All MIBs › CXBOPIO-MIB
Category: Frame Relay, Network Interfaces, Vendor: Aastra
Description: Manages Aastra BOP I/O (Bit-Oriented Protocol I/O) module configuration for WAN framing and signaling.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is CXBOPIO-MIB?
CXBOPIO-MIB is a vendor-specific MIB from Aastra (formerly Memotec/ConvertedX) covering the BOP (Bit-Oriented Protocol) I/O module used on CX-series WAN access equipment. It exposes configuration and operational-state data for BOP ports, including clock source selection, data encoding, and idle-line conditioning used in framed/synchronous WAN links. In monitoring terms it is used chiefly for hardware/software status of the module: it lets an operator confirm the administrative versus operational settings of each BOP port are in sync and detect misconfiguration (e.g., clock source mismatches) that would cause line framing errors or loss of synchronization. It works alongside other Aastra CX enterprise MIBs (such as CXLapBD-MIB and CXISDN-MIB) that manage adjacent WAN protocol layers on the same chassis. It is typically deployed in legacy telecom/WAN access gear at branch offices or telco POPs, where the CXBOPIO-MIB MIB remains in use for monitoring bit-oriented synchronous framing on BOP ports.
IPNetwork Monitor allows you to monitor SNMP objects defined in CXBOPIO-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Aastra ConvertedX (CX) WAN access router
- Aastra BOP I/O interface module
Monitoring Examples
An administrator would poll bopSapOprTable and its columnar object bopSapOprPortClockSource alongside the corresponding entries in bopSapAdmTable to verify that the operational clock source matches the administratively configured one; a mismatch often indicates a misprovisioned port. bopSapOprPortDataEncoding and bopSapOprPortIdleCondition would be checked to confirm the line encoding and idle-fill pattern are correct for the attached circuit, since a wrong idle condition setting can cause the far end to see spurious framing errors. bopMibLevel is read once to determine which version of the MIB's object set the agent supports before polling further.
What Can Be Monitored
- BOP port clock source (admin vs operational)
- port data encoding
- line idle condition
- administrative vs operational port table state
- MIB support level
This MIB depends on
Related MIBs
Imported Objects
From CXProduct-SMI
| Alias | |
| cxBOPIO | OBJECT-IDENTITY |
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| NTF bopPortStatusChange | 1.3.6.1.4.1.495.2.1.6.36.0.1 | Indicates that the hardware port associated with the service access point has changed state. It has toggled between any of the states defined in object bopStatOprPortState. | ||
| NTF bopTxClockStatusChange | 1.3.6.1.4.1.495.2.1.6.36.0.2 | Indicates that the transmit clock at hardware port associated with the service access point has changed state. It has toggled between any of the states defined in object bopStatOprTxClockState. | ||
| bopSapOprTable | 1.3.6.1.4.1.495.2.1.6.36.1 | not-accessible | A table containing the current configuration information about each BOP/COP port. | |
| bopSapOprEntry | 1.3.6.1.4.1.495.2.1.6.36.1.1 | not-accessible | The configuration information for a specific BOP/COP port. | |
| INT bopSapOprNumber | 1.3.6.1.4.1.495.2.1.6.36.1.1.1 | INTEGER | read-only | Defines the SAP ID using 2,3 or 4 digits. The first digit (A) is the slot #, the second digit (B) is the port #, and the remaining digits (CD) are the channel #. If a 2 digit number is entered, digits CD are assumed to be 0 and are inserted automatically when reading object. If a 3 digit number is entered, digit C is assumed to be 0 and is inserted automatically when reading object. Ranges of Values for A: 1-7 for CX900, 1-4 for CX1000 Ranges of Values for B: 1-5 for CX900, 1-4 for CX1000 Ranges of Values for CD: 00-30 Default Value: not applicable |
| ALI bopSapOprAlias | 1.3.6.1.4.1.495.2.1.6.36.1.1.2 | Alias | read-only | Determines the active textual name uniquely identifying this port SAP. Range of Values: 0 - 16 alphanumeric characters beginning with a non-numeric character Default Value: undefined |
| INT bopSapOprProtocol | 1.3.6.1.4.1.495.2.1.6.36.1.1.3 | INTEGER | read-only | Determines if the port is HDLC or Bisync. Only HDLC is supported by ISDN and T1/E1 ports. Indicates in the operative configuration the type of bisync protocol used by the controllers of the port associated with this SAP. Options: hdlc bsc3270 = Bisync 3270 controllers borroughs = Borroughs controllers sperry = Sperry controllers bsc3780 = Bisync 2780/3780 controllers Default Value: hdlc |
| INT bopSapOprPortClockSource | 1.3.6.1.4.1.495.2.1.6.36.1.1.5 | INTEGER | read-only | Determines the active data clock source for this port. Options: internal (1): Tx and Rx clocks are internally generated external (2): Tx and Rx clocks are externally supplied on separate pins split (3): Tx clock is internally generated and Rx clock is externally supplied slave (4): Tx and Rx clocks are externally supplied on the same pins Note: Split clocking is not supported in CX900 slots 5, 6 and 7. Default Value: external (locked to internal for ISDN) |
| INT bopSapOprPortSpeed | 1.3.6.1.4.1.495.2.1.6.36.1.1.6 | INTEGER | read-only | Determines the input and output speed in bits per second for this port. Note: Meaningful only if 'bopSapOprPortClockSource' is 'internal' or 'split'. Ranges of Values: 375-2048000; limited to 1875-256000 for CX900 slots 5,6,7. Default Value: 64,000 |
| INT bopSapOprPortDuplex | 1.3.6.1.4.1.495.2.1.6.36.1.1.7 | INTEGER | read-only | Determines whether this port is communicating simultaneously in both directions (full-duplex) or alternates between directions (half-duplex). Not applicable for ISDN and T1/E1 ports. Options: half (1): half-duplex full (2): full-duplex Default Value: full |
| INT bopSapOprPortMaxFrameSize | 1.3.6.1.4.1.495.2.1.6.36.1.1.8 | INTEGER | read-only | Determines the active maximum frame size supported by this port. Ranges of Values: 32-9000 Default Value: 1,600 (512 for ISDN) |
