FOUNDRY-SN-OSPF-GROUP-MIB

All MIBs › FOUNDRY-SN-OSPF-GROUP-MIB

Category: Protocol: OSPF, Technology: Routing, Vendor: Foundry/Brocade

Description: A Brocade Foundry MIB for FastIron routers covering OSPF configuration along with neighbor adjacency and LSA management.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is FOUNDRY-SN-OSPF-GROUP-MIB?

FOUNDRY-SN-OSPF-GROUP-MIB is a Brocade (formerly Foundry Networks) vendor module for FastIron and NetIron routers/Layer 3 switches, providing detailed OSPF routing protocol management beyond what the standard OSPF-MIB (RFC 1850) covers. It exposes general OSPF process configuration, per-area data, address-range route summarization, per-interface and virtual-interface OSPF state, and route redistribution settings. Its monitoring role is squarely in software/protocol status — tracking whether OSPF interfaces and virtual links are in the expected adjacency state and whether redistribution is behaving as configured — which is critical for diagnosing routing instability or lost adjacencies. It is designed to complement, not replace, the standard OSPF-MIB, adding Foundry/Brocade-specific extensions on top of it. It is deployed in enterprise and service-provider networks running Brocade/Foundry FastIron or NetIron OSPF routers, and the FOUNDRY-SN-OSPF-GROUP-MIB MIB is loaded alongside that standard OSPF-MIB rather than in place of it, giving Brocade/Foundry-specific visibility into area, interface, and redistribution state.

IPNetwork Monitor allows you to monitor SNMP objects defined in FOUNDRY-SN-OSPF-GROUP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ruckus (CommScope) ICX 8200 Series (2023) — current FastIron-based campus L2/L3 switch, direct successor line to Brocade/Foundry FastIron routers

Monitoring Examples

An admin would poll snOspfIntf entries to check per-interface OSPF state and snOspfVirtIf to confirm virtual-link status across a non-contiguous backbone area, alongside snOspfArea for area-level LSA information. A virtual interface stuck in a non-full adjacency state would reveal a broken OSPF path across an ABR, and unexpected entries in snOspfRedis would flag unintended route redistribution leaking routes between protocols.

What Can Be Monitored

OSPF general process configuration
OSPF area and LSA information
OSPF interface adjacency state
virtual interface/link status
route redistribution configuration
address range route summarization

