JNX-OPT-IF-EXT-MIB

All MIBs › JNX-OPT-IF-EXT-MIB

Organization: IETF Ops/Camp MIB Working Group

Last Updated: 2012-04-25

Category: Domain: Optical Transport, Network Interfaces, Optical and WDM, Technology: Optical Transport, Vendor: Juniper

Description: Defines extensions to the optical interface MIB for Juniper Networks, providing additional optics monitoring and configuration objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is JNX-OPT-IF-EXT-MIB?

JNX-OPT-IF-EXT-MIB is a Juniper Networks enterprise MIB extending optical interface management for DWDM/OTN transport equipment, built as an enterprise extension to the 'Black Link' concept from ITU-T G.698.2 and related optical-transport drafts. It exposes configuration and monitoring objects for optical parameters at both the optical multiplex-section (OPSm) and optical-channel (OCh) layers, including directionality, fiber-type recommendations, channel spacing, bit-rate line coding, forward error correction (FEC) settings, and bit-error-rate (BER) sink thresholds/mantissa-exponent values. As a monitoring tool it is used for optical hardware/signal-quality status: tracking configured FEC and BER threshold parameters alongside channel configuration to detect optical signal degradation, and it defines OTN notification objects for alerting on optical-transport faults. It explicitly builds on RFC 3591 (optical interface MIB) and the ITU-T/IETF Black Link and G.698.2 draft standards, showing clear dependency on those base optical-transport standards. It is deployed on Juniper Networks optical/DWDM transport platforms used in long-haul or metro optical networks requiring precise per-channel optical parameter monitoring, where JNX-OPT-IF-EXT-MIB SNMP monitoring tracks FEC and BER thresholds to catch optical signal degradation early.

IPNetwork Monitor allows you to monitor SNMP objects defined in JNX-OPT-IF-EXT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper Networks DWDM/optical transport platform

Monitoring Examples

An operator reviews jnxoptIfOChConfigExtTable/jnxoptIfOChConfigExtEntry to check jnxoptIfOChBitRateLineCoding and jnxoptIfOChFEC settings on an optical channel, then monitors jnxoptIfOChSinkMaximumBERMantissa and jnxoptIfOChSinkMaximumBERExponent to see if the received bit-error rate is approaching the configured maximum threshold, signaling optical signal degradation. The jnxoptIfOPSmConfigTable's jnxoptIfOPSmFiberTypeRecommendation and jnxoptIfOPSmDirectionality would be checked to confirm the multiplex-section fiber type and direction match the physical fiber plant, and jnxoptIfOTNNotifications would deliver a trap if an OTN-layer fault occurs.

What Can Be Monitored

optical channel FEC configuration
bit-error-rate threshold vs. actual
channel spacing/bit-rate coding
fiber type/directionality configuration
OTN fault notifications

Imported Objects

From IF-MIB

ifIndex

OBJECT-TYPE

From JNX-OPT-IF-MIB

JnxoptIfDirectionality
jnxoptIfMibModule	MODULE-IDENTITY
jnxoptIfOChConfigEntry	OBJECT-TYPE
jnxoptIfOChSinkCurrentEntry	OBJECT-TYPE

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32
transmission

From SNMPv2-TC

DateAndTime
DisplayString
RowPointer
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using jnxoptIfOTNPMCurrentFECCorrectedErr OID:

