| OID symbolic | OID numeric | Type | Access | Description |
|---|
| enterasysESwitchMIB | 1.3.6.1.4.1.5624.1.2.10 | | | The Enterasys Networks Proprietary MIB module for
entities implementing the Extended Switch Objects. |
| etsysESwitchObjects | 1.3.6.1.4.1.5624.1.2.10.1 | | | |
| etsysESwitchParams | 1.3.6.1.4.1.5624.1.2.10.1.1 | | | |
| ENA etsysESwitchAdminStatus | 1.3.6.1.4.1.5624.1.2.10.1.1.1 | EnabledStatus | read-write | DURABLE:
The meanings of the values are:
enabled(1) - setting this object to enabled causes the
device to begin it's power up sequence and attempt to
enter its operational state. If the value of this object
was disabled, then the non-volatile value of this object
is changed to enabled. As part of the power up sequence,
the device's management parameters may or may not be
reset. (In other words, the device may go through the
equivalent of a reset or before returning to the online state.
If the device is capable of going directly from the disabled
state to the enabled state without resetting any of its
management parameters, then it may do so. Such action is
product specific.)
disabled(2) - setting this object to offline causes the
device to cease network activity and enter a quiescent
state. A disabled device must still be able to respond
to management messages.
The value enable(1) or disable(2) shall be stored
in non-volatile memory for the initial reset value
of this variable. The factory default NV value is enable(1). |
| etsysESwitchRateLimiting | 1.3.6.1.4.1.5624.1.2.10.1.2 | | | |
| etsysESwitchRateLimitingTable | 1.3.6.1.4.1.5624.1.2.10.1.2.1 | | not-accessible | This table allows rate limiting of multicast frames
received on bridge ports. A typical application of this
might be to limit a broadcast storm to the confines
of the LAN connected by the bridge.
All objects in this table must be saved across a system
reset and/or a power cycle. |
| etsysESwitchRateLimitingEntry | 1.3.6.1.4.1.5624.1.2.10.1.2.1.1 | | not-accessible | An Entry (conceptual row) in the RateLimiting Table.
A collection of objects containing information for
enabling and configuring RateLimiting. |
| T/F etsysESwitchRateLimitSwitch | 1.3.6.1.4.1.5624.1.2.10.1.2.1.1.1 | TruthValue | read-write | DURABLE:
By default, rate limiting will be disabled. It can be
enabled by setting this object to 'true(1)'. |
| U32 etsysESwitchRateLimit | 1.3.6.1.4.1.5624.1.2.10.1.2.1.1.2 | Unsigned32 | read-write | DURABLE:
This is the maximum number of rate-limited frames per second
that the bridge will forward per second. |
| etsysESwitchFilter | 1.3.6.1.4.1.5624.1.2.10.1.3 | | | |
| etsysESwitchAddrFilterTable | 1.3.6.1.4.1.5624.1.2.10.1.3.1 | | not-accessible | A list of interface entries. The number of entries is
given by ifNumber, defined in MIB-II. |
| etsysESwitchAddrFilterEntry | 1.3.6.1.4.1.5624.1.2.10.1.3.1.1 | | not-accessible | A collection of objects containing information for a
given interface. |
| T/F etsysESwitchAddressFilter | 1.3.6.1.4.1.5624.1.2.10.1.3.1.1.1 | TruthValue | read-write | DURABLE:
A switch that controls address filtering. When true,
the bridge purges the learned entries from its forwarding
database, stops its learning process, and forwards only
frames with destination and source addresses that have
been specified via management. |
| etsysESwitchProtocolObjects | 1.3.6.1.4.1.5624.1.2.10.1.4 | | | |
| etsysESwitchEtherTypeTable | 1.3.6.1.4.1.5624.1.2.10.1.4.1 | | not-accessible | A table for defining the meaning of the 'userEtherType' rows in the
etsysESwitchProtocolTable. |
| etsysESwitchEtherTypeEntry | 1.3.6.1.4.1.5624.1.2.10.1.4.1.1 | | not-accessible | Each row defines a particular EtherType that may be used as a basis
for protocol filtering and VLAN classification. |
| INT etsysESwitchEtherTypeIndex | 1.3.6.1.4.1.5624.1.2.10.1.4.1.1.1 | INTEGER | not-accessible | A number between 1 and N that identifies a table row, and that serves
to link entries in this table to those in etsysESwitchProtocolTable. |
| OCT etsysESwitchEtherTypeValue | 1.3.6.1.4.1.5624.1.2.10.1.4.1.1.2 | OCTET STRING | read-create | Defines an EtherType for use with etsysESwitchESwitchProtocolTable. |
| INT etsysESwitchEtherTypeStatus | 1.3.6.1.4.1.5624.1.2.10.1.4.1.1.3 | INTEGER | read-create | This object indicates the administrative status of this entry.
other(1) - This entry is currently in effect, but the conditions
under which it will remain so differ from the ones described
for the other enumeration values
invalid(2) - Writing this value invalidates the entry. The agent
may (but is not required to) delete the row.
permanent(3) - This entry is currently in use and will remain so
after the next reset of the bridge.
deleteOnReset(4) - This entry is currently in use and will remain
so until the next reset of the bridge. |
| T/F etsysESwitchEtherTypePreempted | 1.3.6.1.4.1.5624.1.2.10.1.4.1.1.4 | TruthValue | read-only | If true, indicates that the switch has taken control of this row and
its associated resources (e.g., to support 802.1x authentication). |
| etsysESwitchProtocolTable | 1.3.6.1.4.1.5624.1.2.10.1.4.2 | | not-accessible | A table for configuring, and obtaining information about, protocol-
based filtering and VLAN assignment. |
| etsysESwitchProtocolEntry | 1.3.6.1.4.1.5624.1.2.10.1.4.2.1 | | not-accessible | Each row in etsysESwitchProtocolTable holds filtering instructions,
or VLAN classification instructions, for one (port, protocol) pair. |
| INT etsysESwitchProtocolReceivePort | 1.3.6.1.4.1.5624.1.2.10.1.4.2.1.1 | INTEGER | not-accessible | Identifies the receive port to which the protocol filter is to be
applied. The value '0' (when allowed) represents 'all ports'. |
| INT etsysESwitchProtocolType | 1.3.6.1.4.1.5624.1.2.10.1.4.2.1.2 | INTEGER | not-accessible | Identifies the protocol type. The switch chip in the RoamAbout M2
can recognize nine predefined high-level protocol types, and up to
three user-defined EtherTypes. (Some or all EtherType filters may
be reserved for use in implementing other features.)
