CTRON-SFPS-BASE-MIB

All MIBs › CTRON-SFPS-BASE-MIB

Category: Vendor: Cabletron/Enterasys

Description: Provides base objects for Cabletron SFPS (SecureFast Packet Switch) virtual networking infrastructure.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CTRON-SFPS-BASE-MIB?

CTRON-SFPS-BASE-MIB is a Cabletron (Enterasys) enterprise MIB that defines the base object set for the SecureFast Packet Switch (SFPS), a virtual-networking/VLAN switching architecture used in Cabletron's SecureFast product line. It exposes a control-processor resource table describing named CP (control processor) resources, their administrative/operational status, and resource utilization figures such as points-in and points-used counters. For hardware/software status monitoring, sfpsCPResourcesTableOperStatus and sfpsCPResourcesTableAdminStatus reveal whether a given control-processor resource is enabled and functioning, sfpsCPResourcesTableStateTime tracks how long it has held that state, and sfpsCPResourcesTablePtsUsed versus sfpsCPResourcesTablePtsIn shows resource consumption that could signal exhaustion. It is a proprietary base MIB for Cabletron's SecureFast virtual-networking architecture and is typically used together with the related SFPS call, connection, and packet-manager MIBs rather than in isolation. It is deployed on Cabletron SecureFast Packet Switch devices providing switched virtual-LAN services, and administrators can download the CTRON-SFPS-BASE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CTRON-SFPS-BASE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cabletron SecureFast Packet Switch (SFPS)

Monitoring Examples

An administrator would walk sfpsCPResourcesTable entries, checking sfpsCPResourcesTableAdminStatus against sfpsCPResourcesTableOperStatus for each named resource (sfpsCPResourcesTableName) to confirm it is enabled and actually operational. Comparing sfpsCPResourcesTablePtsUsed to sfpsCPResourcesTablePtsIn for a resource reveals how close that control-processor resource is to exhaustion, an early warning before new virtual circuits fail to establish. sfpsCPResourcesTableStateTime helps the admin spot a resource that has unexpectedly changed state recently, pointing to a possible fault.

What Can Be Monitored

control-processor resource admin/operational status
resource points-in vs. points-used
resource state duration
flood/resolve policy configuration

Imported Objects

From CTRON-SFPS-INCLUDE-MIB

sfpsATalkAMRVLANControl	OBJECT-IDENTITY
sfpsBlockSource	OBJECT-IDENTITY
sfpsBlockSourceAPI	OBJECT-IDENTITY
sfpsBlockSourceExclude	OBJECT-IDENTITY
sfpsBlockSourceOnly	OBJECT-IDENTITY
sfpsBlockSourcePort	OBJECT-IDENTITY
sfpsBlockSourceStats	OBJECT-IDENTITY
sfpsCPResources	OBJECT-IDENTITY
sfpsCSPControl	OBJECT-IDENTITY
sfpsDHCPServerVLAN	OBJECT-IDENTITY
sfpsServiceCenter	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

