 is returned if no STP is not configured for this vlan.
TIM snVLanByPortCfgStpHelloTime	1.3.6.1.4.1.1991.1.1.3.2.7.1.12	Timeout	read-only	dot1dStpHelloTime: From RFC1493(Bridge MIB). The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
I32 snVLanByPortCfgStpHoldTime	1.3.6.1.4.1.1991.1.1.3.2.7.1.13	Integer32	read-only	dot1dStpHoldTime: From RFC1493(Bridge MIB). This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
TIM snVLanByPortCfgStpMaxAge	1.3.6.1.4.1.1991.1.1.3.2.7.1.11	Timeout	read-only	dot1dStpMaxAge: From RFC1493(Bridge MIB). The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT snVLanByPortCfgStpMode	1.3.6.1.4.1.1991.1.1.3.2.7.1.3	INTEGER	read-write	Spanning Tree Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. disable(0)...........no Spanning Tree enableStp(1).........activate Spanning Tree enableRstp(2)........activate Rapid Spanning Tree
INT snVLanByPortCfgStpPriority	1.3.6.1.4.1.1991.1.1.3.2.7.1.4	INTEGER	read-write	dot1dStpPriority : The value of the write-able portion of the Stp ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of the base bridge address - dot1dBaseBridgeAddress.
INT snVLanByPortCfgStpProtocolSpecification	1.3.6.1.4.1.1991.1.1.3.2.7.1.10	INTEGER	read-only	An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
I32 snVLanByPortCfgStpRootCost	1.3.6.1.4.1.1991.1.1.3.2.7.1.17	Integer32	read-only	dot1dStpRootCost: From RFC1493(Bridge MIB). The cost of the path to the root as seen from this bridge.
I32 snVLanByPortCfgStpRootPort	1.3.6.1.4.1.1991.1.1.3.2.7.1.18	Integer32	read-only	dot1dStpRootPort: From RFC1493(Bridge MIB). The port number of the port which offers the lowest cost path from this bridge to the root bridge.
TIK snVLanByPortCfgStpTimeSinceTopologyChange	1.3.6.1.4.1.1991.1.1.3.2.7.1.15	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
C32 snVLanByPortCfgStpTopChanges	1.3.6.1.4.1.1991.1.1.3.2.7.1.16	Counter32	read-only	The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
INT snVLanByPortCfgStpVersion	1.3.6.1.4.1.1991.1.1.3.2.7.1.24	INTEGER	read-write	The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w. New value may be defined as future versions of the protocol become available.
snVLanByPortCfgTable	1.3.6.1.4.1.1991.1.1.3.2.7		not-accessible	Port VLAN (Layer 2 VLAN) configuration table.
INT snVLanByPortCfgTransparentHwFlooding	1.3.6.1.4.1.1991.1.1.3.2.7.1.26	INTEGER	read-write	Specifies the transparent VLAN flooding feature.
INT snVLanByPortCfgVLanId	1.3.6.1.4.1.1991.1.1.3.2.7.1.1	INTEGER	read-only	The VLAN identifier (VLAN ID).
STR snVLanByPortCfgVLanName	1.3.6.1.4.1.1991.1.1.3.2.7.1.21	DisplayString	read-write	VLAN Community Name string.
OCT snVLanByPortChassisPortMask	1.3.6.1.4.1.1991.1.1.3.2.1.1.27	OCTET STRING	read-write	The Chassis VLAN switch port membership. (It was obsoleted after release 07100, replaced by snVLanByPortPortList)
snVLanByPortEntry	1.3.6.1.4.1.1991.1.1.3.2.1.1		not-accessible	An entry in the VLAN By Port Information table. snVLanByPortVLanIndex = 1 and with snVLanByPortVLanId = 1 together implies all attributes applying to the Global switch group i.e. noVLan. A SNMP SET PDU for a row of the snVLanByPortTable requires the entired sequence of the MIB Objects in each snVLanByPortEntry stored in one PDU. Otherwise, GENERR return-value will be returned.
