CXR-TS-MIB

All MIBs › CXR-TS-MIB

Category: Vendor: Aastra

Description: Manages Aastra CXR terminal server configuration, serial port parameters, and remote access sessions.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CXR-TS-MIB?

CXR-TS-MIB is a vendor-specific MIB for Aastra's CXR terminal server product line, covering the remote-access/console-server technology area. It is expected to expose configuration of serial ports (baud rate, flow control, port naming) and management of remote access sessions established through those ports. Its monitoring value centers on device/software operational status - whether serial ports are active, what session is connected on a given port, and session state - which helps operators confirm that out-of-band or dial-up access paths to other equipment remain available and correctly configured. As a self-contained vendor MIB with no module description provided, any dependency on standard MIBs (such as the RS-232-MIB) is not confirmed from available data. It would typically be deployed in environments using Aastra CXR terminal servers to provide serial console access to routers, switches, or other network equipment in a data center or remote site. Engineers can download the CXR-TS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CXR-TS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Aastra CXR terminal server

Monitoring Examples

No sample_objects or module description were available for this MIB in the supplied data, so specific object or table names cannot be cited without inventing them. A plausible use, consistent with the module's product category, is polling per-port configuration and connection-status objects to confirm a given serial port is correctly bound to its target device and currently active. Because the source data here provides no concrete object names, this must remain a general description rather than a specific technical example.