| INT bopSapOprPortDataEncoding | 1.3.6.1.4.1.495.2.1.6.36.1.1.9 | INTEGER | read-only | Determines the active data formatting and encoding used by this port. Options: n/a (0): object is not applicable nrz (1): NRZ (locked for ISDN 'D' channel; ISDN 'B' channel can use only this value or NRZI-Space value) nrzi-mark (2): NRZI-Mark nrzi-space (3): NRZI-Space (ISDN 'B' channel can use only this value or NRZ value) Note: CX900 Slot/port/channel 51x-71x can use only NRZ or NRZI-Space. Default Value: nrz |
| INT bopSapOprPortIdleCondition | 1.3.6.1.4.1.495.2.1.6.36.1.1.10 | INTEGER | read-only | Determines the active idle line condition supported by this port. Options: flags (1): flags marks (2): marks as400 (3): AS400 Default Value: flags |
| INT bopSapOprPortPreAmbleLength | 1.3.6.1.4.1.495.2.1.6.36.1.1.11 | INTEGER | read-only | Determines the minimum number of flags or sync pairs that will be inserted between frames by the port's transmitter. For HDLC frames: A value of zero causes flag sharing between frames. A value of one means no flag sharing and zero flags inserted between frames. A value of two means no flag sharing and one flag inserted between frames. A value of three means no flag sharing and two flags inserted between frames. Etc. For Bisync frames: A value of zero or one causes one sync pair to be inserted between frames. A value of two causes two sync pairs to be inserted between frames. A value of three causes three sync pairs to be inserted between frames. Etc. Ranges of Values: 0 -16 Default Value: 1 |
| INT bopSapOprPortFlagSharing | 1.3.6.1.4.1.495.2.1.6.36.1.1.12 | INTEGER | read-only | Determines whether back-to-back Tx frames share opening and closing flag. This value is meaningful only if 'bopSapAdmPortPreAmbleLength' is set to zero. Options: disabled (1): back-to-back frames do not share flag enabled (2): back-to-back frames share flag Default Value: disabled |
| INT bopSapOprPortFilterMask | 1.3.6.1.4.1.495.2.1.6.36.1.1.13 | INTEGER | read-only | Indicates which bits of the 8-bit HDLC address are being used for address filtering on this port (CX900 or USIO only). Note: When a bit is set to '1', the position of bits will be checked. When a bit is set to '0', it will not be checked. Ranges of Values: 0 - 255 Default Value: 0 |
| INT bopSapOprPortFilterAddress1 | 1.3.6.1.4.1.495.2.1.6.36.1.1.14 | INTEGER | read-only | Indicates one of four 8-bit addresses used for address filtering (CX900 or USIO only). Ranges of Values: 0 - 255 Default Value: 126 |
| INT bopSapOprPortFilterAddress2 | 1.3.6.1.4.1.495.2.1.6.36.1.1.15 | INTEGER | read-only | Indicates one of four 8-bit addresses used for address filtering (CX900 or USIO only). Ranges of Values: 0 - 255 Default Value: 126 |
| INT bopSapOprPortFilterAddress3 | 1.3.6.1.4.1.495.2.1.6.36.1.1.16 | INTEGER | read-only | Indicates one of four 8-bit addresses used for address filtering (CX900 or USIO only). Ranges of Values: 0 - 255 Default Value: 126 |
| INT bopSapOprPortFilterAddress4 | 1.3.6.1.4.1.495.2.1.6.36.1.1.17 | INTEGER | read-only | Indicates one of four 8-bit addresses used for address filtering (CX900 or USIO only). Ranges of Values: 0 - 255 Default Value: 126 |
| INT bopSapOprPortCrc | 1.3.6.1.4.1.495.2.1.6.36.1.1.18 | INTEGER | read-only | Determines which algorithm is being used for error detection. Options: crc-ccitt (1): CRC-ITU-T (uses X15+X12+X5+1 polynomial; ITU-T formerly CCITT) (locked for ISDN 'D' channel; can be selected for ISDN 'B' channel) crc-32 (2): CRC-32 (for Ethernet; uses X32+X26+X23+X22+X16+X12+X11+ X10+X8+X7+X5+X4+X2+X+1) (can be selected for ISDN 'B' channel) Default Value: crc-ccitt (1) |
| INT bopSapOprPortDtrUpTimer | 1.3.6.1.4.1.495.2.1.6.36.1.1.19 | INTEGER | read-only | Determines the time in seconds that the port must wait for DCD (DTR if DCE) after raising DTR (DCD if DCE) to determine if a connection can be established. This object has no meaning in ISDN connections. Note: This value will be set to zero if the port does not support an application requiring it. Ranges of Values: 0 - 65535 Default Value: 0 |
| INT bopSapOprPortTxWindow | 1.3.6.1.4.1.495.2.1.6.36.1.1.20 | INTEGER | read-only | Determines the active maximum number of buffers that may be queued onto the port driver (for transmission) by the associated upper layer. For ISDN ports, the value is locked at 8. Ranges of Values: 1 - 255 Default Value: 255 |
| INT bopSapOprPortDialMode | 1.3.6.1.4.1.495.2.1.6.36.1.1.21 | INTEGER | read-only | Identifies the operation mode when setting up connections. Options: n/a (0): object is not applicable dial-in-only (1): Only accept incoming calls; Will not make any outgoing calls. dial-out-only (2): Only make outgoing calls; Will not accept any incoming calls. dial-in-out (3): Accept incoming calls and make outgoing calls. Ranges of Values: 1 - 3 Default Value: dial-in-out |
| INT bopSapOprPortLoopback | 1.3.6.1.4.1.495.2.1.6.36.1.1.28 | INTEGER | read-only | Determines whether loopback is enabled and what kind of loopback is enabled. Options: n/a (0): object is not applicable none (1): Loopback is not enabled local (2): Local loopback is enabled (return outbound frames to the originating software layer without transmitting them) remote (3): Remote loopback is enabled (forces the port to return (transmit) any frame received on the line, and causes the port to deny communication with any upper layer that requests service) both (4):Both local and remote loopbacks are enabled. isdn-uif-uif (5): ISDN loopback is enabled at U-Interface (forces TB1Q signal from a remote transmitter to pass through the entire U-Interface Transceiver before being transmitted back to the remote receiver) isdn-uif-idl2 (6): ISDN loopback is enabled at IDL2 Controller (forces IDL2 Controller to take in B and D channel data on IDL RX pin and send it out on IDL2 TX pin) isdn-uif-framer (7): ISDN loopback is enabled at framer (forces B and D channel data in on D-in pin and M channel data in on SCP which together undergo framing and deframing functions before B and D channel data go out D-out pin and M channel data go out SCP) isdn-uif-external (8): ISDN loopback is enabled at external line (forces TB1Q signal coming in on D-in pin to pass through Tx Driver pins, the U-Interface circuit and Rx input pins before recovering it and sending it out the D-out pin) Default Value: none |