I32 snVLanByPortEntrySize	1.3.6.1.4.1.1991.1.1.3.1.21	Integer32	read-only	The size of each VLAN table entry.
snVLanByPortMemberEntry	1.3.6.1.4.1.1991.1.1.3.2.6.1		not-accessible	An entry of the port VLAN membership table.
NUM snVLanByPortMemberPortId	1.3.6.1.4.1.1991.1.1.3.2.6.1.2	InterfaceIndex	read-only	The ifIndex which is a member of the port VLAN.
INT snVLanByPortMemberRowStatus	1.3.6.1.4.1.1991.1.1.3.2.6.1.3	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
snVLanByPortMemberTable	1.3.6.1.4.1.1991.1.1.3.2.6		not-accessible	Port VLAN (Layer 2 VLAN) port membership table.
INT snVLanByPortMemberTagMode	1.3.6.1.4.1.1991.1.1.3.2.6.1.4	INTEGER	read-write	For tagged/dual-mode port, we could have multiple VLANs per port. For untagged port, there is only one VLAN ID per port.
INT snVLanByPortMemberVLanId	1.3.6.1.4.1.1991.1.1.3.2.6.1.1	INTEGER	read-only	The VLAN identifier (VLAN ID).
INT snVLanByPortOperState	1.3.6.1.4.1.1991.1.1.3.2.1.1.11	INTEGER	read-only	By default, this mode is set to notActivated(0). notActivated(0)...the VLAN entry is not activated and not in running mode. activated(1)......the VLAN entry is activated and in running mode
OCT snVLanByPortPortList	1.3.6.1.4.1.1991.1.1.3.2.1.1.28	OCTET STRING	read-write	A list of port indices which are the port membership of a VLAN By Port. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
POR snVLanByPortPortMask	1.3.6.1.4.1.1991.1.1.3.2.1.1.3	PortMask	read-write	The Standand-alone switch VLAN port membership. (It was obsoleted for Chassis Product)
INT snVLanByPortQos	1.3.6.1.4.1.1991.1.1.3.2.1.1.4	INTEGER	read-write	The Stand alone stackable switch VLAN Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron switch VLAN Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
I32 snVLanByPortRouterIntf	1.3.6.1.4.1.1991.1.1.3.2.1.1.26	Integer32	read-write	Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured.
INT snVLanByPortRowStatus	1.3.6.1.4.1.1991.1.1.3.2.1.1.10	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
BRI snVLanByPortStpDesignatedRoot	1.3.6.1.4.1.1991.1.1.3.2.1.1.23	BridgeId	read-only	dot1dStpDesignatedRoot: From RFC1493(Bridge MIB). The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
TIM snVLanByPortStpForwardDelay	1.3.6.1.4.1.1991.1.1.3.2.1.1.18	Timeout	read-only	dot1dStpForwardDelay: From RFC1493(Bridge MIB). This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
INT snVLanByPortStpGroupForwardDelay	1.3.6.1.4.1.1991.1.1.3.2.1.1.9	INTEGER	read-write	dot1dStpBridgeForwardDelay : From RFC1493(Bridge MIB). The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
INT snVLanByPortStpGroupHelloTime	1.3.6.1.4.1.1991.1.1.3.2.1.1.8	INTEGER	read-write	dot1dStpBridgeHelloTime: From RFC1493(Bridge MIB). The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
INT snVLanByPortStpGroupMaxAge	1.3.6.1.4.1.1991.1.1.3.2.1.1.7	INTEGER	read-write	dot1dStpBridgeMaxAge: From RFC1493(Bridge MIB). The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
TIM snVLanByPortStpHelloTime	1.3.6.1.4.1.1991.1.1.3.2.1.1.16	Timeout	read-only	dot1dStpHelloTime: From RFC1493(Bridge MIB). The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
I32 snVLanByPortStpHoldTime	1.3.6.1.4.1.1991.1.1.3.2.1.1.17	Integer32	read-only	dot1dStpHoldTime: From RFC1493(Bridge MIB). This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
TIM snVLanByPortStpMaxAge	1.3.6.1.4.1.1991.1.1.3.2.1.1.15	Timeout	read-only	dot1dStpMaxAge: From RFC1493(Bridge MIB). The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
INT snVLanByPortStpMode	1.3.6.1.4.1.1991.1.1.3.2.1.1.5	INTEGER	read-write	Spanning Tree Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. disable(0)...........no Spanning Tree enableStp(1).........activate Spanning Tree enableRstp(2)........activate Rapid Spanning Tree
INT snVLanByPortStpPriority	1.3.6.1.4.1.1991.1.1.3.2.1.1.6	INTEGER	read-write	dot1dStpPriority : The value of the write-able portion of the Stp ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of the base bridge address - dot1dBaseBridgeAddress.