TimeTicks

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
sfpsCPResourcesTable	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1		not-accessible	This table contains all Call Processors registered with the CPResources Table and is indexed by the Call Processor id.
sfpsCPResourcesTableEntry	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1		not-accessible	Each entry contains information pertaining to a Call Processor.
INT sfpsCPResourcesTableId	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.1	INTEGER	read-only	Call Processor id used to index into the table.
STR sfpsCPResourcesTableName	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.2	DisplayString	read-only	The name of the associated Call Processor.
INT sfpsCPResourcesTableOperStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.3	INTEGER	read-only	Operational state of entry.
INT sfpsCPResourcesTableAdminStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.4	INTEGER	read-only	This value represents the current administration status of the associated Call Processor. When enabled(3) the Call Processor is still allowed to call process packets. When this value is disabled(2) the call processor will not process any packets.
TIK sfpsCPResourcesTableStateTime	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.5	TimeTicks	read-only	The last time that this Call Processor has changed states.
INT sfpsCPResourcesTablePtsIn	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.6	INTEGER	read-only	The number of packets that have been sent to this Call Processor to be handled.
INT sfpsCPResourcesTablePtsUsed	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.7	INTEGER	read-only	The number of packets that have been sent to this Call Processor and accepted for the purpose of processing.
INT sfpsCPResourcesTablePolicyFlood	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.8	INTEGER	read-only	Number of packets flooded due to Policy.
INT sfpsCPResourcesResolveFlood	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.9	INTEGER	read-only	Number of packets flooded due to not able to Resolve.
INT sfpsCPResourcesConnectOK	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.10	INTEGER	read-only	Number of packets that caused a successful connect.
INT sfpsCPResourcesDuplicate	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.11	INTEGER	read-only	Number of packets that were duplicates of an existing call.
INT sfpsCPResourcesDiscoverOnly	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.12	INTEGER	read-only	Number of packets that the switch only discovered information.
INT sfpsCPResourcesDiscoverError	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.13	INTEGER	read-only	Number of packets that the switch could not discover information. Something was wrong with the packet.
INT sfpsCPResourcesResolveFail	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.14	INTEGER	read-only	Number of packets which caused the Resolve to fail. The fail is due to no vlan information was returned.
INT sfpsCPResourcesResolveError	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.15	INTEGER	read-only	Number of packets which caused the Resolve to return an error. An error could be caused by a bad packet.
INT sfpsCPResourcesPolicyFail	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.16	INTEGER	read-only	Number of packets which caused the Policy to fail. The fail is caused because the switch has no information on the vlan(s) returned by Resolve.
INT sfpsCPResourcesPolicyError	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.17	INTEGER	read-only	Number of packets which caused the Policy to return an error. An error could be caused by a bad packet.
INT sfpsCPResourcesConnectFail	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.18	INTEGER	read-only	Number of packets that caused the Connect to fail.
INT sfpsCPResourcesConnectFlood	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.19	INTEGER	read-only	Number of packets that caused the Connect to flood.
INT sfpsCPResourcesConnectError	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.20	INTEGER	read-only	Number of packets that caused the Connect to return an error.
TIK sfpsCPResourcesConfigTime	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.21	TimeTicks	read-only	Number of time ticks since the last configuration change.
INT sfpsCPResourcesNeedFlood	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.22	INTEGER	read-only	Set to enabled(1)/disabled(0) if the BaseNeedFlood attribute is desired. If disabled, then an attempt to resolve is performed.