Select a Juniper Networks DWDM/optical transport platform (Black Link/G.698.2 extension) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type jnxoptIfOTNPMCurrentFECCorrectedErr into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of bits corrected by the FEC are counted in the interval. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
jnxoptIfExtMibModule	1.3.6.1.4.1.2636.3.73.1.3			The MIB module to describe Black Link extension to rfc3591. It is the enterprise version of the draft draft-galikunze-ccamp-g-698-2-snmp-mib-02
jnxoptIfOTNNotifications	1.3.6.1.4.1.2636.3.73.1.3.0
NTF jnxoptIfOTNOChOTUkAlarmSet	1.3.6.1.4.1.2636.3.73.1.3.0.1			Notification of a recently set OTN alarm of Layer and Type.
NTF jnxoptIfOTNOChOTUkAlarmClear	1.3.6.1.4.1.2636.3.73.1.3.0.2			Notification of a recently clear OTN alarm of Layer and Type.
NTF jnxoptIfOTNODUkTcmAlarmSet	1.3.6.1.4.1.2636.3.73.1.3.0.3			Notification of a recently set OTN alarm of Layer and Type.
NTF jnxoptIfOTNODUkTcmAlarmClear	1.3.6.1.4.1.2636.3.73.1.3.0.4			Notification of a recently clear OTN alarm of Layer and Type.
jnxoptIfOPSmEntry	1.3.6.1.4.1.2636.3.73.1.3.1
jnxoptIfOPSmConfigTable	1.3.6.1.4.1.2636.3.73.1.3.1.1		not-accessible	A table of OPS General config parameters.
jnxoptIfOPSmConfigEntry	1.3.6.1.4.1.2636.3.73.1.3.1.1.1		not-accessible	An conceptual row of OPS General config parameters.
JNX jnxoptIfOPSmDirectionality	1.3.6.1.4.1.2636.3.73.1.3.1.1.1.1	JnxoptIfDirectionality	read-only	Indicates the directionality of the entity.
JNX jnxoptIfOPSmFiberTypeRecommendation	1.3.6.1.4.1.2636.3.73.1.3.1.1.1.2	JnxoptIfFiberTypeRecommendation	read-only	Fiber type as per fibre types are chosen from those defined in ITU-T Recs G.652, G.653, G.654, G.655, G.656 and G.657.
JNX jnxoptIfOPSmFiberTypeCategory	1.3.6.1.4.1.2636.3.73.1.3.1.1.1.3	JnxoptIfFiberTypeCategory	read-only	Fiber type as per fibre types are chosen from those defined in ITU-T Recs G.652, G.653, and G.655. The categories are A, B, C, D and E.
jnxoptIfOChSrcSinkGroup	1.3.6.1.4.1.2636.3.73.1.3.2
jnxoptIfOChConfigExtTable	1.3.6.1.4.1.2636.3.73.1.3.2.1		not-accessible	A table of Och General config extension parameters
jnxoptIfOChConfigExtEntry	1.3.6.1.4.1.2636.3.73.1.3.2.1.1		not-accessible	A conceptual row that contains OCh configuration extension information of an interface.
JNX jnxoptIfOChMiminumChannelSpacing	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.1	JnxoptIfChannelSpacing	read-only	A minimum nominal difference in frequency (GHz) between two adjacent channels.
JNX jnxoptIfOChBitRateLineCoding	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.2	JnxoptIfBitRateLineCoding	read-only	Optical tributary signal class NRZ 2.5G (from nominally 622 Mbit/s to nominally 2.67 Gbit/s) NRZ 10G (nominally 2.4 Gbit/s to nominally 10.71 Gbit/s)
U32 jnxoptIfOChFEC	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.3	Unsigned32	read-write	This parameter indicates what Forward Error Correction (FEC) code is used at Source and Sink. GFEC (from G709) and the I.x EFEC's (G.975 - Table I.1 super FEC). 1 - No FEC 2 - GFEC 3 - I.2 EFEC 4 - I.3 EFEC 5 - I.4 EFEC 6 - I.5 EFEC 7 - I.6 EFEC 8 - I.7 EFEC 9 - I.8 EFEC 10 - I.9 EFEC 11 - 100G FEC (for new applications) 12 - 100G EFEC (for new applications) 99 - Vendor Specific
U32 jnxoptIfOChSinkMaximumBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.4	Unsigned32	read-only	This parameter indicate the maximum Bit(mantissa) error rate can be supported by the application at the Receiver. In case of FEC applications it is intended after the FEC correction.
U32 jnxoptIfOChSinkMaximumBERExponent	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.5	Unsigned32	read-only	This parameter indicate the maximum Bit(exponent) error rate can be supported by the application at the Receiver. In case of FEC applications it is intended after the FEC correction.
U32 jnxoptIfOChMinWavelength	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.6	Unsigned32	read-only	This parameter indicate minimum wavelength spectrum in a definite wavelength Band (L, C and S)
U32 jnxoptIfOChMaxWavelength	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.7	Unsigned32	read-only	This parameter indicate maximum wavelength spectrum in a definite wavelength Band (L, C and S)
U32 jnxoptIfOChWavelength	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.8	Unsigned32	read-write	This parameter indicates the wavelength value.
STR jnxoptIfOChVendorTransceiverClass	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.9	DisplayString	read-only	As defined in G.698 Vendors can summarize a set of parameters in a single proprietary parameter: the Class of transceiver. The Transceiver classification will be based on the Vendor Name and the main TX and RX parameters (i.e. Trunk Mode, Framing, Bit rate, Trunk Type etc). If this parameter is used, the MIB parameters specifying the Transceiver characteristics may not be significant and the vendor will be responsible to specify the Class contents and values. The Vendor can publish the parameters of its Classes or declare to be compatible with published Classes.(G) Optional for compliance. (not mentioned in G.698)
STR jnxoptIfOChOpticalInterfaceApplicationCode	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.10	DisplayString	read-only	This parameter indicates the transceiver application code at Ss and Rs as defined in [ITU.G698.2] Chapter 5.3
INT jnxoptIfOChLaserAdminState	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.11	INTEGER	read-write	The configured State of the laser: 0 - disabled 1 - enabled
INT jnxoptIfOChLaserOperationalState	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.12	INTEGER	read-only	The Operational Status of Laser: 0 - disabled 1 - Enabled 2 - fault 3 - degraded
INT jnxoptIfOChAdminState	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.13	INTEGER	read-write	The Administrative Status of an Interface: 0 - Out of Service 1 - In Service
INT jnxoptIfOChOperationalState	1.3.6.1.4.1.2636.3.73.1.3.2.1.1.14	INTEGER	read-only	The Operational Status of an Interface: 0 - disabled 1 - enabled 2 - Fault 3 - Degraded
jnxoptIfOChSrcConfigTable	1.3.6.1.4.1.2636.3.73.1.3.2.2		not-accessible	A configuration table of OCh Src (Ss) parameters.
jnxoptIfOChSrcConfigEntry	1.3.6.1.4.1.2636.3.73.1.3.2.2.1		not-accessible	A conceptual row that contains the Src (Ss) configuration parameters for a given interface.
I32 jnxoptIfOChMinimumMeanChannelOutputPower	1.3.6.1.4.1.2636.3.73.1.3.2.2.1.1	Integer32	read-only	The minimum mean launched power at Ss is the average power (in dbm) of a pseudo-random data sequence coupled into the DWDM link.
I32 jnxoptIfOChMaximumMeanChannelOutputPower	1.3.6.1.4.1.2636.3.73.1.3.2.2.1.2	Integer32	read-only	The maximum mean launched power at Ss is the average power (in dbm) of a pseudo-random data sequence coupled into the DWDM link.
U32 jnxoptIfOChMinimumCentralFrequency	1.3.6.1.4.1.2636.3.73.1.3.2.2.1.3	Unsigned32	read-only	The minimum central frequency is the nominal single-channel frequency (in THz) on which the digital coded information of the particular optical channel is modulated by use of the NRZ line code. Eg 191.5THz will be represented as 19150