Imported Objects

From FOUNDRY-SN-ROOT-MIB

snOspf

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress

OIDs

OID symbolic	OID numeric	Type	Access	Description
snOspfAddrRange	1.3.6.1.4.1.1991.1.2.4.3
RTR snOspfAdminStat	1.3.6.1.4.1.1991.1.2.4.1.2	RtrStatus	read-write	The administrative status of OSPF in the router. The value 'enabled' denotes that the OSPF Process is active on at least one interface; 'disabled' disables it on all interfaces.
snOspfArea	1.3.6.1.4.1.1991.1.2.4.2
snOspfAreaEntry	1.3.6.1.4.1.1991.1.2.4.2.1.1		not-accessible	Information describing the configured parameters and cumulative statistics of one of the router's attached areas.
ARE snOspfAreaId	1.3.6.1.4.1.1991.1.2.4.2.1.1.1	AreaID	read-only	A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.
INT snOspfAreaIdFormat	1.3.6.1.4.1.1991.1.2.4.2.1.1.5	INTEGER	read-write	This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
ARE snOspfAreaRangeAreaID	1.3.6.1.4.1.1991.1.2.4.3.1.1.1	AreaID	read-only	The Area the Address Range is to be found within.
INT snOspfAreaRangeAreaIdFormat	1.3.6.1.4.1.1991.1.2.4.3.1.1.5	INTEGER	read-only	This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
snOspfAreaRangeEntry	1.3.6.1.4.1.1991.1.2.4.3.1.1		not-accessible	A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255
IP snOspfAreaRangeMask	1.3.6.1.4.1.1991.1.2.4.3.1.1.3	IpAddress	read-write	The Subnet Mask that pertains to the Net or Subnet.
IP snOspfAreaRangeNet	1.3.6.1.4.1.1991.1.2.4.3.1.1.2	IpAddress	read-only	The IP Address of the Net or Subnet indicated by the range.
INT snOspfAreaRangeRowStatus	1.3.6.1.4.1.1991.1.2.4.3.1.1.4	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
snOspfAreaRangeTable	1.3.6.1.4.1.1991.1.2.4.3.1		not-accessible	A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255
INT snOspfAreaRowStatus	1.3.6.1.4.1.1991.1.2.4.2.1.1.4	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
snOspfAreaStatus	1.3.6.1.4.1.1991.1.2.4.11
GAU snOspfAreaStatusAreaBdrRtrCount	1.3.6.1.4.1.1991.1.2.4.11.1.1.6	Gauge	read-only	The total number of area border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
ARE snOspfAreaStatusAreaId	1.3.6.1.4.1.1991.1.2.4.11.1.1.2	AreaID	read-only	A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.
INT snOspfAreaStatusAreaIdFormat	1.3.6.1.4.1.1991.1.2.4.11.1.1.10	INTEGER	read-only	This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
GAU snOspfAreaStatusASBdrRtrCount	1.3.6.1.4.1.1991.1.2.4.11.1.1.7	Gauge	read-only	The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass.
snOspfAreaStatusEntry	1.3.6.1.4.1.1991.1.2.4.11.1.1		not-accessible	Information describing the configured parameters and cumulative statistics of one of the router's attached areas.
INT snOspfAreaStatusEntryIndex	1.3.6.1.4.1.1991.1.2.4.11.1.1.1	INTEGER	read-only	The table entry index of this Area.
INT snOspfAreaStatusImportASExtern	1.3.6.1.4.1.1991.1.2.4.11.1.1.3	INTEGER	read-only	The area's support for importing AS external link- state advertisements.
INT snOspfAreaStatusLSACksumSum	1.3.6.1.4.1.1991.1.2.4.11.1.1.9	INTEGER	read-only	The 32-bit unsigned sum of the link-state advertisements' LS checksums contained in this area's link-state database. This sum excludes external (LS type 5) link-state advertisements. The sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
GAU snOspfAreaStatusLSACount	1.3.6.1.4.1.1991.1.2.4.11.1.1.8	Gauge	read-only	The total number of link-state advertisements in this area's link-state database, excluding AS External LSA's.
CTR snOspfAreaStatusSpfRuns	1.3.6.1.4.1.1991.1.2.4.11.1.1.5	Counter	read-only	The number of times that the intra-area route table has been calculated using this area's link-state database. This is typically done using Dijkstra's algorithm.
BIG snOspfAreaStatusStubMetric	1.3.6.1.4.1.1991.1.2.4.11.1.1.4	BigMetric	read-only	The metric value applied at the default type of service(ospfMetric). By default, this equals the least metric at the type of service among the interfaces to other areas. This Object exist if only if the value of snOspfAreaSummary is snOspfAreaSummary(2); Otherwise, an SNMP_GET/GET_NEXT attempt of this Object will return NO_SUCH_NAME.
snOspfAreaStatusTable	1.3.6.1.4.1.1991.1.2.4.11.1		not-accessible	Information describing the configured parameters and cumulative statistics of the router's attached areas.
snOspfAreaTable	1.3.6.1.4.1.1991.1.2.4.2.1		not-accessible	Information describing the configured parameters and cumulative statistics of the router's attached areas.
TRU snOspfASBdrRtrStatus	1.3.6.1.4.1.1991.1.2.4.1.3	TruthVal	read-write	A flag to note whether this router is an Autonomous System border router.
INT snOspfConfigErrorType	1.3.6.1.4.1.1991.1.2.4.15.2	INTEGER	read-only	Potential types of configuration conflicts. Used by the ospfConfigError and ospfConfigVir- tError traps.
INT snOspfDefaultOspfMetricValue	1.3.6.1.4.1.1991.1.2.4.1.5	INTEGER	read-write	The metric of using a default OSPF Metric value on this route.
INT snOspfDistance	1.3.6.1.4.1.1991.1.2.4.1.15	INTEGER	read-write	OSPF Adminitrative distance. 0 if distance is not set.
INT snOspfDistanceExternal	1.3.6.1.4.1.1991.1.2.4.1.18	INTEGER	read-write	OSPF Adminitrative distance - External.
INT snOspfDistanceInter	1.3.6.1.4.1.1991.1.2.4.1.17	INTEGER	read-write	OSPF Adminitrative distance - Inter Area.
INT snOspfDistanceIntra	1.3.6.1.4.1.1991.1.2.4.1.16	INTEGER	read-write	OSPF Adminitrative distance - Intra Area.
