DLINKSW-GVRP-MIB

All MIBs › DLINKSW-GVRP-MIB

Organization: D-Link Corp.

Last Updated: 2013-04-17

Category: VLAN Management

Description: Manages GARP VLAN Registration Protocol (GVRP) operation on D-Link switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DLINKSW-GVRP-MIB?

This D-Link switch MIB manages GARP VLAN Registration Protocol (GVRP), a Layer 2 protocol that dynamically propagates VLAN membership information across switch trunk ports. No sample object names were provided in this extraction, so specific table/column names cannot be enumerated, but the described purpose is GVRP configuration. This is chiefly a protocol-configuration MIB, exposing GVRP enable state and timer parameters analogous to the GMRP timer model seen in related D-Link MIBs, rather than hardware sensor data. It conceptually builds on the IEEE 802.1Q GVRP standard, implemented here as a D-Link private extension since GVRP predates a formal IETF MIB in this vendor's product line. It is typically deployed on D-Link switches in networks that dynamically propagate VLAN configuration across multiple switches without manual per-switch VLAN entry, making DLINKSW-GVRP-MIB SNMP monitoring a standard part of maintaining that dynamic VLAN propagation.

IPNetwork Monitor allows you to monitor SNMP objects defined in DLINKSW-GVRP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

D-Link switch (general D-Link managed switch line)

Monitoring Examples

No sample_objects were supplied for this MIB, so a concrete object-level monitoring scenario cannot be honestly constructed; typically such a MIB would let an admin verify GVRP enable state and per-port join/leave timer values, analogous to the DLINK-3100-GMRP-MIB timer model, but exact object names cannot be confirmed here.