U32 jnxoptIfOChMaximumCentralFrequency	1.3.6.1.4.1.2636.3.73.1.3.2.2.1.4	Unsigned32	read-only	The maximum central frequency is the nominal single-channel frequency (in THz) on which the digital coded information of the particular optical channel is modulated by use of the NRZ line code. Eg 191.5THz will be represented as 19150
U32 jnxoptIfOChMaximumSpectralExcursion	1.3.6.1.4.1.2636.3.73.1.3.2.2.1.5	Unsigned32	read-only	This is the maximum acceptable difference between the nominal central frequency (in GHz) of the channel and the minus 15 dB points of the transmitter spectrum furthest from the nominal central frequency measured at point Ss.
I32 jnxoptIfOChMaximumTxDispersionOSNRPenalty	1.3.6.1.4.1.2636.3.73.1.3.2.2.1.6	Integer32	read-only	Defines a reference receiver that this penalty is measured with. Lowest OSNR at Ss with worst case (residual) dispersion minus the Lowest OSNR at Ss with no dispersion. Lowest OSNR at Ss with no dispersion
jnxoptIfOChSrcSinkConfigTable	1.3.6.1.4.1.2636.3.73.1.3.2.3		not-accessible	A table of paramters for the optical path from Src to Sink (Ss to Rs).
jnxoptIfOChSrcSinkConfigEntry	1.3.6.1.4.1.2636.3.73.1.3.2.3.1		not-accessible	A conceptual row that contains the optical path Src-Sink (Ss-Rs) configuration parameters for a given interface.
I32 jnxoptIfOChSrcSinkMinimumChromaticDispersion	1.3.6.1.4.1.2636.3.73.1.3.2.3.1.1	Integer32	read-only	These parameters define the minimum value of the optical path 'end to end chromatic dispersion' (in ps/nm) that the system shall be able to tolerate.
I32 jnxoptIfOChSrcSinkMaximumChromaticDispersion	1.3.6.1.4.1.2636.3.73.1.3.2.3.1.2	Integer32	read-only	These parameters define the maximum value of the optical path 'end to end chromatic dispersion' (in ps/nm) that the system shall be able to tolerate.
I32 jnxoptIfOChSrcSinkMinimumSrcOpticalReturnLoss	1.3.6.1.4.1.2636.3.73.1.3.2.3.1.3	Integer32	read-only	These parameter defines minimum optical return loss (in dB) of the cable plant at the source reference point (Src/Ss), including any connectors.
I32 jnxoptIfOChSrcSinkMaximumDiscreteReflectanceSrcToSink	1.3.6.1.4.1.2636.3.73.1.3.2.3.1.4	Integer32	read-only	Optical reflectance is defined to be the ratio of the reflected optical power pre.sent at a point, to the optical power incident to that point. Control of reflections is discussed extensively in ITU-T Rec. G.957.
I32 jnxoptIfOChSrcSinkMaximumDifferentialGroupDelay	1.3.6.1.4.1.2636.3.73.1.3.2.3.1.5	Integer32	read-only	Differential group delay (DGD) is the time difference between the fractions of a pulse that are transmitted in the two principal states of polarization of an optical signal. For distances greater than several kilometres, and assuming random (strong) polarization mode coupling, DGD in a fibre can be statistically modelled as having a Maxwellian distribution.
I32 jnxoptIfOChSrcSinkMaximumPolarisationDependentLoss	1.3.6.1.4.1.2636.3.73.1.3.2.3.1.6	Integer32	read-only	The polarisation dependent loss (PDL) is the difference (in dB) between the maximum and minimum values of the channel insertion loss (or gain) of the black-link from point SS to RS due to a variation of the state of polarization (SOP) over all SOPs.
I32 jnxoptIfOChSrcSinkMaximumInterChannelCrosstalk	1.3.6.1.4.1.2636.3.73.1.3.2.3.1.7	Integer32	read-only	Inter-channel crosstalk is defined as the ratio of total power in all of the disturbing channels to that in the wanted channel, where the wanted and disturbing channels are at different wavelengths. The parameter specify the isolation of a link conforming to the 'black-link' approach such that under the worst- case operating conditions the inter-channel crosstalk at any reference point RS is less than the maximum inter-channel crosstalk value.
I32 jnxoptIfOChSrcSinkInterFerometricCrosstalk	1.3.6.1.4.1.2636.3.73.1.3.2.3.1.8	Integer32	read-only	This parameter places a requirement on the isolation of a link conforming to the 'black-link' approach such that under the worst case operating conditions the interferometric crosstalk at any reference point RS is less than the maximum interferometric crosstalk value..
I32 jnxoptIfOChSrcSinkOpticalPathOSNRPenalty	1.3.6.1.4.1.2636.3.73.1.3.2.3.1.9	Integer32	read-only	The optical path OSNR penalty is defined as the difference between the Lowest OSNR at Rs and Lowest OSNR at Ss that meets the BER requirement.
jnxoptIfOChSinkConfigTable	1.3.6.1.4.1.2636.3.73.1.3.2.4		not-accessible	A table of OCh Sink (Rs) configuration parameters.
jnxoptIfOChSinkConfigEntry	1.3.6.1.4.1.2636.3.73.1.3.2.4.1		not-accessible	A conceptual row that contains the Sink (Rs) configuration parameters for a given interface.
I32 jnxoptIfOChSinkMinimumMeanIntputPower	1.3.6.1.4.1.2636.3.73.1.3.2.4.1.1	Integer32	read-only	The minimum values of the average received power (in dbm at point the Sink (Rs).
I32 jnxoptIfOChSinkMaximumMeanIntputPower	1.3.6.1.4.1.2636.3.73.1.3.2.4.1.2	Integer32	read-only	The maximum values of the average received power (in dbm) at point the Sink (Rs).
I32 jnxoptIfOChSinkMinimumOSNR	1.3.6.1.4.1.2636.3.73.1.3.2.4.1.3	Integer32	read-only	The minimum optical signal-to-noise ratio (OSNR) is the minimum value of the ratio of the signal power in the wanted channel to the highest noise power density in the range of the central frequency plus and minus the maximum spectral excursion.
I32 jnxoptIfOChSinkOSNRTolerance	1.3.6.1.4.1.2636.3.73.1.3.2.4.1.4	Integer32	read-only	The receiver OSNR tolerance is defined as the minimum value of OSNR at point Sink (Rs) that can be tolerated while maintaining the maximum BER of the application. Sink (Rs).
jnxoptIfOTNPMGroup	1.3.6.1.4.1.2636.3.73.1.3.3
jnxoptIfOChSinkCurrentExtTable	1.3.6.1.4.1.2636.3.73.1.3.3.1		not-accessible	A table of OCh sink etxension to the performance monitoring information for the current 15-minute interval.
jnxoptIfOChSinkCurrentExtEntry	1.3.6.1.4.1.2636.3.73.1.3.3.1.1		not-accessible	A conceptual row that contains OCh sink performance monitoring information for an interface for the current 15-minute interval.
I32 jnxoptIfOChSinkCurrentChromaticDispersion	1.3.6.1.4.1.2636.3.73.1.3.3.1.1.1	Integer32	read-only	Residual Chromatic Dispersion measured at Rx Transceiver port.
I32 jnxoptIfOChSinkCurrentOSNR	1.3.6.1.4.1.2636.3.73.1.3.3.1.1.2	Integer32	read-only	Current Optical Signal to Noise Ratio (OSNR) estimated at Rx Transceiver port .
I32 jnxoptIfOChSinkCurrentQ	1.3.6.1.4.1.2636.3.73.1.3.3.1.1.3	Integer32	read-only	'Q' factor estimated at Rx Transceiver port.
jnxoptIfOTNPMConfigTable	1.3.6.1.4.1.2636.3.73.1.3.3.2		not-accessible	A table of performance monitoring configuration for the type 'jnxoptIfOTNPMConfigLayer' layer.
jnxoptIfOTNPMConfigEntry	1.3.6.1.4.1.2636.3.73.1.3.3.2.1		not-accessible	A conceptual entry in the performance monitoring configuration for the type 'jnxoptIfOTNPMConfigLayer' layer.
JNX jnxoptIfOTNPMConfigType	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.1	JnxoptIfOTNType	not-accessible	This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
JNX jnxoptIfOTNPMConfigLayer	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.2	JnxoptIfOTNLayer	not-accessible	This parameter indicates the parameters for the table are for OTUk, ODUk, TCMn performance data. 1 - OTUk 2 - ODUk 3 - TCM The ODUk/TCM sublayer PM is not related to the black link PM management, but since this is a common PM model for the ODU/TCM layer, we may include it here.