INT snOspfExitOverflowInterval	1.3.6.1.4.1.1991.1.2.4.1.12	INTEGER	read-write	The number of seconds that, after entering OverflowState, a router will attempt to leave OverflowState. This allows the router to again originate non-default AS-external-LSAs. When set to 0, the router will not leave Overflow- State until restarted.
INT snOspfExternLSACksumSum	1.3.6.1.4.1.1991.1.2.4.1.7	INTEGER	read-only	The 32-bit unsigned sum of the LS checksums of the external link-state advertisements contained in the link-state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers.
GAU snOspfExternLSACount	1.3.6.1.4.1.1991.1.2.4.1.6	Gauge	read-only	The number of external (LS type 5) link-state advertisements in the link-state database.
snOspfExtLsdb	1.3.6.1.4.1.1991.1.2.4.10
OCT snOspfExtLsdbAdvertisement	1.3.6.1.4.1.1991.1.2.4.10.1.1.8	OCTET STRING	read-only	The entire Link State Advertisement, including its header.
INT snOspfExtLsdbAge	1.3.6.1.4.1.1991.1.2.4.10.1.1.6	INTEGER	read-only	This field is the age of the link state adver- tisement in seconds.
INT snOspfExtLsdbChecksum	1.3.6.1.4.1.1991.1.2.4.10.1.1.7	INTEGER	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
snOspfExtLsdbEntry	1.3.6.1.4.1.1991.1.2.4.10.1.1		not-accessible	A single Link State Advertisement.
INT snOspfExtLsdbEntryIndex	1.3.6.1.4.1.1991.1.2.4.10.1.1.1	INTEGER	read-only	The table entry index of this Link State Database.
INT snOspfExtLsdbLimit	1.3.6.1.4.1.1991.1.2.4.1.11	INTEGER	read-write	The maximum number of non-default AS- external-LSAs entries that can be stored in the link-state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches ospfExtLsdbLimit, the router enters Overflow- State. The router never holds more than ospfExtLsdbLimit non-default AS-external-LSAs in its database. OspfExtLsdbLimit MUST be set identically in all routers attached to the OSPF backbone and/or any regular OSPF area. (i.e., OSPF stub areas and NSSAs are excluded).
IP snOspfExtLsdbLsId	1.3.6.1.4.1.1991.1.2.4.10.1.1.3	IpAddress	read-only	The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
ROU snOspfExtLsdbRouterId	1.3.6.1.4.1.1991.1.2.4.10.1.1.4	RouterID	read-only	The 32 bit number that uniquely identifies the originating router in the Autonomous System.
INT snOspfExtLsdbSequence	1.3.6.1.4.1.1991.1.2.4.10.1.1.5	INTEGER	read-only	The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
snOspfExtLsdbTable	1.3.6.1.4.1.1991.1.2.4.10.1		not-accessible	The OSPF Process's Links State Database.
INT snOspfExtLsdbType	1.3.6.1.4.1.1991.1.2.4.10.1.1.2	INTEGER	read-only	The type of the link state advertisement. Each link state type has a separate advertise- ment format.
snOspfGen	1.3.6.1.4.1.1991.1.2.4.1
RTR snOspfIf2AdminStat	1.3.6.1.4.1.1991.1.2.4.4.2.1.3	RtrStatus	read-write	The OSPF interface's administrative status. The value 'enabled' denotes that neighbor relationships may be formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.
ARE snOspfIf2AreaId	1.3.6.1.4.1.1991.1.2.4.4.2.1.2	AreaID	read-write	A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
INT snOspfIf2AreaIdFormat	1.3.6.1.4.1.1991.1.2.4.4.2.1.16	INTEGER	read-only	This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
OCT snOspfIf2AuthKey	1.3.6.1.4.1.1991.1.2.4.4.2.1.10	OCTET STRING	read-write	The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, snOspfIf2AuthKey always returns an Octet String of length zero.
INT snOspfIf2AuthType	1.3.6.1.4.1.1991.1.2.4.4.2.1.9	INTEGER	read-write	The authentication type specified for an interface. Additional authentication types may be assigned locally on a per interface basis.
INT snOspfIf2DatabaseFilterAllOut	1.3.6.1.4.1.1991.1.2.4.4.2.1.18	INTEGER	read-write	This object control the filtering of outgoing OSPF LSA on this interface.
snOspfIf2Entry	1.3.6.1.4.1.1991.1.2.4.4.2.1		not-accessible	The OSPF Interface Entry describes one interface from the viewpoint of OSPF.
HEL snOspfIf2HelloInterval	1.3.6.1.4.1.1991.1.2.4.4.2.1.7	HelloRange	read-write	The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
INT snOspfIf2Md5ActivationWaitTime	1.3.6.1.4.1.1991.1.2.4.4.2.1.15	INTEGER	read-write	The md5 authentication key activation wait time is specified in second and the maximum wait time is 14400 seconds (4 hours).
OCT snOspfIf2Md5AuthKey	1.3.6.1.4.1.1991.1.2.4.4.2.1.14	OCTET STRING	read-write	The MD5 Authentication Key. If the Area's Authorization Type is md5, and the key length is shorter than 16 octets, the agent will left adjust and zero fill to 16 octets. When read, snOspfIf2Md5AuthKey always returns an Octet String of length zero.
INT snOspfIf2Md5AuthKeyId	1.3.6.1.4.1.1991.1.2.4.4.2.1.13	INTEGER	read-write	The md5 authentication key ID. If the snOspfVirtIfAuthType is set to md5, the value of snOspfIf2Md5AuthKeyId must be (1 to 255). This field identifies the algorithm and secret key used to create the message digest appended to the OSPF packet. Key Identifiers are unique per-interface (or equivalently, per-subnet).
INT snOspfIf2MetricValue	1.3.6.1.4.1.1991.1.2.4.4.2.1.11	INTEGER	read-write	The metric of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed.
INT snOspfIf2MtuIgnore	1.3.6.1.4.1.1991.1.2.4.4.2.1.19	INTEGER	read-write	This object control MTU detection mode of this interface.
INT snOspfIf2NetworkP2mp	1.3.6.1.4.1.1991.1.2.4.4.2.1.20	INTEGER	read-write	This object enable/disable P2MP mode of this interface.
INT snOspfIf2PassiveMode	1.3.6.1.4.1.1991.1.2.4.4.2.1.17	INTEGER	read-write	This object control the passive mode of this interface.
INT snOspfIf2Port	1.3.6.1.4.1.1991.1.2.4.4.2.1.1	INTEGER	read-only	The physical router port of this OSPF interface.
UPT snOspfIf2RetransInterval	1.3.6.1.4.1.1991.1.2.4.4.2.1.6	UpToMaxAge	read-write	The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets.
