E5-110-AS-ATM-MIB

All MIBs › E5-110-AS-ATM-MIB

Category: ATM, Domain: DSL/xPON, Protocol: ATM, Vendor: Calix

Description: ATM service management MIB for the Calix E5-110 access system defining ATM interface and connection objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is E5-110-AS-ATM-MIB?

E5-110-AS-ATM-MIB is Calix's MIB for the E5-110 access system, defining objects for managing ATM interfaces and connections on that broadband access platform. As a vendor-specific ATM management module, it would be expected to expose ATM interface configuration and virtual path/channel connection (PVC) status, consistent with the ATM service focus stated in its short description, though no module description or sample objects were available to confirm exact object names. Its monitoring relevance, typical of ATM interface MIBs, centers on connection and interface software/status data - whether a given ATM PVC or interface is up, and basic traffic/cell statistics - rather than deep hardware sensors like temperature or power, though this can't be confirmed from the available data. It would naturally depend on the standard IETF ATM-MIB and IF-MIB conventions for representing ATM interfaces and connections, since vendor ATM MIBs commonly extend rather than replace those base models. It would be deployed in Calix E5-110 access system deployments providing ATM-based broadband access services to subscribers. Network engineers evaluating or troubleshooting this functionality can download the E5-110-AS-ATM-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in E5-110-AS-ATM-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Calix E5-110 access system

Monitoring Examples

No module description or sample object/table names were provided for this MIB, so a concrete polling scenario grounded in real identifiers can't be given honestly. Based on its stated ATM service-management scope, an operator would typically be expected to check ATM interface and PVC (permanent virtual connection) operational status to detect a subscriber-facing ATM connection that has gone down, but the specific object names for this module are unknown.