U32 jnxoptIfOTNPMConfigTCMLevel	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.3	Unsigned32	not-accessible	This parameter indicates the TCM level (1-6) if the PM is of the type TCM. This will be 0 for OTUK/ODUK.
U32 jnxoptIfOTNPMESRInterval	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.4	Unsigned32	read-write	This parameter indicates the measurement interval for error seconds ratio.
U32 jnxoptIfOTNPMSESRInterval	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.5	Unsigned32	read-write	This parameter indicates the measurement interval for severely error seconds ratio.
U32 jnxoptIfOTNPMValidIntervals	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.6	Unsigned32	read-only	The number of contiguous 15 minute intervals for which valid PM data is available for the particular interface.
U32 jnxoptIfOTNPM15MinBip8Threshold	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.7	Unsigned32	read-write	The number of Bip8 encountered by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshBip8TCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM15MinESsThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.8	Unsigned32	read-write	The number of ES encountered by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshEsTCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM15MinSESsThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.9	Unsigned32	read-write	The number of SES encountered by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshSESTCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM15MinUASsThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.10	Unsigned32	read-write	The number of UAS encountered by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshUASTCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM15MinBBEsThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.11	Unsigned32	read-write	The number of UAS encountered by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshBBETCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM24HourBip8Threshold	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.12	Unsigned32	read-write	The number of Bip8 encountered by the interface within any given 24 Hour performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshBip8TCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM24HourESsThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.13	Unsigned32	read-write	The number of ES encountered by the interface within any given 24 hour performance data collection period, which causes the SNMP agent to send jnxoptIf24HourThreshEsTCA. One notification will be sent per 24 hour per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM24HourSESsThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.14	Unsigned32	read-write	The number of SES encountered by the interface within any given 24 hour performance data collection period, which causes the SNMP agent to send jnxoptIf24HourThreshSESsTCA. One notification will be sent per 24 hour per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM24HourUASsThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.15	Unsigned32	read-write	The number of SES encountered by the interface within any given 24 hour performance data collection period, which causes the SNMP agent to send jnxoptIf24HourThreshUASsTCA. One notification will be sent per 24 hour per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM24HourBBEsThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.16	Unsigned32	read-write	The number of BBE encountered by the interface within any given 24 hour performance data collection period, which causes the SNMP agent to send jnxoptIf24HourThreshBBEsTCA. One notification will be sent per 24 hour per interface. A value of `0' will disable the notification.
T/F jnxoptIfOTNPMBip8EnableTCA	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.17	TruthValue	read-write	Enable TCA's - 15minute and 24hr for Bip8
T/F jnxoptIfOTNPMESsEnableTCA	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.18	TruthValue	read-write	Enable TCA's - 15minute and 24hr for ESs
T/F jnxoptIfOTNPMSESsEnableTCA	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.19	TruthValue	read-write	Enable TCA's - 15minute and 24hr for SESs
T/F jnxoptIfOTNPMUASsEnableTCA	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.20	TruthValue	read-write	Enable TCA's - 15minute and 24hr for UASs
T/F jnxoptIfOTNPMBBEsEnableTCA	1.3.6.1.4.1.2636.3.73.1.3.3.2.1.21	TruthValue	read-write	Enable TCA's - 15minute and 24hr for BBEs
jnxoptIfOTNPMCurrentTable	1.3.6.1.4.1.2636.3.73.1.3.3.3		not-accessible	A table for the Performance monitoring Current Table.
jnxoptIfOTNPMCurrentEntry	1.3.6.1.4.1.2636.3.73.1.3.3.3.1		not-accessible	A conceptual entry in the Near end or Far End performance monitoring Current table for the type 'jnxoptIfOTNPMCurrentLayer' layer.
JNX jnxoptIfOTNPMCurrentType	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.1	JnxoptIfOTNType	not-accessible	This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
JNX jnxoptIfOTNPMCurrentLayer	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.2	JnxoptIfOTNLayer	not-accessible	This parameter indicates the parameters for the table are for OTUk, ODUk, TCMn performance data. 1 - OTUk (OCh which is used for the black link) 2 - ODUk 3 - TCM The ODUk/TCM sublayer PM is not related to the black link PM management, but since this is a common PM model for the ODU/TCM layer, we may include it here.
U32 jnxoptIfOTNPMCurrentTCMLevel	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.3	Unsigned32	not-accessible	This parameter indicates the TCM level (1-6) if the PM is of the type TCM. This will be 0 for OTUK/ODUK.
T/F jnxoptIfOTNPMCurrentSuspectedFlag	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.4	TruthValue	read-only	If true, the data in this entry may be unreliable.
U32 jnxoptIfOTNPMCurrentBip8	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.5	Unsigned32	read-only	Number of Failures occurred in an observation period.
U32 jnxoptIfOTNPMCurrentESs	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.6	Unsigned32	read-only	This is the number of seconds in which one or more bits are in error or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
U32 jnxoptIfOTNPMCurrentSESs	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.7	Unsigned32	read-only	The number of seconds which have a severe error. This is the number of seconds in which the bit-error ratio = 1x10Eminus3 or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
U32 jnxoptIfOTNPMCurrentUASs	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.8	Unsigned32	read-only	It is the number of unavailable seconds. A period of unavailable time begins at the onset of ten consecutive SES events. These ten seconds are considered to be part of unavailable time. A new period of available time begins at the onset of ten consecutive non-SES events. These ten seconds are considered to be part of available time.
U32 jnxoptIfOTNPMCurrentBBEs	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.9	Unsigned32	read-only	An errored block not occurring as part of an SES.