INT snOspfIf2RowStatus	1.3.6.1.4.1.1991.1.2.4.4.2.1.12	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
NUM snOspfIf2RtrDeadInterval	1.3.6.1.4.1.1991.1.2.4.4.2.1.8	PositiveInteger	read-write	The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
DES snOspfIf2RtrPriority	1.3.6.1.4.1.1991.1.2.4.4.2.1.4	DesignatedRouterPriority	read-write	The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.
snOspfIf2Table	1.3.6.1.4.1.1991.1.2.4.4.2		not-accessible	The OSPF Interface Table describes the interfaces from the viewpoint of OSPF.
UPT snOspfIf2TransitDelay	1.3.6.1.4.1.1991.1.2.4.4.2.1.5	UpToMaxAge	read-write	The estimated number of seconds it takes to transmit a link- state update packet over this interface.
RTR snOspfIfAdminStat	1.3.6.1.4.1.1991.1.2.4.4.1.1.3	RtrStatus	read-write	The OSPF interface's administrative status. The value 'enabled' denotes that neighbor relationships may be formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.
ARE snOspfIfAreaId	1.3.6.1.4.1.1991.1.2.4.4.1.1.2	AreaID	read-write	A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
INT snOspfIfAreaIdFormat	1.3.6.1.4.1.1991.1.2.4.4.1.1.16	INTEGER	read-only	This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
OCT snOspfIfAuthKey	1.3.6.1.4.1.1991.1.2.4.4.1.1.10	OCTET STRING	read-write	The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, snOspfIfAuthKey always returns an Octet String of length zero.
INT snOspfIfAuthType	1.3.6.1.4.1.1991.1.2.4.4.1.1.9	INTEGER	read-write	The authentication type specified for an interface. Additional authentication types may be assigned locally on a per interface basis.
INT snOspfIfDatabaseFilterAllOut	1.3.6.1.4.1.1991.1.2.4.4.1.1.18	INTEGER	read-write	This object control the filtering of outgoing OSPF LSA on this interface.
snOspfIfEntry	1.3.6.1.4.1.1991.1.2.4.4.1.1		not-accessible	The OSPF Interface Entry describes one interface from the viewpoint of OSPF.
HEL snOspfIfHelloInterval	1.3.6.1.4.1.1991.1.2.4.4.1.1.7	HelloRange	read-write	The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
INT snOspfIfMd5ActivationWaitTime	1.3.6.1.4.1.1991.1.2.4.4.1.1.15	INTEGER	read-write	The md5 authentication key activation wait time is specified in second and the maximum wait time is 14400 seconds (4 hours).
OCT snOspfIfMd5AuthKey	1.3.6.1.4.1.1991.1.2.4.4.1.1.14	OCTET STRING	read-write	The MD5 Authentication Key. If the Area's Authorization Type is md5, and the key length is shorter than 16 octets, the agent will left adjust and zero fill to 16 octets. When read, snOspfIfMd5AuthKey always returns an Octet String of length zero.
INT snOspfIfMd5AuthKeyId	1.3.6.1.4.1.1991.1.2.4.4.1.1.13	INTEGER	read-write	The md5 authentication key ID. If the snOspfVirtIfAuthType is set to md5, the value of snOspfIfMd5AuthKeyId must be (1 to 255). This field identifies the algorithm and secret key used to create the message digest appended to the OSPF packet. Key Identifiers are unique per-interface (or equivalently, per-subnet).
INT snOspfIfMetricValue	1.3.6.1.4.1.1991.1.2.4.4.1.1.11	INTEGER	read-write	The metric of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed.
INT snOspfIfMtuIgnore	1.3.6.1.4.1.1991.1.2.4.4.1.1.19	INTEGER	read-write	This object control MTU detection mode of this interface.
INT snOspfIfNetworkP2mp	1.3.6.1.4.1.1991.1.2.4.4.1.1.20	INTEGER	read-write	This object enable/disable P2MP mode of this interface.
INT snOspfIfPassiveMode	1.3.6.1.4.1.1991.1.2.4.4.1.1.17	INTEGER	read-write	This object control the passive mode of this interface.
INT snOspfIfPort	1.3.6.1.4.1.1991.1.2.4.4.1.1.1	INTEGER	read-only	The physical router port of this OSPF interface.
UPT snOspfIfRetransInterval	1.3.6.1.4.1.1991.1.2.4.4.1.1.6	UpToMaxAge	read-write	The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets.
INT snOspfIfRowStatus	1.3.6.1.4.1.1991.1.2.4.4.1.1.12	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
NUM snOspfIfRtrDeadInterval	1.3.6.1.4.1.1991.1.2.4.4.1.1.8	PositiveInteger	read-write	The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
DES snOspfIfRtrPriority	1.3.6.1.4.1.1991.1.2.4.4.1.1.4	DesignatedRouterPriority	read-write	The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.
snOspfIfStatus	1.3.6.1.4.1.1991.1.2.4.12
RTR snOspfIfStatusAdminStat	1.3.6.1.4.1.1991.1.2.4.12.1.1.6	RtrStatus	read-only	The OSPF interface's administrative status. The value 'enabled' denotes that neighbor relationships may be formed on the interface, and the interface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF.
ARE snOspfIfStatusAreaId	1.3.6.1.4.1.1991.1.2.4.12.1.1.4	AreaID	read-only	A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.
INT snOspfIfStatusAreaIdFormat	1.3.6.1.4.1.1991.1.2.4.12.1.1.22	INTEGER	read-only	This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
OCT snOspfIfStatusAuthKey	1.3.6.1.4.1.1991.1.2.4.12.1.1.17	OCTET STRING	read-only	The Authentication Key. If the Area's Authorization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. When read, snOspfIfStatusAuthKey always returns an Octet String of length zero.
INT snOspfIfStatusAuthType	1.3.6.1.4.1.1991.1.2.4.12.1.1.16	INTEGER	read-only	The authentication type specified for an interface. Additional authentication types may be assigned locally on a per interface basis.
IP snOspfIfStatusBackupDesignatedRouter	1.3.6.1.4.1.1991.1.2.4.12.1.1.14	IpAddress	read-only	The IP Address of the Backup Designated Router.
IP snOspfIfStatusDesignatedRouter	1.3.6.1.4.1.1991.1.2.4.12.1.1.13	IpAddress	read-only	The IP Address of the Designated Router.