| INT bopSapOprPortSignalSamplingPeriod | 1.3.6.1.4.1.495.2.1.6.36.1.1.29 | INTEGER | read-write | Determines the active sampling period in 100 millisecond increments that this port uses to sample signals. This object has no meaning in ISDN connections. Ranges of Values: 3 - 100 Default Value: 5 Configuration Changed: operative |
| INT bopSapOprPortDcdDtrSignalSamples | 1.3.6.1.4.1.495.2.1.6.36.1.1.30 | INTEGER | read-write | Determines the active number of sampling periods that this port must wait before validating DCD (DTR if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1 - 30 Default Value: 3 Configuration Changed: operative |
| INT bopSapOprPortCtsRtsSignalSamples | 1.3.6.1.4.1.495.2.1.6.36.1.1.31 | INTEGER | read-write | Determines the active number of sampling periods that this port must wait before validating CTS (RTS if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1-30 Default Value: 3 Configuration Changed: operative |
| INT bopSapOprPortDsrDrsSignalSamples | 1.3.6.1.4.1.495.2.1.6.36.1.1.32 | INTEGER | read-write | Determines the active number of sampling periods that this port must wait before validating DRS (DSR if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1 - 30 Default Value: 3 Configuration Changed: operative |
| INT bopSapOprPortTmLlSignalSamples | 1.3.6.1.4.1.495.2.1.6.36.1.1.33 | INTEGER | read-write | Determines the active number of sampling periods that this port must wait before validating TM (LL if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1 - 30 Default Value: 3 Configuration Changed: operative |
| INT bopSapOprPortRiRlSignalSamples | 1.3.6.1.4.1.495.2.1.6.36.1.1.34 | INTEGER | read-write | Determines the active number of sampling periods that this port must wait before validating RI (RL if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1 - 30 Default Value: 3 Configuration Changed: operative |
| INT bopSapOprPortStatisticsTimer | 1.3.6.1.4.1.495.2.1.6.36.1.1.35 | INTEGER | read-only | Determines the active period in seconds during which BOP performance statistics are measured. Note: If set to zero, BOP performance statistics are not measured. Ranges of Values: 0 - 60 Default Value: 0 |
| INT bopSapOprPortCarrierAction | 1.3.6.1.4.1.495.2.1.6.36.1.1.36 | INTEGER | read-write | Determines if the port driver informs it's associated upper layer that service is no longer available following loss of DCD if DTE, or DTR if DCE. Options: disabled (1): do not notify upper layer (locked for ISDN and T1/E1 ports) enabled (2): notify upper layer Default Value: enabled (2) Configuration Changed: operative |
| INT bopSapOprPortDataGenerator | 1.3.6.1.4.1.495.2.1.6.36.1.1.37 | INTEGER | read-write | Determines whether this port acts as an internal data generator. Options: n/a (0): object is not applicable disabled (1): port is not a data generator enabled (2): port is a data generator enabled-verify (3): port is a data generator and its incoming data is verified retrigger (4): port restarts data generation with defined parameters Default Value: disabled (1) Configuration Changed: operative |
| INT bopSapOprPortGenFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.38 | INTEGER | read-write | Determines the number of frames that the port configured as an internal data generator will generate at one time. Ranges of Values: 0 - 255 Note: When set to zero, frames are generated continuously Default Value: 1 Configuration Changed: operative |
| INT bopSapOprPortGenFrameSize | 1.3.6.1.4.1.495.2.1.6.36.1.1.39 | INTEGER | read-write | Determines the size in bytes of internally generated frames (excluding flags). Ranges of Values: 2 - 65,535 Note: When set to zero, frames are sized randomly. Default Value: 128 Configuration Changed: operative |
| INT bopSapOprPortGenFrameHeader | 1.3.6.1.4.1.495.2.1.6.36.1.1.40 | INTEGER | read-write | Determines the 16-bit header that is inserted in the first two octets after the opening flag of each internally generated frame. Ranges of Values: 0 - 65,535 Default Value: 1 Configuration Changed: operative |
| INT bopSapOprPortThreshBandwidth | 1.3.6.1.4.1.495.2.1.6.36.1.1.41 | INTEGER | read-only | Determines the value of the minimum critical bandwidth that determines whether Frame Relay should filter certain restricted types of packets or not. The value entered should be a multiple of 1 Kilo bits per second. Ranges of Values: 0 - 65,535 Default Value: 0 Configuration Changed: operative |
| INT bopSapOprPortActualSpeed | 1.3.6.1.4.1.495.2.1.6.36.1.1.42 | INTEGER | read-only | Determines the actual calculated output speed in bits per second of the port. Ranges of Values: 375 - 2,048,000 Default Value: 0 |
| INT bopSapOprCodeSet | 1.3.6.1.4.1.495.2.1.6.36.1.1.43 | INTEGER | read-only | Indicates the code used to communicate with the Bisync device. Options: (0) N/A: object is not applicable (1) EBCDIC code set (2) ASCII code set Default value: ebcdic |
| INT bopSapOprParity | 1.3.6.1.4.1.495.2.1.6.36.1.1.44 | INTEGER | read-only | Indicates the parity used to communicate with the Bisync device Options: (0) N/A: Object is not applicable (1) none: No parity (2) odd: Odd parity (3) even: Even parity (4) space: Low parity (always 0's) (5) mark: High parity (always 1's) Default value: none |
| INT bopOprPortTrap | 1.3.6.1.4.1.495.2.1.6.36.1.1.47 | INTEGER | read-write | Determines whether this port produces a 'bopPortStatusChange' trap which can be retrieved by SNMP network management. Options: disabled (1): do not produce port status trap enabled (2): produce port status trap Default Value: disabled (1) Configuration Changed: operative |
| INT bopOprTxClockTrap | 1.3.6.1.4.1.495.2.1.6.36.1.1.48 | INTEGER | read-write | Determines whether this port produces a 'bopTxClockStatusChange' trap which can be retrieved by SNMP network management. Options: disabled (1): do not produce transmit clock status trap enabled (2): produce transmit clock status trap Default Value: disabled (1) Configuration Changed: operative |