What Can Be Monitored

ATM interface status
ATM PVC/connection status

Imported Objects

From E5-110-MIB

accessSwitchCommonATM

OBJECT-IDENTITY

From Q-BRIDGE-MIB

PortList
VlanIndex

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter

From RFC1213-MIB

DisplayString
ifIndex

From SNMPv2-SMI

Unsigned32

From SNMPv2-TC

RowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT asMaxNumOfChannels	1.3.6.1.4.1.6321.1.2.3.1.99.1	INTEGER	read-only	The maximum number of virtual channels which can be created on a port.
asChannelTable	1.3.6.1.4.1.6321.1.2.3.1.99.2		not-accessible	This table includes the configuration of the virtual channel.
asChannelEntry	1.3.6.1.4.1.6321.1.2.3.1.99.2.1		not-accessible	An entry in asChannelTable.
INT asChannelVpi	1.3.6.1.4.1.6321.1.2.3.1.99.2.1.1	INTEGER	not-accessible	VPI of the channel.
INT asChannelVci	1.3.6.1.4.1.6321.1.2.3.1.99.2.1.2	INTEGER	not-accessible	VCI of the channel.
VLA asChannelPvid	1.3.6.1.4.1.6321.1.2.3.1.99.2.1.3	VlanIndex	read-create	The default VID of the channel.
INT asChannelPriority	1.3.6.1.4.1.6321.1.2.3.1.99.2.1.5	INTEGER	read-create	The 802.1p default priority of the channel.
STR asChannelProfile	1.3.6.1.4.1.6321.1.2.3.1.99.2.1.6	DisplayString	read-create	The value of this object identifies the row in the asChannelProfileTable, which applies for this channel.
ROW asChannelRowStatus	1.3.6.1.4.1.6321.1.2.3.1.99.2.1.7	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
INT asMaxNumOfChannelProfiles	1.3.6.1.4.1.6321.1.2.3.1.99.3	INTEGER	read-only	The maximum number of channel profiles which the system supports.
asChannelProfileTable	1.3.6.1.4.1.6321.1.2.3.1.99.6		not-accessible	This table contains information on the virtual channel configuration. One entry in this table reflects a profile which can be used to configure the virtual channel.
asChannelProfileEntry	1.3.6.1.4.1.6321.1.2.3.1.99.6.1		not-accessible	An entry in asChannelProfileTable.
STR asChannelProfileName	1.3.6.1.4.1.6321.1.2.3.1.99.6.1.1	DisplayString	not-accessible	This object is used by the channel profile table in order to identify a row of this table.
INT asChannelProfileEncap	1.3.6.1.4.1.6321.1.2.3.1.99.6.1.2	INTEGER	read-create	RFC1483 encapsulation.
INT asChannelProfileAAL	1.3.6.1.4.1.6321.1.2.3.1.99.6.1.3	INTEGER	read-create	ATM Adaptation Layer policy.
INT asChannelProfileClass	1.3.6.1.4.1.6321.1.2.3.1.99.6.1.4	INTEGER	read-create	ATM traffic class, including constant bit rate, real-time variable bit rate, non real-time variable bit rate, unspecified bit rate, and available bit rate.
U32 asChannelProfilePcr	1.3.6.1.4.1.6321.1.2.3.1.99.6.1.5	Unsigned32	read-create	Peak cell rate (cells/sec).
INT asChannelProfileCdvt	1.3.6.1.4.1.6321.1.2.3.1.99.6.1.6	INTEGER	read-create	Cell delay variation tolerance.
U32 asChannelProfileScrMcr	1.3.6.1.4.1.6321.1.2.3.1.99.6.1.7	Unsigned32	read-create	Sustain cell rate for vbr traffic class, or minimum cell rate for abr traffic class. The unit is the number of cells per second.
INT asChannelProfileBt	1.3.6.1.4.1.6321.1.2.3.1.99.6.1.8	INTEGER	read-create	Burst tolerance for vbr traffic class.
ROW asChannelProfileRowStatus	1.3.6.1.4.1.6321.1.2.3.1.99.6.1.9	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
asChannelStatusTable	1.3.6.1.4.1.6321.1.2.3.1.99.7		not-accessible	This table includes the status of the virtual channel.
asChannelStatusEntry	1.3.6.1.4.1.6321.1.2.3.1.99.7.1		not-accessible	An entry in asChannelStatusTable.
CTR asChannelTxPackets	1.3.6.1.4.1.6321.1.2.3.1.99.7.1.1	Counter	read-only	Count of channel Tx packets.
CTR asChannelRxPackets	1.3.6.1.4.1.6321.1.2.3.1.99.7.1.2	Counter	read-only	Count of channel Rx packets.
CTR asChannelTxCells	1.3.6.1.4.1.6321.1.2.3.1.99.7.1.3	Counter	read-only	Count of channel Tx cells.
CTR asChannelRxCells	1.3.6.1.4.1.6321.1.2.3.1.99.7.1.4	Counter	read-only	Count of channel Rx cells.
INT asMaxNumOfIpqosProfiles	1.3.6.1.4.1.6321.1.2.3.1.99.8	INTEGER	read-only	The maximum number of ipqos profiles which the system supports.
asIpqosProfileTable	1.3.6.1.4.1.6321.1.2.3.1.99.9		not-accessible	This table contains information on the ipqos profile configuration. One entry in this table reflects a profile which can be used to configure the virtual channel.
asIpqosProfileEntry	1.3.6.1.4.1.6321.1.2.3.1.99.9.1		not-accessible	An entry in asIpqosProfileTable.
STR asIpqosProfileName	1.3.6.1.4.1.6321.1.2.3.1.99.9.1.1	DisplayString	read-only	This object is used by the ipqos profile table in order to identify a row of this table.
INT asIpqosProfileEncap	1.3.6.1.4.1.6321.1.2.3.1.99.9.1.2	INTEGER	read-write	RFC1483 encapsulation.
INT asIpqosProfileQueueNumber	1.3.6.1.4.1.6321.1.2.3.1.99.9.1.3	INTEGER	read-write	Number of Ipqos profile egress queue.
ROW asIpqosProfileRowStatus	1.3.6.1.4.1.6321.1.2.3.1.99.9.1.4	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table.
asIpqosProfileQueueTable	1.3.6.1.4.1.6321.1.2.3.1.99.10		not-accessible	This table contains information on the ipqos profile queue configuration.
asIpqosProfileQueueEntry	1.3.6.1.4.1.6321.1.2.3.1.99.10.1		not-accessible	An entry in asIpqosProfileTable.
INT asIpqosProfileQueueIndex	1.3.6.1.4.1.6321.1.2.3.1.99.10.1.1	INTEGER	read-only	The index of a ipqos profile egress queue.
INT asIpqosProfileAAL	1.3.6.1.4.1.6321.1.2.3.1.99.10.1.2	INTEGER	read-write	ATM Adaptation Layer policy.
INT asIpqosProfileLevel	1.3.6.1.4.1.6321.1.2.3.1.99.10.1.3	INTEGER	read-write	ATM traffic class, including constant bit rate, real-time variable bit rate, non real-time variable bit rate, and unspecified bit rate.
U32 asIpqosProfileRate	1.3.6.1.4.1.6321.1.2.3.1.99.10.1.4	Unsigned32	read-write	Peak cell rate (cells/sec).
INT asShapingMode	1.3.6.1.4.1.6321.1.2.3.1.99.11	INTEGER	read-write	The two types of shaping mechanism can not co-exist, and this variable is used to switch between these two types of shaping mechanism. To change to new shaping mode, E5-11x will remove all configured PVC, save current configuration and reboot automatically. After reboot, the new shaping mode can take effect.

RFC description

Manages ATM virtual channel configuration and statistics on Zhone E5-110 access switch ports.

Start monitoring Calix E5-110 access system (ATM interfaces/PVCs) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download E5-110-AS-ATM-MIB

What Is E5-110-AS-ATM-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description