snOspfIfStatusEntry	1.3.6.1.4.1.1991.1.2.4.12.1.1		not-accessible	The OSPF Interface Entry describes one interface from the viewpoint of OSPF.
INT snOspfIfStatusEntryIndex	1.3.6.1.4.1.1991.1.2.4.12.1.1.1	INTEGER	read-only	The table entry index of this Area.
CTR snOspfIfStatusEvents	1.3.6.1.4.1.1991.1.2.4.12.1.1.15	Counter	read-only	The number of times this OSPF interface has changed its state, or an error has occurred.
HEL snOspfIfStatusHelloInterval	1.3.6.1.4.1.1991.1.2.4.12.1.1.10	HelloRange	read-only	The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for all routers attached to a common network.
IP snOspfIfStatusIpAddress	1.3.6.1.4.1.1991.1.2.4.12.1.1.3	IpAddress	read-only	The IP address of this OSPF interface.
INT snOspfIfStatusMd5ActivationWaitTime	1.3.6.1.4.1.1991.1.2.4.12.1.1.21	INTEGER	read-only	The md5 authentication key activation wait time is specified in second and the maximum wait time is 14400 seconds (4 hours).
OCT snOspfIfStatusMd5AuthKey	1.3.6.1.4.1.1991.1.2.4.12.1.1.20	OCTET STRING	read-only	The MD5 Authentication Key. If the Area's Authorization Type is md5, and the key length is shorter than 16 octets, the agent will left adjust and zero fill to 16 octets. When read, snOspfIfMd5AuthKey always returns an Octet String of length zero.
INT snOspfIfStatusMd5AuthKeyId	1.3.6.1.4.1.1991.1.2.4.12.1.1.19	INTEGER	read-only	The md5 authentication key ID. If the snOspfVirtIfAuthType is set to md5, the value of snOspfIfMd5AuthKeyId must be (1 to 255). This field identifies the algorithm and secret key used to create the message digest appended to the OSPF packet. Key Identifiers are unique per-interface (or equivalently, per-subnet).
MET snOspfIfStatusMetricValue	1.3.6.1.4.1.1991.1.2.4.12.1.1.18	Metric	read-only	The metric of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed.
INT snOspfIfStatusPort	1.3.6.1.4.1.1991.1.2.4.12.1.1.2	INTEGER	read-only	The physical router port of this OSPF interface.
UPT snOspfIfStatusRetransInterval	1.3.6.1.4.1.1991.1.2.4.12.1.1.9	UpToMaxAge	read-only	The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets.
NUM snOspfIfStatusRtrDeadInterval	1.3.6.1.4.1.1991.1.2.4.12.1.1.11	PositiveInteger	read-only	The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network.
DES snOspfIfStatusRtrPriority	1.3.6.1.4.1.1991.1.2.4.12.1.1.7	DesignatedRouterPriority	read-only	The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligible to become the designated router on this particular network. In the event of a tie in this value, routers will use their router id as a tie breaker.
INT snOspfIfStatusState	1.3.6.1.4.1.1991.1.2.4.12.1.1.12	INTEGER	read-only	The OSPF Interface State.
snOspfIfStatusTable	1.3.6.1.4.1.1991.1.2.4.12.1		not-accessible	The OSPF Interface Status Table describes the interfaces from the viewpoint of OSPF.
UPT snOspfIfStatusTransitDelay	1.3.6.1.4.1.1991.1.2.4.12.1.1.8	UpToMaxAge	read-only	The estimated number of seconds it takes to transmit a link- state update packet over this interface.
INT snOspfIfStatusType	1.3.6.1.4.1.1991.1.2.4.12.1.1.5	INTEGER	read-only	The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broadcast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25, Frame Relay, and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'.
snOspfIfTable	1.3.6.1.4.1.1991.1.2.4.4.1		not-accessible	The OSPF Interface Table describes the interfaces from the viewpoint of OSPF.
UPT snOspfIfTransitDelay	1.3.6.1.4.1.1991.1.2.4.4.1.1.5	UpToMaxAge	read-write	The estimated number of seconds it takes to transmit a link- state update packet over this interface.
INT snOspfImportASExtern	1.3.6.1.4.1.1991.1.2.4.2.1.1.2	INTEGER	read-write	The area's support for importing AS external link- state advertisements. 0: Stub Area Type 1: Normal Area Type 2: NSSA Area Type
snOspfIntf	1.3.6.1.4.1.1991.1.2.4.4
snOspfLsdb	1.3.6.1.4.1.1991.1.2.4.9
OCT snOspfLsdbAdvertisement	1.3.6.1.4.1.1991.1.2.4.9.1.1.9	OCTET STRING	read-only	The entire Link State Advertisement, including its header.
INT snOspfLsdbAge	1.3.6.1.4.1.1991.1.2.4.9.1.1.7	INTEGER	read-only	This field is the age of the link state advertisement in seconds.
ARE snOspfLsdbAreaId	1.3.6.1.4.1.1991.1.2.4.9.1.1.2	AreaID	read-only	The 32 bit identifier of the Area from which the LSA was received.
INT snOspfLsdbAreaIdFormat	1.3.6.1.4.1.1991.1.2.4.9.1.1.10	INTEGER	read-only	This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
INT snOspfLsdbChecksum	1.3.6.1.4.1.1991.1.2.4.9.1.1.8	INTEGER	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
snOspfLsdbEntry	1.3.6.1.4.1.1991.1.2.4.9.1.1		not-accessible	A single Link State Advertisement.
INT snOspfLsdbEntryIndex	1.3.6.1.4.1.1991.1.2.4.9.1.1.1	INTEGER	read-only	The table entry index of this Link State Database.
IP snOspfLsdbLsId	1.3.6.1.4.1.1991.1.2.4.9.1.1.4	IpAddress	read-only	The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
ROU snOspfLsdbRouterId	1.3.6.1.4.1.1991.1.2.4.9.1.1.5	RouterID	read-only	The 32 bit number that uniquely identifies the originating router in the Autonomous System.
INT snOspfLsdbSequence	1.3.6.1.4.1.1991.1.2.4.9.1.1.6	INTEGER	read-only	The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
snOspfLsdbTable	1.3.6.1.4.1.1991.1.2.4.9.1		not-accessible	The OSPF Process's Links State Database.
INT snOspfLsdbType	1.3.6.1.4.1.1991.1.2.4.9.1.1.3	INTEGER	read-only	The type of the link state advertisement. Each link state type has a separate advertisement format.
snOspfNbr	1.3.6.1.4.1.1991.1.2.4.7
snOspfNbrEntry	1.3.6.1.4.1.1991.1.2.4.7.1.1		not-accessible	The information regarding a single neighbor.