INT sfpsCPResourcesNeedResolve	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.23	INTEGER	read-only	Set to enabled(1)/disabled(0) if the Resoolve attribute is desired.
INT sfpsCPResourcesNeedDiscover	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.24	INTEGER	read-only	Set to enabled(1)/disabled(0) if the Discover attribute is desired.
INT sfpsCPResourcesDiscoverAll	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.25	INTEGER	read-only	Set to enabled(1)/disabled(0) if the DiscoverAll attribute is desired.
INT sfpsCPResourcesNeedProxyOut	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.26	INTEGER	read-only	Set to enabled(1)/disabled(0) if the Proxy Forward attribute is desired.
INT sfpsCPResourcesNeedProxyIn	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.27	INTEGER	read-only	Set to enabled(1)/disabled(0) if the Proxy Back attribute is desired.
INT sfpsCPResourcesNeedFilter	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.28	INTEGER	read-only	Set to enabled(1)/disabled(0) if the Filter attribute is desired.
INT sfpsCPResourcesAcceptRate	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.29	INTEGER	read-only	The number of packets per second that have been sent to this Call Processor to be handled and accepted for processing.
INT sfpsCPResourcesTotalRate	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.30	INTEGER	read-only	The number of packets per second that have been sent to this Call Processor to be handled.
INT sfpsCPResourcesSingleFlood	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.34	INTEGER	read-only	Number of packets that were unicast (single) flooded.
INT sfpsCPResourcesNeedValidNet	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.35	INTEGER	read-only	Number of packets that were unicast (single) flooded.
INT sfpsCPResourcesInvalidNetDrops	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.36	INTEGER	read-only
INT sfpsCPResourcesPersistMask	1.3.6.1.4.1.52.4.2.4.2.2.2.3.1.1.37	INTEGER	read-only
sfpsCPResourcesAPI	1.3.6.1.4.1.52.4.2.4.2.2.2.3.2
INT sfpsCPResourcesAPIID	1.3.6.1.4.1.52.4.2.4.2.2.2.3.2.1	INTEGER	read-write	Identifier for the call processor.
INT sfpsCPResourcesAPIAdminStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.3.2.2	INTEGER	read-write	Administrative status of the call processor.
INT sfpsCPResourcesAPIAttribute	1.3.6.1.4.1.52.4.2.4.2.2.2.3.2.3	INTEGER	read-write	Call processor attribute/features.
INT sfpsCPResourcesAPIScope	1.3.6.1.4.1.52.4.2.4.2.2.2.3.2.4	INTEGER	read-write	Scope this attribute to switch or port.
INT sfpsCPResourcesAPIPersistance	1.3.6.1.4.1.52.4.2.4.2.2.2.3.2.5	INTEGER	read-write	Parameter to make persistent on switch reset.
INT sfpsCPResourcesAPIVerb	1.3.6.1.4.1.52.4.2.4.2.2.2.3.2.6	INTEGER	read-write	Action to perform.
sfpsServiceCenterFacilityTable	1.3.6.1.4.1.52.4.2.4.2.2.2.4.9		not-accessible	This table gives facility semantics to call processing.
sfpsServiceCenterFacilityEntry	1.3.6.1.4.1.52.4.2.4.2.2.2.4.9.1		not-accessible	Each entry contains the configuration of the Facility Entry.
NUM sfpsServiceCenterFacilityHashLeaf	1.3.6.1.4.1.52.4.2.4.2.2.2.4.9.1.1	HexInteger	read-only	Server hash, part of instance key.
INT sfpsServiceCenterFacilityMetric	1.3.6.1.4.1.52.4.2.4.2.2.2.4.9.1.2	INTEGER	read-only	Defines order servers are called low to high.
STR sfpsServiceCenterFacilityName	1.3.6.1.4.1.52.4.2.4.2.2.2.4.9.1.3	DisplayString	read-only	Server name.
INT sfpsServiceCenterFacilityOperStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.4.9.1.4	INTEGER	read-only	Operational state of entry.
INT sfpsServiceCenterFacilityAdminStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.4.9.1.5	INTEGER	read-write	Administrative State of Entry.
TIK sfpsServiceCenterFacilityStatusTime	1.3.6.1.4.1.52.4.2.4.2.2.2.4.9.1.6	TimeTicks	read-only	Time Tick of last operStatus change.
INT sfpsServiceCenterFacilityRequests	1.3.6.1.4.1.52.4.2.4.2.2.2.4.9.1.7	INTEGER	read-only	Requests made to server.
INT sfpsServiceCenterFacilityReply	1.3.6.1.4.1.52.4.2.4.2.2.2.4.9.1.8	INTEGER	read-only	GOOD replies by server.
sfpsCSPControlTable	1.3.6.1.4.1.52.4.2.4.2.2.2.5.1		not-accessible	Cabletron Switch Protocol Control statistics
sfpsCSPControlTableEntry	1.3.6.1.4.1.52.4.2.4.2.2.2.5.1.1		not-accessible
INT sfpsCSPControlTableIndex	1.3.6.1.4.1.52.4.2.4.2.2.2.5.1.1.1	INTEGER	read-only
INT sfpsCSPControlTableCSPType	1.3.6.1.4.1.52.4.2.4.2.2.2.5.1.1.2	INTEGER	read-only
STR sfpsCSPControlTableCSPName	1.3.6.1.4.1.52.4.2.4.2.2.2.5.1.1.3	DisplayString	read-only
INT sfpsCSPControlTableAdminStatus	1.3.6.1.4.1.52.4.2.4.2.2.2.5.1.1.4	INTEGER	read-write