| INT bopOprControlLine | 1.3.6.1.4.1.495.2.1.6.36.1.1.52 | INTEGER | write-only | Controls the state of the port. Options: forceDown (1): forces the port into a 'down' state forceUp (2): forces the port into an 'up' state forceReset (3): forces a reset of the port Default Value: none |
| INT bopOprControlStats | 1.3.6.1.4.1.495.2.1.6.36.1.1.53 | INTEGER | write-only | Specifies that port statistics are to be cleared. Options: clearSapStats (1): clears port statistics Default Value: none |
| INT bopStatOprPortType | 1.3.6.1.4.1.495.2.1.6.36.1.1.55 | INTEGER | read-only | Indicates the type of hardware strapping for the port. Options: unknown (1): unknown strapping dte (2): DTE strapping dce (3): DCE strapping Default Value: none |
| INT bopStatOprPortInterfaceType | 1.3.6.1.4.1.495.2.1.6.36.1.1.56 | INTEGER | read-only | Indicates the type of hardware interface of the port. Options: unknown (1) rs232d (2): V.24 v35 (3): V.35 x21(4): X.21 v34 (5): V.34 modem dds (6): 56K DSU/CSU uif (7): ISDN U-interface v36 (8): V.36 Default Value: none |
| INT bopStatOprPortState | 1.3.6.1.4.1.495.2.1.6.36.1.1.57 | INTEGER | read-only | Indicates the state of availability of the port. Options: portUp (1): port is up portDown (2): port is down portShutDown (3): port has been shut down portDownBadConfiguration (4): port is down due to bad configuration portOutOfOrder (5): port is out of order Default Value: none |
| INT bopStatOprTxClockState | 1.3.6.1.4.1.495.2.1.6.36.1.1.61 | INTEGER | read-only | Indicates the state availability of the transmit clock. Options: txClockDown (1): transmit clock is down txClockUp (2): transmit clock is up Default Value: none |
| INT bopStatOprDCDState | 1.3.6.1.4.1.495.2.1.6.36.1.1.62 | INTEGER | read-only | Indicates the state of the DCD signal. Options: unknown (1): DCD signal is in unknown state because hardware is not present inactive(2): DCD signal is low active (3): DCD signal is high Default Value: none |
| INT bopStatOprDTRState | 1.3.6.1.4.1.495.2.1.6.36.1.1.63 | INTEGER | read-only | Indicates the state of the DTR signal. Options: unknown (1): DTR signal is in unknown state because hardware is not present inactive (2): DTR signal is low active (3): DTR signal is high Default Value: none |
| INT bopStatOprRTSState | 1.3.6.1.4.1.495.2.1.6.36.1.1.64 | INTEGER | read-only | Indicates the state of the RTS signal. Options: unknown (1): RTS signal is in unknown state because hardware is not present inactive (2): RTS signal is low active (3): RTS signal is high Default Value: none |
| INT bopStatOprCTSState | 1.3.6.1.4.1.495.2.1.6.36.1.1.65 | INTEGER | read-only | Indicates the state of the CTS signal. Options: unknown (1): CTS signal is in unknown state because hardware is not present inactive (2): CTS signal is low active (3): CTS signal is high Default Value: none |
| INT bopStatOprDSRState | 1.3.6.1.4.1.495.2.1.6.36.1.1.66 | INTEGER | read-only | Indicates the state of the DSR signal. Options: unknown (1): DSR signal is in unknown state because hardware is not present inactive (2): DSR signal is low active =(3): SR signal is high Default Value: none |
| INT bopStatOprDRSState | 1.3.6.1.4.1.495.2.1.6.36.1.1.67 | INTEGER | read-only | Indicates the state of the DRS signal. Options: unknown (1): DRS signal is in unknown state because hardware is not present inactive (2): DRS signal is low active = DRS signal is high Default Value: none |
| INT bopStatOprTMState | 1.3.6.1.4.1.495.2.1.6.36.1.1.68 | INTEGER | read-only | Indicates the state of the TM signal. Options: unknown (1): TM signal is in unknown state because hardware is not present inactive (2): TM signal is low active (3): TM signal is high Default Value: none |
| INT bopStatOprLLState | 1.3.6.1.4.1.495.2.1.6.36.1.1.69 | INTEGER | read-only | Indicates the state of the LL signal. Options: unknown (1): LL signal is in unknown state because hardware is not present inactive (2): LL signal is low active (3): LL signal is high Default Value: none |
| INT bopStatOprRIState | 1.3.6.1.4.1.495.2.1.6.36.1.1.70 | INTEGER | read-only | Indicates the state of the RI signal. Options: unknown (1): RI signal is in unknown state because hardware is not present inactive (2): RI signal is low active (3): RI signal is high Default Value: none |
| INT bopStatOprRLState | 1.3.6.1.4.1.495.2.1.6.36.1.1.71 | INTEGER | read-only | Indicates the state of the RL signal. Options: unknown (1): RL signal is in unknown state because hardware is not present inactive (2): RL signal is low active (3): RL signal is high Default Value: none |
| CTR bopStatOprTxFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.75 | Counter | read-only | Indicates the total number of Tx frames since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprRxFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.76 | Counter | read-only | Indicates the total number of Rx frames since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprLocalLoopbackFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.77 | Counter | read-only | Indicates the total number of frames locally looped back since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprTxBps | 1.3.6.1.4.1.495.2.1.6.36.1.1.78 | Counter | read-only | Indicates the number of transmitted bits divided by the number of seconds set in 'bopSapOprPortStatisticsTimer'. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprRxBps | 1.3.6.1.4.1.495.2.1.6.36.1.1.79 | Counter | read-only | Indicates the number of received bits divided by the number of seconds set in 'bopSapOprPortStatisticsTimer'. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprTxBpsMax | 1.3.6.1.4.1.495.2.1.6.36.1.1.80 | Counter | read-only | Indicates the highest number of bits per second transmitted since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprRxBpsMax | 1.3.6.1.4.1.495.2.1.6.36.1.1.81 | Counter | read-only | Indicates the highest number of bits per second received since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprTxFps | 1.3.6.1.4.1.495.2.1.6.36.1.1.82 | Counter | read-only | Indicates the number of transmitted frames divided by the number of seconds set in 'bopSapOprPortStatisticsTimer'. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprRxFps | 1.3.6.1.4.1.495.2.1.6.36.1.1.83 | Counter | read-only | Indicates the number of received frames divided by the number of seconds set in 'bopSapOprPortStatisticsTimer'. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprTxFpsMax | 1.3.6.1.4.1.495.2.1.6.36.1.1.84 | Counter | read-only | Indicates the highest number of frames per second transmitted since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprRxFpsMax | 1.3.6.1.4.1.495.2.1.6.36.1.1.85 | Counter | read-only | Indicates the highest number of frames per second received since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprTxUnderrunFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.86 | Counter | read-only | Indicates the total number of underrun frames that have been unsuccessfully transmitted since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
| CTR bopStatOprTxCtsLostFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.87 | Counter | read-only | Indicates the total number of frames unsuccessfully transmitted in half-duplex because CTS was dropped during transmission. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprTxBadStateDiscards | 1.3.6.1.4.1.495.2.1.6.36.1.1.88 | Counter | read-only | Indicates the total number of frames discarded since statistics were last reset, due to a request for frame transmission while the port was down ('bopStatOprPortState' = portDown, portShutDown, portDownBadConfiguration, or portOutOfOrder). Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprTxResetDiscards | 1.3.6.1.4.1.495.2.1.6.36.1.1.89 | Counter | read-only | Indicates the total number of frames discarded since statistics were last reset, due to a management request for a line reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprTxSysCongestionDiscards | 1.3.6.1.4.1.495.2.1.6.36.1.1.90 | Counter | read-only | Indicates the total number of frames discarded since statistics were last reset, due to system congestion. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprTxInvWinDiscards | 1.3.6.1.4.1.495.2.1.6.36.1.1.91 | Counter | read-only | Indicates the total number of frames discarded since statistics were last reset, due to the transmit window being exceeded. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprTxInvRLpbkWinDiscards | 1.3.6.1.4.1.495.2.1.6.36.1.1.92 | Counter | read-only | Indicates the total number of frames discarded since statistics were last reset, due to the transmit window being exceeded while in loopback mode. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprRxBadCrcFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.98 | Counter | read-only | Indicates the total number of bad CRC frames received since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprRxAbortedFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.99 | Counter | read-only | Indicates the total number of aborted frames received since statistics were last reset. Note: A frame is aborted when the port's receiver detects seven consecutive ones in that frame. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprRxNonIntegralBitFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.100 | Counter | read-only | Indicates the total number of frames received since statistics were last reset, that did not have eight bits per byte. Note: Non-integral bit frames cannot be divided evenly by eight (the number of bits per byte in a frame). Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprRxLongFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.101 | Counter | read-only | Indicates the total number of long frames received since statistics were last reset. Note: A long frame is counted each time a received frame exceeds the permitted frame length defined in 'bopSapOprPortMaxFrameSize'. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprRxOverrunFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.102 | Counter | read-only | Indicates the total number of overrun frames received since statistics were last reset. Note: An overrun indicates that a frame's contents have been corrupted due to slow response in data reception. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprRxCdLostFrames | 1.3.6.1.4.1.495.2.1.6.36.1.1.103 | Counter | read-only | Indicates the total number of frames received with DCD loss in half-duplex by the port. Ranges of Values: 0 - 65, 535 Default Value: none |
| CTR bopStatOprRxBadStateDiscards | 1.3.6.1.4.1.495.2.1.6.36.1.1.104 | Counter | read-only | Indicates the total number of frames discarded since statistics were last reset, because BOP software layer was not bound to other layers. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprRxBusyDiscards | 1.3.6.1.4.1.495.2.1.6.36.1.1.105 | Counter | read-only | Indicates the total number of frames discarded since statistics were last reset, due to a lack of receive buffers. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprPortStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.109 | Counter | read-only | Indicates the total number of times the port has moved from one state to another since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprTxClockStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.110 | Counter | read-only | Indicates the total number of times that 'bopStatOprTxClockState' has moved from one state to another since were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprDCDStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.111 | Counter | read-only | Indicates the total number of times DCD has moved from one state to another since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprDTRStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.112 | Counter | read-only | Indicates the total number of times DTR has moved from one state to another since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprRTSStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.113 | Counter | read-only | Indicates the total number of times RTS has moved from one state to another since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprCTSStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.114 | Counter | read-only | Indicates the total number of times CTS has moved from one state to another since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprDSRStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.115 | Counter | read-only | Indicates the total number of times DSR has moved from one state to another since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprDRSStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.116 | Counter | read-only | Indicates the total number of times DRS has moved from one state to another since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprTMStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.117 | Counter | read-only | Indicates the total number of times TM has moved from one state to another since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprLLStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.118 | Counter | read-only | Indicates the total number of times LL has moved from one state to another since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprRIStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.119 | Counter | read-only | Indicates the total number of times RI has moved from one state to another since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprRLStateChanges | 1.3.6.1.4.1.495.2.1.6.36.1.1.120 | Counter | read-only | Indicates the total number of times RL has moved from one state to another since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprPortResets | 1.3.6.1.4.1.495.2.1.6.36.1.1.121 | Counter | read-only | Indicates the total number of port resets that have occurred at the port since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value: none |
| CTR bopStatOprRxGenError | 1.3.6.1.4.1.495.2.1.6.36.1.1.123 | Counter | read-only | Indicates the total number of frames received in error since statistics were last reset, while 'bopSapOprPortDataGenerator' was set to 'enabled-verify'. Ranges of Values: 0 - 65,535 Default Value: none |
| bopSapAdmTable | 1.3.6.1.4.1.495.2.1.6.36.2 | not-accessible | A table containing the planned configuration information about each BOP/COP port. | |
| bopSapAdmEntry | 1.3.6.1.4.1.495.2.1.6.36.2.1 | not-accessible | The planned configuration information for a specific BOP/COP port. | |
| INT bopSapAdmNumber | 1.3.6.1.4.1.495.2.1.6.36.2.1.1 | INTEGER | read-only | Defines the SAP ID using 2,3 or 4 digits. The first digit (A) is the slot #, the second digit (B) is the port #, and the remaining digits (CD) are the channel #. If a 2 digit number is entered, digits CD are assumed to be 0 and are inserted automatically when reading object. If a 3 digit number is entered, digit C is assumed to be 0 and is inserted automatically when reading object. Ranges of Values for A: 1-7 for CX900, 1-4 for CX1000 Ranges of Values for B: 1-5 for CX900, 1-4 for CX1000 Ranges of Values for CD: 00-30 Default Value: not applicable |
| ALI bopSapAdmAlias | 1.3.6.1.4.1.495.2.1.6.36.2.1.2 | Alias | read-write | Determines the textual name uniquely identifying this SAP in the BOP Driver software layer. Ranges of Values: 0-16 alphanumeric characters beginning with a non-numeric character Default Value: undefined Configuration Changed: administrative |
| INT bopSapAdmProtocol | 1.3.6.1.4.1.495.2.1.6.36.2.1.3 | INTEGER | read-write | Determines if the port is HDLC or Bisync. Only HDLC is supported by ISDN and T1/E1 ports. Indicates in the operative configuration the type of bisync protocol used by the controllers of the port associated with this SAP. Options: hdlc bsc3270 = Bisync 3270 controllers borroughs = Borroughs controllers sperry = Sperry controllers bsc3780 = Bisync 2780/3780 controllers aircat = aircat500 air traffic radar controllers Default Value: hdlc |
| INT bopSapAdmPortClockSource | 1.3.6.1.4.1.495.2.1.6.36.2.1.5 | INTEGER | read-write | Determines the bit-rate clock source of the port. Options: internal (1): Tx and Rx clocks are internally generated external (2): Tx and Rx clocks are externally supplied on separate pins split (3): Tx clock is internally generated and Rx clock is externally supplied slave (4): Tx and Rx clocks are externally supplied on the same pins Note: Split clocking is not supported on ports in slots 5, 6 and 7 when the Data Expansion Module is installed. Default Value: external (locked to internal for ISDN) Configuration Changed: administrative |
| INT bopSapAdmPortSpeed | 1.3.6.1.4.1.495.2.1.6.36.2.1.6 | INTEGER | read-write | Indicates the input and output speed in bits per second of the port. Note: This value is meaningful only if 'bopSapAdmPortClockSource' is set to 'internal' or to 'split'. Ranges of Values: 375 - 2,048,000 (locked at 16,000 for ISDN 'D' channel and at 64,000 for ISDN 'B' channels) for slot/port/channel 11x-41x; 300-256,000 for slot/port/channel 51x-71x. 1875 bps is the minimum speed supported on ports in slots 5, 6 and 7 when the Data Expansion Module is installed. Default Value: 64,000 Configuration Changed: administrative |
| INT bopSapAdmPortDuplex | 1.3.6.1.4.1.495.2.1.6.36.2.1.7 | INTEGER | read-write | Determines whether the port communicates simultaneously in both directions (full-duplex) or alternates between directions (half-duplex). Options: half (1): half-duplex full (2): full-duplex (locked for ISDN) Default Value: full Configuration Changed: administrative |
| INT bopSapAdmPortMaxFrameSize | 1.3.6.1.4.1.495.2.1.6.36.2.1.8 | INTEGER | read-write | Determines the maximum frame size supported by the port. Ranges of Values: 32-9000 Default Value: 1,600 (512 for ISDN) Configuration Changed: administrative |
| INT bopSapAdmPortDataEncoding | 1.3.6.1.4.1.495.2.1.6.36.2.1.9 | INTEGER | read-write | Determines the data formatting and encoding used by the port. Options: nrz (1): NRZ (locked for ISDN 'D' channel; ISDN 'B' channel can use only this value or NRZI-Space value) nrzi-mark (2): NRZI-Mark nrzi-space (3): NRZI-Space (ISDN 'B' channel can use only this value or NRZ value) Note: Slot/port/channel 51x-71x can use only NRZ or NRZI-Space. Default Value: nrz (1) Configuration Changed: administrative |