INT snOspfNbrEntryIndex	1.3.6.1.4.1.1991.1.2.4.7.1.1.1	INTEGER	read-only	The table entry index of this neighbor.
CTR snOspfNbrEvents	1.3.6.1.4.1.1991.1.2.4.7.1.1.9	Counter	read-only	The number of times this neighbor relationship has changed state, or an error has occurred.
INT snOspfNbrIndex	1.3.6.1.4.1.1991.1.2.4.7.1.1.4	INTEGER	read-only	The neighbor index of each port and each IP address.
IP snOspfNbrIpAddr	1.3.6.1.4.1.1991.1.2.4.7.1.1.3	IpAddress	read-only	The IP address of this neighbor.
GAU snOspfNbrLsRetransQLen	1.3.6.1.4.1.1991.1.2.4.7.1.1.10	Gauge	read-only	The current length of the retransmission queue.
INT snOspfNbrOptions	1.3.6.1.4.1.1991.1.2.4.7.1.1.6	INTEGER	read-only	A Bit Mask corresponding to the neighbor's op- tions field. Bit 0, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 1, if set, indicates that the associated area accepts and operates on external informa- tion; if zero, it is a stub area. Bit 2, if set, indicates that the system is ca- pable of routing IP Multicast datagrams; i.e., that it implements the Multicast Extensions to OSPF. Bit 3, if set, indicates that the associated area is an NSSA. These areas are capable of carrying type 7 external advertisements, which are translated into type 5 external advertise- ments at NSSA borders.
INT snOspfNbrPort	1.3.6.1.4.1.1991.1.2.4.7.1.1.2	INTEGER	read-only	The physical port of this neighbor.
DES snOspfNbrPriority	1.3.6.1.4.1.1991.1.2.4.7.1.1.7	DesignatedRouterPriority	read-only	The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network.
ROU snOspfNbrRtrId	1.3.6.1.4.1.1991.1.2.4.7.1.1.5	RouterID	read-only	A 32-bit integer (represented as a type IpAddress) uniquely identifying the neighboring router in the Autonomous System.
INT snOspfNbrState	1.3.6.1.4.1.1991.1.2.4.7.1.1.8	INTEGER	read-only	The State of the relationship with this Neigh- bor.
snOspfNbrTable	1.3.6.1.4.1.1991.1.2.4.7.1		not-accessible	A table of non-virtual neighbor information.
CTR snOspfOriginateNewLSAs	1.3.6.1.4.1.1991.1.2.4.1.8	Counter	read-only	The number of new link-state advertisements that have been originated. This number is incremented each time the router originates a new LSA.
INT snOspfOspfRedisMetricType	1.3.6.1.4.1.1991.1.2.4.1.10	INTEGER	read-write	type1: For External Type 1 (comparable value) the intra-area and inter-area routes, it is an OSPF metric plus the External Metric. type2: For external Type 2 (non-comparable value) routes, it is the external metric.
IP snOspfPacketSrc	1.3.6.1.4.1.1991.1.2.4.15.4	IpAddress	read-only	The IP address of an inbound packet that can- not be identified by a neighbor instance.
INT snOspfPacketType	1.3.6.1.4.1.1991.1.2.4.15.3	INTEGER	read-only	OSPF packet types.
snOspfRedis	1.3.6.1.4.1.1991.1.2.4.6
INT snOspfRedisAction	1.3.6.1.4.1.1991.1.2.4.6.1.1.4	INTEGER	read-write	The action to be taken if the route match this entry. noImport(0): - the route is NOT imported into OSPF Domain. import(1): - the route is imported into OSPF Domain as external type 2 route.
snOspfRedisEntry	1.3.6.1.4.1.1991.1.2.4.6.1.1		not-accessible	The OSPF Redistribution Entry specifies a particular RIP or Static route to be imported into the OSPF domain.
INT snOspfRedisIndex	1.3.6.1.4.1.1991.1.2.4.6.1.1.1	INTEGER	read-only	The destination IP address that associates with this particular route.
IP snOspfRedisIpAddress	1.3.6.1.4.1.1991.1.2.4.6.1.1.2	IpAddress	read-write	The destination IP address that associates with this particular route.
IP snOspfRedisMask	1.3.6.1.4.1.1991.1.2.4.6.1.1.3	IpAddress	read-write	The Subnet Mask that pertains to this route.
INT snOspfRedisMatchRipMetric	1.3.6.1.4.1.1991.1.2.4.6.1.1.8	INTEGER	read-write	The value indicates to which the route metric should match: disabled(0): - the route metric does NOT match the RIP metric field. enabled(1): - the route metric matches the RIP metric field.
RTR snOspfRedisMode	1.3.6.1.4.1.1991.1.2.4.1.4	RtrStatus	read-write	The Redistribution status of OSPF in the router. The value 'enabled' denotes that the OSPF Redistribution is active; 'disabled' disables it on the router.
MET snOspfRedisOspfMetricValue	1.3.6.1.4.1.1991.1.2.4.6.1.1.7	Metric	read-write	The metric of using OSPF Metric value on this route.
INT snOspfRedisProtocol	1.3.6.1.4.1.1991.1.2.4.6.1.1.5	INTEGER	read-write	The imported routes into OSPF domain is set in the following: rip(1): - the RIP route. all(2): - all protocol route. static(3): - the static route. bgp(4): - the BGP route. connected(5): - the connected route. isis(6): - the ISIS route.
INT snOspfRedisRipMetricValue	1.3.6.1.4.1.1991.1.2.4.6.1.1.9	INTEGER	read-write	The metric of using RIP Metric value (1 to 15 hops) on this route.
INT snOspfRedisRowStatus	1.3.6.1.4.1.1991.1.2.4.6.1.1.10	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
INT snOspfRedisSetOspfMetric	1.3.6.1.4.1.1991.1.2.4.6.1.1.6	INTEGER	read-write	The value indicates to which the route metric should match: disabled(0): - the route metric does NOT match the OSPF metric field. enabled(1): - the route metric matches the OSPF metric field.
snOspfRedisTable	1.3.6.1.4.1.1991.1.2.4.6.1		not-accessible	The OSPF Redistribution Table contains a list of routes that could be imported into the OSPF domain.
INT snOspfRfc1583Compatibility	1.3.6.1.4.1.1991.1.2.4.1.13	INTEGER	read-write	This allows the ospf routing either compatible with RFC1583 or RFC2178. enabled(1)........activate RFC1583 compatibility rather than RFC2178 disabled(0).......disable RFC1583 compatibility and compatible to RFC2178.
ROU snOspfRouterId	1.3.6.1.4.1.1991.1.2.4.1.1	RouterID	read-write	A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses.