INT sfpsCSPControlTableSwitchToCallProc	1.3.6.1.4.1.52.4.2.4.2.2.2.5.1.1.5	INTEGER	read-only
INT sfpsCSPControlTablePktsProcessed	1.3.6.1.4.1.52.4.2.4.2.2.2.5.1.1.6	INTEGER	read-only
INT sfpsCSPControlTablePktRate	1.3.6.1.4.1.52.4.2.4.2.2.2.5.1.1.7	INTEGER	read-only
sfpsBlockSourceTable	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1		not-accessible	The SourceBlocker table lists all nodes (MAC addresses) that have been heard locally on the switch. Only a certain subset (if any) of the nodes in this table are blocked.
sfpsBlockSourceEntry	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1		not-accessible	Entry in the SourceBlocker table indexed by a counter.
INT sfpsBlockSourceIndex	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1.1	INTEGER	read-only	The index into the table
ADR sfpsBlockSourceMAC	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1.2	SfpsAddress	read-only	The MAC address of the node.
TIK sfpsBlockSourceElapTimeShort	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1.3	TimeTicks	read-only	The elapsed time (seconds) in the current short-threshold period.
INT sfpsBlockSourceNumCallsShort	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1.4	INTEGER	read-only	The number of packets seen from the node during the elapsed time for the short-threshold.
TIK sfpsBlockSourceElapTimeLong	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1.5	TimeTicks	read-only	The elapsed time (seconds) in the current long-threshold period.
INT sfpsBlockSourceNumCallLong	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1.6	INTEGER	read-only	The number of packets seen from the node during the elapsed time for the long-threshold.
INT sfpsBlockSourceBlockFlag	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1.7	INTEGER	read-only	Describes whether the node is blocked or not. There are three possible integer values for this field: 0-notBlocked, 1-Blocked, 2-WouldBeBlocked. The WouldBeBlocked value is used to represent a node that would be in the blocked state if the SourceBlocker was enabled. A node can get into this state only if the blocker is disabled. If the blocker is enabled at this point, the node will be blocked, and a connection filter will be put in place when the next packet is received from this node.
INT sfpsBlockSourceUnBlockableFlag	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1.8	INTEGER	read-only	Flags a node as either Blockable(0) or Unblockable(1). When a node is unblockable, it will never be blocked regardless of the number of packets it sends. The default setting is blockable. Any node can be changed to unblockable via the Source Blocker API (SBAPI).
INT sfpsBlockSourceFilterPresent	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1.9	INTEGER	read-only	Flags whether or not a connection filter is in place for the given node. (This attribute cannot be changed on its own and is therefore used only for diagnostic purposes. It is used internally so that only one filter connection will be mapped per node.)
INT sfpsBlockSourceNext	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1.10	INTEGER	read-only	If this node entry (instance) is part of a hash chain, the NEXT leaf will contain the index to the next node entry in the chain. Otherwise, it will contain -1.
INT sfpsBlockSourceBlocksOnlyIndex	1.3.6.1.4.1.52.4.2.4.2.2.14.1.1.1.11	INTEGER	read-only	Contains the index into the BlockSourceOnly table or the UnblockableOnly table depending on the entry flags. If the 'blocked flag' is set, this value represents the index into the BlockSourceOnly table. If the 'unblockable' flag is set, this value represents the index into the UnblockableOnly table. Otherwise, this value is set to -1 (representing that it is not used.)
sfpsBlockSourceOnlyTable	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1		not-accessible	The format of the BlockSourceOnly Table is exactly the same as the SourceBlocker Table. The only difference is that the entries in this table are only a subset of the entries in the SourceBlocker Table. Only the entries that have a BLOCKFLAG set to 'blocked' or 'would-be-blocked' will reside in this table.
sfpsBlockSourceOnlyEntry	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1		not-accessible	Entry in the BlockSourceOnly table indexed by a counter.
INT sfpsBlockSourceOnlyIndex	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1.1	INTEGER	read-only	The index into the table
ADR sfpsBlockSourceOnlyMAC	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1.2	SfpsAddress	read-only	The MAC address of the node.
TIK sfpsBlockSourceOnlyElapTimeShort	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1.3	TimeTicks	read-only	The elapsed time (seconds) in the current short-threshold period.