INT snVLanByPortStpProtocolSpecification	1.3.6.1.4.1.1991.1.1.3.2.1.1.14	INTEGER	read-only	An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
I32 snVLanByPortStpRootCost	1.3.6.1.4.1.1991.1.1.3.2.1.1.21	Integer32	read-only	dot1dStpRootCost: From RFC1493(Bridge MIB). The cost of the path to the root as seen from this bridge.
I32 snVLanByPortStpRootPort	1.3.6.1.4.1.1991.1.1.3.2.1.1.22	Integer32	read-only	dot1dStpRootPort: From RFC1493(Bridge MIB). The port number of the port which offers the lowest cost path from this bridge to the root bridge.
TIK snVLanByPortStpTimeSinceTopologyChange	1.3.6.1.4.1.1991.1.1.3.2.1.1.19	TimeTicks	read-only	The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
C32 snVLanByPortStpTopChanges	1.3.6.1.4.1.1991.1.1.3.2.1.1.20	Counter32	read-only	The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
snVLanByPortTable	1.3.6.1.4.1.1991.1.1.3.2.1		not-accessible	If snSwGroupOperMode is configured as basic mode which is VLAN by Port, Layer2 switching, then this table is valid. Each VLAN switch port could have a number of VLAN IDs.
INT snVLanByPortVLanId	1.3.6.1.4.1.1991.1.1.3.2.1.1.2	INTEGER	read-write	The VLAN ID index to the VLAN By Port Info Table. Each VLAN Identifier can have a membership of multiple ports.
INT snVLanByPortVLanIndex	1.3.6.1.4.1.1991.1.1.3.2.1.1.1	INTEGER	read-only	The VLAN ID index must not be greater than the snVLanGroupVlanMaxEntry. Each VLAN Identifier can have a membership of multiple ports.
STR snVLanByPortVLanName	1.3.6.1.4.1.1991.1.1.3.2.1.1.25	DisplayString	read-write	VLAN Community Name string.
OCT snVLanByProtocolChassisDynamicMask	1.3.6.1.4.1.1991.1.1.3.2.2.1.11	OCTET STRING	read-only	The Chassis Protocol VLAN active port membership. (It was obsoleted after release 07100, replaced by snVLanByProtocolDynamicPortList)
OCT snVLanByProtocolChassisExcludeMask	1.3.6.1.4.1.1991.1.1.3.2.2.1.10	OCTET STRING	read-write	The Chassis Protocol VLAN port membership applied in exclusive mode. (It was obsoleted after release 07100, replaced by snVLanByProtocolExcludePortList)
OCT snVLanByProtocolChassisStaticMask	1.3.6.1.4.1.1991.1.1.3.2.2.1.9	OCTET STRING	read-write	The Chassis Protocol VLAN port membership applied in static mode. (It was obsoleted after release 07100, replaced by snVLanByProtocolStaticPortList)
INT snVLanByProtocolDynamic	1.3.6.1.4.1.1991.1.1.3.2.2.1.3	INTEGER	read-write	disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only.
POR snVLanByProtocolDynamicMask	1.3.6.1.4.1.1991.1.1.3.2.2.1.8	PortMask	read-only	The Standand-alone switch Protocol VLAN active port membership. (It was obsoleted for Chassis Product)
OCT snVLanByProtocolDynamicPortList	1.3.6.1.4.1.1991.1.1.3.2.2.1.15	OCTET STRING	read-only	A list of port indices which are dynamically joining the port membership of the Protocol VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
snVLanByProtocolEntry	1.3.6.1.4.1.1991.1.1.3.2.2.1		not-accessible	An entry in the VLAN By Protocol Configuration table.