INT snOspfRouterIdFormat	1.3.6.1.4.1.1991.1.2.4.1.14	INTEGER	read-write	This object is used to specify whether RouterId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
snOspfRoutingInfo	1.3.6.1.4.1.1991.1.2.4.14
snOspfRoutingInfoEntry	1.3.6.1.4.1.1991.1.2.4.14.1.1		not-accessible	Information about a single ABR/ASBR Routing entry.
INT snOspfRoutingInfoIndex	1.3.6.1.4.1.1991.1.2.4.14.1.1.1	INTEGER	read-only	The table entry index of this Routing entry.
ROU snOspfRoutingInfoNextHopRouterID	1.3.6.1.4.1.1991.1.2.4.14.1.1.4	RouterID	read-only	The router ID of the next hop destination router.
INT snOspfRoutingInfoOutgoingInterface	1.3.6.1.4.1.1991.1.2.4.14.1.1.5	INTEGER	read-only	The outgoing interface of the destination router.
ROU snOspfRoutingInfoRouterID	1.3.6.1.4.1.1991.1.2.4.14.1.1.2	RouterID	read-only	The Router ID of the destination router.
INT snOspfRoutingInfoRouterType	1.3.6.1.4.1.1991.1.2.4.14.1.1.3	INTEGER	read-only	The Router type of the destination router as the following: abr (1) -- area border router. asbr (2) -- autonomous sytem border router. abrANDasbr(3) -- area border and autonomous system border router.
snOspfRoutingInfoTable	1.3.6.1.4.1.1991.1.2.4.14.1		not-accessible	Information about this router's routing information.
CTR snOspfRxNewLSAs	1.3.6.1.4.1.1991.1.2.4.1.9	Counter	read-only	The number of link-state advertisements received determined to be new instantiations. This number does not include newer instantiations of self-originated link-state advertisements.
OCT snOspfSetTrap	1.3.6.1.4.1.1991.1.2.4.15.1	OCTET STRING	read-write	A four-octet string serving as a bit map for the trap events defined by the OSPF traps. This object is used to enable and disable specific OSPF traps where a 1 in the bit field represents enabled. The right-most bit (least significant) represents trap 0.
BIG snOspfStubMetric	1.3.6.1.4.1.1991.1.2.4.2.1.1.3	BigMetric	read-write	The metric value applied at the default type of service(ospfMetric). By default, this equals the least metric at the type of service among the interfaces to other areas. This Object exist if only if the value of snOspfAreaSummary is snOspfAreaSummary(2); Otherwise, an SNMP_GET/GET_NEXT attempt of this Object will return NO_SUCH_NAME.
snOspfTrapControl	1.3.6.1.4.1.1991.1.2.4.15
RTR snOspfTrapsGenerationMode	1.3.6.1.4.1.1991.1.2.4.15.5	RtrStatus	read-write	Indicates if the generation of any OSPF traps is permitted on the router. The value 'enabled' denotes that the OSPF Traps can be generated by the router; 'disabled' denotes that the OSPF Traps can not be generated by the router even when snOspfSetTrap indicates the generation of specific OSPF Traps. This object provides global control on the generation of ospf traps.
snOspfVirtIf	1.3.6.1.4.1.1991.1.2.4.5
ARE snOspfVirtIfAreaID	1.3.6.1.4.1.1991.1.2.4.5.1.1.1	AreaID	read-only	The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0
INT snOspfVirtIfAreaIdFormat	1.3.6.1.4.1.1991.1.2.4.5.1.1.13	INTEGER	read-only	This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
OCT snOspfVirtIfAuthKey	1.3.6.1.4.1.1991.1.2.4.5.1.1.8	OCTET STRING	read-write	If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 octets. When read, snOspfVifAuthKey always returns a string of length zero.
INT snOspfVirtIfAuthType	1.3.6.1.4.1.1991.1.2.4.5.1.1.7	INTEGER	read-write	The authentication type specified for an interface. Additional authentication types may be assigned locally on a per interface basis.
snOspfVirtIfEntry	1.3.6.1.4.1.1991.1.2.4.5.1.1		not-accessible	Information about a single Virtual Interface.
HEL snOspfVirtIfHelloInterval	1.3.6.1.4.1.1991.1.2.4.5.1.1.5	HelloRange	read-write	The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.
INT snOspfVirtIfMd5ActivationWaitTime	1.3.6.1.4.1.1991.1.2.4.5.1.1.12	INTEGER	read-write	The md5 authentication key activation wait time is specified in second and the maximum wait time is 14400 seconds (4 hours).
OCT snOspfVirtIfMd5AuthKey	1.3.6.1.4.1.1991.1.2.4.5.1.1.11	OCTET STRING	read-write	The MD5 Authentication Key. If the Area's Authorization Type is md5, and the key length is shorter than 16 octets, the agent will left adjust and zero fill to 16 octets. When read, snOspfIfMd5AuthKey always returns an Octet String of length zero.
INT snOspfVirtIfMd5AuthKeyId	1.3.6.1.4.1.1991.1.2.4.5.1.1.10	INTEGER	read-write	The md5 authentication key ID. If the snOspfVirtIfAuthType is set to md5, the value of snOspfVirtIfMd5AuthKeyId must be (1 to 255). This field identifies the algorithm and secret key used to create the message digest appended to the OSPF packet. Key Identifiers are unique per-interface (or equivalently, per-subnet).
ROU snOspfVirtIfNeighbor	1.3.6.1.4.1.1991.1.2.4.5.1.1.2	RouterID	read-only	The Router ID of the Virtual Neighbor.
UPT snOspfVirtIfRetransInterval	1.3.6.1.4.1.1991.1.2.4.5.1.1.4	UpToMaxAge	read-write	The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets. This value should be well over the expected round-trip time.
INT snOspfVirtIfRowStatus	1.3.6.1.4.1.1991.1.2.4.5.1.1.9	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
NUM snOspfVirtIfRtrDeadInterval	1.3.6.1.4.1.1991.1.2.4.5.1.1.6	PositiveInteger	read-write	The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.
snOspfVirtIfStatus	1.3.6.1.4.1.1991.1.2.4.13
ARE snOspfVirtIfStatusAreaID	1.3.6.1.4.1.1991.1.2.4.13.1.1.2	AreaID	read-only	The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0
INT snOspfVirtIfStatusAreaIdFormat	1.3.6.1.4.1.1991.1.2.4.13.1.1.15	INTEGER	read-only	This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