U32 jnxoptIfOTNPMCurrentESR	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.10	Unsigned32	read-only	The ratio of ES in available time to total seconds in available time during a fixed measurement interval.
U32 jnxoptIfOTNPMCurrentSESR	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.11	Unsigned32	read-only	The ratio of SES in available time to total seconds in available time during a fixed measurement interval.
U32 jnxoptIfOTNPMCurrentBBER	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.12	Unsigned32	read-only	The ratio of BER in available time to total seconds in available time during a fixed measurement interval.
U32 jnxoptIfOTNPMCurrentElapsedTime	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.13	Unsigned32	read-only	Time elapsed for this 15 minute interval
I32 jnxoptIfOTNPMCurSuspectReason	1.3.6.1.4.1.2636.3.73.1.3.3.3.1.14	Integer32	read-only	If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - interval too short secs 910 8 - near end unavailable 9 - far end unavailable 10 - partial data 11 - missing intervals due to restarts
jnxoptIfOTNPMIntervalTable	1.3.6.1.4.1.2636.3.73.1.3.3.4		not-accessible	A Performance monitoring Interval Table.
jnxoptIfOTNPMIntervalEntry	1.3.6.1.4.1.2636.3.73.1.3.3.4.1		not-accessible	A conceptual entry in the Near end or Far End performance monitoring Interval table for the type 'jnxoptIfOTNPMIntervalLayer' layer.
JNX jnxoptIfOTNPMIntervalType	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.1	JnxoptIfOTNType	not-accessible	This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
JNX jnxoptIfOTNPMIntervalLayer	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.2	JnxoptIfOTNLayer	not-accessible	This parameter indicates the parameters for the table are for OTUk, ODUk, TCMn performance data. 1 - OTUk 2 - ODUk 3 - TCM The ODUk/TCM sublayer PM is not related to the black link PM management, but since this is a common PM model for the ODU/TCM layer, we may include it here.
U32 jnxoptIfOTNPMIntervalTCMLevel	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.3	Unsigned32	not-accessible	This parameter indicates the TCM level (1-6) if the PM is of the type TCM. This will be 0 for OTUK/ODUK.
U32 jnxoptIfOTNPMIntervalNumber	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.4	Unsigned32	not-accessible	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the 15 minutes interval completed 23 hours and 45 minutes prior to interval 1.
T/F jnxoptIfOTNPMIntervalSuspectedFlag	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.5	TruthValue	read-only	If true, the data in this entry may be unreliable.
U32 jnxoptIfOTNPMIntervalBip8	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.6	Unsigned32	read-only	Number of Failures occurred in an observation period.
U32 jnxoptIfOTNPMIntervalESs	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.7	Unsigned32	read-only	It is a one-second period in which one or more bits are in error or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
U32 jnxoptIfOTNPMIntervalSESs	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.8	Unsigned32	read-only	The number of seconds which have a severe error. It is a one-second period which has a bit-error ratio = 1x10Eminus3 or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
U32 jnxoptIfOTNPMIntervalUASs	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.9	Unsigned32	read-only	It is the number of unavailable seconds in this 15 minute interval. A period of unavailable time begins at the onset of ten consecutive SES events. These ten seconds are considered to be part of unavailable time. A new period of available time begins at the onset of ten consecutive non-SES events. These ten seconds are considered to be part of available time.
U32 jnxoptIfOTNPMIntervalBBEs	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.10	Unsigned32	read-only	An errored block not occurring as part of an SES.
U32 jnxoptIfOTNPMIntervalESR	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.11	Unsigned32	read-only	The ratio of ES in available time to total seconds in available time during a fixed measurement interval.
U32 jnxoptIfOTNPMIntervalSESR	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.12	Unsigned32	read-only	The ratio of SES in available time to total seconds in available time during a fixed measurement interval.
U32 jnxoptIfOTNPMIntervalBBER	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.13	Unsigned32	read-only	The ratio of BBE in available time to total seconds in available time during a fixed measurement interval.
DAT jnxoptIfOTNPMIntervalTimeStamp	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.14	DateAndTime	read-only	Time stamp of this interval.
I32 jnxoptIfOTNPMIntSuspectReason	1.3.6.1.4.1.2636.3.73.1.3.3.4.1.15	Integer32	read-only	If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - interval too short secs 910 8 - near end unavailable 9 - far end unavailable 10 - partial data 11 - missing intervals due to restarts
jnxoptIfOTNPMCurrentDayTable	1.3.6.1.4.1.2636.3.73.1.3.3.5		not-accessible	A Performance monitoring Current Day Table.
jnxoptIfOTNPMCurrentDayEntry	1.3.6.1.4.1.2636.3.73.1.3.3.5.1		not-accessible	A conceptual entry in the Near end or Far End performance monitoring Current day table for the type 'jnxoptIfOTNPMCurrentDayLayer' layer.
JNX jnxoptIfOTNPMCurrentDayType	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.1	JnxoptIfOTNType	not-accessible	This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
JNX jnxoptIfOTNPMCurrentDayLayer	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.2	JnxoptIfOTNLayer	not-accessible	This parameter indicates the parameters for the table are for OTUk, ODUk, TCMn performance data. 1 - OTUk 2 - ODUk 3 - TCM The ODUk/TCM sublayer PM is not related to the black link PM management, but since this is a common PM model for the ODU/TCM layer, we may include it here.
U32 jnxoptIfOTNPMCurrentDayTCMLevel	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.3	Unsigned32	not-accessible	This parameter indicates the TCM level (1-6) if the PM is of the type TCM. This will be 0 for OTUK/ODUK.
T/F jnxoptIfOTNPMCurrentDaySuspectedFlag	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.4	TruthValue	read-only	If true, the data in this entry may be unreliable.
U32 jnxoptIfOTNPMCurrentDayBip8	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.5	Unsigned32	read-only	Number of Failures occurred in an observation period.
U32 jnxoptIfOTNPMCurrentDayESs	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.6	Unsigned32	read-only	The number of seconds which have an error. It is a one-second period in which one or more bits are in error or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
U32 jnxoptIfOTNPMCurrentDaySESs	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.7	Unsigned32	read-only	The number of seconds which have a severe error. It is a one-second period which has a bit-error ratio = 1x10Eminus3 or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
U32 jnxoptIfOTNPMCurrentDayUASs	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.8	Unsigned32	read-only	It is the number of unavailable seconds in the cunrrent day. A period of unavailable time begins at the onset of ten consecutive SES events. These ten seconds are considered to be part of unavailable time. A new period of available time begins at the onset of ten consecutive non-SES events. These ten seconds are considered to be part of available time.