INT sfpsBlockSourceOnlyNumCallsShort	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1.4	INTEGER	read-only	The number of packets seen from the node during the elapsed time for the short-threshold.
TIK sfpsBlockSourceOnlyElapTimeLong	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1.5	TimeTicks	read-only	The elapsed time (seconds) in the current long-threshold period.
INT sfpsBlockSourceOnlyNumCallLong	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1.6	INTEGER	read-only	The number of packets seen from the node during the elapsed time for the long-threshold.
INT sfpsBlockSourceOnlyBlockFlag	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1.7	INTEGER	read-only	Describes whether the node is blocked or not. There are three possible integer values for this field: 0-notBlocked, 1-Blocked, 2-WouldBeBlocked. The WouldBeBlocked value is used to represent a node that would be in the blocked state if the SourceBlocker was enabled. A node can get into this state only if the blocker is disabled. If the blocker is enabled at this point, the node will be blocked, and a connection filter will be put in place when the next packet is received from this node.
INT sfpsBlockSourceOnlyUnBlockableFlag	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1.8	INTEGER	read-only	Flags a node as either Blockable(0) or Unblockable(1). When a node is unblockable, it will never be blocked regardless of the number of packets it sends. The default setting is blockable. Any node can be changed to unblockable via the Source Blocker API (SBAPI).
INT sfpsBlockSourceOnlyFilterPresent	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1.9	INTEGER	read-only	Flags whether or not a connection filter is in place for the given node. (This attribute cannot be changed on its own and is therefore used only for diagnostic purposes. It is used internally so that only one filter connection will be mapped per node.)
INT sfpsBlockSourceOnlyNext	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1.10	INTEGER	read-only	If this node entry (instance) is part of a hash chain, the NEXT leaf will contain the index to the next node entry in the chain. Otherwise, it will contain -1.
INT sfpsBlockSourceOnlyBlocksOnlyIndex	1.3.6.1.4.1.52.4.2.4.2.2.14.2.1.1.11	INTEGER	read-only	Contains the index into the BlockSourceOnly table or the UnblockableOnly table depending on the entry flags. If the 'blocked' flag is set, this value represents the index into the BlockSourceOnly table. If the 'unblockable' flag is set, this value represents the index into the UnblockableOnly table. Otherwise, this value is set to -1 (representing that it is not used.)
sfpsBlockSourcePortTable	1.3.6.1.4.1.52.4.2.4.2.2.14.3.1		not-accessible	The SourceBlock API allows for administratively selecting a port and flagging it as 'unblockable'. The BlockSourcePort table shows which ports are set to 'unblockable' and which ones remain set to the default 'blockable' setting.
sfpsBlockSourcePortEntry	1.3.6.1.4.1.52.4.2.4.2.2.14.3.1.1		not-accessible	Entry into the BlockSourcePort Table
INT sfpsBlockSourcePortPort	1.3.6.1.4.1.52.4.2.4.2.2.14.3.1.1.1	INTEGER	read-only	This is the instance part of the table. There will be as many instances as there are logical ports in the device. The attributes represented in subsequent leaves all pertain to this port instance.
INT sfpsBlockSourcePortBlockability	1.3.6.1.4.1.52.4.2.4.2.2.14.3.1.1.2	INTEGER	read-only	This leaf contains either 0-blockable or 1-unblockable, depending on whether nodes on this port are allowed to be blocked or not.
INT sfpsBlockSourceAPIVerb	1.3.6.1.4.1.52.4.2.4.2.2.14.4.1	INTEGER	read-write	Other -- N/A Disable -- disable the source blocker (nodes that are currently blocked will remain blocked, but no additional nodes will be blocked) Enable -- enable the source blocker (allow it to start blocking nodes) ClearAll -- clear the entire block table (this does not remove any connection filters, and should only be used as a diagnostic tool.) BlockMac -- administratively block a node (The node's MAC address must be previously set in the MAC leaf.) UnblockMac -- administratively unblock a node (The node's MAC address must be previously set in the MAC leaf.) SetMacUnblockable -- administratively mark a node as 'unblockable' so that it cannot be blocked. (The node's MAC must be previously set in the MAC leaf.) If the relevant node is blocked at the time the SetMacUnblockable command is issued, the node will automatically be 'unblocked' first. SetMacBlockable -- administratively mark a node as 'blockable' so that it can be blocked. (The node's MAC must be previously set in the MAC leaf.) SetPortUnblockable -- administratively mark a port as 'unblockable' so that any nodes on that port cannot be blocked. (The port number must be previously set in the Port leaf.) SetPortBlockable -- administratively mark a port as 'blockable' so that all nodes on that port can be blocked. (The port number must be previously set in the Port leaf.) SetReapUserCnx -- administratively mark a port as 'blocked' so that administratively mark a port as 'blockable' so that.)