Protocol types are as follows:
userEtherType(1) - Packets whose Ethernet V2 EtherTypes or IEEE
802.3 LLC/SNAP EtherTypes match the user-defined EtherType
etsysESwitchEtherType[ etsysESwitchProtocolIndex ].
ipv4(2) - Internet Protocol version 4 carried in Ethernet V2
frames or IEEE 802.3 frames with LLC/SNAP headers. Also,
ARP packets carried in Ethernet V2 frames.
ipxEthernet(3) - IPX carried in Ethernet V2 frames.
ipxRaw(4) - IPX carried in IEEE 802.3 frames with no LLC.
ipxLlc(5) - IPX carried in IEEE 802.3 frames with LLC headers.
ipxSnap(6) - IPX carried in IEEE 802.3 frames with LLC/SNAP
headers.
sna(7) - SNA carried in IEEE 802.3 frames with LLC headers.
netBios(8) - NetBIOS carried in IEEE 802.3 frames with LLC
headers.
decnet(9) - DECnet carried in Ethernet V2 frames or in IEEE 802.3
frames with LLC/SNAP headers.
ipv6(10) - Internet Protocol version 6 carried in Ethernet V2
frames or IEEE 802.3 frames with LLC/SNAP headers |
| INT etsysESwitchProtocolIndex | 1.3.6.1.4.1.5624.1.2.10.1.4.2.1.3 | INTEGER | not-accessible | When etsysESwitchProtocolType indicates a user-defined protocol type,
this index should identify the corresponding protocol definition.
That is, to say, for a 'userEtherType' row, this index should point
to a row in the etsysESwitchEtherTypeTable.
When etsysESwitchProtocolType completely specifies the protocol type,
this index should be set to 1. |
| INT etsysESwitchProtocolConstraint | 1.3.6.1.4.1.5624.1.2.10.1.4.2.1.4 | INTEGER | read-create | Indicates what type of constraint the switch should apply to packets
caught by the (port, protocol) filter.
portMask(1) - Use the etsysESwitchProtocolAllowedToGoTo mask to
determine where the packets may be forwarded.
vlan(2) - Classify the packets as belonging to the VLAN
etsysESwitchProtocolVlanId.
Note that on the RoamAbout AccessPoint R2, port/protocol constraints
can sometimes take a back seat to other kinds of access controls. |
| POR etsysESwitchProtocolAllowedToGoTo | 1.3.6.1.4.1.5624.1.2.10.1.4.2.1.5 | PortList | read-create | A port mask object indicating where packets that match this row's
(port, protocol) filter are allowed to go.
It applies when etsysESwitchProtocolConstraint has the value
portMask(1) and this row is valid. |
| INT etsysESwitchProtocolVlanId | 1.3.6.1.4.1.5624.1.2.10.1.4.2.1.6 | INTEGER | read-create | A number identifying a VLAN to which packets that match this row's
(port, protocol) filter should be assigned.
It applies when etsysESwitchProtocolConstraint has the value vlan(2)
and this row is valid. |
| INT etsysESwitchProtocolStatus | 1.3.6.1.4.1.5624.1.2.10.1.4.2.1.7 | INTEGER | read-create | This object indicates the administrative status of this entry.
other(1) - This entry is currently in effect, but the conditions
under which it will remain so differ from the ones described
for the other enumeration values
invalid(2) - Writing this value to the object deletes the filter
or VLAN constraint. The agent may delete the SNMP table row
or return an AdminStatus of 'invalid' at its discretion.
permanent(3) - This entry is currently in use and will remain so
after the next reset of the bridge.
deleteOnReset(4) - This entry is currently in use and will remain
so until the next reset of the bridge. |
| T/F etsysESwitchProtocolPreempted | 1.3.6.1.4.1.5624.1.2.10.1.4.2.1.8 | TruthValue | read-only | If true, indicates that the switch has taken control of this row and
its associated resources (e.g., to support 802.1x authentication). |
| etsysESwitchConformance | 1.3.6.1.4.1.5624.1.2.10.2 | | | |
| etsysESwitchGroups | 1.3.6.1.4.1.5624.1.2.10.2.1 | | | |
| etsysESwitchBaseGroup | 1.3.6.1.4.1.5624.1.2.10.2.1.1 | | | The basic etsysESwitch objects. |
| etsysESwitchEtherTypeGroup | 1.3.6.1.4.1.5624.1.2.10.2.1.2 | | | A collection of objects for configuring user-defined EtherTypes. |
| etsysESwitchProtocolGroup | 1.3.6.1.4.1.5624.1.2.10.2.1.3 | | | A collection of objects for configuring protocol-based filtering. |
| etsysESwitchCompliances | 1.3.6.1.4.1.5624.1.2.10.2.2 | | | |
| etsysESwitchCompliance | 1.3.6.1.4.1.5624.1.2.10.2.2.1 | | | The compliance statement for devices that support
Extended Switch. |