OCT snOspfVirtIfStatusAuthKey	1.3.6.1.4.1.1991.1.2.4.13.1.1.11	OCTET STRING	read-only	If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 octets. When read, snOspfVifAuthKey always returns a string of length zero.
INT snOspfVirtIfStatusAuthType	1.3.6.1.4.1.1991.1.2.4.13.1.1.10	INTEGER	read-only	The authentication type specified for an interface. Additional authentication types may be assigned locally on a per interface basis.
snOspfVirtIfStatusEntry	1.3.6.1.4.1.1991.1.2.4.13.1.1		not-accessible	Information about a single Virtual Interface.
INT snOspfVirtIfStatusEntryIndex	1.3.6.1.4.1.1991.1.2.4.13.1.1.1	INTEGER	read-only	The table entry index of this Area.
CTR snOspfVirtIfStatusEvents	1.3.6.1.4.1.1991.1.2.4.13.1.1.9	Counter	read-only	The number of state changes or error events on this Virtual Link.
HEL snOspfVirtIfStatusHelloInterval	1.3.6.1.4.1.1991.1.2.4.13.1.1.6	HelloRange	read-only	The length of time, in seconds, between the Hello packets that the router sends on the interface. This value must be the same for the virtual neighbor.
INT snOspfVirtIfStatusMd5ActivationWaitTime	1.3.6.1.4.1.1991.1.2.4.13.1.1.14	INTEGER	read-only	The md5 authentication key activation wait time is specified in second and the maximum wait time is 14400 seconds (4 hours).
OCT snOspfVirtIfStatusMd5AuthKey	1.3.6.1.4.1.1991.1.2.4.13.1.1.13	OCTET STRING	read-only	The MD5 Authentication Key. If the Area's Authorization Type is md5, and the key length is shorter than 16 octets, the agent will left adjust and zero fill to 16 octets. When read, snOspfIfMd5AuthKey always returns an Octet String of length zero.
INT snOspfVirtIfStatusMd5AuthKeyId	1.3.6.1.4.1.1991.1.2.4.13.1.1.12	INTEGER	read-only	The md5 authentication key ID. If the snOspfVirtIfAuthType is set to md5, the value of snOspfVirtIfMd5AuthKeyId must be (1 to 255). This field identifies the algorithm and secret key used to create the message digest appended to the OSPF packet. Key Identifiers are unique per-interface (or equivalently, per-subnet).
ROU snOspfVirtIfStatusNeighbor	1.3.6.1.4.1.1991.1.2.4.13.1.1.3	RouterID	read-only	The Router ID of the Virtual Neighbor.
UPT snOspfVirtIfStatusRetransInterval	1.3.6.1.4.1.1991.1.2.4.13.1.1.5	UpToMaxAge	read-only	The number of seconds between link-state advertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database description and link-state request packets. This value should be well over the expected round-trip time.
NUM snOspfVirtIfStatusRtrDeadInterval	1.3.6.1.4.1.1991.1.2.4.13.1.1.7	PositiveInteger	read-only	The number of seconds that a router's Hello packets have not been seen before it's neighbors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neighbor.
INT snOspfVirtIfStatusState	1.3.6.1.4.1.1991.1.2.4.13.1.1.8	INTEGER	read-only	The OSPF virtual interfaces states.
snOspfVirtIfStatusTable	1.3.6.1.4.1.1991.1.2.4.13.1		not-accessible	Information about this router's virtual interfaces.
UPT snOspfVirtIfStatusTransitDelay	1.3.6.1.4.1.1991.1.2.4.13.1.1.4	UpToMaxAge	read-only	The estimated number of seconds it takes to transmit a link- state update packet over this interface.
snOspfVirtIfTable	1.3.6.1.4.1.1991.1.2.4.5.1		not-accessible	Information about this router's virtual interfaces.
UPT snOspfVirtIfTransitDelay	1.3.6.1.4.1.1991.1.2.4.5.1.1.3	UpToMaxAge	read-write	The estimated number of seconds it takes to transmit a link- state update packet over this interface.
snOspfVirtNbr	1.3.6.1.4.1.1991.1.2.4.8
ARE snOspfVirtNbrArea	1.3.6.1.4.1.1991.1.2.4.8.1.1.2	AreaID	read-only	The Transit Area Identifier.
INT snOspfVirtNbrAreaIdFormat	1.3.6.1.4.1.1991.1.2.4.8.1.1.9	INTEGER	read-only	This object is used to specify whether AreaId is represented as IP Address or an Integer. The values that can be written are: integer(0).....as an integer. ipAddress(1)...as IP Address.
snOspfVirtNbrEntry	1.3.6.1.4.1.1991.1.2.4.8.1.1		not-accessible	Virtual neighbor information.
INT snOspfVirtNbrEntryIndex	1.3.6.1.4.1.1991.1.2.4.8.1.1.1	INTEGER	read-only	The table entry index of this virtual neighbor.
CTR snOspfVirtNbrEvents	1.3.6.1.4.1.1991.1.2.4.8.1.1.7	Counter	read-only	The number of times this virtual link has changed its state, or an error has occurred.
IP snOspfVirtNbrIpAddr	1.3.6.1.4.1.1991.1.2.4.8.1.1.4	IpAddress	read-only	The IP address this Virtual Neighbor is using.
GAU snOspfVirtNbrLSRetransQLen	1.3.6.1.4.1.1991.1.2.4.8.1.1.8	Gauge	read-only	The current length of the retransmission queue.
INT snOspfVirtNbrOptions	1.3.6.1.4.1.1991.1.2.4.8.1.1.5	INTEGER	read-only	A bit map corresponding to the neighbor's options field. Thus, Bit 1, if set, indicates that the neighbor supports Type of Service Routing; if zero, no metrics other than TOS 0 are in use by the neighbor.
ROU snOspfVirtNbrRtrId	1.3.6.1.4.1.1991.1.2.4.8.1.1.3	RouterID	read-only	A 32-bit integer uniquely identifying the neighboring router in the Autonomous System.
INT snOspfVirtNbrState	1.3.6.1.4.1.1991.1.2.4.8.1.1.6	INTEGER	read-only	The state of the Virtual Neighbor Relationship.
snOspfVirtNbrTable	1.3.6.1.4.1.1991.1.2.4.8.1		not-accessible	A table of virtual neighbor information.

RFC description

Brocade Foundry OSPF group MIB providing Open Shortest Path First configuration, neighbor adjacency, and LSA management for FastIron routers.

Start monitoring Brocade/Foundry FastIron/NetIron router/L3 switch (OSPF extensions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download FOUNDRY-SN-OSPF-GROUP-MIB

What Is FOUNDRY-SN-OSPF-GROUP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description