INT sfpsBlockSourceAPIInputValue	1.3.6.1.4.1.52.4.2.4.2.2.14.4.2	INTEGER	read-write	Set the input value to enter
INT sfpsBlockSourceAPIPort	1.3.6.1.4.1.52.4.2.4.2.2.14.4.3	INTEGER	read-write	Read/Write leaf used in conjunction with SetPortUnblockable and SetPortBlockable. (values of 1 through numLogicalPorts are valid.
ADR sfpsBlockSourceAPIMAC	1.3.6.1.4.1.52.4.2.4.2.2.14.4.4	SfpsAddress	read-write	Leaf used to set the MAC address that will be operated on with one of the above verbs.
INT sfpsBlockSourceAPIBlockStatus	1.3.6.1.4.1.52.4.2.4.2.2.14.4.5	INTEGER	read-write	Status of the blocker object (enabled/disabled.) Additional nodes will be blocked only when this status leaf is in the 'enabled' state.
INT sfpsBlockSourceAPIShortThreshold	1.3.6.1.4.1.52.4.2.4.2.2.14.4.6	INTEGER	read-write	The number of packets per a SHORTPERIOD that will result in a node being blocked. This can be changed by writing directly to this leaf. The only limit imposed on this value is that it has to be positive (greater than zero.) There is no upper bound except for what is implied by the size of an integer.
INT sfpsBlockSourceAPIShortPeriod	1.3.6.1.4.1.52.4.2.4.2.2.14.4.7	INTEGER	read-write	The sample period to use for determining if any given node has exceeded the SHORTTHRESHOLD. See SHORTTHRESHOLD for bounds checking for this value
INT sfpsBlockSourceAPILongThreshold	1.3.6.1.4.1.52.4.2.4.2.2.14.4.8	INTEGER	read-write	The number of packets per a LONGPERIOD that will result in a node being blocked. See SHORTTHRESHOLD for bounds checking for this value.
INT sfpsBlockSourceAPILongPeriod	1.3.6.1.4.1.52.4.2.4.2.2.14.4.9	INTEGER	read-write	The sample period to use for determining if any given node has exceeded the LONGTHRESHOLD. See SHORTTHRESHOLD for bounds checking for this value.
INT sfpsBlockSourceAPIReapUserCnxs	1.3.6.1.4.1.52.4.2.4.2.2.14.4.10	INTEGER	read-write	The sample period to use for determining if any given node has exceeded the LONGTHRESHOLD. See SHORTTHRESHOLD for bounds checking for this value.
sfpsBlockSourceExcludeTable	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1		not-accessible	The format of the UnblockableOnly Table is exactly the same as the SourceBlocker Table. The only difference is that the entries in this table are only a subset of the entries in the SourceBlocker Table. Only the entries that have an UNBLOCKABLEFLAG set to 'unblockable' will show up in this table.
sfpsBlockSourceExcludeEntry	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1		not-accessible	Entry in the BlockSourceOnly table indexed by a counter.
INT sfpsBlockSourceExcludeIndex	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1.1	INTEGER	read-only	The index into the table
ADR sfpsBlockSourceExcludeMAC	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1.2	SfpsAddress	read-only	The MAC address of the node.
TIK sfpsBlockSourceExcludeElapTimeShort	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1.3	TimeTicks	read-only	The elapsed time (seconds) in the current short-threshold period.
INT sfpsBlockSourceExcludeNumCallsShort	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1.4	INTEGER	read-only	The number of packets seen from the node during the elapsed time for the short-threshold
TIK sfpsBlockSourceExcludeElapTimeLong	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1.5	TimeTicks	read-only	The elapsed time (seconds) in the current long-threshold period
INT sfpsBlockSourceExcludeNumCallLong	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1.6	INTEGER	read-only	The number of packets seen from the node during the elapsed time for the long-threshold.
INT sfpsBlockSourceExcludeBlockFlag	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1.7	INTEGER	read-only	Describes whether the node is blocked or not. There are three possible integer values for this field: 0-notBlocked, 1-Blocked, 2-WouldBeBlocked. The WouldBeBlocked value is used to represent a node that would be in the blocked state if the SourceBlocker was enabled. A node can get into this state only if the blocker is disabled. If the blocker is enabled at this point, the node will be blocked, and a connection filter will be put in place when the next packet is received from this node