Imported Objects

From BRIDGE-MIB

dot1dBasePort

OBJECT-TYPE

From DLINK-ID-REC-MIB

dlinkIndustrialCommon

OBJECT-IDENTITY

From DLINKSW-TC-MIB

Dlink2kVlanList

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
dlinkSwGvrpMIB	1.3.6.1.4.1.171.26.33			This MIB module defines objects for GVRP.
dGvrpMIBNotifications	1.3.6.1.4.1.171.26.33.0
dGvrpMIBObjects	1.3.6.1.4.1.171.26.33.1
dGvrpGlobalMgmt	1.3.6.1.4.1.171.26.33.1.1
T/F dGvrpDynamicVlanCreation	1.3.6.1.4.1.171.26.33.1.1.1	TruthValue	read-write	This object indicates whether dynamic VLAN creation is enabled.
INT dGvrpNniGvrpBpduAddress	1.3.6.1.4.1.171.26.33.1.1.2	INTEGER	read-write	This object indicates the GVRP BPDU address in service provider site. 'dot1d' - The GVRP BPDU protocol address is 802.1d GVRP address: 01:80:CC:00:00:21 'dot1ad' - The GVRP BPDU protocol address is 802.1ad GVRP address: 01:80:CC:00:00:0D
dGvrpInterface	1.3.6.1.4.1.171.26.33.1.2
dGvrpInterfaceTable	1.3.6.1.4.1.171.26.33.1.2.1		not-accessible	This table contains the interface-specific GVRP parameters.
dGvrpInterfaceEntry	1.3.6.1.4.1.171.26.33.1.2.1.1		not-accessible	An entry indicates the GVRP parameters for a port/port-channel.
DLI dGvrpIfAdvertiseVlanLstFirst2K	1.3.6.1.4.1.171.26.33.1.2.1.1.1	Dlink2kVlanList	read-write	This object specifies the VLANs in a string of octets containing one bit per VLAN for VLANs 1 to 2048. If the bit is set to '1', then the VLAN is allowed to be advertised by the GVRP protocol on the interface.
DLI dGvrpIfAdvertiseVlanLstSecond2K	1.3.6.1.4.1.171.26.33.1.2.1.1.2	Dlink2kVlanList	read-write	This object specifies the VLANs in a string of octets containing one bit per VLAN for VLANs 2049 to 4094. If the bit is set to '1', then the VLAN is allowed to be advertised by the GVRP protocol on the interface.
DLI dGvrpIfForbiddenVlanLstFirst2K	1.3.6.1.4.1.171.26.33.1.2.1.1.3	Dlink2kVlanList	read-write	This object specifies the VLANs in a string of octets containing one bit per VLAN for VLANs 1 to 2048. If the bit is set to '1', then the interface is forbidden to be the VLAN's member.
DLI dGvrpIfForbiddenVlanLstSecond2K	1.3.6.1.4.1.171.26.33.1.2.1.1.4	Dlink2kVlanList	read-write	This object specifies the VLANs in a string of octets containing one bit per VLAN for VLANs 2049 to 4094. If the bit is set to '1', then the interface is forbidden to be the VLAN's member.
dGvrpStatistics	1.3.6.1.4.1.171.26.33.1.3
INT dGvrpClearAllStatistics	1.3.6.1.4.1.171.26.33.1.3.1	INTEGER	read-write	This object is used to clear GVRP statistics on all interfaces when set to 'clear'. No action is taken if this object is set to 'noOp'. When read, the value 'noOp' is returned.
dGvrpIfStatisticsTable	1.3.6.1.4.1.171.26.33.1.3.2		not-accessible	This table contains the statistics for GVRP capable ports.
dGvrpIfStatisticsEntry	1.3.6.1.4.1.171.26.33.1.3.2.1		not-accessible	An entry represents the statistics of a GVRP capable port.
U32 dGvrpIfStatRxJoinEmpty	1.3.6.1.4.1.171.26.33.1.3.2.1.1	Unsigned32	read-only	This object indicates the number of GVRP JoinEmpty message received on the interface.
U32 dGvrpIfStatRxJoinIn	1.3.6.1.4.1.171.26.33.1.3.2.1.2	Unsigned32	read-only	This object indicates the number of GVRP JoinIn message received on the interface.
U32 dGvrpIfStatRxLeaveEmpty	1.3.6.1.4.1.171.26.33.1.3.2.1.3	Unsigned32	read-only	This object indicates the number of GVRP LeaveEmpty message received on the interface.
U32 dGvrpIfStatRxLeaveIn	1.3.6.1.4.1.171.26.33.1.3.2.1.4	Unsigned32	read-only	This object indicates the number of GVRP LeaveIn message received on the interface.
U32 dGvrpIfStatRxLeaveAll	1.3.6.1.4.1.171.26.33.1.3.2.1.5	Unsigned32	read-only	This object indicates the number of GVRP LeaveAll message received on the interface.
U32 dGvrpIfStatRxEmpty	1.3.6.1.4.1.171.26.33.1.3.2.1.6	Unsigned32	read-only	This object indicates the number of GVRP Empty message received on the interface.
U32 dGvrpIfStatTxJoinEmpty	1.3.6.1.4.1.171.26.33.1.3.2.1.7	Unsigned32	read-only	This object indicates the number of GVRP JoinEmpty message transmitted on the interface.
U32 dGvrpIfStatTxJoinIn	1.3.6.1.4.1.171.26.33.1.3.2.1.8	Unsigned32	read-only	This object indicates the number of GVRP JoinIn message transmitted on the interface.
U32 dGvrpIfStatTxLeaveEmpty	1.3.6.1.4.1.171.26.33.1.3.2.1.9	Unsigned32	read-only	This object indicates the number of GVRP LeaveEmpty message transmitted on the interface.
U32 dGvrpIfStatTxLeaveIn	1.3.6.1.4.1.171.26.33.1.3.2.1.10	Unsigned32	read-only	This object indicates the number of GVRP LeaveIn message transmitted on the interface.
U32 dGvrpIfStatTxLeaveAll	1.3.6.1.4.1.171.26.33.1.3.2.1.11	Unsigned32	read-only	This object indicates the number of GVRP LeaveAll message transmitted on the interface.
U32 dGvrpIfStatTxEmpty	1.3.6.1.4.1.171.26.33.1.3.2.1.12	Unsigned32	read-only	This object indicates the number of GVRP Empty message transmitted on the interface.
INT dGvrpIfStatClear	1.3.6.1.4.1.171.26.33.1.3.2.1.13	INTEGER	read-write	This object is used to clear GVRP statistics on the interface when set to 'clear'. No action is taken if this object is set to 'noOp'. When read, the value 'noOp' is returned.
dGvrpMIBConformance	1.3.6.1.4.1.171.26.33.2
dGvrpCompliances	1.3.6.1.4.1.171.26.33.2.1
dGvrpCompliance	1.3.6.1.4.1.171.26.33.2.1.1			The compliance statement for entities which implement the DLINKSW-GVRP-MIB.
dGvrpGroups	1.3.6.1.4.1.171.26.33.2.2
dGvrpBasicCfgGroup	1.3.6.1.4.1.171.26.33.2.2.1			A collection of objects configures basic GVRP functions.
dGvrpServiceProviderCfgGroup	1.3.6.1.4.1.171.26.33.2.2.2			A collection of objects configures GVRP in service provider site.
dGvrpStatisticsGroup	1.3.6.1.4.1.171.26.33.2.2.4			A collection of objects provides the management of GVRP statistics.

RFC description

GVRP (GARP VLAN Registration Protocol) management for dynamic VLAN creation and registration.

Start monitoring D-Link managed switch (GVRP dynamic VLAN registration) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DLINKSW-GVRP-MIB

What Is DLINKSW-GVRP-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description