| INT bopSapAdmPortIdleCondition | 1.3.6.1.4.1.495.2.1.6.36.2.1.10 | INTEGER | read-write | Determines the idle line condition supported by the port. Options: flags (1): flags marks (2): marks as400 (3): AS400 Default Value: flags Configuration Changed: administrative |
| INT bopSapAdmPortPreAmbleLength | 1.3.6.1.4.1.495.2.1.6.36.2.1.11 | INTEGER | read-write | Determines the minimum number of flags or sync pairs that will be inserted between frames by the port's transmitter. For HDLC frames: A value of zero causes flag sharing between frames. A value of one means no flag sharing and zero flags inserted between frames. A value of two means no flag sharing and one flag inserted between frames. A value of three means no flag sharing and two flags inserted between frames. Etc. For Bisync frames: A value of zero or one causes one sync pair to be inserted between frames. A value of two causes two sync pairs to be inserted between frames. A value of three causes three sync pairs to be inserted between frames. Etc. Ranges of Values: 0-16 Default Value: 1 Configuration Changed: administrative |
| INT bopSapAdmPortFlagSharing | 1.3.6.1.4.1.495.2.1.6.36.2.1.12 | INTEGER | read-write | Determines whether back-to-back transmit frames will have a flag in common This value is meaningful only if 'bopSapAdmPortPreAmbleLength' is set to zero. Options: disabled (1): back-to-back frames do not share flag enabled (2): back-to-back frames share flag Default Value: disabled Configuration Changed: administrative |
| INT bopSapAdmPortFilterMask | 1.3.6.1.4.1.495.2.1.6.36.2.1.13 | INTEGER | read-write | Determines which bits of the 8-bit HDLC address will be used for address filtering. Note: When a bit is set to '1', the position of bits will be checked. When a bit is set to '0', it will not be checked. Ranges of Values: 0-255 Default Value: 0 Configuration Changed: administrative |
| INT bopSapAdmPortFilterAddress1 | 1.3.6.1.4.1.495.2.1.6.36.2.1.14 | INTEGER | read-write | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Changed: administrative |
| INT bopSapAdmPortFilterAddress2 | 1.3.6.1.4.1.495.2.1.6.36.2.1.15 | INTEGER | read-write | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Changed: administrative |
| INT bopSapAdmPortFilterAddress3 | 1.3.6.1.4.1.495.2.1.6.36.2.1.16 | INTEGER | read-write | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Changed: administrative |
| INT bopSapAdmPortFilterAddress4 | 1.3.6.1.4.1.495.2.1.6.36.2.1.17 | INTEGER | read-write | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Changed: administrative |
| INT bopSapAdmPortCrc | 1.3.6.1.4.1.495.2.1.6.36.2.1.18 | INTEGER | read-write | Determines which algorithm is used for error detection. Options: crc-ccitt (1): CRC-ITU-T (uses X15+X12+X5+1 polynomial; ITU-T formerly CCITT) (locked for ISDN 'D' channel; can be selected for ISDN 'B' channel) crc-32 (2): CRC-32 (for Ethernet; uses X32+X26+X23+X22+X16+X12+X11+ X10+X8+X7+X5+X4+X2+X+1) (can be selected for ISDN 'B' channel) Default Value: crc-ccitt (1) Configuration Changed: administrative |
| INT bopSapAdmPortDtrUpTimer | 1.3.6.1.4.1.495.2.1.6.36.2.1.19 | INTEGER | read-write | Determines the time in seconds that the port must wait for DCD (DTR if DCE) after raising DTR (DCD if DCE) to determine if a connection can be established. Note: This value will be set to zero if the port does not support an application requiring it. Ranges of Values: 0-65,535 Default Value: 0 Configuration Changed: administrative |
| INT bopSapAdmPortTxWindow | 1.3.6.1.4.1.495.2.1.6.36.2.1.20 | INTEGER | read-write | Determines the maximum number of buffers that may be queued onto the port driver (for transmission) by the associated upper layer. For ISDN ports, the value is locked at 8. Note: When set to '255', the system automatically determines the number of buffers devoted to different kinds of traffic. When this object is set to a lesser value, the system compares this value with its own and uses the smaller. This object thereby provides a way to safeguard delay-sensitive voice traffic against such disruptions as bursty LAN traffic. This value is locked to 255 for ISDN. Ranges of Values: 1-255 Default Value: 255 Configuration Changed: administrative |
| INT bopSapAdmPortThreshBandwidth | 1.3.6.1.4.1.495.2.1.6.36.2.1.21 | INTEGER | read-write | Determines the value of the minimum critical bandwidth that will determine whether Frame Relay should filter certain restricted types of packets or not. The value entered should be a multiple of 1 Kilo bits per second. Ranges of Values: 0 - 65,535 Default Value: 0 Configuration Changed: operative |
| INT bopSapAdmPortDialMode | 1.3.6.1.4.1.495.2.1.6.36.2.1.22 | INTEGER | read-write | Identifies the operation mode when setting up connections. Options: dial-in-only (1): Only accept incoming calls; Will not make any outgoing calls. dial-out-only (2): Only make outgoing calls; Will not accept any incoming calls. dial-in-out (3): Accept incoming calls and make outgoing calls. Configuration Changed: administrative |
| INT bopSapAdmPortLoopback | 1.3.6.1.4.1.495.2.1.6.36.2.1.28 | INTEGER | read-write | Determines whether loopback is enabled and what kind of loopback is enabled. Options: none (1): Loopback is not enabled local (2): Local loopback is enabled (forces SAP associated with port to return outbound frames to the originating software layer without transmitting them) remote (3): Remote loopback is enabled (forces the port to transmit immediately any frame received on the line, and also forces the associated SAP to deny communication with any upper software layer that requests service) both (4): Both local and remote loopbacks are enabled. isdn-uif-uif (5): ISDN loopback is enabled at U-Interface (forces TB1Q signal from a remote transmitter to pass through the entire U-Interface Transceiver before being transmitted back to the remote receiver) isdn-uif-idl2 (6): ISDN loopback is enabled at IDL2 Controller (forces IDL2 Controller to take in B and D channel data on IDL RX pin and send it out on IDL2 TX pin) isdn-uif-framer (7): ISDN loopback is enabled at framer (forces B and D channel data in on D-in pin and M channel data in on SCP which together undergo framing and deframing functions before B and D channel data go out D-out pin and M channel data go out SCP) isdn-uif-external (8): ISDN loopback is enabled at external line (forces TB1Q signal coming in on D-in pin to pass through Tx Driver pins, the U-Interface circuit and Rx input pins before recovering it and sending it out the D-out pin) Default Value: none Configuration Changed: administrative |