U32 jnxoptIfOTNPMCurrentDayBBEs	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.9	Unsigned32	read-only	An errored block not occurring as part of an SES.
U32 jnxoptIfOTNPMCurrentDayESR	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.10	Unsigned32	read-only	The ratio of ES in available time to total seconds in available time during a fixed measurement interval.
U32 jnxoptIfOTNPMCurrentDaySESR	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.11	Unsigned32	read-only	The ratio of SES in available time to total seconds in available time during a fixed measurement interval.
U32 jnxoptIfOTNPMCurrentDayBBER	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.12	Unsigned32	read-only	The ratio of BBE in available time to total seconds in available time during a fixed measurement interval.
U32 jnxoptIfOTNPMCurrentDayElapsedTime	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.13	Unsigned32	read-only	Time elapsed for current day
I32 jnxoptIfOTNPMCurDaySuspectReason	1.3.6.1.4.1.2636.3.73.1.3.3.5.1.14	Integer32	read-only	If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - partial data 7 - one or more intervals are invaild
jnxoptIfOTNPMPrevDayTable	1.3.6.1.4.1.2636.3.73.1.3.3.6		not-accessible	A Performance monitoring Previous Day Table.
jnxoptIfOTNPMPrevDayEntry	1.3.6.1.4.1.2636.3.73.1.3.3.6.1		not-accessible	A conceptual entry in the Near end or Far End performance monitoring previous day table for the type 'jnxoptIfOTNPMPrevDayLayer' layer.
JNX jnxoptIfOTNPMPrevDayType	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.1	JnxoptIfOTNType	not-accessible	This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
JNX jnxoptIfOTNPMPrevDayLayer	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.2	JnxoptIfOTNLayer	not-accessible	This parameter indicates the parameters for the table are for OTUk, ODUk, TCMn performance data. 1 - OTUk 2 - ODUk 3 - TCM The ODUk/TCM sublayer PM is not related to the black link PM management, but since this is a common PM model for the ODU/TCM layer, we may include it here.
U32 jnxoptIfOTNPMPrevDayTCMLevel	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.3	Unsigned32	not-accessible	This parameter indicates the TCM level (1-6) if the PM is of the type TCM.
T/F jnxoptIfOTNPMPrevDaySuspectedFlag	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.4	TruthValue	read-only	If true, the data in this entry may be unreliable.
U32 jnxoptIfOTNPMPrevDayBip8	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.5	Unsigned32	read-only	Number of pre FEC failures occurred in an observation period.
U32 jnxoptIfOTNPMPrevDayESs	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.6	Unsigned32	read-only	The number of seconds which have an error. It is a one-second period in which one or more bits are in error or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
U32 jnxoptIfOTNPMPrevDaySESs	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.7	Unsigned32	read-only	The number of seconds which have a severe error. A severely errored second, is a one-second period which has a bit-error ratio = 1x10Eminus3 or during which Loss of Signal (LOS) or Alarm Indication Signal (AIS) is detected.
U32 jnxoptIfOTNPMPrevDayUASs	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.8	Unsigned32	read-only	It is the number of unavailable seconds in the previous day. A period of unavailable time begins at the onset of ten consecutive SES events. These ten seconds are considered to be part of unavailable time. A new period of available time begins at the onset of ten consecutive non-SES events. These ten seconds are considered to be part of available time.
U32 jnxoptIfOTNPMPrevDayBBEs	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.9	Unsigned32	read-only	An errored block not occurring as part of an SES.
U32 jnxoptIfOTNPMPrevDayESR	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.10	Unsigned32	read-only	The ratio of ES in available time to total seconds in available time during a fixed measurement interval.
U32 jnxoptIfOTNPMPrevDaySESR	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.11	Unsigned32	read-only	The ratio of SES in available time to total seconds in available time during a fixed measurement interval.
U32 jnxoptIfOTNPMPrevDayBBER	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.12	Unsigned32	read-only	The ratio of BBE in available time to total seconds in available time during a fixed measurement interval.
DAT jnxoptIfOTNPMPrevDayTimeStamp	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.13	DateAndTime	read-only	Time stamp of this interval.
I32 jnxoptIfOTNPMPrevDaySuspectReason	1.3.6.1.4.1.2636.3.73.1.3.3.6.1.14	Integer32	read-only	If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - clock shift detected 4 - cleared by user 5 - partial data 6 - missing intervals due to restarts 7 - one or more intervals are invaild
jnxoptIfOTNPMFECConfigTable	1.3.6.1.4.1.2636.3.73.1.3.3.7		not-accessible	A table of performance monitoring FEC configuration.
jnxoptIfOTNPMFECConfigEntry	1.3.6.1.4.1.2636.3.73.1.3.3.7.1		not-accessible	A conceptual entry in the performance monitoring FEC configuration layer.
JNX jnxoptIfOTNPMFECConfigType	1.3.6.1.4.1.2636.3.73.1.3.3.7.1.1	JnxoptIfOTNType	not-accessible	This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
U32 jnxoptIfOTNPMFECValidIntervals	1.3.6.1.4.1.2636.3.73.1.3.3.7.1.2	Unsigned32	read-only	The number of contiguous 15 minute intervals for which valid FEC PM data is available for the particular interface.
U32 jnxoptIfOTNPM15MinPreFECBERMantissaThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.7.1.3	Unsigned32	read-write	BER (mantissa) by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshPreFECBERTCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM15MinPreFECBERExponentThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.7.1.4	Unsigned32	read-write	The Pre FEC BER (exponent) by the interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send jnxoptIf15MinThreshPreFECBERTCA. One notification will be sent per interval per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM24HourPreFECBERMantissaThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.7.1.5	Unsigned32	read-write	BER (mantissa) by the interface within any given 24 Hour performance data collection period, which causes the SNMP agent to send jnxoptIf5s24Hour15MinThreshPreFECBERTCA. One notification will be sent per 24 hour period per interface. A value of `0' will disable the notification.
U32 jnxoptIfOTNPM24HourPreFECBERExponentThreshold	1.3.6.1.4.1.2636.3.73.1.3.3.7.1.6	Unsigned32	read-write	The Pre FEC BER (exponent) by the interface within any given 24 Hour performance data collection period, which causes the SNMP agent to send jnxoptIf5s24Hour15MinThreshPreFECBERTCA. One notification will be sent per 24 hour period per interface. A value of `0' will disable the notification.
T/F jnxoptIfOTNPMFECBEREnableTCA	1.3.6.1.4.1.2636.3.73.1.3.3.7.1.7	TruthValue	read-write	Enable TCA's - 15minute and 24hr for FEC BER