POR snVLanByProtocolExcludeMask	1.3.6.1.4.1.1991.1.1.3.2.2.1.5	PortMask	read-write	The Standand-alone switch Protocol VLAN port membership applied in exclusive mode. (It was obsoleted for Chassis Product)
OCT snVLanByProtocolExcludePortList	1.3.6.1.4.1.1991.1.1.3.2.2.1.14	OCTET STRING	read-write	A list of port indices which are the excluded from port membership of the Protocol VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
INT snVLanByProtocolIndex	1.3.6.1.4.1.1991.1.1.3.2.2.1.2	INTEGER	read-only	The following IP/IPX protocol VLAN types are operated in Layer3 VLAN such as : ip(1), ipx(2), ipv6(7) The following are operated in Layer2 bridging such as: appleTalk(3), decNet(4), netBios(5), others(6) -- other protocols which are defined here.
INT snVLanByProtocolRouterIntf	1.3.6.1.4.1.1991.1.1.3.2.2.1.6	INTEGER	read-write	Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured.
INT snVLanByProtocolRowStatus	1.3.6.1.4.1.1991.1.1.3.2.2.1.7	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
POR snVLanByProtocolStaticMask	1.3.6.1.4.1.1991.1.1.3.2.2.1.4	PortMask	read-write	The Standand-alone switch Protocol VLAN port membership applied in static mode. (It was obsoleted for Chassis Product)
OCT snVLanByProtocolStaticPortList	1.3.6.1.4.1.1991.1.1.3.2.2.1.13	OCTET STRING	read-write	A list of port indices which are the configured port membership of the Protocol VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number.
snVLanByProtocolTable	1.3.6.1.4.1.1991.1.1.3.2.2		not-accessible	.
INT snVLanByProtocolVLanId	1.3.6.1.4.1.1991.1.1.3.2.2.1.1	INTEGER	read-only	The VLAN ID index to both of the VLAN By Port Info Table and this table.
STR snVLanByProtocolVLanName	1.3.6.1.4.1.1991.1.1.3.2.2.1.12	DisplayString	read-write	VLAN Community Name string.
snVLanCAR	1.3.6.1.4.1.1991.1.1.3.17
I32 snVLanGroupSetAllVLan	1.3.6.1.4.1.1991.1.1.3.1.7	Integer32	read-write	The value of this object is the VLanIndex of a particalur entry in snVLanByPortCfgTable (snVLanByPortCfgVLanId). All the attributes of that row of table except PortMask will be used to set the same attributes for the entire VLan group. VLanId and PortMask must be set for that particular entry prior to setting this object. Switch software will base on that VLAN information to set the entire VLAN. Note: All the intended attributes of the given row of the table (given VLAN) must be set prior setting this object. When this object is set, Set-All-VLAN action will take place simultaneously. The previous setting will be overwritten by the new one.
I32 snVLanGroupVlanCurEntryEx	1.3.6.1.4.1.1991.1.1.3.1.6	Integer32	read-only	The current total entry number of VLANs are configured.
I32 snVLanGroupVlanMaxEntry	1.3.6.1.4.1.1991.1.1.3.1.19	Integer32	read-write	The maximum number of VLAN entries that are allowed to configure. On NetIron products, This object will be implemented as read-only. Set request will be returned with not writable error. To set the maximum allowed vlan, use snAgentSysParaConfigEntry.
snVLanInfo	1.3.6.1.4.1.1991.1.1.3.2
snVsrp	1.3.6.1.4.1.1991.1.1.3.21
snWireless	1.3.6.1.4.1.1991.1.1.3.23

RFC description

Brocade (formerly Foundry Networks) MIB for managing switch group objects on SnSwitch family devices and related Brocade equipment.

Start monitoring Brocade/Foundry FastIron/BigIron Ethernet switch (VLAN/FDB/STP) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download FOUNDRY-SN-SWITCH-GROUP-MIB