What Can Be Monitored

serial port configuration
port connection/session status

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

IpAddress
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT acctRad1	1.3.6.1.4.1.1425.1040.2.1.26	INTEGER	read-write	Use Server Radius 1 for acct.
INT acctRad2	1.3.6.1.4.1.1425.1040.2.1.27	INTEGER	read-write	Use Server Radius 2 for acct.
INT afterSend	1.3.6.1.4.1.1425.1040.2.1.19	INTEGER	read-write	Time After Send(modem mode)
IP aliasIpAddress	1.3.6.1.4.1.1425.1040.2.1.3	IpAddress	read-write	Alias IP address
IP aliasIpNetmask	1.3.6.1.4.1.1425.1040.2.1.4	IpAddress	read-write	Alias IP netmask
INT authRad1	1.3.6.1.4.1.1425.1040.2.1.24	INTEGER	read-write	Use Server Radius 1 for auth.
INT authRad2	1.3.6.1.4.1.1425.1040.2.1.25	INTEGER	read-write	Use Server Radius 2 for auth.
INT authType	1.3.6.1.4.1.1425.1040.2.1.23	INTEGER	read-write	Authentication type
INT baudRate	1.3.6.1.4.1.1425.1040.2.1.6	INTEGER	read-write	Baud rate
INT beforeSend	1.3.6.1.4.1.1425.1040.2.1.18	INTEGER	read-write	Time Before Send(modem mode)
INT bootp	1.3.6.1.4.1.1425.1040.1.3	INTEGER	read-write	Bootp
INT bytesReceiveFromV24	1.3.6.1.4.1.1425.1040.3.1.1	INTEGER	read-only	Bytes received from V24
INT bytesSendToV24	1.3.6.1.4.1.1425.1040.3.1.2	INTEGER	read-only	Bytes send to V24
cxr	1.3.6.1.4.1.1425
NTF dtrDown	1.3.6.1.4.1.1425.0.1044			DTR DOWN
NTF dtrUp	1.3.6.1.4.1.1425.0.1043			DTR UP
OCT endMsg	1.3.6.1.4.1.1425.1040.2.1.16	OCTET STRING	read-only	End msg character
OCT ethernetAddress	1.3.6.1.4.1.1425.1040.1.7	OCTET STRING	read-only	Mac Address
INT flowControl	1.3.6.1.4.1.1425.1040.2.1.12	INTEGER	read-write	Flow Control
INT formFeed	1.3.6.1.4.1.1425.1040.2.1.28	INTEGER	read-write	LPD form Feed
INT ftpdService	1.3.6.1.4.1.1425.1040.1.8	INTEGER	read-write	FTPD Service
IP gatewayToRemote	1.3.6.1.4.1.1425.1040.2.1.10	IpAddress	read-write	Gateway to remote
INT httpdService	1.3.6.1.4.1.1425.1040.1.9	INTEGER	read-write	HTTPD Service
INT interFrame	1.3.6.1.4.1.1425.1040.2.1.17	INTEGER	read-write	Time Inter Frame(modem mode)
IP ipGateway	1.3.6.1.4.1.1425.1040.1.6	IpAddress	read-write	IP Gateway
IP ipNetmask	1.3.6.1.4.1.1425.1040.1.5	IpAddress	read-write	IP Netmask
INT ipServer	1.3.6.1.4.1.1425.1040.2.1.8	INTEGER	read-only	Server IP
IP mainIpAddress	1.3.6.1.4.1.1425.1040.1.4	IpAddress	read-write	IP address
modbusEntry	1.3.6.1.4.1.1425.1040.4.1		not-accessible	Slave index 1 to 16 possible
INT modbusMode	1.3.6.1.4.1.1425.1040.2.1.32	INTEGER	read-write	Modbus Mode
modbusTable	1.3.6.1.4.1.1425.1040.4		not-accessible	Master modbus table containing all the slave parameters table
INT modbusType	1.3.6.1.4.1.1425.1040.2.1.33	INTEGER	read-write	Modbus Type
INT mode	1.3.6.1.4.1.1425.1040.2.1.13	INTEGER	read-write	Fonctionnement
INT multiSession	1.3.6.1.4.1.1425.1040.2.1.22	INTEGER	read-write	multiSession
INT nameResolution	1.3.6.1.4.1.1425.1040.1.15	INTEGER	read-write	Names Resolution
IP nameServer1	1.3.6.1.4.1.1425.1040.1.16	IpAddress	read-write	Names Server 1
IP nameServer2	1.3.6.1.4.1.1425.1040.1.17	IpAddress	read-write	Names Server 1
INT nbParStop	1.3.6.1.4.1.1425.1040.2.1.7	INTEGER	read-write	Nb bits/Parity/Nb stop bits
portEntry	1.3.6.1.4.1.1425.1040.2.1		not-accessible	Port index 1 to 11 possible
INT portIndex	1.3.6.1.4.1.1425.1040.2.1.1	INTEGER	read-only	Port Index
INT portReset	1.3.6.1.4.1.1425.1040.2.1.34	INTEGER	read-write	Apply changes to port
portStatsEntry	1.3.6.1.4.1.1425.1040.3.1		not-accessible	Port index 1 to 11 possible
portStatsTable	1.3.6.1.4.1.1425.1040.3		not-accessible	A table containing all the statistics ports
portTable	1.3.6.1.4.1.1425.1040.2		not-accessible	A table containing all the ports
STR productName	1.3.6.1.4.1.1425.1040.1.1	DisplayString	read-only	Product Name
STR radiusSecret1	1.3.6.1.4.1.1425.1040.1.19	DisplayString	read-write	Secret for Radius Server 1
STR radiusSecret2	1.3.6.1.4.1.1425.1040.1.21	DisplayString	read-write	Secret for Radius Server 2
IP radiusServer1	1.3.6.1.4.1.1425.1040.1.18	IpAddress	read-write	Radius Server 1
IP radiusServer2	1.3.6.1.4.1.1425.1040.1.20	IpAddress	read-write	Radius Server 2
IP remoteIpAddress	1.3.6.1.4.1.1425.1040.2.1.9	IpAddress	read-write	Remote IP address
INT remoteTcpPort	1.3.6.1.4.1.1425.1040.2.1.11	INTEGER	read-write	remote TCP port
INT reset	1.3.6.1.4.1.1425.1040.1.24	INTEGER	read-write	Reset the TS
INT resetByButton	1.3.6.1.4.1.1425.1040.1.23	INTEGER	read-write	Reset by button Enable ot Disable
INT rxIdle	1.3.6.1.4.1.1425.1040.2.1.14	INTEGER	read-write	Rx Idle
IP secondGateway	1.3.6.1.4.1.1425.1040.2.1.30	IpAddress	read-write	Second Gateway
IP secondIpAddress	1.3.6.1.4.1.1425.1040.2.1.29	IpAddress	read-write	Second IP address
INT secondTcpPort	1.3.6.1.4.1.1425.1040.2.1.31	INTEGER	read-write	Second TCP port
NTF sessionStarted	1.3.6.1.4.1.1425.0.1041			Session Begin
NTF sessionStopped	1.3.6.1.4.1.1425.0.1042			Session End
STR siteName	1.3.6.1.4.1.1425.1040.1.22	DisplayString	read-write	String indetifier for TS
INT slaveHexaAddress	1.3.6.1.4.1.1425.1040.4.1.1	INTEGER	read-write	Modbus Hexadecimal address
IP slaveIPaddr	1.3.6.1.4.1.1425.1040.4.1.2	IpAddress	read-write	Modbus IP address
INT slaveIPport	1.3.6.1.4.1.1425.1040.4.1.3	INTEGER	read-write	Modbus IP Port
INT snmpdService	1.3.6.1.4.1.1425.1040.1.11	INTEGER	read-write	SNMPD Service
INT snmpTrap	1.3.6.1.4.1.1425.1040.1.12	INTEGER	read-write	SNMP Traps
IP snmpTrapAddr1	1.3.6.1.4.1.1425.1040.1.13	IpAddress	read-write	Trap IP Address
IP snmpTrapAddr2	1.3.6.1.4.1.1425.1040.1.14	IpAddress	read-write	Trap IP Address
INT statusDTR	1.3.6.1.4.1.1425.1040.3.1.3	INTEGER	read-only	DTR Status
system	1.3.6.1.4.1.1425.1040.1
INT tcpPort	1.3.6.1.4.1.1425.1040.2.1.2	INTEGER	read-write	TCP port
INT telnetdService	1.3.6.1.4.1.1425.1040.1.10	INTEGER	read-write	TELNETD Service
INT terminalType	1.3.6.1.4.1.1425.1040.2.1.21	INTEGER	read-write	Terminal Type
INT timeoutPAD	1.3.6.1.4.1.1425.1040.2.1.20	INTEGER	read-write	Timeout PAD(modem PAD)
INT timeoutRxTx	1.3.6.1.4.1.1425.1040.2.1.5	INTEGER	read-write	Timeout No rx/Tx Data(min)
ts	1.3.6.1.4.1.1425.1040
INT txIdle	1.3.6.1.4.1.1425.1040.2.1.15	INTEGER	read-write	Tx Idle
STR version	1.3.6.1.4.1.1425.1040.1.2	DisplayString	read-only	Revision

RFC description

Carrier/transport system management MIB for CXR device configuration and monitoring.

Start monitoring Aastra CXR terminal server with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CXR-TS-MIB

What Is CXR-TS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description