INT sfpsBlockSourceExcludeUnBlockableFlag	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1.8	INTEGER	read-only	Flags a node as either Blockable(0) or Unblockable(1). When a node is unblockable, it will never be blocked regardless of the number of packets it sends. The default setting is blockable. Any node can be changed to unblockable via the Source Blocker API (SBAPI).
INT sfpsBlockSourceExcludeFilterPresent	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1.9	INTEGER	read-only	Flags whether or not a connection filter is in place for the given node. (This attribute cannot be changed on its own and is therefore used only for diagnostic purposes. It is used internally so that only one filter connection will be mapped per node.)
INT sfpsBlockSourceExcludeNext	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1.10	INTEGER	read-only	If this node entry (instance) is part of a hash chain, the NEXT leaf will contain the index to the next node entry in the chain. Otherwise, it will contain -1
INT sfpsBlockSourceExcludeBlockSourceOnlyIndex	1.3.6.1.4.1.52.4.2.4.2.2.14.5.1.1.11	INTEGER	read-only	Contains the index into the BlockSourceOnly table or the UnblockableOnly table depending on the entry flags. If the 'blocked' flag is set, this value represents the index into the BlockSourceOnly table. If the 'unblockable' flag is set, this value represents the index into the UnblockableOnly table. Otherwise, this value is set to -1 (representing that it is not used
INT sfpsBlockSourceStatsNumBlocks	1.3.6.1.4.1.52.4.2.4.2.2.14.6.1	INTEGER	read-only
INT sfpsBlockSourceStatsNumCollisions	1.3.6.1.4.1.52.4.2.4.2.2.14.6.2	INTEGER	read-only	The number of hash collisions resulting in a chain of nodes. (diagnostic only.)
INT sfpsBlockSourceStatsLongestChain	1.3.6.1.4.1.52.4.2.4.2.2.14.6.3	INTEGER	read-only	The maximum number of nodes in a linked list chain (including the hash bucket itself) due to hashing collisions. (diagnostic only.)
INT sfpsBlockSourceStatsNumEntries	1.3.6.1.4.1.52.4.2.4.2.2.14.6.4	INTEGER	read-only	The number of entries in the SourceBlocker table. (Each new node that is heard has its own entry.
INT sfpsBlockSourceStatsMaxNumEntries	1.3.6.1.4.1.52.4.2.4.2.2.14.6.5	INTEGER	read-only	The maximum number of entries that can fit in the SourceBlocker Table. (This currently mirrors the size of the Directory's NodeTable.)
INT sfpsBlockSourceStatsSizeOfObj	1.3.6.1.4.1.52.4.2.4.2.2.14.6.6	INTEGER	read-only	The size of the SourceBlocker object itself (in bytes.)
INT sfpsBlockSourceStatsHashModValue	1.3.6.1.4.1.52.4.2.4.2.2.14.6.7	INTEGER	read-only	The value that is used for the modulus operation in the hashing algorythm.
INT sfpsBlockSourceStatsHashSlotsSize	1.3.6.1.4.1.52.4.2.4.2.2.14.6.8	INTEGER	read-only	The amount of storage used for the hash buckets (in bytes.)
INT sfpsBlockSourceStatsTableSize	1.3.6.1.4.1.52.4.2.4.2.2.14.6.9	INTEGER	read-only	The amount of storage used for the SourceBlocker Table (in bytes.)
INT sfpsBlockSourceStatsBlockSourceOnlySize	1.3.6.1.4.1.52.4.2.4.2.2.14.6.10	INTEGER	read-only	The amount of storage used for the Blocks-Only index array (in bytes.)
INT sfpsBlockSourceStatsUnblockableSize	1.3.6.1.4.1.52.4.2.4.2.2.14.6.11	INTEGER	read-only	The amount of storage used for the Unblockable-Only index array (in bytes.)
INT sfpsBlockSourceStatsPortMaskSize	1.3.6.1.4.1.52.4.2.4.2.2.14.6.12	INTEGER	read-only	The amount of storage used for the port mask object (in bytes.)
INT sfpsBlockSourceStatsTotalHeapBytes	1.3.6.1.4.1.52.4.2.4.2.2.14.6.13	INTEGER	read-only	The total amount of heap memory used for all data storage (above) including the SourceBlocker object itself (in bytes.)
OCT sfpsDHCPServerVLANName	1.3.6.1.4.1.52.4.2.4.2.2.15.1	OCTET STRING	read-write
INT sfpsDHCPServerVLANSingleFloodStatus	1.3.6.1.4.1.52.4.2.4.2.2.15.2	INTEGER	read-write
INT sfpsDHCPServerVLANVersion	1.3.6.1.4.1.52.4.2.4.2.2.15.3	INTEGER	read-only
OCT sfpsATalkAMRVLANControlName	1.3.6.1.4.1.52.4.2.4.2.2.16.1	OCTET STRING	read-write
INT sfpsATalkAMRVLANControlVersion	1.3.6.1.4.1.52.4.2.4.2.2.16.2	INTEGER	read-only

RFC description

Cabletron SFPS Fast Packet Switching Services call processor resource management.

Start monitoring Cabletron SecureFast Packet Switch (SFPS) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CTRON-SFPS-BASE-MIB

What Is CTRON-SFPS-BASE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description