jnxoptIfOTNPMFECCurrentTable	1.3.6.1.4.1.2636.3.73.1.3.3.8		not-accessible	A Performance monitoring FEC Current Table.
jnxoptIfOTNPMFECCurrentEntry	1.3.6.1.4.1.2636.3.73.1.3.3.8.1		not-accessible	A conceptual entry in the Near end or Far End performance monitoring FEC current table.
JNX jnxoptIfOTNPMFECCurrentType	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.1	JnxoptIfOTNType	not-accessible	This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
T/F jnxoptIfOTNPMFECCurrentSuspectedFlag	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.2	TruthValue	read-only	If true, the data in this entry may be unreliable.
C64 jnxoptIfOTNPMCurrentFECCorrectedErrEx	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.3	Counter64	read-only	The number of bits corrected by the FEC are counted in the interval.
C64 jnxoptIfOTNPMCurrentFECUncorrectedWords	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.4	Counter64	read-only	The number of un-corrected words by the FEC are counted over the interval.
U32 jnxoptIfOTNPMCurrentFECBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.5	Unsigned32	read-only	The number of Errored bits at receiving side before the FEC function counted over one second .. mantissa.
U32 jnxoptIfOTNPMCurrentFECBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.6	Unsigned32	read-only	The number of Errored bits at receiving side before the FEC function counted over one second .. exponent (eg -1).
U32 jnxoptIfOTNPMCurrentFECMinBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.7	Unsigned32	read-only	The minimum number of Errored bits at receiving side before the FEC function counted over one second .. mantissa.
U32 jnxoptIfOTNPMCurrentFECMinBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.8	Unsigned32	read-only	The minimum number of Errored bits at receiving side before the FEC function counted over one second .. exponent (eg -1).
U32 jnxoptIfOTNPMCurrentFECMaxBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.9	Unsigned32	read-only	The maximum number of Errored bits at receiving side before the FEC function counted over one second .. mantissa.
U32 jnxoptIfOTNPMCurrentFECMaxBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.10	Unsigned32	read-only	The maximum number of Errored bits at receiving side before the FEC function counted over one second .. exponent (eg -1).
U32 jnxoptIfOTNPMCurrentFECAvgBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.11	Unsigned32	read-only	The average number of Errored bits at receiving side before the FEC function counted over one second .. mantissa.
U32 jnxoptIfOTNPMCurrentFECAvgBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.12	Unsigned32	read-only	The average number of Errored bits at receiving side before the FEC function counted over one second .. exponent (eg -1).
U32 jnxoptIfOTNPMCurrentFECElapsedTime	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.13	Unsigned32	read-only	Time elapsed for this 15 minute interval.
I32 jnxoptIfOTNPMFECCurSuspectReason	1.3.6.1.4.1.2636.3.73.1.3.3.8.1.14	Integer32	read-only	If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - interval too short secs 910 8 - near end unavailable 9 - far end unavailable 10 - partial data 11 - missing intervals due to restarts
jnxoptIfOTNPMFECIntervalTable	1.3.6.1.4.1.2636.3.73.1.3.3.9		not-accessible	A Performance monitoring FEC Interval Table.
jnxoptIfOTNPMFECIntervalEntry	1.3.6.1.4.1.2636.3.73.1.3.3.9.1		not-accessible	A conceptual entry in the Near end or Far End performance monitoring FEC interval table.
JNX jnxoptIfOTNPMFECIntervalType	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.1	JnxoptIfOTNType	not-accessible	This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
U32 jnxoptIfOTNPMFECIntervalNumber	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.2	Unsigned32	not-accessible	A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the 15 minutes interval completed 23 hours and 45 minutes prior to interval 1.
T/F jnxoptIfOTNPMFECIntervalSuspectedFlag	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.3	TruthValue	read-only	If true, the data in this entry may be unreliable.
C64 jnxoptIfOTNPMIntervalFECCorrectedErr	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.4	Counter64	read-only	The number of bits corrected by the FEC are counted in the interval.
C64 jnxoptIfOTNPMIntervalFECUncorrectedWords	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.5	Counter64	read-only	The number of words un-corrected words by the FEC are counted over the interval.
U32 jnxoptIfOTNPMIntervalMinFECBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.6	Unsigned32	read-only	The minimun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the minimum Pre FEC BER in the current 24hour period.
U32 jnxoptIfOTNPMIntervalMinFECBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.7	Unsigned32	read-only	The minimun bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the minimum Pre FEC BER in the current 24hour period.
U32 jnxoptIfOTNPMIntervalMaxFECBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.8	Unsigned32	read-only	The maximun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the maximum Pre FEC BER in the current 24hour period.
U32 jnxoptIfOTNPMIntervalMaxFECBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.9	Unsigned32	read-only	The maximun bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the maximum Pre FEC BER in the current 24hour period.
U32 jnxoptIfOTNPMIntervalAvgFECBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.10	Unsigned32	read-only	The average bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the average Pre FEC BER in the current 24hour period.
U32 jnxoptIfOTNPMIntervalAvgFECBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.11	Unsigned32	read-only	The average bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the average Pre FEC BER in the current 24hour period.
DAT jnxoptIfOTNPMFECIntervalTimeStamp	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.12	DateAndTime	read-only	Time stamp of this interval.
I32 jnxoptIfOTNPMFECIntSuspectReason	1.3.6.1.4.1.2636.3.73.1.3.3.9.1.13	Integer32	read-only	If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - interface disabled 4 - clock shift detected 5 - cleared by user 6 - interval too short secs 910 8 - near end unavailable 9 - far end unavailable 10 - partial data 11 - missing intervals due to restarts
jnxoptIfOTNPMFECCurrentDayTable	1.3.6.1.4.1.2636.3.73.1.3.3.10		not-accessible	A Performance monitoring FEC current day table.
jnxoptIfOTNPMFECCurrentDayEntry	1.3.6.1.4.1.2636.3.73.1.3.3.10.1		not-accessible	A conceptual entry in the Near end or Far End performance monitoring FEC current day table.
JNX jnxoptIfOTNPMFECCurrentDayType	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.1	JnxoptIfOTNType	not-accessible	This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
T/F jnxoptIfOTNPMFECCurrentDaySuspectedFlag	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.2	TruthValue	read-only	If true, the data in this entry may be unreliable.
C64 jnxoptIfOTNPMCurrentDayFECCorrectedErr	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.3	Counter64	read-only	The number of bits corrected by the FEC are counted in the interval.