| INT bopSapAdmPortSignalSamplingPeriod | 1.3.6.1.4.1.495.2.1.6.36.2.1.29 | INTEGER | read-write | Determines the sampling period in 100 millisecond increments used to sample detectable signals. Ranges of Values: 3-100 (locked at 5 for ISDN) Default Value: 5 Configuration Changed: administrative |
| INT bopSapAdmPortDcdDtrSignalSamples | 1.3.6.1.4.1.495.2.1.6.36.2.1.30 | INTEGER | read-write | Determines the active number of sampling periods that this port must wait before validating DCD (DTR if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1-30 Default Value: 3 Configuration Changed: administrative |
| INT bopSapAdmPortCtsRtsSignalSamples | 1.3.6.1.4.1.495.2.1.6.36.2.1.31 | INTEGER | read-write | Determines the active number of sampling periods that this port must wait before validating CTS (RTS if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1-30 Default Value: 3 Configuration Changed: administrative |
| INT bopSapAdmPortDsrDrsSignalSamples | 1.3.6.1.4.1.495.2.1.6.36.2.1.32 | INTEGER | read-write | Determines the active number of sampling periods that this port must wait before validating DSR (DRS if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1-30 Default Value: 3 Configuration Changed: administrative |
| INT bopSapAdmPortTmLlSignalSamples | 1.3.6.1.4.1.495.2.1.6.36.2.1.33 | INTEGER | read-write | Determines the active number of sampling periods that this port must wait before validating TM (LL if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1-30 Default Value: 3 Configuration Changed: administrative |
| INT bopSapAdmPortRiRlSignalSamples | 1.3.6.1.4.1.495.2.1.6.36.2.1.34 | INTEGER | read-write | Determines the active number of sampling periods that this port must wait before validating RI (RL if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1-30 Default Value: 3 Configuration Changed: administrative |
| INT bopSapAdmPortStatisticsTimer | 1.3.6.1.4.1.495.2.1.6.36.2.1.35 | INTEGER | read-write | Determines the period in seconds during which BOP performance statistics are measured. Note: If set to zero, BOP performance statistics are not measured. Ranges of Values: 0-60 Default Value: 0 Configuration Changed: administrative |
| INT bopSapAdmPortCarrierAction | 1.3.6.1.4.1.495.2.1.6.36.2.1.36 | INTEGER | read-write | Determines if the port driver informs it's associated upper layer that service is no longer available following loss of DCD if DTE, or DTR if DCE. Options: disabled (1): do not notify upper layer of service loss (locked for ISDN) enabled (2): inform upper layer of service loss Default Value: enabled Configuration Changed: administrative |
| INT bopSapAdmPortDataGenerator | 1.3.6.1.4.1.495.2.1.6.36.2.1.37 | INTEGER | read-write | Determines whether the port will act as an internal data generator. Options: disabled (1): port is not a data generator enabled (2): port is a data generator enabled-verify (3): port is a data generator and its incoming data is verified Default Value: disabled Configuration Changed: administrative |
| INT bopSapAdmPortGenFrames | 1.3.6.1.4.1.495.2.1.6.36.2.1.38 | INTEGER | read-write | Determines the number of frames that the port configured as an internal data generator will generate at one time. Ranges of Values: 0-255 Note: When set to zero, frames are generated continuously Default Value: 1 Configuration Changed: administrative |
| INT bopSapAdmPortGenFrameSize | 1.3.6.1.4.1.495.2.1.6.36.2.1.39 | INTEGER | read-write | Determines the size in bytes of internally generated frames (excluding flags). Ranges of Values: 2-65535 Note: When set to zero, frames are sized randomly. Default Value: 128 Configuration Changed: administrative |
| INT bopSapAdmPortGenFrameHeader | 1.3.6.1.4.1.495.2.1.6.36.2.1.40 | INTEGER | read-write | Determines the 16-bit header that will be inserted in the first two octets after the opening flag of each internally generated frame. Ranges of Values: 0-65, 535 Default Value: 1 Configuration Changed: administrative |
| INT bopSapAdmCodeSet | 1.3.6.1.4.1.495.2.1.6.36.2.1.45 | INTEGER | read-write | Determines in the administrative configuration the code used by the port associated with this SAP to communicate to the Bisync device. Options: other ebcdic = EBCDIC ascii = ASCII Default value: ebcdic Configuration changed: administrative Further action: system reset to change |
| INT bopSapAdmParity | 1.3.6.1.4.1.495.2.1.6.36.2.1.46 | INTEGER | read-write | Indicates the parity used to communicate with the Bisync device Options: (1) none: No parity (2) odd: Odd parity (3) even: Even parity (4) space: Low parity (always 0's) (5) mark: High parity (always 1's) Default value: none |
| INT bopAdmPortTrap | 1.3.6.1.4.1.495.2.1.6.36.2.1.47 | INTEGER | read-write | Determines whether this port produces a 'bopPortStatusChange' trap which can be retrieved by SNMP network management. Options: disabled (1): do not produce port status trap enabled (2): produce port status trap Default Value: disabled (1) Configuration Changed: administrative |
| INT bopAdmTxClockTrap | 1.3.6.1.4.1.495.2.1.6.36.2.1.48 | INTEGER | read-write | Determines whether this port produces a 'bopTxClockStatusChange' trap which can be retrieved by SNMP network management. Options: disabled (1): do not produce transmit clock status trap enabled (2): produce transmit clock status trap Default Value: disabled (1) Configuration Changed: administrative |
| INT bopMibLevel | 1.3.6.1.4.1.495.2.1.6.36.3 | INTEGER | read-only | Used to determine current MIB module release supported by the agent. Object is in decimal. |
RFC description
Vendor-private MIB for CX series box I/O operations and device management.
Start monitoring Aastra CX WAN access equipment (BOP I/O module) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.