C64 jnxoptIfOTNPMCurrentDayFECUncorrectedWords	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.4	Counter64	read-only	The number of words un-corrected by the FEC are counted over the Day.
U32 jnxoptIfOTNPMCurrentDayMinFECBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.5	Unsigned32	read-only	The minimun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the minimum PreFEC BER in the current 24hour period.
U32 jnxoptIfOTNPMCurrentDayMinFECBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.6	Unsigned32	read-only	The minimun bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the minimum PreFEC BER in the current 24hour period.
U32 jnxoptIfOTNPMCurrentDayMaxFECBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.7	Unsigned32	read-only	The maximun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the maximum PreFEC BER in the current 24hour period.
U32 jnxoptIfOTNPMCurrentDayMaxFECBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.8	Unsigned32	read-only	The maximun bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the maximum PreFEC BER in the current 24hour period.
U32 jnxoptIfOTNPMCurrentDayAvgFECBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.9	Unsigned32	read-only	The average bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the average PreFEC BER in the current 24hour period.
U32 jnxoptIfOTNPMCurrentDayAvgFECBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.10	Unsigned32	read-only	The average bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the average PreFEC BER in the current 24hour period.
U32 jnxoptIfOTNPMFECCurrentDayElapsedTime	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.11	Unsigned32	read-only	Time elapsed for current day.
I32 jnxoptIfOTNPMFECCurDaySuspectReason	1.3.6.1.4.1.2636.3.73.1.3.3.10.1.12	Integer32	read-only	If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - clock shift detected 4 - cleared by user 5 - partial data 6 - missing intervals due to restarts 7 - one or more intervals are invaild
jnxoptIfOTNPMFECPrevDayTable	1.3.6.1.4.1.2636.3.73.1.3.3.11		not-accessible	A Performance monitoring FEC previous day table.
jnxoptIfOTNPMFECPrevDayEntry	1.3.6.1.4.1.2636.3.73.1.3.3.11.1		not-accessible	A conceptual entry in the Near end or Far End performance monitoring FEC previous day table.
JNX jnxoptIfOTNPMFECPrevDayType	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.1	JnxoptIfOTNType	not-accessible	This parameter indicates the parameters for the table are for the Near End or Far End performance data. 1 - Near End 2 - Far End
T/F jnxoptIfOTNPMFECPrevDaySuspectedFlag	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.2	TruthValue	read-only	If true, the data in this entry may be unreliable.
C64 jnxoptIfOTNPMPrevDayFECCorrectedErr	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.3	Counter64	read-only	The number of bits corrected by the FEC are counted in the previous day.
C64 jnxoptIfOTNPMPrevDayFECUncorrectedWords	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.4	Counter64	read-only	The number of un-corrected words by the FEC are counted over the previous Day.
U32 jnxoptIfOTNPMPrevDayMinFECBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.5	Unsigned32	read-only	The maximun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the maximum Pre FEC BER in the previous 24hour period.
U32 jnxoptIfOTNPMPrevDayMinFECBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.6	Unsigned32	read-only	The minimun bit error rate at receiving side before the FEC function counted over one second .. exponent. This is the maximum Pre FEC BER in the previous 24hour period.
U32 jnxoptIfOTNPMPrevDayMaxFECBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.7	Unsigned32	read-only	The maximun bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the maximum Pre FEC BER in the previous 24hour period (mantissa).
U32 jnxoptIfOTNPMPrevDayMaxFECBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.8	Unsigned32	read-only	The maximun bit error rate at receiving side before the FEC function counted over one second .. exponent (eg -3). This is the maximum Pre FEC BER in the previous 24hour period.
U32 jnxoptIfOTNPMPrevDayAvgFECBERMantissa	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.9	Unsigned32	read-only	The average bit error rate at receiving side before the FEC function counted over one second .. mantissa. This is the average Pre FEC BER during the previous 24hour period (mantissa).
U32 jnxoptIfOTNPMPrevDayAvgFECBERExponent	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.10	Unsigned32	read-only	The average bit error rate at receiving side before the FEC function counted over one second .. exponent (eg -3). This is the average Pre FEC BER during the previous 24hour period.
DAT jnxoptIfOTNPMFECPrevDayTimeStamp	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.11	DateAndTime	read-only	Time stamp for the Prev day.
I32 jnxoptIfOTNPMFECPrevDaySuspectReason	1.3.6.1.4.1.2636.3.73.1.3.3.11.1.12	Integer32	read-only	If SuspectedFlag is true, the reson for the PM data being suspect. 0 - not applicable 1 - unknown 2 - new object 3 - clock shift detected 4 - cleared by user 5 - partial data 6 - missing intervals due to restarts 7 - one or more intervals are invaild
jnxoptIfOTNAlarm	1.3.6.1.4.1.2636.3.73.1.3.4
jnxoptIfOTNAlarmTable	1.3.6.1.4.1.2636.3.73.1.3.4.1		not-accessible	A table of alarm entries.
jnxoptIfOTNAlarmEntry	1.3.6.1.4.1.2636.3.73.1.3.4.1.1		not-accessible	A conceptual entry in the alarm table.
JNX jnxoptIfOTNAlarmLocation	1.3.6.1.4.1.2636.3.73.1.3.4.1.1.1	JnxoptIfOTNType	accessible-for-notify	The object identifies indicates if this entry was for Near end/Far end.
JNX jnxoptIfOTNAlarmDirection	1.3.6.1.4.1.2636.3.73.1.3.4.1.1.2	JnxoptIfOTNDirection	accessible-for-notify	The object identifies indicates if this entry was for for the Tx/Rx or both.
JNX jnxoptIfOTNAlarmLayer	1.3.6.1.4.1.2636.3.73.1.3.4.1.1.3	JnxoptIfOTNLayer	accessible-for-notify	This specifies which sublayer this alarm is for.
U32 jnxoptIfOTNAlarmTCMLevel	1.3.6.1.4.1.2636.3.73.1.3.4.1.1.4	Unsigned32	accessible-for-notify	TCM level 1-6 of the alarm. It will be 0 if alarm sublayer is OCh, OTUk or ODUk.
JNX jnxoptIfOTNOChOTUkAlarmType	1.3.6.1.4.1.2636.3.73.1.3.4.1.1.5	JnxoptIfOTNOChAlarms	accessible-for-notify	This specifies the type of alarm of the sublayer 'jnxoptIfOTNAlarmLayer' for OCh/OTUk .
JNX jnxoptIfOTNAlarmSeverity	1.3.6.1.4.1.2636.3.73.1.3.4.1.1.6	JnxoptIfOTNAlarmSeverity	accessible-for-notify	The object identifies the severity of the last alarm/alert that most recently was set or cleared.
DAT jnxoptIfOTNAlarmDate	1.3.6.1.4.1.2636.3.73.1.3.4.1.1.7	DateAndTime	accessible-for-notify	This specifies the date and time when this alarm occurred.
JNX jnxoptIfOTNODUkTcmAlarmType	1.3.6.1.4.1.2636.3.73.1.3.4.1.1.8	JnxoptIfOTNODUkTcmAlarms	accessible-for-notify	This specifies the type of alarm of the sublayer 'jnxoptIfOTNAlarmLayer' for ODUk/TCM .

RFC description

Juniper optical interface black link extension for G.698.2 compliance and optical performance monitoring.

Start monitoring Juniper Networks DWDM/optical transport platform (Black Link/G.698.2 extension) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download JNX-OPT-IF-EXT-MIB